Philips AJ3600 User Manual
Clock Radio AJ 3600
User manual
REPEAT ALARM
BRIGHTNESS CONTROL
AJ3600
PRO
JECTION CLOCK RADIO
ALA
RM
RESET/SLEEP
RADIO
O
N/OFF
BAN
D
1
AL1 AL 2
P
RESET
O
N
O
FF
1
AL AL
VO
LUM
E
T
UN
IN
G
DC 7.5V
123
9
4
6
4
1
2
3
5
1
2
7
8
Clock radio
Meet Philips at the Internet
http://www.philips.com
Printed in China PDCC-JH-0730
Register your product and get support at
www.philips.com/welcome
3
P
N
O
I
T
C
E
J
O
R
P
E
S
R
E
V
2
E
R
R
O
J
E
C
T
I
O
N
O
N
/
O
F
F
3
1
R
N
O
O
T
I
A
T
T
C
E
E
P
J
R
O
1
M
R
A
L
A
T
E
5
9
S
1
+
R
5
U
O
H
8
S
E
T
A
L
A
E
T
S
-
1
E
5
R
P
S
R
M
2
2
M
I
N
U
3
T
E
+
4
E
E
M
I
T
T
4
6
7
English
SUPPLIED ACCESSORIES
– 1X certified AC/DC 7.5V adapter (Sunstrong Inter’l Ind. Ltd.,Model:VD075025F)
(Input: 110-127V/220-240V ~60/50Hz, Output: 7.5V 250mA)
TOP AND FRONT PANEL
(See 1)
1 RADIO ON/OFF
– switches the radio on/off; displays radio frequency
– switches off sleep timer
2 BAND –select FM/ MW waveband
3 ALARM RESET / SLEEP
– stops active alarm for 24 hours
– activates the radio for sleep function
–
displays/adjusts/switches off sleep timer
4
REPEAT
ALARM /
BRIGHTNESS CONTROL
– switches off the alarm for a 9 minute period
– changes the brightness of the display illumination
– stops SLEEP function
5 DISPLAY –shows clock/alarm times and status of the set
6 AL 1 (
AL ) –
switches on/off ALAM 1 radio mode
– displays
ALAM 1
time
7 AL 2 (AL) –switches on/off ALAM 2 buzzer mode
– displays
ALAM 2
time
8
Battery compartment – for 4 batteries, type R6, UM3, AA
9
RESET – press if the set / display does not react to operation of any button
BACK PANEL
(See 2)
1 TUNING +/-–tunes to radio stations
2 VOLUME
–
adjusts the sound level
3 DC 7.5V
–
socket for AC/DC 7.5V adapter
4
Pigtail – improves FM reception
LEFT & RIGHT PANEL (See
3)
1 Projection lens
2 REVERSE PROJECTION
–
turns time/hour digits upside down(AC-powered only)
3 PROJECTION ON/OFF
–
switches the projection on/off
4
ROTATE PROJECTION –
adjusts projection slightly to a different angle
5 SET ALARM 1 / PRESET 1
–
sets ALARM 1
time
– stores, recalls and shows station 1
6 SET ALARM 2 / PRESET 2 –sets ALARM 2
time
– stores, recalls and shows station 2
7 MINUTE + / PRESET 3 –adjusts the minutes for clock and alarm times
– stores, recalls and shows station 3
8 SET TIME / PRESET 4
– sets the clock time
– stores, recalls and shows station 4
9 HOUR + / PRESET 5
– adjusts the hours for the clock and alarm times
– stores, recalls and shows station 5
POWER SUPPLY
Batteries (not included)
1
Open battery door and insert four batteries (preferably PHILIPS POWER LIFE
or alkaline), type R6, UM3 or AA as indicated in the compartment.
2
Remove the batteries from the set if they are exhausted or not be used for a
long time.
•
When you replace batteries, the preset stations, alarm and clock time settings can be stored for up to 3 minutes. (see 'Self-Powered Back-Up').
Batteries contain chemical substances, so they should be disposed of
properly.
Batteries (battery pack or battery installed) shall not exposed to excessive heat such as sunshine, fire or the like.
Mains adapter
1
Connect the mains adapter to the set's DC 7.5V socket and to the power
socket.
™
indicates the set is now adapter operated.
•
Make sure your adapter is properly connected to save battery energy!
2
Always disconnect the mains adapter if you are not using the set.
™
indicator goes out.
Helpful hints: To avoid damage to the set, use only the adapter supplied!
The type plate is located on the bottom of the set inside the battery
compartment.
SELF-POWERED BACK-UP
The self-powered back-up conveniently allows your preset stations, alarm and clock
time settings to be stored for up to 3 minutes when there is a power interruption
e.g. AC power failure or when changing batteries.The complete clock radio and backlight illumination will be switched off.
If power supply returns after 3 minutes and the display shows:
• clock time blinking - indicates you need to re-adjust the clock time.
BATTERY LOW MODE
indicates batteries low. Replace with fresh batteries to ensure all the features
on your set will function properly.
BASIC FEATURES
Reset
Should your set receive external interference e.g. static electricity from carpets, thunderstorms, etc. RESET allows you to clear all previous settings and start up again.
•Use a ballpoint pen to press the RESET hole found on the bottom of the set.
Illumination brightness
Press REPEAT
ALARM /
BRIGHTNESS CONTROL once or more.
•
The brightness of the display can be adjusted:
Bright
➟ Medium ➟ Low ➟ Bright (when AC-powered)
Low
➟ Bright ➟ Low ➟ Bright (when battery-powered)
4
5
RADIO FM
AL
ON
PRESET
6
SLEEP RADIO MW
AL
ON
PRESET
2
AL
5
OFF
AL
ON
AL
ON
7
P
N
R
O
O
I
T
J
E
C
T
I
O
1
.
8
x
N
a
0
M
O
N
/
O
F
F
N
O
I
T
C
E
J
O
R
P
E
T
A
T
O
R
AL
C
E
J
O
R
P
E
S
R
E
V
E
R
ON
Loading...