Register your product and get support at
CEM5000
EN Quick Start Guide
1
a
b
c
def
g
23
45
6
5mm
5mm
Overview of parts 1
These are the supplied parts needed to connect
and install this unit.
In-car audio system and sleeve
a
b Front panel
c Standard connector
d Trim plate
e Rubber cushion
f Disassembly tools
Screws (4 pieces)
g
Connect wires
Caution
• Ensure that all loose leads are insulated with
electrical tape.
ISO connectors 2 3
1 Pull out the ISO connectors from the car
dashboard and connect them to the bigger
end of the supplied standard connector.
2 Connect the other end of supplied standard
connector to the unit.
3 Do the other connections, if applicable.
Without ISO connectors 3 4 5
1 Cut off the bigger end of the supplied
standard connector.
2 Check the car’s wiring carefully, then connect
them to the standard connector.
3 Connect the supplied standard connector to
the unit.
4 Do the other connections, if applicable.
Connector Connect to
1 Black wire A metal surface of the car
First connect the black
ground (earth) lead, then
connect the yellow and red
power supply leads.
2 Yellow wire The +12V car battery which
is live at all times .
3 Blue wire Motor/electric antenna relay
control lead/Amplifi er relay
control lead
4 Red wire The +12V power terminal
which is live in the accessory
(ACC) position of the
ignition switch
If there is no accessory
position, connect to the
+12V car battery terminal
that is always live. Be sure
to connect the black ground
(earth) lead to a metal
surface of the car fi rst.
5 Green and
green/black
wires
6 White and
white/black
wires
7 Gray and
gray/black
wires
8 Purple and
purple/black
wires
Left speaker (Rear)
Left speaker (Front)
Right speaker (Front)
Right speaker (Rear)
Mount in the dashboard 6
1 If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
If you disconnect the car battery in •
a car that has an on-board drive or
navigation computer, the computer may
lose its memory.
If the car battery is not disconnected, •
to avoid short-circuit, ensure that bare
wires do not touch each other.
2 Remove the two screws on the top of the
unit.
3 Remove the mounting sleeve with the
supplied disassembly tools.
4 Ensure that car dashboard opening is within
these measurements.
5 Install the sleeve into the dashboard and
bend the tabs outward to fi x the sleeve.
6 Place the supplied rubber cushion over the
end of the mounting bolt.
7 Slide the unit into the dashboard until you
hear a click sound.
8 Reconnect the negative terminal of the car
battery.
Attach the front panel 6
1 Attach the trim plate to the main unit.
2 Inser t the right side of the panel in the
chassis until it is correctly engaged.
3 Push the left side of the panel and point the
left hole at the left pillar.
4 Release the panel to engage the left side.
5 Push the front side of the panel backward to
the main unit a “click” is heard.
3 Press
SET] (clock set) displays.
or repeatedly until [CLOCK
Hour digits blinks »
4 Set hour with rotary encoder knob.
5 Press OK / MUTE to confi rm.
Minute digits blinks »
6 Set minute with rotary encoder knob.
7 Press
menu.
to confi rm clock set and exit the
Listen to radio
1 Press SOURCE repeatedly to select [Radio] .
2 Press
3 Press
[FM3] , [AM1] , or [AM2] .
manually.
The radio station is broadcast. »
Play with RDS
The RDS (Radio Data System) function operates
only in areas with FM stations broadcasting RDS
signals. If you tune to an RDS station, an RDS icon
and information about the presenter, station or
program is displayed.
to select band: [FM1] , [FM2] ,
or
or
to tune to a radio station
Turn on
1 Press
to turn on the unit.
To turn off the unit, press •
seconds.
for 3
Set clock
1 Press MENU repeatedly until [TIME
FORMAT] (time format) displays.
2 Use rotary encoder knob to toggle the
settings:
[TIME FORMAT 12H] •
[TIME FORMAT 24H] •
Turn on RDS
Note
• By default, the RDS function is off.
• must be
To adjust the RDS function, the unit
under Radio playback mode.
1 Press MENU for 3 seconds.
2 Rotate encoder knob to select [RDS ON] :
To turn off the RDS function, repeat •
steps above and choose [RDS OFF] .
Pairing bluetooth devices
You can pair your bluetooth device with the unit
as follows:
1 Turn on bluetooth function on the device.
2 Search for other bluetooth devices that can
pair with your device.
3 Select “Philips” in the pairing list.
4 Enter default password “0000”.
» [Paired Ok!] (paired ok) displays on the
panel if pairing is successful.
The paired device connect to the car »
audio system automatically.
Make a call
Note
To make a call on this unit, the bluetooth •
connection between the unit and the phone
must be active.
1 Press until [NUM DIAL] displays.
2 Press 0-9 to enter phone number.
Press •
to delete entered numbers.
3 Press to dial.
To redial number:
Terminate call
1 Press to terminate call.
1 Press .
2 Press or to choose [REDIAL] (redial).
3 Press again.
[Calling] » (calling) displays and the unit
To quick dial preset number:
starts dialing the number dialed last time.
1 Press .
2 Press or to choose [QUICK DIAL] .
3 Press 1 to 6 numeric keys to choose preset
numbers.
» Preset phone number displays.
4 Press again.
[Calling] » (calling) displays and the unit
starts dialing the selected number.
© 2010 Koninklijke Philips Electronics N.V.
All rights reserved.
Document order number: CEM5000_00_QSG_V2.1
Loading...