Page 1
Register your product and get support at
www.philips.com/welcome
CSP550
CSP650
CSP652
EN User manual
Page 2
1. Important
Safety
Read and understand all instructions before you use the apparatus. •
If damage is caused by failure to follow instructions, the warranty
does not apply.
Use only the supplied mounting hardware for a safe and secure •
installation.
Do not continuously use the speaker system beyond the peak power •
handling capacity.
Keep credit cards, watches, recorded tapes etc. with magnetic coding •
away from the speaker system to prevent damage caused by the
magnets in the speakers.
Clean the apparatus with sof t, damp cloth. Never use substances •
such as alcohol, chemicals or household cleaners on the apparatus.
Notice
Environmental information
All unnecessary packaging has been omitted. We have tried to make
the packaging easy to separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused
if disassembled by a specialized company. Please obser ve the local
regulations regarding the disposal of packaging materials, exhausted
batteries and old equipment.
Any changes or modications made to this device that are not expressly
approved by Philips Consumer Lifestyle may void the user’s authority to
operate the equipment.
2009 © Koninklijke Phili ps Elec tro nics N .V. All righ ts reserved.
Specicat ions are subject to change w ithout notice. Trad emar ks are the propert y of Koninklijke
Phili ps Elec tro nics N .V. or their r espective owners. Philips reserves t he right to cha nge produc ts at
any time with out be ing obl iged to adjust earl ier supplies accordingly.
Page 3
2. Your car stereo speakers
b
e
d
a
c
f
2-WAY CROSSOVER NETWORK
12dB/Oct.
WOOFER
INPUT
TWEETER
gh
jk
i
Congratulations on your purchase, and welcome to Philips! To fully
benet from the support that Philips offers, register your product at
www.philips.com/welcome.
Introduction
With the woofers and tweeters, you can enjoy high power music with
vivid sound.
What’s in the box
Check and identify the contents of your package:
a Woofer (x2)
b Grille assembly (x2)
c Tweeter (with wire) (x2)
d Network (x2)
e Speaker wire (x2)
f Angle adapter (x2)
g Fix frame (x2)
h
i Screw (x2)
j Screw nut (x2)
k Shrapnel (x16)
Mounting bracket (x4)
Page 4
3. Installation
A depth of at least 49mm is required to mount the woofer and a depth
of at least 19mm is required to mount the tweeter. Measure the depth
of the area where you are to mount the woofer/tweeter, and ensure that
the woofer/tweeter does not obstruct any other components of the car.
Note
Make sure that nothing obstructs around the mounting location of the door.
•
A hole for mounting may already be cut out of the inner panel of the door
•
(front or rear). In this case, you need to modify the board only.
Ensure that the speaker ter minals, fr ame or magnet do not interfere with any
•
inner parts, such as the window mechanism in the door (when you open or
close the window), etc. Also ensure that the speaker grille does not touch any
inner ttings, such as the window cranks, door handles, arm rests etc.
Mount the woofer
Option 1: Mount on door (front or rear)
You can mount the wooferss on the front/rear door of your car.
Page 5
Turn off the car ignition key.
1
•
If the power is on, the click noise generated by the connection
may damage the speakers.
Cut out the mounting template from the packing box and
2
paste it on the location selected for mounting the woofer.
Mark the cut-off hole and the 4 bolt holes.
3
Cut out the marked area and drill the bolt holes.
4
Remove the grille net.
5
Connect the woofers to the network or car audio (see ‘Connect
6
the woofer/tweeter to the network’).
Page 6
Mount on the speaker as shown below.
7
Press and inser t the edges of the grille net.
8
Tip
The speaker grille can be mounted without the grille
•
net, if you like.
Option 2: Mount on dashboard or
rear tray
You can also mount the woofers into the surface
of the dashboard or rear tray.
Follow the steps in section
“Option 1: Mount in door” to
mount the speakers into the
dashboard or rear tray.
Page 7
Mount the Tweeter
Option 1:
Flush mounting
Option 2:
Flush mounting
Option 3:
Surface mounting
Option 4:
Surface mounting
Option 5:
Angle mounting
Follow steps mentioned in “Mount the woofer” section to mount the
tweeters.
Page 8
Mount the network
2-WA
Y CROSSOVER NETWORK
12dB/Oct.
WOOFER
INPUT
TWEETER
Find a proper location to mount the networks.
1
Mount the networks onto the car with the supplied screws.
2
Connect the woofer/tweeter to the network
Note
Match the “lef t”, “right”, “+” and “-” terminals correctly. Revised polarity may
•
degrade sound quality.
Two 4-ohm speakers, wired in stereo, present a 4 ohm load to each channel
•
of the amplier. Most two channel ampliers work well in this conguration.
However, if two 4-ohm speakers, wired in parallel to a br idged two -channel
amplier, present a 2-ohm mono load to the amplier. Most 2-channel
ampliers do not suppor t 2-ohm mono operation! Amplier damage may
result!
Connect the woofers and the tweeters to the 2-way crossover
1
network rst, then connect the network to your amplier or
car audio directly.
Page 9
White lined
White lined
White lined
GSA_WGK
Amplifier
Network
Woofer
Tweeter
Amplifier
Midwoofer
Tweeter
WOOFERINPUT TWEETER
Black
Black
Black
component
speaker
16.5cm, 2-way
component
speaker
16.5cm, 2-way
component
speaker
4. Product information
Model CSP550 CSP650 CSP652
Speaker type 13cm, 2-way
RMS power (Watts) 40W 50W 60W
Peak music power (Watts) 210W 240W 300W
Sensitivity (dB/W/m) 90dB 90dB 91dB
Frequency response (Hz) 40 -35kHz 36-35kH z 34 -35kH z
Impedance (ohms) 4 ohms 4 ohms 4 ohms
Magnet mass (Oz) 11Oz 12.6O z 18.8Oz
Page 10
Note
Product information is subjec t to change without prior notice.
•
5. Troubleshooting
To keep the warranty valid, never try to repair the system yourself.
If you encounter problems when using this apparatus, go to the
Philips web site (www.philips.com/welcome). When you contact
Philips, ensure that the apparatus is nearby and the model number
and serial number are available.
Name of the Parts
Housing O O O O O O
Loudspeakers O O O O O O
PWBs X O O O O O
Accessories (Remote
control & cables)
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this par t is
below the limit requirement in SJ/T11363 - 2006.
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used
for this part is above the limit requirement in SJ/T11363 - 2006.
This logo refers to the period ( 10 years ) during which the toxic or hazardous substances or elements contained in electronic
information products will not leak or mutate so that the use of these [substances or elements] will not result in any severe
environmental pollution, any bodily injur y or damage to any assets.
© 2009 Koninklijke Philips Electronics N .V.
All rig hts reserved.
Pb, Lead Hg, Mercury Cd, cadmium Chromium 6+ PBB PBDE
X O O O O O
Hazardous/toxic Substance
Environmental Protection Use Period
Loading...