Philips CID2680/93 Quick Start Guide

Register your product and get support at

www.philips.com/welcome

CID2680

ENG Quick Start Guide

1

b

a

a
b

c
d

e
f

j

i

h

g

c

Yellow Green Blue

Black

Touch controller

Yellow

Black

Yellow

Red

White

Yellow

Red

Yellow

White

Rear screen

Red

White

Red

Brown

Yellow

Red

White

Amplifier

2

3

4

a

3.5mm

187 mm

116 mm

b

5

P

P

r

a

a

n

i

n

h

i

C

h

C

n

r

i

n

i

n

t

i

n

t

g

i

i

n

n

g

i

6

English

Connect wires

1

Install the car audio

These instructions are for a typical installation.
However, if your car has different requirements,
make the corresponding adjustment. If you have
any questions regarding installation kits, consult your
Philips car audio dealer.

Caution

•

This unit is designed for negative ground
(earth) 12 V DC operation only.

•

Always install this unit in the car dashboard.
Other locations can be dangerous as the rear
of the unit heats up during use.

•

To avoid short-circuit: before you connect,
ensure that the ignition is off.

•

Ensure that you connect the yellow and red
power supply leads after all other leads are
connected.

•

Ensure that all loose leads are insulated with
electrical tape.

•

Ensure that the leads do not get caught under
screws orin parts that will move (e.g. seat rail).

•

Ensure that all ground (earth) leads are run to
a common ground (earth) point.

•

Use only the supplied mounting hardware for
a safe and secure installation.

•

Improper fuses can cause damage or fire.
When you need to change the fuse, consult a
professional.

Note on the power supply lead (yellow)

When you connect other devices to this •
system, ensure that the rating of the car
circuit is higher than the total fuse value of all
the connected devices.

Notes on speaker connection

Never connect speaker wires to the metal •
body or chassis of the car.

Never connect speaker wires with stripes to •
one another.

Caution

•

Ensure that all loose leads are insulated with
electrical tape.

Check the car’s wiring carefully, then connect

1

them to the two supplied ISO wires.

Connector Connect to

Brown wire Telephone mute

1

Red wire The +12V power terminal

2

which is live in the
accessory (ACC) position
of the ignition switch

If there is no accessory
position, connect to the
+12V car battery terminal
that is always live. Be sure
to connect the black ground
(earth) lead to a metal
surface of the car first.

Orange wire Illumination switch

3

Black wire A metal surface of the car

4

First connect the black
ground (earth) lead, then
connect the yellow and red
power supply leads.

Yellow w ire The +12V car battery which

5

is live at all times.

Blue wire The electric antenna control

6

lead or power supply lead
of the antenna booster

If there is no electric antenna
or antenna booster, or it is
manually operated telescopic
antenna, it is not necessary
to connect this lead.

7

Green and
green/black
wires

Left speaker (Rear)

a

White and

8

white/black
wires

Gray and

9

gray/black
wires

Purple and

0

purple/black
wires

Connect the other end of the two ISO

2

connectors to the car audio system.

If necessary, do the other connections.

3

Connect GPS antenna

To receive signal from satelite, you need to connect
the supplied GPS antenna to your car and the
system.

Connect the supplier GPS antenna to the

1

system first.

Stick the other end of the GPS antenna to a

2

metal surface of the car.

Left speaker (Front)

Right speaker (Front)

Right speaker (Rear)

2

b

c

If the car does not have an on-board drive or

1

navigation computer, disconnect the negative
terminal of the car battery.

If you disconnect the car battery in a car •
that has an on-board drive or navigation
computer, the computer may lost its
memory.

If the car battery is not disconnected, •
to avoid shor t-circuit, ensure that bare
wires do not touch each other.

Ensure that car dashboard opening is within

2

these measurements:

Since the unit cannot be used if the •
dashboard opening’s slant angle is above
20 degrees: Ensure that the horizontal
slant of the car dashboard opening is
between 0 and 20 degrees.

a

3 Slide the unit into the dashboard until a click

sound is heard.

b

4 Attach the trim plate.
5 Reconnect the negative terminal of the car

battery.

Connect radio antenna

If your car has built-in radio antenna, connect it to
the radio antenna of the system for better radio
signal.

Connect the radio antenna to the car

1

antenna.

Mount in the dashboard

Note

•

Check wire connection before you mount
the unit into a car.

•

If preset radio stations are lost when the
ignition key is turned OFF and then back
ON, reconnect the red leads crosswise to
the yellow ones.

3

4

Turn on

Caution

•

Risk of road accidents! Never watch video or
adjust settings while you drive.

1 Press to turn on the unit.

The available OSD (On-Screen Display)

»

languages are displayed.

2 Touch a language to select.

The OSD language is changed to the

»

selected language immediately.

To adjust screen brightness/contrast, •

/ on the remote control, then

press

, , or .

press
To turn off the unit, press •

for 3 seconds.

Set date and time

Touch the upper left corner to display main

1

menu.

Set time

Touch [Time].

1

Touch on the displayed time.

2

A submenu is displayed.

»

3 Touch or to set hour and minute.

Tip

•

When date/time is set, touch
then touch

to return to main menu.

first and

2 Touch in the middle right side of the screen.

The second main menu is displayed.

»

3 Touch [Settings].

Touch [Time].

4

The date/time setup menu is displayed.

»

Set date

Touch [Date].

1

Touch on the displayed date information.

2

A submenu is displayed.

»

3 Touch or to set year, month and day.

Set clock mode

1 Touch [Clock mode].
2 Touch on [12Hr] or [24Hr] to select clock

mode.

Use map

Note

•

You may need to upgrade the map before
using it (see “Upgrade the map” section)

1 Touch the upper left corner to display home

menu.

2 Touch [Navigation].

The navigation menu is displayed in a few

»

seconds.

3 Refer to the map manual (in Chinese) to

operate the navigation tool.

Tip

You can press •NAVI to enter/exit the
navigation system.

Tune to a radio station

1

Touch the upper left corner to display home

menu.

2 Touch [Radio].

Band and frequency information is displayed.

»

3 Touch on FM or AM to select band:

FM band options: • FM1, FM2, FM3
AM band options: • AM1, AM2

4 Briefly touch or to tune to a radio station

by step.

Touch •
to a radio station automatically.

or for over 1 seconds to tune

Connect USB device

Note

•

Ensure that the device contains playable
content.

6

1 Open the USB door.
2 Inser t the small end of the supplied USB cable

to the USB socket, then connect the other
end of the USB cable to your USB device.

Play starts automatically.

»

Pair the Bluetooth-enabled
devices

To connect your Buetooth device to the unit, you
need to pair the device to the unit. Pairing needs
only to be done once. You can pair up to eight
devices.

1 Turn on the Bluetooth function on the device.
2 Search for Bluetooth device with the device.

Load discs

You can play video, audio or images stored on the
following discs:

DVD video, DVD-R, DVD-RW•
VCD•
Audio CD, CD-R, CD-RW•

Note

Ensure that the disc contains playable •
content.

5

1 Inser t the disc into the disc slot with label side

facing up.

Play starts automatically.

»

To remove the disc, press the

»

When the disc is ejected, the unit

»

switches to the previous source, if
connected. Otherwise, the unit switches to
[Radio] mode automatically.

button.

3 Select “CID2680” in the pairing list.
4 Enter default password “0000”.

iI pairing succeeds. phone call record iis

»

displayed.

Make a call

1 Pair the phone with the unit.
2 Touch the upper left corner to display the

home menu.

3 Touch [Bluetooth].

The Bluetooth menu is displayed.

»

2 When conversation ends, touch (red) to

terminate the call.

Tip

•

You can select to receive calls manually by
set [Auto answer] to [Off ] status.

Adjust sound

4 Touch or to select the paired phone,

then touch

.

5 Touch or to search for phone number

from the following list:

Or touch to dial number directly, then touch
to dial.

Receive call

By default, all incoming calls are received
automatically.

1 If there is incoming call, [Incoming call...]

flashes on the screen. Speak into the
Bluetooth microphone.

Adjust volume

1 Turn clockwise to increase volume.

Turn •

anti-clockwise to reduce volume.

Mute

1 During play, press .

To turn the sound back on, press •
again.

Tip

You can also turn off sound by touching •
on the screen.

Select preset equalizer

You can select preset equalizer:

Touch anywhere except for the upper left

1

corner to display menu on the screen, if
necessary.

2 Touch .

The current Equalizer setting is displayed.

»

3 Touch or to select an EQ.
4 Touch or to adjust below settings:

• [Bass]bass range: -14 to +14 .

• [Mid]mid dle range: -14 to +14.

• [Treb]treble range: -14 to +14

• [LPH] low pass filter range: 60, 80,
100, 20 0.

• [MPF]middle pass filter range: 500, 1K,

1.5K, 2.5K.

• [HPF]high pass filter range:10K, 12.5K ,
15K, 17.5K.

5 Touch to restore the above settings into

default settings.

6 Press to exit.

© 2009 Koninklijke Philips Electronics N.V.

All rights reserved.

CID2680_93_QSG_V1.0