Philips ADD4969, ADD4966 User Manual
Dispenser
ADD4966
ADD4969
User Manual 1-9
Petunjuk Penggunaan 10-18
Content
Main technical specication
1 1
2 2
Product overview
3 3
Indicator panel and switch
4 4
Instruction
·Filter
·UV-LED light
5 6
Precautions
6 7
Cleaning and maintenance
7
Trouble shooting
8
Guarantee and Service
9
Packing list
5
5
8
9
9
1 Main technical specication
制冷开关
制热开关
Model
Filter model
Rated voltage
Rated frequency
Heating power
Cooling power
Hot water
Cold water
Environmental temp.
Coolant
ADD4966 ADD4969
ADD502
220V
50Hz
170/350W
85W
≥90℃, 3.8L/h with high power,
1.8L/h with low power
≤10℃，2L/h
T
R134a, 38g
Relative humidity
Protection of anti-electric shock
≤90%
I
1
2 Product overview
1
12
2
3
5
6
7
Child Safety Lock
1
2
Indicator panel
3
Cold Water Faucet
Ambient Water Faucet
4
Hot Water Faucet
5
4
8
9
10
11
9
Water Bottle Cap with Hose
Filter
10
Water Bottle
11
12
Power Switch
13
Condenser
13
14
15
16
6
Drip Tray
7
Lower Cabinet Door
8
Filter Reset Button
2
14
Power Cord
15
Dispenser Flushing Drain
16
Filter Drain
3 Indicator panel and switch
Filter lifetime indicator
Cooling indicatorHeating indicator
Water shortage indicator
Indicator panel
When the dispenser is heating up the water in the hot water tank, the heating indicator light
will be on.
When the dispenser is cooling the water in the cold water tank, the cooling indicator light will
be on.
When there's no water left in the bottle, the water shortage indicator will be on. Replace with
a new bottled water and the indicator will switch o automatically.
The lter lifetime indicator red light will start to ash when there are 15 days lter lifetime left,
it will stay on until the lter reaches the end of life. Replace the lter and reset the lifetime
indicator as instructed, the indicator will switch o automatically afterwards.
Cooling switch
Low power heating
O
High power heating
Power Swi tch
At the back of the dispenser there is a black switch which controls the heating power. You
may press it to switch between high power, low power and OFF.
3
Every time when you plug in the water dispenser again, it will need some time for getting
hot and cold water.
Turn the black heating switch to ‘I’, please wait for around 30 minutes for hot water;
Turn the black heating switch to ‘II’, please wait for around 15 minutes for hot water;
Turn the green cooling switch to ‘ON’, please wait for around an hour for cold water.
4 Instruction
(1) Unpacking the water dispenser
· Cut and remove the straps from the box. DO NOT turn the box upside down, or lay it on its
side. The bottom of the box is separate from the top section. Lift straight up on the top box
section to remove the top box section. Remove the Styrofoam packaging and plastic bag.
Lift the water dispenser o the bottom of the bottom of the box. Wipe it clean if necessary.
· Place the machine on a hard, at surface. Make certain the unit is leveled. The unit should
not be placed near direct sunlight or other source of heat.
· It is best to place the water dispenser in an area with good air circulation. Make sure there is
at least 4 inches (10cm) of space between the back of your water dispenser and the wall.
Keep a minimum distance of 2 inches (5cm) on each side of your water dispenser.
Warning: the drain plug on the back of the unit may become loose during shipping. Fasten
the drain plug tightly before you start to operate the unit. If the drain plug is loose, the unit
may leak and cause oor damage.
(2) Settling water bottle
· Make sure the water dispenser is not plugged into an electrical outlet.
· Open the door of the lower cabinet.
· Place full water bottle on oor. Remove the plastic cover over the mouth of the water bottle.
· Place the stainless tube inside the bottle and place the water bottle cap rmly over the
mouth of the water bottle.
· Attach the hose to the top of the cap using the quick connect system shown below*.
· Slide the bottle inside the cabinet and close the lower cabinet door.
* Your new water dispenser features an adjustable quick connect system. For proper
operation, make sure the connector is sealed tight (Fig. 1);
The connector can be removed easily for cleaning with warm soapy water (Fig. 2);
The stainless steel tube can be adjusted up and down to accommodate both 3 gallon and 5
gallon water bottle (Fig. 3).
4
Note: If there is not a secure connection between the hose cap and the connector on the
water dispenser, the water pump will operate but the water dispenser will not dispense water.
Make sure the hose is connected to the water dispenser correctly.
(3) Dispense water
· Plug the water dispenser into a grounded power outlet. The unit will pump the water from
the water bottle into the cooling and heating tanks.
· Press the hot water faucet until water ows out.
· Turn on the power switch on the back of the unit. The cooling or heating feature will start
running. The indicator light will be on when heating or cooling function is working. Do not
touch both switches during the time.
· Enjoy the hot or cold water you need.
· If you are not going to use hot water, turn the black heating switch to ‘O’; if you are not going
to use cold water, turn the green cooling switch to “OFF” to conserve energy.
Note: please wait until the water pump stops running before using the unit. If the water tank is
not full, no water will dispense from the water faucet.
Filter
(1) Function of the lter
The lter is made of carbon block, which can remove particles such as micro-plastics, as well
as improving the taste and texture of water.
5
(2) Flushing the lter for rst time usage
· Unplug the lter drain at the back of the dispenser, and
connect the lter drain with the PE pipe provided. Put
the other end of the PE pipe in a container or a bucket
which can hold at least 5L water.
· Plug the water dispenser into a grounded power outlet. Insert the stainless steel pipe into the
bottle, and slide the bottle in. Close the cabinet door. Water that is used to ush the lter will
ow into the container automatically from the lter drain. Flush the lter for 3 minutes.
· Once it's done, open the cabinet door, remove the PE pipe from the lter drain and plug the
lter drain.
· Close the cabinet door. Now the lter is ready to use.
(3) Replacing the lter and resetting lter lifetime indicator
· Open the cabinet door and remove stainless steel pipe
from the bottle. Press the cold water button to empty
the water tank inside.
· Turn the lter counterclockwise to take o the old lter.
· Screw the new lter clockwise into the lter holder until
the dots on the lter and the holder is fully aligned.
· Press and hold the reset button for 5 seconds to reset
the lter lifetime indicator. Once successful, the lter lifetime indicator on the panel will
sw itch o .
· Flush the lter as instructed above.
· If you reset the lifetime by mistake, continuously short press the reset button for 5 times
within 5 minutes, then the lter lifetime indicator will ash for 3 times which means you
revoke the reset successfully.
Dispenser ushing drain
Filter drain
Filter reset button
Filter
UV-LED light (applicable for ADD4969)
The UV-LED light is installed in the cold water tank to kill the bacteria which may grow inside.
It's controlled automatically by the software program once the dispenser is connected
with power.
5 Precautions
Warning
When using electrical appliances, basic safety precautions should be followed to reduce the
risk of re, electric shock, and injury to persons or property. Read all instructions before using
any appliance.
6
Loading...