Philips SNP6000, DB100486 User Manual

Register your product and get support at

www.philips.com/welcome

EN User manual

Presenter

SNP6000

1

a

b
c

d

e

23

4

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the
following measures:
to confi rm successful numbering

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifi cations not expressly approved
by the party responsible for compliance could void the user’s
authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.

This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT

Wavelength : 645 - 660nm
Maximum Power < 1mW
IEC 60825-1:1993 + A1:1997 + A2:2001
EN 60825-1:1994 + A2:2001 + A1:2002

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED

BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE

INSTRUCTIONS

Complies with
IDA Standards

DB100486

EN

1 Overview of the product (Fig. 1)

a LED indicator
b Control buttons;

Button Presenter Air mouse

c Mode switch ( : Presenter; : Air mouse)
d Nano Dongle
e Battery compartment

Play/Stop Click to open the fi le
Blank screen No function
Previous slide Left mouse click
Next slide Right mouse click
Laser pointer Laser pointer

2 Switch on the product

C Caution

Keep the Nano Dongle out of reach of children. •

1 Open the battery compartment.
2 Insert 2 AAA batteries with correct polarity (+/-) as indicated (Fig. 2).
3 Take out the Nano Dongle (Fig. 3).
4 Close the battery compartment.
5 To use the product as a presenter, switch to .

To use the product as an air mouse, switch to • .

3 Get started

1 Ensure that your notebook is switched on and active.
2 Ensure that your fl oating presenter is switched on.
3 Plug the Nano Dongle into a USB host on your notebook.

Auto-connection starts. »
The LED blinks upon every successful communication between »
the fl oating presenter and the Nano Dongle.

E Tip

Upon the fi rst inst allation on Mac, • Keyboard Set Assistant may appear
and prompt that the keyboard cannot be identifi ed. Click Continue to
fi nish the inst allation, and then the fl oating presenter works accor dingly.

•

After use, insert the Nano Dongle into your fl oating presenter for
stor age (Fig. 4).

4 Troubleshooting

Problem Solution
No transmission. Ensure that you use the product within

Light on your product
blinks 3 times.

Light on your product
does not blink.

The mouse does not work. Ensure that you switch on the mouse

effective range.
Replace batteries on the product.

1. Ensure that the product is switched on.

2. Replace batteries on the product.

mode.

5 Disposal of your old product

Your product is designed and manufactured with high quality materials
and components, which can be recycled and reused.
When this crossed-out wheeled bin symbol is attached to a product it
means that the product is covered by the European Directive 2002/96/EC.
Please inform yourself about the local separate collection system for
electrical and electronic products.
Please act according to your local rules and do not dispose of your old
products with your normal household waste. Correct disposal of your
old product helps to prevent potential negative consequences for the
environment and human health.

Your product contains batteries covered by the European Directive
2006/66/EC, which cannot be disposed with normal household
waste. Please inform yourself about the local rules on separate collection
of batteries because correct disposal helps to prevent negative
consequences for the environmental and human health.

© 2010 Koninklijke Philips Electronics N.V.
All rights reserved.

Specifi cations are subject to change
without notice.Trademarks are the
property of Koninklijke Philips Electronics
N.V. or their respective owners.

UM_V3.1