Contents
1 Important information 02
Safety
Caution
Disposal of used
products and batteries
2 EasyKey Installation 03
Packing list
Exploded views
Pre-installation instructions
Installation steps
3 Get to know your
EasyKey 08
Outside escutcheon
Inside escutcheon
4 How to set up your
EasyKey 09
-Pre-setup instructions
-Modify master PIN code
-User settings
-Delete a user record
-System settings
-Extended functions
-System query
-Local quer y
5 How to use your
EasyKey 15
Unlock
Unlock from outside
-With a PIN code
-With a ngerprint
-With a card
Unlock from inside
-With handle
-With Close button
Lock
-Auto/Manual modes
-Lock from out side
-Lock from inside
Inside deadlock
Mechanical key opening
6 Other functions 18
Restore to default sett ings
Mute function
Outside forced lock
7 The use & meanings of the
indicators 19
Lock status indicator
Low battery voltage indicator
Outside forced lock indicator
Mute mode indicator
Inside deadlock indicator
System lock indicator
[CLOSE] button indicator
8 Troubleshooting 21
Alarm types and alarm modes
How to use an emergency power
How to replace batteries
1
1 Important information
2 EasyKey Installation
Safety
◆Before using Philips EasyKey, please
read and understand all instruct ions.
Damage caused by non-compliance with
the instructions will not be covered by
warranty.
◆Use only the manufacturer-specied
accessories/components.
◆Use only the alkaline batteries the
product is equipped with, or use the
same specification type of alkaline
batteries.
◆Do not forcibly disassemble this product
to avoid tr iggering an alarm or damaging
the product.
◆Do not scrape the ngerpr int sensor
with sharp objects, otherwise it may cause
permanent damage.
◆Do not expos e product s to enviro nments
where there is water leakage or spla shing.
◆Do not expose the product to corrosive
substances to prevent damaging the
protective cover.
◆Do not hang objects on the handle, in
case it might aect the normal use of the
lock.
◆Pleae clean t he product w ith a soft cloth .
◆Do not remove the battery during
sett ing up and operating.
◆Please let a professional technician
to install the door lock and follow the
installation guidelines provided.Do not
disassemble the lock by yourself. Keep the
relevant sealed stickers properly. Do not
easily disclose the password informat ion.
◆Please modify the default master PIN
code immediately after nishing installing
and debugging, and keep the mechanical
key properly.
◆Please replace all the batteries
immediately if there is a low battery alarm.
Please make sure to correctly match the
poles (+/-) when installing the bat ter ies.
Caution
◆Do not place the battery near re
sources to avoid explosion.
◆Do not use any emergency power
supply that does not meet the safety
requirement s to power up the product.
◆Do not connect the 2 poles of the
batteries with metals to avoid shor t circuit
which may lead to an explosion.
◆Please make sure any component
replacement is executed by Philips, Philips
authorized service center or professional
technicians.
◆Do not use acces sories or p arts tha t have
been produced by other manufacturers or
have not been spec ically recommended
by Philips. The use of such accessor ies and
parts may void your warrant y.
Disposal of used products and
batteries
◆You can have your locks reclaimed at
Philips authorized service centers. You will
receive corresponding compensation if
your products meet our conditions.
◆Please familiarize yourself with the local
electronic product collection system.
◆Please follow local regulations and do
not discard used products into ordinar y
household waste.
◆Proper disposal of used products can
help to avoid potent ial negative impacts
on the env ironment and human health.
◆Batter ies must not be disposed of with
ordinary household waste.
◆Please familiarize yourself with the local
regulations on batteries classicat ion
recycling. Disposing of batter ies properly
can help avoid a negative impact on the
environment and human health.
Packing List
This packing list is for reference only. Please refer to the actual packing
contents.
①Outside
escutcheon (including
silicone pad)
⑤Mounting plate ⑥User manual ⑦Quick start guide ⑧Warranty
EasyKey易锁
合格证
⑨Certicate
of Conformity
⑬ Installation kit ⑭Cleaning Pad
②Inside escutcheon
(including
silicone pad)
EasyKey易锁
User Manual
③Drilling template ④Mortise
EasyKey易锁
Quick Start
Guide
⑩Key Tag X2 ⑪Mechanical
key x2
Striker
EasyKey易锁
Warranty
Card
card
⑫Batteries
2 3
Exploded Views
Pre-installation instructions
Step 1 | Conrm the door opening direction
This product can be installed on doors of 4 directions: left-out pull, right-in push,
right-out pull and lef t-in push.
Left-handle open Right-handle open
Indoor Indoor
1. Batter y cover (x1)
2.Inside escutcheon
anchor screw (x6)
3.Inside escutcheon
component (x1)
4.Mount ing pl ate
anchor screw (x4)
5. Mount ing plate (x1)
6. Inside escutcheon
silicone pad (x1)
7. Square shaft
compressed spring (x2)
8. Square shaft (x2)
9. Mortise (x1)
10. Connect ing screw
tube (x4)
11. Grub screw (x4)
12.Outside escutcheon
silicone pad (x1)
13.Outside escutcheon
component (x1)
Left-in
Outdoor
Indoor Indoor
Outdoor Outdoor
push
Leftout pull
Outdoor
Ri ghtin push
Ri ghtout pull
Installation steps
The following inst all ation steps apply to right-open doors. For left-open door s,
please read the chapter [Pre-installation instructions] carefully and make needed
adjustments.
Install the M5 grub screws and screw
1
tubes into the outside escutcheon.
M5 grub
screw
Attention
Please use proper s quar e shaf t, con nec ting screw
tube and anchor screw tube s accor ding to your
door's thickness.
Use the drilling template to drill
2
the needed holes in the door. Pass
the connect ing cable of the outside
escutcheon through the door hole.
4 5
Put the mort ise in the door and
3
align it with the screw tubes in the
outside escutcheon.
Tighten the anchor screws in the
4
mortise.
Inser t the connecting cables of
7
outside escutcheon and motor into
the corresponding sockets in the
inside escutcheon. Align the square
shaft of the inside escutcheon
to the rot ary hole in the mor tise
and insert it, then make the inside
escutcheon close to the inside of
the door.
4 M4 screws
on the front
2 M4 grub
screws in
ank
Keep the multicolor r ibbon under
8
the bat ter ies while put ting the srt
set of bat ter y into the cabin, which
could make battery removal easier
for next battery replacement.
After all 8 batteries are in pl ace,
install the battery cover and the
striker.
Put the mounting plate against the
5
inside of the door and x it with the
four M5 chamber head screws.
Put the compressed spring and
6
then the square shaf t in the inside
escutcheon accordingly.
Bigge r end of t he comp ressed
spring face to the ha ndle
Socket f or out side
escutcheon
connecting cable
Socket f or mor tise
connecting cable
After all the above is nished, please check if every component is well connec ted
9
and if the lock works normally.
Fingerprint
sensor
Keypad
Card reader
Mortise
Close button
Rotary knob
Reset button
A/M sw itch
6 7
Loading...