Philips BDP-5320-F-7 Service Manual

SERVICE MANUAL

BLU-RAY DISC PLAYER

BDP5320/F7

IMPORTANT SAFETY NOTICE

Proper service and repair is important to the safe, reliable operation of all
P&F Equipment. The service procedures recommended by P&F and
described in this service manual are effective methods of performing
service operations. Some of these service special tools should be used
when and as recommended.

It is important to note that this service manual contains various CAUTIONS
and NOTICES which should be carefully read in order to minimize the risk
of personal injury to service personnel. The possibility exists that improper
service methods may damage the equipment. It also is important to
understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE.
P&F could not possibly know, evaluate and advice the service trade of all
conceivable ways in which service might be done or of the possible
hazardous consequences of each way. Consequently, P&F has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a
service procedure or tool which is not recommended by P&F must first use
all precautions thoroughly so that neither his safety nor the safe operation
of the equipment will be jeopardized by the service method selected.

TABLE OF CONTENTS

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-1

Laser Beam Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2-1

Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3-1

Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4-1

Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5-1

How to Initialize the BLU-RAY Disc Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6-1

Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7-1

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8-1

Internet Radio (vTuner) Error Code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9-1

Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10-1

Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11-1

Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12-1

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13-1

System Control Timing Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14-1

IC Pin Function Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15-1

Lead Identifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16-1

Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17-1

Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18-1

Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19-1

Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.

SPECIFICATIONS

1-1-1 E5SK6SP

LASER BEAM SAFETY PRECAUTIONS

This BD player uses a pickup that emits a laser beam.

Do not look directly at the laser beam coming
from the pickup or allow it to strike against your
skin.

The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep
your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look directly at the laser
beam.

CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in
hazardous radiation exposure.

Drive Mechanism Assembly

Laser Beam Radiation

Laser Pickup

Turntable

Location: Inside Top of BD mechanism.

1-2-1 B2NLBSP

IMPORTANT SAFETY PRECAUTIONS

Product Safety Notice

Some electrical and mechanical parts have special
safety-related characteristics which are often not
evident from visual inspection, nor can the protection
they give necessarily be obtained by replacing them
with components rated for higher voltage, wattage,
etc. Parts that have special safety characteristics are
identified by a # on schematics and in parts lists. Use
of a substitute replacement that does not have the
same safety characteristics as the recommended
replacement part might create shock, fire, and/or other
hazards. The Product’s Safety is under review
continuously and new instructions are issued
whenever appropriate. Prior to shipment from the
factory, our products are carefully inspected to confirm
with the recognized product safety and electrical
codes of the countries in which they are to be sold.
However, in order to maintain such compliance, it is
equally important to implement the following
precautions when a set is being serviced.

Precautions during Servicing

A. Parts identified by the # symbol are critical for

safety. Replace only with part number specified.

B. In addition to safety, other parts and assemblies

are specified for conformance with regulations
applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise
blocking capacitors, and noise blocking filters, etc.

C. Use specified internal wiring. Note especially:

1) Wires covered with PVC tubing

2) Double insulated wires

3) High voltage leads

D. Use specified insulating materials for hazardous

live parts. Note especially:

1) Insulation tape

2) PVC tubing

3) Spacers

4) Insulators for transistors

E. When replacing AC primary side components

(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before
soldering.

F. Observe that the wires do not contact heat

producing parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.).

G. Check that replaced wires do not contact sharp

edges or pointed parts.

H. When a power cord has been replaced, check that

5 - 6 kg of force in any direction will not loosen it.

I. Also check areas surrounding repaired locations.
J. Be careful that foreign objects (screws, solder

droplets, etc.) do not remain inside the set.

K. When connecting or disconnecting the internal

connectors, first, disconnect the AC plug from the
AC outlet.

L. When reassembling, be sure to use the original

screws or specified screws listed in the parts list.

1-3-1 BDN_ISP

Safety Check after Servicing

Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and
wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified
values to verify compliance with safety standards.

1. Clearance Distance

When replacing primary circuit components, confirm
specified clearance distance (d) and (d’) between
soldered terminals, and between terminals and
surrounding metallic parts. (See Fig. 1)

Table 1: Ratings for selected area

Chassis or Secondary Conductor

Primary Circuit

AC Line Voltage Clearance Distance (d), (d’)

120 V

Note: This table is unofficial and for reference only. Be

sure to confirm the precise values.

≥ 3mm(d)

≥ 4mm(d’)

2. Leakage Current Test

Confirm the specified (or lower) leakage current
between B (earth ground, power cord plug prongs) and
externally exposed accessible parts (RF terminals,
antenna terminals, video and audio input and output
terminals, microphone jacks, earphone jacks, etc.) is
lower than or equal to the specified value in the table
below.

Measuring Method (Power ON):

Insert load Z between B (earth ground, power cord plug
prongs) and exposed accessible parts. Use an AC
voltmeter to measure across the terminals of load Z.
See Fig. 2 and the following table.

d' d

Exposed Accessible Part

Z

One side of

B

Power Cord Plug Prongs

Fig. 1

AC Voltmeter
(High Impedance)

Table 2: Leakage current ratings for selected areas

AC Line Voltage Load Z Leakage Current (i)

2kΩ RES.

Connected in

parallel

120 V

50kΩ RES.

Connected in

parallel

Note:This table is unofficial and for reference only. Be sure to confirm the precise values.

i≤0.7mA AC Peak

i≤2mA DC

i≤0.7mA AC Peak

i≤2mA DC

1-3-2 BDN_ISP

One side of power cord plug

prongs (B) to:

RF or

Antenna terminals

A/V Input, Output

Fig. 2

STANDARD NOTES FOR SERVICING

Circuit Board Indications

1. The output pin of the 3 pin Regulator ICs is
indicated as shown.

To p Vi ew

Out

2. For other ICs, pin 1 and every fifth pin are
indicated as shown.

Pin 1

3. The 1st pin of every male connector is indicated as
shown.

Pin 1

Input

In

Bottom View

5

10

Pb (Lead) Free Solder

When soldering, be sure to use the Pb free solder.

How to Remove / Install Flat Pack-IC

1. Removal

With Hot-Air Flat Pack-IC Desoldering Machine:

1. Prepare the hot-air flat pack-IC desoldering
machine, then apply hot air to the Flat Pack-IC
(about 5 to 6 seconds). (Fig. S-1-1)

Fig. S-1-1

Instructions for Connectors

1. When you connect or disconnect the FFC (Flexible
Foil Connector) cable, be sure to first disconnect
the AC cord.

2. FFC (Flexible Foil Connector) cable should be
inserted parallel into the connector, not at an
angle.

FFC Cable

Connector

CBA

* Be careful to avoid a short circuit.

2. Remove the flat pack-IC with tweezers while
applying the hot air.

3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)

4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)

CAUTION:

1. The Flat Pack-IC shape may differ by models. Use
an appropriate hot-air flat pack-IC desoldering
machine, whose shape matches that of the Flat
Pack-IC.

2. Do not supply hot air to the chip parts around the
flat pack-IC for over 6 seconds because damage
to the chip parts may occur. Put masking tape
around the flat pack-IC to protect other parts from
damage. (Fig. S-1-2)

1-4-1 BDN_SN

3. The flat pack-IC on the CBA is affixed with glue, so
be careful not to break or damage the foil of each
pin or the solder lands under the IC when
removing it.

With Soldering Iron:

1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)

CBA

Masking
Ta pe

Tweezers

Hot-air
Flat Pack-IC
Desoldering
Machine

Flat Pack-IC

Fig. S-1-2

Flat Pack-IC

Desoldering Braid

Soldering Iron

Fig. S-1-3

2. Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)

Sharp
Pin

Fine Tip
Soldering Iron

3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)

4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)

Fig. S-1-4

1-4-2 BDN_SN

With Iron Wire:

1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)

2. Affix the wire to a workbench or solid mounting
point, as shown in Fig. S-1-5.

3. While heating the pins using a fine tip soldering
iron or hot air blower, pull up the wire as the solder
melts so as to lift the IC leads from the CBA
contact pads as shown in Fig. S-1-5.

4. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)

5. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)

Note: When using a soldering iron, care must be

taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.

Hot Air Blower

2. Installation

1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA
so you can install a replacement flat pack-IC more
easily.

2. The “ I ” mark on the flat pack-IC indicates pin 1.
(See Fig. S-1-7.) Be sure this mark matches the
pin 1 on the PCB when positioning for installation.
Then presolder the four corners of the flat pack-IC.
(See Fig. S-1-8.)

3. Solder all pins of the flat pack-IC. Be sure that
none of the pins have solder bridges.

Example :

Pin 1 of the Flat Pack-IC
is indicated by a " " mark.

Fig. S-1-7

To Solid
Mounting Point

CBA

Tweezers

Iron Wire

Soldering Iron

Fig. S-1-5

Fine Tip
Soldering Iron

Flat Pack-IC

or

Presolder

Flat Pack-IC

CBA

Fig. S-1-8

Fig. S-1-6

1-4-3 BDN_SN

Instructions for Handling Semi­conductors

Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.

1. Ground for Human Body

Be sure to wear a grounding band (1 MΩ) that is
properly grounded to remove any static electricity that
may be charged on the body.

2. Ground for Workbench

Be sure to place a conductive sheet or copper plate
with proper grounding (1 MΩ) on the workbench or
other surface, where the semi-conductors are to be
placed. Because the static electricity charge on
clothing will not escape through the body grounding
band, be careful to avoid contacting semi-conductors
with your clothing.

<Incorrect>

<Correct>

1MΩ

CBA

Grounding Band

1MΩ

CBA

Conductive Sheet or
Copper Plate

1-4-4 BDN_SN

CABINET DISASSEMBLY INSTRUCTIONS

1. Disassembly Flowchart

This flowchart indicates the disassembly steps to gain
access to item(s) to be serviced. When reassembling,
follow the steps in reverse order. Bend, route, and
dress the cables as they were originally.

[1] Top Cover

[2] Front Unit

[6] Rear Panel

[8] BD Main CBA &
BD Mechanism Assembly

[9] AV CBA

[10] Power Supply CBA

[3] Front-A CBA

[4] Front-B CBA

[5] Front Assembly

[7] DC Fan Motor

2. Disassembly Method

ID/

Loc.

No.

[1] Top Cover D1 6(S-1) ---

[2] Front Unit D2

[3]

[4]

[5]

[6] Rear Panel D4

[7]

[8]

[9] AV CBA D6

[10]

↓

(1)

Part

Front-A
CBA

Front-B
CBA

Front
Assembly

DC Fan
Motor

BD Main
CBA & BD
Mechanism
Assembly

Power
Supply
CBA

↓

(2)

Fig.

No.

*4(L-1), *2(L-2),
*CN1004, *CN5000

D3 *2(L-3) 1

D3 *4(L-4) 1

D3 ---------- ---

(S-2), 3(S-3), (S-4),
2(S-5), *CN1005

(S-6), Fan Cover,

D4

Fan Plate

4(S-7), 2(S-8),

D5

*CN6101, *CN7101,
*CN7601

4(S-9), Desolder,
Main PCB Bracket

D6 3(S-10), Power Cover ---

↓

(3)

Removal

Remove/*Unhook/

Unlock/Release/

Unplug/Desolder

↓

(4)

Note

1

3

---

2

---

↓

(5)

Note:

(1) Identification (location) No. of parts in the figures
(2) Name of the part
(3) Figure Number for reference
(4) Identification of parts to be removed, unhooked,

unlocked, released, unplugged, unclamped, or
desoldered.
P = Spring, L = Locking Tab, S = Screw,
CN = Connector
* = Unhook, Unlock, Release, Unplug, or Desolder
e.g. 2(S-2) = two Screws (S-2),
2(L-2) = two Locking Tabs (L-2)

(5) Refer to “Reference Notes.”

Reference Notes

1. CAUTION 1: Locking Tabs (L-1), (L-2), (L-3) and
(L-4) are fragile. Be careful not to break them.

2. The BD Main CBA & BD Mechanism Assembly
is adjusted as a unit at factory. Therefore, do
not disassemble it. Replace the BD Main CBA
& BD Mechanism Assembly as a unit.

3. When reassembling, be sure to use the original
screws or specified screws listed in the parts
list.

(S-1)

[1] Top Cover

(S-1)

(S-1)

Fig. D1

1-5-1 E5SK6DC

(L-1)

CN1004

(L-2)

CN5000

(L-1)

[7] DC Fan Motor

Fan Cover

Fan Plate

(S-6)

CN1005

*See Reference Notes 3.

[6] *Rear Panel

(S-5)

(S-4)

(S-3)

(S-2)

Fig. D4

[2] Front Unit

[4] Front-B CBA

(L-4)

[5] Front Assembly

(L-3)

Fig. D2

[3] Front-A CBA

Fig. D3

(S-7)

[8] *BD Main CBA
& BD Mechanism
Assembly

CN7101

CN6101

CN7601

(S-8)

* See Reference Notes 2.

Fig. D5

1-5-2 E5SK6DC

Power Cover

(S-10)

(S-10)

[10] Power
Supply CBA

(S-10)

Main PCB Bracket

(S-9)

[9] AV CBA

(S-9)

Desolder

(S-9)

Fig. D6

3. How to Eject Manually

1. Remove the Top Cover, Front Unit and BD Main CBA & BD Mechanism Assembly.

2. Slide the portion A in the direction of the arrow.

3. Pull the tray out manually and remove a disc.

Portion A

1-5-3 E5SK6DC

HOW TO INITIALIZE THE BLU-RAY DISC PLAYER

To put the program back at the factory-default,
initialize the BD player as the following procedure.

Note: By initializing, network is reset to disconnected

state and “Network Service Disclaimer”
appears on the screen.

1. Turn the power on.

2. Remove the disc on the tray and close the tray.

3. Press [1], [2], [3], [4], and [INFO] buttons on the
remote control unit in that order.
Fig. a appears on the screen. All VFD lights.

"

" differ depending on the models.

*******

Version Info

F/W Name
Version
Region
Pickup
ESN
DRM

: *******
: *.***
: *-*
: **
: ***********************************
: OK

EXIT <POWER>EEPROM CLEAR <STOP>

Fig. a

4. Press [ C ] button on the remote control unit.
Fig. b appears on the screen and Fig. c appears
on the VFD.

"

" differ depending on the models.

*******

Version Info

F/W Name
Version
Region
Pickup
ESN
DRM

EEPROM CLEAR : OK

: *******
: *.***
: *-*
: **
: ***********************************
: OK

EXIT <POWER>EEPROM CLEAR <STOP>

Fig. b

Fig. c

5. To exit this mode, press [ ] button.

1-6-1 E5SK0INT

FIRMWARE RENEWAL MODE

Note: The file extension of the available firmware is

“b35”.

1. Turn the power on and remove the disc on the tray
and close the tray.

2. To put the BD player into version up mode, press
[9], [8], [7], [6], and [DISC MENU/POP-UP MENU]
buttons on the remote control unit in that order.
The tray will open automatically.
Fig. a appears on the screen and Fig. b appears
on the VFD.

"

" differ depending on the models.

*******

F/W VERSION UP MODE FW Name:******* Ver *.***

Please Insert a Disc
For F/W Version Up.

Fig. a Version Up Mode Screen

The appearance shown in (*1) of Fig. c is
described as follows:

No. Appearance State

1 Now Loading... Loading the disc

2 Reading...

Sending files into the
memory.

Writing new version data,

3 See FL Display.

the progress will be displayed
as shown in Fig. f.

"

" differ depending on the models.

*******

F/W VERSION UP MODE FW Name:******* Ver *.***

1. ALL
Version : *.*** **************.b35
CHECKSUM : ****

See FL Display.

EXIT : POWER

Fig. e Version Up Mode

Fig. b VFD in Version Up Mode

3. Load the disc for version up.

4. The BD player enters the F/W version up mode
automatically. Fig. c appears on the screen and
Fig. d appears on the VFD. Make sure to insert the
proper F/W for the state of this model.

"

" differ depending on the models.

*******

F/W VERSION UP MODE FW Name:******* Ver *.***

(*1)

Now Loading...

EXIT : POWER

Fig. c Programming Mode Screen (Example)

Fig. d VFD in Programming Mode (Example)

Fig. f VFD in Version Up Mode

5. After programming is finished, the checksum on
the VFD (Fig. g).

Fig. g

VFD upon Finishing the Programming Mode (Example)

Checksum appears on the VFD then the tray will
open automatically. Remove the disc on the tray.

At this time, no button is available.

6. Unplug the AC cord from the AC outlet. Then plug
it again.

7. Turn the power on.

Note: All the settings will be put back to factory-

default.

1-7-1 E5SK0FW

How to Verify the Firmware Version

1. Turn the power on.

2. Remove the disc on the tray and close the tray.

3. Press [1], [2], [3], [4], and [INFO] buttons on the
remote control unit in that order.
Fig. h appears on the screen.

"

" differ depending on the models.

*******

Version Info

F/W Name
Version
Region
Pickup
ESN
DRM

4. To exit this mode, press [ ] button.

: *******
: *.***
: *-*
: **
: ***********************************
: OK

EXIT <POWER>EEPROM CLEAR <STOP>

Fig. h

1-7-2 E5SK0FW

FIRMWARE RENEWAL MODE (for User)

1. Press [ ] button to display Setup menu.

2. Select Settings - Advanced Setup - Others -
Software Upgrade - Disc Upgrade.

3. The screen appears in Fig. a when “Yes” is
chosen and the tray opens. Insert the disc and
press [ A ] button.

Software Upgrade

Please insert a disc for software Upgrade.

If you want to exit Upgrade, press 'BACK'.

Fig. a

4. Disc loading starts. Fig. b will appear on the
screen and Fig. c appears on the VFD.

Software Upgrade

Loading Disc....

6. Firmware loading starts. Fig. f will appear on the
screen and Fig. g appears on the VFD.

Software Upgrade

1.Loading 2.Upgrading

Loading Software...

If you want to exit the download, press 'BACK'.

Fig. f

Fig. g VFD in Update Mode

7. Updating starts automatically. Fig. h will appear
on the screen and update progress will be
displayed as shown in Fig. i on the VFD.

Software Upgrade

1.Loading 2.Upgrading

Upgrading Software...

Fig. b

Fig. c VFD in Update Mode

5. Fig. d will appear on the screen, then select “Yes”.
Fig. e will appears on the VFD.

Software Upgrade

Current Version : X.XXX

: X.XXXInsert Version

Select 'Yes' and press 'OK' button to start upgrading.

Press 'No' to exit software upgrade .

NoYes

Fig. d

Please wait for a few minutes.

Do not unplug the AC cord or interrupt upgrading process.

When upgrade is completed unit will automatically turn Off.

Upgrade disc will eject after unit automatically turns back on.

Fig. h

Fig. i VFD in Update Mode

8. “GOODBYE” on the VFD and power turns off
automatically when it finishes.

9. The power turns on and the tray will open
automatically. Remove the disc on the tray.

Note: The setup setting configured before the update

will be kept.

Fig. e VFD in Update Mode

1-7-3 E5SK0FW

FLOW CHART NO.1

The power cannot be turned on.

TROUBLESHOOTING

Is the fuse normal?

Ye s
Is normal state restored when once unplugged
power cord is plugged again after several seconds?

Ye s
Is 5V voltage outputted to the cathode of D1011?

Ye s

Check each rectifying circuit of the secondary circuit
and service it if defective.

FLOW CHART NO.2

The fuse blows out.

Check the presence that the primary component
is leaking or shorted and service it if defective.

After servicing, replace the fuse.

FLOW CHART NO.3

When the output voltage fluctuates.

Does the photo coupler circuit on the secondary
side operate normally?

Ye s

Check IC1001, IC1003, D1006 and their periphery,
and service it if defective.

No

No

No

No

See FLOW CHART No.2 <The fuse blows out.>

Check if there is any leak or short-circuiting on the
primary circuit component, and service it if defective.
(IC1001,Q1001, Q1002, T1001, D1001, D1002,
D1003, D1004, D1007, C1010, R1013)

Check the presence that the rectifying diode or
circuit is shorted in each rectifying circuit of
secondary side, and service it if defective.

Check IC1003, IC1011 and their periphery,
and service it if defective.

FLOW CHART NO.4

When buzz sound can be heard in the vicinity of power circuit.

Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary
side, and service it if defective. (D1011, D1013, D1014, D1018, D1023, IC2601, IC2602, IC2640, IC2660,
Q1011,Q2603, Q2604, Q2606)

FLOW CHART NO.5

-FL is not outputted.

Is -30V voltage supplied to the anode of D1018?

Ye s
Check for load circuit short-circuiting or leak, and
service it if defective.

No

Check D1009, D1018, C1021 and periphery circuit,
and service it if defective.

1-8-1 E5SK6TR

FLOW CHART NO.6

P-ON+13V-A(-B) is not outputted.

Is 13V voltage supplied to the emitter of Q2603?

Ye s

Is 12V voltage supplied to the base of Q2603?

Ye s

Replace Q2603.

FLOW CHART NO.7

P-ON+5V (P-ON+5V(2)) is not outputted.

Is 5V voltage supplied to the emitter of Q2604?

Ye s

Is 4.3V voltage supplied to the base of Q2604?

Ye s

Replace Q2604.

FLOW CHART NO.8

P-ON+5V (1) is not outputted.

Is 5V voltage inputted to the emitter of Q2606?

Ye s

No

No

No

No

No

Check D1023, C1018, C1024, C1026, L1003 and
their periphery circuit, and service it if defective.

Check Q2601 and PWSW4 line and service it if
defective.

Check D1011, D1013, D1014, C1019, C1025, and
their periphery circuit, and service it if defective.

Check Q2605 and PWSW4 line and service it if
defective.

Check D1011, D1013, D1014, C1019, C1025, and
their periphery, and service it if defective.

Is 4.4V voltage supplied to the base of Q2606?

Ye s

Replace Q2606.

FLOW CHART NO.9

P-ON+10.5V is not outputted.

Is 13V voltage inputted to Pin(2) of IC2640?

Ye s

Is the "H" signal inputted to Pin(7) of IC2640? Replace IC2000.

Ye s

Replace IC2640.

FLOW CHART NO.10

P-ON+1.2V is not outputted.

Is 5V voltage supplied to Pin(3) of IC2601?

Ye s

Is the "H" signal inputted to Pin(7) of IC2601? Replace IC2000.

Ye s

Replace IC2601.

No

No

No

No

No

Check Q2605 and PWSW4 line and service it if
defective.

Check D1023, C1018, C1024, C1026, L1003
their periphery, and service it if defective.

Check D1011, D1013, D1014, C1019, C1025
the periphery circuit, and service it if defective.

and

and

1-8-2 E5SK6TR

FLOW CHART NO.11

P-ON+1.8V is not outputted.

Is 5V voltage supplied to Pin(3) of IC2602?

Ye s

Is the "H" signal inputted to Pin(7) of IC2602?

Ye s

Replace IC2602.

FLOW CHART NO.12

EV+3.9V is not outputted.

Is 5V voltage supplied to the

Is 4.5V voltage supplied to the

Replace Q1011.

FLOW CHART NO.13

P-ON+3.3V is not outputted.

Is 5V voltage supplied to Pin(3) of IC2660?

Is the "H" signal inputted to Pin(7) of IC2660? Replace IC2000.

Replace IC2600.

collector

Ye s

Ye s

Ye s

Ye s

base

of Q1011?

of Q1011?

No

No

No

No

No

No

Check D1011, D1013, D1014, C1019, C1025 and their
periphery circuit, and service it if defective.

Replace IC2000.

Check D1011, D1013, D1014, C1019, C1025, and
their periphery circuit, and service it if defective.

Check IC1012, R1046, R1048, and their periphery
circuit, and service it if defective.

Check D1011, D1013, D1014, C1019, C1025 and
their periphery circuit, and service it if defective.

FLOW CHART NO.14

The fluorescent display tube does not light up.

Is 5V voltage supplied to Pin(13, 43) of IC5001?

Ye s
Is approximately -24V to -28V voltage supplied to
Pin(30) of IC5001?

Ye s
Is there approximately 500kHz oscillation to
Pin(5) of IC5001?

Ye s
Are the filament voltage applied between Pin(1, 2)

and Pin(31, 32) of the fluorescent display tube?
Also negative voltage applied between these pins
and GND?

Ye s
Check the fluorescent display tube (FL5001),
and

service it if defective.

No

No

No

No

Check the P-ON+5V line and service it if defective.

Check the -FL line and service it if defective.

Check R5007, IC5001 and their periphery, and
service it if defective.

Check the power circuit, D1010, D1017, C1016,
C1038 and their periphery, and service it
if defective.

1-8-3 E5SK6TR

FLOW CHART NO.15

The key operation is not functioning.

Are the contact point and the installation state
of the key switches (SW3007-SW3011) normal?

Ye s

When pressing each switches (SW3007-SW3011),
do the voltage of Pin(1) of IC2000 increase?

Ye s

Replace IC2000.

FLOW CHART NO.16

No operation is possible from the remote control unit.(Operation is possible from the unit.)

Is 3.3V voltage supplied to Pin(2) of RS5000
(remote control receiver) ?

Ye s
Is the "L" pulse sent out Pin(1) of RS5000 (remote
control receiver) when the remote control unit is activated?

Ye s

Is the "L" pulse inputted to the Pin(27) of IC2000?

Ye s

Replace IC2000.

No

No

No

No

No

Re-install the switches (SW3007-SW3011)
correctly or replace the poor switch.

Check the switches (SW3007-SW3011) and their
periphery, and service it if detective.

Check EV+3.3V line and service it if defective.

Replace the RS5000 (remote control receiver) or
remote control unit.

Check the line between the
receiver)
detective.

and the

Pin(27) of IC2000,

RS5000 (remote control

and service it if

FLOW CHART NO.17

The disc tray cannot be opened and closed. (It can be done using the remote control unit.)

Is the normal control voltage inputted to Pin(1) of
IC2000? Refer to "FLOW CHART NO.15" <The key
operation is not functioning.>

Ye s

Replace the BD Main CBA & BD Mechanism
Assembly.

No

Replace the "OPEN/CLOSE" switch (SW3011).

1-8-4 E5SK6TR

FLOW CHART NO.18

The disc tray cannot be opened and closed.
[No Disc] indicated.
Both functions of picture and sound do not operate normally.

Ye s

Replace the BD Main CBA & BD Mechanism
Assembly.

FLOW CHART NO.19

Picture does not appear normally.

Set the disc on the disc tray, and playback.

Are the video signals outputted to each pin of
CN2200?

CN2200 13PIN VIDEO
CN2200 11PIN VIDEO-Y(I/P)
CN2200 9PIN VIDEO-Pb/Cb
CN2200 7PIN VIDEO-Pr/Cr

Ye s

Are the video signals shown above inputted into
each pin of IC2300?

IC2300 1PIN VIDEO
IC2300 3PIN VIDEO-Y(I/P)
IC2300 4PIN VIDEO-Pb/Cb
IC2300 5PIN VIDEO-Pr/Cr

Ye s

Are the video signals outputted to each pin of
IC2300?

IC2300 14PIN VIDEO
IC2300 12PIN VIDEO-Y(I/P)
IC2300 10PIN VIDEO-Pb/Cb
IC2300 9PIN VIDEO-Pr/Cr

Ye s

Are the video signals outputted to the specific
output terminal?

Are the component video signals outputted to the
VIDEO OUT terminal (JK2300)?

Are the composite video signals outputted to
the VIDEO OUT terminal (JK2300)?

No

No

No

No

No

Replace the BD
Assembly.

Check the line between each pin of CN2200 and
each pin of IC2300, and service it if detective.

CN2200 13PIN → IC2300 1PIN VIDEO
CN2200 11PIN → IC2300 3PIN VIDEO-Y(I/P)
CN2200 9PIN → IC2300 4PIN VIDEO-Pb/Cb
CN2200 7PIN → IC2300 5PIN VIDEO-Pr/Cr

Is 5V voltage supplied to the Pin(13) of IC2300?

Ye s

Replace IC2300.

Check the periphery of JK2300 from Pin(9, 10, 12)
of IC2300 and service it if detective.

Check

the periphery of

IC2300

and service it if detective.

Main CBA & BD Mechanism

No
Check P-ON+5V line and
service it if detective.

JK2300 from Pin(14) of

1-8-5 E5SK6TR

FLOW CHART NO.20

Audio is not outputted normally.

Set the disc on the disc tray, and playback.

Are the analog audio signals outputted to each pin
of CN2200?

CN2200 16PIN AUDIO(L)
CN2200 18PIN AUDIO(R)

Ye s

Are the analog audio signals inputted to each pin
of IC2200?

IC2200 6PIN AUDIO(L)
IC2200 2PIN AUDIO(R)

Ye s

Is the "H" level mute signal outputted to CN2200?

CN2200 20PIN AUDIO(R)-MUTE
CN2200 19PIN AUDIO(L)-MUTE

Ye s

Is the signal at Pin(24) of IC2000 "H" ?

Ye s

Are the analog audio signals outputted to each pin
of IC2200?

IC2200 7PIN AUDIO(L)
IC2200 1PIN AUDIO(R)

Ye s

Are the audio signals outputted to the audio
terminal (JK2300)?

No

No

No

No

No

No

Replace the BD
Assembly.

Check each line between each pin of CN2200
and each pin of IC2200, and service it if detective.

CN2200 16PIN → IC2200 6PIN AUDIO(L)
CN2200 18PIN → IC2200 2PIN AUDIO(R)

Replace the BD
Assembly.

Check

AUDIO-MUTE line, and

detective.

Replace IC2200.

Check the periphery between Pin(1,7) of IC2200
and JK2300, and service it if detective.

Main CBA & BD Mechanism

Main CBA & BD Mechanism

service it if

1-8-6 E5SK6TR

INTERNET RADIO (vTuner) ERROR CODE

Error Code appears in the error screen when the unit
detects an error, as shown below. The code is used to
specifically determine the cause of error.

Network Error

Network Error

Play bac k Error.

Connection Error

OK

OKOK

NE[00103203]

NE[00103404]

Error CodeError message

Fig. 1: Error Code (Example)

Error Code are displayed with “NE[********]” (“*” is
error code) as shown above.

Error Code Form

In the Internet Radio(vTuner), Error Code are used as
follows.

001XXXXX

Detailed Error Code
Summary Error Code

Fig. 2

“Summary Error Code” are shown in the list below.

Summary

Error Code

01

Cannot connect to server. Please
check your settings.

Error message

02 Playback Error
03 Connection Error

• The Detailed Error Code shows the three-digit code
used in the HTTP Status Code or used internally in
the Application.

• The HTTP Status Codes (200 to 500 series) are
defined in the RFC2616.

• Depending on the specification of the station or the
server, error codes not listed in the table may
appear.

1-9-1 E5P50ER

Detailed Error Code table (vTuner – HTTP Status Code)

Status Code Description

201 Created A new resource was created by this unit’s request.

202 Accepted This unit’s request was accepted but its processing is not completed.

204 No Content Though the server processed the request, there was no content.

304 Not Modified

400 Bad Request The server cannot understand this unit’s request.

401 Unauthorized The resource this unit has requested needs to be authorized.

403 Forbidden

404 Not Found The URI this unit has requested is not found.

500 Internal Server Error Internal server error occurred.

501 Not Implemented

502 Bad Gateway

503 Service Unavailable Because of overloading or maintenance, the server is temporarily unavailable.

This unit caches latest resource and the requested resource is not modified.
(exception protocol error)

The server has received the requests from this unit but refused to process
them.

The server does not support functionalities required to process the request
from this unit.

The proxy server between this unit and the server received an invalid reply
from another proxy or the original server.

Detailed Error Code table (vTuner – Application Status Code)

Status Code Description

001 Nothing List

002 LAN Disconnect This unit’s LAN is disconnected.

005 Favorite Error The URL needed to register or delete favorite data is not sent from the server.

601 Stream Stop

602 Unsupported(Info) The stream information of the broadcast is unsupported.

603 Decode Timeout

604 Unsupported(Stream) As a result of analyzing the received stream data, the data is unsupported.

605 Decode Failed The received stream data cannot be decoded.

606 Multi Stream

As a result of list creation process, there is no item to be displayed from the
received data.

Because the streaming stopped, decoding has stopped. (This error message
is displayed if decoding is disabled for 20 seconds.)

The unit tried to playback the received stream data, but the data was not
played correctly even after three minutes elapsed.

Because this unit received multiple streaming data, the data cannot be
decoded.

1-9-2 E5P50ER

Status Code Description

701 Protocol Error

702 Start Up Error The application of this unit failed to start.

703 URL Error The URL which this unit specified is in invalid form.

705 Connect Failed

706 Connect Failed Connection with the server or the broadcast has failed. (IP conversion error)

707 Connect Failed Connection with the server or the broadcast has failed.

723 Analyze Error The received protocol data cannot be analyzed.

727 System Error(Memory)

728 Response Timeout A response timeout occurred to unit’s connection request.

743 System Error(Program)

745 System Error(LAN Port)

An exception error occurred during communication between the server or the
broadcast.

Connection with the proxy which exists between this unit and the server or the
broadcast has failed. (IP conversion error)

A system error occurred in the unit. (memory shortage, internal cURL pro­cessing error)

A system error occurred in the unit. (program error, internal cURL processing
error)

A system error occurred in the unit. (LAN unusable, internal cURL processing
error)

752 Response Timeout A response timeout occurred to unit’s connection request.

755 Disconnect Error(Send)

Disconnect

756

Error(Receive)

761 Analyze Error The received protocol data cannot be analyzed.

790 List Not Found The list information which was sent from the server is invalid or not found.

791 Stream Timeout The stream data is not sent from the broadcast.

* Server: vTuner broadcast list server
* Broadcast: Server of internet radio broadcast

Because the connection between this unit and the server or the broadcast was
disconnected, it has failed to send the protocol data.

Because the connection between this unit and the server or the broadcast was
disconnected, it has failed to receive the protocol data.

1-9-3 E5P50ER

BLOCK DIAGRAMS

System Control Block Diagram

EV+3.9V

TO VIDEO

BLOCK DIAGRAM

SD/HD

PWSW1

VIDEO-MUTE

PWSW2

PWSW3

TO POWER SUPPLY

BLOCK DIAGRAM

PWSW4

FAN-CONT

FL-SW

TO AUDIO

BLOCK DIAGRAM

AUDIO-MUTE

EV+3.3V

REMOTE

RS5000

IC5001 (VFD DRIVER)

SENSOR

FL5001

GRID VFD

~

~

14

35

42

~

~

P1

1G

8G

VFD-CLK

VFD-DIN

VFD-STB
987

VFD-STB

66VFD-DAT48

55VFD-CLK

11REMOTE

44

CN2002 CN5000

BUFFER

Q2008

SEGMENT

31

29

32

P17

P16

P18

KEY SWITCH

STANDBY

D3009

FRONT-B CBA

FRONT-A CBA

STANDBY-LED

AD-KEY1

22

11

POWER

SUPPLY CBA

AD-KEY1

STANDBY-LED

66

77

CN2101 CN1003 CN1004 CN3004

40

20VIDEO-MUTE

30SD/HD

(SUB MICRO CONTROLLER)

IC2000

1 NOTE:

Either IC2001 or IC2002 is used for AV CBA.

PWSW137PWSW238PWSW3

OSC2

OSC1
9

8

6MHz

X'TAL

X2000

39

25FAN-CONT

PWSW4

45

FL-SW

*1

24

AUDIO-MUTE

SWITCHING

Q2620, Q2621

JK7501

IC2001

CEC-OUT

31 CEC-IN

32

BUFFER

Q2619

CN2200

20 5CEC

CN7101

13

CEC

RESET

14

RESET

IC2002

RESET

27

REMOTE

Q2010

BUFFER

BUFFER

47

50

VFD-DAT

VFD-STB

VFD-CLK

Q2009

IC6001

(MAIN MICRO CONTROLLER)

SUB-TXD
18

23 2SUB-TXD

CN7101 CN2200

V32

TXD1

SUB-RXD

SYS-RESET

19

23

21 4SYS-RESET

24 1SUB-RXD

U34

RXD1

T34

XRST

A27

AE32

XTRST

XFERST

1AD-KEY1

Q6702

Q2007

26

STANDBY-LED

IC6701

P-ON+1.8V

Q6701

RESET

2 1

BD MAIN CBA AV CBA

1-10-1

E5SK6BLS

Digital Signal Process 1 Block Diagram

VIDEO SIGNAL AUDIO SIGNAL

(MAIN MICRO CONTROLLER/DIGITAL SIGNAL PROCESS)

IC6001

MPX

MATRIX

B31,C31

A32,B32,

/LPP

WOB

B30,C30

A30,A31,

TO DIGITAL SIGNAL

PROCESS 2 BLOCK

DIAGRAM

(IC6001)

STREAM

CONTROL

FE

DIGITAL

SIGNAL

PROCESS

RF

EQUALIZER

RF

GENERATOR

B34

C33

G30

G31

SDATA2

M31

SCLK2

M32

TRACKING-CONTROL

E23

27

TRACKING

ACTUATOR

IC302 (MOTOR DRIVE)

262524

DRIVE

COPY

FOCUS1-CONTROL

A24

FOCUS 1

ACTUATOR

DRIVE

23

AACS

PROTECT

FOCUS2-CONTROL

D23

29

FOCUS 2

ACTUATOR

22

BD+

DRIVE

21

CSS

CPRM

EXPA-CONTROL

B22

162815

COLLIMATE

LENS

201918

EXPB-CONTROL

D22

MOTOR DRIVE

17

40

SLED1-CONTROL

SLED2-CONTROL

D24

C24

37

38

SLED

MOTOR DRIVE

2

41

TRAY-OUT

TRAY-IN

LOAD-CONTROL

C22

D21

LOADING

MOTOR DRIVE

1

4

5

SPINDLE-CONTROL

E217E24

10

IC301 (MOTOR DRIVE)

242119131415161718

SPINDLE

MOTOR

DRIVE

SPINDLE-FG

B25

4

12

Q101

*1: 14, 16, 18, 26

*2: 13, 15, 27, 29

CN101

A-D *1

E-H *2

Q102

BUFFER

BUFFER

RF(-) 21

RF(+) 20

BDRF(+) 23

OEIC

(CD/DVD)

CN101

TD 3

TR 4

FR1 5

FD1 6

FD2 2

LASER

DIODE

FR2 1

DRIVE

EXPA(-) 10

EXPB(-) 8

EXPA(+) 9

EXPB(+) 7

SCLK2 39

SDATA2 38

BDRF(-) 24

OEIC

(BD)

CN301

SLD2(+) 4

SLD2(-) 3

SLED

CN302

SLD1(-) 1

LOAD(+) 16

LOADING

MOTOR

LOAD(-) 17

SLD1(+) 2

MOTOR

1-10-2

TRAY-OUT 14

TRAY-IN 13

TRAY-OUT

CN302

V3

U4

W2

TRAY-IN

HU(-) 7

HU(+) 6

SPINDLE

HV(-) 9

HV(+) 8

MOTOR

VH(-) 12

HW(-) 11

HW(+) 10

BD MECHANISM BD MAIN CBA

E5SK6BLD1

Digital Signal Process 2 Block Diagram

TO VIDEO

BLOCK DIAGRAM

SCL3

PRMY(0-11)

SDA3

27MHz

OSC

X6701

231

16

SCL

SDA

CLOCK

GENERATOR

IC6702 (CLOCK GENERATOR)

789

10

VIDEO SIGNAL AUDIO SIGNAL

VIDEO

VIDEO-Pr/Cr

VIDEO-Y(I/P)

VIDEO-Pb/Cb

PRMVS

PRMCLK

PRMHS

PRMC(0-11)

TO AUDIO

MC

MD

DAC-SCK

DAC-BCK

BLOCK DIAGRAM

MS1

DAC-LRCK

DATA

SPDIF

TO VIDEO

BLOCK DIAGRAM

HDMI-BCK

HDMI-MCK

HDMI-DATA0

HDMI-DATA1

HDMI-DATA2

HDMI-LRCK

HDMI-DATA3

HDMI-SPDIF

IC6001 (MAIN MICRO CONTROLLER/DIGITAL SIGNAL PROCESS)

CN6101

CN2001

AV CBA BD MAIN CBA

CN4000

SD DATA(0-3)

23 23SDDAT0

C15

D18

VIDEO

SD I/F

AF32,AG34,

AH33,AJ34

21 21SDDAT1

26 26SDDAT2

A2

B6

B5

A4,A8,A9,B4,B9,C5,C9,

C11,D8,D10,E10,E11

A3,A6,A7,B7,C4,C6,C7,

USBDP

USBDN

AA34

AA33

33USBDP

22USBDN

C8,D6,D9,E8,E12

DIGITAL

VIDEO

OUT

FROM DIGITAL

SIGNAL PROCESS 1

R33

SCL3

BLOCK DIAGRAM

(IC6001)

U31

SDA3

AL34

AL5

E20

A19

33M CLOCK

33M CLOCK

74M CLOCK

27M CLOCK

I/P CONVERTER

/SCALING

Java (BD-J)

MPEG-2

DiVX

VC-1

H.264

MII-RXD (0-3), MII-TXD (0-3)

ETHERNET

INTERFACE

IC6401

JK6401

TX(-) 2

RX(-) 6

TX(+) 1

RX(+) 3

(ETHERNET JACK)

D20

768K CLOCK

DECODER

HD (TS)

E13

SD (PS)

(NAND FLASH MEMORY)

IC6901

B10

B11

A10

A11

ED (0-7)

NAND FLASH

MEMORY (256M x 8bit)

D11

C12

C10

DIGITAL

IC6501,IC6502

B14

A12

C14

D12

AUDIO

OUT

MEMORY

I/F

C0A (0-12)

C0DQ (0-31)

DDR2 SDRAM

(1Gbit )

(DDR2 SDRAM)

B13

A13

B12

AC31

C1A (0-12)

C1DQ (0-31)

DDR2 SDRAM

(512Mbit)

(DDR2 SDRAM)

IC6601,IC6602

F17

B17

CLK

VSYNC

HSYNC

DAC

MEDIA

PROCESSOR

SDCLK

AH34

CN7601

28 28SDDAT3

29 29SDCLK

CN2301

CN2300

SD

CARD

SLOT

USB

JACK

1-10-3

E5SK6BLD2

Video Block Diagram

VIDEO SIGNAL AUDIO SIGNAL

AV CBABD MAIN CBA

JK2300

WF3

75Ω

2dB

LPF 14

4dB

IC2300 (VIDEO DRIVER)

1

VIDEO OUT

C2303

DRIVER

75Ω

AMP

2dB

6.75MHz

AMP

4dB

VIDEO-Y

OUT

DRIVER

AMP

LPF

13.5/37MHz

AMP

3 12

VIDEO-Pb/Cb

OUT

10

75Ω

DRIVER

2dB

AMP

LPF

13.5/37MHz

4dB

AMP

4

VIDEO-Pr/Cr

OUT

9

75Ω

DRIVER

2dB

AMP

LPF

13.5/37MHz

4dB

AMP

5

MUTE

SD/HD

6

8

VIDEO-MUTE

SD/HD

MUTE

7

JK7501

HDMI-CONNECTOR

96

DDC

AUTHENT

/CATION

KEY

EXCHANGE

REGISTER

IIC

I/F

IC7501 (HDMI INTERFACE)

CLK

1

27

29

DDC DATA

DDC CLOCK

HOT PLUG

DETECT

191516

98

97

I/F

VS

HS

31

32

T.M.D.S DATA2-

T.M.D.S DATA2+

T.M.D.S DATA1-

T.M.D.S DATA1+

T.M.D.S DATA0-

31649

22241820141612

TMDS
SERIALIZER

TMDS
ENCODER

HDCP
CIPHER/
ENCRYPTOR

AV
CONTROLLER

VIDEO

I/F

T.M.D.S DATA0+

7

AUDIO
I/F

86848583918889

T.M.D.S CLOCK+

T.M.D.S CLOCK-

10

12

10

81

CN2200CN7101

12 13VIDEO

VIDEO

VIDEO-Y(I/P)

14 11VIDEO-Y(I/P)

16 9VIDEO-Pb/Cb

18 7VIDEO-Pr/Cr

VIDEO-Pb/Cb

VIDEO-Pr/Cr

WF1 WF2

TO SYSTEM CONTROL

BLOCK DIAGRAM

TO DIGITAL

SIGNAL

PROCESS 2

BLOCK DIAGRAM

SCL3

SDA3

PRMCLK

PRMVS

PRMHS

51-56,58,59,

35-37,39-41,

43,44,66-68,70

PRMC(0-11)

PRMY(0-11)

71,72,74,75

HDMI-DATA0

HDMI-DATA1

HDMI-DATA2

HDMI-DATA3

HDMI-MCK

HDMI-BCK

HDMI-LRCK

HDMI-SPDIF

TO DIGITAL

SIGNAL

PROCESS 2

BLOCK DIAGRAM

1-10-4

E5SK6BLV

Audio Block Diagram

AUDIO SIGNAL

JK2300

7

AUDIO(L)-

OUT

MUTE-ON

Q2203

DRIVE

Q2200

AUDIO(R)-

Q2202

Q2201

1

OUT

MUTE-ON

DRIVE

JK2100

Q2100

DIGITAL

AUDIO OUT

BUFFER

(COAXIAL)

AV CBABD MAIN CBA

IC2200

(OP AMP)

WF4

6

916AUDIO(L)

CN7101 CN2200

15

(L-CH)

(R-CH)

2

718AUDIO(R)

124SPDIF

619AUDIO(L)-MUTE

520AUDIO(R)-MUTE

14

L-CH

MUTE

AUDIO-MUTE

TO SYSTEM CONTROL

WF5

1

16

R-CH

MUTE

BLOCK DIAGRAM

IC7001(AUDIO D/A CONVERTER)

3458276

MCMDDAC-SCK

1-10-5

AUDIO

DAC

DAC-BCK

DAC-LRCK

MS1

TO DIGITAL

DATA

SIGNAL

PROCESS 2

SPDIF

BLOCK DIAGRAM

E5SK6BLA

Power Supply Block Diagram

TO BD

MAIN CBA

(CN6101)

P-ON+1.2V

4 P-ON+5V(1)

10,12 P-ON+10.5V

19,20 P-ON+3.3V

CN2001

NOTE:

The voltage for parts in hot circuit is measured using

hot GND as a common terminal.

22 P-ON+5V(2)

1-3 P-ON+1.8V

9,11,13

Q2002,Q2003

6 P-ON+5V

Q2004

FAN

CONTROL

Q2006

-FLF1F2

EV+3.3V

P-ON+13V-A

Q2603

P-ON+13V-B

P-ON+5V

SW+13V

IC2640

P-ON+3.3V

+10.5V REG.

Q2601

Q2606

SW+5V

Q2608, Q2609

Q2604

LIMIT

CURRENT

SW+5V

FLSW

FAN-CONT

TO SYSTEM

CONTROL

BLOCK

DIAGRAM

PWSW4

PWSW1

PWSW2

IC2660

Q2605

PWSW3

REG.

+3.3V

IC2602

+1.8V

IC2601

REG.

+1.2V

AV CBAPOWER SUPPLY CBA

REG.

FAN

"Ce symbole reprèsente un fusible à fusion rapide."

"This symbol means fast operating fuse."

CAUTION !

For continued protection against fire hazard,

replace only with the same type fuse.

ATTENTION : Pour une protection continue les risqes

d'Incele n'utiliser que des fusible de même type.

Risk of fire-replace fuse as marked.

F

FAN11GND

CN1005

2

A V

T1001

D1001 - D1004

L1001

F

F1001

2.5A 250V

A V

HOT CIRCUIT. BE CAREFUL.

CN2100CN1002

12

1

BRIDGE

RECTIFIER

LINE

FILTER

1

FAN 1
1

CN1003 CN2101

F1002

11

3

Q1001

5

)

SWITCHING

2

CONTROL

1

SWITCHING CONTROL

IC1001

(

3

8

10

F2

F1

EV+3.9V

-FL

8

3

9 9

10

IC1012,

10

6

VDD

3

Q1011

REG.

+3.9V

9

Q1002

6

CN2100

AL+13V
6

CN1002

789

EV+5V

AL+13V

8

7

8

10

EV+5V

EV+5V

9

10

6

11

EV+5V
11

COLD

REG.

7

5

IC1003

ERROR

VOLTAGE DET

1

4

SHUNT

2

3

IC1011

ERROR

VOLTAGE DET

HOT

CAUTION !

Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.

If Main Fuse (F1001) is blown , check to see that all components in the power supply

circuit are not defective before you connect the AC plug to the AC power supply.

Otherwise it may cause some components in the power supply circuit to fail.

AC1001

AC CORD

1-10-6

E5SK6BLP

SCHEMATIC DIAGRAMS / CBA AND TEST POINTS

Standard Notes

WARNING

Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using
replacement components rated for higher voltage,
wattage, etc. Replacement parts that have these
special safety characteristics are identified in this
manual and its supplements; electrical components
having such features are identified by the mark “#” in
the schematic diagram and the parts list. Before
replacing any of these components, read the parts list
in this manual carefully. The use of substitute
replacement parts that do not have the same safety
characteristics as specified in the parts list may create
shock, fire, or other hazards.

Notes:

1. Do not use the part number shown on these
drawings for ordering. The correct part number is
shown in the parts list, and may be slightly
different or amended since these drawings were
prepared.

2. All resistance values are indicated in ohms
(K = 10

3. Resistor wattages are 1/4W or 1/6W unless
otherwise specified.

4. All capacitance values are indicated in µF
(P = 10

5. All voltages are DC voltages unless otherwise
specified.

6. Electrical parts such as capacitors, connectors,
diodes, IC’s, transistors, resistors, switches, and
fuses are identified by four digits. The first two
digits are not shown for each component. In each
block of the diagram, there is a note such as
shown below to indicate these abbreviated two
digits.

3

, M = 106).

-6

µF).

1-11-1 BDN_SC

LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON

r

THE FOLLOWING PAGES:

1. CAUTION:

FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE

F

A V

SAME TYPE FUSE.
ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER
QUE DES FUSIBLE DE MÊME TYPE.
RISK OF FIRE-REPLACE FUSE AS MARKED.

This symbol means fast operating fuse.
Ce symbole represente un fusible a fusion rapide.

2. CAUTION:

Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown, first check to see that all components in the power supply circuit are not
defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components
in the power supply circuit to fail.

3. Note:

1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.

2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.

4. Voltage indications for PLAY and STOP mode on the schematics are as shown below:

2

1

(Unit: Volt)

The same voltage for
both PLAY & STOP modes

5.0

3

5.0
(2.5)

Indicates that the voltage
is not consistent here.

PLAY mode
STOP mode

5. How to read converged lines

1-D3

Distinction Area

Line Number
(1 to 3 digits)

Examples:

1. "1-D3" means that line number "1" goes to the line numbe
"1" of the area "D3".

2. "1-B1" means that line number "1" goes to the line number
"1" of the area "B1".

3

AREA D3

2

1

ABCD

AREA B1

1-D3

1-B1

6. Test Point Information

: Indicates a test point with a jumper wire across a hole in the PCB.

: Used to indicate a test point with a component lead on foil side.

: Used to indicate a test point with no test pin.

: Used to indicate a test point with a test pin.

1-11-2 BDN_SC

Power Supply Schematic Diagram

CAUTION !

Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.

F

A V

CAUTION !

For continued protection against fire hazard,
replace only with the same type fuse.
ATTENTION : Pour une protection continue les risqes
d'Incele n'utiliser que des fusible de même type.
Risk of fire-replace fuse as marked.

"This symbol means fast operating fuse."
"Ce symbole reprèsente un fusible à fusion rapide."

NOTE:

The voltage for parts in hot circuit is measured using
hot GND as a common terminal.

1-11-3

E5SK6SCP

AV 1 Schematic Diagram

1-11-4

E5SK6SCAV1

AV 2 Schematic Diagram

1 NOTE:
Either IC2001 or IC2002 is used for AV CBA.

1-11-5

E5SK6SCAV2

AV 3 Schematic Diagram

1-11-6

E5SK6SCAV3

Front-A Schematic Diagram

1G 2G 3G 4G 5G 6G 7G 8G
P1
P2
P3
P4
P5
P6
P7
P8
P9

P10
P11
P12
P13
P14
P15
P16
P17
P18

FL5001 MATRIX CHART

S7

S8

S2

S4

S3hhhhhhh

S5

S6

S1

S9

f

j

a

f

j

a

f

j

a

f

j

a

fff

jjj

S10

S11
S12
S13

g
s

k
b

m

e

r
p
n
c
d

g
s

k
b

m

e

r
p
n
c
d

g
s

k
b

m
e

r
p
n
c
d

g
s

k
b

m

e

r
p
n
c
d

g

s

k

b

m
e

r
p
n

c
d

g
s

k
b

m

e

r
p
n
c
d

g
s

k
b

m

e

r
p
n
c
d

aaa

1G 2G 3G 4G 5G 6G 7G 8G

S7 S11

S4 S8

S1
S5

S2

S12

S3

S6S9S10

S13

j

a

h

k

b

f

g

m

s

c

e

n

r

p

d

1-11-7

E5SK6SCFA

Front-B Schematic Diagram

1-11-8

E5SK6SCFB

BD Main 1 Schematic Diagram

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1-11-9

E5SK6SCBD1

BD Main 2 Schematic Diagram

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1-11-10

E5SK6SCBD2

BD Main 3 Schematic Diagram

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1-11-11

E5SK6SCBD3

BD Main 4 Schematic Diagram

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1-11-12

E5SK6SCBD4

BD Main 5 Schematic Diagram

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1-11-13

E5SK6SCBD5

BD Main 6 Schematic Diagram

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1-11-14

E5SK6SCBD6

BD Main 7 Schematic Diagram

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1-11-15

E5SK6SCBD7

BD Main 8 Schematic Diagram

1-11-16

E5SK6SCBD8

BD Main 9 Schematic Diagram

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1-11-17

E5SK6SCBD9

BD Main 10 Schematic Diagram

1-11-18

E5SK6SCBD10

BD Main 11 Schematic Diagram

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1-11-19

E5SK6SCBD11

Because a hot chassis ground is present in the power supply
circuit, an isolation transformer must be used when repairing.
Also, in order to have the ability to increase the input slowly,
when troubleshooting this type of power supply circuit,
a variable isolation transformer is required.

CAUTION !

Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.

"Ce symbole reprèsente un fusible à fusion rapide."

CAUTION !

For continued protection against fire hazard,
replace only with the same type fuse.
ATTENTION : Pour une protection continue les risqes
d'Incele n'utiliser que des fusible de même type.
Risk of fire-replace fuse as marked.

"This symbol means fast operating fuse."

A V

F

Power Supply CBA, AV CBA, Front-A CBA & Front-B CBA Top View

Power Supply

CBA

AV CBA

Not used

NOTE:

The voltage for parts in hot circuit is measured using
hot GND as a common terminal.

Front-A CBA

Not used

1-11-20

Front-B CBA

BE5SK0F01011

Because a hot chassis ground is present in the power supply
circuit, an isolation transformer must be used when repairing.
Also, in order to have the ability to increase the input slowly,
when troubleshooting this type of power supply circuit,
a variable isolation transformer is required.

CAUTION !

Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.

"Ce symbole reprèsente un fusible à fusion rapide."

CAUTION !

For continued protection against fire hazard,
replace only with the same type fuse.
ATTENTION : Pour une protection continue les risqes
d'Incele n'utiliser que des fusible de même type.
Risk of fire-replace fuse as marked.

"This symbol means fast operating fuse."

A V

F

Power Supply CBA, AV CBA, Front-A CBA & Front-B CBA Bottom View

AV CBA

Not used

WF3

C2303
PLUS LEAD

WF1

WF1

PIN 7 OF
CN2200

WF1

WF2 WF1

PIN 9 OF
CN2200

WF4

PIN 16 OF
CN2200

WF1

WF5

PIN 24 OF
CN2200

Power Supply

CBA

NOTE:

The voltage for parts in hot circuit is measured using
hot GND as a common terminal.

Front-B CBA

1-11-21

Front-A CBA

Not used

BE5SK0F01011

WF1

Pin 7 of CN2200

WAVEFORMS

WF4

Pin 16 of CN2200

VIDEO-Pr/Cr 0.2V 10

WF2

Pin 9 of CN2200

VIDEO-Pb/Cb 0.2V 10

WF3

C2303 PLUS LEAD

µ

s

µ

s

AUDIO(L) 1V 0.5ms

WF5

Pin 24 of CN2200

SPDIF 1V 0.1

µ

s

20µs0.5VVIDEO-CVBS

NOTE:

Input Signal (DVD)
VIDEO: 75% COLOR BAR
AUDIO: 1KHz, 0dB

1-12-1 B3NWF

FAN

AC

CORD

FAN1

GND

1
2

CN1004 CN3004

12345

STANDBY-LED

GND

AD-KEY1
12345

CN1005

POWER SUPPLY CBA FRONT-B CBA

FRONT-A CBA

EV+3.9V

NU

CN1002

CN1003

CN5000

WIRING DIAGRAM

USB
JACK

SD CARD
SLOT

DIGITAL
AUDIO
OUT
(COAXIAL)

AUDIO(R)

-OUT

AUDIO(L)

-OUT

VIDEO­Pr/Cr
OUT

VIDEO­Pb/Cb
OUT

VIDEO-Y
OUT

VIDEO

-OUT

6

NU
6

FAN 1

1

GND

2

GND

3

GND

4

GND

5

AL+13V

6

AL+13V

7

EV+5V

8

EV+5V

9

EV+5V

10

EV+5V

11

GND

1

GND

2

EV+3.9V

3

NU

4

NU

5

AD-KEY1

6

STANDBY-LED

7

F2

8

-FL

9

F1

10

GND

11

REMOTE

1

EV+3.3V

2

P-ON+5V

3

VFD-STB

4

VFD-CLK

5

VFD-DAT

6

GND

7

F1

8

F2

9

-FL

10

AV CBA

W1

1
2
3
4
5
6
7

CN2100CN2101

8

9
10
11

W2

1

2

3

4

5

6

7

8

9
10
11

1

2

3

4

5

6

CN2002

7

8

9
10

BUS-POWER

1

USBDN

2

USBDP

3

GND

4

CN2301

GND

5

P-ON+1.8V

1

P-ON+1.8V

2

P-ON+1.8V

3

P-ON+5V(1)

4

GND

5

P-ON+5V

6

GND

7

GND

8

P-ON+1.2V

9

P-ON+10.5V

10

P-ON+1.2V

11

P-ON+10.5V

12

P-ON+1.2V

13

GND

14

GND

15

GND

16

CN2001

GND

17

GND

18

P-ON+3.3V

19

P-ON+3.3V

20

SDDAT1

21

P-ON+5V(2)

22

SDDAT0

23

WP

24

CD

25

SDDAT2

26

GND

27

SDDAT3

28

SDCLK

29

CMD

30

SPDIF

24

GND

23

P-ON+5V

22

P-ON+5V

21

AUDIO(R)-MUTE

20

AUDIO(L)-MUTE

19

AUDIO(R)

18

GND

17

AUDIO(L)

16

GND

15

GND

14

VIDEO

13

GND

12

VIDEO-Y(I/P)

11

CN2200

GND

10

VIDEO-Pb/Cb

9

GND

8

VIDEO-Pr/Cr

7

GND

6

CEC

5

SYS-RESET

4

RDY

3

SUB-TXD

2

SUB-RXD

1

W5

ETHERNET

HDMI

1
2
3
4

CN7601

5

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16

CN6101

17
18
19
20
21
22
23
24
25
26
27
28
29
30

1

2

3

4

5

6

7

8

9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

BD MAIN CBA

CN7101

JACK

CONNECTOR

EXPB(+)

EXPB(-)

EXPA(+)

EXPA(-)

SA-INT

THERMO

GND

RF(+)

RF(-)

GND

BDRF(+)

BDRF(-)

CN101CN301

GND

VC-PD

LD-TYPE

GND

+3.3V

GND

GND

GND

SD ATA 2

SCLK2

SEN-LDD

LDEN

TEST-V

FPIO1

SLD1(-)

SLD1(+)

SLD2(-)

SLD2(+)

VH(+)
HU(+)

HU(-)

HV(+)

HV(-)

CN302

HW(+)

HW(-)

VH(-)

TRAY-IN

TRAY-OUT

GND

LOAD(+)

LOAD(-)

FR2
FD2

FR1
FD1

+5V

+5V

+8V

PO0
PO1

1
2

TD

3

TR

4
5
6
7
8

9
10
11
12
13

F

14

A

15

E

16

B

17
18

C

19
20
21
22
23
24
25
26

D

27

G

28

H

29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45

1

2

3

4

W

2

V

3

U

4

5

6

7

8

9
10
11
12
13
14
15
16
17

LASER DIODE DRIVE

M

RELAY CBA

LENS DRIVEOEIC

SLED

BD-LD

CD-LD

PD-LD

DVD-LD

MOTOR

PICKUP

BD MAIN CBA & BD MECHANISM ASSEMBLY

M

SPINDLE

MOTOR

-OUT

TRAY

-IN

TRAY

M

LOADING

MOTOR

E5SK6WI1-13-1

SYSTEM CONTROL TIMING CHARTS

Power on

SLED moves

Start

SLED position

initialization

Pick-up position

moves

Power on

SLED moves

End

Hand close

Start

Hand close

detection

[ Tray Close ]

Start

Tray close

SLED position

initialization

Pick-up position

moves

[ Tray Close ]

End

Note:

If other sequence is received during the sequence,
it will stops and other sequence starts.
Only if SLED is moving, it will stop after the moving is finished.

[ Tray Open ]

Start

SLED inner

around moves

Tray open

[ Tray Open ]

End

1-14-1 B2N_TI

Parameter

V*: Voltage T*: Event timer

V0: 1.5 V T1: 0.3 s
V1: 6.8 V T3: 0.4 s

V2: 3.5 V T4: 2.0 s
V3: -3.5 V T5: 0.2 s
V4: -2.5 V T6: 3.0 s
V5: -6.8 V T7: 3.0 s

V6: 0.8 V T8: 2.0 s
V7: -4.0 V T9: 0.2 s

T10: 0.2 s

Tray-in-sw

Tray-out-sw

Tray ejection direction

Motor voltage 0[V]

Tray insertion direction

off

on

off

on

V1

V2

V0

If Tray-out-sw is not OFF
within T6, it is Time-out.

Tray open

T

8

T1

Time-out (T6)

If Tray-out-sw is not OFF
within T7, it is Time-out.

Time-out (T7) Time-out (T4)

Brake mode (T9)

(t) X V3 / (T3)

It raise up voltages until
Tray-in-sw is ON. If Tray-out-sw
is not ON within T4, it is retried.

Tray close

t

T30

Brake mode (T5)

V4

V3

V5

T10

V6

It raise up voltage until
Tray-in-sw is ON. If Tray-out-sw
is not ON within T4, it is retried.

T11
Time-out T4

If Tray-in-sw is not ON
within T11, it is Time-out.

Brake mode T5

V7

V5

1-14-2 B2N_TI

IC PIN FUNCTION DESCRIPTIONS

IC2000 (SUB MICRO CONTROLLER)

Pin

IN/

No.

OUT

1 IN AD-KEY1 Key Date Input
2 - NU Not Used
3 - NU Not Used
4 - NU Not Used
5 - NU Not Used
6 - VDD +3.3V Power Supply
7 - VDD +3.3V Power Supply
8 IN OSC2 Main Clock Input

9 OUT OSC1 Main Clock Output
10 - GND Ground
11 - GND Ground
12 - NU Not Used
13 - GND Ground

14 IN RESET

15 - NU Not Used
16 - NU Not Used
17 - NU Not Used

18 OUT SUB-TXD

19 IN SUB-RXD

20 OUT

21 - NU Not Used

22 IN RDY

23 OUT

24 OUT

25 OUT FAN-CONT Fan Motor Control Signal

26 OUT

27 IN REMOTE Remote Signal Input
28 - NU Not Used
29 - NU Not Used

30 OUT SD/HD

31 IN CEC-IN CEC Signal Input
32 OUT CEC-OUT CEC Signal Output
33 - NU Not Used

Signal

Name

VIDEO­MUTE

SYS­RESET

AUDIO­MUTE

STANDBY­LED

Function

Micro Controller Reset
Signal

Transmission Data to Main
Micro Controller

Transmission Data from Main
Micro Controller

Video Driver Mute Control
Signal

Ready/Busy communication
Control Signal

System Reset Signal

Audio Mute Control Signal

Standby LED Control Signal

Video Driver Filter Control
Signal

Pin

IN/

No.

OUT

34 - NU Not Used

35 -

36 -

37 OUT PWSW2 Power On Signal Output 2
38 OUT PWSW3 Power On Signal Output 3
39 OUT PWSW4 Power On Signal Output 4
40 OUT PWSW1 Power On Signal Output 1
41 IN MODE0 Mode Select 0
42 IN MODE1 Mode Select 1
43 IN MODE2 Mode Select 2
44 IN MODE3 Mode Select 3
45 OUT FL-SW FL On/Off Control Signal
46 - NU Not Used
47 OUT VFD-STB VFD Serial Interface Strove
48 OUT VFD-DAT VFD Serial Data
49 - NU Not Used
50 OUT VFD-CLK VFD Serial Clock
51 - NU Not Used
52 - NU Not Used
53 - NU Not Used
54 - NU Not Used
55 - NU Not Used
56 - NU Not Used
57 - NU Not Used
58 - NU Not Used
59 - NU Not Used
60 - NU Not Used
61 - GND Ground
62 - NU Not Used

63 IN SAFETY

64 - FAN-LOCK Not Used

Signal

Name

FLASH­SDA

FLASH­SCL

Function

Not Used

Not Used

Power Supply Failure
Detection

1-15-1 E5SK6PIN

IC5001 ( VFD DRIVER )

Pin

IN/

No.

OUT

1 - NU Not Used

2 - NU Not Used

3 - NU Not Used

4 - NU Not Used

5 IN OSC Oscillator Input

6 - NU Not Used

7 IN VFD-DIN Serial Data Input

8 IN VFD-CLK Serial Clock Input

9 IN VFD-STB Serial Interface Input
10 - NU Not Used
11 - NU Not Used
12 - VSS Ground
13 - VDD Power Supply
14
15 P2
16 P3
17 P4
18 P5
19 P6
20 P7
21 P8

OUT

22 P9
23 P10
24 P11
25 P12
26 P13
27 P14
28 P15
29 P16
30 - VEE Pull Down Level
31

OUT

32 P18
33 - NU Not Used
34 - NU Not Used

Signal

P1

P17

Name

Function

Segment Output
Serial Data Input

Segment Output
Serial Data Input

Pin

IN/

No.

OUT

35
36 7G
37 6G
38 5G

OUT

39 4G
40 3G
41 2G
42 1G
43 - VDD Power Supply

44 - VSS

Signal

Name

8G

Function

Grid Output

Ground

1-15-2 E5SK6PIN

LEAD IDENTIFICATIONS

2SA1980M Y
2SA1980MG-AT
2SC5343MG-AT

ECB

BD9321EFJ-E2
FA5573N-D1-TE1

8 5

1 4

ECB

PS2561A-1(W)

1

2

4

3

2SA1981Y-AT
2SC5344 Y
STB1277LY-AT

1: Anode
2: Cathode
3: Emitter
4: Collector

RA K

PST8229NR
PST8229UR

54

123

SL431A-AT

2SA1980SFY
2SC5343SFG
SRA2205SF
SRC1203SF

EB

C

48 33

49

64

116

SC16315

33

23

34

44

1

11

32

17

22

12

BH76071FJ-E2

14

1

2SK3561(Q, M)

GDS

UTC4580TEM101C77AGE1

8

85

14

7

Note:

A: Anode
K: Cathode
E: Emitter
C: Collector
B: Base
R: Reference
G: Gate
D: Drain
S: Source

1-16-1 E5SK6LE

Cabinet

EXPLODED VIEWS

B4

2L062

Power Supply CBA

2L062

F1001

W2

2L085

2L063

B12

B22

W1

2L082

A35

1B1

BD Main CBA &
BD Mechanism
Assembly

B5

FM1001

B35

B22

2L091

AC1001

2L061

2L082

A3

2L082

2L072

2L081

2L070

2L083

W5

2L061

A4

A6

Front-B CBA

A1X

W6

A6

A21

2L061

B24

AV CBA

A2

A6

A20

B16

Front-A CBA

See Electrical Parts List
for parts with this mark.

Some Ref. Numbers are
not in sequence.

1-17-1 E5SK6CEX

Packing

Lower Side Upper Side

S1-A

A16

A20

S8

X14

X1-A

X10

X19

X2-A

X34

S4

S2

S3

X21

X20

X6

S1-B

S5

Some Ref. Numbers
are not in sequence.

1-17-2 E5SK6PEX

MECHANICAL PARTS LIST

PRODUCT SAFETY NOTE: Products marked with a

# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.

NOTE: Parts that are not assigned part numbers
(---------) are not available.

Ref. No. Description Part No.

A1X FRONT ASSEMBLY E5SK6UD 1VM124781
A2 CHASSIS E5PG0UD 1VM021432M
A3 TOP COVER E5SK0UD 1VM124579
A4 REAR PANEL E5SK6UD 1VM229718
A6 FOOT K7010UA 0VM403657A
A16 REGISTRATION CARD(PHILIPS) A01F2UH 1EMN25799B
A20 BARCODE LABEL E5SK6UD ---------­A21 MODEL NO. LABEL E5SK6UD ---------­A35 TOPPER POP E5SK6UD ---------­2L061 SCREW C-TIGHT M3X6 E5610UD 0VM412937A
2L062 SCREW C-TIGHT M3X6 E5610UD 0VM412937A
2L063 SCREW C-TIGHT M3X6 E5610UD 0VM412937A
2L070 SCREW B-TIGHT M3X8 BIND HEAD+ GBHB3080
2L072 SCREW B-TIGHT M3X8 BIND HEAD+ GBHB3080
2L081 SCREW TAP TIGHT M3X5 BIND HEAD+BLK NI GBHC3050
2L082 SCREW TAP TIGHT M3X5 BIND HEAD+BLK NI GBHC3050
2L083 SCREW TAP TIGHT M3X5 BIND HEAD+BLK NI GBHC3050
2L085 SCREW S-TIGHT M3X10 E5610UD 0VM412936A
2L091 SCREW P-TIGHT D4X8 BIND HEAD+ GBJP4080
B4 POWER COVER E5PG0UD 1VM228156
B5 FAN COVER E5SK0UD 1VM333400
B12 MAIN PCB BRACKET E5P00UD 1VM329997
B35 FAN PLATE E5SK0UD 1VM435903
FM1001 DC FAN MOTOR ASB0412HA-9U51 MMEZ12DEL003
W5 WIRE ASSEMBLY USB 5P WX1E5SK0-007 WX1E5SK0-007
W6 WIRE ASSEMBLY PSV-CONTROL 6P

WX1E5SK0-003

PACKING

S1-A PAD L E5SK0UD 1VM333818
S1-B PAD R E5SK0UD 1VM333819
S2 GIFT BOX CARTON E5SK6UD 1VM333738
S3 SET BAG E5PG0UD 1VM433985
S4 SLEEVE CARTON E5SK0UD 1VM435660
S5 PAD E5SK0UD 1VM435682
S8 PAD(AV CORD) E5SK0UD 1VM436141

ACCESSORIES

X1-A# OWNERS MANUAL E5SK6UD 1VMN29535
X2-A QUICK GUIDE E5SK6UD 1VMN29536
X6 BATTERY GR03M XB0M371GLP01
X10 ACCESSORY BAG E5795ED 0VM416059
X14 AV CORD 1500/BLACK WPZ0152TM018
X19 REMOTE CONTROL UNIT NB540UD NB540UD
X20 WIRELESS LAN ADAPTOR WU5205 UWLUSBACM001
X21 DONGLE LABEL E5SK0UD ---------­X34 NETFLIX GUIDE E5PG0UD 1VMN28453

WX1E5SK0-003

20100518 1-18-1 E5SK6CA

ELECTRICAL PARTS LIST

PRODUCT SAFETY NOTE: Products marked with a

# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.

NOTES:

1. Parts that are not assigned part numbers (---------)
are not available.

2. Tolerance of Capacitors and Resistors are noted
with the following symbols.

C.....±0.25% D.....±0.5% F.....±1%

G.....±2% J......±5% K.....±10%

M.....±20% N.....±30% Z.....+80/-20%

BD MAIN CBA & BD MECHANISM
ASSEMBLY

Ref. No. Description Part No.

1B1 BD MAIN CBA & BD MECHANISM ASSEMBLY N7JP1CUN

AV ASSEMBLY

Ref. No. Description Part No.

AV ASSEMBLY
Consists of the following:

POWER SUPPLY CBA (AV PCB A)
AV CBA (AV PCB B)
FRONT-A CBA (AV PCB D)
FRONT-B CBA (AV PCB E)

POWER SUPPLY CBA

Ref. No. Description Part No.

POWER SUPPLY CBA (AV PCB A)
Consists of the following:

CAPACITORS

C1001 CERAMIC CAP. SL K 56pF/1KV CCD3AKPSL560
C1002# CAP METALIZED FILM 0.047µF/250V/K/MPX CT2E473EUR01
C1003# SAFETY CAP. 2200pF/250V CCG2EMA0F222
C1004 CHIP CERAMIC CAP.(1608) CH J 22pF/50V CHD1JJ3CH220
C1005 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1006 CHIP CERAMIC CAP.(1608) B K 0.033µF/50V CHD1JK30B333
C1007 SAFETY CAP. 2200pF/250V CCG2EMA0F222
C1009 ELECTROLYTIC CAP. 47µF/35V/M CEE47RENW016
C1010 METALIZED FILM CAP. 0.0022µF/400V K CT2H222DT034
C1011 ELECTROLYTIC CAPACITOR

C1013 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C1016 ELECTROLYTIC CAP. 47µF/16V/M CEC47RENW016
C1017# CAP METALIZED FILM 0.047µF/250V/K/MPX CT2E473EUR01
C1018 ELECTROLYTIC CAP. 1000µF/25V/M CED102ENW016
C1019 ELECTROLYTIC CAP 4700µF/6.3V SL CEA472ENW013
C1021 ELECTROLYTIC CAP. 33µF/50V/M CEF33RENW016
C1022 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C1024 ELECTROLYTIC CAP. 1000µF/25V/M CED102ENW016
C1025 ELECTROLYTIC CAP 3300µF/6.3V/M CEA332ENW013
C1026 ELECTROLYTIC CAP. 1000µF/25V/M CED102ENW016

ZR200TA151K16DB

1VSA25048

----------

----------

----------

----------

----------

CA2D151DYG03

Ref. No. Description Part No.

C1027 CHIP CERAMIC CAP. B K 0.068µF/50V CHD1JK30B683
C1033 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C1037 ELECTROLYTIC CAP. 47µF/6.3V/M CEA47RENW016
C1038 ELECTROLYTIC CAP. 10µF/50V M CEF10RENW016
C1039 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
C1040 ELECTROLYTIC CAP. 100µF/16V/M CEC101ENW016

CONNECTORS

CN1004 FFC CONNECTOR IMSA-9615S-06A-PP-A JC96J06ER007
CN1005 PH CONNECTOR TOP 2P B2B-PH-K-S

(LF)(SN)

J3PHC02JG029

DIODES

D1001 RECTIFIER DIODE 1N4005 NDQZ001N4005
D1002 RECTIFIER DIODE 1N4005 NDQZ001N4005
D1003 RECTIFIER DIODE 1N4005 NDQZ001N4005
D1004 RECTIFIER DIODE 1N4005 NDQZ001N4005
D1005 DIODE ZENER 27BSB-T26 NDTB027BST26
D1006 RECTIFIER DIODE BA159 NDQZ000BA159
D1007 RECTIFIER DIODE BA157 NDQZ000BA157
D1008 WIRE CP STP-S-0.60 XZ40F0REN002
D1009 DIODE ZENER 24BSB-T26 NDTB024BST26
D1010 RECTIFIER DIODE BA157 NDQZ000BA157
D1011 SCHOTTKY BARRIER DIODE SMD SK54 ND1Z0000SK54
D1013 SCHOTTKY BARRIER DIODE SB540-B/P NDLZ000SB540
D1014 SCHOTTKY BARRIER DIODE SB540-B/P NDLZ000SB540
D1017 DIODE ZENER 18BSC-T26 NDTC018BST26
D1018 RECTIFIER DIODE BA157 NDQZ000BA157
D1022 SCHOTTKY BARRIER DIODE SB140 NDQZ000SB140
D1023 SCHOTTKY BARRIER DIODE SMD SK39 ND1Z0000SK39
D1024 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F
D1036 DIODE ZENER 27BSB-T26 NDTB027BST26
D1037 DIODE ZENER 27BSB-T26 NDTB027BST26

ICS

IC1001# IC SWITCHING FA5573N-D1-TE1 SOP8 QSCA0T0FD002
IC1003# PHOTOCOUPLER PS2561A-1(W) QPEWPS2561A1
IC1011 IC SHUNT REGULATOR SL431A-AT NSZBA0TAUK01
IC1012 IC SHUNT REGULATOR SL431A-AT NSZBA0TAUK01

COILS

L1001# COIL LINE FILTER ST0603FT20-009 0.027 LLEB0Z0Y2001
L1003 POWER INDUCTORS CWKBNP-220K LLF2200KV002

TRANSISTORS

Q1001# MOS FET 2SK3561(Q.M) QFQZSK3561QM
Q1002 PNP TRANSISTOR 2SA1980M Y NQSY2SA1980M
Q1011 NPN TRANSISTOR 2SC5344 Y NQSY02SC5344

RESISTORS

R1001 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R1002 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R1003 CHIP RES. 1/10W J 8.2k Ω RRXAJR5Z0822
R1004 CHIP RES RMC1/8-104JTP RRX4JR7Z0104
R1005 CHIP RES. 1/10W J 10 Ω RRXAJR5Z0100
R1006 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R1008 CHIP RES. 1/10W J 56 Ω RRXAJR5Z0560
R1009 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R1011 CHIP RES. 1/10W J 10 Ω RRXAJR5Z0100
R1012 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R1013 METAL OXIDE FILM RES. 2W J 47k Ω RN02JZLZ0473
R1014 METAL OXIDE RES. 2W J 0.68 Ω RN02JZLZ0R68
R1016 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471
R1017 CHIP RES. 1/10W J 8.2k Ω RRXAJR5Z0822
R1019 CHIP RES. 1/10W J 680 Ω RRXAJR5Z0681

20100518 1-19-1 E5SK6EL

Ref. No. Description Part No.

R1020 CHIP RES. 1/10W F 2k Ω RRXAFR5H2001
R1021 CARBON RES. 1/4W J 1.5k Ω RCX4JATZ0152
R1023 CHIP RES. 1/10W J 5.1k Ω RRXAJR5Z0512
R1024 CHIP RES. 1/10W F 150 Ω RRXAFR5H1500
R1025 CHIP RES. 1/10W F 1.0k Ω RRXAFR5H1001
R1026 CHIP RES. 1/10W F 1.0k Ω RRXAFR5H1001
R1027 CARBON RES. 1/4W J 3.9k Ω RCX4JATZ0392
R1039 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R1040 CARBON RES. 1/4W J 100 Ω RCX4JATZ0101
R1046 CHIP RES. 1/10W F 2.2k Ω RRXAFR5H2201
R1048 CHIP RES. 1/10W F 3.3k Ω RRXAFR5H3301

MISCELLANEOUS

AC1001# AC CORD W/O A GND WIRE

F1001# FUSE TIME RAG TSC2.5A250VSVDEUC3CP PDGAAB0W3252
F1002 CHIP FUSE FCC16501ABTP PDDAEC0KE501
FH1001 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002
FH1002 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002
SA1001# SURGE ABSORBER PVR-10D221KB NVQZ10D221KB
T1001# TRANS POWER 0A523-S06 LTT2PC0KT062
W1 WIRE ASSEMBLY PSV-AV 11P WX1E5SK0-009 WX1E5SK0-009
W2 WIRE ASSEMBLY PSV-AV 11P WX1E5SK0-009 WX1E5SK0-009

PB8K9F9110AB057

WAC1720LW003

AV CBA

Ref. No. Description Part No.

AV CBA (AV PCB B)
Consists of the following:

CAPACITORS

C2009 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C2011 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C2012 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C2014 ELECTROLYTIC CAP. 22µF/50V/M CEF22RENW016
C2065 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C2100 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
C2104 ELECTROLYTIC CAP. 47µF/6.3V/M CEA47RENW016
C2106 CHIP CERAMIC CAP. CH D 8pF/50V CHD1JD3CH8R0
C2206 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C2207 ELECTROLYTIC CAP. 10µF/16V/M CEC10RENW016
C2208 ELECTROLYTIC CAP. 10µF/16V/M CEC10RENW016
C2209 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221
C2210 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221
C2211 ELECTROLYTIC CAP. 10µF/16V/M CEC10RENW016
C2212 ELECTROLYTIC CAP. 10µF/16V/M CEC10RENW016
C2213 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C2215 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390
C2216 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390
C2283 ELECTROLYTIC CAP. 220µF/6.3V/M CEA221ENW016
C2300 ELECTROLYTIC CAP. 100µF/6.3V/M CEA101ENW016
C2301 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C2303 ELECTROLYTIC CAP. 470µF/6.3V/M CEA471ENW016
C2304 ELECTROLYTIC CAP. 470µF/6.3V/M CEA471ENW016
C2305 ELECTROLYTIC CAP. 470µF/6.3V/M CEA471ENW016
C2306 ELECTROLYTIC CAP. 470µF/6.3V/M CEA471ENW016
C2307 ELECTROLYTIC CAP. 10µF/16V/M CEC10RENW016
C2319 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C2320 CHIP CERAMIC CAP.(1608) B K 1µF/10V CHD1AK30B105
C2321 CHIP CERAMIC CAP.(1608) B K 1µF/10V CHD1AK30B105
C2328 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C2601 ELECTROLYTIC CAP. 1000µF/6.3V/M CEA102ENW016
C2602 ELECTROLYTIC CAP. 1000µF/6.3V/M CEA102ENW016
C2605 ELECTROLYTIC CAP. 47µF/25V/M CED47RENW016
C2607 ELECTROLYTIC CAP. 1000µF/6.3V/M CEA102ENW016

----------

Ref. No. Description Part No.

C2608 ELECTROLYTIC CAP. 1000µF/6.3V/M CEA102ENW016
C2609 CHIP CERAMIC CAP.(1608) B K 1µF/10V CHD1AK30B105
C2616 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105
C2617 CHIP CERAMIC CAP.(2125) F Z 10µF/10V CHE1AZ30F106
C2618 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C2619 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C2620 CHIP CERAMIC CAP. B K 8200pF/50V CHD1JK30B822
C2622 CHIP CERAMIC CAP.(2125) F Z 10µF/10V CHE1AZ30F106
C2623 CHIP CERAMIC CAP.(2125) F Z 10µF/10V CHE1AZ30F106
C2626 ELECTROLYTIC CAP. 100µF/6.3V/M CEA101ENW016
C2627 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105
C2629 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C2630 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C2631 CHIP CERAMIC CAP.(1608) B K 5600pF/50V CHD1JK30B562
C2632 CHIP CERAMIC CAP.(2125) F Z 10µF/10V CHE1AZ30F106
C2633 CHIP CERAMIC CAP.(2125) F Z 10µF/10V CHE1AZ30F106
C2634 CHIP CERAMIC CAP.(2125) F Z 10µF/10V CHE1AZ30F106
C2638 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
C2639 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221
C2640 ELECTROLYTIC CAP. 100µF/16V/M CEC101ENW016
C2641 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105
C2642 CAP CHIP 2125 R6/K/10000000pF/16V CHM1060MR010
C2644 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C2645 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C2646 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C2647 CAP CHIP 2125 R6/K/10000000pF/16V CHM1060MR010
C2648 CAP CHIP 2125 R6/K/10000000pF/16V CHM1060MR010
C2651 ELECTROLYTIC CAP. 330µF/6.3V/M CEA331ENW016
C2652 ELECTROLYTIC CAP. 330µF/6.3V/M CEA331ENW016
C2653 ELECTROLYTIC CAP. 330µF/6.3V/M CEA331ENW016
C2655 ELECTROLYTIC CAP. 470µF/16V/M CEC471ENW016
C2660 ELECTROLYTIC CAP. 100µF/6.3V/M CEA101ENW016
C2661 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105
C2662 CHIP CERAMIC CAP.(2125) F Z 10µF/10V CHE1AZ30F106
C2664 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C2665 CHIP CERAMIC CAP.(1608) B K 3300pF/50V CHD1JK30B332
C2666 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C2667 CHIP CERAMIC CAP.(2125) F Z 10µF/10V CHE1AZ30F106
C2668 CHIP CERAMIC CAP.(2125) F Z 10µF/10V CHE1AZ30F106
C2670 ELECTROLYTIC CAP. 330µF/6.3V/M CEA331ENW016
C4001 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C4002 CHIP CERAMIC CAP.(2125) F Z 10µF/10V CHE1AZ30F106
C4008 CHIP CERAMIC CAP.(1608) CH J 33pF/50V CHD1JJ3CH330

CONNECTORS

CN2001 CONNECTOR PRINT OSU 30PIN IMSA-9195B-

CN2002 WIRE ASSEMBLY AV-VFD 10P WX1E5SK0-011 WX1E5SK0-011
CN2200 WIRE ASSEMBLY AV-MAIN 24P WX1E5PG0-

CN2300 CONNECTOR KAKU MES UJAP03B025-11-3 JBUA040WJ001
CN2301 CONNECTOR PRINT OSU B5B-PH-K-S

CN4000 CONNECTOR IC CARD MES 9PIN 1903572 JF19090AP001

30Z05

001

(LF)(SN)

J391300ER003

WX1E5PG0-001

J3PHC05JG029

DIODES

D2000 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F
D2025 RECTIFIER DIODE 1N4005 NDQZ001N4005
D2601 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F
D2605 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F
D2608 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F
D2609 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F
D2610 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F
D2612 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F
D2614 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F

20100518 1-19-2 E5SK6EL

Ref. No. Description Part No.

D2615 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F
D2620 SCHOTTKY BARRIER DIODE SMD SK34 ND1Z0000SK34
D2621 SCHOTTKY BARRIER DIODE SMD SK34 ND1Z0000SK34
D2622 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F
D2624 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F
D2640 SCHOTTKY BARRIER DIODE SMD SK34 ND1Z0000SK34
D2660 SCHOTTKY BARRIER DIODE SMD SK34 ND1Z0000SK34

ICS

IC2000 IC SUB MICON MN101C77AGE1 QSAA0R0MS019

Either IC2001 or IC2002 is used.

IC2001 RESET IC IC-PST8229NR QSZBA0TMM177
IC2002 IC (RESET) IC-PST8229UR QSCA0T0MM216
IC2200 IC OP AMP UTC4580TE NSCA0T02H001
IC2300 IC VIDEO DRIVER BH76071FJ-E2 QSCA0T0RM103
IC2601 IC DC-DC CONVERTER BD9321EFJ-E2 QSCA0T0RM102
IC2602 IC DC-DC CONVERTER BD9321EFJ-E2 QSCA0T0RM102
IC2640 IC DC-DC CONVERTER BD9321EFJ-E2 QSCA0T0RM102
IC2660 IC DC-DC CONVERTER BD9321EFJ-E2 QSCA0T0RM102

COILS

L2100 WIRE CP STP-S-0.60 XZ40F0REN002
L2201 POWER INDUCTORS CWKBNP-100K LLF1000KV002
L2202 POWER INDUCTORS CWKBNP-100K LLF1000KV002
L2300 RADIAL TYPE CHOKE COIL CW68-470K-

L2400 CHOKE COIL 22µH-K LLBD00PKV021
L2600 CHOKE COIL 22µH-K LLBD00PKV021
L2601 CHOKE COIL 22µH-K LLBD00PKV021
L2640 POWER INDUCTORS CWKBNP-100K LLF1000KV002
L2660 POWER INDUCTORS CWKBNP-100K LLF1000KV002
L4002 CHIP INDUCTOR LK160882NM-T LLACMB3TU82N

841040NP

LLBD00PKV023

TRANSISTORS

Q2002 PNP TRANSISTOR SMD 2SA1980SFY NQ1Y2SA1980S
Q2003 TRANSISTOR SRC1203SF NQ1ZSRC1203S
Q2004 NPN TRANSISTOR 2SC5344 Y NQSY02SC5344
Q2006 PNP TRANSISTOR SMD 2SA1980SFY NQ1Y2SA1980S
Q2007 NPN TRANSISTOR SMD 2SC5343SFG NQ1G2SC5343S
Q2008 NPN TRANSISTOR SMD 2SC5343SFG NQ1G2SC5343S
Q2009 NPN TRANSISTOR SMD 2SC5343SFG NQ1G2SC5343S
Q2010 NPN TRANSISTOR SMD 2SC5343SFG NQ1G2SC5343S
Q2100 NPN TRANSISTOR SMD 2SC5343SFG NQ1G2SC5343S
Q2200 PNP TRANSISTOR DIGITAL SMD SRA2205SF NQ1ZSRA2205S
Q2201 PNP TRANSISTOR DIGITAL SMD SRA2205SF NQ1ZSRA2205S
Q2202 NPN TRANSISTOR 2SC5343MG-AT NQSG2SC5343M
Q2203 NPN TRANSISTOR 2SC5343MG-AT NQSG2SC5343M
Q2601 NPN TRANSISTOR SMD 2SC5343SFG NQ1G2SC5343S
Q2603 PNP TRANSISTOR 2SA1981Y-AT NQSY02SA1981
Q2604 PNP TRANSISTOR STB1277LY-AT NQSYSTB1277L
Q2605 NPN TRANSISTOR 2SC5344 Y NQSY02SC5344
Q2606 PNP TRANSISTOR STB1277LY-AT NQSYSTB1277L
Q2608 PNP TRANSISTOR 2SA1980MG-AT NQSG2SA1980M
Q2609 NPN TRANSISTOR SMD 2SC5343SFG NQ1G2SC5343S
Q2619 NPN TRANSISTOR SMD 2SC5343SFG NQ1G2SC5343S
Q2620 NPN TRANSISTOR SMD 2SC5343SFG NQ1G2SC5343S
Q2621 NPN TRANSISTOR SMD 2SC5343SFG NQ1G2SC5343S

RESISTORS

R2001 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2002 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R2003 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R2004 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471
R2007 CHIP RES. 1/10W J 15k Ω RRXAJR5Z0153
R2010 CHIP RES. 1/10W J 470k Ω RRXAJR5Z0474
R2012 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R2013 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101

Ref. No. Description Part No.

R2014 CARBON RES. 1/4W J 2.2 Ω RCX4JATZ02R2
R2015 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R2016 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R2018 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R2019 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R2020 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2021 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2023 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R2024 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2025 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2026 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2027 WIRE CP STP-S-0.60 XZ40F0REN002
R2029 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2031 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2035 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2036 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2038 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R2040 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2041 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2042 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2043 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2049 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2053 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R2063 CARBON RES. 1/4W J 240 Ω RCX4JATZ0241
R2064 CARBON RES. 1/4W J 240 Ω RCX4JATZ0241
R2066 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R2067 CHIP RES. 1/10W J 5.6k Ω RRXAJR5Z0562
R2069 CARBON RES. 1/4W J 120 Ω RCX4JATZ0121
R2070 CARBON RES. 1/4W J 120 Ω RCX4JATZ0121
R2076 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R2077 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R2078 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R2082 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R2091 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R2100 CHIP RES. 1/10W J 2k Ω RRXAJR5Z0202
R2101 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R2102 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R2103 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221
R2104 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R2105 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R2201 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R2208 CHIP RES. 1/10W F 24k Ω RRXAFR5H2402
R2209 CHIP RES. 1/10W F 24k Ω RRXAFR5H2402
R2210 CHIP RES. 1/10W J 8.2k Ω RRXAJR5Z0822
R2211 CHIP RES. 1/10W J 8.2k Ω RRXAJR5Z0822
R2212 CHIP RES. 1/10W F 33.0k Ω RRXAFR5H3302
R2213 CHIP RES. 1/10W F 33.0k Ω RRXAFR5H3302
R2214 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R2215 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R2216 CHIP RES. 1/10W J 820 Ω RRXAJR5Z0821
R2217 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R2218 CHIP RES. 1/10W J 820 Ω RRXAJR5Z0821
R2219 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R2220 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R2221 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R2223 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R2224 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R2226 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R2227 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221
R2228 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221
R2229 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R2230 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R2301 CHIP RES.(1608) 1/10W F 82.0 Ω RRXAFR5H82R0

20100518 1-19-3 E5SK6EL

Ref. No. Description Part No.

R2302 CHIP RES.(1608) 1/10W F 82.0 Ω RRXAFR5H82R0
R2303 CHIP RES.(1608) 1/10W F 82.0 Ω RRXAFR5H82R0
R2304 CHIP RES.(1608) 1/10W F 82.0 Ω RRXAFR5H82R0
R2305 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R2306 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R2307 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R2310 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R2311 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R2312 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R2313 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R2601 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R2606 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R2607 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R2608 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R2609 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R2612 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2621 CARBON RES. 1/4W J 82 Ω RCX4JATZ0820
R2622 CARBON RES. 1/4W J 82 Ω RCX4JATZ0820
R2625 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R2626 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R2637 METAL OXIDE FILM RES. 1W J 1.2 Ω RN01JZLZ01R2
R2638 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2639 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2642 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R2643 CHIP RES. 1/10W F 2.2k Ω RRXAFR5H2201
R2644 CHIP RES. 1/10W F 33.0k Ω RRXAFR5H3302
R2645 CHIP RES. 1/10W F 3.3k Ω RRXAFR5H3301
R2646 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R2654 CHIP RES. 1/10W J 5.1k Ω RRXAJR5Z0512
R2655 CHIP RES. 1/10W J 8.2k Ω RRXAJR5Z0822
R2660 CHIP RES. 1/10W F 1.5k Ω RRXAFR5H1501
R2661 CHIP RES. 1/10W F 3.3k Ω RRXAFR5H3301
R2662 CHIP RES. 1/10W F 1.5k Ω RRXAFR5H1501
R2663 CHIP RES. 1/10W F 2.2k Ω RRXAFR5H2201
R2664 CHIP RES. 1/10W F 3.3k Ω RRXAFR5H3301
R2665 CHIP RES. 1/10W J 15k Ω RRXAJR5Z0153
R2666 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R2667 CHIP RES. 1/10W F 9.1k Ω RRXAFR5H9101
R2668 CHIP RES. 1/10W F 3.3k Ω RRXAFR5H3301
R2669 CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273
R2671 CHIP RES. 1/10W J 220k Ω RRXAJR5Z0224
R2673 CHIP RES. 1/10W J 2.2M Ω RRXAJR5Z0225
R2674 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R2675 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221
R2676 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R2678 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R2679 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R2680 CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273
R2701 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R2702 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R2703 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R4001 CHIP RES. 1/10W J 47 Ω RRXAJR5Z0470
R4002 CHIP RES. 1/10W J 47 Ω RRXAJR5Z0470
R4003 CHIP RES. 1/10W J 47 Ω RRXAJR5Z0470
R4004 CHIP RES. 1/10W J 22 Ω RRXAJR5Z0220
R4005 CHIP RES. 1/10W J 47 Ω RRXAJR5Z0470
R4006 CHIP RES. 1/10W J 47 Ω RRXAJR5Z0470

MISCELLANEOUS

B22 HIMELON TAPE(5X40) E5PJ0UD 1VM434141
JK2100 RCA JACK(BLACK) MSP-251V-01 NI FE LF JXRL010LY125
JK2300 RCA JACK MSD-246V-65 NI FE LF JXRL060LY131
X2000 CERAMIC RESONATOR ZTT8.00MT47 FY0805PLN004

FRONT-A CBA

Ref. No. Description Part No.

FRONT-A CBA (AV PCB D)
Consists of the following:

----------

CAPACITORS

C5002 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C5006 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C5007 ELECTROLYTIC CAP. 100µF/6.3V/M/H7 CEA101ENW025

CONNECTOR

CN5000 CONNECTOR PRINT MES 00 6203 301 010

000+

JC62100UG016

IC

IC5001 VFD DRIVER IC SC16315 NSZBA0TQ0010

COIL

L5000 INDUCTOR(100µH K) LAP02TA101K LLAXKATTU101

RESISTORS

R5007 CHIP RES. 1/10W J 68k Ω RRXAJR5Z0683
R5012 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682

MISCELLANEOUS

B16 FOOT K7010UA 0VM403657A
B24 HIMELON TAPE(6X16) E5PJ0UD 1VM434168
FL5001 FL 8-ST-30NK TVFD1C0FT059
RS5000 SENSOR REMOTE RECEIVER KSM-712TC2M USEJRS0KK002

FRONT-B CBA

Ref. No. Description Part No.

FRONT-B CBA (AV PCB E)
Consists of the following:

CONNECTOR

CN3004 FFC CONNECTOR 6P IMSA-9615S-06C-PP-A JC96J06ER009

DIODE

D3009 LED(RED) LTL-1CHEE NPQZLTL1CHEE

RESISTORS

R3010 CHIP RES. 1/10W J 120 Ω RRXAJR5Z0121
R3024 CHIP RES. 1/10W J 180 Ω RRXAJR5Z0181
R3025 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221
R3026 CHIP RES. 1/10W J 330 Ω RRXAJR5Z0331
R3027 CHIP RES. 1/10W J 5.6k Ω RRXAJR5Z0562

SWITCHES

SW3007 TACT SWITCH SKQSAB SST0101AL038
SW3008 TACT SWITCH SKQSAB SST0101AL038
SW3009 TACT SWITCH SKQSAB SST0101AL038
SW3010 TACT SWITCH SKQSAB SST0101AL038
SW3011 TACT SWITCH SKQSAB SST0101AL038

----------

20100518 1-19-4 E5SK6EL

© 2010 Funai Electric Co., Ltd.

All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.

Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.

with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.

BDP5320/F7

E5SK6UD

2010-06-03