Philips DDL171LKCS0/97, DDL171LKCG0/97, DDL171LKCC0/97, DDL171LKAG0/97, DDL171LKAS0/97 User Manual
...
Contents
1 Important information 02
Safety
Caution
Disposal of used products
and batteries
2 EasyKey Installation 03
Packing List
Exploded views
Pre-installation instructions
Installation steps
3 Get to know your
EasyKey 09
Outside Escutcheon
Inside Escutcheon
4 How to set up your
EasyKey 10
Pre-setup instructions
5 How to use your EasyKey 16
Unlock
Unlock from Outside
-With a PIN code
-With a ngerprint
-With a Key Tag
Unlock from Ins ide
-With the Handle
Lock
Lock from Outside
Lock from Inside
Inside Deadlock
Mechanical key opening
6 Other functions 18
Safe handle function
Restore to default sett ings
Mute Mode
7 Meanings of the Indicators 20
Door status indicator
Low battery voltage indicator
Mute mode indicator
System lock indicator
-Modify Master PIN code
-User settings
-Delete a User Record
-System settings
-Extended functions
-System query
-Local Query
8 Troubleshooting 22
Alarm types and alarm modes
How to apply an
emergency power supply
How to replace batteries
1
1 Important Information
Safety
◆Before using Philips EasyKey, please
read and understand all instruct ions.
Damage caused by non-compliance with
the instructions will not be covered by
warranty.
◆Use only the manufacturer-specied
accessories/components.
◆Use only the alkaline batteries the
product is equipped with, or use the
same specification type of alkaline
batteries.
◆Do not forcibly disassemble this product
to avoid tr iggering an alarm or damaging
the product.
◆Do not scrape the ngerpr int sensor
with sharp objects, otherwise it may cause
permanent damage.
◆Do not expos e product s to enviro nments
where there is water leakage or spla shing.
◆Do not expose the product to corrosive
substances to prevent damaging the
protective cover.
◆Do not hang objects on the handle, in
case it might aect the normal use of the
lock.
◆Pleae clean t he product w ith a soft cloth .
◆Do not remove the battery during
sett ing up and operating.
◆Please let a professional technician
to install the door lock and follow the
installation guidelines provided.Do not
disassemble the lock by yourself. Keep the
relevant sealed stickers properly. Do not
easily disclose the password informat ion.
◆Please modify the default master PIN
code immediately after nishing installing
and debugging, and keep the mechanical
key properly.
◆Please replace all the batteries
immediately if there is a low battery alarm.
Please make sure to correctly match the
poles (+/-) when installing the bat ter ies.
Caution
◆Do not place the battery near re
sources to avoid explosion.
◆Do not use any emergency power
supply that does not meet the safety
requirement s to power up the product.
◆Do not connect the 2 poles of the
batteries with metals to avoid short circuit
which may lead to an explosion.
◆Please make sure any component
replacement is executed by Philips, Philips
authorized service center or professional
technicians.
◆Do not use acces sories or p arts tha t have
been produced by other manufacturers or
have not been spec ically recommended
by Philips. The use of such accessor ies and
parts may void your warrant y.
Disposal of used products and
batteries
◆You can have your locks reclaimed at
Philips authorized service centers. You will
receive corresponding compensation if
your products meet our conditions.
◆Please familiarize yourself with the local
electronic product collection system.
◆Please follow local regul ations and do
not discard used products into ordinar y
household waste.
◆Proper disposal of used products can
help to avoid potent ial negative impacts
on the env ironment and human health.
◆Batter ies must not be disposed of with
ordinary household waste.
◆Please familiarize yourself with the local
regulations on batteries classication
recycling. Disposing of batter ies properly
can help avoid a negative impac t on the
environment and human health.
2
2 EasyKey Installation
Packing List
This packing list is for reference only. Please refer to the actual pack ing
contents.
①Outside escutcheon
(including silicone pad)
⑤Mounting plate
EasyKey易锁
合格证
⑨Certicate of
Conformity
②Inside escutcheon
(including silicone pad)
EasyKey易锁
User Manual
⑥User manual
⑩Key Tag X2
③Drilling template
EasyKey易锁
Quick Start
Guide
⑦Quick start guide
⑪Mechanical key x2
④Mortise
EasyKey易锁
Warranty
Card
⑧Warranty card
⑫Batteries
⑬ Installation kit
⑭Cleaning Pad
Str iker
3
Exploded views
101112131415
123
45
7
6
8
16 17
1. Outside
escutcheon (x1)
2. Outside escutcheon
silicone pad (x1)
3. Connecting
screw (x2)
4. Square shaft
compressed spring (x2)
5. Square shaft (x2)
6. Cotter pin (x2)
4
7. 7.Mechanical key
slide tailpiece (x1)
8. Mortise (x1)
9. Mort ise anchor
screw (x4)
10. Mounting plate (x1)
11. Mounting plate
anchor screw (x2)
12. Inside escutcheon
silicone pad (x1)
9
13. Inside escutcheon (x1)
14. Inside escutcheon
anchor screw (x4)
15. Battery cover (x1)
16. Inside escutcheon
lower cover (x1)
17. Rotary knob
tailpiece (x1)
Pre-installation instructions
Step 1 | Conrm the door opening direction
This product can install on 4 directions: left-out pull,right-in push, left-in
push and right-out pull.
Left-handle open Right-handle open
Indoor Indoor
Left-in
Outdoor Outdoor
Indoor Indoor
Outdoor Outdoor
push
Leftout pull
Step 2 | Handle Direction Reversing
Ri ghtin push
Ri ghtout pull
Lock
screw
back
Remove the two
1
crossed countersunk
screws from the
outside escutcheon.
Directly rotate the
2
handle to 180°.
Lock th e two cro ssed
3
countersunk screws
back.
5
Step 3 | Latch Bolt Direction Reversing
You can change the latch bolt direct ion according to dierent door opening
directions: outward bevel for inward opening and inward bevel for out ward
opening.
Latch bolt reversing tailpiece
Latch bolt
Attention
1. Choose di erent i nstalla tio n kit a s per d iere nt door thick ness range.
2. The default inst allatio n kit a ppli es to door thickness of 38 to 60 m m. If the door thickn ess is not
within this range, plea se contact us.
Directional screw
1. Push the rever sing tailpiece upwards to the top.
2. Press the latch bolt into the mort ise and rotate it
180 degrees. Then pull it out.
3. Push the tailpiece downwa rds to the bottom.
4. Change the direction of the screws as needed
(The direc tional screws must be xed on the inside
of the door, namely towards the inner unit of the
lock).
Installation steps
The following installat ion steps apply to right opening doors. For left
opening type, please read the [Pre-installation Instructions] carefully and
complete those necessary reversing operations.
Use the drilling template to drill
1
the needed holes on the door
and mount the mortise into the
door.
6
Hook the upper and bottom
2
poles when the mort ise is
inserted(This step is not required
when installing on the wooden
door).
Loading...