Philips AZ1024 User Manual

CD Soundmachine

www.philips.com/welcome

User Manual

AZ102C

AZ102N

AZ102S

Meet Philips at the Internet

http://www.philips.com

Printed in China PDCC-ZC-0735

CLASS 1

LASER PRODUCT

AZ102C

AZ102N

AZ102S

6 x R14 • UM-2 • C-CELLS

BAND

M W

O F F

M W

F M

C D

D BB

OFF

L IN

Important notes for users in the U.K.

Mains plug

This apparatus is fitted with an approved 13 Amp plug.To change a fuse in this type of

plug proceed as follows:

1. Remove fuse cover and fuse.

2. Fix new fuse which should be a BS1362 3 Amp, A.S.T.A. or BSI approved type.

3. Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut off and an

appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a

value of 3 Amp. If a plug without a fuse is used, the fuse at the distribution board

should not be greater than 3 Amp.

Note:The severed plug must be disposed of to avoid a possible shock hazard should it

be inserted into a 13 Amp socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured with the following code: blue = neutral (N),

brown = live (L). As these colours may not correspond with the colour markings

identifying the terminals in your plug, proceed as follows:

• Connect the blue wire to the terminal marked N or coloured black.

• Connect the brown wire to the terminal marked L or coloured red.

• Do not connect either wire to the earth terminal in the plug, marked E (or e) or

coloured green (or green and yellow).

Before replacing the plug cover, make certain that the cord grip is clamped over the

sheath of the lead - not simply over the two wires.

Recording and playback of material may require consent. See Copyright Act 1956 and

The Performer’s Protection Acts 1958 to 1972.

Congratulations on your purchase and

welcome to Philips!

To fully benefit from the support that

Philips offers, register your product at

www.philips.com/welcome.

Supplied Accessories

– AC power cord

Top/front panels (See 1)

VOLUME

– adjusts volume level.

SHUFFLE –

plays all tracks in random order

3 REPEAT

– repeats a track/

CD program/entire CD.

2 ;

– starts or pause CD playback

§ ∞

– selects the next/previous track

– searches forwards/backwards (press and

hold the button) within the current track

– stops CD playback;

– erases a CD program

5 PROG – programs tracks and reviews the

program

6 LIFT TO OPEN – opens/closes the CD

door.

7 TUNING

– tunes to radio stations

Display

– shows the CD functions

Back panel (See 1

and

Source selector: CD, FM, MW, OFF

– selects CD or radio source of sound

– power off switch

0 Telescopic antenna - improves FM reception.

! AC MAINS~ - inlet for power cord.

DBB

– turns the bass enhancement on/off.

LINE-IN

– inlet for external audio source.

Bottom panel

Battery door –

Press on the arrow and

push to

to insert 6 x 1.5V R-14/ UM-2/ C-

cells

CAUTION

- Visible and invisible laser radiation.

If the cover is open, do not look at

the beam.

- High voltage! Do not open.You run

the risk of getting an electric shock.

The machine does not contain any

user-serviceable parts.

- Modification of the product could

result in hazardous radiation of

EMC or other unsafe operation.

- Use of controls or adjustments or

performance of precedures other

than herein may result in unsafe

operation.

This set complies with the radio

interference requirements of the

European Union.

Power Supply

Whenever convenient, use the power supply

cord if you want to conserve battery life.

Make sure you remove the plug from the set

and wall outlet before inserting batteries.

Batteries (not included)

1 Open the battery door and insert 6 batteries,

type R-14, UM-2 or C-cells, (preferably

alkaline) with the correct polarity as indicated by

the "+" and "–" symbols inside the compartment.

2 Replace the battery door, making sure the

batteries are firmly and correctly in place. The

set is now ready to operate.

Batteries contain chemical substances, so

they should be disposed of properly.

• Incorrect use of batteries can cause electrolyte

leakage and will corrode the compartment or

cause the batteries to burst:

• Do not mix battery types: e.g. alkaline with

carbon zinc. Only use batteries of the same type

for the set.

• When inserting new batteries, do not try to mix

old batteries with the new ones.

• Remove the batteries if the set is not to be used

for a long time.

English Controls/Power Supply

Power Supply General Operation / Tuner

Using AC power

WARNING:Always check you have

completely switched off the set, before

you change or disconnect power supply.

1 Check if the power voltage, as shown on

the type plate located on the

bottom of the set, corresponds to your

local power supply. If it does not, consult your

dealer or service center.

2 Connect the power cord to the AC

MAINS~ inlet and the wall socket.The set is

now connected and ready for use.

3 To switch the set off completely, withdraw the

power cord from the wall socket.

4 Install the unit near the AC outlet and where

the AC power plug can be easily reached.

• Disconnect the power cord from the wall

socket to protect your set during heavy

thunderstorms. Children could seriously injure

themselves as the free end of the cable may

still be live if only the connector is removed

from the MAINS socket at the back of the

unit.

The type plate is located on the

bottom of the set.

Helpful hints:

– To avoid unnecessary energy consumption,

always adjust the

Source selector

OFF

after using the set.

General operation

Switching on and off and selecting the

function

1 To select your sound source, adjust the

Source selector to: CD, FM or

MW.

2 To switch off the set, adjust the Source

selector to

OFF

position.

Adjusting volume and sound

Adjust the sound with the VOLUME and

DBB controls.

Radio reception

1 Adjust the Source selector to FM or

MW.

2 Tur n TUNING to tune to a station.

Helpful hints:

To improve radio reception

• For FM, extend, incline and turn the

telescopic antenna for best reception. Reduce

its length if the signal is too strong.

• For MW, the set uses a built-in antenna.

Direct this antenna for best reception by

turning the whole set.

PROG

ALL

Az102_ 05_Eng 2007.8.28 11:41 Page 1

CD SOUNDMACHINE AZ102N

VOLUME

DYNAMIC BASS BOOST

TUNING

Playing a CD

• This CD player plays Audio Discs including

CD-Recordables (CD-R) and CD-Rewritables

(CD-RW).

• MP3, CD-ROM, CD-I, CDV,VCD, DVD or

computer CDs are not possible for playback.

IMPORTANT!

CDs encoded with copyright protection

technologies by some record companies may

be unplayable by this product.

1 Adjust the Source selector to CD.

2 Open the CD door, and insert a CD with

the printed side facing up, then press the CD

door gently to close.

➜ Display shows --, and later the total

number of tracks. (See 3)

3 Press

to start playback.

4 To pause playback, press

➜

Display: 2 flashes.

(See 4)

5 To resume, press

again.

6 To stop CD playback, press

Helpful hints:

CD play will also stop when:

– you open the CD door ;

– you select

OFF

sound source;

–

the CD has reached the end.

Selecting a different track

• Press

∞/ §

once or repeatedly until the

desired track number appears in the display.

• In the pause/stop position, press 2; to start

playback.

Finding a passage within a

track

1 During playback, press and hold ∞ or § .

➜ The CD is played at high speed and with

reduced volume.

2 When you recognize the passage you want,

release ∞ or § to resume normal playback.

Helpful hints:

–

When your searching reaches the end of the

last track, the CD goes to stop mode.

Programming track

numbers

You may store up to 20 tracks in the desired

sequence. If you like, store any track more

than once.

1 In the stop position, press PROG to

activate programming.

➜ Display: PROG and 00 flash. (See 5)

2 Press

∞

to select your desired track

number.

3 Press PROG to store the desired track

number.

➜ Display: PROG and 00 flash for you to

program the next track..

4 Repeat steps 2 to 3 to select and store all

desired tracks in this way.

➜ If you attempt to store more than 20

tracks, no track can be selected and the

display shows

---- .

5 To play your program, press

;

Helpful hints :

– When playback of your program comes

to the stop position, your set will return

to normal playback.To re-enter program

mode, press PROG in the stop position.

Reviewing the program

In the stop position, press PROG repeatedly

to see your stored tracks.

Erasing a program

You can erase the contents of the memory

by:

– in the stop position, press PROG to enter

program mode, and then press

– selecting

OFF

;

– opening the CD door;

Different play modes:

REPEAT. and SHUFFLE

(See 6

, 7)

REPEAT

You can play the current track or the whole

disc repeatedly, and combine REPEAT

modes with PROG (PROGRAM).

REP – plays the current track continuously.

REP ALL – repeats the entire CD/program

1 To select play mode, press REPEAT once

or more.

➜ The display shows REP icon or REP

ALL icon.

2 Press 2; to start playback if in the stop/pause

position.

3 To return to normal playback, press REPEAT

repeatedly until the modes are no longer

displayed.

– You can also press 9 to cancel your play

mode.

SHUFFLE

Yo u can play all the tracks in random order.

1 In the stop position, press SHUFFLE to

switch on shuffle play.

➜ Display shows SHUFFLE icon.

2 To switch off shuffle play, press 9.

Helpful hints:

– During the shuffle play, when REP function is

selected, it will play the current shuffled track

repeatedly, or when the REP ALL function is

selected, it will repeat the shuffle play of the

entire CD.

CD Player

CD player and CD handling

• If the CD player cannot read CDs correctly,

use a cleaning CD to clean the lens before

taking the set to repair.

• The lens of the CD player should never be

touched!

• Sudden changes in the surrounding

temperature can cause condensation on the

lens of your CD player. Playing a CD is then

not possible. Do not attempt to clean the

lens but leave the set in a warm environment

until the moisture evaporates.

•Always close the CD door to avoid dust on

the lens.

•To clean the CD, wipe in a straight line from

the center towards the edge using a soft,

lint-free cloth. Do not use cleaning agents as

they may damage the disc.

• Never write on a CD or attach any stickers

to it.

Safety information

• Place the set on a flat, hard and stable surface

so that the system does not tilt.

• Where the MAINS plug or an appliance

coupler is used as the disconnect device, the

disconnet device shall remain readily

operable.

• Do not expose the set, batteries, CDs to

humidity, rain, sand or excessive heat caused

by heating equipment or direct sunlight.

• The apparatus shall not be exposed to

dripping or splashing.

• Adequate ventilation with a minimum gap of

15cm (6 inches) between the ventilation

holes and surrounding surfaces is necessary

to prevent heat build-up.

• Do not cover the ventilation openings with

items such as newspapers, table-cloths,

curtains, etc.

• No objects filled with liquids, such as vases,

shall be placed on the apparatus.

• No naked flame sources, such as lighted

candles, should be placed on the apparatus.

• The mechanical par ts of the set contain self-

lubricating bearings and must not be oiled or

lubricated.

•To clean the set, use a dry cloth. Do not use

any cleaning agents containing alcohol,

ammonia, benzene or abrasives as these may

harm the housing.

Maintenance & Safety (See 8)

Environmental information

All unnecessary packaging material has been omitted.The packaging can be easily separated

into three materials: cardboard, polystyrene and plastic.

Yo ur set consists of materials which can be recycled if disassembled by a

specialized company. Please observe the local regulations regarding the

disposal of packaging, dead batteries and old equipment.

Disposal of your old product

Your product is designed and manufactured with high quality

materials and components, which can be recycled and reused.

When this crossed-out wheeled bin symbol is attached to

a product it means the product is covered by the

European Directive 2002/96/EC.

Please inform yourself about the local separate collection system for electrical

and electronic products.

Please act according to your local rules and do not dispose of your old products

with your normal household waste.The correct disposal of your old product will

help prevent potential negative consequences for the environment and human

health.

Problem

– Possible cause

• Remedy

No sound /power

– Volume not adjusted

• Adjust the VOLUME

– Power cord not securely connected

• Connect the AC power cord properly

– Batteries dead/ incorrectly inserted

• Insert (fresh) batteries correctly

– Headphones connected to the set

• Disconnect headphones.

– CD contains non-audio files

• Press

∞ , §

once or more to skip to a CD audio

track, instead of the data file.

Display does not function properly / No

reaction to operation of any of the

controls

– Electrostatic discharge

• Switch off and unplug the set. Reconnect after a

few seconds

--, Er

01 indication

– No CD inserted

• Insert a CD

– CD badly scratched or dirty

• Replace/ clean CD, see Maintenance

– Laser lens steamed up

•Wait until lens has cleared

– CD-R/CD-RW is blank or not finalized

• Use a finalized CD-R/CD-RW or suitable CD

Audio disc only

Note:

Make sure the CD is not encoded with

do not conform to the Compact Disc

standard.

The CD skips tracks

– CD damaged or dirty

• Replace or clean CD

– Program/shuffle is active

• Quit program/shuffle mode

Note: A CD badly scratch or dirty may result in

improper operation.

Troubleshooting

If a fault occurs, first check the points listed below before taking the set for repair.

If you are unable to remedy a problem by following these hints, consult your dealer or service centre.

WARNING: Do not open the set as there is a risk of electric shock. Under no

circumstances should you try to repair the set yourself, as this will

invalidate the guarantee.

Notes

PROG

ALL

Az102_ 05_Eng 2007.8.28 11:41 Page 2