Philips CC5060 User Manual

PHILIPS

£norelco

Kids
Hair Clipper

CC5060

Rechargeable
Cordless/Cord

Register your product and get support at

www.philips.com/norelco

ENGLISH

IMPORTANT

SAFETY

INSTRUCTIONS

When using an electrical appliance, basic safety
precautions should always be followed, including
the following:

Read all instructions before using this

appliance.

DANGER

To reduce the risk of electric shock:

1. Do not reach for a clipper that has hllen into

water. Unplug immediately.

2. This appliance and accessories (cape, scissors,
brush, comb and pouch) are NOT toys.The
appliance is an electric hair clipper. Keep the
appliance out of reach of young children.

3. Do not use while bathing or in a shower.

4. Do not place or store clipper where it can
foil or be pulled into a tub or sink. Do not
place in or drop into water or other liquid.

5. Always unplug this clipper from the electrical
outlet immediately after using, except when
clipper is (re)charging.

6. Unplug clipper before cleaning.

WARNING

To reduce the risk of burns, fire, electric
shock or injury to persons:

1. Close supervision is necessary when

this appliance and accessories (cape, scissors,
brush, comb and pouch) is used by. on, or
near children or invalids.

2. Use this clipper and accessories (cape,
scissors, brush, comb and pouch) for its
intended household use as described in
this manual. Do not use attachments not
recommended by Philips Electronics North
America Corporation.

3. Never operate this clipper if it has a
damaged cord or plug, if it is not working
properly, if it has been dropped, damaged, or
dropped into virater. For assistance calT

1.866-243.3050.

4. Do not rinse or immerse the clipper handle
in water or any other liquid.

5. Keep the clipper, cord and any attachments
away from heated surfaces.

6. Never drop or insert any object into any
opening.

7. Do not operate, charge or plug in clipper
outdoors or where aerosol (spray) products
arc being used or where oxygen is being
administered.

8. Always check cutters, cutting unit and combs
before using the clipper. Do not use the
clipper if cutters, cutting unit or combs are
damaged, as injury may occur.

9. Always attach plug to clipper first, then to
outlet To disconnect, turn clipper OFF. then
remove plug from outlet

10. To prevent possible damage to the cord, do

not wrap cord around the clipper.

11. Never put clipper in direct sunlight or store
at a temperature above 140°F.

12. This clipper is for use on human hair only.

Do not use this clipper for any other
purpose.

13. Always store your clipper, attachments and
power plug in a moisture-free area. Make
sure the cord is disconnected from the
clipper.

SAVETHESE

INSTRUCTIONS

IMPORTANT: The power plug contains
a transformer. Do not cut off the power
plug to replace it with another plug as this

will cause a hazardous condition.

Registration

Congratulations on your purchase and
welcome to Philips Norelco!

To fully benefit from the support that
Philips Norelco offers, register your
product at

Put It To The Test

Like many new products, your Philips Norelco Kids

Hair Qipper may take a little getting used to. If you
are usif^ an electric Clipper for the first time, or if
you’ve been using a different brand, lake tfie time to
acquaint yourself with your new Hair Oipper.

Your Kids Hair Oipper comes with an instructional

DVD to give you tips and instructions on how to
cut your child’s hair and how to create different

hair^es.

www.phitips.com/norelco

Put your new Hair Qipper to the test. We guarantee

precise, professional results or Philips Norelco will

refund you the full purchase price as long as the

request is received within 45 days of purchase.

Features

A Large Comb

6 Cleaning Brush
C Styling Comb
D Scissors
E Cape
F Pouch
G Appliance Plug
H Adaptor
I Charging Light

J On/c5ff Button

K Cutting Unit
L Hair Length Selector
M Small Comb
N Adaptor Cover

Full Two-Year Warranty
4S-Day Money-Back Guarantee

To Charge/Rccharge

I Fully charge Clipper before using for the first

time, after non-use for a long period of time or
when the green charging light turns orange.

¥ Charging or recharging at temperatures below

40’F or higher than 95'F adversely affects
lifespan of the battery.

I Do not charge Clipper in a pouch.
I Always unplug Clipper from the elearical outlet

immediately after use, except when Clipper is
(re)charging.

a

Be certain Clipper is OFF.

Q Open the adaptor cover and insert the

adaptor directly into the Clipper (fig. 1) and
plug the appliance plug into any 120V AC
outlet Use only the cord provided.

I An adaptor plug may be necessary for

cord usage in some foreign countries. Use
an attachment plug adaptor of the proper
configuration for power outlet

a

After a few moments, the green Charging

Light on the appliance will blink to indicate

the Clipper is charging (fig. 2).

I It will take approximately 8 hours to fully

charge the Clipper for a cordless clipping
time of up to 45 minutes.

a After the Clipper is fully charged, the green

Charging Light will light up continuously.

B Disconnect the cord and unplug from

electrical outlet

Corded Hair Clipping

D Open the adaptor cover and insert the

adaptor provided to Clipper and plug
Clipper into electrical outlet (fig. 1).

B Turn Clipper ON by pressing the ON/OFF

Button once (fig. 3) and begin clipping.

B Turn Clipper OFF and unplug.

Cordless Hair Clipping

D Charge according to directions. Unplug

Clipper from outlet and remove cord.

B Turn Clipper ON by pressing the ON/OFF

Button once (hg. 3) and begin clipping.

B If the charge runs low while clipping, the

green Charging Ught will turn orange.
The Clipper still contains enough power for
approximately 15 minutes of cordless clipping.

□ If the motor starts to run slowly, simply

connect cord provided to Clipper and oudet

to continue clipping.

Hair Clipping

I Use diis Clipper for its intended household

use as described in this manual.

I Make sure that the appliance is fully charged

before you start clipping hair.

I Before you start clipping, make sure that the

head of the person whose hair you are cutting
is at the same level as your chest so that all
parts of his/her head are clearly visible and

within easy reach.
I Only use the appliance on clean, dry hair.
k Do not use on wet hair.
I Before you begin.comb the hair in the direction

of grov^ (fig. 4).
I To achieve optimal clipping results, always move

the appliance slowly through the hair against

the direction of hair grovtoh.

TIP: For viiuol hair dipping instructions, please
refer to the DVD included with your Hair
Oipper Of go to www.philtps.com/noreko.

Clipping with small or large comb

n Be certain Clipper is OFF.
B Select the comb attachment-The remaining

hair length after clipping is indicated on the
sides of each comb (fig. S).

Small comb: 1/8 - 7/8 in. (3-21 mm)

- Large comb: 1 - 1 3/4 in. (24-42mm)

B Slide the selected comb into the guiding

grooves on both sides of Clipper and push
until you hear it ‘click’ into place (fig. 6).

Make sure ^ comb attachment locks properly
into position.

□ Press the Hair Length Selector (1) and slide

it to Uie desired setting (2) (fig. 7).

B The setting indications on the sides of the

comb show the selected setting.

When you are clipping for the first time, start at
the maxinxim clipping length setting (7/8 in/21 mm
or I 3/4 iny42mm) of the small or large comb to
familiarize yourself wiUi the appliance and prevent
accidentaify tnrnmmg hairs too short. As you
become familiar with the settings, adjust the Hair
Length Selector to desired thnnming length.

□ Make sure that the flat part of the comb is

always in full contact with the scalp to obtain
an even result.

B Since all hairs do not grow in the same

direction, move the appliance slowly over the
crown from different directions (i.e. upwards,
downwards and across) to achieve an even
result.

Q Always move the appliance against the

direction of hair growth.

a Make overlapping passes over the head to

ensure that all hair that should be cut has
been cuL

EE For best results with curly, sparse or long

hair, use the styling comb to guide the hair
towards the Clipper.

ED Turn the Clipper off regularly during clipping

and remove the hair comb to blow and/or
shake out hair that has accumulated.

> REMEMBER;You must reset the hair length

selector back to your desired setting every

time you replace the hair clipping comb on the

appliance.

T/P:Wrrte down the settings you hove used to create

a certain hairstyle as a reminder for future clipping
sessions.

The Fade

I This cut allows you to achieve a smooth

transition from longer hair on top of the
head to shorter hair on the back and sides
of the head.

□ Slide the large comb into the guiding grooves

on both sides of Clipper and push until you
hear it 'click' into place (fig. 6).

B Press the Hair Lengdi Selector (1) and slide

it to the maximum setting (2) of 1 3/4 ini
42 mm (fig. 7).

B Clip the desired areas of the head.

n Then choose a shorter setting and cut all

parts of the head except the top where you
want the hair to be longer.

B Repeat until all hairs have the desired length.

Cutting over Styling Comb or Fingers

I This technique can be used to obtain hair

lengths over 1 3/4 ini42 mm.

n Remove the hair comb attachment by

pressing the Hair Length Selector (1) and
sliding the comb off the Clipper (2) (fig. 8).

Never Dull off a comb bv grasping the flexible too

portion Always pull off by ihe bouom p.irt of

attachment.

B Comb a small section of hair upwards.
B Lift the hair with the styling comb and hold it

between your fingers.

The amount of hair you wish to cut should extend
beyond your fingers.

□ Cut the hair extending from the fingers

or comb.

B Continue this procedure, working from the

front to the back of the head.

□ Comb hair often to remove trimmed hair

and to check for uneven areas.

Contouring without a comb attachment

Remove the hair comb if you arc:
I Defining hair lines

i Trimming nape of neck

I Removing single, unwanted hairs

C'i’yfu! '.vH?n you ,|iQ clipping Without ..■ v.)

attachment as when the Qipoer is tumeo on it
will remove every hair it touches.

□ 8e certain Clipper is in the OFF position.

B Remove the hair comb attachment by

pressing the Hair Length Seleaor (1) and
sliding the comb off the Clipper (2) (fig. 8).

Never Du') off .1 comb bv grjsping flexible Iqd.

portion, AKvavs pull oH bv the bottom part of

aufl&hineni

B To contour the hairline around the ears,

comb the hair ends over the ears.

□ Tilt the Clipper in such a way that only

one edge of the cutter blades touches the
hair ends when you shape the contours
around the ears.

Only cut the hair ends. The hairline should be
close to the ear

B To contour the nape of the neck or

sideburns, turn the Clipper and hold it with
the cutter blades pointing downwards.

□ Move the Clipper slowly and smoothly

following the natural hairline.

Cleaning

I Clean the attachments after each use.

¥ Always switch Clipper OFF. unplug and remove

power supply cord from Clipper before

cleaning.

I Do not use compressed air. abrasive cleaning

agents, scourers or liquids such as alcohol,

benzene, bleach or acetone to clean the

Clipper and attachments.

> Never clean, replace or remove Clipper

attachments with motor ON.

I Never rinse or immerse the Clipper handle in

water or any other liquid.

I Do not apply pressure to cutters.
I Do not touch cutters with hard objects as this

may damage them.

I Use a soft, dry cloth to clean Clipper handle.

During Use:

¥ If cut hairs have accumulated in the comb

area, remove hairs by shaking, blowing or

using cleaning brush provided. Remember to

adjust the clipping length back to your selected
setting where you replace the comb on Clipper.

After Each Use:

o

Make sure the Clipper is switched OFF

and disconnected from the electrical outlet

B Remove the hair comb attachment by

pressing the Hair Length Selector (1) and
sliding the comb off the Clipper (2) (fig. 8).

B Push the center top end of the cutter

blade upwards with your thumb until it
opens (fig. 9).

□ Clean the cutting unit with the cleaning brush

supplied (fig. 10).

B Clean the inside of the Clipper with the

brush supplied (fig. 11).

□ Clean the handle, combs and the adaptor

with the cleaning brush supplied or with
a dry cloth.

B Close the cutting unit until it'clicks’ into

place.

RcpIacingThe Cutting Unit

l! - daniAgtxj oi wc •

• i.'ont.nuo using the CliDCX^f Replace s

immedtatelv.

D Open the cutting unit (frg. 9).

B Remove the old cutting unit by pulling it

upwards and then puli off the Clipper.

B Place the notch of ^e new cutting unit into

the slot.

□ Push the cutting unit back onto the Clipper

until you hear a ‘click*.

Th^s .ChppcLhj^ nQ.QL>>er usct>serYiccdbje Ddf:is^
For iissistjnco c.ili 1-800-2-13-3050.

Storage

I Be sure Clipper is turned OFF. Remove cord

from outlet and Clipper before storing in a
safe, dry location where it will not be crushed,
banged, or subject to damage.

I Do not wrap cord around Clipper when

storing.

I Store cord in a safe location where it will not

be cut or damaged.

I Do not place or store Clipper where

it can fall or be pulled into a tub or sink, water
or other liquid while plugged in.

Assistance

For assistance, call toll free:
1-800-243-3050

or visit our website:
www.phiiips.com/norelco

Information is available 24 hours a day.
7 days a week

4222 002 8028 2

Full Two-Year War ranty

n«tpt El«Kircr<f NorOt Софо^пол wttnm o>Kh new ЕЫр1
NcKTko product Model C0040 (exccpc cuiterv jnd conbi) 4|wnt
de<Kti n mMt'Ub or могЪлигнЬф for » penod Ы t*ro >««rt from the
d<te of pi«thue. tnd »fftn to nptr or tfpUce *rf de*ectr^ piodjC
wxhout chjrpe

IMPORTANT: Thn wjirjnty doei not cover dimite reitAre

MuOeni. miHoe or <Urte. Udc Ы retsc<t№>e eve. the of nr
jtuctvnent not provided v«h the product orimv Ы pirn or wt^>n(
the product to inv tMt the sper4r * Uve o< truulharued
repUcement pertv wil vod thn warrere>

PHILIPS ELECTRONICS NORTH AMERICA CORPORATION
WILL NOT PAY FOR WARRANTY SERVICE PERFORMED 8Y
A NON-AUTHORIZED REPAIR SERVICE ANO WILL NOT

REIMBURSE THE CONSUMER FOR DAMAGE RESULTING FROM
WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED

REPAIR SERVICE.

NO RESPONSIBiUTY IS ASSUMED FOR ANY SPECIAL.

INCIDENTAL OR CONSEQUENTIAL DAMAGES.

•ГЧ order to obtun wjrranry iCTMce. umpl^ SO ’ > or>v'
noretco or ий I-800-24)'X60 fixr ■ -‘^nce к n «Mgsntcd thM (»

joor preceebort ^ return vh^rrenti of product tv reured mitt

•eurwre prepPdi Otiraae occtermf durins thpment n »oi covered tv
tin Wiirr]ót> NOTE: ocher умггагеу. wrnten or ora*, a Ajthorved
IV FYulpi ElectrorKi North Amereu CorporatenTMwurrarvy^.--.
you ipec^ leBil nfKi jnd you me|r fuse other r^jfib wNch very
fiom tute to itite. Sorrw tut« do not cRorr the ехскмп cr Uttuten
of rKder'tif or coraequentui dinusei to the dove exduon jrtd

- •'ri rn()f not фр1|Г lojou.

*Re«d encioied гпягмсмгп ctreRiK
Muruljctured for

i'Apt Coceumer LFeAyte
A Омюл o< ЕЫрс Eteevonct North A/nene» Corporation

I too Suwwr Street 5 th floor. Sumford, CT 06SOS-5125

(Jp jyrreel Oft»» producid ГЛ'-, .•'I:»*»«*
i«ni ktfdbyLhderwnterVUberWrec'nL

NereteH Í ":#«rnjlra0fnurt </r*,ij-r—.. ,

Nerih Aftwei Cerportoc".
PHt..rC , j.ntenrd Тг»с1Р1»а otrair-'.Ae PN« fv-.»—--kj NV

0 200» M ilpv ttet»u 4C\ North Wrerea CorporAen A i Rip n * -.med

PHILIPS

^NOnELCO

45-DAY

MONEY-BACK

GUARANTEE

If you are not ^illy satisfied with your Philips
Norelco Hair Clipper, send the product back

along with dated sales receipt and we'll refund
you the full purchase price.

The Clipper must be shipped prepaid by

insured moll. Insurance prepaid, and have
the original sales receipt, indicoting purchose

price and the date of purchase, enclosed. We

cannot be responsible for lost maif.The Clipper
must be postmarked no later than 45 days
after the date of purchase. Philips Norelco
reserves the right to verify the purchase price
of the Clipper and limit refunds not to exceed
suggested retail price.

To obtain Money-Back Guarantee Return
Authorization Form, call 1-800-243-3050 for
assistance. Please allow 4-6 weeks for delivery
of check.