Philips 7P6051C User Manual

IVIAGNAVOX

Set-Up and Quick Use Guide

Table of Contents

and Remote Control

0 Antenna or

Cable TV

Am (i;nn \) A & B i\i>iirs

our TV has two sepa

rate ANT(enna)/Cable

y

inputs on the rear of the
set. These two signal
inputs offer convenient
hook-up options for both
normal TV program view
ing and Picture-In-Picture
(PIP) features.

The ANT(enna) A input is
intended for use and view
ing on the TV’s main
screen. Your home’s pri
mary Antenna, or Cable
TV signal, should be con

nected to this input for
normal TV setup, use and

feature operation.

The ANT(enna) B input is
a second, or auxiliary sig
nal source, designed to

supply your TV’s Picture­In-Picture (PIP) feature.
For many homes the use oJ\
a single existing Antenna
(or Cable TV) source, for
both ANT A and B, will be
the preferred method of

connection. This type of
connection (optional
Signal Splitter required)
will work properly for the
TV’s Main on-screen fea
tures, as well as retain all
the features designed for

PIP. For more details refer
to the Picture-In-Picture
section in your other
owner’s manual.

I—

A typical ANT(enna)
A and B connection (using a
common signal source and an
optional Signal Splitter):
If your Antenna or Cable TV
signal has a round cable con
nector (75 ohm) on the end,
then you're ready to connect it
to the 75ohm Signal Splitter.

If your antenna has flat twin­lead wire (300 ohm), you first
need to attach the antenna wires

to the screws on a 300 to 75
ohm adapter before connecting
to the 75ohm Signal Splitter.

300 to 75Q Adapter

(483521827003)

Round Cable

750 Ohm

Cable TV Signal

Gettine Started

Waming/Precautions

Hooking Up Your TV
How to Use the First Time Set-Up Control
Basic TV and Remote Control Operation
How to Use the On-Screen Menu Controls

<l>

Connect your Antenna or
Cable TV signal to the single
75 ohm input plug on the two­way Signal Splitter (optional).

Then connect two lengths of RF
Coaxial Cable to the two Output
plugs on the two-way Signal
Splitter (F-type connector on

both ends).

Combination VHF/UHF Antenna

- Outdoor or Indoor Antenna -

receives normal broadcast channels

2-13 (VHP) and 14-69 (UHF).

OPTIONAL TWO-WAY

SIGNAL SPLITTER
(single 75ohm Input to twin
75 ohm Outputs - optional
RF Coaxial connecting
cables also required)

Cable TV Company

...............................

.............................

For details on product registration, warranty,
and service refer to the other literature included
with your TV information packet.

Please retain all these materials and keep them
handy for future reference.

WARNING: TO PREVENT HRE OR SHOCK
HAZARD DO NOT EXPOSE THIS UNIT TO

.............

...............

.............

1
1

2

3.
4

RAIN OR EXCESSIVE MOISTURE.

<l>

Connect the twin Output
plugs on the Signal Splitter to
the ANT A and ANT B inputs
on the rear of the TV. Push the
round connector end of the RF
Coaxial Cable onto the
ANT(enna) plug and screw it
down tight (if using threaded
cables).

Back of TV

v.w.vAV.v.mmv.mvv.v.v.v.mv.w.vsm

Note: Proper operation of your TV is not dependent upon
connection of the ANT B input Its main purpose is to provide
an easily connected, dedicated picture source for PIP feature
use. Other signal source options (such as a satellite dish sys
tem, additional external antenna, VCÌR, or Video Game) could
also be connected and displayed on the TV screen through the
use of the ANT B input

Note: Although the ANT B input can be used and swapped

as the source for the TV’s Main picture, certain senip fea
tures (such as Smart Ciock) are only based on a signal being
detected at the ANTA input To ensure that all features are
operating properly, you may not want to rely solely on the ANT
B input as your TV’s Main screen signal source.

Remember, _
be sure to set the
TV for the type sig
nal you've connect
ed (see "SETUP"
on page 2 of this
Guide.)

Your TV can set

itself to select only
the channel numbers
on your Cable sys
tem (see “Setup"

page 2). If you use a
Cable Converter box,
set the TV to the

same channel as the
converter's CH 3/4
switch (on the rear of
the converter.)

To order any
optional accessory
contact your dealer
or call the toll-free
accessory ordering
number (1-800-292-

6066):

• Two Way Splitter

(M61000)

• 300-75 ohm

Adapter
(M61020)

• UHF/VHF

Antenna
Combiner
(SBV111133A01)

~ Cable Box

C viu.i: CoNVi;uri:u Boxics

or homes with Cable

TV Converter

F

Descrambler Boxes (with

PremiumIMovie Channels

scrambled), follow the
steps to the right for an
alternative ANT A and
ANTB PIP feature

hookup. Note the Cable TV\
signal will be split before

connection to the

Converter box (an option
al two-way 75 ohm Signal
Splitter will be required).

The signal routed to the TV’s ANT A input will allow for
Premium/Movie channels to be viewable on the TV.
Channel selection will be at the Converter.
The ANT A input chaimel on the TV should be set to the same
output channel as the Converter box (usually CH3 or 4).

Cable TV (Company

OPTIONAL TWO-WAY

SIGNAL SPLITTER

(JSE^UU

Connect your Cable
TV signal to the single 75 ohm
INPUT plug on a two-way
Signal Splitter (optional).

Cable TV Converter

Box Connection

<l>,

Connect one end of RF
Coaxial Cable to each of the
OUTPUT plugs on the 75 ohm
Signal Splitter. The two lengths
of RF Coaxial Cable need F­type connectors (screw-on or

push type) for both ends.

1 - EL6239 E001

Connect to ANT A Input Connect to ANT В Input

The signal routed to the TV’s ANT B input will allow for
the selection and viewing of Cable channels at the TV
(except for the scrambled Premium/Movie channels).

Ф

Connect one of the Signal
Splitter OUTPUTS to the
INput terminal on the Cable

TV Converter Box. Then route

Ф

Connect the remaining
Signal Splitter OUTPUT
from the Splitter to the ANT
B Input on the rear of the TV.

another connection from the

Cable Converter OUTput ter
minal to the ANT A Input on
the rear of the TV.

^1^

How то Use First Time Setup

Л11ГОМАГ1С Si; i l INCS

"rpirst Time Setup automati-

JL cally takes care of some

basic TV control settings for

you. Follow the steps in this

section to quickly add area
channel numbers into the
TV's memory, and set the TV

for your connected signal

(Antenna or Cable.) You can
also set the TV's Smart Clock

feature as well.

Press the MENU (M)

button on the remote or TV.
An on-screen list of TV fea
tures shows on the screen -

"MAIN MENU".

<l>c

Select "1ST TIME
SETUP" on the TV's Main
Menu. (Selected MENU item
is highlighted in RED.)

Press the remote's Menu^
buttons to move UP/DOWN
and from SIDE-TO-SIDE
within the list of on-screen
features.

Press ADV(ance) ▲ ▼ and
(+) (-) on the TV to move
UP/DOWN and from SIDE­TO-SIDE within the list of
on-screen features.

Many of the current TV
control settings will be
modified by continuing

with RrsMime Setup.

Press STATUS to Quit

Press "M" to Continue

or

<S>i

Press MENU (M) but
ton on the remote or TV to
begin SETUP.

Follow the instructions
shown on the TV screen to
guide you through the First
Time Setup and use of your
new TV.

-------------------------------

Press "AT” to select the

language you would like

the TV displays to use.

-► 1 ENGLISH 1

espaOol

FRANÇAIS

Press ’M“ to Continue

This TV is equipped with

the SMART CLOCK feature.

This feature is designed

to operate only on the
main antenna. ANT A.

Press "M" to Continue

Please check that your

other antenna or cable is

connected to the plug

marked ANT B on

the TV rear input panel.

Press STATUS to Quit

Press "M" to Continue

or

* Please Wait *

System is testing for

correct tuning mode

for ANT B.

1

* Please Wait *

^ System is testing for

correct tuning mode

for ANT A.

* Please Wait *

System is searching for

all active channels

on ANT B.

Testing channel 2

in cable mode.

* Please Wait *

System is searching for

^ all active channels

1

on ANT A.

Testing channel 2

in cable mode.

The search for active
channels is complete

for ANT B.

17 channels were found

and saved in memory

Press “M" to Continue

The search for active
channels Is complete

fnrAMTA

17 channels were found

and saved in memory

Press ’M" to Continue

This TV contains a clock

which can automatically

be set through the

aviART CLOCK feature.

The clock will be set
to the time broadcast

by certain TV stations.

Press 'M' to Continue

This TV is equipped with

a Surround-Sound system.

Surround Sound requires

the use of additional

speakers being placed

around your room.

Press "M" to Continue

Please thoroughly read

the section in your

owners manuel which

details the proper setup

and operation of the

Surround-Sound System.

Press "M" to Continue

Smart Нелл»

Remember, SETUP is a first -use,
one-time operation and will not

i have to be repeated (only the clock set

tings can be lost).

• Press the STATUS button on the remote or
TV to stop the SETUP at any time.

If there is RED or BLUE

fringe on the WHfTE cross,

use this adjustment to

improve the picture.

Press "M" to Continue

-or-

Press "k" to Return

This completes the

First-Time Setup.

Press "M" to Exit Setup

• Even if there is no Antenna or Cable signal
connected to the ANT(enna) B input (located
on the rear of the TV), 1st Time Setup will
still attempt to add channels into memoiy for
that source. In such cases, a channel search
in the Antenna Mode will be completed, and

“0 channels saved in memory” will be dis
played on-screen.

2 - EL6239 E001

• When setting the Smart Clock (Set Time
Automatically), enter your local PBS channel
number when it is requested on-screen.

• When setting the Time Manually use the
remote's number (or Menu AV) buttons to
enter the time for the TV's clock. Press "0"
with single digit hour entries when using the

number buttons on the remote.