Page 1
PHILIPS
CONSUMER ELECTRONICS
PHILIPS
□ BQOODO 005717
CD 480 / CD 482
CD
CD
CD
CD
CD
Compact Disc Player
Lecteur de Disques Compacts
Compact Disc-Spieier
Compact Disc-Speler
Reproductor ’Compact Disc’
Lettore di Compact Disc
Compact Disc-Afspiller
Compact Disc-Spelare
Compact Disc -Soitin
Page 2
English
INTRODUCTION
The Compact Disc system is a majorstepforward in
the sphere of audio technology. By employing the
most sophisticated digital andopticaltechnologies,
Compact Disc not only produces the ultimate in
sound reproduction, it also offers unprecedented
ease of operation, with rapid access to every track
on the disc and the possibility of programming.
INSERTING AND REPLACING THE BATTERIES IN
THE REMOTE CONTROL (Hg. 3, CD 482 only)
• Open the battery compartment.
• Insert the two batteries according to the diagram
in the compartment.
• Replace the cover.
The life of the batteries is around one year. Remove
them when they are flat or when you are not
intending to use the remote control forsometime.ln
this way you will prevent damage to the remote
control by possible battery leakage.
For replacement only use batteries of the type R03,
UM4orAAA.
_______________________________
Remote control
The only difference between the Compact Disc
players CD 480 and CD 482 is that the former is
supplied w/f/ioufandthe latter iy///i remote control.
The CD 480 is however adapted for remote control.
This allows itto be operated remotely if it is connect
ed to a PHILIPS HiPi-system with remote control, or
if use is made of the remote control receiver
EM 2200, available as an accessory, and one of the
transmitters RC 771, RC 772 or RC 773.
In addition to its own remote control system, the
CD 482 also offers the possibility of remote control
via a PHILIPS HiR-system.
CONTENTS Page
INSTALLATION 2
OPERATION 3-5
PROGRAMMING 6
ADDITIONAL INFORMATION 7
FAULTS AND THEIR LIKELY CAUSES 7
ILLUSTRATIONS 60
INSTALLATION
CHECKING THE POWER SUPPLY SETTING
(Fig- V
• Check that the type plate on the rear of your
player indicates the correct supply voltage.
• If your mains supply voltage is different, consult
your dealer or our Service Organisation.
REMOVING THE TRANSIT CLAMPS (Fig. 2)
The two red transit clamps on the bottom lock the
play mechanism to protect it during transportation.
• Turn the player upside down.
• Turn the clamps anti-clockwise and remove them
from the piayer.
• Store them in the recesses provided.
If you wish to transport the player, reinsert the
clamps and rotate them clockwise until they lock in
position.
SITING THE COMPACT DISC PLAYER
Free-standing
• Always position the player horizontally on a flat,
firm surface.
• Allow a free space of at least 3 cm above the
player so as notto interfere with the cooling of the
player.
In an audio rack
• The player can be sited in any desired position.
Stacked
• Site the player preferably at the bottom or at the
top.
• Never position the player directly on top of a
high-power amplifier, as such an amplifier gives
off a substantial amount of heat.
Warning
Never allow the player to stand for long periods in
direct sunlight or near a heat source.
CONNECTIONS (Fig. 4)
a RC5IN/OUT: for a remote control system.
Use this connection for:
- Connecting up the equipment when you are
incorporating the player in a PHILIPS HiR-system
with remote control.
- Connecting the remote control receiver EM 2200.
b OUTLR: for the connecting cable to the am
plifier.
• Insert a red plug into the ’R’ socket (right-hand
channel) and the other plug into the ’L’ socket
(left-hand channel).
• Insert the two other plugs into the corresponding
sockets of the CD or AUX input of your amplifier.
You can also usetheTUNER or TAPE IN connec
tion, but
suitable for Compact Disc reproduction.
c Connection forthe mains lead.
never the PHONO input. This is not
Page 3
OPERATION
EXPLANATION OF KEYS ETC. (Fig. 5)
1 ON/OFFkey
> For switching on and off.
2 PAUSE LED
> Lights up when the player is in the pause mode.
3 TRACK LED
> Lights up when you switch on the player.
> Indicates that the display is showing the track
numbers and any index numbers of the disc.
4 REMOTE LED fCD4S2on/y;
> Lights up briefly when the REM CONTROL eye
receives a command from the remote control.
5 time LED
) Lights up during the display of the playing time of
a track or the disc.
6 MULTIMODE CD LED DISPLAY
> Informs you about the functioning of the player.
> Displays details from the disc contents list.
See also: The information on the display’.
7 REM CONTROL eye (CD 482 only)
> Receives the signals from the remote control.
8 REPEAT key
> For repeating a disc or a programme.
9 «SEARCH»keys
> For fast search to a particular passage during
play. (’«’ backwards, ’»’ forwards.)
10 PHONES socket
) For connection of headphones.
See also: 'Listening with headphones'.
11 OPEN/CLOSE key
> For opening and closing the disc tray.
12 REPEAT LED
> Lights up when you repeat a disc or programme.
13 SHUFFLE LED
> Lights up when you play a disc in random order.
14 PLAY key
) For starting play.
> For returning to the beginning of a track.
15 STOP/CM key
> For stopping play (STOP).
> For erasing a programme (CM = Clear Memory).
16 PREV and NEXT keys
> For selecting a previous or a later track during
play.
) For selecting the track number you want play to
begin with.
> For selecting track numbers when compiiing a
programme.
(’PREV from high to low, 'NEXT' from low to high.)
17TRACK/TIMEkey
> For selecting between track number and playing
time indication.
18 PROGRAM key
> For storing track numbers in a programme.
> For erasing track numbers from a programme.
> For checking the programme.
19 PAUSE key
> For briefly interrupting play.
> For holding play at the start of a disc, track or
passage.
20 SHUFFLE key
> For playing all tracks on a disc in random order.
Remote control (CD 482 only)
The keys of the remote control have the same
function as the corresponding ones on the player.
For the best reception of its signals you should aim
the remote control as directly as possible at the
REM CONTROL eye. The REMOTE LED lights up
briefly when this eye receives a command.
If the siting of the player does not allow direct
reception of the signals, you may connect the
EM 2200 as remote control receiver.
THE INFORMATION ON THE DISPLAY (Fig. 6-13)
Each Compact Disc has, along with the music, a list
of contents detailing the numbers of the tracks, the
playing time of each track and the total playing time
of the disc. The player always scans this first and
stores it in its memory in order, for instance, to
provide information via the display.
On/off indication (6)
When the player is switched on, the ’—’ indication
lights up. It goes off again when the player is
switched off.
'PLAY' indication (7)
When the tray is closed either by hand or by
pressing PLAY, the 'PLAY' indication appears and
will remain on until the player has finished scanning
the contents list and begins playing.
Track number indication (8)
Under 'TRACK' the display shows the number of the
track which is being played. The TRACK LED lights
up.
Index number indication (9)
The figures under 'INDEX' are the index numbers.
They will only change if the track is subdivided with
the aid of index numbers.
Elapsed playing time indication (10)
If you press the TRACK/TIME key, the display will
show under 'min’ and 'sec' the elapsed playing time
from '0:00' of each track. The time LED lights up.
Number of tracks indication (11)
If the tray is closed by pressing OPEN/CLOSE, the
’—’ indication flashes until the contents list of the
dischasbeen scanned. The display then shows the
number of the tracks on the disc under 'TRACK', for
example '16'.
___________
Page 4
Total playing time indication (12)
If you close the tray by pressing OPEN/CLOSE and
press TRACK/TIME, the display will show the total
playing time of the disc under 'min’ and ’sec’, for
example ’62:13’.
Error indication (13)
If you make a mistake, the indication ’Err’ (for Error)
will appear briefly.
SWITCHING ON AND OFF (ON/OFF)
Switching on
• Press ON/OFF.
> The TRACK LED and the ’—’ indication light up.
Switching off
• Press ON/OFF again.
I All lights are extinguished.
LOADING AND UNLOADING THE DISC
(OPEN/CLOSE)
Loading (Fig. 14-16)
• Open the disc tray by pressing OPEN/CLOSE.
• Insert the disc into the tray printed side up.
• To close the tray:
- Press the front of the tray lightly or press PLAY if
you wish to simply play the disc.
- Press SHUFFLE if you wish the disc to be played
in random order.
- Press OPEN/CLOSE if you wish to start with a
track number other than the first one or you wish
to compile a programme.
If ’Err’ appears after the tray is closed, this means
that you have loaded the disc upside down or it is
dirty, badly scratched or faulty, for example warped.
’Err’ also appears if you close an empty tray by
hand, by pressing PLAY or SHUFFLE.
Unloading
• Open the tray by pressing OPEN/CLOSE.
• Hold the disc in same way as when loading.
• Store the disc immediately in its holder. This
prevents soiling and damage.
• Close an empty tray by pressing OPEN/CLOSE.
Avoid leaving the tray open, to prevent dust from
entering.
PLAYING THE ENTIRE DISC (PLAY)
• Close the tray by hand or by pressing PLAY.
> ’PLAY’ appears on the display.
) Play starts as soon as the first track number
appears on the display as ’1:01 ’.
> At each following track the track number jumps
on.
> After the last track the disc stops.
The display shows the number of tracks on the
disc.
If you have selected playing time indication, you will
see ’1:00’ appear briefly first. Play now starts at the
moment that the elapsed playing time of the first
track is displayed. With each following track any
preceding pause is first counted off before the
display of the playing time starts again at ’0:00’.
GOING BACK TO THE BEGINNING OF A TRACK
(PLAY)
• Press PLAY.
> The track starts again from the beginning.
SELECTING ANOTHER TRACK DURING PLAY
(NEXT or PREV)
Selecting a following track
• Press NEXT until the desired track number ap
pears on the display.
> Play is interrupted when the key is released.
> The selected track begins to play a few moments
later.
If you press NEXT while playing the last track, ’Err’
appears to remind you that there is no next track
and playing of the last track continues. If the player
is in the repeat mode, then play continues with the
first track.
Selecting a previous track
• Press PREV until the required track number
appears on the display.
> Play is interrupted when the key is released.
> The selected track begins to play afew moments
later.
If you press PREV while playing the first track, ’Err’
appears to remind you that there is no previous
track and playing of the first track continues. If the
player is in the repeat mode, then play continues
with the last track.
CHANGING TO PLAYING TIME INDICATION
(TRACK/TIME)
After switching on, the display always gives the
track number indication.
• Press TRACK/TIME if you wish instead to seethe
playing time.
• Press TRACK/TIME again to return to track
number indication.
The track numberindication returns automatically if
the disc is stopped or the tray is opened.
SEARCHING FOR A PARTICULAR PASSAGE
DURING PLAY (« SEARCH »)
• Hold « SEARCH down to search backwards to
the beginning.
• Hold SEARCH» down to search forwards to
the end.
As soon as the key is released play restarts at once.
The length of time for which you hold the key down
determines the search speed:
Page 5
- the first three seconds relatively slowly;
- after approx, four seconds slightly faster;
- the highest speed is reached after approx, seven
seconds.
Atthe first two speeds the sound of the disc remains
audible, although accelerated. When searching by
ear it is therefore advisable to release the key as
soon as the sound disappears. If you have pressed
PAUSE before you started the search, you will hear
nothing.
As soon as you reach the beginning of the first
track, ’Err’ appears. Play will resume there as soon
as you release the key. If you reach the end of the
last track, ’Err’ will also appear. If you then release
the key, play will resume a few seconds before the
end of the disc.
BEGINNING WITH A TRACK NUMBER OTHER
THAN THE FIRST
(NEXT or PREV and PLAY)
• Close the tray by pressing OPEN/CLOSE.
) The highest selectable track number appears on
the display.
• Press NEXT or PREV until the required track
number appears, if you require the highest num
ber, you must still press PREV once.
• Press PLAY.
) Play will start from the selected track.
PLAYING THE DISC IN RANDOM ORDER
(SHUFFLE)
• Close the tray by pressing SHUFFLE.
) ’PLAY’ appears on the display.
> The SHUFFLE LED lights up.
) All the tracks on the disc are played in a sequence
to be determined by the player.
> When all the tracks have been played the disc
stops.
The SHUFFLE LED goes out.
The display shows the number of tracks on the
disc.
During play you can return to a track which has
already been played by pressing PREV. if you press
NEXT you are selecting any one of the following
tracks.
You can stop random order play at any time by
pressing SHUFFLE again.The remainderof the disc
is then played in the normal sequence.
By pressing REPEAT you can repeat random order
play. The player then always begins with the same
track, but otherwise changes the sequence every
time the disc is repeated.
____________________________
________
BRIEFLY INTERRUPTING PLAYBACK/HOLDING
PLAY AT THE START OF A DISC, TRACK OR
PASSAGE (PAUSE)
To briefly interrupt playback
• Press PAUSE.
> The PAUSE LED lights up.
) The sound stops but the disc continues to spin.
• Press PAUSE again to restart.
} The PAUSE LED goes out.
> Play restarts atthe point where it was interrupted.
Holding piay atthe start of a disc, track or passage
You can go to any place on the disc and hold it by
pressing PAUSE before;
- starting to play the disc;
- going back to the beginning of a track;
- selecting another track;
- searching for a particular passage;
- beginning with a track other than the first one;
- playing the disc in random order.
Press PAUSE again to start play at the chosen
place.
REPEATING THE DISC (REPEAT)
• Press REPEAT before or during playback.
) The REPEAT LED lights up.
• Press REPEAT again to stop repeating.
> The REPEAT LED goes out.
> The disc will play on to the end and then stop.
Repeating can also be stopped by pressing STOP/
CM or OPEN/CLOSE.
STOPPING PLAYBACK
(STOP/CM or OPEN/CLOSE)
• Press STOP/CM if you merely wish to stop.
> The number of tracks on the disc will appear on
the display.
• Press OPEN/CLOSE if you wish to stop and take
out the disc.
> The indication ’—’ will appear on the display.
________________________
Page 6
PROGRAMMING
By programming the player you can play up to
20 tracks of a disc in any required sequence. Each
track can however only be selected once. If you
exceed the maximum of 20 tracks. ’Err’ appears.
Programming is only possible when the disc is not
playing. Once playing has started it is no longer
possible to change the programme.
STORING A PROGRAMME
• Close the tray by pressing OPEN/CLOSE.
> The highest track number you can store appears
on the display.
• Press NEXT or PREV until the first track number
you wish to programme is displayed. If you
require the highest number on the disc as the first
track, you must still press PREV once.
> Afterthe numberyou willsee aflashing colon sign
followed by a dash.
• While the colon is flashing press PROGRAM.
> The colon sign will stop flashing.
> The dash will be replaced by ’P’ (for Programme).
> That number has been stored.
• Store each of the remaining track numbers re
quired in the same way.
Warning - The colon will flash for approx. 7 sec.
each time. If you fail to press PROGRAM within that
time, the colon will stop flashing. You can then no
longer store the number: instead of the ’P’ you will
see ’Err’ - or the numbers already stored will appear
- if you press PROGRAM too late. You can however
still store such a missed number by returning to it
from the previous or the following number.
For example:
On a disc with 16 tracks you wish to listen to the
numbers 7, 3,9,5,12 and 10 in that sequence.
• Load the disc in the tray and close it by pressing
OPEN/CLOSE.
> Afew moments laterthe display will indicate ’16’.
• Press NEXT until the display shows ’7:-’ and
press PROGRAM.
> You will then see ’7: P’.
• Go back to ’3: -’ using PREV and press
PROGRAM again.
> You will now see ’3: P’.
• Display the numbers 9, 5, 12 and 10 in turn by
pressing NEXT or PREV and store them by
pressing PROGRAM after each one.
> When the last number has been stored the
display will show ’10: P’ continuously.
Incur example: you have stored ’4’ instead of ’5’. Go
to ’3’ using PREV, return to ’4’ using NEXT and press
PROGRAM. You will then see ’4: C’. Now proceed
to store ’5’.
CHECKING THE PROGRAMME
• You can check the track numbers you have
stored by pressing PROGRAM.
> All the track numbers appear in the programmed
sequence on the display.
In our example: ’-7-’ ’-3-’ ’-9-’ ’-5-’ ’-12-’ ’-10-’
’10: P’.
If ’Err’ appears, this means that no track numbers
have yet been stored.
ERASING A TRACK NUMBER FROM THE
PROGRAMME OR THE ENTIRE PROGRAMME
• Bring up the track numberyou wish to erase by
pressing NEXT or PREV.
• While the colon is flashing press PROGRAM.
) The ’P’ after the number is replaced by a ’C’ (for
Clear).
• Press STOP/CM if you wish to erase the entire
program.
> The display shows the number of tracks on the
disc.
PLAYING THE PROGRAMME
• Press PLAY.
> Play starts as soon as the first number of the
programme appears on the display; in our exam
ple:’7:01’.
> As play continues the following numbers in the
sequence appear.
> The entire programme can be displayed by
pressing PROGRAM.
All functions of the player can be used during
programmed play except for;
- Beginning with a track other than the first one on
the programme using NEXT or PREV and PLAY.
- Playing in a random order with SHUFFLE.
Searching for a particular passage is limited to
within the track being played. When either end of the
track is reached ’Err’ appears.
When STOP/CM is pressed or when all the tracks of
the programme have been played, the disc stops,
but the programme remains stored.
The programme will be erased when you open the
tray. It will also be erased if you press STOP/CM
twice in succession
during playback.
RECTIFYING A MISTAKE
• Go to anothertrack number by pressing NEXT or
PREV.
• Return to the wrong number.
• While the colon is flashing press PROGRAM.
> The ’P’ after the number is replaced by a ’C’ (for
Clear).
• Store the correct number.
Page 7
ADDITIONAL INFORMATION
LISTENING WITH HEADPHONES (PHONES)
Connect headphones with a 6.3 mm jack plug and
an impedance between 8 and 1000 ohms to the
PHONES socket.
The sound level you hear is dependent on the
impedance of the headphones and the signal level
on the disc itself.
CARE OF THE DISCS
Although both sides of a disc are protected by a
special coating, it is still advisable to treat the discs
with care:
• Never leave discs lying around, put them back in
their holders immediately after use.
• Neverwrite on the printed side!
• Do not attach any stickers on that side.
• Keep the shiny surface of the disc clean. Use a
soft lint-free cloth and always wipe the disc in a
straight line from centre to edge. You may breath
lightly on the disc first.
The cleaning set SBC 3540, available separately, is
a useful accessory for cleaning your discs. It
contains a protective support, a special disc clean
ing cloth and a bottle of cleaning fluid.
Warning - Cleaning agents for conventional rec
ords are not suitable for cleaning a Compact Disc.
Nor may detergents or abrasive cleaning agents be
used.
____________________________________
PLAYER MAINTENANCE
A chamois leather slightly moistened with water is
sufficient for cleaning the player. Do not use clean
ing agents containing alcohol, spirits, ammonia or
abrasives.
The disc tray should be kept free of dust with a dry
cloth.
____________________________________
TECHNICAL DATA
Typical Audio Performance
Frequency range: 2-20,000 Hz
Amplitude linearity: ±0.1 dB (20-20,000 Hz)
Phase linearity: ±0.7° (20-20,000 Hz)
Dynamic range: >86 dB (20-20,000 Hz)
Signal-to-noise ratio: >93 dB (20-20,000 Hz)
Channel separation: 94 dB (1 kHz)
Total harmonic distortion: 0.016% (1 kHz)
Wow and flutter: quartz crystal precision
D/A conversion: quadruple oversampling
(176.4 kHz) with digital filter and two 16-bit D/A-converters
Audio output level: 2 V^s
Impedance PHONES socket: 8-1000 ohms
___________________________
Power supply
Mains voltage and frequency: see the type plate on
the rear of the player
Power consumption: 15 W approx.
Safety requirements: lEC
Cabinet
Material/finish: metal and polystyrene with decora
tive trim
Dimensions (w x h x d) : 420 x 80 x 300 mm
Weight: 3.5 kg approx.
Subject to modification
This Compact Disc player compiies with radio
interference requirements as iaid down in EC
reguiations.
FAULTS AND THEIR LIKELY CAUSES
Insufficient familiarity with the combination of a new
product and new discs may lead to faults arising
during use. These are generally caused by simple
errors in operation or external factors.
It is perhaps useful to check the points listed below
and where possible remedy these before taking
your player for repair.
- The transit clamps have not been removed.
- Condensation has formed on the lens of laser
due to a dramatic change in temperature. This wiil
disappear automatically after a some time.
- There is a foreign object in the disc tray.
- The disc has not been inserted with the printed
side up or there is no disc in the tray.
- The disc is dirty, badly scratched or warped.
- The player has been connected to the PHONO
socket of the amplifier.
If the fault remains, try to clear it by switching the
player off and on.
If this also fails to help, do not continue experiment
ing, but remove the plug from the socket and
consult your dealer.
Certain faults may be caused by a disc. In order to
help determine the precise cause, take the disc with
which the fauit occurred with you when you take the
player for repair.
Under no circumstances should you repair the
player yourself, as this will invalidate the guaran
tee!
Page 8
TRACK /mif! 5f-i0sJ</Sô
2 3 45 6 7 8 9
Il
lf.,„
¿■.i...:
11121314 15 16 17181920
.............
_____
\
Page 9
English
Figures
page 2
page 60
Français
Figures
)
Deutsch
Abbildungen
Nederlands
Figuren
Español
Figuras
Italiano
Figure
Dansk
Figurer
Svenska
Rgurer
Suomi
Kuvat
радев
page 60
Seite 15
Seite 60
pagina 22
pagina 60
página 28
página 60
pagina 35
pagina 60
side 42
side 60
sida 48
sida 60
sivu 54
sivu 60
Page 10
3104106 93601
Printed in Belgium
688/1
Loading...