Philips 74AVC16836 Datasheet

INTEGRATED CIRCUITS

74AVC16836

20-bit registered driver with inverted register enable (3-State)

Preliminary specification

Replaces datasheet 74AVC16836/74AVCH16836 dated 1998 Dec 07

 

1999 Jul 23

Philips Semiconductors Preliminary specification

1

CPDPower dissi ation ca acitance er buffer

V

GND to V

1

F

20-bit registered driver with inverted register enable (3-State)

FEATURES

•Wide supply voltage range of 1.2 V to 3.6 V

•Complies with JEDEC standard no. 8-1A/5/7.

•CMOS low power consumption

•Input/output tolerant up to 3.6 V

•DCO (Dynamic Controlled Output) circuit dynamically changes

output impedance, resulting in noise reduction without speed degradation

•Low inductance multiple V

and GND pins for minimum noise

CC

and ground bounce

•Power off disables 74AVC16836 outputs, permitting Live Insertion

DESCRIPTION

The 74AVC16836 is a 20-bit universal bus driver. Data flow is controlled by output enable (OE (CP).

This product is designed to have an extremely fast propagation delay and a minimum amount of power consumption.

To ensure the high-impedance state during power up or power down, OE

should be tied to VCC through a pullup resistor (Live Insertion).

A Dynamic Controlled Output (DCO) circuitry is implemented to support termination line drive during transient. See the graphs on page 8 for typical curves.

), latch enable (LE) and clock inputs

PIN CONFIGURATION

1 2

Y

0

3

Y

1

4

GND

5

Y

2

6

Y

3

7

V

CC

8

Y

4

9

Y

5

Y

10

6

GND

11

Y

12

7

Y

13

8

14

Y

9

15

Y

10

16

Y

11

17

Y

12

18

GND

19

Y

13

20

Y

14

21

Y

15

22

V

CC

23

Y

16

24

Y

17

25

GND

26

Y

18

27

Y

19

28 29

NC

74A VC16836

CP

56OE

A

55

0

54

A

1

53

GND

52

A

2

51

A

3

50

V

CC

49

A

4

48

A

5

A

47

6

GND

46

A

45

7

A

44

8

43

A

9

42

A

10

41

A

11

40

A

12

39

GND

38

A

13

37

A

14

36

A

15

35

V

CC

34

A

16

33

A

17

32

GND

31

A

18

30

A

19

LE

QUICK REFERENCE DA TA

GND = 0 V; T

SYMBOL

t

PHL/tPLH

t

PHL/tPLH

C

I

NOTES:

1. C

is used to determine the dynamic power dissipation (PD in µW):

PD

= CPD × V

P

D

= output frequency in MHz; VCC = supply voltage in V; S (CL × V

f

o

= 25°C; tr = tf ≤ 2.0 ns; CL = 30 pF.

amb

Propagation delay An to Yn

Propagation delay LE to Yn; CP to Yn

Input capacitance 5.0 pF

2

× fi + S (CL × V

CC

ORDERING INFORMATION

56-Pin Plastic Thin Shrink Small Outline (TSSOP) Type II –40°C to +85°C 74AVC16836 DGG SOT364-1

1999 Jul 23

SH00159

PARAMETER CONDITIONS TYPICAL UNIT

p

CC

p

2

PACKAGES

VCC = 1.8 V VCC = 2.5 V VCC = 3.3 V

p

× fo) where: fi = input frequency in MHz; CL = output load capacitance in pF;

=

I

CC

2

× fo) = sum of outputs.

TEMPERATURE

RANGE

Outputs enabled 25

Output disabled 6

ORDER CODE

2.6

2.0

1.7

3.0

2.4

2.0

2

ns

p

DRAWING

NUMBER

Philips Semiconductors Preliminary specification

OUTPUTS

20-bit registered driver with inverted register enable (3-State)

PIN DESCRIPTION

PIN NUMBER SYMBOL NAME AND FUNCTION

28 NC No connection

2, 3, 5, 6, 8, 9, 10, 12, 13, 14, 15, 16, 17, 19,

Y0 to Y19Data outputs

20, 21, 23, 24, 26, 27

4, 11, 18, 25, 32, 35, 39,

46, 53

7, 22, 35, 50 V

1 OE

29 LE

GND Ground (0V)

Positive supply voltage

CC

Output enable input (active LOW)

Latch enable input (active LOW)

56 CP Clock input

55, 54, 52, 51, 49, 48, 47, 45, 44, 43, 42, 41, 40, 38, 37, 36, 34, 33,

A0 to A19Data inputs

31, 30

LOGIC SYMBOL

OE

CP

LE

LOGIC SYMBOL (IEEE/IEC)

OE

CP

LE

Y Y Y Y Y Y Y Y Y

Y

10

Y

11

Y

12

Y

13

Y

14

Y

15

Y

16

Y

17

Y

18

Y

19

74A VC16836

1 56 29

2

0

3

1

5

2

6

3

8

4

9

5

10

6

12

7

13

8

14

9

15 16 17 19 20 21 23 24

26 27

EN1

2C3 C3 G2

1 ∇ 1

55

A

0

54

A

1

52

A

2

3D

51

A

3

49

A

4

48

A

5

47

A

6

45

A

7

44

A

8

43

A

9

42

A

10

41

A

11

40

A

12

38

A

13

37

A

14

36

A

15

34

A

16

33

A

17

31

A

18

30

A

19

A

0

D

Y

LE

CP

0

FUNCTION TABLE

INPUTS

SH00160

OE LE CP A

H X X X Z

TO THE 19 OTHER CHANNELS

L L X L L L L X H H

SH00163

L H ↑ L L L H ↑ H H L H H X Y L H L X Y

1

0

2

0

H = HIGH voltage level L = LOW voltage level X = Don’t care Z = High impedance “off” state ↑ = LOW-to-HIGH level transition

NOTES:

1. Output level before the indicated steady-state input conditions were established, provided that CP is high before LE goes low.

2. Output level before the indicated steady-state input conditions were established.

1999 Jul 23

3