Philips 9125 User Manual
User’s Manual for
Cordless Telephone with
Caller ID/Call W aiting 9125
Please read Part 1 — Important Product
Information, included in your package.
Lucent 9125 cover.L1 4/8/98, 11:31 AM3
Part 2
© 1998 Philips Consumer Communications L.P. All rights reserved.
Printed in China. 848116232 Issue L1
Lucent 9125 cover.L1 4/8/98, 11:30 AM2
CONTENTS
INSTALLATION................................. 3
Table/Desk Installation.......................... 3
Wall Installation..................................... 4
Belt Clip ................................................ 5
TELEPHONE OPERATION................. 6
Making a Call......................................... 8
Answering a Call ................................... 8
Ending a Call ......................................... 8
Redial .................................................... 8
Hold ...................................................... 8
Mute ...................................................... 8
Handset Ringer Selection ...................... 9
Handset V olume .................................... 9
Ringer Mute........................................... 9
Tempor ary Tone .................................... 9
Special T elephone Services .................10
Page/Handset Locator ......................... 10
Headset Jack........................................ 10
OPERATING RANGE........................11
TELEPHONE MEMORY ....................12
Storing Memory Numbers ...................12
Replacing Stored Memory Numbers ... 12
Deleting Stored Numbers.................... 12
Storing a Pause in a
Memory Number .............................12
Dialing Memory Numbers ...................12
Memory Guard .................................... 12
Caller ID Operation.......................13
About Caller Identification.................. 13
Display Screen Messages..................... 13
Reviewing Call History........................ 14
Removing a Call from Call History ......14
Removing All Calls from Call History .. 14
Dialing a Number in Call History ........ 14
BATTERIES.................................... 15
Charging the Handset Battery Pack.....15
Power Reserve .................................... 15
Charging the Spare Battery Pack......... 16
Replacing the Handset Battery Pack ...16
IN CASE OF DIFFICULTY .................17
Lucent 9125 book.L1 4/8/98, 4:14 PM1
1
2
Lucent 9125 book.L1 4/8/98, 11:24 AM2
INSTALLATION
Standard
Electrical
Outlet
Power Cord
Telephone
Line Jack
Telephone Line Cord
Modular
Telephone
Jack
T able/Desk Installation
1 Choose a spot near an electrical outlet and a telephone jack.
This phone requires a modular telephone jack and a standard electrical
outlet (110v AC). The outlet should not be controlled by a wall switch.
2 Install the handset battery.
(For an illustration of battery installation, see BATTERIES in this manual.)
• Remove the battery cover by pressing on the indentation and
sliding downward.
• Install the battery pack so that the metal contacts on the bottom
of the battery are aligned with the charging contacts in the
battery compartment.
• Replace the battery cover by sliding it on its track up over the
battery compartment until it snaps firmly in place.
3 Set the dial mode.
If you have touch tone service, set the switch on the bottom of the
base to TONE. If you have dial pulse (rotary) service, set the switch
to PULSE. Even if you have dial pulse service, you can still use
telephone services requiring tone signals. See “Temporary Tone” in
the OPERATION section of this manual.
Lucent 9125 book.L1 4/8/98, 11:24 AM3
3
INSTALLATION
4 Connect the telephone line cord.
Plug one end of the telephone line cord into the jack on the back of
the base. Plug the other end of the line cord into a modular jack.
Make sure the plugs snap firmly in place.
5 Connect the power cord.
Plug the power adapter into the jack labeled 11V DC on the back of
the base. Plug the AC adapter on the power cord into an electrical
outlet not controlled by a wall switch. The POWER light on the base
goes on.
6 Charge the handset batteries for 16 hours.
Place the handset face down or face up in the base. The CHARGING
light on the base goes on to show the handset is in the right position
to charge the batteries.
7 Check for dial tone.
After the batteries are charged, pick up the handset and extend the
base antenna. Check for a dial tone by pressing P, you should
hear a dial tone.
Wall Installation
1 Follow Steps 1–3 under Table/Desk Installation.
2 Turn the base unit over, and attach the wall mounting base to
the lower half of the base unit. Gently press down until it snaps
firmly into place.
4
Lucent 9125 book.L1 4/8/98, 11:25 AM4
Loading...