Philips 42HFL7580A/27, 42HFL5860D/27, 37HFL5560D/27, 26HFL5830D/27 Quick Start Guide

If an “F” appears in the upper right hand corner of the screen, it indicates the TV is in factory mode. To restore normal operation, press and hold the CHANNEL DOWN and the VOLUME DOWN keyboard buttons on the side of the TV for a few seconds. The “F” should disappear.

If the TV still does not communicate with the internal interactive card, select FEATURES in the CONFIGURA-

TION menu and press Æ to enter the FEATURES menu.

Press

and select LOW POWER

STANDBY.

Press Æ and select NO.

POWER

SLEE P

GUID E

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

809

5 6

To power outlet

AC in

To wall socket

Change the settings of the channels as desired (delete unwanted channels, assign digital channels, assign input sources). Refer to “Changing the settings of a channel” section in this guide.

Change the TV settings as desired. Refer to “Conguring Volume / Picture and Other Common settings” section in this guide. For detailed explanation, refer to the user manual.

Record the TV conguration settings into a USB device. Refer to the “Cloning the TV conguration” section in this guide.

Slide the button to the Setup position.

Power on the TV.

Connect the RF signal and plug the TV into a power outlet.

Press M on the remote to display the Setup menu. Press ï repeatedly until AUTO INSTALL TV is highlighted.

Press Æ to start automatic channel installation.

How to use this guide What you can nd in the box

Stand alone installation

Quick Start Guide

Changing the settings of a channel

Conguring the Volume / Picture and Other Common settings

Note: This section is only applicable after channels have been installed in the TV (see Section 3 on channel installation).

Press the M button on the remote to display the Setup menu. Press ï repeatedly until CHANNEL INSTALL is highlighted.

Cloning the TV conguration to a USB Device and the USB Device conguration to the TV

Installing a Pay-Per-View SmartCard

Installing a Pay-Per-View Box

M6 (18mm) x 4

M5 (25mm) x 2

x 2

Quick Start Guide

x 4

Quick Start Guide

37” / 42” / 52” models

Set the SOURCE option to USB. To clone the TV conguration to the USB device, set the DIREC- TION option to UPLOAD.

Press Æ to enter into the CHANNEL INSTALL menu and press 0 - 9 to select a channel.

Document order number: 3139 285 20011

Press ï to select INPUT and press Í or Æ to select the input source.

Press ï repeatedly until DIGITAL is highlighted. Press Æ to select YES. Set the RF CHANNEL NUMBER to the physical channel where the digital program is located and the MPEG PROGRAM NUMBER to the program desired within that physical channel.

Note : You can also highlight the DIGITAL CH SCROLL item and press Í or Æ to select the digital channel numbers.

Press ï to select RINGS and press Æ repeatedly to select RING 1 to 4. Press Î or ï to save or remove the channel from each ring. The ‘X’ means the channel is saved.

Press M on the remote to display the SETUP menu and press ï repeatedly until CONFIGURATION is selected.

Press Æ to enter into the CONFIGURA- TION menu and press Æ again to enter the SWITCH ON / OSD menu.

Press ï to select SWITCH ON CHANNEL. Press Æ to select the channel that you want to appear when the TV is powered on. Do likewise for SWITCH ON

VOLUME, SWITCH ON PIC FMT and WELCOME MESSAGE.

In the CONFIGURATION menu, select PICTURE / SOUND. Press Í or Æ to enter the PICTURE / SOUND menu and change to your desired picture and sound settings.

In the CONFIGURATION menu, select

CONTROL. Press Í or Æ to enter the CONTROL menu and select MAX VOLUME to set your desired maximum

volume setting.

In the CONFIGURATION menu, select VIDEO ADJUSTMENT and press Æ to enter the VIDEO

ADJUSTMENT menu. Select HORIZONTAL or VERTICAL and use

Í or Æ to adjust picture horizontally or vertically.

Note : Ensure that the TV is turned o.

Insert the Pay-Per-View SmartCard into the SmartCard slot on the rear of the TV (available for certain models only) and connect the other cables as directed by the Pay-Per-View provider. After SmartCard has been inserted and the cables connected, turn on the TV.

26” / 32” models

To power outlet

POWER

SLEE P

GUID E

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

809

5 6

POWER

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

A/CH

809

5 6

POWER

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

A/CH

809

5 6

POWER

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

A/CH

809

5 6

POWER

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

A/CH

809

5 6

POWER

SLEE P

GUID E

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

A/CH

809

5 6

POWER

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

A/CH

809

5 6

POWER

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

A/CH

809

5 6

POWER

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

A/CH

809

5 6

Note : Step B in this section may not be needed as the Communication mode by default is set to SP - SPI. Perform this step only if you want to conrm the Communication mode is set correctly.

In the SETUP menu, select COMMUNICATION. Press Æ to enter the COMMUNICATION menu. Press Æ to select SP - SPI. Press ï and select STORE and press Æ button to store selection.

Press RECALL on the remote and check SP

- SPI is ONLINE. If SP - SPI shows “OFFLINE”, check that the RJ12 cable and connection between terminal and TV. is properly connected.

Connect to the Data 1 (RJ 12) connector at the rear of the TV.

Sample of Pay-Per-View box

NOTE : Perform this step only if you are installing digital channels.

Diagnosing Basic Problems

If the TV does not seem to communicate with the external interactive terminal, perform the following steps:

Press RECALL on the remote (in Setup position). Item 08 of the menu should read COM- MUNICATION SP - SPI ONLINE.

POWER

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

809

5 6

01 26HF7945D / 27 02 SV1A0707100003 03 IC7U1 - 0 .11 / M3 .22 04 LC72HUL1 - 0 .13 05 OPT (30) 22 20 1C 23 06 OPT - MODEL 26HF7945D / 27 07 08 COMMUNICATION SP - SPI ONLINE 09 TV 2 NOT TUNED

If it is not SP -SPI, press the M button on the remote to display the Setup menu. Press ï to select COMMUNICA-

TION and press Æ repeatedly to select SP - SPI.

Press Æ to select STORE and press Æ to store selection.

If the TV still does not communicate with the external interactive terminal, press RECALL on the remote. Check item 08 of the menu.

For Pay-Per-View Box, if it reads “COMMUNICATION SP -SPI OFFLINE”, check that the RJ12 cable and connection between terminal and TV is properly connected.

For the Pay-Per-View SmartCard, check the SmartCard is correctly inserted into the card slot of the TV.

POWER

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

809

5 6

01 26HF7945D / 27 02 SV1A0707100003 03 IC7U1 - 0 .11 / M3 .22 04 LC72HUL1 - 0 .13 05 OPT (30) 22 20 1C 23 06 OPT - MODEL 26HF7945D / 27 07 08 COMMUNICATION SP - SPI OFFLINE 09 TV 2 NOT TUNED

Press RECALL on the remote and check SP - SPI is ONLINE. If SP - SPI shows “OFFLINE”, check the Pay-Per-View SmartCard is correctly inserted into the card slot of the TV.

COMMUNICATION

COMMUNICATION SP - SPI

STORE > DCM TYPE >

Note : Step B in this section may not be needed as the COMMUNICATION mode

by default is set to SP - SPI. Perform this step only if you want to conrm the COM- MUNICATION mode is set correctly.

In the SETUP menu, select COMMUNICATION. Press

Æ to enter the COMMUNICATION menu. Press Æ to select SP - SPI. Press ï to select STORE and

press Æ to store your selection.

COMMUNICATION

COMMUNICATION SP - SPI

STORE > DCM TYPE >

In the CONFIGURATION menu, select

FEATURES and press Æ to enter the FEATURES menu.

Press ï and select LOW POWER STANDBY.

Press Æ and select NO.

Note: For the Pay-Per-View SmartCard to function, NO must be selected.

POWER

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

809

5 6

01 26HF7945D / 27 02 SV1A0707100003 03 IC7U1 - 0 .11 / M3 .22 04 LC72HUL1 - 0 .13 05 OPT (30) 22 20 1C 23 06 OPT - MODEL 26HF7945D / 27 07 08 COMMUNICATION SP - SPI OFFLINE 09 TV 2 NOT TUNED

POWER

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

809

5 6

01 26HF7945D / 27 02 SV1A0707100003 03 IC7U1 - 0 .11 / M3 .22 04 LC72HUL1 - 0 .13 05 OPT (30) 22 20 1C 23 06 OPT - MODEL 26HF7945D / 27 07 08 COMMUNICATION SP - SPI OFFLINE 09 TV 2 NOT TUNED

CHANNEL INSTALL

SWITCH ON / OSD

WELCOME MESSAGE >

SWITCH ON CHANNEL TV 2

SWITCH ON VOLUME 30 SWITCH ON PIC FMT WIDESCREEN POWER ON LAST STATUS VOLUME INDICATOR YES CHANNEL DISPLAY ALL

CHANNEL INSTALL

SETUP

LANGUAGE ENGLISH COMMUNICATION > CHANNEL INSTALL > AUTO INSTALL TV > CABLE TUNING NO USE CHANNEL TABLE NO CURRENT RING RING1 DIGITAL SETUP >

CONFIGURATION >

CHANNEL INSTALL

PICTURE / SOUND

BRIGHTNESS 45

COLOR 38 CONTRAST 70 SHARPNESS 50 TINT 36 ACTIVE CONTROL YES TREBLE 52 BASS 55 BALANCE 0 AVL ON

CHANNEL INSTALL

CONTROL

ESP DIGIT TIMEOUT

3.0 3 DIGIT ENTRY NO SOURCE MENU YES CHANNEL NO MIN VOLUME 10

MAX VOLUME 35

CHANNEL INSTALL

VIDEO ADJUSTMENT

HORIZONTAL < >

VERTICAL < >

CHANNEL INSTALL

SETUP

LANGUAGE ENGLISH COMMUNICATION >

CHANNEL INSTALL >

AUTO INSTALL TV > CABLE TUNING NO USE CHANNEL TABLE NO CURRENT RING RING1 DIGITAL SETUP

CONFIGURATION

POWER

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

A/CH

809

5 6

CHANNEL INSTALL

CHANNEL

INPUT

DIGITAL RINGS

(1 ) (2 ) (3 ) (4 )

LABEL ) > MUTE NONE

(

TUNER

TV 8

CHANNEL INSTALL

CHANNEL

INPUT TUNER DIGITAL NO RINGS (1 ) (2 ) (3 ) (4 ) LABEL

) >

MUTE NONE

CHANNEL INSTALL

TV 8

(

CHANNEL INPUT TUNER DIGITAL

RINGS (1X ) (2 ) (3 ) (4 )

LABEL ( ) > MUTE NONE

CHANNEL INSTALL

TV 8

SETUP

LANGUAGE ENGLISH COMMUNICATION > CHANNEL INSTALL >

AUTO INSTALL TV >

CABLE TUNING NO USE CHANNEL TABLE NO CURRENT RING RING1 DIGITAL SETUP > CONFIGURATION >

Note : Ensure that the TV is turned o.

Insert the RJ12 cable of the Pay-PerView box to the DATA 1 (RJ12) connector on the rear of the TV and connect the other cables as directed by the Pay-Per-View provider. After all the connection of cables are completed, turn on the TV.

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

A/CH

809

5 6

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

A/CH

809

5 6

SLEE P

GUID E

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

A/CH

809

5 6

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

A/CH

809

5 6

Set the SW TYPE option to CLONE DATA. Highlight START and press Æ to clone the USB device to the TV conguration.

The TV automatically restarts with the cloned software installed.

To clone the USB device to the another TV, insert the USB device in the USB Side slot. Proceed to SW DOWN- LOAD as instructed on the previous page.

Set the SOURCE option to USB. Set the DIRECTION option to DOWNLOAD.

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

A/CH

809

5 6

FEATURES

SMARTPOWER LOW SMART SOUND KEY SMART SOUND DEFAULT HDMI 1 AUDIO AV AUDIO

LOW POWER STANDBY NO

LOUD SPEAKER MUTE NO SW DOWNLOAD >

DEFAULT HDMI 2 AUDIO AV AUDIO

FEATURES

SMARTPOWER LOW SMART SOUND KEY SMART SOUND DEFAULT HDMI AUDIO AV AUDIO

LOW POWER STANDBY NO

LOUD SPEAKER MUTE NO RF DOWNLOAD >

C V I

PC AU DI O IN

H DM I 1

AV 1

H D M I 2

S E R V I C E

R S 2 3 2

S P D I F

DATA 1

S - V I D E O

VG A

AU D I O I N

To wall socket

Press the M button on the remote to display the Setup menu.

Enter CONFIGURATION uisng ï to scroll down. Press Æ to enter.

Enter FEATURES. Enter SW DOWNLOAD.

Prepare the USB stick by creating a folder called “SSB_NVM” in the root directory. Then create a folder within this folder called “ChannelTable”.

Insert the prepared USB Stick into the USB slot on the TV.

POWER

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

A/CH

809

5 6

SOURCE USB

DIRECTION

DOWNLOAD

SW TYPE

ALL

START

SW DOWNLOAD

SOURCE USB

DIRECTION

UPLOAD

SW TYPE

ALL

START

SW DOWNLOAD

POWER

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

A/CH

809

5 6

SOURCE USB

DIRECTION

DOWNLOAD

SW TYPE

ALL

START

SW DOWNLOAD

POWER

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

A/CH

809

5 6

Set the SW TYPE option as CLONE DATA. Highlight START and press Æ to clone the TV conguration to the USB device.

POWER

SLEE P

GUIDE

RESE T

SMAR T

GUES T

DCM

SETU P

TEXT

RECAL L

A/CH

809

5 6

CHANNEL INSTALL

CHANNEL TV 2 INPUT TUNER

DIGITAL CH SCROLL > RF CHANNEL NUMBER 8 MPEG PROGRAM NUMBER 2 RINGS (1 ) (2 ) (3 ) (4 ) LABEL ( ) > MUTE NONE

CHANNEL INSTALL

DIGITAL YES

Sample of Pay-Per-View SmartCard

The purpose of this Quick Start Guide is to assist you in getting this Philips Commercial television installed as quickly as possible. It contains the necessary information needed for most typical connections and installations. For detailed documentation of additional features, please consult the user manual or online help at www.philips.com/hospitality.

Go through this Quick Start Guide and read the instructions on : How to:

- perform a Stand alone installation

- change the settings of a channel

- congure the Volume / Picture and other common settings

- clone the TV conguration to a USB device and from the USB device to the TV

- install a Pay-Per-View SmartCard

- install a Pay-Per-View Box

- diagnose basic problems

The complete directions for use can be downloaded from the Philips Professional & Business Solutions website (www.philips.com/hospitality) by selecting the Hospitality Products link and then the model of the TV.