Philips 74hc hct93 DATASHEETS

INTEGRATED CIRCUITS

DATA SH EET

For a complete data sheet, please also download:

•The IC06 74HC/HCT/HCU/HCMOS Logic Family Specifications

•The IC06 74HC/HCT/HCU/HCMOS Logic Package Information

•The IC06 74HC/HCT/HCU/HCMOS Logic Package Outlines

74HC/HCT93

4-bit binary ripple counter

Product specification
File under Integrated Circuits, IC06

December 1990

Philips Semiconductors Product specification

4-bit binary ripple counter 74HC/HCT93

FEATURES

• Various counting modes

• Asynchronous master reset

• Output capability: standard

• ICC category: MSI

divide-by-two section and a
divide-by-eight section. Each section
has a separate clock input (

CP0 and
CP1) to initiate state changes of the
counter on the HIGH-to-LOW clock
transition. State changes of the Q

n

outputs do not occur simultaneously
because of internal ripple delays.

GENERAL DESCRIPTION

The 74HC/HCT93 are high-speed
Si-gate CMOS devices and are pin
compatible with low power Schottky
TTL (LSTTL). They are specified in
compliance with JEDEC standard
no. 7A.

The 74HC/HCT93 are 4-bit binary
ripple counters. The devices consist
of four master-slave flip-flops
internally connected to provide a

Therefore, decoded output signals
are subject to decoding spikes and
should not be used for clocks or
strobes.

A gated AND asynchronous master
reset (MR1 and MR2) is provided
which overrides both clocks and
resets (clears) all flip-flops.

Since the output from the
divide-by-two section is not internally
connected to the succeeding stages,

QUICK REFERENCE DATA

GND = 0 V; T

=25°C; tr=tf= 6 ns

amb

SYMBOL PARAMETER CONDITIONS

t

PHL

f

max

C
C

I
PD

/ t

PLH

propagation delay CP0 to Q
maximum clock frequency 100 77 MHz

0

CL= 15 pF; VCC=5 V

input capacitance 3.5 3.5 pF
power dissipation capacitance per package notes 1 and 2 22 22 pF

the device may be operated in various
counting modes. In a 4-bit ripple
counter the output Q0 must be
connected externally to input CP1.
The input count pulses are applied to
clock input CP0. Simultaneous
frequency divisions of 2, 4, 8 and 16
are performed at the Q0, Q1, Q2 and
Q3 outputs as shown in the function
table. As a 3-bit ripple counter the
input count pulses are applied to input
CP1.
Simultaneous frequency divisions of
2, 4 and 8 are available at the Q1, Q
and Q3 outputs. Independent use of
the first flip-flop is available if the reset
function coincides with reset of the
3-bit ripple-through counter.

TYPICAL

UNIT

HC HCT

12 15 ns

2

Notes

1. C

is used to determine the dynamic power dissipation (PD in µW):

PD

PD=CPD× V

2

× fi+∑(CL× V

CC

2

× fo) where:

CC

fi= input frequency in MHz; fo= output frequency in MHz
∑ (CL× V

2

× fo) = sum of outputs

CC

CL= output load capacitance in pF; VCC= supply voltage in V

2. For HC the condition is VI= GND to VCC; for HCT the condition is VI= GND to VCC− 1.5 V

ORDERING INFORMATION

“74HC/HCT/HCU/HCMOS Logic Package Information”

See

.

December 1990 2

Philips Semiconductors Product specification

4-bit binary ripple counter 74HC/HCT93

PIN DESCRIPTION

PIN NO. SYMBOL NAME AND FUNCTION

1
2, 3 MR
4, 6, 7, 13 n.c. not connected
5V
10 GND ground (0 V)
12, 9, 8, 11 Q
14

CP

CP

1

CC

to Q

0

0

, MR

1

clock input 2nd, 3rd and 4th section (HIGH-to-LOW, edge-triggered)

2

asynchronous master reset (active HIGH)

positive supply voltage

3

flip-flop outputs
clock input 1st section (HIGH-to-LOW, edge-triggered)

Fig.1 Pin configuration. Fig.2 Logic symbol. Fig.3 IEC logic symbol.

December 1990 3