Philips CCC130AT99, CCC190AT99, CCC192AT99, CCC132AT99 User Manual

CCC130AT
CCC132AT
CCC190AT
CCC192AT

Color TV with built-in VCR
Owner’s Manual

Once your PHILIPS purchase is registered, you’re eligible to receive all the privileges of owning a
PHILIPS product. So complete and return the Warranty Registration Card enclosed with your
purchase at once. And take advantage of these important benefits.

Return your Warranty Registration card today to

ensure you receive all the

benefits

you’re entitled to.

For Customer Use

Enter below the Serial No.
which is located on the rear of
the cabinet. Retain this infor­mation for future reference.

Model No. ________________
Serial No. ________________

Congratulations on your purchase, and
welcome to the “family!”

Dear PHILIPS product owner:

Thank you for your confidence in PHILIPS. You’ve selected one of
the best-built, best-backed products available today. And we’ll do
everything in our power to keep you happy with your purchase
for many years to come.
As a member of the PHILIPS “family,” you’re entitled to protection
by one of the most comprehensive warranties and outstanding ser­vice networks in the industry.
What’s more, your purchase guarantees you’ll receive all the infor­mation and special offers for which you qualify, plus easy access to
accessories from our convenient home shopping network.
And most importantly you can count on our uncompromising
commitment to your total satisfaction.
All of this is our way of saying welcome-and thanks for investing in
a PHILIPS product.

Sincerely,

Robert Minkhorst
President and Chief Executive Officer

P.S. Remember, to get the most from your PHILIPS

product, you must return your Warranty
Registration Card within 10 days. So please mail
it to us right now!

Know these

safetysymbols

This “bolt of lightning” indi-

cates uninsulated material
within your unit may cause an
electrical shock. For the safety
of everyone in your household,
please do not remove product
covering.

The “exclamation point”

calls attention to features
for which you should read the
enclosed literature closely to
prevent operating and mainte­nance problems.

WARNING: TO PREVENT
FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR
MOISTURE.

CAUTION: To prevent elec­tric shock, match wide blade of
plug to wide slot, fully insert.

ATTENTION: Pour éviter les
choc électriques, introduire la
lame la plus large de la fiche
dans la borne correspondante
de la prise et pousser jusqu’au
fond.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

R

E

G

I

S

T

R

A

T

I

O

N

N

E

E

D

E

D

W

I

T

H

I

N

1

0

D

A

Y

S

Hurry!

t

s

Warranty
Verification

Registering your product within
10 days confirms your right to max­imum protection under the
terms and conditions of your
PHILIPS warranty.

Owner
Confirmation

Your completed Warranty
Registration Card serves as
verification of ownership in the
event of product theft or loss.

Model
Registration

Returning your Warranty
Registration Card right away guaran­tees you’ll receive all the informa­tion and special offers which you
qualify for as the owner of your
model.

Visit our World Wide Web Site at http://www.philips.com

Introduction 3

Features

• A-B Repeat Play

• Automatic Channel Setup

• Automatic Head Cleaner

• Automatic Tracking Adjustment

• Blue Background

• Closed Caption

• Daylight-Savings Time

• English or Spanish displays

• High Quality (HQ) System

• One-Touch Recording

• Real-Time Counter

• Remote Control or Front Panel
menu access

• Repeat Play

• ShowGuard

TM

- Indefinite Timer

Recording memory

• Sleep Timer

• SmartClock

TM

• SmartLock

TM

• Special Effects: Forward and
Reverse Searching; Still

• S-VHS Quasi Play Back (SQPB)

• Timer Recording

• Wake Up Timer

Safety Precautions

Warning: To prevent fire or shock hazard, do not expose this
equipment to rain or moisture.
Federal Communications Commission (FCC) Warning: Any
unauthorized changes or modifications to this equipment void the user’s
authority to operate it.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a partic­ular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

Philips Consumer Electronics recommends you use only video cassette
tapes that have the mark. Other tapes may cause poor picture quality
and excessive deposits on the video heads that the warranty may not cover
if damage occurs.
This TV/VCR has a High Quality (HQ) system and is compatible with exist­ing Video Home System (VHS) equipment.
Note to the Cable TV System Installer: This reminder calls the Cable
TV system installer’s attention to Article 820-40 of the National Electrical
Code, which provides guidelines for proper grounding – in particular, speci­fying that the cable ground shall be connected to the grounding system of
the building, as close to the point of cable entry as possible.

Declaration of Conformity

Model Numbers: CCC130AT, CCC132AT, CCC190AT, and CCC192AT
Trade Name: Philips
Responsible Party: Philips Consumer Electronics

P.O. Box 14810
Knoxville, TN 37914-1810
[phone]

Welcome to your TV/VCR owner’s manual.

This manual describes four models: CCC130, CCC132, CCC190 and CCC192. The models may look different,
but they operate exactly the same. The CCC130 is illustrated in this manual. The features described in this
manual apply to all models unless otherwise specified.

As an ENERGY STAR®Partner, Philips Consumer Electronics has determined that this product meets the ENERGY STAR®guidelines for energy
efficiency. E

NERGY STAR

®

is a U.S. registered mark. Using products with the ENERGY STAR®label can save energy. Saving energy reduces air pollution and

lowers utility bills.

SmartClock

TM

, SmartLockTM, and ShowGuardTMare trademarks of Philips Consumer Electronics. Copyright 2001 Philips Consumer Electronics. All rights reserved.

4 Table of Contents

Setting Up Your TV/VCR

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Before Using the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Hooking Up the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7

Turning On the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Automatic Channel Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-11

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-17

Daylight-Savings Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Time Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Description of Controls

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Remote Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-23

Adjusting the Picture Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24-25

On-Screen Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Basic Operations

Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Recording Options

One-Touch Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Rerecording (Tape Duplication) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32-35

Defeat Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Playing Options

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

A-B Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38-39

Real-Time Counter Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Playback Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Additional Features

SmartLock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42-45

Blue Background . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Wake Up Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Volume Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Closed Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50-51

Automatic Operation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Information You May Need

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54-55

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Before Using the TV/VCR 5

Using the Remote Control

● Point the remote control at the TV/VCR’s remote sensor.

● Do not put objects between the remote control and the

TV/VCR.

TV/VCR Maintenance

● In this TV/VCR, use only tapes with the mark.

● Remove any light adhesive stick-on notes from the video cas-

sette tape before putting the tape in the TV/VCR. Removable
labels can jam the TV/VCR.

● The TV/VCR requires periodic maintenance to maintain its

excellent performance. This TV/VCR has an automatic head
cleaning system. However, the video heads will eventually
require cleaning or replacement. Only an authorized service
center should perform this service.

Video cassette tapes have record tabs to ensure you do not
erase recordings accidentally.

1

To prevent accidental recording, break off the tab with a
screwdriver.

2

To record again, cover the hole with cellophane tape.

Recording Prevention

1

2

Battery Safety

● Battery Usage CAUTION - To prevent battery leakage that

may result in bodily injury or damage to the unit:
Install ALL batteries correctly, with the + and - markings on
the battery aligned as indicated on the unit;
Do not mix batteries, for example, old with new or carbon
with alkaline; and
Remove batteries when the unit will not be used for a long
time.

Putting Batteries in the Remote Control

1

Remove the battery compartment lid on the bottom of the

remote control by pressing the tab, then lifting the lid.

2

Place two AA batteries inside the battery compartment

with their +and –ends aligned as indicated.

3

Replace the battery compartment lid.

1 2 3

• Your new product, its packaging, and
this manual contain materials that
can be recycled and reused.
Specialized companies can recycle
your product to increase the amount
of reusable materials and to mini­mize the amount that needs to be
properly disposed.
Your product uses batteries that
should not be thrown away when
depleted but should be disposed of as
small chemical waste.
Please find out about the local regula­tions on disposal of your old product,
batteries, manual, and packaging
when you replace existing equipment.

Helpful Hints

6 Hooking Up the TV/VCR

ANT.

ANT.

Hooking Up Your TV/VCR
With a Cable Signal or
Outdoor Antenna

ANT.

IN

OUT

ANT.

Connect an RF coaxial cable (75­ohm, not supplied) to the OUT Jack
on the Cable Box and to the
ANT(enna) Jack on the TV/VCR.

Connect a Cable signal
or an antenna to the
ANT(enna) Jack.

Hooking Up Your TV/VCR
With a Cable Box

To view any channel, set the
TV/VCR to the Cable Box output
channel (channel 03 or 04). Then,
select channels at the Cable Box.

1

Hook up your TV/VCR using one of the connections shown.

A.

B.

ANT.

ANT.

Rod Antenna

(not supplied)

Hooking Up Your TV/VCR
With an Indoor Antenna

To install a rod antenna (not sup­plied), push the stem of the antenna
into the antenna hole on the top of
the TV/VCR. Connect the antenna
wire to the ANT(enna) Jack on the
back of the TV/VCR as shown.
Extend the antenna and adjust its
length, direction, and angle for the
clearest picture.

C.

Connect the Cable signal to
the IN Jack on the Cable Box.

RF coaxial cable

(not supplied)

CCC130

CCC130

CCC130

Hooking Up the TV/VCR (cont’d) 7

AUDIOVIDEO

STOP
EJECT

REW PLAY F.FWD REC

OTR

CHANNEL

VOLUME

POWER

EARPHONE

OUT

IN

VIDEO

IN

OUT

3CH
4CH

AUDIO

ANT.

OUT

IN

VIDEO

IN

OUT

3CH

4CH

AUDIO

ANT.

VIDEOAUDIO

• Before connecting an antenna or cable signal to the ANT(enna) Jack, make sure the pin is not bent. If the pin is
bent, straighten it as illustrated, then connect the antenna or cable signal to the ANT(enna) Jack.

• A rod antenna (not supplied) is available from Philips Service Solutions Group. The part number is 4835 303

37006. To order, call 1-800-851-8885. (This antenna will fit the CCC130 and CCC132 only.)

• Audio and video cables are not supplied.

Helpful Hints

Crooked Pin

Straight Pin

Bent pin

Plug

Cable

Hooking Up Your TV/VCR to Another Video Source
(VCR or Camcorder)

You may need this connection if you want to copy tapes or view tapes that you are playing on the VCR or
camcorder. Select channel 00 (A/V IN) at the TV/VCR when viewing tapes that are playing on the VCR
or camcorder. Details are on page 31.

AUDIO/VIDEO In Jacks
on front of TV/VCR

AUDIO/VIDEO OUT
Jacks on VCR

Connect an Audio cable to the AUDIO
OUT Jack on the VCR and to the AUDIO In
Jack on the front of the TV/VCR.

Connect a Video cable to the VIDEO OUT Jack on the
VCR and to the VIDEO In Jack on the front of the TV/VCR.

2

When all other connections are complete, plug in the TV/VCR’s power cord.

3

Before you turn on the TV/VCR, go to page eight.

D.

CCC130

8 Turning On the TV/VCR

Before you turn on the TV/VCR, make sure batteries are in the
remote control and you have connected the TV/VCR correctly.
The instructions on this page work only when you turn on the
TV/VCR for the first time.

1

Press the POWER button. The TV/VCR will come on and the

screen shown below will appear.

2

Press the PLAY/K button or the STOP/L button to select
English or Spanish on-screen displays and menus.

3

Press the MENU button. The screen shown below will appear.

4

Press the F.FWD/B button to begin automatic channel
setup. The TV/VCR will memorize all available channels. When

channels are set, CHANNELS ARE SET will appear on the screen
briefly. Then the TV/VCR will go to the lowest available channel.
If you try to set up channels when there is no antenna or cable
connected to the TV/VCR, programming will appear to take place,
but eventually a NO TV SIGNALS ... message will appear on the
screen. Connect an antenna or cable to the ANT(enna) jack on
the TV/VCR, then press the F.FWD/B button again. You may
need to follow the steps on page 10 instead.

CONNECT ANTENNA OR CABLE
TO TVCR

THEN PRESS B

TO END PRESS EXIT

SELECT LANGUAGE

> ENGLISH ON

ESPAÑOL

SELECT KL OR
PRESS MENU TO CONTINUE

5

Use the CH(annel) o/p buttons or the Number buttons
on the remote control to select a TV/VCR channel. Use
the VOL(ume) o/p buttons to adjust the sound.

When you scan channels with the CH(annel) o/p buttons, only
the memorized channels will be available. Use the Number but­tons to select non-memorized channels.

• If you do not see any on-screen dis­plays when you turn on the TV/VCR,
check your hookups, then try again.
If you still do not see any on-screen
displays, follow the steps on pages
nine-10 to select a language and set
up channels.

• To skip step 2, press the MENU but­ton. All on-screen displays will be in
English. To skip step 4, press the
STATUS/EXITbutton. Automatic
Channel Setup will not occur, and
CHANNELS NOT SET will appear on
the screen briefly.

• You cannot set up channels if you are
using a Cable Box.

• Line Input mode is channel 00.
When you select channel 00, A/V IN
will appear on the screen briefly.
Press the CH(annel) o/p buttons or
the Number buttons to select another
channel.

Helpful Hints

1

3
5

2

4

EJECT

MENU

SLEEP/

WAKE UP

CH. VOL.

POWER

STATUS/EXIT

1 2 3

4 5 6

7 8 9

0

REC
/OTR

PLAY

REW

F.FWD

STOP

MUTE

SPEED

MEMORY

TRACKING

CLEAR

ALT.CH

PAUSE

/STILL

Language Selection 9

Follow the steps below to change the language of the on-screen
displays and menus.

3

Press the PLAY/▲ button or the STOP/▼ button to
choose SELECT LANGUAGE. Then, press the F.FWD/B
button.

4

Press the PLAY/▲ button or the STOP/▼ button to select
ENGLISH or ESPAÑOL (Spanish).

5

Press the STATUS/EXIT button.

SELECT LANGUAGE

> ENGLISH ON

ESPAÑOL

SELECT KL
TO END PRESS EXIT

1

Press the MENU button.

2

Press the PLAY/▲ button or the STOP/▼ button to select
PRIM. SETUP. Then, press the F.FWD/B button.

PRIMARY SETUP

> SELECT LANGUAGE

AUTO PROGRAMMING
CH MEMORY REVIEW
VOLUME BAR [ON]
SET CLOCK

SELECT KL CHOOSE B
TO END PRESS EXIT

> PRIM. SETUP

VCR PROGRAM
VCR SETUP
CAPTION
REMINDER
BRIGHTNESS

PRESS B

2-4

• If you accidentally select Spanish
and need English on-screen displays
and menus:

1) Press the MENU button.

2) Press the PLAY/o button or the
STOP/p button to select PREPARA­CION, then press the F.FWD/B
button.

3) Press the PLAY/o button or the
STOP/p button to select SELEC­CION IDIOMA, then press the
F.FWD/B button.

4) Press the PLAY/o button or the
STOP/p button to select ENGLISH.

5) Press the STATUS/EXIT button.

Helpful Hint

1

5

EJECT

MENU

SLEEP/

WAKE UP

CH. VOL.

POWER

STATUS/EXIT

1 2 3

4 5 6

7 8 9

0

REC

/OTR

PLAY

REW

F.FWD

STOP

MUTE

SPEED

MEMORY

TRACKING

CLEAR

ALT.CH

PAUSE

/STILL

10 Automatic Channel Setup

Although the TV/VCR may automatically memorize the channels
you receive when you turn it on for the first time, you may set up
channels again by following the steps below.

1

Press the MENU button.

2

Press the PLAY/▲ button or the STOP/▼ button to select
PRIM. SETUP, then press the F.FWD/B button.

PRIMARY SETUP

> SELECT LANGUAGE

AUTO PROGRAMMING
CH MEMORY REVIEW
VOLUME BAR [ON]
SET CLOCK

SELECT KL CHOOSE B
TO END PRESS EXIT

3

Press the PLAY/▲ button or the STOP/▼ button to select
AUTO PROGRAMMING, then press the F.FWD/B button.

AUTO CH PROGRAMMING ... will appear on the screen. The
TV/VCR distinguishes between TV channels and cable channels auto­matically, and the TV/VCR will memorize its available channels.

• Line Input mode will always be
channel 00. You cannot delete it.

• You can not select AUTO PRO­GRAMMING at step 3 if you are in
Line Input mode.

Helpful Hints

4

Wait for a few minutes. When setup is complete, CHANNELS

ARE SET will appear on the screen. Then the programming of the
lowest channel number will appear on the screen. Now, when you
press the CH(annel) o/p buttons, you will scan only through
channels you receive. You can still select non-memorized channels
using the Number buttons.

4

Wait for the TV/VCR to set up
channels.

1

2-3

> PRIM. SETUP

VCR PROGRAM
VCR SETUP
CAPTION
REMINDER
BRIGHTNESS

PRESS B

EJECT

MENU

SLEEP/

WAKE UP

CH. VOL.

POWER

STATUS/EXIT

1 2 3

4 5 6

7 8 9

0

REC
/OTR

PLAY

REW

F.FWD

STOP

MUTE

SPEED

MEMORY

TRACKING

CLEAR

ALT.CH

PAUSE

/STILL

Automatic Channel Setup (cont’d) 11

4

Press the F.FWD/B button or the REW(ind)/{ button to
select SAVED (to add that channel) or DELETED (to
delete that channel).

Repeat steps 3-4 to add or delete other channels.

5

Press the STATUS/EXIT button.

Programming of the channel you added or deleted will appear.

3

Press the CH(annel) o/p buttons or the Number buttons
to select the channel you want to add or delete.

• To review the memorized channels,
follow these steps.

1) Press the MENU button.

2) Press the PLAY/▲ button or the
STOP/▼ button to select PRIM.
SETUP. Press the F.FWD/B button.

3) Press the PLAY/▲ button or the
STOP/▼ button to select
CH MEMORY REVIEW. Press the
F.FWD/B button. A list of
programmed channels will appear on
the screen.

4) If all the programmed channels
don’t fit on the screen, press the
F.FWD/B button. If you do not press
the F.FWD/B button within 10
seconds, the remaining channels will
appear on the screen. (If there are
no remaining channels, the previous
menu will appear.) Or press the
REW(ind)/{ button to see the
previous screen of channels.

5) Press the STATUS/EXIT button
once or twice.

Helpful Hint

1

Press the MENU button.

2

Press the PLAY/o button or the STOP/p button to select
CHANNEL.

TO ADJUST PRESS { / B
CH23

> CHANNEL

SMARTLOCK
REVIEW
EXIT
PRIM. SETUP
VCR PROGRAM

SAVED

TO ADJUST PRESS { / B
CH123

> CHANNEL

SMARTLOCK
REVIEW
EXIT
PRIM. SETUP
VCR PROGRAM

SAVED

1

2,4

3

5

Adding/Deleting Channels

If your channel lineup changes, you may want to add newly avail­able channels or remove channels that are no longer available in
your area. You can use the CH(annel) o/p buttons to scroll
through only the available channels. To add or delete channels
from the TV/VCR’s memory, follow these steps.

> PRIM. SETUP

VCR PROGRAM
VCR SETUP
CAPTION
REMINDER
BRIGHTNESS

PRESS B

EJECT

MENU

SLEEP/

WAKE UP

CH. VOL.

POWER

STATUS/EXIT

1 2 3

4 5 6

7 8 9

0

REC

/OTR

PLAY

REW

F.FWD

STOP

MUTE

SPEED

MEMORY

TRACKING

CLEAR

ALT.CH

PAUSE

/STILL

12 Setting the Clock

• Entries that do not match the
TV/VCR’s calendar will cause a
question mark (?) to appear on the
screen.

• To make corrections while you are
setting the clock, press the CLEAR
button until the space for the num­ber you want to correct is flashing.
Then enter the correct number.

Helpful Hints

There are three ways to set the clock: Manually, with Automatic
PBS Channel Selection, or with Manual PBS Channel Selection.
With manual clock setting, you tell the TV/VCR the current time.
With Automatic or Manual PBS Channel Selection, the TV/VCR
gets the time from your local PBS station.
If you use either Manual PBS Channel Selection or Automatic PBS
Channel Selection, follow the steps on page 19 to have the
TV/VCR maintain the clock according to your Time Zone.

Cable Box users must set the clock manually.

To set the clock manually, follow the steps on pages 12-13. To set
the clock using Automatic PBS Channel Selection, follow the steps
on pages 14-15. To set the clock using Manual PBS Channel
Selection, follow the steps on pages 16-17.
Before you begin, make sure:

● You have connected and turned on the TV/VCR. Details are on

pages six-eight.

● Channels are set. Details are on page 10.

● You make each entry within 60 seconds of the previous entry.

Manual Clock Setting

1

Press the MENU button.

2

Press the PLAY/▲ button or the STOP/▼ button to select
PRIM. SETUP. Then, press the F.FWD/B button.

PRIMARY SETUP

> SELECT LANGUAGE

AUTO PROGRAMMING
CH MEMORY REVIEW
VOLUME BAR [ON]
SET CLOCK

SELECT KL CHOOSE B
TO END PRESS EXIT

> PRIM. SETUP

VCR PROGRAM
VCR SETUP
CAPTION
REMINDER
BRIGHTNESS

PRESS B

SET CLOCK

> AUTO CLOCK [ON]

SET MANUAL CLOCK
DAYLIGHT SVG.TIME [ON]
SET TIME ZONE

[AUTO]

TO CONTINUE PRESS MENU
SELECT KL CHOOSE B

TO END PRESS EXIT

3

Press the PLAY/▲ button or the STOP/▼ button to select
SET CLOCK. Then, press the F.FWD/B button.

2-3

1

EJECT

MENU

SLEEP/

WAKE UP

CH. VOL.

POWER

STATUS/EXIT

1 2 3

4 5 6

7 8 9

0

REC
/OTR

PLAY

REW

F.FWD

STOP

MUTE

CLEAR

ALT.CH

PAUSE

/STILL

SPEED

MEMORY

TRACKING

Setting the Clock (cont’d) 13

5

Press two Number buttons for the hour(s) and two
Number buttons for the minute(s). Then press 1 for AM
or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.

SET MANUAL CLOCK

TIME 09 : 30 PM

MONTH – – / – – / – – – –

TO CORRECT PRESS CLEAR
TO END PRESS EXIT

6

Press two Number buttons for the month, two Number
buttons for the day, and two Number buttons for the
year. For example, for July 1, 2001, press 07, 01, 01. The day of

the week will appear automatically.

7

Press the STATUS/EXIT button.

SET MANUAL CLOCK

TIME 09 : 30 PM
DATE 07 / 01 / 2001

SUNDAY

TO CORRECT PRESS CLEAR
TO END PRESS EXIT

4

Press the PLAY/o button or the STOP/p button to select
SET MANUAL CLOCK, then press the F.FWD/B button.

SET MANUAL CLOCK

TIME – – : – –
DATE – – / – – / – – – –

TO END PRESS EXIT

5-67

4

EJECT

MENU

SLEEP/

WAKE UP

CH. VOL.

POWER

STATUS/EXIT

1 2 3

4 5 6

7 8 9

0

REC
/OTR

PLAY

REW

F.FWD

STOP

MUTE

SPEED

MEMORY

TRACKING

CLEAR

ALT.CH

PAUSE

/STILL

14 Setting the Clock (cont’d)

Automatic PBS Channel Selection

4

If ON appears beside AUTO CLOCK, press the MENU
button.
If OFF appears beside AUTO CLOCK, press the PLAY/o
button or the STOP/p button to select AUTO CLOCK,
then press the F.FWD/B button so that ON appears to the
right of AUTO CLOCK. Then, press the MENU button.

1

Press the MENU button.

2

Press the PLAY/▲ button or the STOP/▼ button to select
PRIM. SETUP. Then, press the F.FWD/B button.

PRIMARY SETUP

> SELECT LANGUAGE

AUTO PROGRAMMING
CH MEMORY REVIEW
VOLUME BAR [ON]
SET CLOCK

SELECT KL CHOOSE B
TO END PRESS EXIT

3

Press the PLAY/▲ button or the STOP/▼ button to select
SET CLOCK. Then, press the F.FWD/B button.

2-4

AUTO CLOCK
AUTO CLOCK USES
PBS CHANNEL DATA

> SET PBS CH. AUTO

SET PBS CH. MANUAL

SELECT KL CHOOSE B
TO END PRESS EXIT

> PRIM. SETUP

VCR PROGRAM
VCR SETUP
CAPTION
REMINDER
BRIGHTNESS

PRESS B

1

4

SET CLOCK

> AUTO CLOCK [ON]

SET MANUAL CLOCK
DAYLIGHT SVG.TIME [ON]
SET TIME ZONE

[AUTO]

TO CONTINUE PRESS MENU
SELECT KL CHOOSE B

TO END PRESS EXIT

EJECT

MENU

SLEEP/

WAKE UP

CH. VOL.

POWER

STATUS/EXIT

1 2 3

4 5 6

7 8 9

0

REC

/OTR

PLAY

REW

F.FWD

STOP

MUTE

SPEED

MEMORY

TRACKING

CLEAR

ALT.CH

PAUSE

/STILL

Setting the Clock (cont’d) 15

7

When the TV/VCR finds the PBS channel, the time will
appear on the screen. Press the STATUS/EXIT button.

6

NOW SEARCHING flashes on the TV/VCR screen.

● If CANNOT FIND CLOCK DATA flashes on the TV/VCR

screen, you will be prompted to turn off the TV/VCR.
Turn off the TV/VCR. Leave it off for several minutes. When

you turn on the TV/VCR again, the clock will be set.

• To display the time on the TV/VCR
screen, press the STATUS/EXIT but­ton. Details are on page 26.

• You cannot use the AUTO CLOCK
feature if you don’t receive a PBS
channel that carries a time signal in
your area. Set the clock manually.

Helpful Hints

5

Press the PLAY/▲ button or the STOP/▼ button to select
SET PBS CH. AUTO. Then, press the F.FWD/B button.

SET AUTO CLOCK

TIME – – : – –
DATE – – / – – / – – – –
NOW SEARCHING

TO END PRESS EXIT

SET AUTO CLOCK

TIME 06 : 30 PM
DATE 07 / 01 / 2001

SUNDAY

TO END PRESS EXIT

SET AUTO CLOCK

TIME – – : – –
DATE – – / – – / – – – –

CANNOT FIND CLOCK DATA
TO END PRESS EXIT

6

Wait for the TV/VCR to find
the time.

7

5

EJECT

MENU

SLEEP/

WAKE UP

CH. VOL.

POWER

STATUS/EXIT

1 2 3

4 5 6

7 8 9

0

REC
/OTR

PLAY

REW

F.FWD

STOP

MUTE

SPEED

MEMORY

TRACKING

CLEAR

ALT.CH

PAUSE

/STILL

16 Setting the Clock (cont’d)

Manual PBS Channel Selection

4

If ON appears beside AUTO CLOCK, press the MENU
button.
If OFF appears beside AUTO CLOCK, press the PLAY/o
button or the STOP/p button to select AUTO CLOCK,
then press the F.FWD/B button so that ON appears to the
right of AUTO CLOCK. Then, press the MENU button.

1

Press the MENU button.

2

Press the PLAY/▲ button or the STOP/▼ button to select
PRIM. SETUP. Then, press the F.FWD/B button.

PRIMARY SETUP

> SELECT LANGUAGE

AUTO PROGRAMMING
CH MEMORY REVIEW
VOLUME BAR [ON]
SET CLOCK

SELECT KL CHOOSE B
TO END PRESS EXIT

AUTO CLOCK
AUTO CLOCK USES
PBS CHANNEL DATA

> SET PBS CH. AUTO

SET PBS CH. MANUAL

SELECT KL CHOOSE B
TO END PRESS EXIT

> PRIM. SETUP

VCR PROGRAM
VCR SETUP
CAPTION
REMINDER
BRIGHTNESS

PRESS B

3

Press the PLAY/▲ button or the STOP/▼ button to select
SET CLOCK. Then, press the F.FWD/B button.

2-41

4

SET CLOCK

> AUTO CLOCK [ON]

SET MANUAL CLOCK
DAYLIGHT SVG.TIME [ON]
SET TIME ZONE

[AUTO]

TO CONTINUE PRESS MENU
SELECT KL CHOOSE B

TO END PRESS EXIT

EJECT

MENU

POWER

STATUS/EXIT

CLEAR

1 2 3

4 5 6

7 8 9

SLEEP/

WAKE UP

REC

/OTR

REW

CH. VOL.

TRACKING

0

PLAY

STOP

MUTE

SPEED

MEMORY

F.FWD

ALT.CH

PAUSE

/STILL

Setting the Clock (cont’d) 17

8

When the TV/VCR finds the clock data, the time will
appear on the screen. Press the STATUS/EXIT button.

6

Use the Number buttons to select your PBS station.

● If CANNOT FIND CLOCK DATA flashes on the

TV/VCR screen and you know another PBS channel,
press the PLAY/▲ button or the STOP/▼ button to
choose SELECT NEW PBS CH. Then, press the
F.FWD/B button. Repeat step 6.

● If CANNOT FIND CLOCK DATA flashes on the

TV/VCR screen and you do not know another channel,
press the PLAY/▲ button or the STOP/▼ button to
select SET PBS CH. AUTO. Then, press the F.FWD/B
button. The TV/VCR will search for the PBS channel automati-

cally.

• If the TV/VCR finds the PBS channel, the time will appear on
the screen.

• If the TV/VCR does not find the PBS channel, you will be
prompted to turn off the TV/VCR. Leave it off for several min­utes. When you turn on the TV/VCR again, the time will be set.

AUTO CLOCK (PBS) CH 02

TIME – – : – –
DATE – – / – – / – – – –

SELECT CHANNEL NUMBER
TO END PRESS EXIT

AUTO CLOCK (PBS) CH 12

TIME 06 : 30 PM
DATE 07 / 01 / 2001

SUNDAY

TO END PRESS EXIT

7

NOW SEARCHING flashes on the TV/VCR screen.

AUTO CLOCK (PBS) CH 12

TIME – – : – –
DATE – – / – – / – – – –
NOW SEARCHING

TO END PRESS EXIT

7

• If you have an Antenna hookup, you
may select channels 2-69 at step 6.
If you have a cable connection, you
may select channels 1-125 at step

6. Details about available memo­rized channels are on page 11.

• To display the time on the TV/VCR
screen, press the STATUS/EXIT but­ton. Details are on page 26.

Helpful Hints

Wait for the TV/VCR to
find the time.

5

Press the PLAY/▲ button or the STOP/▼ button to
select SET PBS CH. MANUAL. Then, press the F.FWD/B
button.

6

5

8

EJECT

MENU

SLEEP/

WAKE UP

CH. VOL.

POWER

STATUS/EXIT

1 2 3

4 5 6

7 8 9

REC
/OTR

TRACKING

REW

0

PLAY

STOP

MUTE

SPEED

MEMORY

F.FWD

CLEAR

ALT.CH

PAUSE

/STILL

18 Daylight-Savings Time

4

Press the PLAY/▲ button or the STOP/▼ button to select
DAYLIGHT SVG.TIME. Then, press the F.FWD/B button
so that ON or OFF appears beside DAYLIGHT SVG.
TIME (Daylight Savings Time).

5

Press the STATUS/EXIT button.

1

Press the MENU button.

2

Press the PLAY/▲ button or the STOP/▼ button to select
PRIM. SETUP. Then, press the F.FWD/B button.

PRIMARY SETUP

> SELECT LANGUAGE

AUTO PROGRAMMING
CH MEMORY REVIEW
VOLUME BAR [ON]
SET CLOCK

SELECT KL CHOOSE B
TO END PRESS EXIT

3

Press the PLAY/▲ button or the STOP/▼ button to select
SET CLOCK. Then, press the F.FWD/B button.

When the Daylight-Savings Time feature is ON, the TV/VCR clock
will automatically move forward one hour on the first Sunday in
April and move back one hour on the last Sunday in October.
To turn Daylight-Savings Time ON or OFF, follow the steps
below.

> PRIM. SETUP

VCR PROGRAM
VCR SETUP
CAPTION
REMINDER
BRIGHTNESS

PRESS B

2-4

1

5

SET CLOCK

> AUTO CLOCK [ON]

SET MANUAL CLOCK
DAYLIGHT SVG.TIME [ON]
SET TIME ZONE

[AUTO]

TO CONTINUE PRESS MENU
SELECT KL CHOOSE B

TO END PRESS EXIT

EJECT

MENU

POWER

STATUS/EXIT

CLEAR

1 2 3

4 5 6

7 8 9

SLEEP/

WAKE UP

REC
/OTR

REW

CH. VOL.

TRACKING

0

PLAY

STOP

MUTE

SPEED

MEMORY

F.FWD

ALT.CH

PAUSE

/STILL