Philips CSP620/51, CSP620, CSP6920 User Manual

Register your product and get support at

www.philips.com/welcome

CSP620 CSP6920

EN User manual

A

b

e

a

d

c

B

a b

c

d

Amplifier

Right White lined White lined

Right

Left

Black

Black

Left

CSP620
CSP6920

e

f g

C

English

1. Important

Safety

Read and understand all instructions before you use the apparatus. •
If damage is caused by failure to follow instructions, the warranty does
not apply.

Use only the supplied mounting hardware for a safe and secure •
installation.

Do not continuously use the speaker system beyond the peak power •
handling capacity.

Keep credit cards, watches, recorded tapes etc. with magnetic coding •
away from the speaker system to prevent damage caused by the
magnets in the speakers.

Clean the apparatus with soft, damp cloth. Never use substances such •
as alcohol, chemicals or household cleaners on the apparatus.

Notice

Environmental information

All unnecessary packaging has been omitted. We have tried to make
the packaging easy to separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused if
disassembled by a specialized company. Please observe the local regulations
regarding the disposal of packaging materials, exhausted batteries and old
equipment.

Any changes or modications made to this device that are not expressly

approved by Philips Consumer Lifestyle may void the user’s authority to
operate the equipment.

2009 © Koninklijke Philips Elec tronics N.V. All rights reserved.

Specicat ions are subj ect to change without noti ce. Trademarks are the proper ty of Konink lijke Philips

Elec tronics N.V. or their re spec tive ow ner s. Philips re ser ves the right to change products at any tim e
with out be ing obliged to adjust earlier sup plies accordingly.

2. Your car stereo speakers

Congratulations on your purchase, and welcome to Philips! To fully
benet from the support that Philips offers, register your product at
www.philips.com/welcome.

Introduction

With the speakers, you can enjoy high power music with vivid sound.

What’s in the box

Check and identify the contents of your package:

Speakers (x2)

a

Grille net + Frame (x2)

b

Speaker wire (x2)

c

Screw (x8)

d

Shrapnel (x8)

e

A

3. Installation

A depth of at least 46mm is required to mount the speaker. Measure the
depth of the area where you are to mount the speaker, and ensure that
the speaker does not obstruct any other components of the car.

Option 1: Mount on door (front or rear)

You can mount the speakers on the front/rear door of your car.

B

a

Note

Make sure that nothing obstructs around the mounting location of the door.

•

A hole for mounting may already be cut out of the inner panel of the door

•

(front or rear). In this case, you need to modify the board only.
Ensure that the speaker ter minals, frame or magnet do not interfere with any

•

inner parts, such as the window mechanism in the door (when you open or
close the window), etc. Also ensure that the speaker grille does not touch any

inner ttings, such as the window cranks, door handles, arm rests etc.

Turn off the car ignition key.

1

•

If the power is on, the click noise generated by the connection
may damage the speakers.

Cut out the mounting template from the packing box.

2

Paste the template on the location selected for mounting the

3

speaker.

b

Mark the cut-off hole and the 4 bolt holes.

4

Cut out the marked area and drill the bolt holes.

5

Remove the grille net.

6

Strip the speaker wires and connect them to the amplier.

7

•

Black wire: connect to “-“ (negative) terminal

•

Black (white lined): connect to “+“ (positive) terminal

Note

Match the “lef t”, “right”, “+” and “-” terminals correctly. Revised polarity may

•

degrade sound quality.

Two 4-ohm speakers, wired in stereo, present a 8 ohm load to each channel

•

of the amplier. Most two channel ampliers work well in this conguration.

However, if two 4-ohm speakers, wired in parallel to a bridged two -channel

amplier, present a 2-ohm mono load to the amplier. Most 2-channel ampliers
do not suppor t 2-ohm mono operation! Amplier damage may result!

d

c

e

Mount on the speaker as shown below.

8

Press and insert the edges of the grille net.

9

f

g

Tip

The speaker grille can be mounted without the grille net, if you like.

•

Option 2: Mount on rear tray

C

You can also mount the speakers into the surface of the rear tray.

Follow the steps in section “Option 1: Mount in door” to mount the
speakers into the rear tray:

4. Product information

Note

Product information is subject to change without prior notice. •

Model CSP620 CSP6920

Speaker type 16.5cm, 3-way triaxial

speaker

RMS power (Watts) 80W 80W

Peak music power (Watts) 400W 480W

Sensitivity (dB/W/m) 90dB 91dB

Frequency response (Hz) 35-32kHz 27-33kHz

Impedance (ohms) 4 ohms 4 ohms

Magnet mass (Oz) 8.6Oz 22Oz

Mounting depth (mm) 59mm 88.1 mm

16x24cm, 5-way coaxial
speaker

5. Troubleshooting

To keep the warranty valid, never try to repair the system yourself.

If you encounter problems when using this apparatus, go to the Philips
web site (www.philips.com/welcome). When you contact Philips, ensure
that the apparatus is nearby and the model number and serial number
are available.

© 2009 Koninklijke Philips Electro nics N.V.
All rig hts reserved.
CSP620_51_UM_V2.0