Philips AZ1046 User Manual

Document order number:

000000000000

AZ1046/12

EN User manual 4

Contents

Program play sequence 29 Listen to radio

1 Important 6

Safety 6 Notice 12

2 Your CD Soundmachine Dynamic Bass

Boost 16

Introduction 16 What’s in the box Overview of the main unit

17 17

3 Get started 21

Install batteries Connect AC power

21 23

4 Use your soundmachine 25

Play a CD Select a track Select an album Find a passage within a track Select play modes

25 26 26 27 27

5 Troubleshooting 33

6 Product information 36

1 Important

Safety

a Read these instructions. b Keep these instructions. c Heed all warnings. d Follow all instructions. e Do not use this apparatus near water. f Clean only with dry cloth. g Do not block any ventilation openings.

Install in accordance with the manufacturer’s instructions.

h Do not install near any heat sources such

as radiators, heat registers, stoves, or

other apparatus (including ampliers) that

produce heat.

i For countries with a polarized mains, do not

defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your

safety. If the provided plug does not t

into your outlet, consult an electrician for replacement of the obsolete outlet. Caution: To prevent electric shock, match the wide blade of the plug to the wide slot, fully insert.

j Protect the power cord from being

walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

k Only use attachments/accessories specied

by the manufacturer.

l Use only with the cart, stand, tripod,

bracket, or table specied by the

manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

m Unplug this apparatus during lightning

storms or when unused for long periods of time.

n Refer all servicing to qualied service

personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

o Battery usage CAUTION – To prevent

battery leakage which may result in bodily injury, property damage, or damage to the unit:

•

Install all batteries correctly, + and - as marked on the unit. Do not mix batteries (old and new or

• carbon and alkaline, etc.). Remove batteries when the unit is not

• used for a long time.

p Apparatus shall not be exposed to dripping

or splashing.

q Do not place any sources of danger on the

apparatus (e.g. liquid lled objects, lighted candles).

r This product may contain lead and

mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org.

How to connect a plug

The wires in the mains lead are coloured with the following code: blue = neutral (N), brown = live (L).

As these colours may not correspond with the colour markings identifying the terminals in your plug, proceed as follows:

Connect the blue wire to the terminal

• marked N or coloured black. Connect the brown wire to the terminal

• marked L or coloured red. Do not connect either wire to the earth

• terminal in the plug, marked E (or e) or coloured green (or green and yellow). Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the two wires.

Mains plug

This apparatus is tted with an approved 13 Amp

plug. To change a fuse in this type of plug proceed as follows:

a Remove fuse cover and fuse. b Fix new fuse which should be a BS13625

Amp, A.S.T.A. or BSI approved type.

c Ret the fuse cover.

If the tted plug is not suitable for your socket

outlets, it should be cut off and an appropriate

plug tted in its place.

If the mains plug contains a fuse, this should have a value of 5 Amp. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp. The severed plug must be disposed off to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere.

+ 14 hidden pages