(signature, name and function / signature, nom et fonction)
description de l’intervention)
Philips Consumer Lifystyle AMB 544-9056
Page 3
Contents
1 Important 4
Safety 4
Notice 7
2 Your Docking Speaker 9
Introduction 9
What’s in the box 9
Overview of the main unit 10
Overview of the remote control 11
3 Get started 13
Prepare the remote control 13
Connect power 14
Turn on 16
4 Play 17
Play from iPod/iPhone/iPad 17
Play from Bluetooth device 18
Play from an external device 19
Adjust volume level 20
Mute sound 20
5 Product information 21
Specifications 21
6 Troubleshooting 23
About Bluetooth device 23
Page 4
1 Important
Safety
Important Safety Instructions
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this apparatus near water.
f Clean only with dry cloth.
g Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
h Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
i Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
j Only use attachments/accessories specified by the manufacturer.
k Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
l Unplug this apparatus during lightning storms or when unused for
long periods of time.
4
EN
Page 5
m Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
n Battery usage CAUTION – To prevent battery leakage which may
result in bodily injury, property damage, or damage to the unit,the
batteries (battery pack or batteries installed) shall not be exposed
to excessive heat such as sunshine, fire or the like.
o Apparatus shall not be exposed to dripping or splashing.
p Do not place any sources of danger on the apparatus (e.g. liquid
filled objects, lighted candles).
q Where the MAINS plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain readily
operable.
Safety-Important notes for users in the U.K.
For users in the U.K.: please follow the instructions below
Mains plug
This apparatus is fitted with an approved 13 Amp plug. To change a fuse in
this type of plug proceed as follows:
a Remove fuse cover and fuse.
b Fix new fuse which should be a BS1362 5 Amp, A.S.T.A. or BSI
approved type.
c Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 5 Amp. If
a plug without a fuse is used, the fuse at the distribution board should
not be greater than 5 Amp.
Note: The severed plug must be disposed off to avoid a possible
shock hazard should it be inserted into a 13 Amp socket elsewhere.
English
EN
5
Page 6
How to connect a plug
The wires in the mains lead are coloured with the following code: blue =
neutral (N), brown = live (L).
As these colours may not correspond with the colour markings identifying
the terminals in your plug, proceed as follows:
Connect the blue wire to the terminal marked N or colored black. •
Connect the brown wire to the terminal marked L or colored red.•
Do not connect either wire to the earth terminal in the plug, marked •
E (or ) or colored green (or green and yellow).
Before replacing the plug cover, make certain that the cord grip is clamped
over the sheath of the lead - not simply over the two wires.
Copyright in the U.K.
Recording and playback of material may require consent. see Copyright
Act 1956 and The per former’s Protection Acts 1958 to 1972.
Hearing safety
Listen at a moderate volume.
Using headphones at a high volume can impair your hearing. This •
product can produce sounds in decibel ranges that may cause hearing
loss for a normal person, even for exposure less than a minute. The
higher decibel ranges are offered for those that may have already
experienced some hearing loss.
Sound can be deceiving. Over time your hearing ‘comfort level’ •
adapts to higher volumes of sound. So after prolonged listening, what
sounds ‘normal’ can actually be loud and harmful to your hearing. To
guard against this, set your volume to a safe level before your hearing
adapts and leave it there.
To establish a safe volume level:
Set your volume control at a low setting. •
Slowly increase the sound until you can hear it comfortably and •
clearly, without distortion.
Listen for reasonable periods of time:
Prolonged exposure to sound, even at normally ‘safe’ levels, can also •
cause hearing loss.
Be sure to use your equipment reasonably and take appropriate •
breaks.
6
EN
Page 7
Be sure to observe the following guidelines when using your headphones.
Listen at reasonable volumes for reasonable periods of time.•
Be careful not to adjust the volume as your hearing adapts.•
Do not turn up the volume so high that you can’t hear what’s around •
you.
You should use caution or temporarily discontinue use in potentially •
hazardous situations. Do not use headphones while operating a
motorized vehicle, cycling, skateboarding, etc.; it may create a traffic
hazard and is illegal in many areas.
Warning
Never r emove the casing of this apparatus. •
Never lubricate any par t of this apparatus. •
Never place this apparatus on other electrical equipment. •
Keep this apparatus away from direct sunlight, naked flames or heat. •
Ensur e that you always have easy access to the power cord, plug or adaptor to •
disconnect the apparatus from the power.
Notice
Any changes or modifications made to this device that are not expressly
approved by Philips Consumer Lifestyle may void the user’s authority to
operate the equipment.
This product complies with the radio interference requirements of the
European Community.
Recycling
English
Your product is designed and manufactured with high quality materials and
components, which can be recycled and reused.
When you see the crossed-out wheel bin symbol attached to a product, it
means the product is covered by the European Directive 2002/96/EC:
EN
7
Page 8
Never dispose of your product with other household waste. Please inform
yourself about the local rules on the separate collection of electrical
and electronic products. The correct disposal of your old product helps
prevent potentially negative consequences on the environment and human
health.
Your product contains batteries covered by the European Directive
2006/66/EC, which cannot be disposed of with normal household waste.
Please inform yourself about the local rules on separate collection of
batteries. The correct disposal of batteries helps prevent potentially
negative consequences on the environment and human health.
Always bring your product to a professional to remove the built-in battery.
Environmental information
All unnecessary packaging has been omitted. We have tried to make
the packaging easy to separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused
if disassembled by a specialized company. Please observe the local
regulations regarding the disposal of packaging materials, exhausted
batteries and old equipment.
Norge
Typeskilt finnes på apparatens underside.
Observer: Nettbryteren er sekundert innkoplet. Den innebygde
netdelen er derfor ikke frakoplet nettet så lenge apparatet er tilsluttet
nettkontakten.
For å redusere faren for brann eller elektrisk støt, skal apparatet ikke
utsettes for regn eller fuktighet.
Note
The type plate is located on the bottom of the apparatus . •
8
EN
Page 9
2 Your Docking Speaker
Congratulations on your purchase, and welcome to Philips! To fully benefit
from the support that Philips offers, register your product at www.philips.
com/welcome.
Introduction
With this unit, you can enjoy audio from the iPod/iPhone/iPad and other
audio devices.
What’s in the box
Check and identify the contents of your package:
Main unit•
Remote control•
1 x AC adaptor•
1 x AC power cord•
1 x UK power cord•
1 x Aux-in cable•
1 x iPad stand •
User manual•
Quick Start Guide•
English
EN
9
Page 10
Overview of the main unit
a bd
c
e
a
b
10
Turn on/off the unit.•
Select Bluetooth mode•
Pair with Bluetooth device.•
EN
g f
Page 11
c iPod/iPhone/iPad dock
d
/
Adjust volume. •
e Built-in battery LED indicator
f Power supply socket
g AUX IN
Overview of the remote control
j
i
Jack for an external audio device.•
a
b
c
d
e
English
h
g
f
a
b
c
d Up/down keys
Mute volume.•
Select Bluetooth mode•
Pair with Bluetooth device.•
Select Aux-in mode •
Navigate through the iPod/iPhone menu.•
EN
11
Page 12
e Fast forward/backward keys
f
g VOL +/-
h MENU
i OK
j
Fast reverse or fast forward within a track or iPhone/iPod.•
Skip to the previous/next track.•
Star t or pause play.•
Adjust volume.•
Access the iPod menu.•
Confirm a selection.•
Select iPod/iPhone dock mode•
12
EN
Page 13
3 Get started
Caution
Use of controls or adjustments or performance of procedures other than herein •
may result in hazardous radiation exposure or other unsafe operation.
Always follow the instructions in this chapter in sequence.
If you contact Philips, you will be asked for the model and serial number of
this apparatus. The model number and serial number are on the bottom of
the apparatus. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Prepare the remote control
Caution
Risk of explosion! Keep batteries away from heat, sunshine or fire. Never discard •
batteries in fire.
For first-time use:
1 Remove the protective tab to activate the remote control batter y.
To replace the remote control battery:
1 Open the battery compartment.
2 Insert one CR2032 battery with correct polarity (+/-) as indicated.
3 Close the batter y compartment.
English
EN
13
Page 14
Note
Befor e pressing any function button on the remote control, fir st select the correct •
source with the remote control instead of the main unit.
If you are not going to use the remote control for a long time , remove the battery.
•
Connect power
Caution
Risk of product damage! Ensure that the power supply voltage corresponds to the •
voltage printed on the bottom of the unit.
Risk of electric shock! When you unplug the AC adaptor, always pull the plug from
•
the socket. Never pull the cord.
Befor e connecting the AC adaptor, ensure you have completed all other
•
connections.
1 Insert the plug from the AC adaptor to the DC IN socket on the
back of the main unit.
2 Connect one end of the AC power cord to the AC adaptor.
3 Connect the other end of the AC power cord to the wall outlet.
14
EN
Page 15
Built-in Battery
Note
Always bring your product to a professional to remove the built-in battery. •
Caution
Danger of explosion if bat ter y is incorrectly replaced. Replace only with the same or •
equivalent type.
The unit can also operate on built-in rechargeable battery.
Battery powerLED indicator
LowRed
MediumYellow
FullGreen
Note
Use only the supplied AC adapter to charge the battery. •
To recharge the built-in battery:
Connect the unit to the mains power supply.
English
EN
15
Page 16
Turn on
1 Press on the main unit.
Switch to ECO standby
The unit switches to standby mode automatically, when:
(at DOCK mode) the iPod/iPhone is disconnected from the unit.•
(at AUX mode) the device no longer playing music for more than 5 •
minutes.
(at Bluetooth mode) the Bluetooth device is disconnected from the •
unit for more than 5 minutes.
Tip
In standby mode, press •, or on the remote control, the unit switches on at the
corresponding source.
About ECO power
You can switch the unit to ECO power standby mode to save power
consumption.
1 Press for over 3 seconds.
The unit turns into ECO power mode immediately. »
If the unit is powered via built-in battery, when it is in standby mode »
for 5 minutes, it switches to ECO power mode automatically.
Tip
In ECO power mode, the remote control does not work. •
To exit ECO power mode, press
16
EN
.
Page 17
4 Play
Play from iPod/iPhone/iPad
You can enjoy audio from iPod/iPhone/iPad through this unit.
Compatible iPod/iPhone/iPad
Apple iPod, iPhone and iPad models with a 30-pin dock connector. Made
for :
iPod (5th generation)•
iPod nano (1st generation)•
iPod nano (2nd generation)•
iPod nano (3rd generation)•
iPod nano (4th generation)•
iPod nano (5th generation)•
iPod classic•
iPod touch (1st generation)•
iPod touch (2nd generation)•
iPod touch (3rd generation)•
iPhone•
iPhone 3G•
iPhone 3GS•
iPad.•
Load the iPod/iPhone/iPad
1 Place the iPod/iPhone/iPad in the dock.
English
EN
17
Page 18
Remove the iPod/iPhone/iPad
1 Pull the iPod/iPhone/iPad out of the dock.
Listen to the iPod/iPhone/iPad
Ensure that the iPod/iPhone/iPad is loaded correctly.
1
2 Press to select dock mode.
3 Press .
The connected iPod/iPhone/iPad starts play. »
To pause/resume play, press •
To skip to a track, press fast forward/backward keys.•
To search during play, press and hold fast forward/backward •
keys, then release to resume normal play.
To navigate the menu, press • MENU, then press up/down keysto
select, and press OK to confirm.
.
Charge the iPod/iPhone/iPad
When the unit is connected to AC power, the docked iPod/iPhone/iPad
begins to charge.
Tip
You can also charge your iPod/iPhone via the built-in battery. Before charging your •
iPod/iPhone via the built-in battery, ensur e the Fidelio bat ter y-charging function is
turn on.
You cannot charge your iPad via the built-in battery. To charge your iPad, connect
•
the unit to AC power.
Play from Bluetooth device
Pair with Bluetooth deivces
1 Press to select Bluetooth source.
2 Turn on Bluetooth function on your device.
3 When “PHILIPS DS8550” displays, select it to start connection.
4 When prompted for a password, enter “0000”.
The unit starts searching for Bluetooth device. The Bluetooth »
indicator under button on the main unit flashes rapidly.
18
EN
Page 19
If connection is successful. the unit beeps and the »indicator turns
on stably.
If the pairing cannot be completed within one minute, the »
indicator flashes slowly.
Tip
If your Bluetooth device is already paired with DS8550 before, you just need to find •
out the “PHILIPS DS8550” on your Bluetooth menu, then confirm the connection.
To disconnect Bluetooth device,
Move it beyond the communication range; or•
Press • ; or
Turn off the connected device•
Play audio files from bluetooth devices
Note
Make sure the Bluetooth connection bet ween the unit and the device is ac tive. •
English
To start play, press •
To pause/resume play, press • again.
To track up/down, press for ward/backward keys.•
on the remote control.
Play from an external device
You can also listen to an external audio device through this unit.
1 Press to select Aux-in mode.
2 Connect the supplied Aux-in link cable to:
3 Start to play the device (see the device user manual).
the • AUX IN jack (3.5mm) on the back of the unit.
the headphone jack on an external device.•
EN
19
Page 20
Adjust volume level
1 During play, press VOL +/- to increase/decrease the volume level.
Mute sound
1 During play, press MUTE to mute/unmute sound.
20
EN
Page 21
5 Product information
Note
Product information is subject to change without prior notice. •
Specifications
Amplifier
Rated Output Power2X15 W RMS
Signal to Noise Ratio85 dB
Aux-in Link0.6 V RMS 10 kohm
General information
AC power (power adaptor)For CE: OH-1065A1803500U2(EU)
Operation Power
Consumption
ECO Standby Power
Consumption
Dimensions
- Main Unit (W x H x D)169 x 420 x 108mm
Weight
- Main Unit2.22 kg
For USA: OH-1065A1803500U(UL)
Input: 100-240V~, 50/60Hz, 1. 5A;
Output: 18V
<40W
<1W
3.5A;
English
EN
21
Page 22
Bluetooth
Output power0 dBm (Class 2)
Frequency band2.4000 GHz - 2.4835 GHz ISM Band
Range6 meters(free space)
StandardBluetooth 2.0 specification
22
EN
Page 23
6 Troubleshooting
Warning
Never r emove the casing of this apparatus. •
To keep the warranty valid, never try to repair the system yourself.
If you encounter problems when using this apparatus, check the following
points before requesting service. If the problem remains unsolved, go to
the Philips web site (www.philips.com/welcome). When you contact Philips,
ensure that the apparatus is nearby and the model number and serial number
are available.
No power
Ensure that the AC power plug of the unit is connected properly. •
Ensure that there is power at the AC outlet. •
No sound
Adjust the volume. •
No response from the unit
Disconnect and reconnect the AC power plug, then turn on the unit •
again.
About Bluetooth device
Music playback is unavailable on the system even after successful Bluetooth
connection.
The device cannot be used with the system to play music. •
The audio quality is poor after connection with a Bluetooth-enabled
device.
The Bluetooth reception is poor. Move the device closer to the •
system or remove any obstacle between the device and the system.
Cannot connect with the system.
The device does not support the profiles required for the system. •
The Bluetooth function of the device is not enabled. Refer to the •
user manual of the device for how to enable the function.
English
EN
23
Page 24
The system is not in the pairing mode. •
The system is already connected with another Bluetooth-enabled •
device. Disconnect that device or all other connected devices and
then try again.
The paired device connects and disconnects constantly.
The Bluetooth reception is poor. Move the device closer to the •
system or remove any obstacle between the device and the system.
For some devices, the Bluetooth connection may be deactivated •
automatically as a power-saving feature. This does not indicate any