Philips 49PL4909/F8 Schematic

Service Manual

49” LCD TV

chassis PL14.22

Contents

TYPE A

49PFL4909/F7 PHILIPS (Serial No.: DS1, DS2) 49PFL4609/F7 PHILIPS (Serial No.: DS1, DS2) 49PFL4909/F8 PHILIPS (Serial No.: XA1, XA2, XA3)

TYPE B

49PFL4709/F8 PHILIPS (Serial No.: XA1)

This service manual contains information of different types of models. Make sure to refer to the section describing your model.

All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.

Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes.

with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law.

150701

IMPORTANT SAFETY NOTICE

The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a tiny spec of color. This is not to be considered a defect in the LCD screen.

Proper service and repair is important to the safe, reliable operation of all P&F Equipment. The service procedures recommended by P&F and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.

It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. P&F could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, P&F has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by P&F must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.

TABLE OF CONTENTS

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Electrical Adjustment Instructions [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

How to Initialize the LCD TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Firmware Renewal Mode [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

Block Diagrams [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6

Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

Wiring Diagrams [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1

[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2

Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1

Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1

SPECIFICATIONS

< TUNER / NTSC >

Description Condition Unit Nominal Limit

1. AFT Pull-In Range --- MHz ±2.3 ±2.1 TV.ch.4

2. Synchronizing Sens.

CA.ch.31 CA.ch.87

< TUNER / ATSC >

Description Condition Unit Nominal Limit

1. Received Freq. Range (-28dBm) --- kHz --- ±100

ch.4

2. ATSC Dynamic Range (min / max)

ch.10 ch.41

< LCD PANEL >

Description Condition Unit Nominal Limit

1. Native Pixel Resolution

2. Brightness (w / filter)

3. Viewing Angle

Horizontal

Verti cal

Horizontal

Verti cal

dBV dBV dBV

dBm dBm dBm

pixels pixels

cd/m

° °

18 18 18

---

1920 1080

2

300 ---

-88 to 88

20 20 23

-76/0

-76/+4

---

< VIDEO >

Description Condition Unit Nominal Limit

1. Over Scan

2. Color Temperature

3. Resolution (composite video)

Horizontal

Verti cal

--x y

<Measurement condition> Input signal: HDMI1 Raster (40/70IRE) 1080i@60 Measurement point: Screen center Measuring instrument: Aging time: 60min. (Retail MODE / 100IRE Raster HDMI

MODE setting of TV: Shipment setting / Retail MODE Ambient temperature: 25°C ±5°C

Horizontal

Verti cal

% %

°K 12000

Made of KONICA MINOLTA Luminance meter CA-310

1080i@60)

line line

5 5

0.272

0.278

400 350

5±5 5±5

--±3% ±3%

---

< AUDIO >

All items are measured across 8  load at speaker output terminal with L.P.F.

Description Condition Unit Nominal Limit

1.

Audio MAX Output (ATSC 0dBfs)

2. Audio Distortion (NTSC) 500mW: Lch/Rch % 0.5/0.5 2.0/2.0

Lch/Rch W 10.0/10.0 8.0/8.0

1-1 PL14.22SP

IMPORTANT SAFETY PRECAUTIONS

Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.

Safety Precautions for LCD TV Circuit

1. Before returning an instrument to the

customer, always make a safety check of the

entire instrument, including, but not limited to, the following items:

a. Be sure that no built-in protective devices are

defective and have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including but not limited to, nonmetallic control knobs, insulating fishpapers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or

permit it to be operated without all protective devices correctly installed and functioning. Servicers who defeat safety features or fail to perform safety checks may be liable for any resulting damage.

b. Be sure that there are no cabinet openings

through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, (1) spacing between the Liquid Crystal Panel and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover.

c. Antenna Cold Check - With the instrument AC

plug removed from any AC source, connect an electrical jumper across the two AC plug prongs. Place the instrument AC switch in the on position. Connect one lead of an ohmmeter to the AC plug prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the coaxial connector. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected before the instrument is returned to the customer. Repeat this test with the instrument AC switch in the off position.

d. Leakage Current Hot Check - With the

instrument completely reassembled, plug the AC line cord directly into a 120 V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1410, (50.7). With the instrument AC switch first in the on position and then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milli-ampere. Reverse the instrument power cord plug in the outlet and repeat the test.

READING SHOULD NOT BE ABOVE 0.5 mA

LEAKAGE

DEVICE

BEING

TESTED

TEST ALL EXPOSED METAL SURFACES

ALSO TEST WITH PLUG REVERSED USING AC ADAPTER PLUG AS REQUIRED

ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER OR BEFORE CONNECTING THE ANTENNA OR ACCESSORIES.

2. Read and comply with all caution and safety-

related notes on or inside the receiver cabinet, on the receiver chassis, or on the Liquid Crystal Panel.

CURRENT

TESTER

+

EARTH GROUND

_

2-1 LTVN_ISP

3. Design Alteration Warning - Do not alter or add to the mechanical or electrical design of this TV receiver. Design alterations and additions, including, but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video output connections, might alter the safety characteristics of this receiver and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and may make you, the servicer, responsible for personal injury or property damage resulting therefrom.

4. Hot Chassis Warning a. Some TV receiver chassis are electrically

connected directly to one conductor of the AC power cord and maybe safety-serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known earth ground. If a voltage reading in excess of

1.0 V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground.

b. Some TV receiver chassis normally have 85V

AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can be safety-serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection.

c. Some TV receiver chassis have a secondary

ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation material that must not be defeated or altered.

5. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts-be sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage, and, e. antenna wiring. Always inspect in all areas for pinched, out of place, or frayed wiring. Check AC power cord for damage.

6. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard.

7. Product Safety Notice - Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The product's safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are strictly inspected to confirm they comply with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.

2-2 LTVN_ISP

Precautions during Servicing

A. Parts identified by the # symbol are critical for

safety. Replace only with part number specified.

B. In addition to safety, other parts and assemblies

are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements. Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc.

C. Use specified internal wiring. Note especially:

1) Wires covered with PVC tubing

2) Double insulated wires

3) High voltage leads

D. Use specified insulating materials for hazardous

live parts. Note especially:

1) Insulation Tape

2) PVC tubing

3) Spacers

4) Insulators for transistors.

E. When replacing AC primary side components

(transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering.

F. Observe that the wires do not contact heat

producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.)

G. Check that replaced wires do not contact sharp

edged or pointed parts.

H. When a power cord has been replaced, check that

11~13 lb (5~6 kg) of force in any direction will not loosen it.

I. Also check areas surrounding repaired locations. J. Use care that foreign objects (screws, solder

droplets, etc.) do not remain inside the set.

K. When connecting or disconnecting the internal

connectors, first, disconnect the AC plug from the AC supply outlet.

L. When installing parts or assembling the cabinet

parts, be sure to use the proper screws and tighten certainly.

2-3 LTVN_ISP

Safety Check after Servicing

Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards.

1. Clearance Distance

When replacing primary circuit components, confirm specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)

Table 1: Ratings for selected area

Chassis or Secondary Conductor

Primary Circuit

AC Line Voltage Region

110 to 130 V

Note: This table is unofficial and for reference only. Be

sure to confirm the precise values.

U.S.A. or

Canada

Clearance

Distance (d), (d’)

 3.2 mm

(0.126 inches)

2. Leakage Current Test

Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below.

Measuring Method: (Power ON)

Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across both terminals of load Z. See Fig. 2 and following table.

d' d

Fig. 1

Exposed Accessible Part

Z

AC Voltmeter (High Impedance)

Earth Ground

B

Power Cord Plug Prongs

Fig. 2

Table 2: Leakage current ratings for selected areas

AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to:

110 to 130 V

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

U.S.A. or

Canada

0.15 F CAP. & 1.5 k

RES. Connected in parallel

2-4 LTVN_ISP

i  0.5 mA rms

Exposed accessible

parts

STANDARD NOTES FOR SERVICING

Top View

Out

In

Bottom View

Input

5

10

Pin 1

Circuit Board Indications

1. The output pin of the 3 pin Regulator ICs is indicated as shown.

2. For other ICs, pin 1 and every fifth pin are indicated as shown.

3. The 1st pin of every male connector is indicated as shown.

Pb (Lead) Free Solder

Pb free mark will be found on PCBs which use Pb free solder. (Refer to figure.) For PCBs with Pb free mark, be sure to use Pb free solder. For PCBs without Pb free mark, use standard solder.

Pb free mark

How to Remove / Install Flat Pack-IC

1. Removal

With Hot-Air Flat Pack-IC Desoldering Machine:

1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1)

Fig. S-1-1

2. Remove the flat pack-IC with tweezers while applying the hot air.

3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)

4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)

CAUTION:

1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC.

2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2)

3-1 TVN_SN

3. The flat pack-IC on the CBA is affixed with glue, so

Hot-air Flat Pack-IC Desoldering Machine

CBA

Flat Pack-IC

Tweezers

Masking Tape

Fig. S-1-2

be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it.

With Soldering Iron:

1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)

Flat Pack-IC

Desoldering Braid

Soldering Iron

Fig. S-1-3

2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4)

Sharp Pin

Fine Tip Soldering Iron

3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)

4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)

Fig. S-1-4

3-2 TVN_SN

With Iron Wire:

To Solid Mounting Point

Soldering Iron

Iron Wire

or

Hot Air Blower

Fig. S-1-5

Fine Tip Soldering Iron

CBA

Flat Pack-IC

Tweezers

Fig. S-1-6

1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)

2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5.

3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5.

4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)

5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)

Note: When using a soldering iron, care must be

taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied.

2. Installation

1. Using desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily.

2. The “ I ” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the pin 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.)

3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges.

Example :

Pin 1 of the Flat Pack-IC is indicated by a " " mark.

Fig. S-1-7

Presolder

Flat Pack-IC

CBA

Fig. S-1-8

3-3 TVN_SN

Instructions for Handling Semi-

CBA

Grounding Band

Conductive Sheet or Copper Plate

1MΩ

CBA

conductors

Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.

1. Ground for Human Body

Be sure to wear a grounding band (1 M) that is properly grounded to remove any static electricity that may be charged on the body.

2. Ground for Workbench

Be sure to place a conductive sheet or copper plate with proper grounding (1 M) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing.

3-4 TVN_SN

CABINET DISASSEMBLY INSTRUCTIONS

[5] Digital Main

CBA Unit

[4] Power Supply

CBA

[1] Stand Base

Assembly

[3] Rear

Cabinet L

[6] Stand Bracket

[8] Speaker

[11] IR Sensor

CBA Unit

[12] LCD Panel

Assembly

[10] Function

CBA Unit

[7] T-CON Holder

[9] Speaker

Holder

[2] Rear

Cabinet R

Screw Torque Specification

Ref.

No.

L10 GCHP3120

L23 GBJS3060

L28 GCHS3080

L45 FPH34100

SSK1 1ESA34506

* For reference

Part

Number

Part Name

SCREW F-PAN BLACK_NI +P-TITE M3X12.0

SCREW BIND 3CHROM +S-TITE M3X6.0

SCREW F-PAN BLACK_NI +S-TITE M3X8.0

SEMS-SW PAN BLACK_NI + M4X10.0

STAND SCREW KIT (SEMS-SW PAN BLACK_NI + M4X12.0)

Tightening

Torque

5.2±0.9lb·in

(approx.

8.7±0.9lb·in)

1. Disassembly Flowchart

This flowchart indicates the disassembly steps for the

cabinet parts and the CBA in order to gain access to items to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were.

Step/

Loc.

No.

Power

[4]

Supply CBA

Digital Main

[5]

CBA UnitD2D5

Part

Fig.

No.

5(S-8), CN501,

D2

CN601, CN1101,

D5

CN1301 4(S-9), CN3013

CN3101 CN3801, CN3906

Removal Note

---

*2

, CN3105*1,

,

---

*1

Jack Holder

Stand

[6]

[7]

Bracket T- C O N

Holder

*

D3 --------------- ---

D3 (S-10) ---

[8] Speaker D3 Hook ---

Speaker

[9]

Holder

Function

[10]

CBA UnitD3D5

IR Sensor

[11]

CBA UnitD3D5

D3 2(S-11) ---

CN4051, Function Knob, Knob Frame,

2

Hook

Sensor Shield, Hook 2

2. Disassembly Method

Step/

Loc.

No.

Stand Base

[1]

Assembly Rear

[2]

Cabinet R Rear

[3]

Cabinet L

Part

Fig.

No.

D1 8(S-1), Stand Neck ---

D1

Removal Note

10(S-2), 6(S-3), 2(S-4), 2(L-1)

7(S-5), 4(S-6), 2(S-7), (L-2)

---

Decoration Plate, LED

D4

Lens, Leading Edge Cover, Hook



(3)



(4)

1



(5)

[12]



(1)

LCD Panel Assembly



(2)

*1: TYPE A

*2: TYPE B

Note:

(1) Order of steps in procedure. When reassembling,

follow the steps in reverse order. These numbers are also used as the Identification (location) No. of parts in figures.

(2) Parts to be removed or installed. (3) Fig. No. showing procedure of part location (4) Identification of parts to be removed, unhooked,

unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, H = Hex Screw, CN = Connector e.g. 2(S-2) = two Screws of (S-2), 2(L-2) = two Locking Tabs of (L-2)

(5) Refer to the following “Reference Notes in the

Ta bl e .”

4-1 PL14.22-A_DC

Important precautions concerning the LCD Panel Assembly:

1. When you disassemble/re-assemble the LCD Panel Assembly

• Do not pull the FFC Cable and Board Cable

forcefully when you re-assemble.

• Be careful not to scratch the display panel when

assembling.

2. When you disassemble/re-assemble the Function CBA Unit or the IR Sensor CBA Unit

• Be careful not to break the hooks. If you pull with too

much force, the hooks may be damaged.

• Make sure the hooks are securely in place when

assembling.

• The Function CBA Unit and Function Knob are fixed

in place by the hooks. Make sure these hooks are not damaged. Make sure the Function CBA Unit and Function Knob are securely in place when reassembling.

• The IR Sensor CBA Unit and Sensor Shield are

fixed in place by the hooks. Make sure these hooks are not damaged. Make sure the IR Sensor CBA Unit and Sensor Shield are securely in place when re-assembling.

4-2 PL14.22-A_DC

[1] Stand Base Assembly

Stand Neck

(S-5)

(S-6)

(S-7)

(S-2)

(L-1)

(L-2)

(L-1)

(S-4)

[3] Rear Cabinet L

[2] Rear Cabinet R

(S-1)

(S-1) (S-1)

(S-3)

49PFL4909/F7, 49PFL4709/F8, 49PFL4909/F8 49PFL4609/F7

Fig. D1

4-3 PL14.22-A_DC

[TYPE A] [TYPE B]

[4] Power Supply CBA

(S-9)

[5] Digital Main CBA Unit

(S-8)

Jack Holder

Fig. D2

4-4 PL14.22-A_DC

Sensor Shield

*2: Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the

Function CBA Unit or the IR Sensor CBA Unit.

[9] Speaker Holder

2

*

Hook

2

*

(S-11)

[8] Speaker

[11] IR Sensor

2

CBA Unit

*

(S-11)

[10] Function

2

CBA Unit

Function Knob

Wire of Function CBA Unit Wire of Speaker

*

2

*

Hook

Knob Frame

2

*

2

*

Hook

[8] Speaker

[7] T-CON Holder

Hook

(S-10)

[6] Stand Bracket

Hook

Fig. D3

4-5 PL14.22-A_DC

Decoration Plate

*1: Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the LCD

Panel Assembly.

Leading Edge Cover

1

[12] LCD Panel Assembly

1

*

1

LED Lens

1

*

Hook

1

*

Fig. D4

4-6 PL14.22-A_DC

TV Cable Wiring Diagram

[TYPE A]

Function CBA Unit

Power Supply CBA

CN1101

To LCD Panel Assembly

CN1301

CN501

CN601

To LCD Panel Assembly

CN3906

CN3601

CN3105

Digital Main CBA Unit

CN3801

CN4001

To AC Cord

To Speaker

CN4051

IR Sensor CBA Unit

CN4052

Fig. D5

4-7 PL14.22-A_DC

[TYPE B]

Power Supply CBA

To LCD Panel Assembly

CN1101

CN1301

Digital Main CBA Unit

Function CBA Unit

CN4001

CN501

CN601

IR Sensor CBA Unit

To AC Cord

CN4051

CN4052

CN3013

CN3602

CN3101

CN3801

To Speaker

Fig. D5

4-8 PL14.22-A_DC

ELECTRICAL ADJUSTMENT INSTRUCTIONS

[current] File code: Total checksum: Panel-Option code:

Press "POWER" key to exit.

***-****_***_* Push "0" key **-***-***-***-***-***

***-***-***-***-***

Flicker: Tuner: HDMI UART: Touch Sensor Ver: EDID:

***** **** OFF

------ / -.--.-Push "0" key

MAC address: ESN:

**:**:**:**:**:** *****************************

Total Watch Time: System Time: Lightsensor:

***** **:** **

"*" differs depending on the models.

[TYPE A]

General Note: “CBA” is abbreviation for “Circuit Board Assembly.”

Note: Electrical adjustments are required after

replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.

Test Equipment Required

1. Remote control unit

2. Color Analyzer, CA-310 (KONICA MINOLTA Luminance meter) or measuring instrument as good as CA-310.

How to set up the service mode:

Service mode:

1. Turn the power on.

2. Press [0], [6], [2], [5], [9], [6] and [INFO] buttons on the remote control unit in this order. The following screen appears.

1. Purity Check Mode

This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.

1. Enter the service mode.

2. Each time the [7] button on the remote control unit is pressed, the display changes as follows.

Purity Check Mode

White mode

[7] button

Black mode

[7] button

White 50% mode

[7] button

Red, Green, Blue mode

[7] button

V-ramp mode

[7] button

White 20% mode

Note:

When entering this mode, the default setting is White mode.

3. To cancel or to exit from the Purity Check Mode, press [CH RETURN] or [PREV CH] button.

5-1 PL14.22EA

The White Balance Adjustment should be

Color Analyzer

Perpendicularity

To avoid interference from ambient light, this adjustment should be performed in a dark room.

performed when replacing the LCD Panel or Digital Main CBA.

2. White Balance Adjustment

Purpose: To mix red and blue beams correctly for

pure white. Symptom of Misadjustment: White becomes bluish

or reddish.

5. Press [3] button to select the “HDB” for High Drive Blue adjustment. (“HDB” appears in the screen.)

6. Press [MENU] button. The internal Raster signal appears in the screen. (“Internal (Single)” appears in the upper right of the screen as shown below.)

Internal (Single)

ITEM

Color temperature

Input Signal

SPECIFICATION

x= 0.272 ± 0.003 y= 0.278 ± 0.003

Internal pattern (30/50/80% raster)

Measurement point Screen center

CA-310 (KONICA MINOLTA

M. EQ.

Luminance meter) or measuring instrument as good as CA-310.

60min.

Aging time

(Retail MODE/100IRE Raster HDMI 1080i@60)

MODE setting of TV

Ambient temperature

Shipment setting/ Retail MODE

25°C ± 5°C

1. Operate the unit for more than 30 minutes.

2. Enter the service mode.

3. Press [VOLUME DOWN] button three times on the remote control unit to select “Drive setting” mode. “Drive-” appears in the screen.

4. Set the color analyzer at the CHROMA mode and zero point calibration. Bring the optical receptor pointing at the center of the LCD-Panel.

HDB 0

7. Press [CHANNEL UP/DOWN] buttons to adjust the color temperature becomes 12000°K (x

=

0.272 / y= 0.278 ± 0.003).

8. Press [1] button to select the “HDR” for High Drive Red adjustment (“HDR” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.

9. If necessary, adjust the “HDB” or “HDR” again

10. Press [6] button to select the “MDB” for Middle Drive Blue adjustment (“MDB” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.

Internal (Single)

MDB 0

11. Press [4] button to select the “MDR” for Middle Drive Red adjustment (“MDR” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.

12. If necessary, adjust the “MDB” or “MDR” again.

Note: The optical receptor must be set

perpendicularly to the LCD Panel surface.

5-2 PL14.22EA

13. Press [9] button to select the “LDB” for Low Drive

Internal (Single)

LDB 0

Blue adjustment (“LDB” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.

14. Press [7] button to select the “LDR” for Low Drive Red adjustment (“LDR” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.

15. If necessary, adjust the “LDB” or “LDR” again.

16. Press [VOLUME DOWN] button to shift to the “Debugging Message” mode. If there is no message under “[WB]” section, this adjustment completes. If “Drive settings are NG. Retry again.” is displayed, repeat above steps from 5. to 15. Then check “Debugging Message” again. If “Drive settings are NG. Retry again.” is displayed, replace the LCD Panel or Digital Main CBA.

17. To cancel or to exit from the White Balance Adjustment, press [CH RETURN] or [PREV CH] button.

5-3 PL14.22EA

[TYPE B]

Code: Pic code: Panel-Option code: MIPS:

Press "POWER" key to exit.

*******-**-**-****-** **-***-**-*****-*** **-***-***-***-***

**

Safety: HDMI EDID: HDMI UART: Flicker: Touch Sensor Ver: :

Safety_Non ** OFF AUTO0

-.-- / ---

Total Watch Time: Lightsensor:

***** **

"*" differs depending on the models.

1. Purity Check Mode

General Note: “CBA” is abbreviation for “Circuit Board Assembly.”

Note: Electrical adjustments are required after

replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.

Test Equipment Required

1. Remote control unit

2. Color Analyzer, CA-310 (KONICA MINOLTA Luminance meter) or measuring instrument as good as CA-310.

How to set up the service mode:

Service mode:

1. Turn the power on.

2. Press [MENU] button to display Setup menu.

3. Select “Features”.

4. Select “Software Upgrade”.

5. Select “Current Software Info”.

6. Press [0], [6], [2], [5], [9], [6] and [INFO] buttons on the remote control unit in this order. The following screen appears.

This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.

1. Enter the service mode.

2. Each time the [7] button on the remote control unit is pressed, the display changes as follows.

Purity Check Mode

White mode

[7] button

Black mode

[7] button

White 50% mode

[7] button

Red, Green, Blue mode

[7] button

V-ramp mode

[7] button

White 20% mode

Note:

When entering this mode, the default setting is White mode.

3. To cancel or to exit from the Purity Check Mode, press [CH RETURN] or [PREV CH] button.

5-4 PL14.22BEA

The White Balance Adjustment should be

Color Analyzer

Perpendicularity

To avoid interference from ambient light, this adjustment should be performed in a dark room.

performed when replacing the LCD Panel or Digital Main CBA.

2. White Balance Adjustment

Purpose: To mix red and blue beams correctly for

pure white. Symptom of Misadjustment: White becomes bluish

or reddish.

6. Press [MENU] button. The internal Raster signal appears in the screen. (“Internal (Single)” appears in the upper right of the screen as shown below.)

Internal (Single)

ITEM

Color temperature

Input Signal

SPECIFICATION

x= 0.272 ± 0.003 y= 0.278 ± 0.003

Internal pattern (40/80% raster)

Measurement point Screen center

CA-310 (KONICA MINOLTA

M. EQ.

Luminance meter) or measuring instrument as good as CA-310.

60min.

Aging time

(Retail MODE/100IRE Raster HDMI 1080i@60)

MODE setting of TV

Ambient temperature

Shipment setting/ Retail MODE

25°C ± 5°C

1. Operate the unit for more than 60 minutes.

2. Enter the service mode.

3. Press [VOLUME DOWN] button three times on the remote control unit to select “Drive setting” mode. “Drive” appears in the screen.

4. Set the color analyzer at the CHROMA mode and zero point calibration. Bring the optical receptor pointing at the center of the LCD-Panel.

HDB 0

7. Press [CHANNEL UP/DOWN] buttons to adjust the color temperature becomes 12000°K (x

=

0.272 / y= 0.278 ± 0.003).

8. Press [2] button to select the “HDG” for High Drive Green adjustment (“HDg” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.

9. Press [1] button to select the “HDR” for High Drive Red adjustment (“HDR” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.

10. If necessary, adjust the “HDB”, “HDG” or “HDR” again.

11. Press [6] button to select the “LDB” for Low Drive Blue adjustment (“LDB” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.

Internal (Single)

Note: The optical receptor must be set

perpendicularly to the LCD Panel surface.

5. Press [3] button to select the “HDB” for High Drive Blue adjustment. (“HDB” appears in the screen.)

LDB 0

12. Press [5] button to select the “LDG” for Low Drive Green adjustment (“LDG” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.

13. Press [4] button to select the “LDR” for Low Drive Red adjustment (“LDR” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.

14. If necessary, adjust the “LDB”, “LDG” or “LDR” again.

5-5 PL14.22BEA

15. Press [VOLUME DOWN] button to shift to the “Debugging Message” mode. If there is no message under “[WB]” section, this adjustment completes. If “Drive settings are NG. Retry again.” is displayed, repeat above steps from 5. to 14. Then check “Debugging Message” again. If “Drive settings are NG. Retry again.” is displayed, replace the LCD Panel or Digital Main CBA.

16. To cancel or to exit from the White Balance Adjustment, press [CH RETURN] or [PREV CH] button.

5-6 PL14.22BEA

HOW TO INITIALIZE THE LCD TV

The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized. To put the program back at the factory-default, initialize the LCD TV using the following procedure.

NOTE: Disconnect any device from the USB Port

before you conduct on this procedure.

[TYPE A]

1. Turn the power on.

2. Enter the service mode.

- To cancel the service mode, press [ ] button on

the remote control unit.

3. Press [BACK] button to enter the Control Panel Key Confirmation Menu.

4. Press all buttons on the control panel.

5. Press [INFO] button to proceed with the self check mode.

6. Make sure to confirm the "INITIALIZED : OK" appears in the green screen.

7. Unplug the AC Cord and plug it back on again.

[TYPE B]

1. Turn the power on.

2. Enter the service mode.

- To cancel the service mode, press [ ] button on

the remote control unit.

3. Press [BACK] button to enter the Control Panel Key Confirmation Menu.

4. Press any button on the control panel.

5. Press [INFO] button to proceed with the self check mode.

6. Make sure to confirm the "INITIALIZED FINISH" appears in the green screen.

7. Unplug the AC Cord and plug it back on again.

6-1 PL14.22INT

[TYPE A]

USB port

USB storage device

Rear Cabinet (example)

FIRMWARE RENEWAL MODE

Equipment Required

a. USB storage device b. Remote Control Unit

Firmware Update Procedure

1. Turn the power off and unplug the AC Cord.

2. Insert the USB storage device to the USB port as shown below.

Update file selection screen appears as follows. (Files included in the USB storage device are displayed.)

"*" differs depending on the models.

Select an upgrade file

Cancel

*****_******.upg

123

Note: To cancel the update mode, select “Cancel” and press the [OK] button.

10. Select the file and press [OK] button.

11. The update will start and the following will appear in the screen.

"*" differs depending on the models.

Current Version: ***-****-***-* New Version: ***-****-***-*

3. Plug the AC Cord and turn the power on.

4. After few seconds, the menu mode will appear in the screen.

Note:

After 30 seconds without an operation, the menu mode will disappear automatically. To display the menu mode again, press the [MENU] button on the remote control unit.

5. Select “Setup” and press the [OK] button to display the setup menu.

6. Select “Software”.

7. Select “Software update”.

8. Select “USB”.

9. Press the [OK] button on the remote control unit to enter the update mode.

Are you sure you want to update?

No Yes

Note:

If the above screen isn’t displayed, repeat from step 1.

12. Select “Yes” and press the [OK] button to update.

Note:

Do not remove the USB storage device or turn the TV off while update is in progress.

13. When the firmware update is completed, the following will appear in the screen.

Update your TV with new software: Done

Software update is successful.

Please remove the USB storage device

and restart the TV set.

Remove the USB storage device from the USB port. Turn the power off and turn the power on again.

7-1 PL14.22FW

[TYPE B]

USB port

USB storage device

Rear Cabinet

Equipment Required

a. USB storage device b. Remote Control Unit

Firmware Update Procedure

User Upgrade (Filename example: TVNB2001_00_PH_XX91_FB1.bin)

Upgrade the firmware only. The setting values will not be initialized. The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename. If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_” from the filename.

Update procedure

1. Turn the power on.

2. Press [MENU] button to display Menu.

3. Select “Features”.

4. Select “Software Upgrade”.

5. Select “Upgrade” to display Upgrade screen.

6. Press [OK] button to display Software Upgrade screen.

7. Select “USB” and press [OK] button.

8. Insert the USB storage device to the USB port as shown below.

11. The update will start and the following will appear in the screen.

"*" differs depending on the models.

Software Upgrade

Software upgrade in progress. Please wait. Do not remove the USB storage device or turn the TV off while upgrade is in progress.

*1

Current Version:

New Version:

Downloading...

0%

*******-***-*-***-**** *******-***-*-***-****

Note: If the above screen isn’t displayed, repeat from

step 1.

The appearance shown in *1 is described as follows.

Appearance State

Downloading...

Writing...

Downloading the firmware from the USB storage device.

Writing the downloaded firmware in flash memory.

Checking... Checking the new firmware.

9. Select “Check” and press [OK] button.

10. Select “Upgrade” and press [OK] button to start software upgrade.

12. When the firmware update is completed, the following will appear in the screen.

Software Upgrade

The software upgrade is completed. Remove USB storage device, turn TV off then on again.

Remove the USB storage device from the USB port. Turn the power off and turn the power on again.

7-2 PL14.22BFW

Factory Upgrade (Firmware Upgrade/Flash Upgrade)

USB port

USB storage device

Rear Cabinet

Software upgrade in progress. Please wait. Do not remove the USB storage device or turn the TV off while upgrade is in progress.

Software Upgrade

Downloading...

Current Version:

New Version:

*******-***-*-***-**** *******-***-*-***-****

0%

*1

"*" differs depending on the models.

Firmware Upgrade (Filename example: FACT_TVNB2001_00_PH_XX91_FB1.bin) Upgrade the firmware and initialize the setting values. The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename. If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_” from the filename.

Flash Upgrade (Filename example: ALL_TVNB2001_00_PH_XX91_FB1.bin) Upgrade the firmware and initialize the setting values along with the factory default such as White Balance, etc. Before the upgrade, you will need to make a note of all the factory default so you will be able to set it back on the TV after the initialization. The Flash Upgrade will be done by it's unique file. The User Upgrade/Firmware Upgrade (Factory Upgrade) file cannot be used for this upgrade.

Update procedure

1. Turn the power off.

2. Insert the USB storage device to the USB port as shown below.

The appearance shown in *1 is described as follows.

Appearance State

Downloading...

Writing...

Downloading the firmware from the USB storage device.

Writing the downloaded firmware in flash memory.

Checking... Checking the new firmware.

3. Turn the power on.

4. The update will start and the following will appear in the screen.

5. When the firmware update is completed, the following will appear in the screen.

Software Upgrade

The software upgrade is completed. Remove USB storage device, turn TV off then on again.

Remove the USB storage device from the USB port. Turn the power off and turn the power on again. Service mode initial screen with a word “INITIALIZED” will appear in the screen. The color of the word “INITIALIZED” will change from red to green when initialization is completed.

Note: If the above screen isn’t displayed, repeat from

step 1.

7-3 PL14.22BFW

TROUBLESHOOTING

Note:

This Troubleshooting section covers the entire PL14.22 chassis models. Thus some Reference number of parts shown below may not be used depending on the model. Please refer to the parts list for each model.

[Power Supply Section]

FLOW CHART NO.1

The power cannot be turned on.

Is the fuse (F602) normal?

Ye s

Is normal state restored when once unplugged power cord is plugged again after several seconds?

Ye s

Is the P-ON+21V line voltage normal?

Ye s

Check each rectifying circuit of the secondary circuit and repair it if defective.

FLOW CHART NO.2

The fuse blows out.

No

See FLOW CHART No.2 <The fuse blows out.>

Check if there is any leak or short-circuit on the primary circuit component and repair it if defective. (C625, C665, D601, D602, D603, D604, D605, D606, D607, D613, D618, D621A, D623, D664A, IC601, IC604, Q601, Q602, Q603, T601, R630, R631)

Check if there is any leak or short-circuit on the primary circuit component and repair it if defective.

Make sure to repair the primary circuit component before replacing the fuse(F602).

FLOW CHART NO.3

When the output voltage fluctuates.

Does the photocoupler circuit on the secondary side operate normally?

Ye s

Check D609A, D613, D614, D615, D619A, D620A, D621A, Q601, Q602, IC602 and their periphery circuit. Repair it if defective.

FLOW CHART NO.4

When buzz sound can be heard in the periphery of power circuit.

Check if there is any short-circuit on the rectifying diode and the circ Repair it if defective. (D650, D653, D655, Q703, Q705)

No

Check if there is any leak or short-circuit on the each rectifying circuit component of secondary side and repair it if defective.

Check IC602, D660 and their periphery circuit. Repair it if defective.

uit in each rectifying circuit of the secondary side.

8-1 PL14.22ATR

AL+3.3V is not output.

Replace Q705.

No

Ye s

No

FLOW CHART NO.7 [TYPE A]

Check if there is any leak or short-circuit on the load circuit. Repair it if defective.

AMP+13V is not output.

FLOW CHART NO.6

Is approximately +13V voltage supplied to the cathode of D653(D655)?

No

Ye s

Check C654, C655, D653, D654, D655 and their periphery circuit. Repair it if defective.

Check C654, C655, D653, D654, D655, R756 and their periphery circuit. Repair it if defective.

Check Q703, D715 and their periphery circuit. Repair it if defective.

Is approximately +13V voltage supplied to the emitter of Q705?

Is approximately +12V voltage supplied to the base of Q705?

Check if there is any leak or short-circuit on the load circuit. Repair it if defective.

P-ON+21V is not output.

Is approximately +21V voltage supplied to the cathode of D650?

No

Ye s

Check C651, C652, D650 and their periphery circuit. Repair it if defective.

FLOW CHART NO.5

8-2 PL14.22ATR

[Video Signal Section]

FLOW CHART NO.1

The key operation is not functioning.

When pressing each buttons, does the Pin(2) voltage of CN4001 decrease?

Ye s

Replace the Digital Main CBA Unit.

FLOW CHART NO.2

No operation is possible from the remote control unit. (Operation is possible from the unit.)

Is approximately +3.3V voltage supplied to Pin(1) of CN4052?

Ye s

Is the "L" pulse supplied to Pin(5) of CN4052 when the infrared remote control activated?

Ye s

Replace the Digital Main CBA Unit.

FLOW CHART NO.3 [TYPE A]

Picture does not appear normally.

No

Replace the Function CBA Unit.

Check AL+3.3V line and repair it if defective.

Replace the IR Sensor CBA Unit.

Is approximately +21V voltage supplied to Pin(20, 21, 22, 23) of CN501?

Ye s

approximately +

Is CN501?

Digital Main CBA Unit or LCD Panel Assembly may be defective. Check and replace these parts.

[TYPE B]

Picture does not appear normally.

Is approximately +21V voltage supplied to Pin(20, 21, 22, 23) of CN501?

Digital Main CBA Unit or LCD Panel Assembly may be defective. Check and replace these parts.

3.3V voltage supplied to Pin(8) of

Ye s

No

See FLOW CHART NO.5 <P-ON+21V is not output. [Power Supply Section]>

See FLOW CHART NO.7 <AL+3.3V is not output. [Power Supply Section]>

See FLOW CHART NO.5 <P-ON+21V is not output. [Power Supply Section]>

8-3 PL14.22ATR

[Audio Signal Section]

FLOW CHART NO.1 [TYPE A]

Audio is not output normally.

Is approximately +13V voltage supplied to Pin(15, 16, 17, 18) of CN501?

Ye s

approximately +

Is CN501?

Are the audio signals output to Pin(1, 2, 3, 4) of CN3801?

SP3801, SP3802 or CL3801 may be defective. Check and replace these parts.

[TYPE B]

Audio is not output normally.

Is approximately +13V voltage supplied to Pin(15, 16, 17, 18) of CN501?

Are the audio signals output to Pin(1, 2, 3, 4) of CN3801?

3.3V voltage supplied to Pin(8) of

Ye s

No

See FLOW CHART NO.6 <AMP+13V is not output. [Power Supply Section]>

See FLOW CHART NO.7 <AL+3.3V is not output. [Power Supply Section]>

Replace the Digital Main CBA Unit.

See FLOW CHART NO.6 <AMP+13V is not output. [Power Supply Section]>

Replace the Digital Main CBA Unit.

SP3801, SP3802 or CL3801 may be defective. Check and replace these parts.

8-4 PL14.22ATR

BLOCK DIAGRAMS

[TYPE A]

1. System Control Block Diagram

KEY SWITCH

FUNCTION CBA UNIT

CN4001

KEY-IN122

CN4051

P-ON+5V

LIGHT

REMOTE

RS4051

SENSOR

D4051

POWER

IC4051

SENSOR

TO

POWER SUPPLY

P-ON-H2

CN501

BLOCK DIAGRAM

RESET

TO

LED BACKLIGHT DRIVE

PROTECT3

BACKLIGHT-SW

CN501

BLOCK DIAGRAM

BACKLIGHT-ADJ

POWER SUPPLY CBA

IC3101

(MAIN MICRO CONTROLLER)

TX(+)

AD6

TX(-)

AE6

RX(+)

AC7

CN4052

KEY-IN146

REMOTE55

LED164

LIGHT73

CN3105

Q3101

LED DRIVE

BUFFER

Q3102

T3

V3

U3

U1

LED1

KEY-IN1

REMOTE

LIGHT-SENS

USB0(-)

USB0(+)

RX(-)

N22

M24

AC8

(MEMORY)

IC3103

USB1(+)

L23

SCL

SDA

6

5

AC2

AC1

STM-SCL

STM-SDA

USB1(-)

M22

IR SENSOR CBA UNIT

VGA-SCL

Y7

VGA-SDA

LCD-P-ON

W2

AD3

COMP-DET

HP-DET

L2

H6

P-ON-H2

RESET

PROTECT3

BACKLIGHT-SW

66

44

CN3601

RESET

Y2

AD5

P-ON-H2

STB-RESET

TU-SCL

Y15

BACKLIGHT-ADJ

33

55

77

CN3601

IC3601

T2

P7

W3

PROTECT3

BACKLIGHT-SW

BACKLIGHT-ADJ

TU-SDA

AA16

AXI

AE4

AXO

AD4

DIGITAL MAIN CBA UNIT

TX(+)

CN3706

TX(-)

RX(-)

RX(+)

ETHERNET

JACK

USB0(+)

CN3704

USB0(-)

USB JACK

USB1(+)

WIRELESS

CN3701

USB1(-)

LAN MODULE

VGA-SCL

9-1

LCD-P-ON

VGA-SDA

TO VIDEO/AUDIO

HP-DET

COMP-DET

BLOCK DIAGRAM

4

3

SCL

SDA

TU3001 (TUNER UNIT)

X3101

25MHz

OSC

PL14.22ABLS

2. Video/Audio Block Diagram

AUDIO SIGNAL

VIDEO SIGNAL

VGA-R-IN

VGA-B-IN

VGA-G-IN

VGA-VSYNC

VGA-HSYNC

IF-AGC

DIF-OUT1

DIF-OUT2

COM-VIDEO-Pr-IN

COM-VIDEO-Pb-IN

COM-VIDEO-Y/VIDEO-IN

TO DIGITAL

SIGNAL PROCESS

BLOCK DIAGRAM

AUDIO(L)-IN

AUDIO(R)-IN

SPDIF

HP(R)

HP(L)

AMP(L)-OUT

3

VGA-SCL

VGA-SDA

AMP(R)-OUT

Q3821

12

TO SYSTEM CONTROL

BLOCK DIAGRAM

HP-DET

LCD-P-ON

COMP-DET

P-ON+3.3V

1

2

Q3822

DIGITAL MAIN CBA UNIT

123

131415

JK3713

PC-RGB

-IN

6

7

DIF-OUT2

DIF-OUT1

(TUNER UNIT)

TU3001

12

5

IF-AGC

JK3701

COMPONENT

-Y/VIDEO-IN

COMPONENT

-Pb-IN

JK3706

COMPONENT

-Pr-IN

AUDIO(L)-IN

Q3709

AUDIO(R)-IN

BUFFER

DIGITAL

AUDIO-OUT

(COAXIAL)

JK3801

HEADPHONE

JACK

DRIVE

IC3803 (AUDIO AMP)

25

POWER

LIMIT

PWM

LOGIC

DRIVE

23

CN3801

DRIVE

18

2

1

SP(L)-

SP(L)+

SP3801

SPEAKER

L-CH

POWER

LIMIT

PWM

LOGIC

DRIVE

20

3

4

SP(R)-

SP(R)+

CONTROL LOGIC

SP3802

SPEAKER

R-CH

9-2

PL14.22ABLVA

3. Digital Signal Process Block Diagram

LCD PANEL

ASSEMBLY

LVDS-OCLK(-)

LVDS-OD2(+)

LVDS-OD3(-)

LVDS-OD3(+) 13

J2

H3

H4

LVDS-OCLK(+)

LVDS-ED0(-)

LVDS-ED0(+)

17

16

40393837363530

J3

H2

M5

M6

LVDS

TX

LVDS-ED1(-)

LVDS-ED1(+)

LVDS-ED2(-)

L6

N5

M4

LVDS-ED2(+)

LVDS-ED3(-)

LVDS-ED3(+) 29

J5

L5

K5

LVDS-ECLK(-)

LVDS-ECLK(+)

33

32

L7

M7

AUDIO SIGNAL

VIDEO SIGNAL

LVDS-OD0(-)

LVDS-OD0(+)

LVDS-OD1(-)

LVDS-OD1(+)

24232221201914

CN3906

L4

L3

K3

K4

LVDS-OD2(-)

J1

DATA(0-15)

ADDESS(0-14)

IC3401

(DDR3 SDRAM)

MMDQ(0-31)

DATA(16-31)

IC3402

(DDR3 SDRAM)

MMA(0-14)

ADDESS(0-14)

IC3102

(NAND FLASH MEMORY)

DATA(0-7)

DIGITAL MAIN CBA UNIT

MMCDAT(0-7)

VGA-HSYNC

IC3101 (DIGITAL SIGNAL PROCESS)

Y11

VGA-HSYNC

VGA-VSYNC

A/D

CONVERTER

VGA-VSYNC

AA12

AB13

AC13

AD13

COM-VIDEO-Y/VIDEO-IN

VGA-R-IN

VGA-G-IN

VGA-B-IN

DEMODULATOR

SW

AB10

AB11

AC11

AD11

AD9

DIF-OUT1

DIF-OUT2

COM-VIDEO-Pb-IN

COM-VIDEO-Pr-IN

TO VIDEO/AUDIO

/MPEG DECODER

IF-AGC

AB17

AA13

AE14

AC18

AE9

IF-AGC

AMP(L)-OUT

AMP(R)-OUT

AUDIO(L)-IN

BLOCK DIAGRAM

AUDIO I/F

AC14

AC17

AD17

AUDIO(R)-IN

HP(L)

HP(R)

F4

SPDIF

JK3717

AUDIO

ARC-OUT

F5

AE22

AC23

DATA0(+)

ARC

DATA0(-)

71494613

DIGITAL

SIGNAL

DECODER

AE23

AD23

DATA1(+)

DATA1(-)

PROCESS

AD24

DATA2(+)

DATA2(-)

HDMI-IN1

AE24

AD22

CLOCK(+)

CLOCK(-)

101216

W6

AC22

HDMI-DATA

HDMI-CLOCK

T7

15

HDMI

I/F

W23

DATA0(+)

DATA0(-)

79461

JK3715

HDMI SW

V23

W22

DATA1(+)

DATA1(-)

V22

DATA2(+)

V24

U23

DATA2(-)

CLOCK(+)

3

HDMI-IN2

Y25

Y24

HDMI-DATA

CLOCK(-)

101216

VIDEO

DECODER

V7

AA5

HDMI-CLOCK

15

JK3716

AB24

AA23

AC25

DATA0(+)

DATA0(-)

DATA1(+)

79461

AB25

DATA1(-)

Y23

DATA2(+)

DATA2(-)

HDMI-IN3

AA24

AC24

CLOCK(+)

CLOCK(-)

3

101216

R9

AD25

AE3

HDMI-DATA

HDMI-CLOCK

15

9-3

PL14.22ABLD

4. LED Backlight Drive Block Diagram

LCD PANEL

ASSEMBLY

VLED11

ILED12

VLED23

ILED24

VLED31

ILED32

CN1101

Q1103

Q1101

3

14

OVP

DRIVE

LOGIC

ISW

FAIL

DETECT

131511

DRIVE

LOGIC

CN1101

CN1301

Q1203

Q1201

3

14

OVP

DRIVELOGIC

ISW

FAIL

DETECT

131511

DRIVE

LOGIC

Q1301

3

14

OVP

DRIVE

LOGIC

ISW

FAIL

DETECT

Q1303

131511

DRIVE

LOGIC

IC1101

(LED BACKLIGHT DRIVER)

VIN

LDO

2

6

BACKLIGHT-ADJ

BACKLIGHT-SW

PROTECT3

TO

SYSTEM CONTROL

BLOCK DIAGRAM

IC1201

(LED BACKLIGHT DRIVER)

9-4

LDO

2

LDO

IC1301

6

(LED BACKLIGHT DRIVER)

2

6

POWER SUPPLY CBA

PL14.22ABLBD

5. Power Supply Block Diagram

AL+3.3V

P-ON+21V

AMP+13V

DIGITAL MAIN CBA UNIT

CN3601

15-18

20-23

P-ON+21V

AL+3.3V8 8

AMP+13V

20-23

15-18

NOTE:

The voltage for parts in hot circuit is measured using

hot GND as a common terminal.

CN501

AMP+13V

VIN

Q650

RESET

TO SYSTEM CONTROL

RESET

P-ON-H2

BLOCK DIAGRAM

POWER SUPPLY CBA

+3.3V REG.

Q703,Q705

9

4

5

SWITCHING

8

6

111210

T601

2

1

3

For continued protection against risk of fire,

replace only with same type 2.5A, 250V fuse.

CAUTION ! :

ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.

2.5A 250V

BRIDGE

D601-D604

LINE

L601

Q601

RECTIFIER

FILTER

7

IC602

RESET

Q654

14

ERROR

VOLTAGE DET

SWITCHING

Q602

IC601

SWITCHING

8

T1602

1

Q702

3 2

CONTROL

5

4

3 IS

Q701

T1601

5

OUT

Q653

Q691

1

ZCD

14

IC1602

(ISOLATOR)

2

FB

3 2

HOT COLD

11

131014

2

6

1

FB

ZCD

VCC

8

5

1

4

T1701

6

7

5

Q1704

3

SWITCHING

15

2

ERROR

IC1702

IC1701

SWITCHING

CONTROL

14

3 2

VOLTAGE DET

3 IS

OUT5VCC

6

SWITCHING

LINE

FILTER

L602

F602

2.5A/250V

B

CN601

HOT CIRCUIT. BE CAREFUL.

AC601

AC CORD

CAUTION !

Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.

If Main Fuse (F602) is blown , check to see that all components in the power supply

circuit are not defective before you connect the AC plug to the AC power supply.

Otherwise it may cause some components in the power supply circuit to fail.

2.5A 250V

W

Q1602

14

IC1601

(SWITCHING CONTROL)

7

SWITCHING

Q1601

11

SWITCHING

CONTROL

8

9-5

VCC

Q1701

11612

SW+15V

Q1702

Q1607

Q1604

PL14.22ABLP

[TYPE B]

1. System Control Block Diagram

KEY SWITCH

FUNCTION CBA UNIT

CN4001

KEY-IN122

CN4051

P-ON+5V

LIGHT

REMOTE

RS4051

SENSOR

D4051

POWER

CN4052

IC4051

SENSOR

IR SENSOR CBA UNIT

TO

POWER SUPPLY

P-ON-H2

CN501

P-ON-H2

18 6

CN3602

BLOCK DIAGRAM

RESET

20 4

TO

LED BACKLIGHT DRIVE

BACKLIGHT-SW

BACKLIGHT-ADJ

CN501

BACKLIGHT-SW

BACKLIGHT-ADJ

19 5

17 7

CN3602

BLOCK DIAGRAM

PROTECT3

21 3

POWER SUPPLY CBA

IC3101

(MAIN MICRO CONTROLLER)

KEY-IN146

REMOTE55

LED164

LIGHT73

CN3101

LED DRIVE

BUFFER

Q3010

Q3501, Q3502

120

128

100

130

LED1

LIGHT

KEY-IN1

REMOTE

USB(+)

USB(-)

123

124

(MEMORY)

IC3006

SCL

SDA

6

5

114

112

SPI-SCL

SPI-SDA

VGA-SCL

117

AMP-MUTE

VGA-SDA

636499

116

Q3105

AL+3.3V

COMP-DET

HP-DET

Q3106

133

P-ON-H2

RESET

IC3009,

Q3104

122

CPU-RESET

TU-SCL

TU-SDA

59

58

4

3

SCL

SDA

101

BACKLIGHT-SW

P-ON+3.3V

110

BACKLIGHT-ADJ

X3101

Q3103

XOUT

XIN

53

54

24MHz

OSC

104

PROTECT3

DIGITAL MAIN CBA UNIT

USB(-)

CN3009

USB(+)

USB JACK

VGA-SCL

9-6

AMP-MUTE

VGA-SDA

TO VIDEO/AUDIO

HP-DET

COMP-DET

BLOCK DIAGRAM

TU3901 (TUNER UNIT)

PL14.22BBLS

2. Video/Audio Block Diagram

AUDIO SIGNAL

VIDEO SIGNAL

VGA-R-IN

VGA-B-IN

VGA-G-IN

VGA-VSYNC

VGA-HSYNC

IF-AGC

DIF-OUT1

DIF-OUT2

COM-VIDEO-Pr-IN

COM-VIDEO-Pb-IN

COM-VIDEO-Y/VIDEO-IN

TO DIGITAL

SIGNAL PROCESS

BLOCK DIAGRAM

AUDIO(L)-IN

AUDIO(R)-IN

SPDIF

HP(R)

HP(L)

AMP(L)-OUT

3

VGA-SCL

VGA-SDA

AMP(R)-OUT

1

12

TO SYSTEM CONTROL

BLOCK DIAGRAM

HP-DET

AMP-MUTE

COMP-DET

Q3801

2

DIGITAL MAIN CBA UNIT

123

131415

JK3005

PC-RGB

-IN

6

7

DIF-OUT2

DIF-OUT1

(TUNER UNIT)

TU3901

12

5

IF-AGC

JK3702

COMPONENT

-Y/VIDEO-IN

COMPONENT

-Pb-IN

JK3701

COMPONENT

-Pr-IN

AUDIO(L)-IN

Q3701

AUDIO(R)-IN

BUFFER

DIGITAL

AUDIO-OUT

(COAXIAL)

3

7

6dB

(HEADPHONE AMP)

IC3851

2

8

JK3703

HEADPHONE

POWER

LIMIT

LOGIC

DRIVE

23

CN3801

DRIVE

18

2

1

SP(L)-

SP(L)+

SP3801

SPEAKER

L-CH

LIMIT

PWM

LOGIC

4

SP(R)+

DRIVE

20

3

SP(R)-

CONTROL LOGIC

SP3802

SPEAKER

R-CH

POWER

PWM

DRIVE

IC3801 (AUDIO AMP)

25

JACK

9-7

PL14.22BBLVA

3. Digital Signal Process Block Diagram

LCD PANEL

ASSEMBLY

RXO0(-)

RXO0(+)

RXO1(-)

RXO1(+)

RXO2(-)

RXO2(+)

RXOCLK(-)

RXOCLK(+)

RXO3(-)

RXO3(+)

19

17

16

14

13

AUDIO SIGNAL

RXE0(-)

RXE0(+)

4039383736

CN3013

RXE1(-)

RXE1(+)

RXE2(-)

RXE2(+) 35

RXE3(-)

RXE3(+)

30

29

RXECLK(-)

RXECLK(+)

2423222120

33

32

VIDEO SIGNAL

VGA-HSYNC

IC3101 (DIGITAL SIGNAL PROCESS)

14

A/D

CONVERTER

SW

VGA-VSYNC

201917161524222623

90

89

86

88

91

DEMODULATOR

/MPEG DECODER

IF-AGC

464735

495048

85

82

81

AUDIO I/F

344445

DIGITAL MAIN CBA UNIT

77

76

75

78

84

83

LVDS

TX

62

148

147

150

70

DIGITAL

SIGNAL

AUDIO

DECODER

149

152

72

697473

PROCESS

151

146

71

145

135

134

HDMI

I/F

HDMI SW

9

8

111013

7

6

12

137

136

156

155

214

VIDEO

DECODER

3

154

153

139

140

VGA-HSYNC

VGA-VSYNC

VGA-R-IN

COM-VIDEO-Y/VIDEO-IN

COM-VIDEO-Pb-IN

COM-VIDEO-Pr-IN

VGA-G-IN

VGA-B-IN

DIF-OUT1

DIF-OUT2

TO VIDEO/AUDIO

BLOCK DIAGRAM

IF-AGC

AMP(L)-OUT

AMP(R)-OUT

AUDIO(L)-IN

AUDIO(R)-IN

HP(L)

HP(R)

SPDIF

DATA0(+)

DATA0(-)

79461

JK3003

DATA1(+)

DATA1(-)

9-8

DATA2(+)

DATA2(-)

CLOCK(+)

CLOCK(-)

3

101216

HDMI-IN1

HDMI-DATA

HDMI-CLOCK

15

DATA0(+)

DATA0(-)

79461

JK3002

DATA1(+)

DATA1(-)

DATA2(+)

DATA2(-)

HDMI-IN2

CLOCK(+)

CLOCK(-)

3

101216

HDMI-DATA

HDMI-CLOCK

15

DATA0(+)

DATA0(-)

79461

JK3004

DATA1(+)

DATA1(-)

DATA2(+)

DATA2(-)

3

HDMI-IN3

PL14.22BBLD

CLOCK(+)

CLOCK(-)

HDMI-DATA

101216

HDMI-CLOCK

15

4. LED Backlight Drive Block Diagram

LCD PANEL

ASSEMBLY

VLED11

ILED12

VLED23

ILED24

VLED31

ILED32

CN1101

Q1103

Q1101

3

14

OVP

DRIVE

LOGIC

ISW

FAIL

DETECT

131511

DRIVE

LOGIC

CN1101

CN1301

Q1203

Q1201

3

14

OVP

DRIVELOGIC

ISW

FAIL

DETECT

131511

DRIVE

LOGIC

Q1301

3

14

OVP

DRIVE

LOGIC

ISW

FAIL

DETECT

Q1303

131511

DRIVE

LOGIC

IC1101

(LED BACKLIGHT DRIVER)

VIN

LDO

2

6

BACKLIGHT-ADJ

BACKLIGHT-SW

PROTECT3

TO

SYSTEM CONTROL

BLOCK DIAGRAM

IC1201

(LED BACKLIGHT DRIVER)

9-9

LDO

2

LDO

IC1301

6

(LED BACKLIGHT DRIVER)

2

6

POWER SUPPLY CBA

PL14.22BBLBD

5. Power Supply Block Diagram

AL+3.3V

P-ON+21V

AMP+13V

DIGITAL MAIN CBA UNIT

CN3602

6-9

1-4

P-ON+21V

AL+3.3V8 16

AMP+13V

20-23

15-18

CN501

NOTE:

The voltage for parts in hot circuit is measured using

hot GND as a common terminal.

9

2

3

4

T601

111210

1

AMP+13V

VIN

RESET

Q650

Q702

RESET

Q654

8

7

14

5

6

IC602

ERROR

VOLTAGE DET

3 2

Q701

Q653

TO SYSTEM CONTROL

RESET

P-ON-H2

BLOCK DIAGRAM

POWER SUPPLY CBA

Q691

For continued protection against risk of fire,

replace only with same type 2.5A, 250V fuse.

CAUTION ! :

ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.

SWITCHING

2.5A 250V

HOT CIRCUIT. BE CAREFUL.

BRIDGE

D601-D604

LINE

L601

LINE

L602

F602

2.5A/250V

B

CN601

Q601

RECTIFIER

FILTER

2.5A 250V

W

SWITCHINGSWITCHING

Q602

3 IS

IC601

CONTROL

8

5

T1602

1

4

SWITCHING

Q1602

14

IC1601

(SWITCHING CONTROL)

7

5

OUT

8

T1601

1

SWITCHING

CONTROL

6

1

ZCD

VCC

5

4

SWITCHING

Q1601

11

8

VCC

11

131014

2

FB

T1701

6

7

3

5

15

2

IC1702

14

ERROR

VOLTAGE DET

3 2

14

IC1602

(ISOLATOR)

3 2

HOT COLD

6

1

ZCD

Q1607

2

FB

IC1701

SWITCHING

Q1701

3 IS

CONTROL

Q1604

OUT5VCC

SWITCHING

Q1704

11612

SW+15V

Q1702

AC601

AC CORD

CAUTION !

Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.

If Main Fuse (F602) is blown , check to see that all components in the power supply

circuit are not defective before you connect the AC plug to the AC power supply.

Otherwise it may cause some components in the power supply circuit to fail.

9-10

PL14.22BBLP

SCHEMATIC DIAGRAMS / CBA AND TEST POINTS

Standard Notes

WARNING

Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.

Notes:

1. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared.

2. All resistance values are indicated in ohms (K = 10

3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.

4. All capacitance values are indicated in F (P = 10

5. All voltages are DC voltages unless otherwise specified.

6.

This schematic diagrams are masterized version that should cover the entire PL14.22 chassis models. Thus some parts in detail illustrated on this schematic diagrams may vary depend on the model within the PL14.22 chassis. Please refer to the parts lists for each models.

7. The Circuit Board layout illustrated on this service manual is the latest version for this chassis at the moment of making this service manual. Depend on the mass production date of each model, the actual layout of each Board may differ slightly from this version.

3

, M = 106).

-6

F).

10-1 FL14.22SC

LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON

2

3

1

5.0 5.0

Voltage

Indicates that the voltage is not consistent here.

Power on mode

(Unit: Volt)

1-D3

Distinction Area

Line Number (1 to 3 digits)

Examples:

1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3".

2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1".

: Indicates a test point with a jumper wire across a hole in the PCB. : Used to indicate a test point with a component lead on foil side. : Used to indicate a test point with no test pin. : Used to indicate a test point with a test pin.

THE FOLLOWING PAGES:

1. CAUTION:

CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME

TYPE_A,_V FUSE.

ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.

2. CAUTION:

Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F602) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

3. Note:

1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since the drawings were prepared.

2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual.

4. Voltage indications on the schematics are as shown below:

Plug the TV power cord into a standard AC outlet.:

5. How to read converged lines

6. Test Point Information

The reference number of parts on Schematic Diagrams/CBA can be retrieved by application search function.

3

AREA D3

2

1

ABCD

10-2 FL14.22SC

AREA B1

1-D3

1-B1

Power Supply 1 Schematic Diagram

4

3

2

1

AC601 AC CORD

CAUTION !

Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F602) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

HOT CIRCUIT. BE CAREFUL.

CN601 W

B

2.5A250V

C1607 1200P

R1609

5.6K

D1610 OPEN

C1604

2.2

R1607 220

R1608 51K

F602

2.5A/250V

R1601 750K

R1602 750K

R1604 750K

R1605 750K

R1645 68K

R1610 18K

R1606 120K

C1606 1000P

C1605 1200P

SA601 VARISTOR

C1615 OPEN

R1616 47K

R1621

1.8K

R1655 OPEN

L602 LINE FILTER

C604

R601

0.1

1.2M

/310V

/1/2W

BC1601 WIRE

BC1602 WIRE

R1624

0.033/5W

C1626 OPEN

C1613 220P /2KV

Q1602

R1617

R1612

750K

R1618

R1613

750K

R1619

R1614

750K

750K R1615

R1620

750K

IC1601 UCC28063DR

(SWITCHING CONTROL)

1.4 ZCDB

1

6.0 VSENSE

2

3.1 TSET

3

6.0 PHB

4

1.4 COMP

5

0

GND

6

1.7 VINAC CS

7

3.6 HVSEN

89

C1608 1000P

C1610 22P

TK7P60W

(SWITCHING)

R1630 OPEN

ZCDA

VREF

GDA

GND

VCC

GDB

PWMCNTL

R1625 47

R1629 OPEN

G

6.5

1.4

16

6.0

15

6.5

14

0

13

15.4

12

6.5

11

0

10

0

Q1601 TK7P60W

(SWITCHING)

150.3

6.5

C614 1 /310V

C1612

0.47 /310V

R1626 47

C1603

0.22

R1622 18K

C1601 8200P

G

0

150.2

D

S

0

D

S

L601 LINE FILTER

D1603 30PFB60

D1605 30PFB60

R1654

C1609

OPEN

22P

R1611 100

R1653 68

C1614 220P /2KV

D601 1N5406BH

D602 1N5406BH

T1602 TE2520A7001

18

R1623 12K

45

C1621 100 /400V

T1601 TE2520A7001

18

45

C1602

C1611

4.7

0.1 /50V

R618

0.22 /2W

R607

4.7K

R1704 22K

R1703

R1627 12K

D604 1N5406BH

D603 1N5406BH

R603 OPEN

C1703 220P

379.2 D

G

C606

S

0

220P

R617

/2KV

4.7K

D613A

D613

OPEN

1ZB36BB

R604

2.7K

1.1 157.5

C610

1.4

220P

C607 1000P

C608 150P

1.0

2.0

0.1 C1701 1000P

C1702

R1701

150P

OPEN

Q1604 2SC5344SY

(SWITCHING)

15.4 18.6

R1633

2.7K

R1657

2.7K

2.5A 250V

Q601 TK4P60DA

(SWITCHING)

2.2 C625 1000P

R605 270

IC601 FA5640N

SWITCHING CONTROL

VH

ZCD

FB

2

NU

IS

3

VCC

0

4

GND OUT

R613 OPEN

IC1701 FA5640N

SWITCHING CONTROL

ZCD

VH

2

NU

FB4.7K

3

VCC

IS

4

GND OUT

R1709 OPEN

R1656

4.7

16.1

R1634 47

D1608 C1618 TFZVTR16B

10/50V

CAUTION ! :

For continued protection against risk of fire, replace only with same type 2.5A, 250V fuse.

ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.

HOT COLD

D607

D611 OPEN

D609A CES520

R609 820K

81

7

6

5

D614

D1705A CES520

14.4

81

7

14.4

6

5.00

5

D1704 OPEN

R1637 180

R608 22

17.20.1

2.7

BC602 BEAD

R606 22K

D615 1SS400ST

R634 270

C611

0.1

C620 33/35VTFZVTR27B

R1714 22

R1712 180

R1707 820K

C1704

0.1

Q1607 2SA1576UBTLQ

(SWITCHING)

18.6 18.7

18.0

C602

0.1 /310V

R1639 10K

1N5406BH

D605 1N4005

D606 1N4005

R610

R624

15K

510K

R611

R625

15K

510K

R614

R626

15K

510K

R627 36K

R623

1.8K

C616 220 /35V

D617 0

C612 1000P

C621 4700P

2.5

C622 1000P

D1710 OPEN

R1702

2.7K

R1705 27K

Q602 TK3P50D

(SWITCHING)

17.7

R628 22K

1.9 IC604

SL431A-AT

0

SHUNT REGULATOR (SWITCHING)

C1708 33/400V

Q1704 TK5A65D

(SWITCHING)

C1710

R17181000P 22K

D1707A OPEN

R1711 10K

R1720 270

R1708

C1709

22K

220/10V

R1638 18K

R631

R630

560K

D664A RS1KJTD

D620 OPEN

D619A

D620A

RS1GJTD

DS

36.918.1

G

R635

R633

1.2K

D618 TFZVTR18B

D623 MM5Z5V6B

R620

C624

0.1

R629 47K

R1746 270K

269.6

D

G

4.6 S

0.1

R1719

0.12/2W

Q1702 2SA1576UBTLQ

(SW+15V)

15.5 15.4

14.8

R1710 22K

0

Q1701

0.7

KTC3875S

-Y-RTK/P

0

(SWITCHING)

D619 OPEN

R619

4.7

R632

1.2K

0

D1714 OPEN

BC1703 BEAD

C1706 470P /2KV

C665 680P /2KV

D664 OPEN

1.4 Q60347K KTC3875S

-Y-RTK/P

0

R1747 270K

D1707 1ZB36BB

C605 33/400V

C619 1000P/250V

1

2

3

4

5

D621 OPEN

6

D621A RS1GJTD

C615 47/50V

IC602 TLP785F

ERROR VOLTAGE DET

1.4 4

0

32

7 C1726 1500P /2KV

6 D1714A

RS1KJTD

5

3

2

IC1702 TLP785F

ERROR VOLTAGE DET

2.0 4

0

32

IC1602 TLP785F

(ISOLATOR)

0.1 4

0 0.7

32

C1707 1000P/250V

T601 POWER TRANS

T1701 POWER TRANS

C1711 OPEN

10

11

13

14

15

1

12

11

10

9

8

7

21.1

20.1

26.3

25.3

1.8

D656 OPEN

D656A RS1GJTD

R651 1

D658 OPEN

D653 SB3150BH

D655 SB3150BH

R655 180

20.1

2.5 D660

0

SL431A-AT

D710 SB3200BR

D711 SB3200BR

D712 SB3200BR

C725 2200P/1KV

D650 SB3200BR

C650 2200P/1KV

D657 MM5Z4V3B

C656

R656

1/50V

8.2K

C654 470/16V

R654 180

R657

3.9K R659 27K

R660

R658

C660

0.1

R738 330

25.3

(SWITCHING)

3.9K

2.7K

D661 1SS400ST

R661

3.3K

Q653 KTC3875S

-Y-RTK/P

(SWITCHING)

D713 OPEN

D1711 TFZVTR27B

R740

C721 51K

20K

0.1

2.5 D704

0

SL431A-AT

C691

0.01

0.7

Q691 KTC3875S

-Y-RTK/P

1.4

0.7

D663 1SS400ST

NOTE:

The voltage for parts in hot circuit is measured using hot GND as a common terminal.

POWER SUPPLY CBA

C652

D652

C651 470/25V

R652 10K

C655 470/16V 1ZB20BB

R675 68K

R674 0

D713A OPEN

C722

0.1

R667

8.2K

0

R741

3.9K

R739 15K

R692 330

C692 33/35V

470/25V

0.7

R662 47K

D654A C657 OPEN

D654

R756

1.5

R752 OPEN

R749 3.3K 270

0.7

R668 47K

R743

R744

9.1K

R745

3.3K

R693 47K

R653 22K

0

D662 1SS400ST

R691

2.2K

D652A

OPEN

0

0 (RESET)

0

Q654 KTC3875S

0

-Y-RTK/P (RESET)

R663 OPEN

470/16V

Q705 2SA1201-Y

(+3.3V REG.)

12.9

3.3

12.3

R751

R750

270

R669 10K

C723 470/63V

3.3 Q650

KTC3875S

-Y-RTK/P

Q702 KTC3875S

-Y-RTK/P

(SWITCHING)

0

Q701 KTC3875S

-Y-RTK/P

0

(SWITCHING)

0.6

0

3.3 Q703

KTC3875S

3.9

-Y-RTK/P

(SWITCHING)

C729

0.1

3.9

2.5

D715

0

SL431A-AT

C724 470/63V

R703 10K

R704 47K

R702

C701

47K

OPEN

R748

R753 100

R755 0

R754 10K

C726

C1004

470/63V 1/100V

R701 10K

C637 OPEN

12.9

C638 OPEN

12.9

21.2

C639 OPEN

21.2

C728 100/10V

D716 TFZVTR4.7B

CONTINUE POWER SUPPLY 2

BACKLIGHT-SW BACKLIGHT-ADJ PROTECT3 AMP+13V

TO DIGITAL MAIN CBA UNIT CN3601

CN501

or CN3602

1NU 2 PROTECT1(NU)

3.3 3 PROTECT3

3.3 4 RESET

3.3 5 BACKLIGHT-SW

3.1

P-ON-H26

3.3 7 BACKLIGHT-ADJ

3.3 8 AL+3.3V

0

9 GND

0

10 GND

0

11 GND

0

12 GND

0

13 GND

0

14 GND 15 AMP+13V 16 AMP+13V 17 AMP+13V 18 AMP+13V

0

19 GND 20 P-ON+21V 21 P-ON+21V 22 P-ON+21V 23 P-ON+21V

CONTINUE POWER SUPPLY 2

VIN

A FBCDE G

10-3

PL14.22SCP1

Power Supply 2 Schematic Diagram

C1316 1/100V

LDO

LOGIC DRIVE

FAIL DETECT

LOGIC

L1301 100uH

DRIVE

C1317 100/100V

ISW

GND

OSC

4

3

R1322 OPEN

D1303 1SS400ST

R1301 75K

C1320 OPEN

D1304 TFZVTR27B

D1305 TFZVTR27B

R1323

5.6K

R1324

5.6K

R1303

R1302

20K

R1309 100K

R1311 24K

R1312

2.2K

R1325 360K

R1326 240K

R1327 20K

R1308 10K

C1303 100/63V

C1304 OPEN

R1333 OPEN

R1310 36K

C1306

0.22

C1307

0.047

C1302 1/100V

C1314 1/100V

C1305 1

C1301 1/100V

C1315 OPEN

IC1301 HA7223PE

LED BACKLIGHT DRIVER

5.0 1

3.0 2

2.3

OVP

3

5.6

ULVS

0.3 5

3.0 611

0.2

NU

7

2.1

NU

8

R1306

R1307

10K

100K

TO LCD PANEL

CN1301

ASSEMBLY

70.9 1 VLED3

0.7 2 ILED3

C1116 1/100V

LOGIC DRIVE

FAIL DETECT

LOGIC

DRIVE

L1101 100uH

OSC

C1117 100/100V

11.4

16VCC

0

ISW

15

3.5

14

11.4

134

0

GND

12

0.7

1.3

10

1.2

9

R1120 120

C1111 OPEN

R1119

D1101 SB2150BD

D1101A OPEN

C1110

0.22

41.6

R1118 200

C1109 1000P

R1105 75

R1104 75

0

R1128 1K

R1121 51

C1113 2200P

C1112 1

D

S

R1115

0.12/1W

L1102 BEAD

Q1101 AP05N20GH-HF

(SWITCHING)

G

3.6 C1108 560P

R1116 OPEN

R1117 OPEN

G

11.4

D1106 OPEN

0.7

D

Q1103 AP18T10AGH-HF

(SWITCHING)

S

0.7

R1129

0.62 R1130

0.56 R1131

0.56 R113262K

0

D1102 OPEN

R1113 10

GP001 OPEN

GP002 OPEN

GP003 OPEN

CN1101

70.9

0.7

70.9

0.7

TO LCD PANEL ASSEMBLY

1 VLED1 2 ILED1 3 VLED2 4 ILED2

CONTINUE POWER SUPPLY 1

BACKLIGHT-SW BACKLIGHT-ADJ PROTECT3 AMP+13V SPWM1 SPWM2

C1103

R1125 360K

R1126 240K

R1127 20K

C1104 OPEN

R1133 OPEN

R1108 10K

100/63V

D1301 SB2150BD

D1301A OPEN

11.4

16VCC

0

15

3.5

14

11.4

134

0

12

0.7 R1320

C1310

120

C1311 OPEN

R1319 62K

0.22

1.3

10

1.2

9

R1318 200

C1309 1000P

R1305 75

R1304 75

41.6

C1313 2200P

0

R1321 51

L1302 BEAD

Q1301

D

AP05N20GH-HF (SWITCHING)

G

3.6

S

R1315

0.12/1W

R1328 1K

11.4

C1312

D1306

1

OPEN

C1308 560P

R1316 OPEN

R1317 OPEN

G

D

S

0.7

R1329

0.62 R1330

0.56 R1331

0.56 R1332

0

D1302 OPEN

R1313 10

Q1303 AP18T10AGH-HF

(SWITCHING)

R1122 OPEN

D1103 1SS400ST

R1101 75K

R1102 20K

C1120 OPEN

D1104 TFZVTR27B

D1105 TFZVTR27B

R1123

5.6K

R1124

5.6K

R1103 20K

R1109 100K

R1111 24K

R1112

2.2K

R1110 36K

JS1135 OPEN

C1105 1

C1106

0.22

C1107

0.047

C1102

C1101

1/100V

C1114

C1115

1/100V

OPEN

IC1101 HA7223PE

LED BACKLIGHT DRIVER

5.0 1

LDO

3.0 2

2.3

OVP

3

5.6

ULVS

0.3 5

3.0 611

0.2

NU

7

2.1

NU

8

R1107

R1106

100K

10K

2

1

R1425 OPEN

R1426 OPEN

R1427 OPEN

R1433 OPEN

C1404 OPEN

R1408 OPEN

C1403 OPEN

R1410 OPEN

JS1435 OPEN

C1405 OPEN

C1406 OPEN

C1407 OPEN

R1401 OPEN

D1403 OPEN

R1422 OPEN

R1402 OPEN

C1420 OPEN

D1404 OPEN

D1405 OPEN

R1423 OPEN

R1424 OPEN

R1403 OPEN

R1409 OPEN

R1411 OPEN

R1412 OPEN

POWER SUPPLY CBA

C1416 OPEN

LDO

LOGIC DRIVE

FAIL DETECT

LOGIC

L1401 OPEN

DRIVE

C1417 OPEN

ISW

GND

OSC

16VCC

15

14

134

12

R1420 OPEN

10

C1411 OPEN

9

R1419 OPEN

C1402

C1401

OPEN

C1415

C1414

OPEN

IC1401 OPEN

1

2

3

OVP

ULVS

5

611

7

NU

8

NU

R1407

R1406

OPEN

D1401 OPEN

D1401A OPEN

C1410 OPEN

R1418 OPEN

C1409 OPEN

R1405 OPEN

R1404 OPEN

R1421 OPEN

C1413 OPEN

L1402 OPEN

D

G

S

R1415 OPEN

R1428 OPEN

C1412 OPEN

Q1401 OPEN

C1408 OPEN

R1416 OPEN

R1417 OPEN

D1406 OPEN

CONTINUE POWER SUPPLY 1

VIN

C1216 1/100V

LOGIC DRIVE

FAIL DETECT

LOGIC

DRIVE

L1201 100uH

OSC

C1217 100/100V

11.4

16VCC

0

15

ISW

3.5

14

11.4

134

0

12

GND

0.7

1.3

10

1.2

9

R1220 120

C1211 OPEN

R1219 62K

D1201 SB2150BD

D1201A OPEN

C1210

0.22

41.6

R1218 200

C1209 1000P

R1205 75

R1204 75

0

R1228 1K

R1221 51

C1213 2200P

C1212 1

D

S

R1215

0.12/1W

L1202 BEAD

Q1201 AP05N20GH-HF

(SWITCHING)

G

3.6

G

11.4

D1206 OPEN

C1208 560P

R1216 OPEN

R1217 OPEN

0.7

D

Q1203 AP18T10AGH-HF

(SWITCHING)

S

0.7

R1229

0.62 R1230

0.56 R1231

0.56 R1232

0

D1202 OPEN

R1213 10

CN1401

(NO CONNECTION)

1 VLED4 2 ILED4

C1201

R1210 36K

C1206

0.22

JS1235 OPEN

C1205 1

C1207

0.047

C1202

1/100V

C1214

C1215

1/100V

OPEN

IC1201 HA7223PE

LED BACKLIGHT DRIVER

5.0 1

LDO

3.0 2

2.3 3

OVP

5.6

ULVS

0.3 5

3.0 611

0.2 7

NU

2.1 8

NU

R1206

R1207

10K

100K

R1225 360K

R1226 240K

R1227 20K

R1233 OPEN

C1204 OPEN

R1208 10K

C1203 100/63V

D1203 1SS400ST

D1402 OPEN

R1413 OPEN

D

Q1403

G

OPEN

S

R1429 OPEN

R1430 OPEN

R1431 OPEN

R1432 OPEN

R1201 75K

R1222 OPEN

R1202 20K

C1220 OPEN

D1204 TFZVTR27B

D1205 TFZVTR27B

R1223

5.6K

R1224

5.6K

R1203 20K

R1209 100K

R1211 24K

R1212

2.2K

HLKJIM

10-4

PL14.22SCP2

Digital Main 1 Schematic Diagram [TYPE A]

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.

CN3905

1LCD+12V 2LCD+12V 3LCD+12V 4LCD+12V 5GND 6GND 7GND 8PANEL-WP

9LVDS-SEL 10NU 11GND 12LVDS-OD0(-) 13LVDS-OD0(+) 14GND 15LVDS-OD1(-) 16LVDS-OD1(+) 17GND 18LVDS-OD2(-) 19LVDS-OD2(+) 20GND 21LVDS-OCLK(-) 22LVDS-OCLK(+) 23GND 24LVDS-OD3(-) 25LVDS-OD3(+) 26GND 27BIST 28PANEL-SCL 29PANEL-SDA 30GND

LVDS-OD4(+) LVDS-OD4(-) LVDS-OD3(+)

LVDS-OD3(-) LVDS-OCLK(+) LVDS-OCLK(-)

LVDS-OD2(+)

LVDS-OD2(-)

LVDS-OD1(+)

LVDS-OD1(-)

LVDS-OD0(+)

LVDS-OD0(-)

LVDS-ED4(+)

LVDS-ED4(-)

LVDS-ED3(+)

LVDS-ED3(-) LVDS-ECLK(+) LVDS-ECLK(-)

LVDS-ED2(+)

LVDS-ED2(-)

LVDS-ED1(+)

LVDS-ED1(-)

LVDS-ED0(+)

LVDS-ED0(-)

CN3901 30LCD+12V

29LCD+12V 28LCD+12V 27LCD+12V 26GND 25GND 24GND 23PANEL-WP 22LVDS-SEL 21NU 20GND 19LVDS-OD0(-) 18LVDS-OD0(+) 17GND 16LVDS-OD1(-) 15LVDS-OD1(+) 14GND 13LVDS-OD2(-) 12LVDS-OD2(+) 11GND 10LVDS-OCLK(-)

9LVDS-OCLK(+) 8GND 7LVDS-OD3(-) 6LVDS-OD3(+) 5GND 4NU 3PANEL-SCL 2PANEL-SDA 1GND

OPENR3906 OPENR3904

R3910 OPEN

R3909 OPEN

R3907 OPEN

R3908 OPEN

10PC3916

10PC3903

10PC3904

4

3

2

1

(NO CONNECTION)

CONTINUE DIGITAL 2

(NO CONNECTION)

CONTINUE DIGITAL 7

BACKLIGHT-ADJ

10PC3905

10PC3908

10PC3906

10PC3911

10PC3912

10PC3907

OPENC3914

10PC3913

R3932 OPEN

R3934 OPEN

R3931

R3933

C3947

OPEN

Q3901 OPEN

OPEN

R3913 OPEN

R3914 OPEN

R3915 OPEN

R3935 OPEN

R3924 OPEN

*1

IC3101(1/7) MN2WS0270HA DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

L3

L4 J6 K6 J5 K5 L7 M7

L6 M4 N5 M5 11 LVDS-OD4(-) M6

K7 NU 8 LVDS-OD5(+)

OPENC3915

J7 NU

N2 NU P2 NU P7 BACKLIGHT-ADJ

R3901 10K

LVDS TX

TO DIGITAL MAIN 6 IC3101(5/7)

K3

K4

J1

J2

J3

H2L5

H3

H4

G3

F3

F1

F2

P1NU

R6TP

R3POL

P3CPV

N3OE

R5OE2

P4STV

OPENC3927

10PC3917

10PC3928

10PC3919

10PC3918

10PC3922

10PC3920

10PC3923

10PC3921

10PC3924

10PC3925

OPENC3926

OPENR3974 OPENR3975 OPENR3976 OPENR3977 OPENR3978 OPENR3979

DIGITAL MAIN CBA UNIT

OPEN

OPENR3928

OPENR3884

C3948 OPEN

OPENR3882

OPENR3883

OPENR3881

OPENR3880

OPENC3998

OPENC3942

OPENC3941

OPENC3940

OPENC3938

OPENC3939

R3925 OPEN

R3916 10K

CONTINUE DIGITAL 2

LCD+12V/+21V

CONTINUE DIGITAL 7

P-ON+21V P-ON+3.3V

CN3904

(NO CONNECTION)

30 LCD+21V 29 LCD+21V 28 GND 27 VCOM 26 PWR-CTRL 25 P-ON+3.3V 24 GND 23 LVDS-OD0(-) 22 LVDS-OD0(+) 21 LVDS-OD1(-) 20 LVDS-OD1(+) 19 LVDS-OD2(-) 18 LVDS-OD2(+) 17 GND 16 LVDS-OCLK(-) 15 LVDS-OCLK(+) 14 GND 13 LVDS-OD3(-) 12 LVDS-OD3(+) 11 LVDS-OD4(-) 10 LVDS-OD4(+)

9 LVDS-OD5(-) 8 LVDS-OD5(+) 7 GND 6TP 5 POL 4 CPV 3 OE1 2 OE2 1 STV

CN3903

(NO CONNECTION)

31 LCD+21V 30 LCD+21V 29 LCD+21V 28 GND 27 VCOM 26 PWR-CTRL 25 P-ON+3.3V 24 GND 23 LVDS-OD0(-) 22 LVDS-OD0(+) 21 LVDS-OD1(-) 20 LVDS-OD1(+) 19 LVDS-OD2(-) 18 LVDS-OD2(+) 17 GND 16 LVDS-OCLK(-) 15 LVDS-OCLK(+) 14 GND 13 LVDS-OD3(-) 12 LVDS-OD3(+)

10 LVDS-OD4(+)

9 LVDS-OD5(-)

7 GND 6TP 5 POL 4 CPV 3OE 2 OE2 1 STV

CONTINUE DIGITAL 4

VCOM-PWM

CONTINUE DIGITAL 2

VCOM-DC VCOM-PWM LCD-P-ON PANEL-WP PANEL-SCL PANEL-SDA

CN3907

(NO CONNECTION)

1 GND 2 PANEL-WP 3 PANEL-SCL 4 PANEL-SDA

AB D

C

10-5

FE

PL14.22ASCD1

Digital Main 2 Schematic Diagram [TYPE A]

CONTINUE DIGITAL 7

P-ON+21V

P-ON+3.3V

CONTINUE DIGITAL 1

LCD+12V/+21V

4

3

2

1

TO LCD PANEL ASSEMBLY

CN3906 1LCD+12V

2LCD+12V 3LCD+12V 4LCD+12V 5NU 6GND 7GND 8GND

9GND 10GND 11LVDS-OD4(+) 12LVDS-OD4(-) 13LVDS-OD3(+) 14LVDS-OD3(-) 15GND 16LVDS-OCLK(+) 17LVDS-OCLK(-) 18GND 19LVDS-OD2(+) 20LVDS-OD2(-) 21LVDS-OD1(+) 22LVDS-OD1(-) 23LVDS-OD0(+) 24LVDS-OD0(-) 25GND 26GND 27LVDS-ED4(+) 28LVDS-ED4(-) 29LVDS-ED3(+) 30LVDS-ED3(-) 31GND 32LVDS-ECLK(+) 33LVDS-ECLK(-) 34GND 35LVDS-ED2(+) 36LVDS-ED2(-) 37LVDS-ED1(+) 38LVDS-ED1(-) 39LVDS-ED0(+) 40LVDS-ED0(-) 41GND 42NU 43NU 44NU 45VCOM 46LCD-P-ON 47/SCL 48/SDA 49PANEL-SDA 50PANEL-SCL 51PANEL-WP

C3992 1000P

OPENR3989 OPENR3988

OPENR3987 OPENR3986

OPENR3866

OPENR3982

C3991

4.7

R3920 0

R3919 0

R3990 0

OPENR3981 OPENR3980 0R3943 0R3921

OPENR3985 OPENR3984

OPENR3867 OPENR3922

OPENR3869 OPENR3926 OPENR3923 OPENR3902

0R3948 0R3947 OPENR3983 OPENR3918 OPENR3917

C3902 OPEN

R3941 OPEN

R3896 OPEN

R3940 OPEN

C3901

4.7

R3952 OPEN

D3906 OPEN

R3550

6.8K

C3946

0.047

C3951 OPEN

C3950 1500P

C3955

R3936100P 24K

C3959

R3911

R3912 C3952 OPEN

OPEN

D3902 1SS400

OPENR3900 OPENR3903 OPENR3905

R3937

C3958

4.7

R3938 33K

R39393.3K

6.8K

OPEN

C3909 OPEN

D3905 OPEN

IC3901 MP1472GJC452Z (+12V REG.)

1

SS

2

EN

3

COMP

45

FB GND

D3901 OPEN 4.7

C3910 OPEN

BST

IN

SW

C3954

4.7

8

7

6

C3956

4.7

C3949

0.1

L3901 22uH

C3953

C3945

0.1

C3944 OPEN

C3943

4.7

R3897 OPEN

R3895 OPEN

R3898 OPEN

C3997 OPEN

C3996 OPEN

R3899 OPEN

R3891 OPEN

Q3904 OPEN

R3942 OPEN

Q3905 OPEN

1

2

36

45

8

7

CONTINUE DIGITAL 6

P-ON-H2

CONTINUE DIGITAL 1

LVDS-OD4(+) LVDS-OD4(-) LVDS-OD3(+) LVDS-OD3(-) LVDS-OCLK(+) LVDS-OCLK(-) LVDS-OD2(+) LVDS-OD2(-) LVDS-OD1(+) LVDS-OD1(-) LVDS-OD0(+) LVDS-OD0(-) LVDS-ED4(+) LVDS-ED4(-) LVDS-ED3(+) LVDS-ED3(-) LVDS-ECLK(+) LVDS-ECLK(-) LVDS-ED2(+) LVDS-ED2(-) LVDS-ED1(+) LVDS-ED1(-) LVDS-ED0(+) LVDS-ED0(-)

CONTINUE DIGITAL 1

VCOM-DC VCOM-PWM LCD-P-ON PANEL-WP PANEL-SCL PANEL-SDA

CONTINUE DIGITAL 8

PROTECT3

H

10-6

J

DIGITAL MAIN CBA UNIT

LIKG

PL14.22ASCD2

Digital Main 3 Schematic Diagram [TYPE A]

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.

*1

IC3101(2/7) MN2WS0270HA

MAIN MICRO CONTROLLER

4

3

2

1

/DIGITAL SIGNAL PROCESS

DDRPWRON

MMVREF0 MMVREF1 MMVREF2

MMDQ0 MMDQ1 MMDQ2 MMDQ3 MMDQ4 MMDQ5 MMDQ6 MMDQ7 MMDQ8

MMDQ9 MMDQ10 MMDQ11 MMDQ12 MMDQ13 MMDQ14 MMDQ15 MMDQ16 MMDQ17 MMDQ18 MMDQ19 MMDQ20 MMDQ21 MMDQ22 MMDQ23 MMDQ24 MMDQ25 MMDQ26 MMDQ27 MMDQ28 MMDQ29 MMDQ30 MMDQ31

MMDQS1

MMXDQS1

MMDQS0

MMXDQS0

MMDQS3

MMXDQS3

MMDQS2

MMXDQS2

MMDM1

MMDM0

MMDM3

MMDM2

MMA2 MMA6 MMA8

MMA14

MMA9 MMA11 MMA13

MMA7

MMA4

MMA5

MMA1 MMA12 MMBA1 MMA10

MMA3

MMA0

MMBA2 MMBA0 MMXWE

MMXCAS

MMCK MMXCK

MMXCS1 MMXCS0

MEMORY I/F

TO DIGITAL MAIN 6 IC3101(5/7)

MMODT0 MMODT1 MMCKE0 MMCKE1

MMXRAS

MMXRESET

DDR3VOUT

MMZQ

NU NU

D3

D16

D6

D7 E6 B5 C5 C3 B1 C2 C1 C8 D8 C7 B7 C4 A3 B3

A2 D19 C18 B18 C17 B14 A14 C13 B13 B17 A17 D15 C15 B12 A12 D11 C11

B4

A4

A6

C6 D17 C16 B15 C14

C9

B2 C12 C19

G11

E8

G8

E7 E19 F18 E18 E17 D18 F17 F16 E16 D10 E10

D9

G9

G16 E15 D14 E14 B10

B9 D12 E11 F11 F12 F10 G10 F14 F19

D1

D4

G7 G12

10KR3433

R3405 56x4

R3406 56x4

R3407 56x4

R3408 56x4

R3409 56x4

56R3418 56R3417 56R3416 56R3415 56R3414 56R3413 56R3412

1C3405 240R3420

MMDQ0 MMDQ1 MMDQ2 MMDQ3 MMDQ4 MMDQ5 MMDQ6 MMDQ7 MMDQ8

MMDQ9 MMDQ10 MMDQ11 MMDQ12 MMDQ13 MMDQ14 MMDQ15 MMDQ16 MMDQ17 MMDQ18 MMDQ19 MMDQ20 MMDQ21 MMDQ22 MMDQ23 MMDQ24 MMDQ25 MMDQ26 MMDQ27 MMDQ28 MMDQ29 MMDQ30 MMDQ31

MMA2 MMA6 MMA8

MMA14

MMA9 MMA11 MMA13

MMA7

MMA4

MMA5

MMA1 MMA12

MMA10

MMA3

MMA0

R3419 10K

C3407 OPEN

0.1C3409

270R3422

0.1C3410

270R3424

270R3410

0.1C3406

DIGITAL MAIN CBA UNIT

270R3421 270R3423 270R3411

MMA14 MMA13 MMA12 MMA11 MMA10 MMA9 MMA8 MMA7 MMA6 MMA5 MMA4 MMA3 MMA2 MMA1 MMA0

MMDQ11 MMDQ14 MMDQ10 MMDQ12 MMDQ8 MMDQ15 MMDQ9 MMDQ13 MMDQ6 MMDQ2 MMDQ7 MMDQ3 MMDQ4 MMDQ1 MMDQ5 MMDQ0

IC3401 K4B1G1646G-BCK0 (DDR3 SDRAM)

CK J7

NU J1 NU J9

NU L9

B2VDD1 D9VDD2 G7VDD3 K2VDD4 K8VDD5 N1VDD6 N9VDD7 R1VDD8 R9VDD9 A1VDDQ1 A8VDDQ2 C1VDDQ3 C9VDDQ4 D2VDDQ5 E9VDDQ6 F1VDDQ7 H2VDDQ8 H9VDDQ9

M8VREFCA

H1VREFDQ

A9VSS1 B3VSS2 E1VSS3 G8VSS4 J2VSS5 J8VSS6 M1VSS7 M9VSS8 P1VSS9 P9VSS10 T1VSS11 T9VSS12 B1VSSQ1 B9VSSQ2 D1VSSQ3 D8VSSQ4 E2VSSQ5 E8VSSQ6 F9VSSQ7 G1VSSQ8 G9VSSQ9

K7CK# K9CKE

L1NU

R3425 270

R3426 270

R3427 220

C3411 10

C3408 1

C3415

0.1

C3419

0.1

R3403 OPEN

R3404 OPEN

C3431 10

C3412

0.1

C3416

0.1

C3429

0.1

C3403 OPEN

C3404 OPEN

C3413

0.1

C3417

0.1

C3414

0.1

C3418

0.1

MMA14 MMA13 MMA12 MMA11 MMA10 MMA9 MMA8 MMA7 MMA6 MMA5 MMA4 MMA3 MMA2 MMA1 MMA0

MMDQ19 MMDQ22 MMDQ18 MMDQ20 MMDQ16 MMDQ23 MMDQ17 MMDQ21 MMDQ30 MMDQ26 MMDQ31 MMDQ27 MMDQ28 MMDQ25 MMDQ29 MMDQ24

NU

M7

A14T7 A13T3 A12/BC#N7 A11R7 A10/APL7 A9R3 A8T8 A7R2 A6R8 A5P2 A4P8 A3N2 A2P3 A1P7 A0N3

C7 DQSU B7 DQSU# F3 DQSL G3 DQSL# D3 DMU E7 DML

DQU7A3 DQU6B8 DQU5A2 DQU4A7 DQU3C2 DQU2C8 DQU1C3 DQU0D7 DQL7H7 DQL6G2 DQL5H8 DQL4H3 DQL3F8

F2

DQL2 DQL1F7 DQL0E3

L2 CS# K3 CAS# K1 ODT J3 RAS# L3 WE# T2 RESET# T2 RESET# L8 ZQ

R3428 240

BA2M3 BA1N8 BA0M2

R3432 240

IC3402 K4B2G1646Q-BCMA (DDR3 SDRAM)

NU

M7

A14T7 A13T3 A12/BC#N7 A11R7 A10/APL7 A9R3 A8T8 A7R2 A6R8 A5P2 A4P8 A3N2 A2P3 A1P7 A0N3

C7 DQSU B7 DQSU# F3 DQSL G3 DQSL# D3 DMU E7 DML

DQU7A3 DQU6B8 DQU5A2 DQU4A7 DQU3C2 DQU2C8 DQU1C3 DQU0D7 DQL7H7 DQL6G2 DQL5H8 DQL4H3 DQL3F8 DQL2F2 DQL1F7 DQL0E3

L2 CS# K3 CAS# K1 ODT J3 RAS# L3 WE#

L8 ZQ

M3

BA2 BA1N8 BA0M2

CK J7

NU J1 NU J9

NU L9

B2VDD1 D9VDD2 G7VDD3 K2VDD4 K8VDD5 N1VDD6 N9VDD7 R1VDD8 R9VDD9 A1VDDQ1 A8VDDQ2 C1VDDQ3 C9VDDQ4 D2VDDQ5 E9VDDQ6 F1VDDQ7 H2VDDQ8 H9VDDQ9

M8VREFCA

H1VREFDQ

A9VSS1 B3VSS2 E1VSS3 G8VSS4 J2VSS5 J8VSS6 M1VSS7 M9VSS8 P1VSS9 P9VSS10 T1VSS11 T9VSS12 B1VSSQ1 B9VSSQ2 D1VSSQ3 D8VSSQ4 E2VSSQ5 E8VSSQ6 F9VSSQ7 G1VSSQ8 G9VSSQ9

K7CK# K9CKE

L1NU

R3429 270

R3430 270

R3431 220

C3420 10

C3421

0.1

C3425

0.1

C3428

0.1

R3401 OPEN

R3402 OPEN

C3432 10

C3422

0.1

C3426

0.1

C3430

0.1

C3401 OPEN

C3402 OPEN

C3423

0.1

C3427

0.1

C3424

0.1

CONTINUE DIGITAL 7

AL+3.3VT5 VCC+1.5V

M

N

O

10-7

P

Q

R

PL14.22ASCD3

Digital Main 4 Schematic Diagram [TYPE A]

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.

C3128

4

3

2

CONTINUE DIGITAL 1

VCOM-PWM

CONTINUE DIGITAL 6

COMP-DET

HP-DET

CONTINUE DIGITAL 7

P-ON+3.3V

P-ON+5V AL+3.3V

(NO CONNECTION)

CONTINUE DIGITAL 8

10GND

STB-RESET

STMTIME1

CN3104

9NU 8EJTCK 7JTDI 6JTDO 5JTMS 4TRSTN 3EVTRG 2XRST 1AL+3.3V

R3130 OPEN

R3126 OPEN

R3136 10K

R3113 10K

R3129 100

R3111 10K

R3208 OPEN

R3135 OPEN

15P

C3124 12P

10KR3198 OPENR3125

R3210 OPEN

1

X3101 25MHz

R3170 150

R3112 100

OPENR3127

1KR3224 OPENR3115

OPENR3116 1KR3118 OPENR3122

*1

IC3101(3/7) MN2WS0270HA

DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

AE4 AXI

R3169 OPEN

AD4 AXO

P6 VCOM-PWM G6 NU H6 COMP-DET G4 NU M3 NU

L2 HP-DET D20 NU A20 NU W20 NU V20 NU Y22 NU

AA22 NU AB23 NU

W21 NU U20 NU V21 NU Y21 NU U19 NU W19 NU V19 NU

AB22 NU

U21 NU

AA7 NU

U9 NU AD8 NU AB7 NU

Y8 NU L21 NU AC5 NU

E24 NU G21 NU E23 NU D25 NU C25 NU D24 NU J19 NU H19 NU L20 NU J23 NU L19 NU N20 NU K19 NU N21 NU M20 NU M19 NU J20 NU P20 NU K21 NU N19 NU P19 NU M21 NU F25 NU Y19NU H20 NU F23 NU F24 NU F22 NU H21 NU K20 NU

MEMORY I/F

TO DIGITAL MAIN 6 IC3104(5/7)

MMCDAT0

B22 A22MMCDAT1 D21MMCDAT2 C21MMCDAT3 B21MMCDAT4 E20MMCDAT5 B20MMCDAT6 C20MMCDAT7

D22NANDRYBY B23NFALE C23NFCLE A23XNFCE A24XNFWE B24XNFWP E21XNFRE C22NU F20NU J24NU J22NU G24NU G23NU H23NU G22NU H22NU K22NU J25NU P22NU P25NU R20NU T21NU R22NU R21NU T20NU T19NU R19NU P24NU P21NU

AB18NU

Y18NU Y17NU W17NU W15NU

AA17NU

W18NU

AC19NU

Y16NU

AD19NU

W16NU

Y20NU AB19NU AE20NU AB20NU AA18NU AD20NU AA21NU

AA19NU AA20NU AC20NU

MMCDAT0 MMCDAT1 MMCDAT2 MMCDAT3 MMCDAT4 MMCDAT5 MMCDAT6 MMCDAT7

10KR3132

10KR3121

10KR3173

10KR3124

10KR3128

R3205 22 R3201 75 R3202 75 R3203 75 R3190 75 R3189 75 R3204 75

10KR3123

C3125

C3126

0.1

IC3102 H27U1G8F2BTR-BC

(NAND FLASH MEMORY)

1

NU

2

NU

3

NU

4

NU

5

NU

6

NU

7

R/B

8

RE

9

CE

10

NU

11

VCC

12

13

VSS

14

NU

15

NU

CLE

16

17

ALE

18

WE

19

WP

NU

20

NU

21

NU

22

NU

23

NU

24

NU

I/O7

I/O6

I/O5

I/O4

NU

VCC

VSS

NU

I/O3

I/O2

I/O1

I/O0

NU

48

47

46

45

44

43

42

41

40

39

38

37

36

35

34

33

32

31

30

29

28

27

26

25

DIGITAL MAIN CBA UNIT

R3192 56x4

R3191 56x4

MMCDAT7

MMCDAT6

MMCDAT5

MMCDAT4

MMCDAT3

MMCDAT2

MMCDAT1

MMCDAT0

T

10-8

VSU X

W

PL14.22ASCD4

Digital Main 5 Schematic Diagram [TYPE A]

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.

CONTINUE DIGITAL 7

P-ON+5V

P-ON+3.3V

TU3001 TUNER UNIT

4

3

CONTINUE DIGITAL 8

UART1TX UART1RX

(NO CONNECTION)

(USB JACK)

GND 4 UARTORX 3 UARTOTX 2 P-ON+5V 1

CN3101

CN3704 1USB+5V

2USB0(-) 3USB0(+) 4GND

C3115 OPEN

C3742 220/6.3V

C3116 OPEN

C3117

R3101 10K

R3108

OPEN

IC3701 AP2151WG-7

(HIGH SIDE SWITCH)

1

2

34

VOUT

VIN

GND

/FLAG EN

R3758 100

5

R3761 10K

C3739 1

C3727

0.1

L3706 OPEN

*1

IC3101(4/7) MN2WS0270HA

DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

M1

NU N4 NU M2 NU

100R3193 100R3194 1KR3217

100R3176 100R3175

2.49KR3172

10kR3177

P5 NU

F21 UART1RX G20 UART1TX B25 NU D23 NU C24 UART0TX E22 UARTOTX

N22 USB0(-) M24 USB0(+)

AB8 NU N23 USB0VBUS

K23 NU K24 NU N24 USB0OD

DEMODULATOR /MPEG DECODER

TO DIGITAL MAIN 6 IC3101(5/7)

AB9NU AC9NU Y12NU AA15NU W14NU W10NU Y13NU

W8NU

AA8NU

AD9

AE9

AA13IF-AGC AA16TU-SDA Y15TU-SCL

10KR3004

4.7KR3011

4.7KR3025

L3005

2.2uH

C3041 OPEN

C3011

C3026 OPEN

C3014 L3004

0.1

C3027 OPEN

C3009

C3010

0.1

OPEN

C3040 10

C3013 39P

D3010 OPEN

C3039 OPEN

L3003

3.3uH0.1

3.3uH

10KR3001 33R3006 33R3007

+3.3V2GND3SDA4SCL5IF-AGC6DIF-OUT17DIF-OUT2

1

D3007 MM5Z5V6B

D3001

C3002

OPEN

C3003

D3002

OPEN

R3005 270

R3003 270

C3008

0.1

2

1

(NO CONNECTION)

WIRELESS LAN MODULE

CN3705 4USB+5V

3USB1(-) 2USB1(+) 1GND

CN3701 1USB1(+)

2USB1(-) 3USB+5V 4GND 5GND 6GND

R3735 OPEN

5

R3704 OPEN

C3715 OPEN

C3714 OPEN

C3716 OPEN

R3734 0

IC3702 OPEN

1

VOUT

VIN

2

GND

34

/FLAG EN

R3702 OPEN

DIGITAL MAIN CBA UNIT

ZAC

R3736 0

L3701 OPEN

(ETHERNET JACK)

CN3706

R8 GND

C3701

0.01

R7 NU R6 RX(-) R5 RCT R4 RX(+) R3 TX(-) R2 TCT R1 TX(+)

CONTINUE DIGITAL 7

AD

M22 USB1(-) L23 USB1(+)

10KR3180

M23 USB10D

M25 USB1VBUS

U10NU AC8RX(-)

AC7RX(+) AE6TX(-)

AD6TX(+)

AC6CTRL11 CTRL11

C3129 1

C3744

0.01

ABYAA

10-9

PL14.22ASCD5

Digital Main 6 Schematic Diagram [TYPE A]

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.

DIGITAL MAIN CBA UNIT

COMPONENT

-Pb-IN

COMPONENT

-Pr-IN

DIGITAL AUDIO OUT (COAXIAL)

AUDIO(L)-IN

AUDIO(R)-IN

JK3713 PC-RGB-IN

1

2

7

3

8

4514

9

10

JK3701

11156

12

13

R3741 33

C3720 100P

47KR3839

D3711 1SS400

D3712 1SS400

C3705 39P

C3770 39P

C3703 39P

C3708 100P

C3710 56P

C3711 56P

47KR3838

C3709 1

D3702 OPEN

R3708 10K

R3709 10K

D3705 OPEN

D3701 OPEN

D3704 OPEN

R3725 220

R3726 110

D3703 OPEN

D3707 OPEN

4

3

CONTINUE DIGITAL 4

COMP-DET

HP-DET

CONTINUE DIGITAL 7

P-ON+5V

P-ON+3.3V

AMP+13V

CONTINUE DIGITAL 8

VGA-SCL VGA-SDA

CONTINUE DIGITAL 2

P-ON-H2

COMPONENT-Y /VIDEO-IN

2

Q3821 2SA1576UBTLQ

(SWITCHING)

R3823

1.8K

R3825 47K

R3826 OPEN

R3822 10K

Q3822 2SC4081UBTLQ

(SWITCHING)

R3821 0

R3833 OPEN

R3820 0

C3815 1

1

CONTINUE DIGITAL 7

HP-MUTE

AUDIO-MUTE

LCD-P-ON

CONTINUE DIGITAL 8

SP-MUTE

R3828 OPEN

R3814 OPEN

R3815 OPEN

R3816 OPEN

R3811 1K

R3824 10K

R3817 OPEN

R3818 OPEN

R3819 OPEN

C3830 OPEN

R3832 OPEN

C3706

0.01

Q3709 2SC4081UBTLQ

(BUFFER)

C3707 33P

10KR3830

10KR3831

R3809 10K

R3813 10

R3812 100K

1C3805

1C3818

OPENR3805

0R3806

OPENR3807

1C3816

1C3817

1C3819

R3727 100

D3716 OPEN

D3717 OPEN

R3808 10K

R3723

C3704

10K

1

R3724 10K

D3714 OPEN

D3713 OPEN

D3715 OPEN

R3810 OPEN

IC3803 TPA3110D2PWPR (AUDIO AMP)

1

CONTROL LOGIC

2

3

POWER LIMIT

4

5

GAIN CONTROL

6

AVCC

7

8

GND

9

GVDD

10

11

POWER LIMIT

12

13

NU

14

PBTL PVCCR

PWM LOGIC

C3825

2.2

PVCCL

DRIVE

PVCCR

GND

C3824

0.047

28

27

26

25

24

23

22

21

20

19

18

17

16

15

R3171 75

C3842 10

C3831 OPEN

R3166 75

R3163 75

R3164 75

0.22C3801

0.22C3802

0.22C3803

C3827

0.047

0.22C3804

R3168 75

C3826 220/16V

R3167 75

C3828

2.2

C3829 220/16V

1C3121 1C3118 1C3119 1C3120 1C3109 1C3113 1C3114

C3843 10

R3801 OPEN

C3807 OPEN

R3802 OPEN

C3808 OPEN

R3803 OPEN

C3809 OPEN

R3804 OPEN

C3810 OPEN

L3801 10uH

L3802 10uH

L3803 10uH

L3804 10uH1C3806

R3147 36 R3148 36 R3149 36 R3145 36

R3713 OPEN

C3811 1000P

C3812 1000P

C3813 1000P

C3814 1000P

1C3207 1C3208

R3216 10 R3218 10 R3219 10 R3220 100 R3221 100 R3222 100

R3155 100 R3154 100

R3195 10K R3196 10K R3197 10K

R3199 OPEN

R3297 100K R3298 100K

R3731 OPEN

R3739 OPEN

R3732 OPEN

C3820 1

C3821 1

C3822 1

C3823 1

*1

IC3101(5/7) MN2WS0270HA

DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

AE12 NU AC12 NU AD12 NU

Y9 NU Y10 NU AA9 NU AC10 NU

10R3214

AB10 AD11 AB11 AC11 AD13 AB13JK3706 AC13

Y11 VGA-HSYNC AA12 VGA-VSYNC

1C3103

W11

1C3104

AA11

1C3105

AB12

1C3102

AA10

E4 NU

D2 NU

F6 NU

G5 NU

E3 NU

SPDIF

F4 AE14 AC14 AB14 NU AC15 NU AC16 NU AD16 NU AB16 NU AE17 NU AD17 AC17 AB17 AC18

E2 AUDIO-MUTE

F5 ARC-OUT

R3740 OPEN

Q3710

OPEN C3718 OPEN

C3834

C3838

OPEN

C3835

C3839

OPEN

C3836

C3840

OPEN

C3837

C3841

OPEN

R3728

3.3

R3729

3.3

R3752 OPEN

D3801 OPEN

D3802 OPEN

D3803 OPEN

D3804 OPEN

SW

AUDIO I/F

C3713 220/6.3V

R3737 10K

A/D CONVERTER

DIGITAL SIGNAL PROCESS

TO DIGITAL MAIN 1 IC3101(1/7)

TO DIGITAL MAIN 8 IC3101(7/7)

TO DIGITAL MAIN 5 IC3101(4/7)

R3746 10K

Q3708 OPEN

R3733

4.7K

R3738 10K

R3744 OPEN

TO DIGITAL MAIN 3 IC3101(2/7)

TO DIGITAL MAIN 4 IC3101(3/7)

TO DIGITAL MAIN 8 IC3101(7/7)

TO DIGITAL MAIN 5 IC3101(4/7)

C3712 220/6.3V

CN3801

R3743 10K

Q3701 OPEN

1 SP(L)+ 2 SP(L)3 SP(R)4 SP(R)+

R3751 47K

JK3801 HEADPHONE JACK

ARC-OUT

SP3801 SPEAKER

L-CH

SP3802 SPEAKER

R-CH

CONTINUE DIGITAL 8

AE AF AG AH AI AJ

10-10

PL14.22ASCD6

Digital Main 7 Schematic Diagram [TYPE A]

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.

CONTINUE DIGITAL 1

P-ON+21V

P-ON+3.3V

CONTINUE DIGITAL 2

P-ON+21V

P-ON+3.3V

4

3

2

1

CONTINUE DIGITAL 6

HP-MUTE

AUDIO-MUTE

LCD-P-ON

CONTINUE DIGITAL 8

STB-RESET

LCD-P-ON

BACKLIGHT-SW

PROTECT3 PROTECT1

P-ON-H2 HP-MUTE

CONTINUE DIGITAL 1

BACKLIGHT-ADJ

TO POWER SUPPLY CBA CN501

CONTINUE DIGITAL 6

CONTINUE DIGITAL 4

CONTINUE DIGITAL 5

CONTINUE DIGITAL 8

CN3601

10GND 11GND 12GND 13GND 14GND 15AMP+13V 16AMP+13V 17AMP+13V 18AMP+13V 19GND 20P-ON+21V 21P-ON+21V 22P-ON+21V 23P-ON+21V

P-ON+5V

P-ON+3.3V

AMP+13V

P-ON+3.3V

P-ON+5V AL+3.3V

P-ON+5V

P-ON+3.3V

P-ON+5V

P-ON+3.3V

AL+3.3V

1NU 2PROTECT1(NU) 3PROTECT3 4RESET 5BACKLIGHT-SW 6P-ON-H2 7BACKLIGHT-ADJ 8AL+3.3V 9GND

R3610 OPEN

R3607

R3602 220

D3603 OPEN

R3608 270

D3605 MM5Z15B

R3615 10K

56K

Q3602 2SA1576UBTLQ

(SW+12V)

R3618

4.7K

D3601 OPEN

D3602 OPEN

C3652 OPEN

D3610 MM5Z4V3B

C3650 OPEN

R3601 OPEN

100R3620 100R3603

100R3645 100R3629 100R3647

C3676 OPEN

Q3603 2SC4081UBTLQ

(SWITCHING)

DIGITAL MAIN CBA UNIT

R3609 10K

R3611 OPEN

R3612 OPEN

C3602 1

R3621 OPEN

Q3601 OPEN

IC3601 PST8429UR (RESET)

GND OUT

14

CDVDD

32

R3622 10K

D3609 OPEN

D3608 1SS400

R3619 10K

C3610 1

R3630 0

C3605 1000P

C3606

0.01

C3613 OPEN

D3607 OPEN

R3095 10K

D3606 1SS400

R3631 0

R3623 22K

C3645

4.7

C3655

0.1

C3604 OPEN

C3665 OPEN

C3618 OPEN

C3656

0.1

R3628 1K

R3627 100K

C3616

4.7

R3606 11K

R3604

6.2K

C3674

4.7

R3635

5.1K

R3633 10K

C3668 470/4V

C3625

4.7

R3614

4.3K

R3617 10K

D3615 KDZTR6.8B

C3639

0.01

C3654 OPEN

C3615

0.1

C3675

0.1

C3672 10

C3632

0.1

IC3604 RT8293ALZSP (+1.14V REG.)

1

BS

2

VIN

3

SW

45

GND FB

L3601 10uH

R3689 OPEN

C3969 OPEN

C3609 OPEN

IC3603 MP1472GJC452Z (+3.3V REG.)

C3607

0.033 1

SS

2

EN C3611 3300P

3

COMB

45

FB GND

R3677 15K

R3605 1K

C3608 10

C3673 OPEN

IC3602 MP1472GJC452Z (+1.5V REG.)

C3661

0.033

1

SS

2

EN C3666 4700P

3

COMB

45

FB GND

R3679

6.2K R3634

100

C3670 10

C3631 OPEN

IC3607 MP1472GJC452Z (+5V REG.)

C3617

0.1

1

SS

2

EN C3619 4700P

3

COMB

45

FB GND

R3678 12K

R3616 33K

C3628 10

SS

EN

COMP

C3646 OPEN

BST

VIN

SW

C3603 10

BST

VIN

SW

C3671 10

BST

VIN

SW

C3621 10

8

7

6

C3641 10

8

7

6

L3604 22uH

C3614 10

8

7

6

L3603 10uH

C3669 OPEN

8

7

6

L3605 22uH

C3623 OPEN

C3630 OPEN

C3601

0.015

R3676 OPEN

R3624 OPEN

C3643 10

R3626 0

R3613 OPEN

C3612

0.01

R3687 OPEN

C3967 OPEN

C3667

0.01

R3685 OPEN

C3968 OPEN

C3620

0.01

R3696 OPEN

C3966 OPEN

C3642 OPEN

C3638

0.015

R3625

2.2K

C3644 OPEN

*1

IC3101(6/7) MN2WS0270HA

DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

AFB R4

AVDDDMD33 U11

AVDDADA33 T15

AVDD33-CEN P10

AVDD33-TX P9

STMADAVDD33 M10

STMRONA T4

0R3022

HEAT SINK

0R3023 0R3024

C3182 2700P

R3223 0

C3183 OPEN

C3134

R3181

1

0

U12AVDDVAD11 K11LVVDD11

*AVDD11

L3102 0

AC21AVDDH11 AD21AVDDH11

C3133 OPEN

T9AVDD11-CEN AB4AVDD11-RX T10DVDD11 N12VDD33-1 N13VDD33-2 M12DPAVDD33 AB21AVDDH33 M13VDDEM18-33 L11LVVDD33-1 M11LVVDD33-2 N11LVVDD33-3

W9VCOMP

J4LVDSRREF L22USBRREF AD14VREF1V5 T16AVDDHP33 R15AVDDPLL33 U15AVDDV33 R16AVDDAPUSB33

AB15AVDDEVE33

J21VDDSD18-33

M9VDDTCON25-33

L10VDDSTM33

*BVDDIO15

D5VDDIOCK15 N10VDDSTM11

N9FPEN R12TESTSEL

*CNU

*DGND

C3136

C3142

C3132

10

1

C3143

C3139

1

C3147

C3148

0.1

C3178

C3179

1

C3155

0.1

1C3180 24KR3186

6.2KR3187 1C3181

C3159

C3160

10

0.1

C3163

C3164

0.1

C3165

C3166

10

C3169

0.1

C3170

C317110C3177

0.1

C3168

0.1

C3173

C3174

10

0.1

C3152

C3153

1

10

C3140

C3137

1

C3154

0.1 C3175 1

*A:J11~J17,K12~K17,L14~L17,M15~M17 *B:E9,F8,F9,G13~G15,G19 *C:H5,P23,R13,R23,R24,T13,T22,T23,U22,U24,U25,

V5,AD1,AD2,AE2 *D:A1,A9,A25,C10,D13,E5,E6,E12,E13,F7,F13,F15,

G17,G18,H7,H8,J9,J10,K9,K10,L9,L12,L13,M14, N6,N7,N14~N17,P11~P17,R10,R11,R14,R17,T11, T12,T14,T17,U13,U14,U16,U17,W12,W13,Y14, AA14,AC4,AE1,AE25

10

C3144 1

C3149

0.1

C3156 10

C3161

0.1

R3185 560

C3167

0.1

C3172 1

C3141 1

C3151 1

C3138 1

C3130

0.1

C3157

0.1

C3162

0.1

C3135 10

C3145 1

C3184 1

C3131

0.1

C3158

0.1

L3101 BEAD

L3104 BEAD

L3105 BEAD

L3107 BEAD

R3183 0

L3106 BEAD

R3184 0

C3146 1

C3185 1

L3103

2.2uH

C3150 1

L3108 BEAD

CTRL11

AL+3.3V VCC+1.5V

CONTINUE DIGITAL 5

CONTINUE DIGITAL 3

10-11

APAOANAMALAK

PL14.22ASCD7

Digital Main 8 Schematic Diagram [TYPE A]

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.

DIGITAL MAIN CBA UNIT

4

3

2

1

(NO CONNECTION)

CONTINUE DIGITAL 2

CONTINUE DIGITAL 7

TO IR SENSOR CBA UNIT CN4052

CONTINUE DIGITAL 4

CONTINUE DIGITAL 7

CONTINUE DIGITAL 6

CONTINUE DIGITAL 5

CN3103

AL+3.3V 1 P-ON-H2 2

PROTECT3

P-ON+5V

P-ON+3.3V

AL+3.3V

CN3105 1SDA(NU)

2SCL(NU) V3 LED1 3GND 4KEY-IN1 5REMOTE 6LED1 7LIGHT 8P-ON+5V 9AL+3.3V

STB-RESET

STMTIME1

STB-RESET

BACKLIGHT-SW

PROTECT3 PROTECT1

P-ON-H2 HP-MUTE

SP-MUTE

UART1TX UART1RX

R3131 1K

R3212 100K

R3096 22K

C3101

0.1

R3110 33

C3100 OPEN

R3114 33

R3117 10

C3111

0.1

OPENC3122 OPENC3123

R3144 0

Q3107 OPEN

R3188 OPEN

R3206 OPEN

R3215 OPEN

R3207 OPEN

R3107 100

C3107 OPEN

C3110

C3112

OPEN

D3101 MM5Z5V6B

C3127

0.1 IC3103

M24C16-WMN6TP (MEMORY)

1

A0

VCC

2

A1

3

A2

SCL

45

VSS SDA

R3209 OPEN

R3200 OPEN

Q3108 OPEN

R3102 1K

Q3101 2SC4081UBTLQ

(LED DRIVE)

R3105 100

8

7

WP

6

R3150 10K

R3152

4.7K

R3151 10K

R3323 33

R3119 OPEN

Q3103 OPEN

R3153

4.7K

R3120 OPEN

C3108 1

R3103 OPEN

R3143 OPEN

Q3102 2SC4081UBTLQ

(BUFFER)

R3106

R3159

10K

0

R3104

C3106

27K

33/10V OPEN

*1

IC3101(7/7) MN2WS0270HA DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

10KR3109

AA4 NU

Y1 NU AB1 NU AB3 NU AB2 NU

Y4 NU

V6 NU AA3 NU

V4 NU

W4 LED2

Y5 SW-EN

U3 REMOTE

R3146 100K

T3 LIGHT-SENS

R3182

U1 KEY-IN1

100R3161

T2 PROTECT3

100R3160

U5 PROTECT1 AD5 STB-RESET

22R3162

W2 LCD-P-ONLCD-P-ON

100R3133

W3 BACKLIGHT-SW

Y2 P-ON-H2

OPENR3138

AB6 P-ON-H2

W7 HP-MUTE

W5 STMTIME1

AA2 SP-MUTE

39R3156

AC2 STM-SCL

39R3157

AC1 STM-SDA

22R3158

U4 STM-EEPROM-WP

Q3705 2SC4081UBTLQ

(SWITCHING)

R3730 0

Q3706 OPEN

AUDIO DECODER

TO DIGITAL MAIN 6 IC3101(5/7)

R3771 OPEN

R3772 OPEN

R3717 0

R3716 33K

C3719 220P

R3714

HDMI I/F

VIDEO DECODER

TO DIGITAL MAIN 6 IC3101(5/7)

R3720 33K

C3717 220P

R3715 10K

AD24 AE24 AD23 AE23 AC23 AE22 AD22 AC22 Y23 AA24 AA23 AB25 AB24 AC25 AC24 AD25 U23 V24 V23 V22 W23 W22 Y25 Y24

AE3HDMI1-SDA

AA5HDMI2-SDA

HDMI0-HPD

AB5HDMIO-5V AA6HDMI1-5V AC3HDMI2-5V

AD3VGA-SDA

Q370410K 2SC4081UBTLQ

(SWITCHING)

CONTINUE DIGITAL 6

C3012

R3002

1

10K

R3703 10K

R3710 10K

R3712 10K

R3701

R3707

R3711

R3718 47K

R3781 47K

R3773 47K

R3721 10K

C3702

R3722

0.1

47K

100R3179

Y3HDMI-CEC T6STMCECPUL T7HDMI0-SCL W6HDMI0-SDA R9HDMI1-SCL

V7HDMI2-SCL

R7 U2HDMI1-HPD U6HDMI2-HPD

R3863 27K

D3722 1SS400

R3165

Y7VGA-SCL

U7NU Y6HDMI-UART-CTRL

39 39R3178

R3865 22

39R3134 39R3137 39R3139 39R3140 39R3141 39R3142

C3759

0.1

C3750

0.1

R3784 10K

R3785 47K

R3777 10K

R3778 47K

R3014

R3008

160

82

R3706 47K

R3705 1K

Q370710K 2SC4081UBTLQ

(SWITCHING)

R3780 47K

R3779 1K

Q370210K 2SC4081UBTLQ

(SWITCHING)

R3774 47K

R3775 1K

Q370310K 2SC4081UBTLQ

(SWITCHING)

ARC-OUT

JK3717

1 DATA2(+) 2 TMDS DATA2 SHIELD 3 DATA2(-) 4 DATA1(+) 5 TMDS DATA1 SHIELD 6 DATA1(-) 7 DATA0(+) 8 TMDS DATA0 SHIELD

9 DATA0(-) 10 CLOCK(+) 11 TMDS CLOCK SHIELD 12 CLOCK(-) 13 HDMI-CEC 14 ARC 15 HDMI-CLOCK 16 HDMI-DATA 17 GND 18 +5V 19 HOT PLUG DETECT

R3719 OPEN

JK3716

1 DATA2(+)

2 TMDS DATA2 SHIELD

3 DATA2(-)

4 DATA1(+)

5 TMDS DATA1 SHIELD

6 DATA1(-)

7 DATA0(+)

8 TMDS DATA0 SHIELD

9 DATA0(-) 10 CLOCK(+) 11 TMDS CLOCK SHIELD 12 CLOCK(-) 13 HDMI-CEC 14 NU 15 HDMI-CLOCK 16 HDMI-DATA 17 GND 18 +5V 19 HOT PLUG DETECT

R3783 OPEN

JK3715

1 DATA2(+)

2 TMDS DATA2 SHIELD

3 DATA2(-)

4 DATA1(+)

5 TMDS DATA1 SHIELD

6 DATA1(-)

7 DATA0(+)

8 TMDS DATA0 SHIELD

9 DATA0(-) 10 CLOCK(+) 11 TMDS CLOCK SHIELD 12 CLOCK(-) 13 HDMI-CEC 14 NU 15 HDMI-CLOCK 16 HDMI-DATA 17 GND 18 HDMI+5V 19 HOT-PLUG-DETECT

R3776 OPEN

VGA-SCL VGA-SDA

HDMICONNECTOR-1

HDMICONNECTOR-3

HDMICONNECTOR-2

CONTINUE DIGITAL 6

AQ

AR AS AT AU AV

10-12

PL14.22ASCD8

Digital Main 1 Schematic Diagram [TYPE B]

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into four and shown as IC3101 (1/4) ~ IC3101 (4/4) in this Digital Main Schematic Diagram Section.

4

3

2

1

DIGITAL MAIN CBA UNIT

R3213 1K

C3204 OPEN

IC3201 MP1472GJC452Z (+12V REG.)

C3201

0.033

C3252 OPEN

R3202 18K

R3209 120K

C3211

4.7

D3108 OPEN

1

SS

2 C3203 1000P

R3208 1K

C3213

C3212

4.7

R3178 220

C3106 1

33R3089

33R3092

R3194 33R3093 OPEN

EN

3

COMP

45

FB GND

R3205 10K

C3210

OPEN

IC3009 PST8429UR (RESET)

14

GND OUT

IC3006 W25Q32FVSSIG (MEMORY)

1

2

3

45

BST

IN

SW

C3205D3203

4.7

32

CDVDD

CS

VCC

SO

NU

WP

SCL

GND SDA

8

7

6

C3113

0.033

C3216 OPEN

8

7

6

C3202

0.1

L3201 33uH

R3216 10K

R3182 56K

C3116

0.01

R3102

4.7K

R3107 10K

R3217 OPEN

R3218 OPEN

D3109 OPEN

R3119 OPEN

C3073

0.1

33R3094

C3001 OPEN

C3214

4.7

D3110 OPEN

R3242 OPEN

R3241 100

C3207

4.7

C3208

C3209

0.1

OPEN

C3110 OPEN

R3219 10K

Q3104 2SC4081UBTLQ

(SWITCHING)

33R3104

R3044 OPEN

Q3007 OPEN

*1

IC3101(1/4) MSD8220LB1-S1

DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

122

CPU-RESET

LVDS TX

102 WP 113 CS 111 SOUT 112 SPI-SDA 114 SPI-SCL

TO DIGITAL MAIN 2 IC3101(2/4)

R3045 OPEN

R3047 OPEN

91 90 89 88 86 85

84 83

82 81 80 79

78 77 76 75 74 73

72 71

70 69 68 67

R3046 OPEN

C3000 OPEN

R3048 OPEN

OPENR3149 OPENR3153

OPENR3248 OPENR3249

C3057 OPEN

OPENC3684

OPENC3683

3PC3682

C3058 OPEN

3PC3681

3PC3679

3PC3680

3PC3677

3PC3678

3PC3676

3PC3675

3PC3674

3PC3673

R3168 OPEN

OPENC3672

OPENC3671

3PC3670

3PC3669

R3130 0

3PC3668

3PC3667

3PC3666

3PC3665

3PC3663

3PC3664

OPENR3095

OPENC3166 OPENC3167

OPENR3129

3PC3661

3PC3662

R3172 0

C3170

4.7

R3171 OPEN

R3193

C3171 1000P

CONTINUE DIGITAL 4

P-ON+21V AL+3.3V P-ON+3.3V

CONTINUE DIGITAL 4

1SS400STD3204

OPENR3099 OPENR3098

0

OPEN

R3195

R3192

OPENR3096 OPENR3097

OPENR3170 OPENR3169

OPENR3167 OPENR3166 OPENR3165

OPENR3254 OPENR3253

OPENR3252 OPENR3251

RESET PROTECT3 CELL-PWR-CTRL VCOM-PWM

CN3803

(NO CONNECTION)

1 GND 2NU 3 SCL 4 SDA

0

R3196

TO LCD PANEL ASSEMBLY

CN3013

51 NU 50 SCL 49 SDA 48 NU 47 NU 46 CELL-PWR-CTRL 45 SELLVDS 44 NU 43 NU 42 NU 41 GND 40 RXE0(-) 39 RXE0(+) 38 RXE1(-) 37 RXE1(+) 36 RXE2(-) 35 RXE2(+) 34 GND 33 RXECLK(-) 32 RXECLK(+) 31 GND 30 RXE3(-) 29 RXE3(+) 28 NU 27 NU 26 GND 25 GND 24 RXO0(-) 23 RXO0(+) 22 RXO1(-) 21 RXO1(+) 20 RXO2(-) 19 RXO2(+) 18 GND 17 RXOCLK(-) 16 RXOCLK(+) 15 GND 14 RX03(-) 13 RXO3(+) 12 NU 11 NU 10 GND

9 GND 8 GND 7 GND 6 GND 5NU 4 LCD+12V 3 LCD+12V 2 LCD+12V 1 LCD+12V

AECB

10-13

D

F

PL14.22BSCD1

Digital Main 2 Schematic Diagram [TYPE B]

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into four and shown as IC3101 (1/4) ~ IC3101 (4/4) in this Digital Main Schematic Diagram Section.

COMPONENT

-Pb-IN

COMPONENT

-Pr-IN

DIGITAL AUDIO OUT (COAXIAL)

AUDIO(L)-IN

AUDIO(R)-IN

JK3005 PC-RGB-IN

1

2

7

3

8

4514

9

10

C3253 OPEN

R3811 10K

R3812

JK3702

JK3701

11156

12

13

C3255 OPEN

R3814 10K

R3825 0

D3806 OPEN

4.7KR3321

C3254 OPEN

R3863 OPEN

C3701 10P

C3702 10P

C3703 10P

C3709 100P

C3720 330P

C3719 330P

4.7KR3326

D3805 OPEN

C3706 1

R3706 10K

R3707 10K

D3054 OPEN

D3041 OPEN

C3830

0.1

Q380110K 2SC4081UBTLQ

(SWITCHING)

R3126 75

R3125 75

R3127 75

C3715 OPEN

R3713 12K

R3714 12K

R3815 100K

R3708 110

D3049 OPEN

C3718 560P

C3713 560P

D3053 OPEN

C3708

0.1

R3709 220

D3055 OPEN

D3045 OPEN

C3815 1

Q3701 2SC4081UBTLQ

(BUFFER)

10PC3009

10PC3007

D3050 OPEN

R3821 OPEN

R3710 100

10PC3002

10KR3347

R3809 10K

R3820 10

1C3805

1C3818

OPENR3805

0R3806

OPENR3807

1C3816

1C3817

1C3819

R3711 OPEN

R3712 10K

10KR3358

R3810 OPEN

IC3801 TPA3110D2PWPR (AUDIO AMP)

1

2

3

4

5

6

7

AVCC

8

GND

9

GVDD R3808 10K

10

11

12

13

NU

14

PBTL PVCCR

4

3

2

1

(NO CONNECTION)

CONTINUE DIGITAL 4

CONTINUE DIGITAL 3

CONTINUE DIGITAL 4

CN3010 1AL+5V

2UART0-TX 3UART0-RX 4GND

P-ON+3.3V

AL+3.3V

AL+5V

AMP+13V

UARTRXD0 UARTTXD0

BACKLIGHT-SW

AMP-MUTE

HP-MUTE

COMPONENT-Y /VIDEO-IN

C3707 1

R3716

3.3K

R3339 100

R3343 100

CONTROL LOGIC

POWER LIMIT

GAIN CONTROL

POWER LIMIT

PWM LOGIC

PVCCL

DRIVE

PVCCR

GND

R3146 75

R3148 75

28

27

26

25

24

23

22

21

20

19

18

17

16

15

R3200 10K

R3147 75

C3827

4.7

C3831 220/16V

C3824

4.7

R3144 33 R3136 33 R3123 0

68R3124 0.047C3141

R3122 33 R3135 33 R3131 0 1000PC3137

200KR3164

1000PC3147

200KR3175

1000PC3148

0.22C3801

0.22C3802

0.22C3803

C3825

4.7

0.22C38041C3806

C3828

C3829

4.7

100/16V

0.047C3118

0.047C3139 1000PC3119

0.047C314033R3138

0.047C312468R3128

0.047C3136

0.047C3135

0.047C3117R3121 68

0.047C3134R3134 33

47R3115 47R3114

R3198 100

2.2C3126

2.2C3125

1000PC3105

200KR3163

1000PC3104

R3816 33

*1

IC3101(2/4) MSD8220LB1-S1

DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

COMP-DET64 26 22 23 24

NU25

NU30 14 VGA-HSYNC 15 17 16 18 19 20 VGA-VSYNC

116 VGA-SDA 117 VGA-SCL

SPDIF

62 35 34

200KR3190

44 45 46 47

R3824 OPEN

R3861 OPEN

L3801

R3801

33uH

OPEN C3807

OPEN

L3802 33uH

R3802 OPEN

C3808 OPEN

L3803 33uH

R3803 OPEN

C3809 OPEN

L3804 33uH

R3804 OPEN

C3810 OPEN

C3811 1000P

C3812 1000P

C3813 1000P

C3814 1000P

AUDIO I/F

R3862 OPEN

C3820 OPEN

C3821 1

C3822 OPEN

C3823 1

SW

Q3861 OPEN

C38261C3832 OPEN

C3833 OPEN

C38351C3836 OPEN

C3837 OPEN

A/D CONVERTER

DIGITAL SIGNAL PROCESS

TO DIGITAL MAIN 3 IC3101(3/4)

D3811

R3813

GR1BOPEN

C3858 1

C3834 OPEN

C3838 OPEN

D3801 OPEN

D3802 OPEN

D3803 OPEN

D3804 OPEN

TO DIGITAL MAIN 1 IC3101(1/4)

TO DIGITAL MAIN 3 IC3101(3/4)

HP-DET

C3852

R3852

0.33

20K

R3866 100K

R3867 47K

C3851

R3851

0.33

20K

123USB(-) 124USB(+)

103VBUS-ST 61VBUS-EN

99

C3860 OPEN

C3857 10

R3865 OPEN

R3823 OPEN

BIAS

5.1R3021

5.1R3020

22R3176

R3112 100

R3854 33K

3

4

GND5STDBY

6

DIGITAL MAIN CBA UNIT

L3025 OPEN

C3348

C3246

220/6.3V

1

IC3019 AP2151WG-7

(HIGH SIDE SW)

1

5

OUT

IN

C3327

R3702 1K

1

R3480 10K

R3705 10K

C3704

0.1

D3703 OPEN

R3479 10K

1

2

VCC

IC3851 TS488IQT

(HEADPHONE AMP)

7

8

R3853 33K

2

GND

34

/FLAG RN

C3710 220/6.3V

D3701 OPEN

C3705 220/6.3V

D37021KR3704 OPEN

D3052 OPEN

CN3801

1 SP(L)+ 2 SP(L)3 SP(R)4 SP(R)+

CN3009 (USB JACK)

1 BUS-POWER 2 USB(-) 3 USB(+) 4 GND

JK3703 HEADPHONE

JACK

SP3801 SPEAKER

L-CH

SP3802 SPEAKER

R-CH

HI

JG

10-14

KL

PL14.22BSCD2

Digital Main 3 Schematic Diagram [TYPE B]

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into four and shown as IC3101 (1/4) ~ IC3101 (4/4) in this Digital Main Schematic Diagram Section.

DIGITAL MAIN CBA UNIT

TU3901 (TUNER UNIT)

4

3

2

1

CONTINUE DIGITAL 4

AL+5V

AL+3.3V

P-ON+3.3V

TO IR SENSOR CBA UNIT CN4052

CONTINUE DIGITAL 2

UARTRXD0 UARTTXD0

CN3101 1SDA(NU)

2SCL(NU) 3GND 4KEY-IN1 5REMOTE 6LED1 7LIGHT 8P-ON+5V 9AL+3.3V

C3904 OPEN

C3906 OPEN

+3.3V2GND3SDA4SCL5IF-AGC6DIF-OUT17DIF-OUT2

1

C3907 OPEN

D3901

C3905

MM5Z5V6B

10

R3822 10

C3554 1

OPENC3551 OPENC3552

R3556 OPEN

4.7KR3501

4.7KR3502

R3557 OPEN

L3913

2.2uH

C3910

0.1

C3927 33P

R3536 0

C3555 OPEN

R3552 100

C3553 OPEN

C3926 33P

D3904 MM5Z5V6B

Q3531 OPEN

C3559 OPEN

C3556 OPEN

C3909 33P

D3903 MM5Z5V6B

R3936 100

R3534 OPEN

R3535 OPEN

R3551 100

Q3501 2SC4081UBTLQ

(LED DRIVE)

D3501 MM5Z5V6B

R3503 OPEN

R3558 OPEN

R3555 OPEN

R3553 100

C3173

0.1

C3174

0.1

C3908 33P

D3902 MM5Z5V6B

Q3502 2SA1576UBTLQ

(LED DRIVE)

R3559 10K

R3560 100K

R3137 10K

R3151 33

R3152 33

R3179 0

C3168

0.022

C3557 OPEN

R3206 47

C3144 OPEN

C3145 L3108 OPEN

C3150 OPEN

R3207 47

R3937

4.7K

R3938

4.7K

R3183 100

C3558 10

R3184 OPEN

C3172 15P

X3101 24MHz

C3169 18P

OPEN

L3104 22uH

Q3010 2SC4081UBTLQ

(BUFFER)

R3185 10K

R3186 39K

R3157 160

R3181 51

R3187 51

C3101 OPEN

C3142

0.1

C3143

0.1

R3180 10K

C3149 1

R3158 OPEN

22R3103

4.7KR3116

R3105 22

OPENR3109 OPENR3110

100R3201

*1

IC3101(3/4) MSD8220LB1-S1

DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

53 XIN

54 XOUT

49

DEMODULATOR /MPEG DECODER

50

TO DIGITAL MAIN 2 IC3101(2/4)

TU-SCL59 TU-SDA58

48 IF-AGC

105 SW-EN

120 REMOTE 100 LED1

130 LIGHT

128 KEY-IN1

66 SW-SCL 65 SW-SDA

60 FACTORY-SEL

R3080 10K

Q3011 2SC4081UBTLQ

(SWITCHING)

TO DIGITAL MAIN 2 IC3101(2/4)

R3081 100

TO DIGITAL MAIN 2 IC3101(2/4)

R3078 1K

Q3003 2SC4081UBTLQ

(SWITCHING)

AUDIO DECODER

R3075 1K

HDMI I/F

VIDEO DECODER

TO DIGITAL MAIN 2 IC3101(2/4)

R3074 33K

C3003 330P

R3073 10K

13 12 11 10

136 137

152 151 150 149 148 147 146 145 134 135

156 155 154 153 140 139

115HDMI-ARC

119HDMI-CEC

142HDMI-5V2 107HDMI3-HPD 141HDMI2-HPD 108HDMI1-HPD

HDMI-

JK3002

CONNECTOR-2

1 DATA2(+) 2 TMDS DATA2 SHIELD 3 DATA2(-)

4 DATA1(+) 9 8 7 6

100R3022 100R3023

R3275

R3278

47K

C3023

0.1

R3066 47K

100R3042 100R3050

4 3 2 1

R3212

R3214

47K

R3076 33K

47K

R3003 47K

R3019 47K

R3005 47K

R3422 OPEN

Q3002 2SC4081UBTLQ

(SWITCHING)

R3082 OPEN

R3118 OPEN

100R3407 100R3406

C3012 OPEN

100R3113

10R3001

33R3111 0R3117

R3077 OPEN

Q3004 2SA1576UBTLQ

(SWITCHING)

R3079 10K

R3071 10K

R3063 1K

R3018 1K

R3401 33

R3421 OPEN

C3005

0.1

C3404

0.1

R3055 1K

Q3008 2SC4081UBTLQ

(SWITCHING)

R3010 1K

Q3001 2SC4081UBTLQ

(SWITCHING)

R3420 OPEN

R3423 OPEN

Q3407 OPEN

5 TMDS DATA1 SHIELD

6 DATA1(-)

7 DATA0(+)

8 TMDS DATA0 SHIELD

9 DATA0(-)

10 CLOCK(+) 11 TMDS CLOCK SHIELD 12 CLOCK(-) 13 HDMI-CEC 14 NU 15 HDMI-CLOCK 16 HDMI-DATA 17 GND 18 +5V 19 HOT PLUG DETECT

R3058 OPEN

JK3003

1 DATA2(+)

2 TMDS DATA2 SHIELD

3 DATA2(-)

4 DATA1(+)

5 TMDS DATA1 SHIELD

6 DATA1(-)

7 DATA0(+)

8 TMDS DATA0 SHIELD

9 DATA0(-)

10 CLOCK(+) 11 TMDS CLOCK SHIELD 12 CLOCK(-) 13 HDMI-CEC 14 NU 15 HDMI-CLOCK 16 HDMI-DATA 17 GND 18 +5V 19 HOT PLUG DETECT

R3017 OPEN

JK3004

1 DATA2(+)

2 TMDS DATA2 SHIELD

3 DATA2(-)

4 DATA1(+)

5 TMDS DATA1 SHIELD

6 DATA1(-)

7 DATA0(+)

8 TMDS DATA0 SHIELD

9 DATA0(-)

10 CLOCK(+) 11 TMDS CLOCK SHIELD 12 CLOCK(-) 13 HDMI-CEC 14 NU 15 HDMI-CLOCK 16 HDMI-DATA 17 GND 18 HDMI+5V 19 HOT-PLUG-DETECT

HDMICONNECTOR-1

HDMICONNECTOR-3

M

NOPQR

10-15

PL14.22BSCD3

Digital Main 4 Schematic Diagram [TYPE B]

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into four and shown as IC3101 (1/4) ~ IC3101 (4/4) in this Digital Main Schematic Diagram Section.

DIGITAL MAIN CBA UNIT

CONTINUE DIGITAL 3

AL+5V

AL+3.3V

P-ON+3.3V

4

CONTINUE DIGITAL 2

P-ON+3.3V

AL+3.3V

AL+5V

3

2

1

AMP+13V

CONTINUE DIGITAL 1

P-ON+21V

AL+3.3V

P-ON+3.3V

TO POWER SUPPLY CBA CN501

P-ON-H2 18

(NO CONNECTION)

P-ON-H2 6

CONTINUE DIGITAL 1

RESET

PROTECT3

CELL-PWR-CTRL

VCOM-PWM

CONTINUE DIGITAL 2

BACKLIGHT-SW

AMP-MUTE

HP-MUTE

CN3602

23NU 22PROTECT1(NU) 21PROTECT3 20RESET 19BACKLIGHT-SW

17BACKLIGHT-ADJ 16AL+3.3V 15GND 14GND 13GND 12GND 11GND 10GND

9AMP+13V 8AMP+13V 7AMP+13V 6AMP+13V 5GND 4P-ON+21V 3P-ON+21V 2P-ON+21V 1P-ON+21V

CN3601 1NU

2PROTECT1(NU) 3PROTECT3 4RESET 5BACKLIGHT-SW

7BACKLIGHT-ADJ 8AL+3.3V

9GND 10GND 11GND 12GND 13GND 14GND 15AMP+13V 16AMP+13V 17AMP+13V 18AMP+13V 19GND 20P-ON+21V 21P-ON+21V 22P-ON+21V 23P-ON+21V

100R3631

100R3638

100R3632

100R3633

OPENC3650 OPENC3644 OPENC3653 OPENC3604 OPENC3651 OPENC3603

D3607 OPEN

C3648 OPEN

C3656 OPEN

270R3635

OPENR3637

C3639

4.7

C3607

4.7

C3616

4.7

C3625

C3626

OPEN

R3628 68K

C3615 OPEN

C3652

0.1

C3637

OPEN

4.7

IC3604 MP2314GJ-Z (+5V REG.)

1

AAM

2

IN

3

SW

EN/SYNC

45

GND BST

VCC

FB

C3601

0.1

8

7

6

C3618

0.1

R3621 20

C3619

0.1

L3602 10uH

IC3605 MP2314GJ-Z (+1.18V REG.)

R3627 47K

1

AAM

2

IN

C3624

4.7

D3011 MM5Z3V9B

R3007 47K

R3618 100K

C3621 10

D3610 MM5Z6V8B

R3647 22K

VCC

3

SW

EN/SYNC

45

GND BST

R3622 22K

C3643 33P

C3638 10

R3648 1K

IC3602 AP1117EG-13 (+3.3V REG.)

VOUT

VIN

COM

123

R3606

C3614 10

8

FB

C3628

0.1

7

6

R3615 33K

R3616

6.8K

C3623

Q3601 2SC4081UBTLQ

(SWITCHING) (SWITCHING)

C3642 OPEN

R3634 20

C3629

0.1

L3603

4.7uH

C3632 220/6.3V 10

R3614

7.5K

C3620

D3608

220/6.3V

OPEN10

C3633 10

D3601 1SS400ST

R3609 11K

R3601 10K

R3613 11K

OPEN

R3608 33K

R3607 2K

C3609 10

R3612 12K

R3611 2K

C3613 10

R3619 82K

R3641 10K

R3625

R3624

20K

C3686 22P

C3634C3635

C3606 220/6.3V

C3611 220/6.3V

43K

R3626

1.5K

C3636

C3622

10

IC3601 BD00IA5WEFJ-E2 (+3.3V REG.)

1

VOUT

VCC

2

FB

NU

3

GND

NU

45

NU EN

IC3603 BD00IA5WEFJ-E2 (+1.8V REG.)

1

VOUT

VCC

2

FB

NU

3

GND

NU

45

NU EN

8

7

6

8

7

6

390 R3605

30

R3604 680

D3606 OPEN

R3623 OPEN

C3602 10

C3612 OPEN

C3610 10

C3687 OPEN

C360510C3608 D3609 220/6.3V

R3649

R3645

OPEN

R3644

0.47

R3610 100

R3646 100

R3643

0.47

R3617 1

MM5Z4V3B

R3141 22K

Q3106 2SC4081UBTLQ

D3101 OPEN

L3107 22uH

L3106 22uH

L3116 22uH

L3102 22uH

L3103 22uH

C3182 10

R3197 33K

C3132

0.1

Q3105 2SA1576UBTLQ

(SWITCHING)

R3143 10K

R3150 22K

C3109 10

C3130 10

R3189 33K

R3161 100

C3158 10

C3183

0.1

C3160

0.1

C3184

0.1

C3108

0.1

C3129

0.1

C3127

0.1

Q3103 2SA1576UBTLQ

(SWITCHING)

C318510C3180

0.1

R3108 2K

R3140 OPEN

R3142 1K

D3140 OPEN

R3145 10K

R3160 10K

R3162 100

R3188 OPEN

C3156

0.1

C3131

0.1

L3101 22uH

C3175 OPEN

C3181

0.1

C3151

0.1

R3133 10K

R3159 10K

1KR3199

C3112

0.1

C3176

0.1

R3101 10

10KR3191

10C3123

0.1C3133

22R3106

R3004 10K

R3002

4.7K

*1

IC3101(4/4) MSD8220LB1-S1

DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

21

ADD-ADC33

33 AVDD-AU33

51 AVDD3P3-DADC

52 AVDD-DMPLL

5 AVDD-MOD33-1 55 AVDD-MOD33-2 87 AVDD-MOD33-3 127 AVDD-MOD33-4

32 VDDC-1 57 VDDC-2 131 VDDC-3 144 VDDC-4

104 PROTECT3

101 BACKLIGHT-SW

56 VDDIO-CMD 132 VDDIO-DATA

133 P-ON-H2

27 VSYNC1

42 AUVAG

43 AUREFM

129 PROTECT1

121 CELL-PWR-CTRL 109 VCOM-PWM

63 AMP-MUTE 98 HP-MUTE

110 BACKLIGHT-ADJ

118 GND 143 GND

*A NU

*A:28,29,31,36~41,92~97, 106,125,126,138

S

TWVU

10-16

X

PL14.22BSCD4

Function Schematic Diagram

FUNCTION CBA UNIT

2

1

TO IR SENSOR CBA UNIT CN4051

CN4001 1GND

2KEY-IN1

C4002

0.1

D4001 MM5Z5V6B

R4006

2.2K

SW4007

POWER

D4002 OPEN

R4005

2.2K

SW4006 SW4005 SW4004 SW4003 SW4002 SW4001

R4004

2.7K

MENUSOURCE

R4003

4.7K

CH UP

R4002

8.2K

CH DOWN

R4001 18K

VOL UP

VOL DOWN

UNLESS OTHERWISE SPECIFIED: SWITCHES ARE SKRMABE010.

ABC

10-17

PL14.22SCF

IR Sensor Schematic Diagram

RS4051 RS-272

(REMOTE SENSOR)

V-OUT

231

GND

Vcc

R4060 OPEN

R4053 15K

D4051 SMLE12WBC7W1HR

POWER

C4054

0.1

2

1

TO FUNCTION CBA UNIT CN4001

CN4051 1GND

2KEY-IN1

R4051 56

C4051 10

C4056 10

R4052

6.8K

C4052 1000P

R4057 360K

C4057

0.1

C4053

0.1

IC4051 BH1603FVC-TR

(LIGHT SENSOR)

IOUT

1

2

34

GC2

GND

GC1

VCC NU

6

5

R4055 10K

R4058 OPEN

R4054 1K

R4059 OPEN

R4056 10K

C4055 OPEN

CN4052

1 AL+3.3V 2 P-ON+5V 3 LIGHT 4 LED1 5 REMOTE 6 KEY-IN1 7 GND 8 SCL(NU) 9 SDA(NU)

TO DIGITAL MAIN CBA UNIT CN3101 or CN3105

IR SENSOR CBA UNIT

ABC

10-18

PL14.22SCIR

Power Supply CBA Top View

CAUTION !

Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F602) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

A

B

C

J1216

JS1135

J1272

J1211

J1212

D

E

J1213

J101

J102

J1416

J1413

Protect3

J1317

Protect3

JS1235

GND

BL-ADJ

BL-SW

Protect3

Outer GND

CN1101

GND

J1313

J1312

BL-SW J1311

GND

GP002

GND

BL-ADJ

J1116

GP001

1

J1410

J1411

J1412

BL-SW

BL-ADJ

TOP SIDE

J1316

SPWM3

J1273

J1274

J1215

J1210

ADIM2

SPWM2

ADIM1

AMP+13V

CN1301

J1415

J1302

GND

J1202

J1306

J1315

SPWM3

J1214

ADIM4

SPWM4

Vcc2

GND

J1269

J1102

AMP+13V

J1402

GND

J1314

ADIM3

J1204

Q1201 Gate

R1215

OVP2

J1114

J1406

J1106

J1304

OVP3

Vcc1

Vcc4

J1404

OVP4

J1303

Vcc3

Q1301 Gate

R1315

J1203

J1206

J1104

Q1101 Gate

R1115

OVP1

23

CN1401

CN501

L1401

Gate

Q1401

J1403

J1401

D1401

J1405

D1201 Vout

D1301

D1101 Vout

UVLO3

L1201

UVLO2

J1205

UVLO1

J1105

D1401 Vout

J1301

UVLO4

D1301 Vout

C1117

VLED2

J1207

J1107

VLED1

C1317

J1208

D1201

R1415

J1305

J1201

J1103

D1101

J1101

LED+48V

C1217

J1109

ILED1

LED+48V

GND

J704

J1108

C723

J1308

C1203

L1101

C1103

LED+48V

VLED3

GND

J703

J1309 ILED3

J1307

C1417

C1303

D711

J653

J1407

VLED4

GND

AMP+13V

J652

C1403

L1301

J665

D710

AMP+13V

P-ON+21V

J651

C657

C651

D712

C725

C724

2.5A 250V

AMP+13V

C728

D654

D658

C655

C654

D650

C650

D713

D704

C726

J701

LED+48V

J103

Outer GND

CAUTION ! :

For continued protection against risk of fire, replace only with same type 2.5A, 250V fuse.

ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.

BA4GU5F0102 1

P-ON+21V

J655

ALL+3.3V

D715

J654

D715 Reference

D655

D652

C652

T1701

J702

D704 Cathode

D653

D656

C656

GP003

D650

AMP+13V

J663

J666

J658

J657

Anode

IC1702

C1711

J656 J664

Q701 Base

P-ON H2

Q702 Base

J659

T601

R1719

C692

D660

D660 Cathode

C619

J1703

IC1701 Out

IC1701 FB

IC1701 Vcc

J1704

C1709

TOOL NO. 1 2 3 4 5 6 7 8 9 10

J662

J1611

Vcc+15V

C1708

J1614

Vcc+15V

J1253

J1701

J1702

Q1701 Collector

465

J660

J661

AMP+13V

P-ON+21V

IC602

D664

PFC Vout

J603

J1705

D1707

PFC GND

Q1704

CAUTION -

RISK OF FIRE REPLACE FUSE AS MARKED

J1271

FB

IC1602

IC601

J1617

J606

Vcc+15V

C615

D621

D619

BC602

C606

R618

C665

C605

C1621

PFC Vout

J604

J1613

PFC Vout

J1612

PFC Vout

J1620

D1714 Cathode

C1614

D1714

BC1703

C1706

J1619

Vcc+15V

J1610

Vcc+15V

D620

D607

D613

J1603

C1618

C1602

D605

C1726

D1605

GDB

COLD

J1618

Drive

C616

C602

VSENSE

SA601

IC601 Vcc

D606

D1603

J607

J601

C1612

R1624

C1626

J1609

Pri GND

COMP

T 2.5A L/250V

F602

R601

J602

IC601 FB

IC604

IC601 ZCD

C620

J605

PFC

GND

IC601 FB

J609

J1601

T1601

J1605

J1615

D603

Vin

PFC

C1613

ZCDB

ILED2

LIVE

J610

IC601 VH

IC601 ZCD

J608

BC1602

PFC Vin

J1602

C1615

J1607

J1616

J1209

VREF

Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required.

NOTE:

The voltage for parts in hot circuit is measured using hot GND as a common terminal.

CN601

NEUTRAL

C604

L602

C614

L601

D604

BC1601

D602

D601

J1608

GDA

T1602

J1604

J1268

Pri

GND

GP004

UNDER SIDE

C1707

10-19

BA4GU5F01021

Power Supply CBA Bottom View

CAUTION !

Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F602) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

65

C625

D1603

C1608

C612

R603

D618

D617

R608

R605

R604

D606

R624

R1611

SA601

R633

C616

D611

R1607

J1618

R632

R635

D615

R610

D605

C602

C1726

D1605

R1622

D1610

R1614

D601

R1613

C1707

C604

D602

R1612

R1615

R1616

GP004

D604

R1623

BC1601

R1621

J1604

R1626

T1602

CN601

L602

J1268

C614

L601

C621

J610

VH

BC1602

C1603

R627

R623

IC601

C1615

J1608

C1607

IC601ZCD

R626

D603

Q1602

R1610

R620

C611

C610

J608

J1602

R1630

J1616

J1209

Q603

D623

C620

R625

J1607

F602

C622

R607

C1613

R1606

R1645

IC604

IC601

R614

J1601

R1627

R1654

R1655

C624

T1601

C1609

J1615

C1610

R629

J605

R634

C607

J602

R628

J609

R611

J1605

R601

J601

R1624

C1626

D614

D609A

C608

C1612

R613

J607

R609

J1609

IC1601

R617

D1608

Q602

R1625

C1611

R1609

C1618

R1657

D620A

C1605

D613

C1601

R1608

C1602

D620

D607

C1604

R619

J1603

R1653

C1606

Q601

R1605

R1637 R1639

D613A

Q1601

R1629

C1614

J1610

R1604

Q1607

R1602

R1634

D621A

BC602

R618

D621

C606

2.5A 250V

R1656

J1271

R1638

J1617

Q1604

J606

Vcc+15V

C615

D619

D619A

R606

C605

C1621

J1613

J1612

J1620

D1714

BC1703

C1706

J1619

R1601

R1617

R1620

R1619

IC1602

C665

R1618

J604

CAUTION ! :

For continued protection against risk of fire, replace only with same type 2.5A, 250V fuse.

ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.

J660

BA4GU5F0102 1

R630

J603

IC602

R1746

R1714

Q1704

R1712

R631

R1747

D1714A

R1718

D1705A

R657

R1633

D1710

D1707

R1711

J661

D664A

R655

D664

J1705

R659

D1707A

C1710

R1710

R654

Q691

R675

C660

R1704

R1707

D663

J1614

C1703

R1702

Q1702

C1708

R1703

J1253

J1702

R1705

R658

R693

R674

J662

R1720

J1703

R1708

C691

R667

R691

R660

J1611

R1709

C692

J1701

D662

D661

R661

C1704

R692

C1702

C701

C619

D1704

R1701

R703

Q701

D660

R668

J1704

R653

IC1701

R1

C1701

C1709

R701

J659

R702

Q653

71

Q1701

R749

Q702

9

Q650

R750

R669

R752

T601

R656

J656 J664

R704

IC1702

J658

C1711

R652

J657

J663

D657

J666

Q654

C729

R651

R751

D656A

R755

R662

D653

D656

C656

R738

D715

R754

D652A

R739

D655

D652

GP003

D1711

R741

R743

J654

J702

J655

C722

R663

34

R753

1

R745

D704

Q705

T170

D713

C652

Q703

R748

J103

D658

D650

C728

R744

J701

D654A

C655

R740

R756

C637

C721

D654

C650

C726

D716

C657

C654

C639

C651

C724

R1423

D713A

J651

R1424

J665

C725

C638

C1403

J1407

C1414

D710

J652

C1415

C1417

D712

C1004

C1401

C1416

C1201

D711

J653

J1309

L1301

J1307

R1224

C1402

R1427

J1308

C1303

C1202

C1214

R1401

R1402R1403

C1215

R1118

C1109

R1407

C1404

C1112

J1108

R1410

R1406

D1303

J703

C1217

CN501

J704

J1208

C1203

J1109

L1101

C1101

C1103

C723

D1404

C1301

C1317

J1207

J1107

R1324

C1117

D1403

R1101

L1401

D1401A

R1422

D1301A

R1323

D1101A

R1124

R1123

L1402

C1302

R1322

J1403

J1401

J1405

L1302

J1301

D1305

R1223

2

D1401

D1405

R1301

C1114

R1122

R1222

J1205

L1102

C1102

J1105

R1425

D1304

L1201

CN1401

Q1401

C1408

R1417

R1415

R1426

D

13 01

C1314

D1201A

R1201

D1205

J1103

C1115

D1105

R1416

R1325

J1305

J1101

D1104

J1201

D1204

D1101

R1405

R1418

C1409

R1225

R1226

Q1101

C1108

R1117

C1308

C1315

J1203

R1125

R1404

R1326

R1317

C1316

L1202

D1201

C1208

C1216

J1206

R1116

C1116

R1413

C1412

C1405

Q1301

J1303

R1327

R1316

R1217

R1127

R1103

R1126

D1306

R1303

R1102

D1406

J1404

IC1401

R1313

R1315

C1309

C1305

C1304

R1302

Q1201

R1227

C1204

R1202

J1104

D1103

Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required.

NOTE:

The voltage for parts in hot circuit is measured using hot GND as a common terminal.

1

R1220

R1211

J1215

J1273

J1411

R1329

R1308

J1316

Q1203

R1212

C1211

C1220

R1111

R1331

C1207

R1209

R1112

J1412

CN1101

C1310

C1311

C1320

J1313

C1206

C1120

R1133

R1419

R1332

C1307

J1312

J1311

JS1235

R1229

Q1103

R1121

C1107

C1410

J1413

R1330

J1317

R1309

J1116

R1109

GP002

C1411

J1416

R1411

C1306

C1106

GP001

R1432

R1412

C1407

R1232

R1132

C1420

C1406

JS1135

J1213

A

R1409

B

C

R1230

R1231

R1219

J1216

J1272

J1211

J1212

R1129

R1108

R1408

R1221

C1210

D

R1131

J102

R1130

J101

Q1403

J1406

R1216

R1207

D1102

R1115

J1106

D1402

J1402

C1312

R1310

C1104

R1106

R1428

R1305

J1304

R1307

R1306

C1209

R1203

R1210

R1107

C1413

R1304

R1318

IC1301

J1204

R1215

C1212

C1205

D1106

R1113

J1269

IC1101

J1102

C1105

R1110

D1302

J1314

J1306

D1206

R1213

J1114

CN1301

R1430

R1421

R1420

R1433

R1328

J1302

R1205

D1202

R1218

J1202

R1105

R1128

J1410

J1315

J1210

J1214

IC1201

R1206

D1203

C1113

R1120

R1429

J1415

C1313

R1312

C1110

R1119

R1321

R1319

R1233

C1111

R1333

R1104

R1431

Q1303

R1320

R1311

R1335

R1204

R1228

C1213

R1208

J1274

E

10-20

BA4GU5F01021

[TYPE A]

WIRING DIAGRAMS

1

CN4001

1

CN4051

9

CN4052

1

CN3105

FUNCTION CBA UNIT

CL4051

IR SENSOR CBA UNIT

CL3101

AC CORD

2

1

9

CN601

BW

CN501

CN3601

1

POWER SUPPLY CBA

CL501

CN1301

12

LCD PANEL ASSEMBLY

CN1101

14

23

CL3013

23

1

CN3906

51

SP3802

SPEAKER

SP3801

SPEAKER

R-CH

L-CH

CL3801

CN3801

14

TUNER UNIT

COMPONENT

-Y/VIDEO-IN

COMPONENT

-Pb-IN

COMPONENT

-Pr-IN

AUDIO(L)-IN

REAR

AUDIO(R)-IN

DIGITAL

DIGITAL MAIN CBA UNIT

AUDIO-OUT

(COAXIAL)

ETHERNET

JACK

HDMI-

CONNECTOR-1

HDMI-

CONNECTOR-2

HDMI-

CONNECTOR-3

PC-RGB-IN

SIDE

WIRELESS

LAN MODULE

USB JACK

PL14.22AWI11-1

HEADPHONE

JACK

[TYPE B]

1

CN4001

1

CN4051

9

CN4052

1

CN3101

FUNCTION CBA UNIT

CL4051

IR SENSOR CBA UNIT

CL3101

AC CORD

2

1

9

CN601

BW

CN501

CN3602

23

1

POWER SUPPLY CBA

CL501

CN1301

12

LCD PANEL ASSEMBLY

CN1101

14

1

CL3013

23

1

CN3013

51

SP3802

SPEAKER

SP3801

SPEAKER

R-CH

L-CH

CL3801

CN3801

14

TUNER UNIT

COMPONENT

-Y/VIDEO-IN

COMPONENT

-Pb-IN

COMPONENT

-Pr-IN

AUDIO(L)-IN

REAR

AUDIO(R)-IN

DIGITAL

11-2

DIGITAL MAIN CBA UNIT

AUDIO-OUT

(COAXIAL)

HDMI-

CONNECTOR-1

HDMI-

CONNECTOR-2

HDMI-

CONNECTOR-3

PC-RGB-IN

SIDE

USB JACK

HEADPHONE

JACK

PL14.22BWI

[TYPE A]

B31

A15

See Electrical Parts List for parts with this mark.

Digital Main CBA Unit

Power Supply CBA

Function CBA Unit

A17

B12

L23

A26

B18

L10

L28

X6

S7

L28

L45

A13

L23

B23

B10

L10

L28

IR Sensor CBA Unit

A26

A16

SSK1

SNA1

SBA1

A3-2

A8

A7

SP3802

CL3801

CL4051

CL3101

CL501

SP3801

B7

A3-1

A5

A9

A20

L23

49PFL4909/F7, 49PFL4909/F8

49PFL4909/F7, 49PFL4609/F7

49PFL4609/F7

CL3013

AC601

LCD1

B23

L35

B19

L23

B17

B18

B17

B18

B17

B18

B17

L45

SSK1

SNA1

SBA1

EXPLODED VIEWS

12-1 PL14.22-A_CEX

[TYPE B]

A15

See Electrical Parts List for parts with this mark.

Digital Main CBA Unit

Power Supply CBA

Function CBA Unit

B12

B31

L23

A26

B18

L10

L28

X6

S7

L28

L45

A13

L23

B23

B10

L10

L28

IR Sensor CBA Unit

A26

A16

SSK1

SNA1

SBA1

A3-2

A8

A7

SP3802

CL3801

CL4051

CL3101

CL501

SP3801

B7

A3-1

A5

A9

A20

L23

CL3013

AC601

LCD1

B23

L35

B19

L23

B17

B18

B17

B18

B17

B18

B17

L45

SSK1

12-2 PL14.22-B_CEX

Packing

Some Ref. Numbers are not in sequence.

S1

SSK1 X4 X3

S7

S12

S7

X22

X2 X14

S3

S4

S6

Fixlon Tape

Packing Tape

X1

SBA1

SNA1

Tape

*1: 49PFL4909/F7, 49PFL4709/F8, 49PFL4909/F8 *2: 49PFL4609/F7

49PFL4709/F8, 49PFL4909/F8

S10

*2

*1

*2

*1

REAR SIDE

SNA1

49PFL4909/F8

12-3 PL14.22-A_PEX

TYPE A

PARTS LIST [49PFL4909/F7 (Serial No.: DS1)]

Mechanical Parts

PRODUCT SAFETY NOTE: Products marked with a

# have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTE: Parts that are not assigned part numbers (---------) are not available.

Ref. No. Description Part No.

A3-1 REAR CABINET L A4D1BUH 2EMM00271B

A3-2 REAR CABINET R A4D1BUH 2EMM00272B

A5 DECORATION PLATE A4D1BUH 2EMH00289

A7 FUNCTION KNOB A4GF1UT 2EMM00237

A8 KNOB FRAME A4DFAUT 2EMM00325

A9 LED LENS A4DFAUT 2EMM00301A

A13 JACK HOLDER A3RF0UT 1EM334677

A15# RATING LABEL A4D17UH ----------

A16 LOGO LABEL A4DFAUT ----------

A17 ENERGY GUIDE LABEL A4D1EUH ----------

A20 LEADING EDGE COVER A4D1BUH 2EMM00294

A26 SPEAKER HOLDER A4GU0UT 2EMM00248

AC601# AC CORD W/O A GND WIRE UL/CSA/1775/NO/

B7 T-CON HOLDER A4D1BUH 2EMS00151A

B10 STAND BRACKET A4D1BUH 2EMS00148A

B12 SENSOR SHIELD A4GF1UT 2EMS00133

B17 WALL MOUNT BRACKET A4GU0UT 2EMS00136

B18 WALL MOUNT COVER A4GU0UT 2EMM00263

B23 WIRE LABEL A3AF0UT ----------

B31 BLIND LABEL A4D1BUH ----------

CL501 FFC WIRE ASSEMBLY 23PIN 23PIN/WHITE/

CL3013 FFC WIRE ASSEMBLY 51PIN(W/SHIELD) 51P/

CL3101 FFC WIRE ASSEMBLY 9PIN 9PIN/WHITE/

CL3801 WIRE ASSEMBLY 4PIN 4PIN/180MM&740MM WX1A4GU5C502

CL4051 WIRE ASSEMBLY 2PIN 2PIN/525MM WX1A4D1BC301

L10 SCREW F-PAN BLACK_NI +P-TITE M3X12.0

L23 SCREW BIND 3CHROM +S-TITE M3X6.0 M3X6

L28 SCREW F-PAN BLACK_NI +S-TITE M3X8.0 3X8

L45 SEMS-SW PAN BLACK_NI + M4X10.0 M4X10 +

SBA1 STAND BASE ASSEMBLY A4D17UH 2EMA00059

SNA1 STAND NECK A4D17UH 2EMZ00151

SP3801 SPEAKER MAGNETIC 8OHM/10W S0411F19 DS08110XQ004

SP3802 SPEAKER MAGNETIC 8OHM/10W S0411F19 DS08110XQ004

SSK1 STAND SCREW KIT A3AU0UH(SEMS-SW PAN

BLACK

364MM

FFC/SHIELD/589MM

620MM

3X12 WASHER HEAD+BLK

BIND HEAD+

WASHER HEAD+BLAC

BLK

BLACK_NI + M4X12.0)

PAC K IN G

S1 CARTON A4D17UH 2EMC00356

S3 STYROFOAM TOP A4D1BUH 2EMC00303

S4 STYROFOAM BOTTOM A4D1BUH 2EMC00304

WAC172LTE010

WX1A4D1BS201

WX1A4D1BT402

WX1A4GU5S302

GCHP3120

GBJS3060

GCHS3080

FPH34100

1ESA34506

Ref. No. Description Part No.

S6 SET BAG A3AUCUH 2EMC00085

S7 SERIAL NO. LABEL A4GF1UT ----------

S10 PROTECTION CARTON A4D1BUH 2EMC00321B

ACCESSORIES

X1 POLYETHYLENE BAG HDPE 180X340XT0.03 1EM435579

X2# OWNERS MANUAL A4D1BUH 2EMN00154C

X3 REMOTE CONTROL UNIT YKF340-003 URMT41JHG003

X4 BATTERY DRY R03(SIZE AAA ) XB00M0RKT001

X6 QUICK START GUIDE A4D17UH 2EMN00176B

X22 WARNING MESSAGE FLIER A3AU2UH 2EMN00059A

LCD PANEL ASSEMBLY

Ref. No. Description Part No.

LCD1# LCD PANEL ASSEMBLY U4D10P0

LCD MODULE ----------

2015/06/08 13-1 A4D17_CA.fm

Electrical Parts

PRODUCT SAFETY NOTE: Products marked with a

# have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTES:

1. Parts that are not assigned part numbers (---------) are not available.

2. Tolerance of Capacitors and Resistors are noted with the following symbols.

C.....±0.25% D.....±0.5% F.....±1%

G.....±2% J......±5% K.....±10%

M.....±20% N.....±30% Z.....+80/-20%

DIGITAL MAIN CBA UNIT

Ref. No. Description Part No.

DIGITAL MAIN CBA UNIT A4D17MMA-006

CN3701 WIRELESS LAN MODULE WM5504 UWLMDLACM002

IC3101 IC MAIN PH1-SLD8PLUS MN2WS0270HA QSCA0R0MS065

IC3102 IC NAND FLASH 1GB H27U1G8F2BTR-BC NSCA0R0HY009

IC3103 16KBIT EEPROM M24C16-WMN6TP NSZBA0TSS259

IC3601 IC RESET IC-PST8429UR QSCA0T0MM075

IC3602 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021

IC3603 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021

IC3604 IC DCDC CONVERTER RT8293ALZSP NSCA0T00B017

IC3607 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021

IC3701 IC USB HIGH-SIDE SW AP2151WG-7/SOT25/

IC3803 IC D-CLASS AUDIO POWER AMPLIFI

IC3901 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021

TU3001 TUNER UNIT U9004UH U9004UH

IC3401 IC 1GB DDR3 SDRAM K4B1G1646G-BCK0 NSCA0R0SM055

IC3402 IC 2GB DDR3 SDRAM K4B2G1646Q-BCMA NSCA0R0SM057

IC3401 IC 1GB DDR3 SDRAM H5TQ1G63EFR-PBC NSCA0R0HY039

IC3402 IC 2GB DDR3 SDRAM H5TQ2G63FFR-PBC NSCA0R0HY041

IC3401 IC 1GB DDR3 SDRAM NT5CB64M16FP-DH NSCA0R0J2017

IC3402 IC 2GB DDR3 SDRAM NT5CB128M16FP-DI NSCA0R0J2016

5PI

TPA3110D2PWPR

When you replace one of the below ICs on this CBA, always replace the IC in accordance with the 3 combinations below. Do not mix ICs of different combination.

or

NSCA0TDES015

NSCA0T0TY073

MSW ASSEMBLY

Ref. No. Description Part No.

MSW ASSEMBLY Consists fo the following

FUNCTION CBA UNIT A4D1BMSW-001-FN

IR SENSOR CBA UNIT A4D1BMSW-001-IR

IC4051 O-E DEVICE LIGHT SENSOR BH1603FVC-

TR /WSOF6

A4D1BMSW-001

QP2Z00BH1603

POWER SUPPLY CBA

Ref. No. Description Part No.

POWER SUPPLY CBA Consists fo the following

CAPACITORS

C602 CAP METALLIZED FILM 0.1µF/310V /K/LE-MX CTA1040DC001

C604# CAP METALLIZED FILM 0.1µF/310V /K/LE-MX CTA1040DC001

C605 CAP ELE 33µF/400V/M/85 CEN3300V8007

C606 CERAMIC CAP. RB 220pF/2kV CA3D221TE006

C607 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102

C608 CHIP CERAMIC CAP. CH J 150pF/50V CHD1JJ3CH151

C610 CHIP CERAMIC CAP. B K 220pF/50V CHD1JK30B221

C611 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C612 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102

C614# CAP METALLIZED FILM 1.0µF/310V /K/LE-MX CTA1050DC001

C615 CAP ELE 47µF/50V/M/85 CEF4700V8006

C616 CAP ELE 220µF/35V/M/85 CEE2210V8006

C619# CAP CERAMIC SAFETY 1000pF/250V E M KX CJMR102M42E1

C620 CAP ELE 33µF/35V/M/85 CEE3300V8006

C621 CHIP CERAMIC CAP.(1608) B K 4700pF/50V CHD1JK30B472

C622 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102

C624 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C625 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102

C650 CERAMIC CAP. /_1 B K 2200pF/1kV CJTE222KB3A5

C651 CAP ELE 470µF/25V/M/85 CED4710V8006

C652 CAP ELE 470µF/25V/M/85 CED4710V8006

C654 CAP ELE 470µF/16V/M/85 CEC4710V8006

C655 CAP ELE 470µF/16V/M/85 CEC4710V8006

C656 CAP ELE 1µF/50V/M/85 CEF1R00V8006

C660 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C665 CERAMIC CAP. RB 680pF/2kV CA3D681TE006

C691 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103

C692 CAP ELE 33µF/35V/M/85 CEE3300V8006

C721 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C722 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C723 CAP ELE 470µF/63V/M/85 CEG4710V8007

C724 CAP ELE 470µF/63V/M/85 CEG4710V8007

C725 CERAMIC CAP. /_1 B K 2200pF/1kV CJTE222KB3A5

C726 CAP ELE 470µF/63V/M/85 CEG4710V8007

C728 CAP ELE 100µF/10V/M/85 CEB1010V8006

C729 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C1004 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080

C1101 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080

C1102 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080

C1103 CAP ELE 100µF/63V/M/85 CEG1010V8006

C1105 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105

C1106 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224

C1107 CHIP CERAMIC CAP.(1608) B K 0.047µF/25V CHD1EK30B473

C1108 CHIP CERAMIC CAP. B K 560pF/50V CHD1JK30B561

C1109 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102

C1110 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224

C1112 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105

C1113 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222

C1114 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080

C1116 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080

C1117 CAP ELE 100µF/100V/M/85 CEH1010V8007

C1201 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080

C1202 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080

C1203 CAP ELE 100µF/63V/M/85 CEG1010V8006

C1205 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105

A4D1BMPW-001

2015/06/08 13-2 A4D17_EL.fm

Ref. No. Description Part No.

C1206 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224

C1207 CHIP CERAMIC CAP.(1608) B K 0.047µF/25V CHD1EK30B473

C1208 CHIP CERAMIC CAP. B K 560pF/50V CHD1JK30B561

C1209 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102

C1210 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224

C1212 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105

C1213 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222

C1214 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080

C1216 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080

C1217 CAP ELE 100µF/100V/M/85 CEH1010V8007

C1301 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080

C1302 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080

C1303 CAP ELE 100µF/63V/M/85 CEG1010V8006

C1305 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105

C1306 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224

C1307 CHIP CERAMIC CAP.(1608) B K 0.047µF/25V CHD1EK30B473

C1308 CHIP CERAMIC CAP. B K 560pF/50V CHD1JK30B561

C1309 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102

C1310 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224

C1312 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105

C1313 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222

C1314 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080

C1316 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080

C1317 CAP ELE 100µF/100V/M/85 CEH1010V8007

C1601 CHIP CERAMIC CAP. B K 8200pF/50V CHD1JK30B822

C1602 CAP ELE 4.7µF/50V/M/85 CEF4R70V8006

C1603 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224

C1604 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225

C1605 CHIP CERAMIC CAP. B K 1200pF/50V CHD1JK30B122

C1606 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102

C1607 CHIP CERAMIC CAP. B K 1200pF/50V CHD1JK30B122

C1608 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102

C1609 CHIP CERAMIC CAP.(1608) CH J 22pF/50V CHD1JJ3CH220

C1610 CHIP CERAMIC CAP.(1608) CH J 22pF/50V CHD1JJ3CH220

C1611 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C1612# CAP METALLIZED FILM 0.47µF/310V /K/LE-MX CTA4740DC001

C1613 CERAMIC CAP. RB 220pF/2kV CA3D221TE006

C1614 CERAMIC CAP. RB 220pF/2kV CA3D221TE006

C1618 CAP ELE 10µF/50V/M/85 CEF1000V8006

C1621 CAP ELECTROLYTIC 100µF/400V/M/22/25 CA2H101DYG17

C1701 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102

C1702 CHIP CERAMIC CAP. CH J 150pF/50V CHD1JJ3CH151

C1703 CHIP CERAMIC CAP. B K 220pF/50V CHD1JK30B221

C1704 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104

C1706 CERAMIC CAP. RB 470pF/2kV CA3D471TE006

C1707# CAP CERAMIC SAFETY 1000pF/250V E M KX CJMR102M42E1

C1708 CAP ELE 33µF/400V/M/85 CEN3300V8007

C1709 CAP ELE 220µF/10V/M/85 CEB2210V8006

C1710 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102

C1726 CERAMIC CAP RB 1500pF/2kV CA3D152TE006

CONNECTORS

CN501 FFC CONNECTOR IMSA-9615S-23A-PP-A JC96J23ER007

CN601# CONNECTOR B2P3-VH(LF)(SN) J3VH020JG001

CN1101 CONNECTOR PRINT OSU JS-1125-04(K) J3JT04CHY001

CN1301 PH CONNECTOR TOP 2P B2B-PH-K-S

(LF)(SN)

J3PHC02JG029

DIODES

D601# DIODE 1N5406BH NDL1001N5406

D602# DIODE 1N5406BH NDL1001N5406

D603# DIODE 1N5406BH NDL1001N5406

D604# DIODE 1N5406BH NDL1001N5406

D605 RECTIFIER DIODE 1N4005 NDWZ001N4005

D606 RECTIFIER DIODE 1N4005 NDWZ001N4005

Ref. No. Description Part No.

D607 DIODE 1N5406BH NDL1001N5406

D609A DIODE SCHOTTKY SMD CES520.L3F(D QD1Z00CES520

D613 DIODE ZENER 1ZB36BB NDWZ0001ZB36

D614 ZENER DIODE SMD TFZVTR27B QD1B00TFZV27

D615 DIODE SWITCHING SMD 1SS400ST(SOD-523) ND1Z1SS400ST

D617 RES CHIP 1608 1/10W 0 W RRXA000HH014

D618 ZENER DIODE SMD TFZVTR18B QD1B00TFZV18

D619A DIODE FAST RECOVERY RS1GJTD ND1Z0RS1GJTD

D620A DIODE FAST RECOVERY RS1GJTD ND1Z0RS1GJTD

D621A DIODE FAST RECOVERY RS1GJTD ND1Z0RS1GJTD

D623 ZENER DIODE MM5Z5V6B ND1BMM5Z5V6B

D650 DIODE SHOTTKY SB3200BR NDWZ3200D027

D653 DIODE SCHOTTKY SB3150BH NDWZ00SB3150

D654 DIODE ZENER 1ZB20BB NDWZ0001ZB20

D655 DIODE SCHOTTKY SB3150BH NDWZ00SB3150

D656A DIODE FAST RECOVERY RS1GJTD ND1Z0RS1GJTD

D657 ZENER DIODE MM5Z4V3B ND1BMM5Z4V3B

D660 IC SHUNT REGULATOR SL431A-AT NSZBA0TAUK01

D661 DIODE SWITCHING SMD 1SS400ST(SOD-523) ND1Z1SS400ST

D662 DIODE SWITCHING SMD 1SS400ST(SOD-523) ND1Z1SS400ST

D663 DIODE SWITCHING SMD 1SS400ST(SOD-523) ND1Z1SS400ST

D664A DIODE FAST RECOVERY RS1KJTD ND1Z0RS1KJTD

D704 IC SHUNT REGULATOR SL431A-AT NSZBA0TAUK01

D710 DIODE SHOTTKY SB3200BR NDWZ3200D027

D711 DIODE SHOTTKY SB3200BR NDWZ3200D027

D712 DIODE SHOTTKY SB3200BR NDWZ3200D027

D715 IC SHUNT REGULATOR SL431A-AT NSZBA0TAUK01

D716 ZENER DIODE SMD TFZVTR4.7B QD1B0TFZV4R7

D1101 DIODE SCHOTTKY BARRIER SB2150BD NDWZ00SB2150

D1103 DIODE SWITCHING SMD 1SS400ST(SOD-523) ND1Z1SS400ST

D1104 ZENER DIODE SMD TFZVTR27B QD1B00TFZV27

D1105 ZENER DIODE SMD TFZVTR27B QD1B00TFZV27

D1201 DIODE SCHOTTKY BARRIER SB2150BD NDWZ00SB2150

D1203 DIODE SWITCHING SMD 1SS400ST(SOD-523) ND1Z1SS400ST

D1204 ZENER DIODE SMD TFZVTR27B QD1B00TFZV27

D1205 ZENER DIODE SMD TFZVTR27B QD1B00TFZV27

D1301 DIODE SCHOTTKY BARRIER SB2150BD NDWZ00SB2150

D1303 DIODE SWITCHING SMD 1SS400ST(SOD-523) ND1Z1SS400ST

D1304 ZENER DIODE SMD TFZVTR27B QD1B00TFZV27

D1305 ZENER DIODE SMD TFZVTR27B QD1B00TFZV27

D1603 DIODE FAST RECOVERY 30PFB60 QDWZ030PFB60

D1605 DIODE FAST RECOVERY 30PFB60 QDWZ030PFB60

D1608 ZENER DIODE SMD TFZVTR16B QD1B00TFZV16

D1705A DIODE SCHOTTKY SMD CES520.L3F(D QD1Z00CES520

D1707 DIODE ZENER 1ZB36BB NDWZ0001ZB36

D1711 ZENER DIODE SMD TFZVTR27B QD1B00TFZV27

D1714A DIODE FAST RECOVERY RS1KJTD ND1Z0RS1KJTD

ICS

IC601 IC SWITCHING FA5640N-C6-TE3/SOP-8 QSCA0T0FD007

IC602# O-E DEVICE PHOTO COUPLER

IC604 IC SHUNT REGULATOR SL431A-AT NSZBA0TAUK01

IC1101 IC LED BACKLIGHT CONTROLLER

IC1201 IC LED BACKLIGHT CONTROLLER

IC1301 IC LED BACKLIGHT CONTROLLER

IC1601 IC DUAL-PHASE PFC CONTROLLER

IC1602# O-E DEVICE PHOTO COUPLER

IC1701 IC SWITCHING FA5640N-C6-TE3/SOP-8 QSCA0T0FD007

IC1702# O-E DEVICE PHOTO COUPLER

TLP785F(D4FNBLLF(C

HA7223PE/SOP/16P

UCC28063DR/R-PDSO-G

TLP785F(D4FNBLLF(C

QPEL0TLP785F

NSCA0T00H007

NSCA0T0TY087

QPEL0TLP785F

2015/06/08 13-3 A4D17_EL.fm

Ref. No. Description Part No.

COILS

L601# LINE FILTER JLB24137 LLEG0Z0XB033

L602# LINE FILTER JLB24137 LLEG0Z0XB033

L1101 COIL POWER INDUCTORS DIP RP1315BNP-

L1102 COIL CHIP BEADS PZ2012D121-2R5T(F) LLF121SSN006

L1201 COIL POWER INDUCTORS DIP RP1315BNP-

L1202 COIL CHIP BEADS PZ2012D121-2R5T(F) LLF121SSN006

L1301 COIL POWER INDUCTORS DIP RP1315BNP-

L1302 COIL CHIP BEADS PZ2012D121-2R5T(F) LLF121SSN006

101M/100µH

LLF1010SF013

TRANSISTORS

Q601 MOS-FET 3.5A/600V TK4P60DA(T6RSS-Q) QF2ZTK4P60DA

Q602 FET MOS TK3P50D RQ(S QF2Z0TK3P50D

Q603 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S

Q650 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S

Q653 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S

Q654 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S

Q691 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S

Q701 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S

Q702 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S

Q703 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S

Q705 TRANSISTOR 2SA1201-Y QQ1Y2SA1201C

Q1101 FET MOS SMD AP05N20GH-HF NF2ZP05N20GH

Q1103 FET MOS SMD AP18T10AGH-HF NF2Z18T10AGH

Q1201 FET MOS SMD AP05N20GH-HF NF2ZP05N20GH

Q1203 FET MOS SMD AP18T10AGH-HF NF2Z18T10AGH

Q1301 FET MOS SMD AP05N20GH-HF NF2ZP05N20GH

Q1303 FET MOS SMD AP18T10AGH-HF NF2Z18T10AGH

Q1601 FET MOS TK7P60W.RVQ(S QF2Z0TK7P60W

Q1602 FET MOS TK7P60W.RVQ(S QF2Z0TK7P60W

Q1604 NPN TRANSISTOR SMD 2SC5344SY NQZY2SC5344S

Q1607 PNP TRANSISTOR SMD 2SA1576UBTLQ QQ1Q2SA1576U

Q1701 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S

Q1702 PNP TRANSISTOR SMD 2SA1576UBTLQ QQ1Q2SA1576U

Q1704 FET MOS TK5A65D(STA4 A Q) QFEZTK5A65DQ

RESISTORS

R601# RES. CARBON FILM J 1/2W J 1.2M W RCX2125T1003

R604 RES CHIP 1608 1/10W F 2.70k W RTW2701HH008

R605 RES CHIP 1608 1/10W J 270 W RRXA271HH013

R606 RES CHIP 1608 1/10W J 22k W RRXA223HH013

R607 RES CHIP 1608 1/10W J 4.7k W RRXA472HH013

R608 RES CHIP 1608 1/10W J 22 W RRXA220HH013

R609 RES CHIP 1608 1/10W J 820k W RRXA824HH013

R610 RES CHIP 3216 1/4W J 15k W RRX4153HH034

R611 RES CHIP 3216 1/4W J 15k W RRX4153HH034

R614 RES CHIP 3216 1/4W J 15k W RRX4153HH034

R617 RES CHIP 3216 1/4W J 4.7k W RRX4472HH034

R618 METAL OXIDE FILM RES. 2W J 0.22 W RN02R22ZU001

R619 RES CHIP 1608 1/10W J 4.7 W RRXA4R7HH013

R620 RES CHIP 1608 1/10W J 47k W RRXA473HH013

R623 RES CHIP 1608 1/10W F 1.80k W RTW1801HH008

R624 RES CHIP 3216 1/4W F 510k W RTC5103YF004

R625 RES CHIP 3216 1/4W F 510k W RTC5103YF004

R626 RES CHIP 3216 1/4W F 510k W RTC5103YF004

R627 RES CHIP 1608 1/10W F 36.0k W RTW3602HH008

R628 RES CHIP 1608 1/10W J 22k W RRXA223HH013

R629 RES CHIP 1608 1/10W J 47k W RRXA473HH013

R630 RES CHIP 3216 1/4W J 560k W RRX4564HH034

R631 RES CHIP 3216 1/4W J 560k W RRX4564HH034

R632 RES CHIP 1608 1/10W J 1.2k W RRXA122HH013

R633 RES CHIP 1608 1/10W J 1.2k W RRXA122HH013

Ref. No. Description Part No.

R634 RES CHIP 1608 1/10W J 270 W RRXA271HH013

R635 RES CHIP 1608 1/10W J 1.2k W RRXA122HH013

R651 RES CHIP 1608 1/10W J 1.0 W RRXA1R0HH013

R652 RES CHIP 1608 1/10W J 10k W RRXA103HH013

R653 RES CHIP 1608 1/10W F 22.0k W RTW2202HH008

R654 RES CHIP 3216 1/4W J 180 W RRX4181HH034

R655 RES CHIP 3216 1/4W J 180 W RRX4181HH034

R656 RES CHIP 1608 1/10W J 8.2k W RRXA822HH013

R657 RES CHIP 3216 1/4W J 3.9k W RRX4392HH034

R658 RES CHIP 1608 1/10W J 2.7k W RRXA272HH013

R659 RES CHIP 1608 1/10W F 27.0k W RTW2702HH008

R660 RES CHIP 1608 1/10W F 3.90k W RTW3901HH008

R661 RES CHIP 1608 1/10W F 3.30k W RTW3301HH008

R662 RES CHIP 1608 1/10W J 47k W RRXA473HH013

R667 RES CHIP 1608 1/10W J 8.2k W RRXA822HH013

R668 RES CHIP 1608 1/10W J 47k W RRXA473HH013

R669 RES CHIP 1608 1/10W J 10k W RRXA103HH013

R674 RES CHIP 1608 1/10W 0 W RRXA000HH014

R675 RES CHIP 1608 1/10W F 68.0k W RTW6802HH008

R691 RES CHIP 1608 1/10W J 2.2k W RRXA222HH013

R692 RES CHIP 1608 1/10W J 330 W RRXA331HH013

R693 RES CHIP 1608 1/10W J 47k W RRXA473HH013

R701 RES CHIP 1608 1/10W J 10k W RRXA103HH013

R702 RES CHIP 1608 1/10W J 47k W RRXA473HH013

R703 RES CHIP 1608 1/10W J 10k W RRXA103HH013

R704 RES CHIP 1608 1/10W J 47k W RRXA473HH013

R738 RES CHIP 3216 1/4W J 330 W RRX4331HH034

R739 RES CHIP 3216 1/4W J 15k W RRX4153HH034

R740 RES CHIP 1608 1/10W F 20.0k W RTW2002HH008

R741 RES CHIP 3216 1/4W J 3.9k W RRX4392HH034

R743 RES CHIP 1608 1/10W F 51.0k W RTW5102HH008

R744 RES CHIP 1608 1/10W F 9.10k W RTW9101HH008

R745 RES CHIP 1608 1/10W F 3.30k W RTW3301HH008

R748 RES CHIP 1608 1/10W F 3.30k W RTW3301HH008

R749 RES CHIP 1608 1/10W J 270 W RRXA271HH013

R750 RES CHIP 1608 1/10W J 270 W RRXA271HH013

R751 RES CHIP 1608 1/10W J 270 W RRXA271HH013

R753 RES CHIP 1608 1/10W J 100 W RRXA101HH013

R754 RES CHIP 1608 1/10W F 10.0k W RTW1002HH008

R755 RES CHIP 1608 1/10W 0 W RRXA000HH014

R756 RES CHIP 1608 1/10W J 1.5 W RRXA1R5HH013

R1101 RES CHIP 1608 1/10W F 75.0k W RTW7502HH008

R1102 RES CHIP 1608 1/10W F 20.0k W RTW2002HH008

R1103 RES CHIP 1608 1/10W F 20.0k W RTW2002HH008

R1104 RES CHIP 1608 1/10W J 75 W RRXA750HH013

R1105 RES CHIP 1608 1/10W J 75 W RRXA750HH013

R1106 RES CHIP 1608 1/10W J 10k W RRXA103HH013

R1107 RES CHIP 1608 1/10W J 100k W RRXA104HH013

R1108 RES CHIP 1608 1/10W J 10k W RRXA103HH013

R1109 RES CHIP 1608 1/10W J 100k W RRXA104HH013

R1110 RES CHIP 1608 1/10W F 36.0k W RTW3602HH008

R1111 RES CHIP 1608 1/10W F 24.0k W RTW2402HH008

R1112 RES CHIP 1608 1/10W F 2.20k W RTW2201HH008

R1113 RES CHIP 1608 1/10W J 10 W RRXA100HH013

R1115 METALOXIDE RES 1W J 0.12W RNJR12PAK001

R1118 RES CHIP 1608 1/10W J 200 W RRXA201HH013

R1119 RES CHIP 1608 1/10W F 62.0k W RTW6202HH008

R1120 RES CHIP 1608 1/10W J 120 W RRXA121HH013

R1121 RES CHIP 1608 1/10W J 51 W RRXA510HH013

R1123 RES CHIP 1608 1/10W J 5.6k W RRXA562HH013

R1124 RES CHIP 1608 1/10W J 5.6k W RRXA562HH013

R1125 RES CHIP 1608 1/10W F 360k W RTW3603HH008

R1126 RES CHIP 1608 1/10W F 240k W RTW2403HH008

2015/06/08 13-4 A4D17_EL.fm

Ref. No. Description Part No.

R1127 RES CHIP 1608 1/10W F 20.0k W RTW2002HH008

R1128 RES CHIP 1608 1/10W J 1.0k W RRXA102HH013

R1129 RES CHIP 3216 1/4W F 0.62 W RTR620RYL007

R1130 RES CHIP 3216 1/4W F 0.56 W RTR560RYL007

R1131 RES CHIP 3216 1/4W F 0.56 W RTR560RYL007

R1132 RES CHIP 3216 1/4W 0 W RRX4000HH036

R1201 RES CHIP 1608 1/10W F 75.0k W RTW7502HH008

R1202 RES CHIP 1608 1/10W F 20.0k W RTW2002HH008

R1203 RES CHIP 1608 1/10W F 20.0k W RTW2002HH008

R1204 RES CHIP 1608 1/10W J 75 W RRXA750HH013

R1205 RES CHIP 1608 1/10W J 75 W RRXA750HH013

R1206 RES CHIP 1608 1/10W J 10k W RRXA103HH013

R1207 RES CHIP 1608 1/10W J 100k W RRXA104HH013

R1208 RES CHIP 1608 1/10W J 10k W RRXA103HH013

R1209 RES CHIP 1608 1/10W J 100k W RRXA104HH013

R1210 RES CHIP 1608 1/10W F 36.0k W RTW3602HH008

R1211 RES CHIP 1608 1/10W F 24.0k W RTW2402HH008

R1212 RES CHIP 1608 1/10W F 2.20k W RTW2201HH008

R1213 RES CHIP 1608 1/10W J 10 W RRXA100HH013

R1215 METALOXIDE RES 1W J 0.12W RNJR12PAK001

R1218 RES CHIP 1608 1/10W J 200 W RRXA201HH013

R1219 RES CHIP 1608 1/10W F 62.0k W RTW6202HH008

R1220 RES CHIP 1608 1/10W J 120 W RRXA121HH013

R1221 RES CHIP 1608 1/10W J 51 W RRXA510HH013

R1223 RES CHIP 1608 1/10W J 5.6k W RRXA562HH013

R1224 RES CHIP 1608 1/10W J 5.6k W RRXA562HH013

R1225 RES CHIP 1608 1/10W F 360k W RTW3603HH008

R1226 RES CHIP 1608 1/10W F 240k W RTW2403HH008

R1227 RES CHIP 1608 1/10W F 20.0k W RTW2002HH008

R1228 RES CHIP 1608 1/10W J 1.0k W RRXA102HH013

R1229 RES CHIP 3216 1/4W F 0.62 W RTR620RYL007

R1230 RES CHIP 3216 1/4W F 0.56 W RTR560RYL007

R1231 RES CHIP 3216 1/4W F 0.56 W RTR560RYL007

R1232 RES CHIP 3216 1/4W 0 W RRX4000HH036

R1301 RES CHIP 1608 1/10W F 75.0k W RTW7502HH008

R1302 RES CHIP 1608 1/10W F 20.0k W RTW2002HH008

R1303 RES CHIP 1608 1/10W F 20.0k W RTW2002HH008

R1304 RES CHIP 1608 1/10W J 75 W RRXA750HH013

R1305 RES CHIP 1608 1/10W J 75 W RRXA750HH013

R1306 RES CHIP 1608 1/10W J 10k W RRXA103HH013

R1307 RES CHIP 1608 1/10W J 100k W RRXA104HH013

R1308 RES CHIP 1608 1/10W J 10k W RRXA103HH013

R1309 RES CHIP 1608 1/10W J 100k W RRXA104HH013

R1310 RES CHIP 1608 1/10W F 36.0k W RTW3602HH008

R1311 RES CHIP 1608 1/10W F 24.0k W RTW2402HH008

R1312 RES CHIP 1608 1/10W F 2.20k W RTW2201HH008

R1313 RES CHIP 1608 1/10W J 10 W RRXA100HH013

R1315 METALOXIDE RES 1W J 0.12W RNJR12PAK001

R1318 RES CHIP 1608 1/10W J 200 W RRXA201HH013

R1319 RES CHIP 1608 1/10W F 62.0k W RTW6202HH008

R1320 RES CHIP 1608 1/10W J 120 W RRXA121HH013

R1321 RES CHIP 1608 1/10W J 51 W RRXA510HH013

R1323 RES CHIP 1608 1/10W J 5.6k W RRXA562HH013

R1324 RES CHIP 1608 1/10W J 5.6k W RRXA562HH013

R1325 RES CHIP 1608 1/10W F 360k W RTW3603HH008

R1326 RES CHIP 1608 1/10W F 240k W RTW2403HH008

R1327 RES CHIP 1608 1/10W F 20.0k W RTW2002HH008

R1328 RES CHIP 1608 1/10W J 1.0k W RRXA102HH013

R1329 RES CHIP 3216 1/4W F 0.62 W RTR620RYL007

R1330 RES CHIP 3216 1/4W F 0.56 W RTR560RYL007

R1331 RES CHIP 3216 1/4W F 0.56 W RTR560RYL007

R1332 RES CHIP 3216 1/4W 0 W RRX4000HH036

R1601 RES CHIP 3216 1/4W F 750k W RTC7503YF004

Ref. No. Description Part No.

R1602 RES CHIP 3216 1/4W F 750k W RTC7503YF004

R1604 RES CHIP 3216 1/4W F 750k W RTC7503YF004

R1605 RES CHIP 3216 1/4W F 750k W RTC7503YF004

R1606 RES CHIP 1608 1/10W J 120k W RRXA124HH013

R1607 RES CHIP 1608 1/10W F 220 W RTW2200HH008

R1608 RES CHIP 1608 1/10W F 51.0k W RTW5102HH008

R1609 RES CHIP 1608 1/10W J 5.6k W RRXA562HH013

R1610 RES CHIP 1608 1/10W F 18.0k W RTW1802HH008

R1611 RES CHIP 1608 1/10W J 100 W RRXA101HH013

R1612 RES CHIP 3216 1/4W F 750k W RTC7503YF004

R1613 RES CHIP 3216 1/4W F 750k W RTC7503YF004

R1614 RES CHIP 3216 1/4W F 750k W RTC7503YF004

R1615 RES CHIP 3216 1/4W F 750k W RTC7503YF004

R1616 RES CHIP 1608 1/10W F 47.0k W RTW4702HH008

R1617 RES CHIP 3216 1/4W F 750k W RTC7503YF004

R1618 RES CHIP 3216 1/4W F 750k W RTC7503YF004

R1619 RES CHIP 3216 1/4W F 750k W RTC7503YF004

R1620 RES CHIP 3216 1/4W F 750k W RTC7503YF004

R1621 RES CHIP 1608 1/10W F 1.80k W RTW1801HH008

R1622 RES CHIP 1608 1/10W J 18k W RRXA183HH013

R1623 RES CHIP 1608 1/10W J 12k W RRXA123HH013

R1624 RES CEMENT 5W J 0.033 W RWJL33PAK002

R1625 RES CHIP 3216 1/4W J 47 W RRX4470HH034

R1626 RES CHIP 3216 1/4W J 47 W RRX4470HH034

R1627 RES CHIP 1608 1/10W J 12k W RRXA123HH013

R1633 RES CHIP 3216 1/4W J 2.7k W RRX4272HH034

R1634 RES CHIP 3216 1/4W J 47 W RRX4470HH034

R1637 RES CHIP 3216 1/4W J 180 W RRX4181HH034

R1638 RES CHIP 1608 1/10W J 18k W RRXA183HH013

R1639 RES CHIP 1608 1/10W J 10k W RRXA103HH013

R1645 RES CHIP 1608 1/10W F 68.0k W RTW6802HH008

R1653 RES CHIP 1608 1/10W J 68 W RRXA680HH013

R1656 RES CHIP 1608 1/10W J 4.7 W RRXA4R7HH013

R1657 RES CHIP 3216 1/4W J 2.7k W RRX4272HH034

R1702 RES CHIP 1608 1/10W F 2.70k W RTW2701HH008

R1703 RES CHIP 1608 1/10W J 4.7k W RRXA472HH013

R1704 RES CHIP 1608 1/10W J 22k W RRXA223HH013

R1705 RES CHIP 1608 1/10W J 27k W RRXA273HH013

R1707 RES CHIP 1608 1/10W J 820k W RRXA824HH013

R1708 RES CHIP 1608 1/10W J 22k W RRXA223HH013

R1710 RES CHIP 1608 1/10W J 22k W RRXA223HH013

R1711 RES CHIP 1608 1/10W J 10k W RRXA103HH013

R1712 RES CHIP 1608 1/10W J 180 W RRXA181HH013

R1714 RES CHIP 1608 1/10W J 22 W RRXA220HH013

R1718 RES CHIP 3216 1/4W J 22k W RRX4223HH034

R1719 METALOXIDE RES 2W J 0.12W RNJR12PAK002

R1720 RES CHIP 1608 1/10W J 270 W RRXA271HH013

R1746 RES CHIP 3216 1/4W J 270k W RRX4274HH034

R1747 RES CHIP 3216 1/4W J 270k W RRX4274HH034

MISCELLANEOUS

B19 POW HEAT SINK A7120UH 1EM423993A

BC602 BEAD INDUCTORS B29 RID 2.3X7.5X7.5T LLEF0S0XM002

BC1601 WIRE CP STP-S-0.50 XZ40F0REN001

BC1602 WIRE CP STP-S-0.50 XZ40F0REN001

BC1703 BEAD INDUCTORS B29 RID 2.3X7.5X7.5T LLEF0S0XM002

F602# FUSE TIME RAG SLT250V2.5A PDGSLB0NG252

L35 SCREW BIND 3CHROM +B-TITE M3X8.0 D3X8

SA601# VARISTOR 10D 471K SVR NVQZVR10D471

T601# TRANS POWER BCK-28IS LTT2PCMEK071

T1601# COIL EF TE2520A7001 LLEE0ZMEK005

T1602# COIL EF TE2520A7001 LLEE0ZMEK005

T1701# TRANS POWER BCK-35DH LTT3PCMEK031

BIND HEAD+

GBJB3080

2015/06/08 13-5 A4D17_EL.fm

TYPE A

PARTS LIST [49PFL4909/F7 (Serial No.: DS2)]

Mechanical Parts

PRODUCT SAFETY NOTE: Products marked with a

# have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTE: Parts that are not assigned part numbers (---------) are not available.

Different parts from the original model 49PFL4909/F7 (Serial No. : DS1)

Ref. No. Description Part No.

LCD1# LCD PANEL ASSEMBLY U4D11P0 U4D11P0

2015/06/08 13-6 A4D1E_CA.fm

Electrical Parts

PRODUCT SAFETY NOTE: Products marked with a

# have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTES:

1. Parts that are not assigned part numbers (---------) are not available.

2. Tolerance of Capacitors and Resistors are noted with the following symbols.

C.....±0.25% D.....±0.5% F.....±1%

G.....±2% J......±5% K.....±10%

M.....±20% N.....±30% Z.....+80/-20%

Different parts from the original model 49PFL4909/F7 (Serial No. : DS1)

There is no difference from the original model 49PFL4909/F7 (Serial No.: DS1) for Electrical Parts section.

2015/06/08 13-7 A4D1E_EL.fm

TYPE A

PARTS LIST [49PFL4609/F7 (Serial No.: DS1)]

Mechanical Parts

PRODUCT SAFETY NOTE: Products marked with a

# have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTE: Parts that are not assigned part numbers (---------) are not available.

Different parts from the original model 49PFL4909/F7 (Serial No. : DS1)

Ref. No. Description Part No.

A15# RATING LABEL A4D1BUH ----------

A17 ENERGY GUIDE LABEL A4D1FUH ----------

SBA1 50W STAND BASE ASSEMBLY (FC) A21U0UD 1EMN29162A

SNA1 50W STAND HINGE ASSEMBLY (FC)

S1 CARTON A4D1BUH 2EMC00355

X6 QUICK START GUIDE A4D1BUH 2EMN00155B

A4GU5UH

2EMN00139A

2015/06/08 13-8 A4D1B_CA.fm

Electrical Parts

PRODUCT SAFETY NOTE: Products marked with a

#have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTES:

1. Parts that are not assigned part numbers (---------) are not available.

2. Tolerance of Capacitors and Resistors are noted with the following symbols.

C.....±0.25% D.....±0.5% F.....±1%

G.....±2% J......±5% K.....±10%

M.....±20% N.....±30% Z.....+80/-20%

Different parts from the original model 49PFL4909/F7 (Serial No. : DS1)

Ref. No. Description Part No.

DIGITAL MAIN CBA UNIT A4D1BMMA-006

2015/06/08 13-9 A4D1B_EL.fm

TYPE A

PARTS LIST [49PFL4609/F7 (Serial No.: DS2)]

Mechanical Parts

PRODUCT SAFETY NOTE: Products marked with a

#have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTE: Parts that are not assigned part numbers (---------) are not available.

Different parts from the original model 49PFL4909/F7 (Serial No. : DS1)

Ref. No. Description Part No.

A15# RATING LABEL A4D1BUH ----------

A17 ENERGY GUIDE LABEL A4D1FUH ----------

SBA1 50W STAND BASE ASSEMBLY (FC) A21U0UD 1EMN29162A

SNA1 50W STAND HINGE ASSEMBLY (FC)

S1 CARTON A4D1BUH 2EMC00355

X6 QUICK START GUIDE A4D1BUH 2EMN00155B

LCD1# LCD PANEL ASSY U4D11P0 U4D11P0

A4GU5UH

2EMN00139A

2015/06/08 13-10 A4D1F_CA.fm

Electrical Parts

PRODUCT SAFETY NOTE: Products marked with a

#have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTES:

1. Parts that are not assigned part numbers (---------) are not available.

2. Tolerance of Capacitors and Resistors are noted with the following symbols.

C.....±0.25% D.....±0.5% F.....±1%

G.....±2% J......±5% K.....±10%

M.....±20% N.....±30% Z.....+80/-20%

Different parts from the original model 49PFL4909/F7 (Serial No. : DS1)

Ref. No. Description Part No.

DIGITAL MAIN CBA UNIT A4D1BMMA-006

2015/06/08 13-11 A4D1F_EL.fm

TYPE A

PARTS LIST [49PFL4909/F8 (Serial No.: XA1)]

Mechanical Parts

PRODUCT SAFETY NOTE: Products marked with a

# have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTE: Parts that are not assigned part numbers (---------) are not available.

Different parts from the original model 49PFL4909/F7 (Serial No. : DS1)

Ref. No. Description Part No.

A15# RATING LABEL A4D1CMA ----------

A16 LOGO LABEL A4DFBMA ----------

A17 Not used

S1 CARTON A4D1CMA 2EMC00383

S12 CARTON LABEL A4D1CMA ----------

X2# OWNERS MANUAL A4D1CMA 2EMN00174C

X6 QUICK START GUIDE A4D1CMA 2EMN00175A

X14 ADDENDUM SHEET A4D1CMA 2EMN00341

2015/06/08 13-12 A4D1C_CA.fm

Electrical Parts

PRODUCT SAFETY NOTE: Products marked with a

# have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTES:

1. Parts that are not assigned part numbers (---------) are not available.

2. Tolerance of Capacitors and Resistors are noted with the following symbols.

C.....±0.25% D.....±0.5% F.....±1%

G.....±2% J......±5% K.....±10%

M.....±20% N.....±30% Z.....+80/-20%

Different parts from the original model 49PFL4909/F7 (Serial No. : DS1)

Ref. No. Description Part No.

DIGITAL MAIN CBA UNIT A4D1CMMA-006

2015/06/08 13-13 A4D1C_EL.fm

TYPE A

PARTS LIST [49PFL4909/F8 (Serial No.: XA2)]

Mechanical Parts

PRODUCT SAFETY NOTE: Products marked with a

#have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTE: Parts that are not assigned part numbers (---------) are not available.

Different parts from the original model 49PFL4909/F7 (Serial No. : DS1)

Ref. No. Description Part No.

A15# RATING LABEL A4D1CMA ----------

A16 LOGO LABEL A4DFBMA ----------

A17 Not used

S1 CARTON A4D1CMA 2EMC00383

S12 CARTON LABEL A4D1CMA ----------

X2# OWNERS MANUAL A4D1CMA 2EMN00174C

X6 QUICK START GUIDE A4D1CMA 2EMN00175A

X14 ADDENDUM SHEET A4D1CMA 2EMN00341

LCD1# LCD PANEL ASSEMBLY U4D11P0

2015/06/08 13-14 A4D1D_CA.fm

Electrical Parts

PRODUCT SAFETY NOTE: Products marked with a

# have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTES:

1. Parts that are not assigned part numbers (---------) are not available.

2. Tolerance of Capacitors and Resistors are noted with the following symbols.

C.....±0.25% D.....±0.5% F.....±1%

G.....±2% J......±5% K.....±10%

M.....±20% N.....±30% Z.....+80/-20%

Different parts from the original model 49PFL4909/F7 (Serial No. : DS1)

Ref. No. Description Part No.

DIGITAL MAIN CBA UNIT A4D1CMMA-006

2015/06/08 13-15 A4D1D_EL.fm

TYPE A

PARTS LIST [49PFL4909/F8 (Serial No.: XA3)]

Mechanical Parts

PRODUCT SAFETY NOTE: Products marked with a

#have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTE: Parts that are not assigned part numbers (---------) are not available.

Different parts from the original model 49PFL4909/F7 (Serial No. : DS1)

Ref. No. Description Part No.

A15# RATING LABEL A4D1CMA ----------

A16 LOGO LABEL A4DFBMA ----------

A17 Not used

S1 CARTON A4D1CMA 2EMC00764

S12 CARTON LABEL A4D1CMA ----------

X2# OWNERS MANUAL A4D1CMA 2EMN00174C

X6 QUICK START GUIDE A4D1CMA 2EMN00175A

X14 ADDENDUM SHEET A4D1CMA 2EMN00341

LCD1# LCD PANEL ASSEMBLY U4D10P0

2015/09/01 13-16 A4D1G_CA.fm

Electrical Parts

PRODUCT SAFETY NOTE: Products marked with a

# have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTES:

1. Parts that are not assigned part numbers (---------) are not available.

2. Tolerance of Capacitors and Resistors are noted with the following symbols.

C.....±0.25% D.....±0.5% F.....±1%

G.....±2% J......±5% K.....±10%

M.....±20% N.....±30% Z.....+80/-20%

Different parts from the original model 49PFL4909/F7 (Serial No. : DS1)

Ref. No. Description Part No.

DIGITAL MAIN CBA UNIT A4D1GMMA-001

2015/09/01 13-17 A4D1G_EL.fm

TYPE B

PARTS LIST [49PFL4709/F8 (Serial No.: XA1)]

Mechanical Parts

PRODUCT SAFETY NOTE: Products marked with a

# have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTE: Parts that are not assigned part numbers (---------) are not available.

Different parts from the original model 49PFL4909/F7 (Serial No. : DS1)

Ref. No. Description Part No.

A3-1 REAR CABINET L A4G1AMA 2EMM00332B

A13 JACK HOLDER A31M0UT 1EM334000

A15# RATING LABEL A4G1AMA ----------

A16 LOGO LABEL A4AFHMA ----------

A17 Not used

CL501 FFC WIRE ASSEMBLY 23PIN 23PIN/WHITE/

CL3013 FFC WIRE ASSEMBLY 51PIN(W/SHIELD) 51P/

S1 CARTON A4G1AMA 2EMC00384

S12 CARTON LABEL A4G1AMA ----------

X2# OWNERS MANUAL A4G1AMA 2EMN00172

X3 REMOTE CONTROL UNIT YKF335-005 URMT41JHG005

X6 QUICK START GUIDE A4G1AMA 2EMN00173

406MM

FFC/SHIELD/491MM

WX1A4GU5S201

WX1A4G1AT401

2015/06/08 13-18 A4G1A_CA.fm

Electrical Parts

PRODUCT SAFETY NOTE: Products marked with a

# have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTES:

1. Parts that are not assigned part numbers (---------) are not available.

2. Tolerance of Capacitors and Resistors are noted with the following symbols.

C.....±0.25% D.....±0.5% F.....±1%

G.....±2% J......±5% K.....±10%

M.....±20% N.....±30% Z.....+80/-20%

Different parts from the original model 49PFL4909/F7 (Serial No. : DS1)

Ref. No. Description Part No.

DIGITAL MAIN CBA UNIT A4G1AMMA-005

CN3701 Not used

IC3006 IC 32M-BIT SERIAL FLASH MEMORY

IC3009 IC RESET IC-PST8429UR QSCA0T0MM075

IC3019 IC USB HIGH-SIDE SW AP2151WG-7/SOT25/

IC3101 IC MSD8220LB1-S1 MSD8220LB1-S1 EPLQFP NSAA0RMST002

IC3102 Not used

IC3103 Not used

IC3201 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021

IC3601 IC REGULATOR BD00IA5WEFJ-E2 QSCA0T0RM233

IC3602 REGULATOR AP1117EG-13 NSCA0TDES012

IC3603 IC REGULATOR BD00IA5WEFJ-E2 QSCA0T0RM233

IC3604 IC DC-DC CONVERTER MP2314GJ-Z TSOT23-8NSCA0T09M025

W25Q32FVSSIG

5PI

NSCA0R0ZM018

NSCA0TDES015

Ref. No. Description Part No.

Q703 Not used

Q705 Not used

R667 RES CHIP 1608 1/10W J 15k W RRXA153HH013

R748 Not used

R749 Not used

R750 Not used

R751 Not used

R753 Not used

R754 Not used

R755 Not used

R756 Not used

IC3605 IC DC-DC CONVERTER MP2314GJ-Z TSOT23-8NSCA0T09M025

IC3607 Not used

IC3701 Not used

IC3801 IC D-CLASS AUDIO POWER AMPLIFI

IC3803 Not used

IC3851 IC STEREO HEADPHONE AMPLIFIER

IC3901 Not used

TU3001 Not used

TU3901 TUNER UNIT U9004UH U9004UH

IC3401 Not used

IC3402 Not used

C652 Not used

C657 CAP ELE 470µF/16V/M/85 CEC4710V8006

C728 Not used

C729 Not used

D715 Not used

D716 Not used

TPA3110D2PWPR

TS488IQT DFN8 8PIN

POWER SUPPLY CBA A4GU5MPW-001

NSCA0T0TY073

NSCA0T0SS070

2015/06/08 13-19 A4G1A_EL.fm

REVISION HISTORY

Chassis PL14.22

• 2014/02/20 49PFL4909/F7 (Serial No.: DS1) added

• 2014/02/20 49PFL4609/F7 (Serial No.: DS1) added

• 2014/04/30 49PFL4709/F8 (Serial No.: XA1) added

• 2014/05/26 49PFL4909/F8 (Serial No.: XA1) added

• 2014/10/13 49PFL4609/F7 (Serial No.: DS2) added

• 2014/10/13 49PFL4909/F7 (Serial No.: DS2) added

• 2014/11/11 49PFL4909/F8 (Serial No.: XA2) added

• 2015/07/01 49PFL4909/F8 (Serial No.: XA3) First draft added

14-1 PL14.22REV

COMPARISON LIST OF MODEL NAMES

Chassis PL14.22

49PFL4909/F7 (DS1) A4D17UH TYPE A

(DS2) A4D1EUH TYPE A

49PFL4609/F7 (DS1) A4D1BUH TYPE A

(DS2) A4D1FUH TYPE A

49PFL4709/F8 (XA1) A4G1AMA TYPE B

49PFL4909/F8 (XA1) A4D1CMA TYPE A

(XA2) A4D1DMA TYPE A (XA3) A4D1GMA TYPE A

PL14.22COM

Philips 49PL4909/F8 Schematic

Specifications and Main Features

Frequently Asked Questions

User Manual

SPECIFICATIONS

IMPORTANT SAFETY PRECAUTIONS

STANDARD NOTES FOR SERVICING

CABINET DISASSEMBLY INSTRUCTIONS

ELECTRICAL ADJUSTMENT INSTRUCTIONS

[TYPE A]

[TYPE B]

HOW TO INITIALIZE THE LCD TV

[TYPE A]

FIRMWARE RENEWAL MODE

[TYPE B]

TROUBLESHOOTING

BLOCK DIAGRAMS

[TYPE A]

[TYPE B]

SCHEMATIC DIAGRAMS / CBA AND TEST POINTS

[TYPE A]

WIRING DIAGRAMS

[TYPE B]

EXPLODED VIEWS

TYPE A

TYPE B

REVISION HISTORY