Important safety instructions
Overview
1
Warning
• The Electrical network is classified as hazardous. The
only way to power down the charger is to unplug the
power supply from the electrical outlet. Ensure that the
electrical outlet is always easily accessible.
• Refer to safety information before using the product.
• This product complies with European R&TTE
directive 1999/5/EC
• Use only the power supply listed in the user
instructions.
D205
D200
• Use only the batteries listed in the user instructions.
• Do not allow the product to come into contact with
liquids.
• Risk of explosion if battery is replaced by an incorrect
type.
• Dispose of used batteries according to the
instrucions.
• When the handset rings or when the handsfree is
activated, keep the handset away from your ear to
avoid hearing damage.
WK1248
05_EN_V1.0
QSG_D200-205
Short user manual
0168
www.philips.com/welcome
Register your product and get support at
In call
Enter the option
menu
Adjust the volume
End calls
Turn the speaker
on/off
Mute/unmute the
microphone
Enter a pause
In menu
Conrm / Enter
the option menu /
Select
Cancel
Up / down
Exit menu
© 2013 Koninklijke Philips Electronics N.V.
All rights reserved.
N.V. or their respective owners.
property of Koninklijke Philips Electronics
the copyright owner. Trademarks are the
prohibited without the written consent of
Reproduction in whole or in part is
Directive 2002/96/EC.
the product is covered by the European
is attached to a product it means that
When this crossed-out wheeled bin symbol
documentation online.
For information, refer to the extended user
www.philips.com/support
Display icons
It displays the connection between the handset
and the base. The more the bars are shown, the
better the connection is.
It remains steadily on when browsing incoming
calls in the call log.
It indicates an outgoing call in the redial list.
It ashes when there is a new missed call or
when browsing new missed calls. It remains
steadily on when browsing the missed calls in
call log that are already read.
It ashes when receiving incoming call. It remains
steadily on during a call.
The speaker is on.
The ringer is off.
(for D205 only) Answering machine: it ashes
when there is a new message. It remains steadily
on when the telephone answering machine is
turned on.
Voice messages indicator: ashes for new
messages, is steady for reviewed messages.
* This is network dependent
It displays when you scroll up/down a list or
increase and decrease the volume.
There are more digits on the right. Press to
read.
ECO+
The ECO+ mode is activated.
Standby
Access the main
menu
Phonebook
Call log
Make and receive
calls
Make intercom call
Lock/unlock the
keypad
Make and receive
calls through the
speaker
In text input
Delete text
Enter a space
Switch upper/lower
case
Display icons
Earpiece
Speaker
(back of the
handset)
Microphone
D205D200
Find
handset
Connect
2
1 2 3
Loudspeaker
(the rear side)
/
/
Multi-handset version
only.
Get started
3
4
Enjoy
Frequently
Insert batteries
Congure your phone
1 When using your phone for the rst time, you see
a welcome message (country dependent).
2 Set the countr y and language if prompted.
3 Set the date and time.
• If the time is in 12-hour format, press / key
to select [am] or [pm] (country dependent).
Charge your phone
Charge 8 hours
> 70%
40% - 70%
Flashing: low battery
Scrolling: charging in progress
10% - 40%
< 10%
Phonebook
Add record
1 Press .
2 Select [Phonebook] > [Add new].
3 Follow on-screen instructions.
Call from the phonebook
1 Press .
2 Select a record and press .
Direct access memory
You have 2 direct access memories (Keys 1 and 2).
To dial the saved phone number automatically, press
and hold on the keys in standby mode.
Depending on your country, keys 1 and 2 are preset
to [1_voicemail] (voice mail number) and [2_info
svc] (information service number) of your network
operator respectively (network dependent).
Call log
Call from the call log
1 Press .
2 Select a record and press .
Add record
1 Press > > [Save number].
2 Follow on-screen instructions.
Delete record
1 Press > > [Delete].
2 Follow on-screen instructions.
Redial list
Call from the redial list
1 Press .
2 Select a record and press .
Add record
1 Press > > [Save number].
2 Follow on-screen instructions.
Delete record
1 Press > > [Delete].
2 Follow on-screen instructions.
Record an announcement
(for D205 only)
1 Press .
2 Select [Answ. Machine] > [Announcement].
3 Follow on-screen instructions.
Register additional handsets
You can register additional handsets to the base
station.
1 Press .
2 Select [Services] > [Register], then press
to conrm.
3 Press and hold on the base station for 5
seconds.
4 Enter the system PIN/Passcode (0000).
5 Press to conrm the PIN/Passcode.
»
Registration is completed in less than 2 minutes.
Restore default settings
You can reset your phone settings to the original
factory settings.
1 Press .
2 Select [Services] > [Reset], then press to
conrm.
3 Follow on-screen instructions.
Note
• You may recall the original PIN/Passcode by
following this procedure.
Technical data
Battery
• Philips: 2 x AAA NiMH 1.2 V Rechargeable
Use only the supplied batteries.
Adapter
Phonebook with 50 entries
Call log with 20 entries
Talk time: 16 hours
Standby time: 180 hours
• You can install a DSL (digital subscriber line) lter
• You can nd the Declaration of Conformity on
550 mAh batteries
Base and charger:
Philips: MN-A102-U130 S003IB0600040
Input: 100-240 V
50/60 Hz 0.2 A
Output: 6 V 400 mA 6 V 400 mA
Note
to prevent noise and caller ID problems caused by
the DSL interference.
www.p4c.philips.com.
100-240 V
50/60 Hz 0.15 A
asked questions
No signal bar is displayed on the screen.
• The handset is out of range. Move it closer to the
base station.
• If the handset displays [Unregistered], register
your handset.
If I fail to pair (register) the additional handsets to
the base station, what do I do?
Your base memor y is full. Access > [Services]
> [Unregister] to unregister the unused handsets
and try again.
I have chosen a wrong language which I cannot read,
what do I do?
1 Press to go back to the standby screen.
2 Press to access the main menu screen.
3 The following options will appear on the screen:
[Phone setup] > [Language]
[Réglages] > [Langue]
[Telefon-Setup] > [Sprache]
[Cong. telef.] > [Lingua]
4 Select it to access the language options.
5 Select your own language.
My handset is in searching status, what do I do?
• Make sure that the base station has power supply.
• Register the handset to the base station.
• Move the handset closer to the base station.
I cannot change the settings of my voice mail, what
do I do?
The voice mail service is managed by your service
provider but not the phone itself. Contact your
service provider to change the settings.
No display
• Make sure the batteries are charged.
• Make sure there are power and phone connections.
The handset on the charger does not charge.
• Make sure the batteries are inser ted correctly.
• Make sure the handset is placed properly on the
charger. The battery icon animates when charging.
• Make sure the docking tone setting is turned on.
When the handset is placed correctly on the
charger, you can hear a docking tone.
• The charging contacts are dir ty. Disconnect the power
supply rst and clean the contacts with a damp cloth.
• Purchase new ones with the same specications.
Bad audio (crackles, echo, etc.)
• The handset is nearly out of range. Move it closer
to the base station.
• The phone receives interference from the nearby
electrical appliances. Move the base station away
from them.
• The phone is at a location with thick walls. Move
the base away from them.
The handset does not ring.
Make sure the handset ringtone is turned on.
The caller ID does not display.
• The service is not activated. Check with your
service provider.
• The caller’s information is withheld or unavailable.
Loading...