Contents
1 Important information 02
Security
Caution
Disposal of used
products and batteries
2 Install your EasyKey 03
Packaging list
Exploded views
Pre-installation instructions
Installation steps
3 Get to know your
EasyKey 09
Outside escutcheon
Inside escutcheon
4 How to set up your
EasyKey 10
-Pre-setup instructions
-Modify Master PIN code
-User settings
-Delete a user
-System settings
-Extended functions
-System query
5 How to use your
EasyKey 16
Unlock
Opening from outside the door
-With a PIN code
-With a ngerpr int
-With a card
Opening from inside the door
-With handle
-With Close button
Lock
-Auto/Manual modes
-Lock from outs ide the door
-Lock from inside the door
Deadlock from inside
Mechanical key opening
6 Other functions 19
Safe handle function
Restore to factor y sett ings
One-button mute function
Outside forced lock funct ion
Auto-sensing and auto wake-up
function
7 Use of the
indicator lights 21
Door status indicator light
Low battery indicator light
Outside forced lock indicator light
Mute mode indicator light
Inside deadlock indicator light
System lock indicator light
[Close] button indicator light
8 Troubleshooting 23
Alarm types and alarm modes
How to apply an emergency power
How to replace batteries
1
1 Important information
2 Install your EasyKey
Security
◆Before using Philips EasyKey,
please read and understand all
instructions. Damage caused by noncompliance with the instructions
will not be covered by warranty.
◆Use only the manufacturerspecied accessories/components.
◆Use only the alkaline batter ies
the product is equipped w ith.
◆Do not forcibly disassemble
this product to avoid triggering an
alarm or damaging the product.
◆Do not scrape the ngerprint
collector with sharp objects, otherwise
it may cause permanent damage.
◆Do not expose products to
environments where there is
water leakage or splashing.
◆Do not expose the product to
corrosive substances so a s not to
damage the protective cover.
◆Do not hang objects on the handle so
as not to aect the normal use of the lock.
◆Pleae clean the product
with a soft cloth.
◆Do not remove the battery during
sett ing up and operat ing.
◆Please let a professional technician
to install the door lock and follow the
installation guidelines provided by
our company. Do not disassemble the
door lock by yourself. Keep the relevant
seal signs properly. Do not easily
disclose the password information.
◆Please modify the default master
PIN code immediately after installation
and conguration and please keep
the mechanical key properly.
◆Please replace all the batteries
immediately if there is a low bat tery
alarm. Please make sure the
batteries are installed correctly.
Caution
◆Do not place the battery near
a re to avoid an explosion.
◆Do not use any emergency power
supply that does not meet the safety
requirements to power the product.
◆Do not connect the 2 poles of the
batteries w ith met als to avoid short
circuit which may lead to an explosion.
◆Please make sure any component
replacement is executed by Philips,
Philips authorized service center
or professional technicians.
◆Do not use accessories or parts
that have been produced by other
manufacturers or have not been
specically recommended by
Philips. Use of such accessories and
parts may void your warranty.
Disposal of used products
and batteries
◆You can have your locks reclaimed at
Philips authorized service centers. You
will receive corresponding compensation
if your products meet our conditions.
◆Please learn by yourself the local
electronic product classication
and collection system.
◆Please abide by local regulations
and do not mix used products
with ordinary domestic waste.
◆Proper disposal of used products can
help to avoid potential negative impacts
on the env ironment and human health.
◆This product contains batteries
which can not be disposed of
together with domestic waste.
◆Please learn by yourself the local
regulations concerning battery
classication and collection. Proper
disposal of used batteries can
help to avoid negative impacts on
environment and human health.
Packaging list
This packaging list is for reference only. Please refer to the actual packaging
contents.
①Outside
escutcheon (including
silicone pad)
⑤Mounting plate
EasyKey易锁
合格证
⑨Certicate
⑬ Installation kit
②Inside escutcheon
(including
silicone pad)
EasyKey易锁
User Manual
⑥User manual
⑩Smart door card x2
⑭Scouring pad
③Drilling template
EasyKey易锁
Quick Start
Guide
⑦Quick start guide
⑪Mechanical
key x2
Striker
④Mortise
EasyKey易锁
Warranty
Card
⑧Warranty
card
⑫Batteries
2 3
Exploded Views
Pre-installation instructions
Step 1 | Check the door opening direction
1 2 3 4 5 6 7 8 9 10
11 12 13 14
This product can be installed on doors of 4 types of opening directions:
left-out pull, right-in push, right-out pull and left-in push.
Left-handle open
Indoor Indoor
Left-in
Outdoor
push
Indoor Indoor
Leftout pull
Outdoor Outdoor
Right-handle open
Outdoor
Ri ghtin push
Ri ghtout pull
Step 2 | How to switch between push and pull
Please x the screws in proper locations according to the door opening
direction.
Right-in push
Outside escutcheon
Right pull
Right push
Left push
Left pul l
pull
push
Inside escutcheon
Right push
Right pull
Left pul l
Left push
push
pull
Screw
Outside escutcheon
Right pull
Left push
Left-in push
Right push
Left pul l
push
pull
Inside escutcheon
Right pull
Right push
Left push
Left pul l
push
pull
Screw
1. Battery cover (x1)
6. M5 chamfer
11. Rubber plug (x1)
Screw
Screw Screw Screw
head screw (x4)
2. M6 chamfer
head screw (x1)
3. Inside escutcheon
component (x1)
4. Compressed
spr ing (x2)
5. Square shaft (x2)
7. Mounting plate (x1)
8. Mortise (x1)
9.M6 screw tube (x1)
10. Outside
escutcheon
component (x1)
12.M6 x 18 chamfer
head screw (x1)
13. M5 screw tube (x4)
14. Cylinder key
tailpiece (x1)
Right-out pull
Outside escutcheon
Right push
Right pull
Left pul l
Left push
pull
push
Inside escutcheon
Right pull
Left push
pull
Right push
Left pul l
push
Outside escutcheon
Right pull
Left push
Left-out pull
Right push
Left pul l
pull
push
Inside escutcheon
Right pull
Left push
Screw Screw Screw Screw
pull
Right push
Left pul l
push
4 5
Step 3 | Choose the directional screw
Installation steps
Change the direction of the directional screw.
Double
latch bolt
Directional
screw
Directional
screw
◆Adjust the direct ion of the
directional screw according
to the door opening direction
(the directional screw must be
mounted on the inside of the door,
namely the inside escutcheon).
Attention
1.Use proper installation kit according to the door thickness.
2.The default installation kit is applicable to doors of 38-60 mm thickness.
If the thickness of your door is not within this range, please contact us.
The following installation steps apply to left-open doors. For right-open doors,
please read the chapter [Pre-installat ion instruct ions] carefully and make
needed adjustments.
Use the drilling
1
template to drill
the needed holes
on the door and
mount the mortise
into the door.
Pass the connection w ire
4
through the top hole. Meanwhile,
align the cylinder key tailpiece
Tighten the 4
2
anchor screws
3
on the mortise.
M6 screw tube
Attention Attention
Please make sure
the mai n dead bolt
is retracted during
installation.
Accord ing to the d oor thickness, you
may need to cut the c ylinder key
tailpiece sho rter. Ple ase use a ppropriate
lengths of squa re shaf t, connecti ng
screw tube and anchor scr ew tube.
Tighten the mount ing plate with
5
the 4 M5 chamfer head screws
against the inside of the door.
Install the connecting screw
tube and anchor screw tube
on the outside escutcheon.
Place the square shaft and
compressed spring into
the hole of the handle.
Press the thicker end of
the compressed spring
towards the handle
Cylinder key tailpiece
and square shaf t with the 2
rotar y holes on the mortise,
and insert them to make sure
the outside escutcheon is kept
close to the outside of the door.
M5 screw tube
6 7
Loading...