Philips 51PP9303H, 51PP9303H-17B Quick start guide
3135 035 21351
Rear-projection
HDTV Monitor
Rear-projection
HDTV Monitor
Quick Use and Setup Guide
Quick Use and Setup Guide
VIDEO
S-VIDEO
L
Pb
Pr
VIDEO
S-VIDEO
L
AUDIO
L
R
AUDIO
L
R
G/Y
R/Pr
B/Pb
V
H
SYNC
L
R
AUDIO
HD INPUT-AV 4
INPUT-AV 2OUTPUT
INPUT-AV 1
ANTENNA IN 75Ω
Y
L
R
AUDIO
HD INPUT-AV 5
DVI
1
VIDEO
S-VIDEO
L
Pb
Pr
VIDEO
S-VIDEO
L
AUDIO
L
R
AUDIO
L
R
G/Y
R/Pr
B/Pb
V
H
SYNC
L
R
AUDIO
HD INPUT-AV 4
INPUT-AV 2OUTPUT
INPUT-AV 1
ANTENNA IN 75Ω
Y
L
R
AUDIO
HD INPUT-AV 5
DVI
Back of TV
Back of Cable Box
(example only)
Cable TV
Signal
Back of TV
HOOKING UP THE TV
CONTENTS
Important Notice/Warning ............................................................1
Hooking up the TV ..................................................................1–2
Operating the Television and Remote Control ........................2–3
Using the Installation Features ................................................4–6
Using the Picture-in-Picture (PIP) Feature ..............................6–7
Adjusting the Manual Converge Controls....................................8
IMPORTANT
This owner's manual is used with several different television models.
Not all features (and drawings) discussed in this manual will necessarily match those found with your television set. This is normal and
does not require that you contact your dealer or request service.
BEST
V
IEWING
T
he major benefit of this projection television is its large view-
ing screen. To see this large screen at its best, test various
locations in the room to find the optimal spot for viewing.
NOTE: Be sure to allow a free flow of air to and from the perforated back cover of the set.
To avoid cabinet warping, cabinet color changes,
and increased chance of set failure, do not place
the TV where temperatures can become excessively
hot—for example, in direct sunlight or near a
heating appliance.
Magnetic fields, such as those of external speakers, may cause the picture to distort if the speakers are placed too close to the television. Move
the magnetic field source away from the TV until
there is no picture distortion.
As an Energy Star®
Partner, Philips Consumer
Electronics has determined
this product meets the Energy
Star® guidelines for energy
efficiency. Energy Star® is a
U.S. registered mark. Using
products with the Energy
Star® label can save energy.
Saving energy reduces air pollution and lowers utility bills.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS UNIT TO RAIN OR EXCESSIVE MOISTURE.
CABLE TV
CABLE BOX WITH RF IN/OUT
T
his connection WILL supply Stereo sound to the TV.
1
Connect the cable TV signal to the ANTENNA IN 75Ω
jack on the back of the TV.
NOTE: Refer to the sections on TUNER MODE and AUTO
PROGRAM on page 4 of this guide. Set TUNER MODE to
the CABLE option. Run AUTO PROGRAM to store all
available cable channels in the TV’s memory.
T
his is for example purposes only. The back of your cable box
may be labeled somewhat differently.
This connection WILL NOT supply stereo sound to the TV.
1
Connect the cable TV signal to the CABLE INjack on
the back of the cable box.
2
Connect a coaxial cable (not supplied) to the TO TV
jack on the back of the cable box and to the ANTENNA
IN 75Ω jack on the back of the TV.
3
Be sure to set the Output Channel switch on the back of
the cable box to CH 3 or 4, then tune the cable box on the
TV to the corresponding channel. Once tuned, change
channels at the cable box, not the TV.
Cable TV
Signal
CABLE BOX WITH A/V OUTPUTS
Cable TV
Signal
Back of TV
Back of Cable Box
(example only)
T
his is for example purposes only. The back of your cable box
may be labeled somewhat differently.
This connection MIGHT supply stereo sound to the TV. Check
with your cable TV company.
1
Connect the incoming cable TV signal to a signal splitter.
2
Connect a coaxial cable to a connector on the signal splitter
and to the ANTENNAIN 75Ω jack on the back of the TV.
3
Connect a coaxial cable to a connector on the signal splitter
and to the CABLE IN jack on the back of the cable box.
4
Connect A/V cables to the VIDEO and AUDIO L and R
outputs on the back of the cable box and to the INPUT-AV 2
VIDEO and corresponding AUDIO L and R jacks on the
back of the TV.
5
Plug in the cable box and TV and turn them on. Then,
while pointing the TV remote at the TV, press the AV button
repeatedly until AV2 is selected. This will allow the viewing
of programs through the cable box.
Signal
Splitter
1
CABLE
IN
3
OUTPUT
CH
3 4
TO TV
ANTENNA IN 75Ω
S-VIDEO
VIDEO
L
2
INPUT-AV 1
L
AUDIO
R
HD INPUT-AV 5
DVI
HD INPUT-AV 4
G/Y
INPUT-AV 2OUTPUT
Y
VIDEO
S-VIDEO
Pb
Pr
L
L
AUDIO
R
R/Pr
B/Pb
V
L
L
SYNC
AUDIO
AUDIO
H
R
R
ACTIVE
CONTROL
SWAP PIP CH
CABLE
IN
TO
TV
3
OUTPUT
CH
3 4
LR
VIDEO
AUDIO
OUT
OUT
STATUS/
VOL
SOUND
EXIT
ANTENNA IN 75Ω
2
INPUT-AV 1
VIDEO
S-VIDEO
L
L
AUDIO
R
4
TV/VCR
RECORD
A/CH
SURF
REC •
SAP
ITR/
HD INPUT-AV 5
DVI
HD INPUT-AV 4
G/Y
INPUT-AV 2OUTPUT
Y
VIDEO
S-VIDEO
Pb
Pr
L
L
AUDIO
R
R/Pr
B/Pb
V
L
L
SYNC
AUDIO
AUDIO
H
R
R
1
FREEZE
DN
UP
PICTURE
MENU/
SELECT
MUTE
CH
213
546
879
SURF
0
PIP ON/OFF
SLEEP
FORMAT
PROG.LISTDOLBY VAV
HOME
HOME
PERSONAL
VIDEO
MOVIES
PIPPOSITION
5
U
SING THE TV BUTTONS
S
hould your remote control be lost or broken, you can still
change some of the basic picture and sound settings with the
buttons on the TV. Follow the steps below to familiarize yourself
with the functions of the TV buttons.
1
Press POWER/STANDBY to turn the TV on (or off).
Allow about 10 seconds for the TV to power on.
2
Press the VOLUME + or – buttons to decrease or
increase the sound level.
Press the VOLUME + and – buttons simultaneously to display the on-screen menu. After the menu appears, use these
buttons to enter submenus and make selections or adjustments. (Use the CHANNEL buttons to move up and down
in the menu or submenus.) Press both VOLUME buttons
simultaneously to back out of the on-screen menus.
3
Press SOURCE SELECT to choose from among the signal inputs you have connected to the TV.
4
Press the CHANNEL buttons to select TV channels.
O
PERATING THE
TELEVISION AND R
EMOTE CONTROL
TELEVISION
R
EMOTE CONTROL
HOOKING UP THE TV
INSTALLING BATTERIES
T
o load the supplied batteries into the remote, follow these
steps.
1
Gently press and hold the indention on the back of the
remote and slide the battery cover off the remote.
2
Place the two “AA” size batteries in the remote’s battery case. Ensure that the (+) and (–) ends of the batteries
line up correctly with the (+) and (–) inside the case.
3
Slide the battery cover back into place.
POINTING THE REMOTE
Press the TV mode button on the remote to ensure that the
remote sends its commands to the TV. When operating the remote
control, point the remote toward the remote sensor window on the
TV.
To prevent battery leakage that
may result in injury to you or damage to the remote control:
• Install ALL batteries correctly, + and –,
as marked on the unit.
• Do not mix batteries (OLD and NEW
or CARBON and ALKALINE, etc.)
• Remove batteries when the remote
control is not used for a long time.
Do not take apart, heat, or put batteries in fire.
Remote Sensor
Window
You can set up your TV remote control to work with accessory
devices such as VCRs, DVD players, and cable converter boxes.
See pages 18–23 in the Directions for Use manual.
cc
C
HECK IT OUT
2
BATTERY USAGE CAUTION
Power/Standby
Button
You can press any of the buttons on
the front of the TV to turn the TV on,
but you must press the Power/
Standby button to turn the set off.
HELPFUL
HINT
Back of TV
Antenna Signal
ANTENNA TV
T
his connection WILL supply stereo sound to the TV.
Connect the antenna signal to the ANTENNAIN 75Ω jack on the
back of the TV.
NOTE: Refer to the sections on TUNER MODE and AUTO PROGRAM on page 4 of this guide. Set TUNER MODE to the
ANTENNA option. Run AUTO PROGRAM to store all available
cable channels in the TV’s memory.
• Be sure to point the remote toward the
sensor window on the TV or accessory
device you wish to operate.
• Press the correct mode button for the
device: TV, VCR, ACC (for accessories
other than VCRs).
• Be within about 30 feet (10 meters) of
the TV or accessory device you wish to
operate.
• Avoid dropping the remote on hard sur-
faces.
• Do not use harsh chemicals to clean the
remote. Use only a soft, lightly moistened cloth.
HELPFUL HINTS
ANTENNA IN 75Ω
S-VIDEO
HD INPUT-AV 5
DVI
AUDIO
VIDEO
L
R
INPUT-AV 2OUTPUT
S-VIDEO
L
INPUT-AV 1
VIDEO
L
AUDIO
Y
Pb
L
Pr
R
HD INPUT-AV 4
G/Y
R/Pr
B/Pb
V
L
SYNC
AUDIO
H
R
AUDIO
L
R
-
A
VOLUME
MENU
+
A
?
CHANNEL
>
VOLUME
CHANNEL
-
+
A
A
?
MENU
SOURCE
SELECT
SOURCE
>
SELECT
R
E
W
O
P
TV
ACC
E
Z
E
E
E
VCR
R
IV
F
T
C
L
A
O
R
T
N
O
C
TV
K
O
H
C
IP
P
P
UP
U
P
I
U
P
A
W
N
S
D
DN
N
D
D
N
U
O
S
P
/
S
U
T
A
T
S
IT
X
E
TV MODE
Button
O
V
VCR
E
R
U
T
C
/
U
N
E
M
T
C
E
L
E
S
MUTE
L
1
1
4
4
ACC
CH
3
3
2
2
6
6
5
5
9
9
8
8
SURF
7
7
TV/VCR
H
/C
A
H
/C
A
CC
0
0
IP
P
N
IO
IT
S
O
P
3
A
DJUSTING OR SETTING MENU OPTIONS
A
menu is simply a list of options. You can adjust or set your
TV’s on-screen menu options by pressing buttons on the
remote control. The following steps will familiarize you with how
to use the remote control with the on-screen menu.
1
Press the TV mode button to ensure that the remote control is in TV mode.
2
Press the MENU/SELECT button to bring the menu to
the screen. Then, as necessary, press the CURSOR RING
DOWN or UP to highlight a menu option. Press the CURSOR RING RIGHT to enter the submenu for the option.
3
Within the submenu, press the CURSOR RING DOWN
or UP to highlight an option.
Based on the submenu you are in, you can press the CURSOR RING RIGHT or LEFT to make an adjustment, select
a setting, or enter a list or another submenu.
You can return to the submenu from a list by pressing the
CURSOR RING LEFT.
To go from a submenu to the previous menu, highlight the
option at the top of the screen and press the CURSOR
RING UP. You can also press MENU/SELECT to return to
the previous menu.
Press STATUS/EXIT to exit the menu.
Power
Press to turn the TV on or off.
Active Control™
Measures and corrects all incoming signals to provide the best picture-quality settings. (See page 56 in the Directions for Use manual.) Press to turn Active Control™ on or off. When Active
Control™ is on, it automatically and continuously controls
Sharpness and Noise Reduction settings.
Picture
Press to select an AutoPicture™ control. Choose from four factory-set
controls—Movies, Sports, Weak Signal, and Multimedia—and a
PERSONAL control that you set according to your own preferences
through the on-screen Picture menu. (See page 26 in the Directions
for Use manual.) The four factory-set controls will enhance the TV
picture according to the particular type of program you are watching.
It may also be used to enhance pictures with weak signals.
Menu/Select
Press to display the on-screen menu. Press to return to a higher menu
level.
Channel +/–
Press to select channels in ascending or descending order or cycle
through the signal inputs.
Mute
Press to turn the TV sound off. To restore the sound to its previous
level, press the button again. (See pages 17 and 53 in the Directions
for Use manual.)
Surf
Press to select previously entered channels. With the TV’s
AutoSurf™ control, you can place up to 10 favorite channels or
sources in memory. Then by pressing the Surf button, you can quickly
view the selected channels. (See page 27 in the Directions for Use
manual that came with the TV to learn how to select a series of your
favorite channels using the Surf button.)
Format
Press to select a picture-format mode for a video source connected to
the ANTENNA, AV1, CVI, A V2, or A V3 (side panel) inputs. Each
press of the button selects a different mode—4:3, EXPAND 4:3,
PANORAMA, WIDE SCREEN, or AUTO. Control the picture format of a video source connected to the HD inputs (AV4 or AV5) with
the HD set-top box or progressive-scan-capable DVD player providing the video source.
Sleep
Press to set the TV to automatically turn itself off after a period of
time. Choose 15, 30, 45, 60, 90, 120, 180, or 240 minutes before the
TV will automatically turn off. (See page 29 in the Directions for Use
manual.)
Program List
Press to display a list of channel numbers and their names. (See the
“Tuner Mode,” “Auto Program,” “Channel Edit,” and “Name” sections on pages 4–6 in this guide for setup.) Each channel will appear
as a selectable menu item. The current channel will be highlighted as
default. Five channels will be listed on screen at one time. Press the
Cursor Ring up or down to scroll the list and and highlight a channel.
Press the Cursor Ring right to tune to the highlighted channel.
Channels marked “Skipped” in the Channel Edit control will not
appear in the list. Each channel that is being blocked by AutoLock™
will appear with a padlock icon to indicate that the channel is not
viewable. (See page 28 in the Directions for Use manual.)
Dolby V
Press to select various factory surround sound listening modes.
Dolby* Virtual (Virtual Dolby Surround) (with Virtual
Dolby Surround signals)
Dolby Virtual uses two speakers to simulate the surround effect
produced by a multichannel system.
Incredible Surround™
• In Stereo sound mode—when Incredible Surround™ is turned
on—it seems as though the loudspeakers are spread farther apart
from each another.
• In Mono sound mode—when Incredible Surround™ is turned
on—enables you to hear a spatial sound effect.
(See page 35 in the Directions for Use manual.)
VCR control buttons
Press to pause, rewind, stop, play, or fast forward a videotape.
TV • VCR • ACC
(Mode buttons) Press to send remote signals to either the TV, VCRs,
or other accessory devices such as cable TV converters, satellite
receivers, DVDs, or laser disc players. (You may need to program the
remote to work accessory devices. See pages 18–23 in the Directions
for Use manual that came with your TV.)
PIP buttons: SWAP, PIP CH DN/UP, FREEZE
Press to operate the Picture-in-Picture (PIP) features. See page 7 in
this publication for more information on using these buttons.
Sound
Press to select an AutoSound™ control. (See page 25 in the
Directions for Use manual.) Choose from three factory-set controls—
Voice, Music, and Theatre—and a Personal control that you set
according to your own preferences through the on-screen Sound
menu. The three factory-set controls will tailor the TV sound to
enhance the type of program you are watching.
Status/Exit
Pressing the button once shows the current channel number, name (if
set), time (if set), Sleep Timer setting, and sound setting (stereo,
mono, SAP, or mute). Pressing the button twice shows the current
AutoLock™ settings. Pressing the button once when an on-screen
display is showing removes the on-screen display.
Cursor Ring
Up/Down: allows you to select the next or previous menu item in the
menu. Left/Right: allows you to access the submenus and adjust the
settings. When no on-screen displays or menus are present, use the
Cursor Ring Left/Right to select a picture format for a video source
connected to the ANTENNA, AV1, CVI, A V2, or AV3 (side panel
inputs) on the TV.
Volume +/–
Press to adjust the TV sound level.
Number Buttons
Press to select TV channels. When selecting single-digit channels,
press the number of the desired channel. The TV will pause for a few
seconds and then tune to the selected channel.
TV/VCR
Press while in VCR mode to view the playback of a videotape. Press
again to return to TV mode.
A/CH
Press to alternate between the currently viewed channel and the previously viewed channel.
Rec
¶¶
Press this button simultaneously with the 3 button when in VCR
mode to record.
SAP
Press to select between main sound and SAP (Second Audio
Program) when you tune to a program offering SAP. (See page 37 in
the Directions for Use manual.)
AV
Press repeatedly to view materials from any accessory devices you
have connected to the TV’s input jacks. (See page 24 in the
Directions for Use manual.)
Clock
Press to access the on-screen Timer menu, where you can set the time
for the TV’s clock or set the TV’s Timer features, such as channel
switchover, power on set, and power off set. (See page 5 of this publication for setting the time manually. See pages 39–43 in the Directions
for Use manual for information on using the TV’s Timer feature.)
Position
Press to move the PIP picture to any of the four corners of the screen.
Back Light button
Press to light the buttons on the remote control.
PIP
Press to turn PIP (picture-in-picture) on or off or control the size of
the PIP window. (See pages 6 and 7 of this publication for more
information on PIP.)
• If you don’t press any
remote buttons, the menu
will automatically disappear after about 20 seconds.
To bring the menu back,
press MENU/SELECT.
• Sometimes not all the menu
items are visible on the
screen. If more items exist in
the menu, a cursor arrow
will appear. Also, a bullet
will appear for each remaining item, up to a maximum
of three. This will help you
determine how many items
are left in the menu. Keep
pressing the CURSOR
RING DOWN until you display all items.
• Should your remote become
lost or otherwise unavailable
for use, you can use the buttons on the front of the TV
to access the on-screen menu
and make adjustments or settings. See page 2.
H
ELPFUL HINTS
R
EMOTE C
ONTROL
O
PERATING THE
T
ELEVISION AND
REMOTE CONTROL
Active Control, AutoPicture,
AutoSound, AutoSurf, and
Incredible Surround are trademarks
of Philips Consumer Electronics
North America. Copyright© 2003
Philips Consumer Electronics.
*Manufactured under license from
Dolby Laboratories. “Dolby” and
the double-D symbol are trademarks of Dolby Laboratories.
POWER
ACC
TV
VCR
ACTIVE
SWAP PIP CH
FREEZE
CONTROL
DN
UP
PICTURE
SOUND
MENU/
STATUS/
SELECT
EXIT
TV
SWAP PIP CH
SOUND
STATUS/
EXIT
VOL
TV/VCR
A/CH
ITR/
RECORD
POWER
ACTIVE
CONTROL
ACC
FREEZE
PICTURE
MENU/
SELECT
CH
VCR
DN
UP
MUTE
213
546
879
PIP ON/OFF
HOME
MOVIES
SURF
SLEEP
PROG.LISTDOLBY VAV
PERSONAL
PIPPOSITION
0
SURF
REC •
FORMAT
SAP
HOME
VIDEO
MENU
PICTURE
SOUND
FEATURES
INSTALL
1
TV
VCR
ACTIVE
SWAP PIP CH
CONTROL
DN
UP
SOUND
STATUS/
EXIT
MUTE
VOL
3
213
546
879
TV/VCR
A/CH
0
POSITION
Go from one submenu
to another and make
settings or adjustments.
TREBLE
BASS
BALANCE
AVL
INCR . SURROUND
POWER
ACC
FREEZE
PICTURE
MENU/
SELECT
CH
SURF
PIP
SOUND SUBMENU
SOUND
TREBLE 30
BASS
BALANCE
AVL
INCR . SURROUND
SOUND
BALANCE
AVL
INCR . SURROUND
HEADPHONE
STEREO MONO
STEREO STEREO
INSTALL SUBMENU
2
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
FEATURES SUBMENU
FEATURES
TIMER
AutoLock
PIP
CLOSED CAP
FORMAT
Make adjustments or
selections within a
submenu.
OR
AV3
AV4
1
2
3
Also from a Submenu,
enter a list to make
selections.
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
AV3
AV4
1
2
3
TIME
START TIME
STOP TIME
CHANNEL
ACTIVATE
TIMER SUBMENU
FEATURES
TIMER
TIME 8:06 PM
START TIME
STOP TIME
CHANNEL
ACTIVATE
Loading...