Philips Brilliance 200P3M User Manual

Philips 200P3M/200P3G Electronic User's Manual

file:///D|/K1/english/200p3mg/index.htm [1/3/2003 3:34:16 PM]

Safety and Troubleshooting Information

Safety Precautions and Maintenance • Installation Locations • FAQs • Troubleshooting • Regulatory Information • Other Related Information

Safety precautions and maintenance

WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards.

Read and follow these instructions when connecting and using your computer monitor:

Unplug the monitor if you are not going to use it for an extensive period of time.● Unplug the monitor if you need to clean it with a slightly damp cloth. The screen many be wiped with

a dry cloth when the power is off. However, never use alcohol, solvents or ammonia-based liquids.

●

Consult a service technician if the monitor does not operate normally when you have followed the instructions in this manual.

●

The casing cover should be opened only by qualified service personnel.● Keep the monitor out of direct sunlight and away from stoves or any other heat source.● Remove any object that could fall into the vents or prevent proper cooling of the monitor’s electronics.● Do not block the ventilation holes on the cabinet.● Keep the monitor dry. To avoid electric shock, do not expose it to rain or excessive moisture.● When positioning the monitor make sure the power plug and outlet are easily accessible.● If turning off the monitor by detaching power cable or DC power cord, wait for 6 seconds before

attaching the power cable or DC power cord for normal operation.

●

To avoid the risk of shock or permanent damage to the set do not expose the monitor to rain or excessive moisture.

●

When positioning the monitor, make sure the power plug and outlet are easily accessible.● IMPORTANT: Always activate a screen saver program during your application. If a still image in high

contrast remains on the screen for an extended period of time, it may leave an 'after-image' or 'ghost image' on front of the screen. This is a well-known phenomenon that is caused by the shortcomings inherent in LCD technology. In most cases the after-image will disappear gradually over a period of time after the power has been switched off. Be aware that the after-image symptom cannot be repaired and is not covered under warranty.

●

Consult a service technician if the monitor does not operate normally when the operating instructions given in this manual have been followed.

RETURN TO TOP OF THE PAGE

Installation Locations

Avoid exposure to heat and extreme cold●

Safety & Troubleshooting

file:///D|/K1/english/200p3mg/safety/safety.htm (1 of 2) [1/3/2003 3:34:22 PM]

Do not store or use the LCD monitor in locations exposed to heat, direct sunlight or extreme cold.● Avoid moving the LCD monitor between locations with large temperature differences. Choose a site

that falls within the following temperature and humidity ranges.

Temperature: 5-35°C 41-95°F

❍

Humidity: 20-80% RH❍

●

Do not subject the LCD monitor to severe vibration or high impact conditions. Do not place the LCD monitor inside a car boot.

●

Take care not to mishandle this product by either knocking or dropping during operation or transportation.

●

Do not store or use the LCD monitor in locations where there is a high level of humidity or in dusty environments. Do not allow water or other liquids to spill on or into the LCD monitor.

●

RETURN TO TOP OF THE PAGE

Safety & Troubleshooting

file:///D|/K1/english/200p3mg/safety/safety.htm (2 of 2) [1/3/2003 3:34:22 PM]

About This Manual

About This Guide • Notational Descriptions

About This Guide

This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It describes the LCD monitor's features, setup, operation and other important information. Its contents are identical to the information in our printed version.

It includes the following sections:

Safety and Troubleshooting Information provides tips and solutions for common problems as well as

other related information you may need.

●

About This Electronic User's Manual gives an overview of information included, along with notation icon descriptions and other documentation for your reference.

●

Product Information gives an overview of the monitor's features as well as the technical specifications

for this monitor.

●

Installing Your Monitor describes the initial setup process and gives an overview of how to use the

monitor.

●

On-Screen Display provides information on adjusting the settings on your monitor.● Customer Care and Warranty contains a list of worldwide Philips Consumer Information Centers

along with help desk phone numbers and information on the warranty applicable to your product.

●

Glossary defines technical terms.● Download and Print Option transfers this entire manual to your hard drive for easy reference.●

RETURN TO TOP OF THE PAGE

Notational Descriptions

The following subsections describe notational conventions used in this document.

Notes, Cautions and Warnings

Throughout this guide blocks of text may be accompanied by an icon and printed in bold or italic type. These blocks contain notes, cautions or warnings. They are used as follows:

NOTE: This icon indicates important information and tips that help you make better use of your computer system.

About This Electronic User's Manual

file:///D|/K1/english/200p3mg/about/about.htm (1 of 2) [1/3/2003 3:34:24 PM]

CAUTION: This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data.

WARNING: This icon indicates the potential for bodily harm and tells you how to avoid the problem.

Some warnings may appear in alternate formats and may not be accompanied by an icon. In such cases, the specific presentation of the warning is mandated by the relevant regulatory authority.

RETURN TO TOP OF THE PAGE

part is prohibited without written consent of Philips Electronics N.V.

About This Electronic User's Manual

file:///D|/K1/english/200p3mg/about/about.htm (2 of 2) [1/3/2003 3:34:24 PM]

Product Information

Product Features • Technical Specifications • Resolution & Preset Modes • Philips Pixel Defect Policy • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views • Physical Function

Product Features

BRILLIANCE 200P3M/200P3G

20-inch color LCD monitor with excellent display performance● Multiple video input allowing displaying of DVI-I digital/ analog, VGA analog, S-Video & CVBS

Video inputs.

●

Picture-in-Picture (PIP) function for displaying both PC and video simultaneous on the screen● Embedded AC power supply● Front firing speakers with stereo 2x2W RMS stereo sound output● Advanced AUTO adjustment optimizes picture quality● Adjustable tilt and swivel function●

RETURN TO TOP OF THE PAGE

Technical Specifications*

LCD PANEL

• Type TFT LCD

• Screen size 20.1" / 51cm

• Pixel Pitch 0.255 x 0.255mm

• LCD Panel type

1600 x 1200 pixels R.G.B. vertical stripe Anti-glare polarizer, hard coated

• Effective viewing area 408 x 306 mm

• Display Colors 8 bits interface (16M colors)

SCANNING

Vertical refresh rate 56Hz-85Hz Horizontal Frequency 30kHz-94kHz (Analog input), 30kHz-92kHz(Digital input)

200P3M/200P3G Product Information

file:///D|/K1/english/200p3mg/product/product.htm (1 of 7) [1/3/2003 3:34:27 PM]

VIDEO

• Video dot rate 202 MHz

• Input impedance

- Video 75 ohm

- Sync 2K ohm

• Input signal levels 0.7 Vpp

• Sync input signal

Separate sync Composite sync

Sync on green

• Sync polarities Positive and negative

• S-Video Y input 1.0Vpp, C input 0.3Vpp, 75ohm input impedance

• CVBS Composite, 1.0Vpp, 75ohm input impedance

•Video interface

Triple input(two connectors): D-Sub(analog) and DVI-I(accepts both digital and analog) are available and user selectable S-Video & CVBS

AUDIO-IN

• Input signal level 0.7 Vpp

• Headphone out signal level

32 20+20mW

• Input signal connector 3.5mm mini jack

• Loudspeaker

4W Stereo Audio (2W/channel RMSx2, 200Hz-12kHz, 4 ohm,THD=10%)

MICROPHONE

• Sensitivity -45dB re 1V/Pa at 1kHz

• Output impedance

2.2K max.

• Directivity -5dB at 180°

• Frequency range 300Hz-3kHz

Optical characteristics

• Contrast ratio: 300 (typ.)

• Brightness:

250 cd/m2 (typ.)

• Peak contrast angle 6 o'clock

• White Chromatcity:

x: 0.281 y: 0.311 (at 9300°K) x: 0.312 y: 0.338 (at 6500°K)

200P3M/200P3G Product Information

file:///D|/K1/english/200p3mg/product/product.htm (2 of 7) [1/3/2003 3:34:27 PM]

• Viewing Angle: (C/R>10)

Upper >85° (typ.) Lower >85° (typ.) Left >85° (typ.) Right >85° (typ.)

• Response time <30ms (typ.)

* This data is subject to change without notice.

RETURN TO TOP OF THE PAGE

Resolution & Preset Modes

• Maximum

1600 x 1200 at 75Hz(analog input) 1600 x 1200 at 60Hz(digtal input)

• Recommended 1600 x 1200 at 60Hz

50 user definable modes

18 factory preset modes:

H. freq (kHz) Resolution V. freq (Hz)

31.5 640*350 70 (IBM VGA 10h)

31.5 720*400 70

31.5 640*480 60

35.0 640*480 67

37.5 640*480 75

35.2 800*600 56

37.9 800*600 60

46.9 800*600 75

49.7 832*624 75

48.4 1024*768 60

60.0 1024*768 75

69.0 1152*870 75

71.8 1152*900 76 (SUN Mode II)

63.9 1280*1024 60 80 1280*1024 75

200P3M/200P3G Product Information

file:///D|/K1/english/200p3mg/product/product.htm (3 of 7) [1/3/2003 3:34:27 PM]

91.1 1280*1024 85

75.0 1600*1200 60

93.8 1600*1200 75

RETURN TO TOP OF THE PAGE

Automatic Power Saving

If you have VESA DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will 'wake up' automatically. The following table shows the power consumption and signaling of this automatic power saving feature:

Power Management Definition

VESA Mode Video H-sync V-sync Power Used LED color

ON Active Yes Yes < 60W Green

OFF Blanked No No < 3W Amber

This monitor is ENERGY STAR® compliant. As an ENERGY STAR® Partner, PHILIPS has determined that this product meets the

ENERGY STAR

guidelines for energy efficiency.

RETURN TO TOP OF THE PAGE

Physical Specifications

• Dimension (WxHxD) 488 x 459 x220 mm (incl. Pedestal)

• Weight 10.0 Kg

• Tilt / Swivel -5° ~ 25° / + - 175°

• Power supply 100 — 240 VAC, 50/60 Hz

• Power consumption 52 W (typ.)

200P3M/200P3G Product Information

file:///D|/K1/english/200p3mg/product/product.htm (4 of 7) [1/3/2003 3:34:27 PM]

• Temperature

5° C to 35° C (operating)

-20° C to 60° C (storage)

• Relative humidity 20% to 80%

• System MTBF 50K hrs (including CCFL 40K hrs)

• Cabinet color

200P3M: Light Gray 200P3G: Black

* This data is subject to change without notice. * Resolution 1600x1200, standard size, contrast max., brightness 50%, 9300° K, full white pattern,

without audio/USB.

RETURN TO TOP OF THE PAGE

Pin Assignment

1. The digital/analog DVI-I onnector contains 29 signal contacts organized in three rows of eight contacts. Signal pin assignments are listed in the following table:

No.

Signal

Assignment

No.

Signal

Assignment

No.

Signal

Assignment

No.

Signal

Assignment

1 TMDS Data 2- 9 TMDS Data 1- 17

TMDS Data 0-

Analog Red Video Out

2 TMDS Data 2+ 10 TMDS Data 1+ 18

TMDS Data 0+

Analog Green Video Out

TMDS Data 2/4 Shield

TMDS Data 1/3 Shield

TMDS Data 0/5 Shield

Analog Blue Video Out

4 TMDS Data 4- 12 TMDS Data 3- 20

TMDS Data 5-

Analog Horizontal Sync

5 TMDS Data 4+ 13 TMDS Data 3+ 21

TMDS Data 5+

Analog Common Ground Return (Red, Green, Blue Video Out)

6 DDC Clock 14 +5V Power 22

TMDS Clock Shield

7 DDC Data 15

Ground (+5V, Analog H/V Sync)

TMDS Clock+

Analog Vertical Sync

16 Hot Plug Detect 24 TMDS Clock-

200P3M/200P3G Product Information

file:///D|/K1/english/200p3mg/product/product.htm (5 of 7) [1/3/2003 3:34:27 PM]

2. The 15-pin D-sub connector (male) of the signal cable:

No.

Assignment

No.

Assignment

1 Red video input 9 +5V 2 Green video input/SOG 10 Logic ground

3 Blue video input 11

Identical output - connected

to pin 10 4 Sense (GND) 12 Serial data line (SDA) 5 Not connected 13 H. Sync / H+V 6 Red video ground 14 V. Sync (VCLK for DDC)

7 Green video ground 15 Data clock line (SCL) 8 Blue video ground

RETURN TO TOP OF THE PAGE

Product Views

Follow the links to see various views of the monitor and its components.

Front View Product Description

RETURN TO TOP OF THE PAGE

Physical Function

200P3M/200P3G Product Information

file:///D|/K1/english/200p3mg/product/product.htm (6 of 7) [1/3/2003 3:34:27 PM]

1) Tilt

2) Swivel

RETURN TO TOP OF THE PAGE

200P3M/200P3G Product Information

file:///D|/K1/english/200p3mg/product/product.htm (7 of 7) [1/3/2003 3:34:27 PM]

Installing your LCD Monitor

Your LCD Monitor : Front View Product Description • Setting up and connecting your

monitor • VESA Standard Mounting • Getting Started • Optimizing Performance

Front View Product Description

To switch monitor's power On and Off Power LED To access OSD menu To adjust the OSD To adjust brightness of the display To adjust the OSD To adjust speakers volume

Automatically adjust the horizontal position, vertical position, phase and clock setting

To mute the audio sound MUTE LED

Video input LED, lit when CVBS or S-Video activated Signal inputs selection

PC input LED, lit when VGA or DVI activated Activated PIP (Picture in Picture) window

RETURN TO TOP OF THE PAGE

Rear View

Installing your LCD Monitor

file:///D|/K1/english/200p3mg/install/install.htm (1 of 3) [1/3/2003 3:34:30 PM]

1 CVBS video input 2 S-Video video input 3 VGA input 4 DVI-I input 5 AC power in 6 Mic out 7 Audio in 8 Audio L input 9 Audio R input

RETURN TO TOP OF THE PAGE

Optimizing Performance

For best performance, ensure that your display settings are set at 1600x1200@60Hz●

Installing your LCD Monitor

file:///D|/K1/english/200p3mg/install/install.htm (2 of 3) [1/3/2003 3:34:30 PM]

Note: You can check the current display settings by pressing the "OK" button once.

Go into the Product Information. The current display mode is shown on the item called RESOLUTION.

You can also install the Flat Panel Adjust (FP Adjust) program, a program for getting the best performance out of your monitor. This included on this CD. Step-by-step instructions are provided to guide you through the installtion process. Click on the link to know more about this program.

More about

FP_setup03.exe

●

RETURN TO TOP OF THE PAGE

Installing your LCD Monitor

file:///D|/K1/english/200p3mg/install/install.htm (3 of 3) [1/3/2003 3:34:30 PM]

On-Screen Display

Description of the On-Screen Display • The OSD Tree

Description of the On Screen Display

What is the On-Screen Display?

This is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance of the monitors directly though an on-screen instruction window. The user interface provides user-friendliness and ease-of-use when the user is operating the monitor.

Basic and simple instruction on the control keys.

When you press the

button on the front control of your monitor, the On-Screen Display (OSD) Main

Controls window will pop up and you can then start making adjustments to your monitor's various features. Use the

or the keys to make your adjustments.

RETURN TO TOP OF THE PAGE

On-Screen Display

file:///D|/K1/english/200p3mg/osd/osddesc.htm (1 of 7) [1/3/2003 3:34:34 PM]

The OSD Tree

Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on.

On-Screen Display

file:///D|/K1/english/200p3mg/osd/osddesc.htm (2 of 7) [1/3/2003 3:34:34 PM]

On-Screen Display

file:///D|/K1/english/200p3mg/osd/osddesc.htm (3 of 7) [1/3/2003 3:34:34 PM]

On-Screen Display

file:///D|/K1/english/200p3mg/osd/osddesc.htm (4 of 7) [1/3/2003 3:34:34 PM]

On-Screen Display

file:///D|/K1/english/200p3mg/osd/osddesc.htm (5 of 7) [1/3/2003 3:34:34 PM]

On-Screen Display

file:///D|/K1/english/200p3mg/osd/osddesc.htm (6 of 7) [1/3/2003 3:34:34 PM]

RETURN TO TOP OF THE PAGE

On-Screen Display

file:///D|/K1/english/200p3mg/osd/osddesc.htm (7 of 7) [1/3/2003 3:34:34 PM]

Customer Care & Warranty

PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR WARRANTY COVERAGE

WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece •

Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • Switzerland • Spain • United Kingdom

EASTERN EUROPE: Czech Republic • Hungary • Poland • Russia • Turkey LATIN AMERICA: Antilles • Argentina • Brasil • Chile • Colombia • Mexico • Paraguay • Peru

• Uruguay • Venezuela

NORTH AMERICA: Canada • USA PACIFIC: Australia • New Zealand ASIA: Bangladesh • China • Hong Kong • India • Indonesia • Japan • Korea • Malaysia •

Pakistan • Philippines • Singapore • Taiwan • Thailand

AFRICA: Morocco • South Africa MIDDLE EAST: Dubai • Egypt

Customer Care and Warranty

file:///D|/K1/english/warranty/warranty.htm [1/3/2003 3:34:36 PM]

Glossary

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Color temperature

A way of describing the color of a radiating source in terms of the temperature (in degrees Kelvin) of a black body radiating with the same dominant frequency as the source.

Most Philips monitors offer the possibility of setting the color temperature to any desired value.

RETURN TO TOP OF THE PAGE

D-SUB USB

Your monitor comes with a D-Sub cable.

Digital Visual Interface (DVI)

The Digital Visual Interface (DVI) specification provides a high-speed digital connection for visual data types that is display technology independent. The interface is primarily focused at providing a connection between a computer and its display device. The DVI specification meets the needs of all segments of the PC industry (workstation, desktop, laptop, etc.) and will enable these different segments to unite around one monitor interface specification.

The DVI interface enables:

Content to remain in the lossless digital domain from creation to consumption.1. Display technology independence.2. Plug and play through hot plug detection, EDID and DDC2B.3. Digital and Analog support in a single connector.4.

RETURN TO TOP OF THE PAGE

Glossary

file:///D|/K1/english/200p3mg/glossary/glossary.htm (1 of 4) [1/3/2003 3:34:39 PM]

Energy Star Computers Programme

An energy conservation programme launched by the US Environmental Protection Agency (EPA) with the primary aim of promoting the manufacture and marketing of energy-efficient office automation equipment. Companies joining this programme must be willing to commit themselves to manufacturing one or more products capable of going into a low -power state (< 30 W) either after a period of inactivity or after a predetermined time selected by the user.

RETURN TO TOP OF THE PAGE

LCD Liquid Crystal Display

An alphanumeric display using the unique properties of liquid crystal to form characters. The latest flat-panel displays comprise a matrix of hundreds or thousands of individual LCD cells that generate text and colorful graphics on a screen. They consume little power though they do require external lighting to make them legible to the user.

RETURN TO TOP OF THE PAGE

USB or Universal Serial Bus

A smart plug for PC peripherals. USB automatically determines resources (like driver software and bus

bandwidth) required by peripherals. USB makes necessary resources available without user intervention.

USB eliminates "case angst" -- the fear of removing the computer case to install add-on peripherals. And USB also eliminates adjustment of complicated IRQ settings when installing new peripherals.

●

USB does away with "port gridlock." Without USB, PCs are normally limited to one printer, two Com port devices (usually a mouse and modem), one Enhanced Parallel Port add-on (scanner or video camera, for example) and a joystick. More and more peripherals for multimedia computers arrive on the market every day. With USB, up to 127 devices can run simultaneously on a computer.

●

USB permits "hot plug-in." There's no need to shut down, plug in, reboot and run set-up to install peripherals. And no need to go through the reverse process to unplug a device.

●

In short, USB transforms today's "Plug-and-Pray" into true Plug-and-Play!

Hub

Glossary

file:///D|/K1/english/200p3mg/glossary/glossary.htm (2 of 4) [1/3/2003 3:34:39 PM]

+ 56 hidden pages