Philips BTA212X-600E, BTA212X-600D, BTA212X-800F, BTA212X-800E, BTA212X-600F Datasheet
Philips Semiconductors Objective specification
Three quadrant triacs BTA212X series D, E and F
guaranteed commutation
GENERAL DESCRIPTION QUICK REFERENCE DATA
Passivated guaranteed commutation SYMBOL PARAMETER MAX. MAX. UNIT
triacs in a full pack, plastic envelope
intended for use in motor control circuits BTA212X- 600D -
or with other highly inductive loads. BTA212X- 600E 800E
These devices balance the BTA212X- 600F 800F
requirements of commutation V
performance and gate sensitivity. The voltages
"sensitivegate"Eseries and"logiclevel" I
Dseriesare intended for interfacingwith I
low power drivers, including micro current
DRM
T(RMS)
TSM
controllers.
PINNING - SOT186A PIN CONFIGURATION SYMBOL
Repetitive peak off-state 600 800 V
RMS on-state current 12 12 A
Non-repetitive peak on-state 95 95 A
PIN DESCRIPTION
case
1 main terminal 1
2 main terminal 2
3 gate
case isolated
123
G
LIMITING VALUES
Limiting values in accordance with the Absolute Maximum System (IEC 134).
SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT
-600 -800
V
DRM
I
T(RMS)
I
TSM
Repetitive peak off-state - 600
voltages
RMS on-state current full sine wave; - 12 A
Ths ≤ 56 ˚C
Non-repetitive peak full sine wave;
on-state current Tj = 25 ˚C prior to
surge
t = 20 ms - 95 A
I2tI
2
t for fusing t = 10 ms - 45 A2s
t = 16.7 ms - 105 A
dIT/dt Repetitive rate of rise of ITM = 20 A; IG = 0.2 A; 100 A/µs
on-state current after dIG/dt = 0.2 A/µs
triggering
I
V
P
P
T
T
GM
GM
GM
G(AV)
stg
j
Peak gate current - 2 A
Peak gate voltage - 5 V
Peak gate power - 5 W
Average gate power over any 20 ms - 0.5 W
period
Storage temperature -40 150 ˚C
Operating junction - 125 ˚C
temperature
1
800 V
T1T2
1 Although not recommended, off-state voltages up to 800V may be applied without damage, but the triac may
switch to the on-state. The rate of rise of current should not exceed 3 A/µs.
October 1999 1 Rev 1.200
Philips Semiconductors Objective specification
Three quadrant triacs BTA212X series D, E and F
guaranteed commutation
ISOLATION LIMITING VALUE & CHARACTERISTIC
Ths = 25 ˚C unless otherwise specified
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
V
isol
C
isol
THERMAL RESISTANCES
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
R
th j-hs
R
th j-a
R.M.S. isolation voltage from all f = 50-60 Hz; sinusoidal - - 2500 V
three terminals to external waveform;
heatsink R.H. ≤ 65% ; clean and dustfree
Capacitance from T2 to external f = 1 MHz - 10 - pF
heatsink
Thermal resistance full or half cycle
junction to heatsink with heatsink compound - - 4.0 K/W
without heatsink compound - - 5.5 K/W
Thermal resistance in free air - 55 - K/W
junction to ambient
STATIC CHARACTERISTICS
Tj = 25 ˚C unless otherwise stated
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
BTA212X- ...D ...E ...F
I
GT
I
L
I
H
V
T
V
GT
I
D
Gate trigger current
Latching current VD = 12 V; IGT = 0.1 A
Holding current VD = 12 V; IGT = 0.1 A - - 15 25 30 mA
On-state voltage IT = 17 A - 1.3 1.6 V
Gate trigger voltage VD = 12 V; IT = 0.1 A - 0.7 1.5 V
Off-state leakage current VD = V
2
VD = 12 V; IT = 0.1 A
T2+ G+ - - 5 10 25 mA
T2+ G- - - 5 10 25 mA
T2- G- - - 5 10 25 mA
T2+ G+ - - 15 20 25 mA
T2+ G- - - 25 30 40 mA
T2- G- - - 25 30 40 mA
VD = 400 V; IT = 0.1 A; 0.25 0.4 - V
Tj = 125 ˚C
; - 0.1 0.5 mA
DRM(max)
Tj = 125 ˚C
2 Device does not trigger in the T2-, G+ quadrant.
October 1999 2 Rev 1.200
Loading...