Page 1
Register your product and get support at
www.philips.com/welcome
BT9290
4222.002.8403.1
2 3 4
ENGLISH
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benet from the support that Philips
5 6 7
offers, register your product at www.philips.com/
welcome.
General description (Fig. 1)
1 Precision trimming comb
2 Standard trimming comb
8 9 10
3 Turnable trimming head
4 Laser guide
5 Guiding groove for trimming comb
6 Length setting display
7 Zoom wheel for length setting
8 On/off button
9 Battery lights
11 12 13
10 Socket for small plug
11 Adapter
12 Small plug
13 Cleaning brush
14 Storage pouch
14 15 16
Important
Read this user manual carefully before you use the
appliance and save it for future reference.
1
Danger
- Keep the adapter dry (Fig. 2).
- This symbol means: Forbidden to clean under
17
18 19
a running tap.
Warning
- Check if the voltage indicated on the adapter
corresponds to the local mains voltage before
you connect the appliance.
- The adapter contains a transformer. Do not cut
20 21 22
off the adapter to replace it with another plug,
as this causes a hazardous situation.
- This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
23 24 25
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
- Keep the appliance and its cord out of the
reach of children.
- This symbol means: Forbidden to use in the
shower (Fig. 3).
26 27 28
- Warning: Do not use this appliance close to
a bathtub, shower or other containers lled
with water.
Caution
- Always check the appliance before you use it.
Do not use the appliance if any of its parts is
damaged or broken, as this may cause injury.
- Only use this appliance for its intended
purpose as shown in the user manual.
- Use, charge and store the appliance at a
temperature between 5°C and 35°C.
- Only use the adapter supplied to charge the
appliance.
- Make sure the appliance is switched off and
disconnected from the mains before you clean
it under the tap.
- If the appliance is subjected to a major change
in temperature, pressure or humidity, let the
appliance acclimatise for 30 minutes before
you use it.
- If the adapter is damaged, always have it
replaced with one of the original type in order
to avoid a hazard.
- Never use compressed air, scouring pads,
abrasivecleaning agents or aggressive liquids such
as petrol or acetone to clean the appliance.
Compliance with standards
- The appliance can be safely cleaned under the
tap (Fig. 4).
- This symbol means: Suitable to be cleaned
under a running tap.
- This Philips appliance complies with all
applicable standards and regulations regarding
exposure to electromagnetic elds.
Class 1 laser product
- The product contains a class 1 laser guide
which complies with IEC60825-1 (Fig. 5).
- To avoid all risks, point the laser beam away
from your eyes and do not stare directly into
the laser beam (Fig. 6).
Preparing for use
Charging
Charge the appliance fully before you use it for the
rst time and after a long period of disuse.
Charging takes about 60 minutes if the appliance is
completely empty.
1 Make sure the appliance is switched off and
the laser guide is in ‘off’ position.
2 Insert the small plug into the appliance and
put the adapter in the wall socket (Fig. 7).
, First the bottom battery light ashes orange
and white alternately (Fig. 8).
, After about 3 minutes the bottom battery
light ashes white only. At this point the
battery contains enough energy for one
cordless trimming session (Fig. 9).
Page 2
, When the charging process continues, more
lights start ashing to show that the charge
level of the battery increases.
, When the appliance is fully charged, all
battery lights light up solid white (Fig. 10).
If the appliance is still connected to the mains
when it is fully charged, the battery lights go out
after 30 minutes.
Battery low and battery empty signals
, When the battery is almost empty, the
bottom battery light starts ashing orange.
When you switch off the appliance, the
bottom battery light continues to ash
orange for a few seconds (Fig. 11).
, The battery light at the bottom of the
appliance ashes orange at a higher frequency
when the battery is empty and if you:
- press the on/off button
- turn the zoom wheel
- activate the laser guide
Corded trimming
You can also operate the appliance from the mains.
1 Insert the small plug into the socket of the
appliance (Fig. 7).
2 Put the adapter in a wall socket.
3 Press the on/off button to switch on the
appliance (Fig. 12).
Using the appliance
You can use the appliance to trim facial hair (beard,
moustache and sideburns). This appliance is not
intended for trimming lower body parts or scalp hair.
Trimming with the laser guide
You can use the laser guide to dene the edges
of your beard, sideburns and moustache. The laser
guide can be used with the 32mm (1.25in) side as
well as the 15mm (0.6in) side of the trimming head.
Note: The laser guide can only be used when you trim
without comb.
Note: Although the light from the laser guide is not
harmful to the eyes, we advise you not to stare into
the light and to avoid shining the light into your
eyes (Fig. 6).
1 Press the on/off button to switch on the
appliance (Fig. 12).
2 To trim with the laser guide, press the top of
the laser guide to switch it on (Fig. 13).
, The laser guide pops up and its light shines
over the top of the trimming head.
Note: If you trim with the laser guide, make sure you
push the laser guide to ‘off ’ position before you turn
the trimming head. You may damage the laser guide
if you try to turn the trimming head while the laser
guide is still popped up (Fig. 14).
3 Start trimming where you want to dene the
edges of your beard and use the laser guide
to guide you during trimming (Fig. 15).
Tip: Hold the appliance so that the laser light shines
exactly on the edge you want to trim and then place
the trimming head on your skin.
4 When you are nished, press the on/off
button to switch off the appliance (Fig. 12).
Tip: When the motor of the appliance is not
operating, the laser guide switches off automatically
within 3 minutes. In the 3 minutes before the
automatic switch-off of the laser guide, you can use
the laser guide to check if the contours of your beard
are symmetrical or straight.
5 Push down the top of the laser guide to lock
it in ‘off’ position (‘click’) (Fig. 16).
Trimming without comb
If you trim without comb, your hair is cut off close
to the skin. The trimming head has a 32mm (1.25in)
side and a 15mm (0.6in) side. The 15mm (0.6in) side
of the trimming head allows more precise styling
and contouring than the 32mm (1.25in) side.
1 If one of the combs is still on the trimming
head, pull it off (Fig. 17).
Never pull at the exible top of the comb. Always
pull at the sides.
2 Turn the trimming head until the side you
want to use points to the front of the
appliance (Fig. 14).
3 Press the on/off button to switch on the
appliance (Fig. 12).
4 Hold the appliance in the position that is
most convenient for the area you want
to trim and make strokes in the desired
direction.
Tip: For a comfortable trim close to your skin, place
the at side of the trimming head against your skin
and make strokes in the desired direction.
5 When you are nished, press the on/off
button to switch off the appliance.
Trimming with comb
The appliance comes with two combs: a standard
comb and a precision comb. These combs keep the
trimming head at a certain distance from your skin.
This distance determines the remaining hair length
and can be adjusted by turning the zoom wheel.
- Use the standard comb to trim your
beard (Fig. 18).
- Use the precision comb to trim hard-to-reach
areas, for instance under your nose (Fig. 19).
1 Slide the comb into the guiding grooves on
both sides of the appliance (‘click’) (Fig. 20).
Note: The comb does not t on the trimming head
when the 15mm (0.6in) side is pointing towards the
front of the appliance. If this is the case, turn the
trimming head before you slide the comb onto the
trimming head.
2 Turn the zoom wheel to select a length
setting (Fig. 21).
- The length setting selected lights up on the
front of the appliance.
- You can select a length from 0.4mm to 7mm
(see table in section ‘Length settings’ below).
3 Press the on/off button to switch on the
appliance (Fig. 12).
4 To trim your beard, move the trimming
comb through the hair slowly.
5 When you are nished, press the on/off
button to switch off the appliance (Fig. 12).
Tips
- Always make sure that the tips of the trimming
comb point in the direction in which you move
the appliance.
- Make sure that the at part of the trimming
comb is always in full contact with the skin to
obtain an even hair length result.
- Since hair grows in different directions, you
need to move the appliance in different
directions (upward, downward or across).
- Trimming is easier when skin and hair are dr y.
Length settings
mm
0.4 0.6 0.8 1.0 1.2
1.4 1.6 1.8 2.0 2.5
3.0 3.5 4.0 4.5 5.0
6.0 7.0
Cleaning and maintenance
Clean the appliance after every use.
Never use compressed air, scouring pads, abrasive
cleaning agents or aggressive liquids such as
petrol or acetone to clean the appliance.
Note: The trimming head does not need any lubrication.
Cleaning the appliance and the combs
1 Switch off the appliance.
2 Pull the comb off the trimming head (Fig. 17).
3 Clean the trimming head under the tap with
lukewarm water or clean it with the cleaning
brush supplied (Fig. 22).
4 Clean the trimming combs under the tap
or clean them with the cleaning brush
supplied (Fig. 23).
Tip: To make sure that the appliance is dry before
you store it in the pouch, let it dry in a well-ventilated
room with the laser popped up.
Cleaning the trimming head connector
Note: Make sure you clean the trimming head
connector at least once every three months.
1 Switch off the appliance.
2 Pull the comb off the trimming head (Fig. 17).
3 Pull the trimming head off the
appliance (Fig. 24).
Note: To prevent damage to the laser guide, put the
laser guide in ‘off ’ position before you remove the
trimming head.
4 Clean the trimming head connector with the
cleaning brush supplied (Fig. 25).
5 Clean the inside of the trimming head with
the cleaning brush supplied (Fig. 26).
6 After cleaning, put the trimming head back
onto the appliance.
Ordering accessories
To buy accessories or spare parts, visit
www.shop.philips.com/service or go to your
Philips dealer. You can also contact the Philips
Consumer Care Centre in your country (see the
worldwide guarantee leaet for contact details).
Guarantee and support
If you need information or support, please visit the
Philips website at www.philips.com/support or
read the worldwide guarantee leaet.
Page 3
Environment
- Do not throw away the appliance with the
normal household waste at the end of its life,
but hand it in at an ofcial collection point for
recycling. By doing this, you help to preserve
the environment (Fig. 27).
- The built-in rechargeable battery contains
substances that may pollute the environment.
Always remove the battery before you discard and
hand in the appliance at an ofcial collection point.
Dispose of the battery at an ofcial collection
point for batteries. If you have trouble removing
the battery, you can also take the appliance to a
Philips service centre. The staff of this centre will
remove the battery for you and will dispose of it
in an environmentally safe way. (Fig. 28)
Frequently asked questions
If you cannot nd the answer to your question
below, visit www.philips.com/support for a list
of frequently asked questions or contact the
Consumer Care Centre in your country.
Question Answer
Is the laser light
harmful to my
eyes?
No, it is not. The appliance has
been thoroughly tested for
home use. Nevertheless, we
advise you not to stare into the
light and to avoid shining the
light directly into your eyes.
I cannot turn
the trimming
head. Why?
Can I clean
this appliance
under a
You have to push the laser
guide to ‘off ’ position before
you can turn the trimming head.
The appliance is watertight and
you can clean it under a running
tap with lukewarm water.
running tap?
Tip: To prevent condensation on
the laser window of the laser
guide, we advise you not to rinse
the appliance under the tap.
Why doesn’t
the comb
t on the
trimming head?
The combs can only be used
when the wide side of the
trimming head points towards
the front of the appliance. If the
comb does not t:
Question Answer
1) you may have tried to t
it onto the trimming head
when the narrow side of the
trimming head points towards
the front of the appliance. Turn
the trimming head to normal
trimming position and then
slide the comb onto it.
2) The laser guide is still on. To
trim with one of the combs,
you rst have to push the laser
guide to ‘off ’ position.
What is the
difference
between the
combs?
The standard comb is most
suitable for trimming your
beard to an even length. The
precision comb is especially
suitable for trimming hardto-reach areas, for instance
beneath your nose.
Why can’t I
see the laser
light?
The laser guide is in ‘off ’
position. Switch on the laser
guide by pressing the top of
the laser guide.
You switched off the appliance
with the laser guide still
popped up. After 3 minutes,
the laser guide switches off
automatically. Switch on the
laser guide by pressing the top
of the laser guide.
You are using the appliance in a
room or area where the light is
very bright. Move to a room or
area where the light is less bright.
Why can’t I
see the hairs
when I use the
laser guide?
You are probably using the
appliance in a room or area that
is too dark. Switch on the light
in the room or go to a room or
area where there is more light.
How long
does it take
to charge
the appliance
for just one
trimming
session?
This appliance has a quickcharge function. When the
appliance starts charging, the
bottom light ashes orange
and white alternately.
After 3 minutes the bottom
light stops ashing orange and
only ashes white. At this point,
the battery contains enough
energy for one trimming session.
Question Answer
Why don’t I
see a straight
uninterrupted
laser line?
The laser light from the laser
guide may be interrupted
because the laser window of
the laser guide is dirty. Pop up
the laser guide and wipe the
laser window clean with a cloth.
There is condensation behind
the laser window. Pop up the
laser guide and let it dry in a
well-ventilated room. The laser
guide switches off automatically
after 3min.
You did not assemble the
trimming head correctly. Push
down the trimming head to
make sure it is assembled
correctly.
简体中文
简介
感谢您的惠顾，欢迎光临飞利浦！为了您能充
分享受飞利浦提供的支持，请在
www.philips.com/welcome 上注册您的产品。
基本说明 (图 1)
1 精细修剪梳
2 标准修剪梳
3 可转动修剪刀头
4 激光导引
5 修剪梳导槽
6 长度设定显示屏
7 长度设定缩放轮
8 开/关按钮
9 电池指示灯
10 小插头的转换插座
11 适配器
12 小插头
13 清洁刷
14 存储袋
注意事项
使用本产品之前，请仔细阅读本使用说明书，
并妥善保管以备日后参考。
危险
- 保持适配器干燥。 (图 2)
- 警告符号注释：禁止用在打开的水龙头下
进行清洗。
警告
- 在将本产品连接电源前，务必检查当地的
电压是否与电源适配器所标电压一致。
- 电源软线不能更换，如果软线损坏，此器
具(电源适配器）应废弃。
- 电源适配器内含有一个变压器。切勿自行
更换插头，否则将导致严重后果。
- 肢体不健全、精神有障碍及缺乏相关经验
和知识的人（包括儿童）必须在监护人的
监督及指导下使用。
- 将产品及其线缆放在儿童接触不到的地
方。
- 警告符号注释：禁止在洗澡或淋浴时使
用。(图 3)
- 警告：不要在盛水的浴缸、淋浴、洗脸盆
或其他器皿附近使用本器具。
注意
- 使用前，请务必检查产品。一旦产品的任
何部件损坏或损毁，请勿再使用产品，
否则可能对人体造成伤害。
- 只能将本产品用于用户手册中所示的原定
用途。
- 必须在 5 摄氏度至 35 摄氏度之间的温度
下使用、存放和为本产品充电。
- 为产品充电，须用随产品提供的电源适
配器。
- 清洁本产品之前，请确保产品电源关闭并
已将电源插头拔出。
- 如果产品的使用温度、气压或湿度方面改
变较大，应在使用之前让产品适应 30 分
钟。
- 如果适配器已损坏，则务必更换原装型号
适配器，以免发生危险。
- 切勿使用压缩气体、钢丝绒、研磨性清洁
剂或腐蚀性液体（例如汽油或丙酮）来清
洁产品。
符合标准
- 本产品可放心在水龙头下清洗。 (图 4)
- 符号注释：适合用在打开的水龙头下进行
清洗。
- 本飞利浦产品符合所有有关暴露于电磁场
的适用标准和法规。
1类激光产品
- 本产品包含符合 GB7247.1 要求的 1 级激
光导引。 (图 5)
- 为避免所有风险，请将激光束远离您的双
眼，切勿直视激光束。 (图 6)
使用准备
充电
首次使用前或长时间不用之后，请为产品充
满电。
如果本产品电能完全耗尽，请充电大约
60 分钟。
Page 4
1 确保产品已关闭，且激光导引位于
“关闭”位置。
2 将小插头插入产品，然后将适配器插入电
源插座。 (图 7)
, 首先底部电池指示灯会交替闪烁橙色和白
色。 (图 8)
, 大约 3 分钟后，底部电池指示灯仅呈白色
闪烁。此时电池包含的电量足够完成一次
不接电源的修剪过程。 (图 9)
, 充电过程继续时，更多指示灯开始闪烁以
显示电池充电量增加。
, 产品充满电时，所有充电指示灯会呈白色
亮起。 (图 10)
如果产品在充满电时仍然连接电源，则电池指
示灯将在 30 分钟后熄灭。
电池电量不足和电池耗尽信号
, 当电池电量即将耗尽时，底部电池指示灯
开始闪烁橙色。关闭本产品后，底部充电
指示灯将持续闪烁橙色几秒钟。 (图 11)
, 当电池电量耗尽且您执行以下操作时，
本产品底部的充电指示灯将以较高频率闪
烁橙色：
- 按开/关按钮
- 旋转缩放轮
- 激活激光导引
接电修剪
您也可以接电操作产品。
1 将小插头插入产品插座。 (图 7)
2 将适配器插入电源插座。
3 按开/关按钮启动产品。 (图 12)
使用本产品
您可以使用本产品修剪面部须发（胡须、须髭
和鬓角）。本产品不得用于修剪身体下部毛发
或头发。
使用激光导引进行修剪
您可以使用激光导引确定胡须、鬓角和须髭
的边缘。激光导引可与修剪刀头的 32 毫米
（1.25 英寸）一侧和 15 毫米（0.6 英寸）
一侧一起使用。
注意： 激光导引只能在不使用修剪梳修剪时
使用。
注意： 尽管激光导引的光线对眼睛无害，
但我们建议您不要直视光线并且避免光线照射
您的双眼。 (图 6)
1 按开/关按钮启动产品。 (图 12)
2 要使用激光导引进行修剪，请按下激光导
引顶部将其打开。 (图 13)
, 激光导引将弹出，其光线会照在修剪刀头
顶部。
注意： 如果您使用激光导引进行修剪，在旋
转修剪刀头之前，请确保将激光导引推至
“关闭”位置。如果您在激光导引仍弹出时旋
转修剪刀头，可能会损坏激光导引。 (图 14)
3 在您想确定胡须边缘的位置开始修剪，
并且在修剪过程中使用激光导引指导您修
剪。 (图 15)
提示： 握持产品以确保激光能正好照在您想修
剪的边缘，然后将修剪刀头放在您的皮肤上。
4 完成剃须后，按开/关按钮关闭产品。
(图 12)
提示： 当产品的马达不工作时，激光导引会
在 3 分钟内自动关闭。在激光导引自动关闭前
的 3 分钟内，您可以使用激光导引检查您的胡
须轮廓是否对称或笔直。
5 下推激光导引的顶部，将其锁在“关闭”
位置（可听到“咔哒”一声）。 (图 16)
修剪（无修剪梳）
如果您不使用修剪梳进行修剪，则会贴近皮
肤修剪您的毛发。修剪刀头有 32 毫米（1.25
英寸）一侧和 15 毫米（0.6 英寸）一侧。修
剪刀头的 15 毫米（0.6 英寸）一侧比 32 毫
米（1.25 英寸）一侧的造型和轮廓效果更精
确。
1 如果某个修剪梳仍在修剪刀头上，请将其
拔出。 (图 17)
切勿拉动修剪梳的活动顶部。必须拉拔侧面。
2 旋转修剪刀头，直至您要使用的一侧指向
产品正面。 (图 14)
3 按开/关按钮启动产品。 (图 12)
4 在最方便修剪的位置握住产品，按所需的
方向来回移动。
提示： 为了获得舒适的贴肤修剪，请将修剪
刀头平坦的一侧紧贴皮肤放置，然后按所需的
方向来回移动。
5 完成剃须后，按开/关按钮关闭产品。
修剪（有修剪梳）
本产品随附有两个梳齿：标准梳齿和精密梳
齿。这些梳齿可使修剪刀头与皮肤保持一定的
距离。此距离可确定剩余的毛发长度，并且可
通过转动缩放轮来调整。
- 使用标准梳齿修剪胡须。 (图 18)
- 使用精密梳齿修剪难以触及的部位，
例如鼻子下方。 (图 19)
1 将梳齿滑入产品两侧的导槽中（可听到
“咔哒”一声）。 (图 20)
注意： 当修剪刀头的 15 毫米（0.6 英寸）一
侧指向产品正面时，梳齿无法装入修剪刀头。
如果发生这种情况，请先转动修剪刀头，
然后再将梳齿滑入修剪刀头。
2 旋转缩放轮可选择长度设定。 (图 21)
- 选择的长度设定会在产品正面亮起。
- 您可以选择 0.4 毫米至 7 毫米之间的长度
（请参见以下“长度设定”章节中的表）
。
3 按开/关按钮启动产品。 (图 12)
4 要修剪胡须，请将修剪梳在毛发上缓缓移
动。
5 完成剃须后，按开/关按钮关闭产品。
(图 12)
提示
- 确保修剪梳齿方向与产品移动方向一致。
- 确保修剪梳的扁平部分始终完全接触皮
肤，以获得均匀的头发长度。
- 由于头发会朝不同方向生长，您必须沿着
不同方向（向上/向下或交叉）移动本产
品。
- 皮肤和毛发干燥时修剪更容易。
长度设定
毫米
0.4 0.6 0.8 1.0 1.2
1.4 1.6 1.8 2.0 2.5
3.0 3.5 4.0 4.5 5.0
6.0 7.0
清洁和保养
每次使用后都应立即清洁产品。
切勿使用压缩气体、钢丝绒、研磨性清洁剂或
腐蚀性液体（例如汽油或丙酮）来清洁产品。
注意： 修剪刀头不需要任何润滑。
清洁产品和修剪梳
1 关闭产品。
2 将修剪梳从修剪刀头中拉出。 (图 17)
3 在温水水龙头下清洗修剪刀头或用随附的
清洁刷进行清洁。 (图 22)
4 在水龙头下清洗修剪梳或用随附的清洁刷
进行清洁。 (图 23)
提示： 为了确保将产品放入软袋之前保持干
燥，请将其放在通风良好的房间内干燥，同时
弹出激光导引。
清洁修剪刀头连接器
注意： 确保至少每三个月清洁一次修剪刀头。
1 关闭产品。
2 将修剪梳从修剪刀头中拉出。 (图 17)
3 将修剪刀头从产品中拉出。 (图 24)
注意： 为防止损坏激光导引，请将激光导引
置于“关闭”位置，然后取下修剪刀头。
4 用随附的清洁刷清洁修剪刀头接头。
(图 25)
5 用随附的清洁刷清洁修剪刀头内侧。
(图 26)
6 清洁后，将修剪刀头放回产品上。
订购附件
要购买附件和备件，请访问
www.shop.philips.com/service 或 请联系飞利
浦经销商。您也可以联系您所在国家/地区的
飞利浦客户服务中心（联系详情，请参阅全球
保修卡）。
保修和支持
如果您需要信息或支持，请访问飞利浦网站
www.philips.com/support 或阅读全球保修卡。
环保
- 弃置产品时，请不要将其与一般生活垃圾
堆放在一起；应将其交给官方指定的回收
点。这样做有利于环保。 (图 27)
- 内置充电电池含有可能会污染环境的物
质。丢弃产品时，一定要将电池取出，并
将产品送到官方指定的回收站。到官方指
定的电池回收站处理电池。如果您在取出
电池时遇到问题，您也可以将产品送至飞
利浦维修中心。维修中心的员工会帮您取
出电池，并以环保的方式处理它。 (图 28)
常见问题
如果您无法在下方找到问题的答案，请访问
www.philips.com/support 查阅常见问题列
表，
或联系您所在国家/地区的飞利浦客户服务中
心。
Page 5
问题 回答
激光对我
的眼睛有
害吗？
无害。本产品已经过全面测试，
适合家庭使用。但是我们仍建议
您不要直视光线并且避免光线直
射您的眼睛。
我无法旋
转修剪刀
您必须在旋转修剪刀头前将激光
导引推至“关闭”位置。
头，为什
么？
我能否在
水龙头下
本产品防水，您可以在温水水龙
头下清洗。
清洁本产
品？
提示：为了防止激光导引的激光
窗口出现冷凝现象，我们建议您
不要在水龙头下冲洗本产品。
为什么修
剪梳无法
装入修剪
修剪梳只能在修剪刀头的宽面朝
向产品正面时使用。如果修剪梳
无法装入：
刀头？
1) 您可能试图在修剪刀头的窄面
朝向产品正面时将修剪梳装入修
剪刀头。请将修剪刀头旋转至正
常修剪位置，然后将修剪梳滑入。
2) 激光导引仍然打开。要使用其
中一个修剪梳修剪，您必须先将
激光导引推至“关闭”位置。
梳齿之间
有什么不
同？
为什么我
看不到激
光？
标准梳齿最适合将胡须修剪至平
均长度。精密梳齿特别适合修剪
难以触及的部位，例如鼻子下方。
激光导引位于“关闭”位置。
按下激光导引顶部可打开激光
导引。
您在激光导引仍弹出时关闭了产
品。3 分钟后，激光导引会自动
关闭。按下激光导引顶部可打开
激光导引。
您在光线非常明亮的房间或区域
中使用产品。移至光线较暗的房
间或区域。
为什么使
用激光导
引时我看
您可能在太暗的房间或区域中使
用本产品。打开房内的灯，或移
至光线较亮的房间或区域。
不到毛
发？
问题 回答
产品只需
充电多长
时间即可
完成一次
修剪过
程？
为什么我
看不到笔
直的不间
断激光？
本产品具有快速充电功能。产品
开始充电时，底部的指示灯会交
替闪烁橙色和白色。3 分钟后，
底部电池指示灯停止闪烁橙色，
仅呈白色闪烁。此时电池包含的
电量足够完成一次修剪过程。
激光导引中的激光可能会因激光
导引的激光窗口变脏而中断。弹
出激光导引，然后用布将激光窗
口擦拭干净。
激光窗口后面有冷凝现象。弹出
激光导引，然后让激光导引在通
风良好的房间干燥。激光导引将
在 3 分钟后自动关闭。
您没有正确组装修剪刀头。向下
推动修剪刀头，以确保其正确
安装。
01/08/2013
Loading...