PHILIPS DS8800W User Manual

Register your product and get support at
www.philips.com/welcome
DS8800W
User manual
2

Contents

Safety 4 Notice 5
2 Your Entertainment System
Introduction 7 What’s in the box 7 What else you need 7 Overview of the main unit 7 Overview of the remote control 8
3 Prepare
Connect 9
4 Set up a Wi-Fi network for AirPlay
Connect the unit to a Wi-Fi network (router) 11 Connect an AirPlay device to the same Wi-Fi network 16
5 Play
Stream audio from your AirPlay device 17 Control play 18 Advanced sound settings 18
Update rmware 18
6 Other features
Play from an external device (optional) 20 Charge your iPod/iPhone/iPad 20
11
17
20
English
7
9
7 Product information
Specications 21
8 Troubleshooting
21
22
EN
3

1 Important

Safety

Information for Europe: Know these safety symbols
This ‘bolt of lightning’ indicates uninsulated material within the device may cause an electrical shock. For the safety of everyone in your household, please do not remove the covering. The ‘exclamation mark’ calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems.
WARNING: To reduce the risk of re or
electric shock, the device should not be
exposed to rain or moisture and objects lled
with liquids, such as vases, should not be placed on the device.
CAUTION: To prevent electric shock, fully insert the plug. (For regions with polarized plugs: To prevent electric shock, match wide blade to wide slot.)
a Read these instructions. b Keep these instructions. c Heed all warnings. d Follow all instructions. e Do not use this product near water. f Clean only with dry cloth. g Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
h Do not remove the casing of this product. i Do not expose the product to dripping /
splashing water, rain or high humidity.
j Keep this product away from direct
sunlight, naked ames or heat.
k Do not install near any heat sources
such as radiators, heat registers, stoves, or other electrical equipment (including
ampliers).
l Do not place any other electrical
equipment on the product.
m Do not place any sources of danger
on the product (e.g. objects containing
liquids, burning candles).
n This product may include batteries. Please
refer to safety and disposal instructions for batteries in this user manual.
o Where the mains plug or an appliance
coupler is used as the disconnect device, the disconnect device shall remain readily operable.
Warning
Never remove the casing of this apparatus.
• Never lubricate any part of this apparatus.
• Never place this apparatus on other electrical
equipment.
• Keep this apparatus away from direct sunlight, naked
ames or heat.
• Ensure that you always have easy access to the power
cord, plug or adaptor to disconnect this apparatus from the power.
Risk of overheating! Never install this apparatus
in a conned space. Always leave a space of
at least four inches around this apparatus for ventilation. Ensure curtains or other objects never cover the ventilation slots on this apparatus.
4
EN
Mains fuse
This information applies only to products with a UK mains plug.
This product is tted with an approved molded
plug. If you replace the fuse, use one with:
the ratings shown on the plug,
a BS 1362 approval, and
the ASTA approval mark.
Contact your dealer if you are not sure about what type of fuse to use. Caution: To conform with the EMC directive (2004/108/EC), do not detach the plug from the power cord.

Notice

When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002/96/ EC. Please inform yourself about the local separate collection system for electrical and electronic products. Please act according to your local rules and do not dispose of your old products with your normal household waste. Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health.
English
This product complies with the radio interference requirements of the European Community.
This product complies with the requirement of the 1999/5/EC directive. A copy of the EC declaration of Conformity is available in the Portable Document Format (PDF) version of the user manual at www. philips.com/support.
Modications
Modications not authorized by the
manufacturer may void user’s authority to operate this product.
Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.
Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be disposed with normal household waste.Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health.
Information about the use of batteries:
Caution
Risk of leakage: Only use the specied type of batteries.
Do not mix new and used batteries. Do not mix different brands of batteries. Observe correct polarity. Remove batteries from products that are not in use for a longer period of time. Store batteries in a dry place.
• Risk of injury: Wear gloves when handling leaking
batteries. Keep batteries out of reach of children and pets.
• Risk of explosion: Do not short circuit batteries. Do
not expose batteries to excessive heat. Do not throw
batteries into the re. Do not damage or disassemble
batteries. Do not recharge non-rechargeable batteries.
Environmental information
All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box),
EN
5
polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.
“Made for iPod,” “Made for iPhone,” and “Made for iPad” mean that an electronic accessory
has been designed to connect specically to
iPod, iPhone, or iPad, respectively, and has
been certied by the developer to meet
Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance. AirPlay, iPod, and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. iPad is a trademark of Apple Inc.
Note
The type plate is located on the bottom of the
apparatus.
Norge
Typeskilt nnes på apparatens underside.
Observer : Nettbryteren er sekunder t innkoplet. Den innebygde netdelen er derfor ikke frakoplet
nettet så lenge apparatet er tilsluttet nettkontakten. For å redusere faren for brann eller elektrisk
støt, skal apparatet ikke utsettes for regn eller fuktighet.
6
EN
e f
c d
b
a
2 Your

What’s in the box

Entertainment System
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product at www.philips.com/welcome. If you contact Philips, you will be asked for the model and serial number of this apparatus. The model number and serial number are on the bottom of the apparatus. Write the numbers here: Model No. __________________________ Serial No. ___________________________

Introduction

With this unit, you can:
stream audio from your iOS 4.2 (or later) enabled device (e.g., an iPod touch/iPhone/iPad) wirelessly by AirPlay.
stream audio from your Wi-Fi enabled PC or Mac installed with iTunes 10 (or later) wirelessly by AirPlay.
play audio from other audio devices through the AUX IN socket.
charge your iPod/iPhone/iPad through the USB socket with a USB cable (not supplied).
Check and identify the contents of your package:
Main unit
Remote control
2 x AC power cords
1 x MP3 link cable
Desk top adaptor
User manual
Quick start guide

What else you need

To stream audio wirelessly by AirPlay, you need:
A wireless router that is powered on and working properly.
An AirPlay device (e.g., an iOS 4.2 (or later) enabled iPod touch/iPhone/iPad or Wi-Fi enabled PC or Mac installed with iTunes 10 (or later)).

Overview of the main unit

English
EN
7
g
f
b
a
e
d
c
a
b VOLUME +/-
c DC IN
d AUX IN
e USB
f WI-FI SETUP
Turn on/off the unit.
(Press and hold) reset the unit.
As the indicator to show the current
status of the unit.
Adjust volume.
Power socket of the unit.
Socket for an external audio player.
USB socket.
Connect the unit to a Wi-Fi network.

Overview of the remote control

a
Turn on/off the unit.
b
Select the AirPlay device audio source.
c +/-
Adjust volume.
d
Mute or restore volume.
e
/
Skip to the previous/next track.
f
Start or pause play.
g
Select the AUX IN audio source.
8
EN

3 Prepare

» After boot-up, the indicator starts to
blink in green slowly.
Always follow the instructions in this chapter in sequence.

Connect

Connect power

Caution
Risk of product damage! Ensure that the power supply
voltage corresponds to the voltage printed on the bottom of the unit.
• Risk of electric shock! When you unplug the AC
adaptor, always pull the plug from the socket. Never pull the cord.
• Before connecting the AC adaptor, ensure you have
completed all other connections.
1 Insert the plug from the AC adaptor to
the DC IN socket on the back of the main unit.
2 Connect one end of the AC power cord
to the AC adaptor.

Switch on or to standby mode

The unit switches on automatically after power connection.
To switch the unit to standby mode, press on the front of the main unit.
To switch the unit on from the standby
mode, press

Prepare the remote control

Caution
Risk of explosion! Keep batteries away from heat,
sunshine or re. Never discard batteries in re.
• Perchlorate Material - special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate.
For rst-time use:
1 Remove the protective tab to activate the
remote control battery.
To replace the remote control battery:
1 Open the battery compartment. 2 Insert one CR2025 battery with correct
polarity (+/-) as indicated.
again.
English
3 Connect the other end of the AC power
cord to the wall outlet.
» It takes about 35 seconds for the main
unit to boot up. During boot-up, the indicator on the front of the main unit blinks in green quickly.
9
EN
3 Close the battery compartment.
Note
Before pressing any function button on the remote
control, rst select the correct source with the remote
control instead of the main unit.
• If you are not going to use the remote control for a
long time, remove the battery.
10
EN
WIFI
SETUP
WI-FI SETUP
4 Set up a Wi-
Fi network for AirPlay
Note
Some operations may vary as you use different types of
wireless routers.
The unit is compatible with the following iPod/ iPhone/iPad models:
iPod touch (2nd, 3rd, and 4th generation)
iPhone 4
iPhone 3GS
iPad 2
iPad
Connect the unit to a Wi-Fi
network (router)
Select a scenario below that matches your router type.
Note
Each time when the unit is powered on again, the
unit enters the latest congured Wi-Fi network
automatically.
• In case of setup failure, repeat the steps, or press and
hold
on the front of the main unit and try again.

Scenario 1: Connect to a WPS-PBC router

1 Press WI-FI SETUP on the back of the
main unit.
» The
indicator blinks in red, green, and
yellow alternately.
English
Before setup of the Wi-Fi network, check the points below.
1 Make sure that the wireless router is
powered on and working properly.
2 Make sure that the indicator on the front
of the main unit blinks in green slowly.
3 Check the type of the wireless router you
use.
2 Press the WPS button on the wireless
router.
» After a while, the
blinking and stays green, and the speaker beeps.
» The unit joins the Wi-Fi network
successfully.
indicator stops
EN
11
Philips Fidelio AirPlay
WPS
Tip
To change the name of the unit for AirPlay, proceed
with steps in ‘Scenario 2: Connect to a non-WPS router’ below.
• For some wireless routers, you may need to hold the
WPS button for WPS connection. See the user manuals
of the specic routers for details.

Scenario 2: Connect to a non-WPS router

You can connect the unit to a non-WPS router through
an iOS 4.2 (or later) enabled iPod touch/iPhone/iPad
a Wi-Fi enabled PC or Mac installed with iTunes 10 (or later)
3 Select Settings -> Wi-Fi on your iPod
touch/iPhone/iPad.
Or enter the list of available wireless networks on your PC/Mac.
4 Select Philips Fidelio AirPlay from the list
of available networks.

Connect DS8800W to your iPod touch/iPhone/iPad or PC/Mac

1 Press and hold WI-FI SETUP on the back
of the main unit for more than 5 seconds.
» The
indicator blinks in green and
yellow alternately.
2 Wait for about 45 seconds so that Philips
Fidelio AirPlay is available in the list of Wi-
Fi networks.
12
EN
Network Configuration
5 Wait until successful Wi-Fi connection to
192.168.1.1
the unit.
» A Wi-Fi signal icon is displayed on the
iPod touch/iPhone/iPad or PC/Mac.
Congure Wi-Fi connection from
DS8800W to your wireless router
1 Open Safari on your iPod touch/iPhone/
iPad, and then type in 192.168.1.1 at the address bar.
Or open Safari on your PC/Mac, and then select ‘Philips_Fidelio XXX’ from the bonjour pull-down list.
Or open another web browser on your PC/Mac, and then type in
192.168.1.1 at the address bar.
» The DS8800W conguration
page is displayed.
2 Select the Network Conguration tab.
English
3 Change the name of the unit in AirPlay
Device Name if you like.
EN
13
4 Select your router SSID from the pull-
down list of Service Set ID (SSID).
5 Enter your network key if required (for
some routers, you may also need to tick DHCP under Advance Setting).
14
EN
6 Click Apply at the bottom of the page to
apply your settings.
» A menu for conrmation of your set
parameters pops up.
7 Click OK on the popup menu to conrm
your settings.
» After a while, the
blinking and stays green, and the speaker beeps.
» The unit joins the Wi-Fi network
successfully.
indicator stops
English
EN
15

Connect an AirPlay device to the same Wi-Fi network

To work together with the unit, your AirPlay device is required to join the same Wi-Fi network as the unit.
1 Select Settings -> Wi-Fi on your iPod
touch/iPhone/iPad.
Or enter the list of available wireless networks on your PC/Mac.
2 Select your router SSID from the list of
available wireless networks.
3 Wait until successful Wi-Fi connection to
the router.
» A Wi-Fi signal icon is displayed on the
AirPlay device.
16
EN

5 Play

3 Select Philips_Fidelio XXXX (or user
customized name) from the list.

Stream audio from your AirPlay device

Note
Make sure that the AirPlay device is connected to the
same Wi-Fi network as the unit.
Stream from your iOS 4.2 (or later)
enabled iPod touch/iPhone/iPad
1 Open iPod. 2 Tap on the AirPlay icon.
English
4 Select a media le and start play.
5 Wait until successful audio streaming to
the speakers.
EN
17
Stream from your Wi-Fi enabled PC or Mac installed with iTunes 10 (or
later)
Note
Before you open iTunes, make sure that you have
enabled Bonjour service in your PC. Take Windows XP for example: to enable the service, you can click
Start->Settings->Control Panel, and double-click Administrative Tools-> Services->Bonjour Service,
and then click Start followed by OK on the pop-up menu.
1 Open iTunes 10 (or later). 2 Click the AirPlay icon at the bottom right
corner of the window.
3 Select Philips_Fidelio_AirPlay XXXX (or
user customized name) from the list.
4 Select a media le and start play. 5 Wait until successful audio streaming to
the speaker.

Advanced sound settings

For advanced sound settings and additional features, you can use your AirPlay device to download the Philips Fidelio application from Apple App Store.
Update rmware
Note
You can only update the rmware from a PC/Mac.
Download the update le
1 On your PC/Mac, go to www.philips.com/
support.
2 Enter the model number to nd the latest
rmware upgrade le available.
3 Save the upgrade le to your hard drive.

Control play

You can select different play options from either your AirPlay device or the supplied remote control.
Note
All the operations below are based on the supplied
remote control.
To star t or pause play, press .
To skip to the previous or next track, press
/ .
To adjust volume, press +/- repeatedly.
To mute or restore volume, press
To switch to the AUX IN source (if
connected), press
To switch back to the AirPlay device source, press
18
EN
.
.
.
Update from the conguration page
1 Power on the unit (see ‘Prepare - Connect
- Connect power’).
» It takes about 35 seconds for the unit
to boot up. During boot-up, the indicator on the front of the main unit blinks in green quickly.
» After boot-up, the
blink in green slowly.
indicator starts to
2 Make sure that the unit and PC/Mac are
connected to the same wireless router.
3 Open Safari on your PC/Mac, and then
select ‘Philips_Fidelio XXX’ from the bonjour pull-down list.
Or open the web browser on your
PC/Mac, and then type in the IP address of DS8800W (available on
the router conguration page) at the
address bar.
» The DS8800W conguration
page is displayed.
4 Select the Firmware Update tab, and then
follow the on-screen instruction to enter the next page.
5 Click Browse to select the downloaded
rmware update le, and then click Open.
6 Click Upload to upload the le, and then
compare the current and new le versions.
7 After you make sure that the downloaded
update le is the latest, click Ok to start rmware update.
» A progress bar is displayed.
8 At completion of the update process, click
Ok to conrm.
English
EN
19

6 Other features

AUX IN
Play from an external device
(optional)

Charge your iPod/iPhone/iPad

Note
The USB socket only supports Apple devices for
charging (see the list below).
You can also listen to an external audio player through the unit. Connect the supplied MP3 link cable to:
the AUX IN socket on the back of
the main unit.
the headphone jack on an external
audio player.
Note
To play audio from the connected audio player, rst
press
to select the AUX IN source.
You can charge your iPod/iPhone/iPad through the USB socket with a USB cable (not supplied). The USB socket supports the following iPod, iPhone, and iPad models for charging. Made for:
iPod touch (1st, 2nd, 3rd, and 4th generation)
iPod classic
iPod nano (2nd, 3rd, 4th, 5th, and 6th
generation)
iPhone 4
iPhone 3GS
iPhone 3G
iPhone
iPad 2
iPad
20
EN
7 Product
information
Note
Product information is subject to change without prior
notice.
Specications
Amplier
Rated Output Power 2 X 15 W RMS Frequency Response 20 - 20000 Hz, ±3 dB Signal to Noise Ratio > 90 dB Aux Input 650 mV RMS 20 kohm

Speakers

Speaker Impedance 8 ohm Speaker Driver 130 mm woofer + 19
mm tweeter
Sensitivity > 85 dB/m/W
English

General information

AC power Model: GFP451DA-
1825-1 Input: 100 - 240 V~, 50/60 Hz 1.2 A Output: 18 V
Operation Power Consumption
Eco Standby Power Consumption
Dimensions
- Main Unit 455 x 165 x 150 mm Weight
- With Packing
- Main Unit
10 W
< 1 W
3.7 kg
2.5 kg
2.5 A
EN
21

8 Troubleshooting

Warning
Never remove the casing of this apparatus.
To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this apparatus, check the following points before requesting service. If the problem remains unsolved, go to the Philips web site (www.philips.com/support). When you contact Philips, ensure that the apparatus is nearby and the model number and serial number are available.
No power
Make sure that the AC power plug of the device is connected properly.
Make sure that there is power at the AC outlet.
No sound
Adjust the volume.
Check the network connection. Set up the network again if needed (see ‘Set up a Wi­Fi network (router)’).
No response from the unit
Press and hold main unit to reset the device. Set up the network again (see ‘Set up a Wi-Fi network (router)’).
Disconnect and reconnect the AC power plug, and then switch on the device again.
Wi-Fi network connection failed
Check if your Wi-Fi router is Wi-Fi
certied. This device is only compatible with Wi-Fi certied routers.
This device does not suppor t WPS-Pin routers.
This device does not suppor t all WPS- PBC routers (see the user manual of your router).
Enable SSID broadcast on the Wi-Fi router.
on the front of the
Avoid using Wi-Fi channel which is using or much overlapped by the nearby Wi-Fi network.
Keep away from potential sources of interference which may affect Wi-Fi signal, such as microwave ovens.
If you fail to use your PC for Wi-Fi network setup, check whether your PC is using a Wi-Fi network. You cannot use Ethernet connection for AirPlay network setup. If the problem remains, it is strongly recommended to use iPod Touch/iPhone/
iPad/Mac to do the rst-time Wi-Fi setup
as some PC settings may affect the Wi-Fi network setup.
Make sure that the SSID name of your home router consists of normal characters or digits, with no space or special characters like %/#/* inser ted.
If you choose to rename the AirPlay device Philips_Fidelio XXXX’ in the setting menu, do not use special characters or symbols.
If you fail to get connected via WPS, make
sure that you are using a WPS cer tied
router. If the problem remains, do not use the default SSID name for your WPS router. The default SSID name may involve security protection that leads to connection failure. Use simple characters or digits only to rename your WPS router.
Occasional breaking of AirPlay music streaming
Do one or all of the following:
Enable the Auto Channel Scan option (if available on the Wi-Fi router).
Enable the Wireless Intelligent Stream Handling (WISH) option (if available on the Wi-Fi router).
Enable the Quality of Service (QoS) option (if available on the Wi-Fi router).
Turn off other home routers.
22
EN
No AirPlay icon on Apple AirPlay device or iTunes in my PC
Make sure that the unit have already joined the AirPlay network.
Before you open iTunes, make sure that you have enabled Bonjour service in your PC. Take Windows XP for example: to enable the service, you can click Start­>Settings->Control Panel, and double­click Administrative Tools-> Services- >Bonjour Service, and then click Start followed by OK on the pop-up menu.
If the problem remains, try to restart the unit.
AirPlay connection failed with Mac or PC
Disable the rewalls software and security software, which may block ports that AirPlay uses to stream content.
Check if your network speed is fast enough (in cases where multiple devices share the same router, the AirPlay performance may be affected). Turn off the other devices connected to your home router.
In case of audio streaming break or disconnection when you use iPod Touch/ iPhone/iPad/iMac/PC for AirPlay, restart your iPod Touch/iPhone/iPad, iTunes, or DS8800W.
Browsing Internet content like news, music, video and etc. via your home router may affect the AirPlay performance. In case of AirPlay break or disconnection, it is
recommended to stop any Internet surng
or disconnect from the Internet.
English
EN
23
©2013 Koninklijke Philips Electronics N.V.
All rights reserved.
DS8800W_10_UM_V3.0
Loading...