IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings.Install in
8. Do not install near any heat sources such as radiators, heat regis-
9. Only use attachments/accessories specified by the manufacturer.
LIFT
LOCK
PHILIPS CONSUMER ELECTRONICS NORTH AMERICA
Knoxville, Tennessee 37914-1810, U.S.A.
Audio
Audio
Read this manual first!
If you have any problems, do not attempt
to return this product to the store.
For fast help, call us first!
1-800-531-0039
S
E
E
W
H
Y
I
N
S
I
D
E
I
M
P
O
R
T
A
N
T
!
Return
your Warranty
Registration Card
within 10 days
Portable CD Pla yer
AX3211, AX3212, AX3213, AX3214, AX3215
AX3216, AX3217, AX3218, AX3219, AX3220
AX3221, AX3222, AX3223, AX3224, AX3225
#
%
$
2
3
4
5
1
8
7
6
9
0
!
@
1
CLASS 1
LASER PRODUCT
BELT CLIP
LIFT
LOCK
RELEASE
Audio
Audio
Read this manual first!
If you have any problems, do not attempt
to return this product to the store.
For fast help, call us first!
1-800-531-0039
S
E
E
W
H
Y
I
N
S
I
D
E
I
M
P
O
R
T
A
N
T
!
Return
your Warranty
Registration Card
within 10 days
Portable CD Pla yer
AX3211, AX3212, AX3213, AX3214, AX3215
AX3216, AX3217, AX3218, AX3219, AX3220
AX3221, AX3222, AX3223, AX3224, AX3225
2
1 OPEN
2
3
CD
5
HOLD➟
OFF
6
PLA
Y
7 VOLUME
AA
LR6
UM3
!!!
2.
1.
1.
2.
44
0
V
O
L
.
R
E
M
S
U
O
F
F
•
E
•
L
H
O
D
L
I
N
E
O
U
T
/
#
%
$
2
3
4
5
1
8
7
6
9
0
!
@
1
CLASS 1
LASER PRODUCT
BELT CLIP
LIFT
LOCK
RELEASE
QUICK START MISE EN SERVICE RAPIDE ENCENDIDO RAPIDO
Audio
Audio
Read this manual first!
If you have any problems, do not attempt
to return this product to the store.
For fast help, call us first!
1-800-531-0039
S
E
E
W
H
Y
I
N
S
I
D
E
I
M
P
O
R
T
A
N
T
!
Return
your Warranty
Registration Card
within 10 days
Portable CD Pla yer
AX3211, AX3212, AX3213, AX3214, AX3215
AX3216, AX3217, AX3218, AX3219, AX3220
AX3221, AX3222, AX3223, AX3224, AX3225
Batteries (supplied or optionally available)
You can use the following batteries with this CD-player:
• normal batteries type LR6, UM3 or AA (preferably Philips), or
• alkaline batteries type LR6, UM3 or AA (preferably Philips).
Notes:–
Inserting batteries
1 Push OPEN 2 to open the CD lid.
2 Open the battery compartment and insert either 2
Battery indication
The approximate power level of your batteries is shown
in the display.
Average playing time of batteries under normal conditions
Battery type ESP on Power Save
Normal 5 hours 6 hours
Alkaline 16 hours 20 hours
Batteries contain chemical substances, so they should be disposed
of properly.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings.Install in
accordance with the manufacturers instructions.
8. Do not install near any heat sources such as radiators, heat regis-
ters, stoves,or other apparatus (including amplifier s) that produce heat.
9. Only use attachments/accessories specified by the manufacturer.
10. Use only with a cart, stand, tripod, br acket, or table
specified by the manufacturer or sold with the apparatus.
When a cart is used, use caution when moving the
cart/appar atus combination to avoid injur y from tip-over.
11. Refer all servicing to qualified ser vice per sonnel. Ser vicing is
required when the apparatus has been damaged in any way,such as if
the power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus,or when the appar atus has been
exposed to rain or moisture, does not operate normally,or has been
dropped.
12. Batter y usage
CAUTION
– To prevent battery leakage which
may result in bodily injury,property damage or damage to the unit:
● Install ALL batteries correctly,+ and - as marked on the unit.
● Do not mix batteries (OLD and NEW or CARBON and
ALKALINE, etc.).
● Remove batteries when the unit is not used for a long time.
EL 6474-E004: 02/8
Return your Warranty Registration card today to
BELT CLIP
LIFT
LOCK
RELEASE
ensure you receive all the benefits you’re entitled to.
• Once your Philips purchase is registered,you’re eligible to receive all the
privileges of owning a Philips product.
Warranty
Verification
Registering your product
within 10 days confirms
your right to maximum
protection under the
terms and conditions of
your Philips warranty.
Confirmation
Your completed
Warranty Registration
Card serves as verification of ownership in the
event of product theft
or loss.
• So complete and return the Warranty
Registration Card enclosed with your
purchase at once, and take advantage
of these important benefits.
Owner
Model
Registration
Returning your Warranty
Registration Card right
away guarantees you’ll
receive all the information
and special offers which
you qualify for as the
owner of your model.
Know these
safety
CAUTION
RISK OF ELECTRIC SHOCK
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This “bolt of lightning”
indicates uninsulated material
within your unit may cause an
electrical shock.For the safety of
everyone in your household,please
do not remove product covering.
The “exclamation point” calls
attention to features for which
you should read the enclosed literature closely to prevent operating and
maintenance problems.
symbols
DO NOT OPEN
For Customer Use
Enter below the Serial No.which is
located on the rear of the cabinet.Retain
this information for future reference.
Model No. _____________________
Serial No. ______________________
WARNING: TO PREVENT FIRE
OR SHOCK HAZARD, DO NOT
EXPOSE THIS EQUIPMENT TO RAIN
OR MOISTURE.
CAUTION: To prevent electric
shock,match wide blade of plug to
wide slot,and fully insert.
MAC5097
LIMITED WARRANTY
PORTABLE COMPACTDISC
One Year Free Exchange
This product must be carried in for an exchange.
WHO IS COVERED?
You must have proof of purchase to exchange the product.A sales receipt or other document showing that you purchased the product is considered proof of purchase. Attach it
to this owner’s manual and keep both nearby.
WHATIS COVERED?
Warranty coverage begins the day you buy your product.For one year thereafter, a
defective or inoperative product will be replaced with a new, renewed or comparable
product at no charge to you.A replacement product is covered only for the original warranty period.When the warranty on the original product expires, the warranty on the
replacement product also expires.
WHATIS EXCLUDED?
Your warranty does not cover:
• labor charges for installation or setup of the product,adjustment of customer controls
on the product,and installation or repair of antenna systems outside of the product.
• product repair and/or part replacement because of misuse,accident,unauthorized repair
or other cause not within the control of Philips.
• reception problems caused by signal conditions or cable or antenna systems outside
the unit.
• a product that requires modification or adaptation to enable it to operate in any country other than the country for which it was designed, manufactured, approved and/or
authorized,or repair of products damaged by these modifications.
• incidental or consequential damages resulting from the product.(Some states do not
allow the exclusion of incidental or consequential damages,so the above exclusion may
not apply to you.This includes, but is not limited to, prerecorded material, whether
copyrighted or not copyrighted.)
• a product that is used for commercial or institutional purposes.
WHERE IS EXCHANGE AVAILABLE?
You may exchange the product in all countries where the product is officially distributed
by Philips.In countries where Philips does not distribute the product,the local Philips
service organization will attempt to provide a replacement product (although there may
be a delay if the appropriate product is not readily available).
Philips, P.O.Box 520890,Miami,
FL 33152, USA,
(402) 536-4171
BEFORE REQUESTING EXCHANGE...
Please check your owner's manual for assistance.If you have additional questions,call us
at 1-800-531-0039.
EXCHANGING A PRODUCT IN U.S.A.,
PUERTORICO,OR U.S.VIRGIN ISLANDS...
Contact 1-800-531-0039 to arrange an exchange. Or, ship the product, insured and
freight prepaid,and with proof of purchase enclosed, to the address listed below.
(In U.S.A.,Puerto Rico,and U.S.Virgin Islands, all implied warranties, including implied warranties of merchantability and fitness for a particular purpose,are limited in duration to
the duration of this express warranty.But, because some states do not allow limitations
on how long an implied warranty may last, this limitation may not apply to you.)
EXCHANGING A PRODUCT IN CANADA...
Please contact Philips at:
(In Canada,this warranty is given in lieu of all other warranties.No other warranties are
expressed or implied,including any implied warranties of merchantability or fitness for a
particular purpose. Philips is not liable under any circumstances for any direct,indirect,
special,incidental or consequential damages, howsoever incurred,even if notified of the
possibility of such damages.)
REMEMBER...
Please record below the model and serial numbers found on the product.Also,please fill
out and mail your warranty registration card promptly.It will be easier for us to notify
you if necessary.
Philips Exchange Program
Suite A
406 North Irish Street
Greeneville TN 37745
1-800-661-6162 (French Speaking)
1-800-531-0039 (English or Spanish Speaking)
MODEL # ____________________________________
SERIAL # ____________________________________
This warranty gives you specific legal rights.You may have other rights
which vary from state/province to state/pro
EL4967E007 / 8-02
vince
.
BELTCLIP CLIP CEINTURE CINTURÓN DE CIERRE
BELT CLIP
LIFT
LOCK
RELEASE
English
(supplied or optionally available)
1 To attach the belt clip to the CD player, position the shaped grip (found on the back of
the belt grip) so that it fits into the belt clip hole of the CD player. Turn the clip to
LOCK as indicated on the CD player.
2 To detach, gently lift the belt clip and turn to RELEASE as indicated on the CDplayer.
(fourni ou en option)
Français
1 Pour fixer le clip ceinture, placez l’attache (située sur le dos du clip) dans le trou prévu
à cet effet sur l’appareil. Tournez l’attache jusqu’à LOCK, comme indiqué sur l’appareil.
2 Pour enlever l’attache, soulevez-la doucement et tournez-la jusqu’à RELEASE.
Español
(suministrado o disponible de forma opcional)
1 Para ponerse el cinturón, encaje el broche (en la parte posterior del cinturón) en el orificio
del cinturón de cierre. Gire el cierre hasta LOCK tal y como se indica.
2 Para quitárselo, levante con cuidado el cinturón y gire hasta RELEASE tal y como se indica.
BELT CLIP
LIFT
LOCK
RELEASE
El aparato cumple las normas FCC, Parte 15 y 21 CFR 1040.10. Funcionamiento
dependiente de dos condiciones siguientes:
1. Este aparato no puede provocar interferencia dañina, y
2. Este aparato debe aceptar cualquier interferencia recibida, incluyendo las
interferencias que pueden provocar un funcionamiento insuficiente.
CAUTION
Use of controls or adjustments or performance of procedures other than
herein may result in hazardous radiation exposure or other unsafe
operation.
L’appareil répond aux normes FCC, Part15 et 21 CFR 1040.10. Fonctionnement
soumis aux deux conditions suivantes :
1. Cet appareil ne doit pas provoquer d’interférences nuisibles, et
2. Cet appareil doit accepter toute interférence reçue, y compris les
interférences susceptibles de provoquer un fonctionement peu satisfaisant.
The set complies with the FCC-Rules, Part 15 and with 21 CFR 1040.10.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
Canada
English: This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference Regulations
of the Canadian Department of Communications.
Français : Cet appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe B prescrites dans
le Règlement sur le Brouillage Radioélectrique édicté par le Ministère des
Communications du Canada.
ATTENTION
L’utilisation de commandes ou de réglages ou l’exécution de procédures
autres que celles décrites dans le présent manuel risque
d’entraîner une exposition à un rayonnement dangereux ou d’avoir d’autres
conséquences sur la sécurité.
PRECAUCIÓN
La utilización de controles o ajustes y la realización de procedimientos
distintos de los contenidos en este manual pueden provocar la
exposición a radiaciones peligrosas y a otros peligros.
English
BELT CLIP
LIFT
LOCK
RELEASE
CONTROLS / POWER SUPPLY
POWER SUPPLY / GENERAL INFORMATION
C
ONTROLS ( see figure 1 )
1 OPEN 2 ..............opens the CD lid
2 ∞ .......................skips and searches CD tracks backwards
3 § .......................skips and searches CD tracks forwards
4 2;......................switches the player on, starts or pauses CD play
5 9.........................stops CD play, clears a program or switches the player off
6 DBB.....................switches the bass enhancement on and off. This button also
switches acoustic feedback (the beep) on/off when it is
pressed for more than 2 seconds
7 ............................display
8 MODE.................selects the different playing possibilities: shuffle,
shuffle repeat all, repeat, repeat all and SCAN
9 PROGRAM..........programs tracks and reviews the program
0 RESUME.............stores the last position of a CD track played
HOLD...................locks all buttons
OFF......................switches RESUME and HOLD off
! LINEOUT/p........3.5 mm headphone jack and LINE OUT jack to connect the
player to another audio input of an additional appliance,
remote control (not on all versions)
@ VOL E ............adjusts the volume
# 4.5V DC...............jack for external power supply
$ ............................belt clip holder
% ............................type plate
Batteries (supplied or optionally available)
You can use the following batteries with this CD-player:
• normal batteries type LR6, UM3 or AA (preferably Philips), or
• alkaline batteries type LR6, UM3 or AA (preferably Philips).
Old and new or different types of batteries should not be combined.
Notes:–
– Remove batteries if they are empty or if the player is not going to be used for
a long time.
Inserting batteries
1 Push OPEN 2 to open the CD lid.
2 Open the battery compartment and insert either 2
normal or alkaline batteries.
Battery indication
The approximate power level of your batteries is shown
in the display.
Battery full
Battery two-thirds full
Battery one-third full
Battery dead or empty. When the batteries are dead or empty, the symbol
flashes, bAtt is displayed, and the beep tone sounds repeatedly.
Mains adapter (supplied or optionally available)
Use only the AY 3170 adapter (4.5 V / 300 mA direct
current, positive pole to the center pin). Any other product
may damage the player.
1 Make sure the local voltage corresponds to the power
adapter’s voltage.
2 Connect the power adapter to the 4.5V DC jack of the
player and to the wall outlet.
4
.
5
V
D
C
Note: Always disconnect the adapter when you are not using it.
Environmental information
• All redundant packing material has been omitted. We have done our utmost to
make the packaging easily separable into two materials: cardboard (box) and
polyethylene (bags, protective foam sheet).
• Your set consists of materials which can be recycled if disassembled by a
specialized company. Please observe the local regulations regarding the
disposal of packing materials, dead batteries and old equipment.
CD playerand CD handling
• Do not touch the lens A of the CD player.
• Do not expose the unit, batteries or CDs to humidity,
rain, sand or excessive heat (caused by heating
equipment or direct sunlight).
• You can clean the CD player with a soft, slightly
dampened, lint-free cloth. Do not use any cleaning
agents as they may have a corrosive effect.
• To clean the CD, wipe it in a straight line from the
center toward the edge using a soft, lint-free cloth. A cleaning agent may
damage the disc! Never write on a CD or attach a sticker to it.
• The lens may cloud over when the unit is moved suddenly from cold to warm
surroundings. Playing a CD is not possible then. Leave the CD player in a warm
environment until the moisture has evaporated.
• Active mobile phones in the vicinity of the CD player may cause malfunctions.
• Avoid dropping the unit as this may cause damage.
Headphones
• Connect the supplied headphones to the LINE OUT/p
jack of the player.
Note: LINEOUT/p can also be used for
connecting this set to your HiFi system.To adjust the
sound and volume, use the controls on the connected
audio equipment and on the CD player.
Average playing time of batteries under normal conditions
Battery type ESP on Power Save
Normal 5 hours 6 hours
Alkaline 16 hours 20 hours
Batteries contain chemical substances, so they should be disposed
of properly.
IMPORTANT!
Hearing safety: Do not play your headphones at a high volume. Hearing experts
advise that continuous use at high volume can permanently damage your hearing.
Traffic safety: Do not use headphones while driving a vehicle. It may create a
hazard and it is illegal in many countries. Even if your headphones are an open-air
type designed to let you hear outside sounds, do not turn up the volume so high
that you cannot hear what is going on around you.
GENERAL INFORMATION / CD PLAY
BELT CLIP
LIFT
LOCK
RELEASE
CD PLAY / FEATURES
In-car use (connections supplied or optionally available)
Only use the AY 3545 (4822 219 10033) or AY 3548 (3140 118 71890) carvoltage
converter (4.5 V DC, positive pole to the center pin) and the AY3501 cassette car
adapter. Any other product may damage the set.
1 Put the set on a horizontal, vibration-free and
stable surface. Make sure it is in a safe place,
where the set is neither a danger nor an
obstacle to the driver and the passengers.
2 Plug the voltage converter into the
cigarette lighter jack (only for 12 V car
battery, negative grounding), then connect
the wired end with 4.5V DC input jack on the
set.
3 If necessary, clean the cigarette lighter jack to obtain a good electrical con-
tact.
4 Turn down the volume and connect the cassette adapter plug to LINEOUT/p
on the set.
12 V DC
4,5 V DC
5 Carefully insert the cassette adapter into the car radio’s cassette compartment.
6 Make sure the cord does not hinder your driving.
7 Decrease the volume on the set if necessary. Start playbackon the set and
adjust the sound with the car radio controls.
• Always remove the voltage converter from the cigarette lighter jack-
when the set is not in use.
Note: If your car radio has a LINE IN jack, it is better to use it for the
car radio connection instead of the cassette.adapter. Connect the signal
lead to this LINE IN jack and to LINEOUT/p on the set.
Playing a CD
This CD-player can play all kinds of Audio Discs such
as CD-Recordables and CD-Rewritables. Do not try to
play a CD-ROM, CDi, VCD, DVD or computer CD.
1 Push the OPEN 2 slider to open the player.
2 Insert an audio CD, printed side up, by pressing the
CD onto the hub.
3 Close the player by pressing the lid down.
4 Press 2; to switch the player on and start playback.
yThe current track number and elapsed playing
time are displayed.
• You can pause playback by pressing 2;.
yThe time at which playback was paused starts
flashing.
• You can continue playback by pressing 2; again.
5 Press 9 to stop playback.
yThe total number of tracks and the total playing
time of the CD are displayed.
6 Press 9 again to switch the player off.
• To remove the CD, hold it by its edge and press the
hub gently while lifting the CD.
Note: If there is no activity, the set will automatically
switch off after a while to save energy.
0
Playback information
• If a CD-Recordable (CD-R) or a CD-Rewritable (CD-RW) is not recorded
properly,nF dISC is displayed, indicating that the CDhas not been
finalized. In that case, use FINALIZE on your CD recorder to complete the
recording.
• When playing a CD-Rewritable (CD-RW), please note that it takes 3–15
seconds after pressing 2; for sound reproduction to start.
• Playback will stop if you open the CD lid.
• While the CD is read, 1 -:- flashes in the display.
Volume and bass
Volume adjustment
• Adjust the volume by using VOL E.
Bass adjustment
• Press DBB to switch the bass enhancement on or
off
y is shown if the bass enhancement is
activated.
Remote control (supplied or optionally available)
Use the AY 3768 cord remote control.The buttons on the remote
control have the same functions as the corresponding buttons on the set.
1 Press 9 twice to switch off the set.
2 Firmly connect the remote control to LINE OUT/p on the set.
3 Adjust the volume VOL E on the CD player and remote control.
Selecting a track and searching
Selecting a track during playback
• Briefly press ∞ or § once or several times to skip to
the current, previous or next track.
yPlayback continues with the selected track, and
the track’s number is displayed.
Selecting a track when playback is stopped
1 Briefly press ∞ or § once or several times to select the desired track. The
track number is displayed.
2 Press 2; to start CD play.
yPlayback starts with the selected track.
Searching for a passage during playback
1 Keep ∞ or § pressed to find a particular passage in
a backward or forward direction.
ySearching starts while playback continues at low
volume. After 2 seconds the search speeds up.
2 Release the button when you reach the desired passage.
yPlayback continues from this position.
Notes: – If the player is in SCAN mode (see MODE chapter), searching is not
possible.
– In shuffle, shuffle repeat all or repeat mode (see MODEchapter), or
while playing a program, searching is only possible within the
particular track.
You can store up to 30 tracks to play in a program.
A single track may be stored more than once in the
program.
1 While playback is stopped, select a track with
2 Press PROGRAM to store the track.
3 Select and store all desired tracks in this way.
4 Press 2; to start playback of your selected tracks.
• You can review the program by pressing PROGRAM
Notes: – If you press PROGRAM and there is no track selected, SEL is
Clearing the program
• While playback is stopped, press 9 to clear program.
Note: The program will also be cleared if the power
It is possible to play tracks in random order, to repeat a
single track or the entire CD, and to play the first few
seconds of each track.
1 Press MODE during playback as often as required in
y SCAN: The first 10 seconds of each of the
2 Playback starts in the chosen mode after 2 seconds.
• To return to normal playback, press MODE repeatedly until the display shows
With a conventional portable CD-player you might have experienced that the
music stopped e.g. when you were jogging. The ELECTRONIC SKIP PROTECTION
prevents loss of sound caused by light vibrations and shocks. Continuous playback
is ensured. However ESP does not prevent playback interruptions during vigorous
running. It also does not protect the unit against any damage caused by dropping!
On this set ESP is default on. It is possible to set ESP off and enter the Power
Save mode. The Power Save mode helps to extend battery
lifetime for longer playback.
• Press MODE for more than 2 seconds.
• Press MODE again for more than 2 seconds.
FEATURES
Programming track numbers
You can store up to 30 tracks to play in a program.
A single track may be stored more than once in the
program.
1 While playback is stopped, select a track with
∞ or §.
2 Press PROGRAM to store the track.
yprogram lights up; the track number
programmed and P with the total number of
stored tracks are displayed.
3 Select and store all desired tracks in this way.
4 Press 2; to start playback of your selected tracks.
yprogram is shown and playback starts.
• You can review the program by pressing PROGRAM
for more than 2 seconds.
yThe display shows all the stored tracks in
sequence.
Notes: – If you press PROGRAM and there is no track selected, SEL is
displayed.
– If you try to store more than 30 tracks, FULL is displayed.
Clearing the program
• While playback is stopped, press 9 to clear program.
yCLR is displayed once, programgoes off,
and the program is cleared.
Note: The program will also be cleared if the power
supply is interrupted, or if the CD-player lid is
opened, or if the set switches off automatically.
FEATURES / TROUBLESHOOTING
RESUME and HOLD
You can interrupt playback and continue (even after an
extended period of time) from the position where
playback stopped (RESUME) and you can lock all buttons
of the set so that no action will be executed (HOLD).
Use the RESUME–HOLD–OFF slider for these functions.
RESUME – continuing from where you have stopped
1 Switch the slider to RESUME during playback to activate RESUME.
yresume is shown.
2 Press 9 whenever you want to stop playback.
3 Press 2; whenever you want to resume playback.
yresume is shown and playback continues
from where you have stopped.
• To deactivate RESUME, switch the slider to OFF.
yresume goes off.
HOLD – locking all buttons
You can lock the buttons of the set by switching the slider to HOLD. Now, when a
key is pressed, no action will be executed. This is of use, for example, when
transporting the player in a bag. With HOLD activated, you can avoid accidental
activation of other functions.
1 Switch the slider to HOLD to activate HOLD.
yAll buttons are locked. HoLd is shown when
you press any button. If the set is switched off,
hold will be shown only when 2; is pressed.
2 To deactivate HOLD, switch the slider to OFF.
Note: If you deactivate HOLD by switching the slider to RESUME,
you will be activating the RESUME function.
Troubleshooting
WARNING: Under no circumstances should you try to repair the set yourself as
this will invalidate the warranty. If a fault occurs, first check the points listed,
before taking the unit for repair. If you are unable to solve a problem by following
these hints, consult your dealer or service center.
The CD player has no power, or playback does not start
• Check that your batteries are not dead or empty, that they are inserted
correctly, that the contact pins are clean.
• Your adapter connection may be loose. Connect it securely.
• For in-car use, check that the car ignition is on. Also check player’s batteries.
The indication no diSC is displayed
• Check that the CD is clean and correctly inserted (label-side upward).
• If your lens has steamed up, wait a few minutes for this to clear.
The indication nF diSC is displayed
• CD-RW (CD-R) was not recorded properly. Use FINALIZEon your CD-recorder.
The indication
HOLD is on and/or there is no reaction to controls
• If HOLD is activated, then deactivate it.
• Electrostatic discharge. Disconnect power or remove batteries for a few seconds.
The CD skips tracks
• The CD is damaged or dirty. Replace or clean the CD.
• RESUME, SHUFFLE or PROGRAMis active. Switch off whichever is on.
No sound or bad sound quality.
• PAUSE might be active. Press 2;.
• Loose, wrong or dirty connections. Check and clean connections.
• Volume might not be appropriately adjusted. Adjust the volume.
• Strong magnetic fields. Check player’s position and connections. Also keep
away from active mobile phones.
• For in-car use, check that the cassette adapter is inserted correctly, that the car
cassette player’s playback direction is correct (press autoreverse to change),
and that the cigarette lighter jack is clean. Allow time for temperature change.
Selecting different playing possibilities−MODE
It is possible to play tracks in random order, to repeat a
single track or the entire CD, and to play the first few
seconds of each track.
1 Press MODE during playback as often as required in
order to activate one of the following ‘modes’. The
active mode is shown in the display.
yshuffle : All tracks of the CD are played in
random order until all of them have been played once.
yshuffle repeat all : All tracks of the CD
are played repeatedly in random order.
yrepeat : The current track is played repeatedly.
yrepeat all : The entire CD is played repeatedly.
y SCAN: The first 10 seconds of each of the
remaining tracks are played in sequence.
2 Playback starts in the chosen mode after 2 seconds.
• To return to normal playback, press MODE repeatedly until the display shows
no active modes.
ESP / Power Save Mode
With a conventional portable CD-player you might have experienced that the
music stopped e.g. when you were jogging. The ELECTRONIC SKIP PROTECTION
prevents loss of sound caused by light vibrations and shocks. Continuous playback
is ensured. However ESP does not prevent playback interruptions during vigorous
running. It also does not protect the unit against any damage caused by dropping!
On this set ESP is default on. It is possible to set ESP off and enter the Power
Save mode. The Power Save mode helps to extend battery
lifetime for longer playback.
• Press MODE for more than 2 seconds.
y disappears. power save modeis now activated.
• Press MODE again for more than 2 seconds.
y is displayed once
ESP on
➟ Power Save ➟ESP on
BELT CLIP
LIFT
LOCK
RELEASE
program
program
program
repeat all
shuffle
resume
hold
resume
3140 115 2968.1 Printed in China
CLASS 1
LASER PRODUCT
English
Français
Español
BELT CLIP
LIFT
LOCK
RELEASE
Meet Philips at the Internet
http://www.philipsusa.com
Read this manual first!
If you have any problems, do not attempt
to return this product to the store.
For fast help, call us first!
1-800-531-0039
S
E
E
W
H
Y
I
N
S
I
D
E
I
M
P
O
R
T
A
N
T
!
Return
your Warranty
Registration Card
within 10 days
Loading...