How it Works
Philips
Loading...
AEH2110
User Manual
34 pgs2.4 Mb0

Philips AEH2900, AEH23, AEH2110, AEH2120, AEH2130 User Manual

Download
User manual
(AEH2900, AEH2110, AEH2120, AEH2130, AEH2310)
1EN
Contents
1 Important safety instructions 3
Safety 3
Compliance 4
Care of the environment 5
Notice 5
2 Overview 7
Motion sensor 7
Door and window sensor 7
Temperature and humidity sensor 8
Intelligent switch 9
Status indicator 9
3 Setup 11
Join your Smart Home network 11
Reset 15
4 Place 18
2 EN
Place the Motion sensor 18
Place the Door and window sensor 20
5 Use 23
Philips Smart Home app 23
Manage devices 24
Set the rules of home automation 26
Access the devices remotely 28
6 Check for updates 29
7 Technical data 30
Sensors (for indoor use only) 30
Intelligent switch 30
3EN
1 Important safety instructions
Safety
CAUTION: For INDOOR USE ONLY!
DO NOT use this Intelligent switch with non-resistive loads, such as motors,
compact uorescent light (CFL) bulbs or uorescent lighting.To reduce the risk of electric shock, this Intelligent switch has a third (grounding) pin. As a grounding type plug, this Intelligent switch only ts into a grounding type power outlet. Make
sure that you use this Intelligent switch with a grounding type power outlet that
has been properly installed by a qualied electrician.
Important Safety Instructions
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Clean only with dry cloth.
f The batteries shall not be exposed to excessive heat such as sunshine, re
or the like.
• Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/ hazardouswaste/perchlorate.
g This product shall not be exposed to dripping or splashing.
4 EN
Compliance
Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Notice for the USA
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Relocate the receiving antenna.
• Increase the separation between equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. The set complies with the FCC-Rules, Part-15. Operation is subject to the
following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that
may cause undesired operation.
Notice for Canada
CAN ICES-3(B)/NMB-3(B) This device complies with Industry Canada license-exempt RSS standard(s): Operation is subject to the following Two conditions:(1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
5EN
Care of the environment
Environmental information
All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused if
disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, and old equipment.
Disposal of your old product and battery
Your product is designed and manufactured with high quality materials and
components, which can be recycled and reused. This product may contain lead and mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or visit www.recycle.philips.com.
This product contains batteries:
• Dispose of batteries properly. Do not incinerate. Batteries may explode if
overheated.
• Do not wrap in metal or aluminum foil. Wrap in newspaper before discarding.
• It is suggested that you contact your local town or city to determine proper
battery redemption site(s) in your area.
• Please visit www.call2recycle.org for additional information on a recycling center in your area for rechargeable batteries.
Notice
Disclaimer
• Your use of Philips Smart Home is at your sole risk. Gibson Innovations and its subsidiary companies (individually and collectively “Gibson Innovations”)
are not responsible for the operation of such Philips Smart Home or your
use thereof and Gibson Innovations shall have no liability to you related thereto.
6 EN
• The sensors and/or Intelligent switch are intended as an aid. They are not
substitutes for home security supervision and should not be used as such.
Written Offer
Gibson Innovations hereby offers to deliver, upon request, a copy of the complete
corresponding source code for the copyrighted open source software packages
used in this product for which such offer is requested by the respective licenses. This offer is valid up to three years after product purchase. To obtain source code, please contact open.source@philips.com. If you prefer not to use email or if you do not receive conrmation receipt within a week after mailing to this email address, please write to Open Source Team, Gibson Innovations Limited, 5/F, Philips
Electronics Building, 5 Science Park East Avenue, Hong Kong Science Park, Shatin,
New Territories, Hong Kong. If you do not receive timely conrmation of your letter, please email to the email address above.
Specications are subject to change without notice. Philips and the Philips’ Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used by under license from Koninklijke Philips N.V.. Gibson Innovations reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly.
7EN
2 Overview
With the Smart Home devices and Philips Smart Home app, you can have the changes at your home monitored, and set rules to have the connected home
appliance powered on or off automatically according to the changes.
Motion sensor
The Motion sensor detects the movement of people at home.
a Status indicator
b Detection lens
Door and window sensor
The Door and window sensor detects the opening/closing of door or window at home.
a
b
AEH2110
8 EN
a Status indicator
b Alignment mark
Temperature and humidity sensor
The Temperature and humidity sensor detects the temperature and humidity at
home.
a Status indicator
a b
AEH2120
a
AEH2130
9EN
Intelligent switch
The Intelligent switch powers on or off the connected appliance at home.
a Power on/off
b Power indicator
c Status indicator
d Setup button
Status indicator
Indicator Status of the device Start-up
From amber to red Ready for pairing (for a device that has never
been paired with the Bridge, or a device that has been restored to factory settings)
Flashing amber Ready for re-joining (for a device that has
been paired with the Bridge before)
Operation
d
b
a
c
AEH2310
10 EN
Solid green for less than one second
An event that triggers notications happens.
Flashing red Disconnected Flashing red and green
alternately
Firmware updating underway
Low battery
Solid red for three sec-
onds, and then, ashing red
Battery to be replaced
11EN
3 Setup
Join your Smart Home network
1 On your mobile device, download and install the Philips Smart Home app.
2 Follow the onscreen instructions to get connected to the Bridge. 3 Follow the onscreen instructions to add your Smart Home devices to the
Bridge. For setup, bring the Smart Home device as close to the Bridge as possible.
a Install the batteries. Push to close the battery door. On the Intelligent
switch, press the power button to switch on.
b Don't release the battery door until the status indicator turns from
amber to red.On the Intelligent switch, press and hold the setup button until the status indicator turns from amber to red.
c On the Philips Smart Home app, press the Search button.
» When the status indicator lights up in green, pairing starts.
iOS
Philips Smart Home
Smart Home
Smart Home
Get started
Demo
+
12 EN
Note
• The device exits the pairing mode after three minutes. To re-enter the pairing mode, open the
battery door and close it as described in Step 3.
Install or replace batteries
To install or replace batteries on your Smart Home devices, do the following:
1
2
Search
All devices
No device has connected
Add devices
Home
Settings
Rules
2
3
13EN
Motion sensor
Door and window sensor
Temperature and humidity sensor
1
2
3
1
2
3
1
2
3
14 EN
Plug the Intelligent switch
To add the Intelligent switch to the Bridge, do the following:
1 Insert the Intelligent switch into a power outlet properly.
2 Press and hold the Setup button until the status indicator turns from amber
to red.
15EN
Reset
Reset network connection
Reset the network connection when:
• a device re-joins the Smart Home network after the batteries are replaced.
• there are connection problems with the Smart Home network.
Indicator Status of the device
ashing red Network connection lost
On the sensor, do the following:
1 Open the battery door. 2 Push to close the battery door. Release the door when the status indicator
ashes in amber.
3 With the Philips Smart Home app, add the device to the Bridge (see 'Join
your Smart Home network' on page 11).
On the Intelligent switch, do the following:
1 Press and hold the Setup button until the status indicator ashes in amber.
16 EN
2 With the Philips Smart Home app, add the device to the Bridge (see 'Join
your Smart Home network' on page 11).
Restore factory settings
Restore factory settings when:
• you want to connect your device to another Bridge.
On the sensor, do the following:
1 Delete the device from the Bridge (see 'Delete the device' on page 25). 2 Open the battery door. 3 Push to close the battery door. Don't release the door until the status
indicator turns from amber to red.
4 With the Philips Smart Home app, add the device to the Bridge (see 'Join
your Smart Home network' on page 11).
On the Intelligent switch, do the following:
1 Delete the device from the Bridge (see 'Delete the device' on page 25). 2 Press and hold the Setup button until the status indicator turns from amber
to red.
3 With the Philips Smart Home app, add the device to the Bridge (see 'Join
your Smart Home network' on page 11).
17EN
Tip
• If you press and hold the setup button for more than six seconds, the status indicator turns off. To
restore factory settings, re-do Step 1.
18 EN
4 Place
• Use the Smart Home devices in an indoor environment.
• Keep such devices from exposure to moisture, direct sunlight, or excessive
heat.
• To ensure good connection, check the distance and obstacles, such as walls,
between the Bridge and devices.
Place the Motion sensor
Find a right location
• Select a location where a person is expected to cross the range of detection.
• To avoid false detection events, select a location where the height and angle
are right to keep non-people objects out of detection, such as pets.
• Avoid locations that are exposed to sources of heat, such as a heater or radiator, or sources of strong air drafts, such as fans or air conditioners.
Use the mounting kit
With the supplied mounting kit for motion sensor, you can adjust the angle of view through the ball joint.
To use the supplied mounting kit, do the following:
19EN
• In Step 2, use the screw holder for a concrete wall or surface. For a wooden
surface, you can the screw only.
Use the adhesive tape
You can also use the adhesive tape mount the sensor as needed.
1
3
4
a
b
2
5mm
>30mm
20 EN
Place the Door and window sensor
• Avoid the exposure to moisture and direct sunlight.
• Use the alignment marks to align the two components.
• Mount the two components securely just in case any one of them may drop
during movement.
2
1
3
21EN
1
22 EN
2
23EN
5 Use
Philips Smart Home app
Through the Philips Smart Home app you can set up the Smart Home devices, set rules of home automation, and continue to monitor changes and control the
devices on a mobile device while you are away from home.
a Go to the Home screen.
b Find connected devices by type or location.
c Display connected devices in a view of grid or list.
d Set the device.
e Add a device.
f Go to the settings menu.
g Set or edit the rules of home automation.
a
b
c
d
e
f
g
24 EN
Manage devices
Set the device
You can edit the device information by attaching a photo and naming the location.
• On the Home screen, tap the device to edit the device information.
• For the Motion sensor, select the sensitivity level as needed.
• You can select the unit of measurement for the Temperature and humidity
sensor, Fahrenheit degree or Celsius degree. From the Home screen, tap > Unit.
Check device status
Go to the Home screen to check the status of devices. The list of events is displayed at the top.
25EN
Delete the device
Delete the device when:
• you want to remove the device from the Bridge.
• you want to restore the factory settings of the device. (see 'Restore
factory settings' on page 16)
1 From the Home Screen, select the device. 2 Tap the option to delete the device.
26 EN
Set the rules of home automation
To set a rule of home automation, set an event or time/ location as trigger. Then, set an action that is associated with the trigger.
Set the trigger
1 From the Home screen, go to . Tap to create a rule. 2 Tap a icon to set a trigger.
• A trigger can be an event detected by your Smart Home device, or
time or location detected by your mobile device.
• To set a location as trigger, you can also go to from the Home screen
and select Geofencing.
Set the action
• Tap a icon to set an action. An action can be power on/ off of the home appliance that has been plugged into the Intelligent switch, or the push notication that you receive on your mobile device when the event happens, or on/ off of the connected light bulbs according to the scene that you have set.
27EN
Edit the rules
• From the Home screen, tap . Select a rule to edit or delete it.
28 EN
Access the devices remotely
To access your Smart Home devices remotely, log in to the portal. The rst time you log in to the portal, create your account.
29EN
6 Check for updates
For updates of your Smart Home devices and the Philips Smart Home app, you
can receive messages on your mobile device. Follow the onscreen instructions to complete the updating.
30 EN
7 Technical data
Sensors (for indoor use only)
Power
• Two AAA alkaline batteries
Connectivity
• Zigbee
Motion sensor
Detection method
• Passive Infra red
Door and window sensor
Operating temperature & humidity
• 32°F to 104°F (0°C to 40°C), 10% to 90%
Temperature and humidity sensor
Operating temperature & humidity
• Temperature: 32°F to 104°F (0°C to 40°C)
• Humidity: 10% to 95%
Intelligent switch
Grounding type power plug (for indoor use only)
• Model: AEH2310/37 Output: AC 120 V~ 60 Hz, 15 A, 1800 W (for use with resistive load only)
Connectivity
Zigbee
31EN
2015 © Gibson Innovations Limited. All rights reserved. This product has been manufactured by, and is sold under the responsibility of Gibson Innovations Ltd., and Gibson Innovations Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license from Koninklijke Philips N.V.
AEH2900_37_UM_V1.0
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use