Philips DDL192LAFCB/97, DDL192LAGSB/97, DDL192LAGBB/97, DDL192LAGGB/97, DDL192LAFGB/97 User Manual
...
Contents
1 Important information 02
Security
Caution
Disposal of used
products and batteries
2 Install your EasyKey 03
Packaging list
Exploded views
Pre-installation instructions
Installation steps
3 Get to know your
EasyKey 08
Outside escutcheon
Inside escutcheon
4 How to set up your
EasyKey 09
-Modify Master PIN code
-User settings
-Delete a user
-System settings
-Extended functions
-System query
-Local query
-Bluetooth settings
5 How to use your
EasyKey 15
Unlock
Opening from outside
-With a PIN code
-With a ngerpr int
-With a card
Opening from ins ide
-With handle
-With Close button
Lock
-Auto/Manual modes
-Lock from outs ide
-Lock from inside
Deadlock from inside
Mechanical key opening
6 Other functions 18
Safe handle function
Restore to factor y sett ings
One-button mute function
Outside forced lock funct ion
7 Meanings & Use of
indicators 20
Door status indicator
Low battery indicator
Outside forced lock indicator
Mute mode indicator
Inside deadlock indicator
System lock indicator
[CLOSE] button indicator
8 Troubleshooting 22
Alarm types and alarm modes
How to apply an emergency power
How to replace batteries
1
1 Important information
2 Install your EasyKey
Security
◆Before using Philips EasyKey,
please read and understand all
instructions. Damage caused by noncompliance with the instructions
will not be covered by warranty.
◆Use only the manufacturerspecied accessories/components.
◆Use only the alkaline batter ies
the product is equipped w ith,
or use the same specification
type of alkaline batteries.
◆Do not forcibly disassemble
this product to avoid triggering an
alarm or damaging the product.
◆Do not scrape the ngerprint
sensor with sharp objects, otherwise
it may cause permanent damage.
◆Do not expose products to
environments where there is
water leakage or splashing.
◆Do not expose the product to
corrosive substances to prevent
damaging the protective cover.
◆Do not hang objects on the
handle, in case it might aect
the normal use of the lock.
◆Pleae clean the product
with a soft cloth.
◆Do not remove the battery during
sett ing up and operat ing.
◆Please let a professional technician
to install the door lock and follow the
installation guidelines provided.Do not
disassemble the lock by yourself. Keep the
relevant sealed stickers properly. Do not
easily disclose the password information.
◆Please modify the default
master PIN code immediately after
installation and conguration, and
keep the mechanical key properly.
◆Please replace all the batteries
immediately if there is a low
battery alarm. Please make sure
to correctly match the poles (+/-)
when installing the batteries.
Caution
◆Do not place the battery near
a re to avoid an explosion.
◆Do not use any emergency power
supply that does not meet the safety
requirements to power up the product.
◆Do not connect the 2 poles of the
batteries w ith met als to avoid short
circuit which may lead to an explosion.
◆Please make sure any component
replacement is executed by Philips,
Philips authorized service center
or professional technicians.
◆Do not use accessories or parts
that have been produced by other
manufacturers or have not been
specically recommended by
Philips. Use of such accessories and
parts may void your warranty.
Disposal of used products
and batteries
◆You can have your locks reclaimed at
Philips authorized service centers. You
will receive corresponding compensation
if your products meet our conditions.
◆Please learn by yourself the local
electronic product classication
and collection system.
◆Please abide by local regulations
and do not mix used products
with ordinary domestic waste.
◆Proper disposal of used products can
help to avoid potential negative impacts
on the env ironment and human health.
◆This product contains batteries
which can not be disposed of
together with domestic waste.
◆Please learn the local regulations
concerning battery classication
and collection by yourself. Proper
disposal of used batteries can
help to avoid negative impacts on
environment and human health.
Packaging list
This packaging list is for reference only. Please refer to the actual packaging
contents.
①Outside
escutcheon (including
silicone pad)
⑤Mounting plate ⑥User manual ⑦Quick start guide ⑧Warranty
EasyKey易锁
合格证
⑨Certicate
of conformity
⑬Installation kit ⑭Cleaning Pad
②Inside escutcheon
(including
silicone pad)
EasyKey易锁
User Manual
③Drilling template ④Mortise
EasyKey易锁
Quick Start
Guide
⑩Smart door card x2 ⑪Mechanical
key x2
Striker
EasyKey易锁
Warranty
Card
card
⑫Batteries
2 3
Exploded Views
Pre-installation instructions
Step 1 | Check the door opening direction
This product can be installed on doors of 4 opening directions:
left-out pull, right-in push, right-out pull and left-in push.
Left-handle open Right-handle open
Indoor Indoor
1. Battery cover (x1)
2. M6 chamfer head
screw (x1)
3. Inside escutcheon
component (x1)
4. Square shaft (x2)
5. M5 chamfer head
screw (x4)
6. Mount ing plate (x1)
7. Mortise (x1)
8. M6 screw tube (x1)
9. Outside escutcheon
(x1)
10. Rubber plug (x1)
11. M6 x 18 chamfer
head screw (x1)
12. M5 screw tube (x4)
Left-in
Outdoor
Indoor Indoor
Outdoor Outdoor
push
Leftout pull
Outdoor
Step 2 | How to switch between push and pull
Please x the screws in proper locations according to the door opening
direction.
Right-in push
Direction of
square shaft
driving block
Inside escutcheon
Screw
Right pull
Left push
Right push
Left pul l
Screw
Screw
Right-out pull
Direction of
square shaft
driving block
Inside escutcheon
Screw
Right pull
Attention
1.Use proper install atio n kit acco rding to t he door thickness.
2.The def ault installation k it is app licable to door s of 38-6 0mm thickness. If the thickness of your
door is n ot with in this ra nge, ple ase cont act us .
Left push
Right push
Left pul l
Screw
Screw
Left-in push
Right pull
Left push
Right push
Left pul l
Left-out pull
Right pull
Left push
Right push
Left pul l
Direction of
square shaft
driving block
Inside escutcheon
Screw
Direction of
square shaft
driving block
Inside escutcheon
Screw
Ri ghtin push
Ri ghtout pull
4 5
Installation steps
The following installation steps apply to right-open doors. For left-open doors,
please read the chapter [Pre-installat ion instruct ions] carefully and make
needed adjustments.
Use the drilling
1
template to drill
the needed holes
on the door and
mount the mortise
into the door.
Tighten the 4
2
anchor screws
on the mortise.
Install the connecting screw
3
tube and anchor screw tube
on the outside escutcheon.
Place the square shaft and
compressed spring into the
hole of the handle.
M6 screw tube
Install the compressed spring
6
and square shaf t into the inside
escutcheon accordingly.
Insert the connection wire of the
7
outside escutcheon and the motor
wire into the corresponding holes on
the inside escutcheon,
then align the square
shaft on the inside
escutcheon with the
rotar y hole on the
mortise and insert
it to make sure the
inside escutcheon
is kept close to the
inside of the door.
Attention
Please make sure
the mai n dead bolt
is retracted during
installation.
Pass the cable through the hole
on the door. The square shaft
4
needs to be inserted into the
rotar y hole on the mort ise, so
that the outer escutcheon stays
close to the outside door.
Attention
Select a square shaft and connecting
screw tube wit h appropriate length .
Tighten the mount ing plate
with the 4 M5 chamfer
5
head screws against the
inside of the door.
M5 scre w tube
Tighten the 2
8
M6 chamfer
head screws.
Put in the batter ies,
close the battery
cover and put in the
9
rubber plug. Then x
the str iker to nish
the installation.
Attention
Afte r xing the
str iker, plea se
test if t he door
can be o pened
and clo sed
smoothly.
Attention
Please hide th e extra
conne cting wires into the
door holes.
Please check if all
components are
connected properly,
10
such as the inside
and outside pushpull handle, the safe
handle switch and
the mechanical key.
6 7
Loading...