Philips BSL722 Cold User Manual

BSL722 COLD

Installation Instructions

EMERGENCY LED DRIVER

WHEN USING ELECTRICAL EQUIPMENT, BASIC

! IMPORTANT SAFEGUARDS !

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. To prevent high voltage from being present on yellow & yellow/black output leads prior to installation,
converter connector must be open. Do not join converter connector to the fuseholder until installation is
complete and AC power is supplied to the emergency driver.

2. This product is for use with an LED lighting load and supplies up to 23.1 W of power at a rated current of
700 mA with a voltage between 28.0 VDC and 33.0 VDC in emergency mode for a minimum of 90 minutes.

3. Make sure all connections are in accordance with the National Electrical Code, Canadian Electrical Code and
any local regulations.

4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and converter
connector of the emergency driver before servicing.

5. This emergency driver is for factory installation only.

6. This product is suitable for damp locations where the ambient driver temperature is -20°C minimum, +60°C
maximum. Product is not suitable for heated air outlets and wet or hazardous locations.

7. An unswitched AC power source is required (120 through 277 VAC, 50 or 60 Hz).

8. Do not install near gas or electric heaters.

9. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

10. Do not use this product for other than intended use.

11. Servicing should be performed by qualied service personnel.

SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED, INCLUDING THE FOLLOWING:

NRTL/C

SAVE THESE INSTRUCTIONS

Ni - Cd

THIS PRODUCT INCLUDES RECHARGEABLE NICKEL-CADMIUM BATTERIES.

THE BATTERIES MUST BE RECYCLED OR DISPOSED OF PROPERLY.

10/13/14

© Philips Emergency Lighting

236 Mt. Pleasant Rd. • Collierville, TN USA 38017-2752 • Tech Support 888-263-4638 • Fax [phone] • www.philips.com/philips

70100084

INSTALLATION

WARNING: TO PREVENT HIGH VOLTAGE FROM BEING PRESENT ON YELLOW & YELLOW/BLACK
OUTPUT LEADS PRIOR TO INSTALLATION, CONVERTER CONNECTOR MUST BE OPEN. DO NOT
JOIN CONVERTER CONNECTOR TO THE FUSEHOLDER UNTIL INSTALLATION IS COMPLETE AND
AC POWER IS SUPPLIED TO THE EMERGENCY DRIVER.

NOTE: Make sure the necessary branch circuit wiring is available. An unswitched source of

power is required. The emergency driver must be fed from the same branch circuit as
the AC driver.

STEP #1

INSTALLING THE EMERGENCY DRIVER

> Disconnect AC power from the xture.

> Refer to Illustration 1 below to install the emergency driver and batteries. Make electrical connections in

accordance with the National Electrical Code and any local regulations. Note: This is only an example of
one possible installation.

ILLUSTRATION 1

Typical Fixture Assembly

AC/EMERGENCY

DRIVER COMPARTMENT

EMERGENCY DRIVER

AC DRIVER

BATTERY

BATTERY

LED

ASSEMBLY

BATTERY COMPARTMENTS

STEP #2

INSTALLING A TEST SWITCH

> Refer to Illustration 2 to install a typical low voltage illuminated test switch. Illustration 3 depicts the

wiring schematic of a TEST SWITCH and CHARGING INDICATOR LIGHT to the EMERGENCY DRIVER.

ILLUSTRATION 3ILLUSTRATION 2

Typical (Non-Specific) Illuminated

Test Switch

Fixture

Illuminated
Test Switch

Push to Test

CHARGING
INDICATOR

LIGHT

Wiring Schematic

NORMALLY OPEN

TEST SWITCH

BLACKBLACK

RED

BLUE

GRAY

GRAY

VIOLET (+)

BROWN (-)

EMERGENCY

DRIVER

2

CAUTION: DO NOT CONNECT THE YELLOW AND YELLOW/BLACK LEADS TOGETHER. THIS MAY
DAMAGE THE EMERGENCY DRIVER.

STEP #3

STEP #4

WIRING THE EMERGENCY DRIVER

> Connect the yellow emergency driver wire to the positive input of the emergency LED load. Next, connect the

negative output wire of the AC driver and the yellow/black emergency driver wire to the negative lead of the
emergency LED load. See wiring diagrams on the next page for unswitched, switched, and emergency-only xtures.
Contact factory for other wiring diagrams if needed.

> Connect the test switch as shown on the wiring diagrams on the next page.

> Follow the corresponding wiring diagrams to connect the remaining leads.

> After installation is complete, supply AC power to the emergency driver and join the converter connector to the

fuseholder.

EMERGENCY DRIVER QUICK CHECK AND LABELING

> For short-term testing of the emergency function, the batteries must be charged for at least one hour. The

batteries must be charged for at least 24 hours before conducting a long-term test.

>

In a readily visible location, attach the label "CAUTION: This Unit Has More Than One Power Supply Connection Point.

To Reduce The Risk Of Electric Shock, Disconnect Both The Branch Circuit-Breakers Or Fuses And Emergency Power
Supplies Before Servicing."

OPERATION

When AC power is applied, the charging indicator light is illuminated, indicating the batteries are being charged. When
power fails, the emergency driver automatically switches to emergency power, operating the emergency LED load at reduced
illumination. When AC power is restored, the emergency driver returns to the charging mode. This emergency driver will
operate an LED lighting load at a rated current of 700 mA with a voltage between 28.0 VDC and 33.0 VDC and up to 23.1 W
of output power for a minimum of 90 minutes.

MAINTENANCE

Although no routine maintenance is required to keep the emergency driver functional, it should be checked periodically to
ensure that it is working. The following schedule is recommended:

1. Visually inspect the charging indicator light monthly. It should be illuminated.

2. Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds. The LED lighting
load should operate at reduced illumination.

3. Conduct a 90-minute discharge test once a year. The emergency LED load should operate at reduced illumination
for a minimum of 90 minutes.

4. The fuse provided is only for use in the output supply circuit of the emergency driver. If the LED lighting load
fails to operate in the emergency mode, inspect the fuse and replace if necessary.

CAUTION: To replace fuse, disconnect fuseholder from converter connector and both switched and unswitched

AC power from the fixture. Remove the old fuse from the fuseholder and replace with a new 2A, 32 VDC rated,
non-time delay blade fuse. Supply AC power to fixture and reconnect converter connector to the fuseholder.
Charging indicator light should be illuminated. Contact manufacturer for fuse replacement.

! REFER ANY SERVICING INDICATED BY THESE CHECKS TO QUALIFIED PERSONNEL !

3

EMERGENCY DRIVER AND AC DRIVER MUST BE FED FROM THE SAME BRANCH CIRCUIT

HOT

COMMON

WHITE/RED

WHITE

WHITE

EMERGENCY

DRIVER

RED

WHITE

(120V THROUGH 277V)

AC DRIVER

RED/WHITEBLACK

BLACK

WHITE/BLACK

BLACK

BLUE

RED/WHITE

BLACK

FUSEHOLDER/

CONVERTER
CONNECTOR

YELLOW(+)

YELLOW/BLACK(-)

LED ASSEMBLY

BLUE(-)

RED(+)

EMERGENCY

LED LOAD

BLUE

RED

WHITE

YELL/RED

BLUE/ORG

BLUE/ORG

YELL/RED

YELL/RED

YELL/RED

VIOLET

BROWN

GRAY

GRAY

BLACK

BLUE

RED

NORMALLY

OPEN ITS

BLACK

BATTERY

2

BATTERY

1

HARNESS CONNECTOR

HARNESS CONNECTOR

HARNESS CONNECTOR

HARNESS CONNECTOR

HOT

COMMON

WHITE/RED

WHITE

WHITE

EMERGENCY

DRIVER

(120V THROUGH 277V)

AC DRIVER

RED/WHITEBLACK

BLACK

WHITE/BLACK

BLACK

RED/WHITE

BLACK

FUSEHOLDER/

CONVERTER
CONNECTOR

YELLOW(+)

YELLOW/BLACK(-)

LED ASSEMBLY

BLUE(-)

RED(+)

EMERGENCY

LED LOAD

WALL SWITCH

RED

WHITE

BATTERY

2

BLUE

BLUE

RED

WHITE

BATTERY

1

YELL/RED

BLUE/ORG

HARNESS CONNECTOR

HARNESS CONNECTOR

HARNESS CONNECTOR

HARNESS CONNECTOR

BLUE/ORG

YELL/RED

YELL/RED

YELL/RED

VIOLET

BROWN

GRAY

GRAY

BLACK

BLUE

RED

NORMALLY

OPEN ITS

BLACK

YELLOW(+)

YELLOW/BLACK(-)

EMERGENCY

LED LOAD

HOT

COMMON

WHITE/RED

WHITE

EMERGENCY

DRIVER

(120V THROUGH 277V)

RED/WHITEBLACK

BLACK

WHITE/BLACK

RED/WHITE

BLACK

FUSEHOLDER/

CONVERTER
CONNECTOR

(CAP UNUSED LEAD)

(CAP UNUSED LEAD)

RED

WHITE

BLUE

BLUE

RED

WHITE

YELL/RED

BLUE/ORG

BLUE/ORG

YELL/RED

YELL/RED

YELL/RED

VIOLET

BROWN

GRAY

GRAY

BLACK

BLUE

RED

NORMALLY

OPEN ITS

BLACK

BATTERY

2

BATTERY

1

HARNESS CONNECTOR

HARNESS CONNECTOR

HARNESS CONNECTOR

HARNESS CONNECTOR

TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER DRIVERS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS.

CAUTION: DO NOT CONNECT THE YELLOW AND YELLOW/BLACK LEADS TOGETHER. THIS MAY
DAMAGE THE EMERGENCY DRIVER.

WIRING DIAGRAM FOR UNSWITCHED FIXTURE

WIRING DIAGRAM FOR SWITCHED FIXTURE

WIRING DIAGRAM FOR EMERGENCY-ONLY FIXTURE

4