Viewing Angle - H (L+R)
Viewing Angle - V
Response Time (ms)
Analog + PWM dimming
2D/3D Logic (2D/3D Active/3D Passive )
High end (7601-31A062-0144FLP3
7601-32E232-0244FLP1
PMR 100 HZ
Min:220cd/m2 ,Typ:260cd/m2
176°
176°
8ms
YES
2D
1
Page 3
Color GamutNTSC 66%
PQ engineDigital Crystal Clear
PQ Resolution N/A
Directional Super Resolution (on 2D &
3D)
N/A
Improved 3D Super ResolutionN/A
ISF Color ManagementN/A
Digital Natural Motion (2D/3D )
Perfect Natural Motion (2D/3D )
N/A
N/A
2D to 3D ConversionN/A
3D Depth adjustment (Auto/Offset)N/A
Auto 3D DetectionN/A
Micro Dimming DemoN/A
Micro Dimming mode N/A
Dual View (2 Player Full Screen
Brightness (Shop Vivid mode: 10%
Pixel Plus Link (I/II/III)
Active Control
Local Contrast
"UHD Display" - logo (Industry)
"UHD Receiver" - logo (Industry) -
pending std
HDMI 2.0 4:4:4 @ 60p
10-bit color support
DAPQ
Ambilight
480i, 480p,576i,
576p,720p,1080i,1080p
(24/25/30/50/60Hz)
YES(1% boost)
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
2
Page 4
Ambilight VersionN/A
PixelsN/A
Ambilight Performance (nit, no of colors,
halo length)
N/A
Ambilight Features (Wall colour
adaptive, Lounge Light Mode, Ambilight
N/A
Motion, Gaming Mode )
Ambilight for 3DN/A
Ambilight for all TV EventsN/A
Ambilight Open Source via
JointSpaceApp
N/A
Wall Distance Adaptive (Stand vs Mount)N/A
Motion AdaptiveN/A
Built-in AL + HueN/A
TV as Lamp(s) in Hue ecosystemN/A
In screen demo in mobile shop appN/A
Ambi Wakeup (ref HTV)N/A
AmbimusicN/A
Sound (TV)
Sound (Internal)
Output Power (10% THD) RMS16W
Speaker configuration 8W+8W
Speaker system2.0
Speaker type
Auto Volume Levelier / Auto Volume
Ux (Basic: without Dashboard,
Advanced: with Dashboard)
Basic
Animations N/A
Drag and drop N/A
Remote Control Version (state if include
Keyboard/Pointer)
Sensor.accelerometer & sensor
gyroscope
N/A
N/A
Easy access to eDFU (Blue key) N/A
Text Entry (Basic : Text Entry via HID
and/or On-screen Keyboard)
Basic
Multi-view N/A
Multi-task N/A
Screen Format Adjustments
4:3,16:9
Dual Screen (TV and TeleText) N/A
TeletextYES
e-StickerN/A
Priority Channel ListN/A
Channel Cloning via USBN/A
Logo Editor (Channel Editor)N/A
5
Page 7
Channel Matrix with EPG dataN/A
Channel Scanning (Australia/NZ)N/A
Time Zone (Australia/NZ)N/A
PC SortingN/A
Intelligent Source ListN/A
On-screen Remote (via HDMI)N/A
Cold boot to broadcastN/A
Cold boot to online dashboardN/A
Warm boot to broadcastN/A
Warm boot to online dashboardN/A
Zapping OSD with EPG dataN/A
Electronic Program Guide (IP &
Broadcast)
N/A
8 Days Electronic Program GuideYES
Live Setting Assistant (include PQ level) N/A
Signal Strength Indication YES
Pause TV/USB recording (PVR) YES
Two simultaneous recordings in stdby N/A
UI Languages
English, Malaysia, Indonesian, Thai,
Vietnamese,Chinese
Memory Profile (DRAM) 128M
Menu Layout Update N/A
Wizards (Ease of Installation) N/A
Single Sign On (google a/c only) N/A
Personalized DashboardN/A
Face recognition N/A
Shopmode 2015 N/A
CloudTV app content in search and
Dashboard (on TV)
N/A
Firmware Upgradeable YES
Multimedia Applications
Video Playback Formats MPEG-2/MPEG-4 /H.264
Subtitles Formats SupportSRT、ASS
Music Playback Formats
MPEG-1,MPEG-2(Layer I/II),MP3,
AAC-LC, HE-AAC
Picture Playback FormatsJPEG、BMP、PNG
Smart TVN/A
Software Platform
6
N/A
Page 8
Android Home Page
d
Android OS
UI Resolution
Google Voice Search
Google Hangouts
Remote Control
Gesture
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Pre-installed Google Apps (Google
Search, Google Hangouts, Google Play
N/A
Movies, Google Play Music, Youtube)
Basic Performance Profile
Google Play
N/A
N/A
Memory size to install appsN/A
Extendable USB storage for App
API - access controlN/A
xTV Support
Rich User Interaction
N/A
N/A
Smart HomeN/A
4k photo support in Android appsN/A
4k photo support in Picture appsN/A
4k photo support in USB/DLNAN/A
UHD content playback from all sources
(USB,DLNA,web)
NextFlix UHD
Youtube UHD
N/A
N/A
N/A
Google Play UHDN/A
Smart TV with Broadcast PIP; single
video
N/A
SMART TV offline content (cached)N/A
MPEG-DASH (CENC & CFF)N/A
HLS
N/A
Wake up from APPN/A
Preinstalled Apps
N/A
7
Page 9
Netflix *
YouTube Leanback (HTML5) *
Spotify *
BBC iPlayer *
Skype
Skype Cowatch (mix audio)
Cloud Explorer
Cloud TV
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Smart TV ServicesN/A
Social AppsN/A
Game Dashboard in Google launcher
OpenGL Games
Playstation Now App
OnLive App
STA 3.0 & 4.0 Clients
STA shared App store
Camera & Mic API
TV as an app (Verimatrix, etc)
Companion Apps
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Philips TV Remote AppN/A
Sharing in Remote App
Ambilight TV App
Ambilight+Hue App
User Manual App
Channel Editor - PC Client App
N/A
N/A
N/A
N/A
N/A
Mobile app for in-shop (cover
MRA/Demo Me/Shop RC functions)
N/A
Proximity based shop app activation
(BTLE/NFC/QR tbc)
MyRemote App (Old TV Remote App)
Ambilight Lounge App
N/A
N/A
N/A
Broadcast/Certification
DVB-T/CN/A
DVB-S/S2N/A
DVB-T/T2YES
DVB-C2N/A
SBTVD-T (Brazil)N/A
SATVD-T (Argentina)N/A
Analog (LATAM/APMEA)
PAL SECAM NTSC
Nicam (APMEA)N/A
8
Page 10
Enhanced SSUN/A
Italy HD Book 2.1.1 (GOLD)N/A
HD-Book Italy 3.0 (HEVC@FHD)N/A
UK D Book 7aN/A
Freeview SD (UK)N/A
Freeview HD (UK)N/A
MHEG 5(只有HbbTV有)N/A
TiVuON (IT)N/A
TNT HD (FR)N/A
Argentina Ginga - NCLN/A
Brazil Ginga (A/B )N/A
Video PlaybackN/A
Dual Cam (CI+)N/A
Dual TunerN/A
CI+ 1.4 Multistream CAM N/A
CI+ 1.3 CAM N/A
HBBTV 1.5N/A
HBBTV 2.0N/A
MHPN/A
Ziggo InteractiefN/A
3D DVB Phase 1N/A
3D signaling bits in broadcastN/A
Background update installationN/A
Marlin/ Play readyN/A
Sustainability/Power
PVC / BFR Free N/A
Mercury Free N/A
Cabinet Resin ABS
Eco-Flower Certified N/A
ECO Mode N/A
Mains Power AC 100-240V 50/60Hz
Standby Power<0.5W
Quick Startup NA
Network Standby mode (max 6W) NA
Off Mode Power <0.5W
Auto Switch-Off Timer YES
Green packaging (Non-EPS) YES
Light Sensor NA
Picture Mute (For Radio) N/A
9
Page 11
EU Energy Label (A++/A+/A/B ) -
Requirement
NA
non-EU Energy Label - Standby Label
(A/B/C)
NA
Blauer Engel (Germany)NA
Accessory
By-packed accessories
Active Glasses (509)N/A
Active Glasses (529)N/A
Passive Glasses (PTA417 )N/A
Dual Gaming GlassesN/A
Woofer (e.g. SWB50) with SoundbeamN/A
Sound Bar N/A
Detachable speaker base N/A
Wireless audio adaptor N/A
Wi-Fi Adapter (PTA01/00/PTA127/55 )N/A
Skype Camera (PTA317 )N/A
Table Stand
Unit with stand
Unit without stand
Carton
Wall-mount
Weight
Product without Stand
Product with Stand
Product in Packaging
968×614×219mm
968×565×77mm
1085×667×150mm
200*300 mm
7.8kg
8 kg
10 kg
11
Page 13
43PFT5250/56
12
Page 14
13
Page 15
14
Page 16
15
Page 17
16
Page 18
17
Page 19
18
Page 20
Factory menu entry: Press MENU, and then press 1999
Primary menu Secondary menu Value,remark
MDOE VGA,YPBPR,Selection
R-GAIN
G-GAIN
ADC ADJUST
PICTURE MODE
W/B ADJUST
SSC SETTING
Spectial set 2HOUR OFF 2hours power off enable
VIF Vif 1 Vif set
B-GAIN
R-OFFSET
G-OFFSET
B-OFFSET
AUTO ADC ADC automatically adjust
Input Source Source Selection
MODE Dynamic/Standard/Sotf/User
BRIGHTNESS BRIGHTNESS
CONTRAST CONTRAST
COLOR COLOR
SHARPNESS SHARPNESS
TINT TINT
Copy all No function
inputsource Source Selection
TEMPERATURE Cool, Standard, Wa rm
R-GAIN
G-GAIN
B-GAIN
R-OFFSET
G-OFFSET
B-OFFSET
Copy all No function
MIU Enable DDR spectrum enable
MIU0 Span Exhibition frequently wide
MIU Step Spread spectrum step
LVDS enable LVDS spectrum enable
LVDS Span Exhibition frequently wide
LVDS Step Spread spectrum step
LVDS swing LVDS swing
WDT Watch dog on/o ff
White pattern White pattern sel ect ion
Restore user default Factory reset
PVR_RECORDALL PVR Record on/off
Power Power mode selection
Mirror Mirror function selection
Ageing mode Ageing mode enable
Overscan_vposition Adjust overscal V position
other Test pattern
UART DEBUG DEBUG ON/OFF
HDMI CEC/ARC CEC/ARC ON/OFF
Backlight Adjust backlight
CI+ key usb upgrade CI+ key usb upgrade
SW information SW information
MODE Feature Selection
OSD 0
Non-linear
Channel table1 KTC factory Frequecy table set
CI factory setting No function
Channel table2 KTC factory Frequecy table set
Channel dvbt KTC factory Frequecy table set
3. Protection or without light (refers to the disappearance of image several seconds
after the emergence of image)
4. White panel
Theimagedisappearedimmediatelyafterthe
emergence; check the plug of high-voltage switch board
for striking sparks and poor contact
No problems identified, replace high-voltage
board; if the fault remains, check the contact
line of back light of LCD for any damage, and
replace LCD board.
Ifthereis sparkstriking,
replace high-voltage board
YES
NO
White panel refers to the back light works
without visible signal and just show white
screen. Check the voltage of socket for flat
cable connecting the main board to screen
for abnormality
Check the interface between main board
and connect line for any looseness,
shedding,ifnoabnormityexisted,
replace LCD screen
Check the power supply chip of
control screen or replace main
board
YES
NO
22
Page 24
5. White screen after power-off (work normally when power on, but when power-off or
no signal input, the screen shows a white screen)
6. TV without channel or with color cast
Check whether there is change of voltage at the high voltage
board controlled by main board when power-on and power-off
Check whether the voltage change of the control pins on
the plug interface of high voltage board is normal when
power-on and power-off
Check whether the voltage of the pin on main chip
controlling the working voltage of high voltage board is
normal when power-on and power-off
YES
NO
Thecircuit
relatedto
highvoltage
board is poor
Checkwhetherthelines
between main board and high
voltage board is in open-loop
or poor contact
Check relevant circuits of
highvoltageboard
controlled by main board
Replace poor main
chipsorrecopy
software
Check TV antenna plug for looseness and
poor contact
If with color cast, check the setting of
color system under menu; and change
of color system to see whether it is
normal (Usually set to automatic)
Replace antenna plug
Check the antenna and itssignal
source, if no problems exist, replace
tuner or control chips with the same
model
NO
YES
YES
YES
NO
NO
23
Page 25
7. Poor sound
8.No VGA input signal
Switch to other audio input, check whether DVD
input and PC main board input has sound
Poor sound refers to without sound or with noise; check
whether the selection of sound system is proper
No sound; check whether remote control mute is
selected and switch sound system
No sound for other inputs; check the sound
amplifier and the shared control circuit
There is sound for other inputs,
replace TV tuner or control chip
YES
YES
NO
NO
VGA signal input does not respond, the screen
prompts “Please input signal”, check whether PC
signal source and signal line is normal.
Check VGA signal input board and see whether the row
and field sync signal protection diode is broke down
Replace PC or signal line, check
display VGA plug for looseness
Replace the motherboard or
factory reset is normal
Replace the 5.6V Zener diode
on the motherboard
NO
YES
YES
NO
24
Page 26
9. Poor embedded power supply of TV
10. Common fault of LCD screen
10.1 Bright line or bright belt (BL): constant longitudinal or transverse illuminating line or
belt due to non-conformed connection between IC and glass
10.2 Dark line (DL):constant longitudinal or transverse illuminating line dueto
non-conformed connection between IC and glass.
10.3 White panel (WP): only light tube illuminates owing to non-conformed drive plate of
the LCD, without any display signal in the display area, and the whole screen is white.
10.4 Screen breaking: (overflow of LCD): with damage or invisible damage of the liquid
crystal glass, irregular black defect occurs from liquid crystal body to glass and polarizer,
which can not be seen at any image. The overflow portion can not form image and does not
display.
10.5 Pressing Scrape (PS): after local display area at the front of LCD is heavily pressed,
Power on, check embedded power supply 5VSB in TV for 5V voltage output
High electrical level existed at
STB (higher than 2.5V)
Replace power supply
YES
YES
NO
NO
Check EC2 for 380-400V
voltage; if there is not,
replace power supply
Check +5V , +12V
for normal input
YES
Check power supply line for looseness, check indictor for
working and power supply socket for looseness
NO
NO
Replace power
supply
Fastenlines
and socket
25
Page 27
glass of the pressed portion is not damaged, the liquid crystal body can not display normally,
with spot or block black defect.
10.6 Screen mess: irregular color display arising from damage of driving plate in LCD.
26
Page 28
MSD6308 Program Software Burning Instruction
VGA
1. Connect burning board and computer; connect burning board and waiting burning main board VGA
socket with VGA connecting wire.
ISP burning
board
To PC USB
interface
To main board
interface
2. Running, if the hint is driver
should be installed for burning board.
3. Click Help in the toolbar, when pop up Present, click the first item.
将烧录板端与电脑接口排序
Sorting set burning board
设置,确保两个一致
terminal and PC interface
make sure they are the same.
I2C address set as the following red frame 0XB2
27
·
Page 29
4. Sorting set the burning board terminal and computer interface make sure the two are all set as automatic
connecting. (same as above).
28
Page 30
5.
Burning board terminal and
烧录板的端口排序必须为
has to be the same as
电脑里的排序一致
6. Click view in toolbar in the main menu, click the second( count backwards) view in main toolbar and the
second(count backwards) “ Eagle NAND Program” to get into the next menu.
29
Page 31
Follow these instructions to load the appropriate file
Make sure loading right,
click here to start burning.
Load suffix
file .txt
Load 050B-Tool.bin file
Load RomBoot.bin file
When toolbar shows:Success .Please reset power. That means burning finished (Notice:Although the hint shows
30
Page 32
complete but it may not be burning completed, wait for 5 minutes to shut off power. If U disk cannot be used
for burning, boot file should be burning again until U disk can be used for upgrading. ).
After prompting success, then
click POWER on button panel to
check whether main board can
be starting on, if it can be started
on means burning success,
otherwise as unsuccessful
2, Main board software upgrades.
1,U disk plugged into main board , put MstarUpgrade.bin software into formatted U disk , press and hold
on VOL + key button on TV key board, after about three seconds , LED starts flashing , wait until LED
lights no longer flashing and steady mean burning success. If press three seconds, LED lights (no flashing
into place) then boot files should be burned.
2, after prompting success, then click POWER on button panel to check whether main board can be
starting on, if it can be started on means burning success, otherwise as unsuccessful.
3, CI+KEY burning
i.CI + is certain TV operators encrypted to digital TV channels, need to watch the event on TV after decrypting,
if TV software upgraded , must re- burn ci + key, otherwise the
ii.client will not normally watch encrypted program .
iii.All parts on main board with CI socket must burn ci + key, if any question, please contact the engineer .
iv.ci + key running reference to "MSD6308 program ci + key count file modification ", "MSD6308 ci + key burn".