Service Manual
39” LCD TV
chassis PL13.11
Contents
TYPE A
39PFL2608/F7 PHILIPS (Serial No.: DS1, DS2)
39PFL2908/F7 PHILIPS (Serial No.: DS1)
39PFL4408/F8 PHILIPS (Serial No.: XA1)
TYPE B
39PFL2708/F7 PHILIPS (Serial No.: DS2)
TYPE C
39PFL2708/F7 PHILIPS (Serial No.: DS1)
39PFL4208/F8 PHILIPS (Serial No.: XA1)
This service manual contains information of different types of models.
Make sure to refer to the section describing your model.
This service manual contains information of different types of models.
Make sure to refer to the section describing your model.
© 2013 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
T
130817
IMPORTANT SAFETY NOTICE
The LCD panel is manufactured to provide many years of useful life.
Occasionally a few non active pixels may appear as a tiny spec of color.
This is not to be considered a defect in the LCD screen.
Proper service and repair is important to the safe, reliable operation of all
P&F Equipment. The service procedures recommended by P&F and
described in this service manual are effective methods of performing
service operations. Some of these service special tools should be used
when and as recommended.
It is important to note that this service manual contains various CAUTIONS
and NOTICES which should be carefully read in order to minimize the risk
of personal injury to service personnel. The possibility exists that improper
service methods may damage the equipment. It also is important to
understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE.
P&F could not possibly know, evaluate and advice the service trade of all
conceivable ways in which service might be done or of the possible
hazardous consequences of each way. Consequently, P&F has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a
service procedure or tool which is not recommended by P&F must first use
all precautions thoroughly so that neither his safety nor the safe operation
of the equipment will be jeopardized by the service method selected.
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Electrical Adjustment Instructions [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
[TYPE B, C]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
How to Initialize the LCD TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Firmware Renewal Mode [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
[TYPE B, C] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Block Diagrams [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
[TYPE B]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6
[TYPE C]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Wiring Diagrams[TYPE A]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
[TYPE B]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2
[TYPE C]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3
Exploded Views [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
[TYPE B, C] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1
SPECIFICATIONS
< TUNER / NTSC >
Description Condition Unit Nominal Limit
1. AFT Pull-In Range TV.ch.4 MHz ±2.3 ±2.1
TV.ch.4
2. Synchronizing Sens.
CA.ch.31
CA.ch.87
< TUNER / ATSC >
Description Condition Unit Nominal Limit
1. Received Freq. Range (-28dBm) --- kHz --- ±100
ch.4
2. ATSC Dynamic Range (min / max)
ch.10
ch.41
< LCD PANEL >
Description Condition Unit Nominal Limit
1. Native Pixel Resolution
2. Brightness (w / filter) ---
3. Viewing Angle
Horizontal
Vertical
Horizontal
Vertical
dBμV
dBμV
dBμV
dBm
dBm
dBm
pixels
pixels
cd/m
°
°
18
18
18
---
---
---
1920
1080
2
300 ---
-88 to 88
-88 to 88
20
20
23
-76/0
-76/0
-76/+4
---
---
---
---
< VIDEO >
Description Condition Unit Nominal Limit
1. Over Scan
2. Color Temperature
3. Resolution (composite video)
Horizontal
Vertical
--x
y
<Measurement Condition>
Input signal: HDMI1 Raster (40/80IRE) 1080i@60
Measurement point: Screen Center
Measuring instrument: Made of KONICA MINOLTA Luminance meter CA-310
Aging Time: 60min. (Retail MODE/100IRE Raster HDMI
MODE setting of TV: Shipment setting/Retail MODE
Ambient temperature:25°C ± 5°C
Horizontal
Vertical
%
%
°K 12000
1080i@60)
line
line
5
5
0.272
0.278
400
350
5±5
5±5
--±5%
±5%
---
---
< AUDIO >
All items are measured across 8 Ω load at speaker output terminal with L.P.F.
Description Condition Unit Nominal Limit
1.
Audio Output 10% Distortion
(ATSC 0dBfs)
2. Audio Distortion (NTSC) 500mW: Lch/Rch % 0.5/0.5 2.0/2.0
Lch/Rch W 8.0/8.0 7.0/7.0
1-1 PL13.11SP
IMPORTANT SAFETY PRECAUTIONS
ALSO TEST WITH
PLUG REVERSED
USING AC
ADAPTER PLUG
AS REQUIRED
TEST ALL EXPOSED
METAL SURFACES
READING SHOULD
NOT BE ABOVE 0.5 mA
EARTH
GROUND
_
DEVICE
LEAKAGE
CURRENT
TESTER
+
BEING
TESTED
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical
codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally
important to implement the following precautions when a set is being serviced.
Safety Precautions for LCD TV
Circuit
1. Before returning an instrument to the
customer, always make a safety check of the
entire instrument, including, but not limited to, the
following items:
a. Be sure that no built-in protective devices are
defective and have been defeated during
servicing. (1) Protective shields are provided
on this chassis to protect both the technician
and the customer. Correctly replace all missing
protective shields, including any removed for
servicing convenience. (2) When reinstalling
the chassis and/or other assembly in the
cabinet, be sure to put back in place all
protective devices, including but not limited to,
nonmetallic control knobs, insulating
fishpapers, adjustment and compartment
covers/shields, and isolation resistor/capacitor
networks. Do not operate this instrument or
permit it to be operated without all
protective devices correctly installed and
functioning. Servicers who defeat safety
features or fail to perform safety checks
may be liable for any resulting damage.
b. Be sure that there are no cabinet openings
through which an adult or child might be able to
insert their fingers and contact a hazardous
voltage. Such openings include, but are not
limited to, (1) spacing between the Liquid
Crystal Panel and the cabinet mask, (2)
excessively wide cabinet ventilation slots, and
(3) an improperly fitted and/or incorrectly
secured cabinet back cover.
c. Antenna Cold Check - With the instrument AC
plug removed from any AC source, connect an
electrical jumper across the two AC plug
prongs. Place the instrument AC switch in the
on position. Connect one lead of an ohmmeter
to the AC plug prongs tied together and touch
the other ohmmeter lead in turn to each tuner
antenna input exposed terminal screw and, if
applicable, to the coaxial connector. If the
measured resistance is less than 1.0 megohm
or greater than 5.2 megohm, an abnormality
exists that must be corrected before the
instrument is returned to the customer. Repeat
this test with the instrument AC switch in the off
position.
d. Leakage Current Hot Check - With the
instrument completely reassembled, plug the
AC line cord directly into a 120 V AC outlet. (Do
not use an isolation transformer during this
test.) Use a leakage current tester or a
metering system that complies with American
National Standards Institute (ANSI) C101.1
Leakage Current for Appliances and
Underwriters Laboratories (UL) 1410, (50.7).
With the instrument AC switch first in the on
position and then in the off position, measure
from a known earth ground (metal water pipe,
conduit, etc.) to all exposed metal parts of the
instrument (antennas, handle brackets, metal
cabinet, screw heads, metallic overlays, control
shafts, etc.), especially any exposed metal
parts that offer an electrical return path to the
chassis. Any current measured must not
exceed 0.5 milli-ampere. Reverse the
instrument power cord plug in the outlet and
repeat the test.
ANY MEASUREMENTS NOT WITHIN THE
LIMITS SPECIFIED HEREIN INDICATE A
POTENTIAL SHOCK HAZARD THAT MUST
BE ELIMINATED BEFORE RETURNING THE
INSTRUMENT TO THE CUSTOMER OR
BEFORE CONNECTING THE ANTENNA OR
ACCESSORIES.
2. Read and comply with all caution and safety-
related notes on or inside the receiver cabinet, on
the receiver chassis, or on the Liquid Crystal
Panel.
2-1 LTVN_ISP
3. Design Alteration Warning - Do not alter or add
to the mechanical or electrical design of this TV
receiver. Design alterations and additions,
including, but not limited to circuit modifications
and the addition of items such as auxiliary audio
and/or video output connections, might alter the
safety characteristics of this receiver and create a
hazard to the user. Any design alterations or
additions will void the manufacturer's warranty and
may make you, the servicer, responsible for
personal injury or property damage resulting
therefrom.
4. Hot Chassis Warning a. Some TV receiver chassis are electrically
connected directly to one conductor of the AC
power cord and maybe safety-serviced without
an isolation transformer only if the AC power
plug is inserted so that the chassis is
connected to the ground side of the AC power
source. To confirm that the AC power plug is
inserted correctly, with an AC voltmeter,
measure between the chassis and a known
earth ground. If a voltage reading in excess of
1.0 V is obtained, remove and reinsert the AC
power plug in the opposite polarity and again
measure the voltage potential between the
chassis and a known earth ground.
b. Some TV receiver chassis normally have 85V
AC(RMS) between chassis and earth ground
regardless of the AC plug polarity. This chassis
can be safety-serviced only with an isolation
transformer inserted in the power line between
the receiver and the AC power source, for both
personnel and test equipment protection.
c. Some TV receiver chassis have a secondary
ground system in addition to the main chassis
ground. This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulation material that must not be defeated or
altered.
5. Observe original lead dress. Take extra care to
assure correct lead dress in the following areas: a.
near sharp edges, b. near thermally hot parts-be
sure that leads and components do not touch
thermally hot parts, c. the AC supply, d. high
voltage, and, e. antenna wiring. Always inspect in
all areas for pinched, out of place, or frayed wiring.
Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to
have overheated or are otherwise damaged
should be replaced with components, parts, or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.
7. Product Safety Notice - Some electrical and
mechanical parts have special safety-related
characteristics which are often not evident from
visual inspection, nor can the protection they give
necessarily be obtained by replacing them with
components rated for higher voltage, wattage, etc.
Parts that have special safety characteristics are
identified by a # on schematics and in parts lists.
Use of a substitute replacement that does not
have the same safety characteristics as the
recommended replacement part might create
shock, fire, and/or other hazards. The product's
safety is under review continuously and new
instructions are issued whenever appropriate.
Prior to shipment from the factory, our products
are strictly inspected to confirm they comply with
the recognized product safety and electrical codes
of the countries in which they are to be sold.
However, in order to maintain such compliance, it
is equally important to implement the following
precautions when a set is being serviced.
2-2 LTVN_ISP
Precautions during Servicing
A. Parts identified by the # symbol are critical for
safety.
Replace only with part number specified.
B. In addition to safety, other parts and assemblies
are specified for conformance with regulations
applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise
blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before
soldering.
F. Observe that the wires do not contact heat
producing parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp
edged or pointed parts.
H. When a power cord has been replaced, check that
11~13 lb (5~6 kg) of force in any direction will not
loosen it.
I. Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder
droplets, etc.) do not remain inside the set.
K. When connecting or disconnecting the internal
connectors, first, disconnect the AC plug from the
AC supply outlet.
L. When installing parts or assembling the cabinet
parts, be sure to use the proper screws and
tighten certainly.
2-3 LTVN_ISP
Safety Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and
wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified
values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d') between
soldered terminals, and between terminals and
surrounding metallic parts. (See Fig. 1)
Table 1: Ratings for selected area
Chassis or Secondary Conductor
Primary Circuit
AC Line Voltage Region
110 to 130 V
Note: This table is unofficial and for reference only. Be
sure to confirm the precise values.
U.S.A. or
Canada
Clearance
Distance (d), (d’)
≥ 3.2 mm
(0.126 inches)
2. Leakage Current Test
Confirm the specified (or lower) leakage current
between B (earth ground, power cord plug prongs) and
externally exposed accessible parts (RF terminals,
antenna terminals, video and audio input and output
terminals, microphone jacks, earphone jacks, etc.) is
lower than or equal to the specified value in the table
below.
Measuring Method: (Power ON)
Insert load Z between B (earth ground, power cord plug
prongs) and exposed accessible parts. Use an AC
voltmeter to measure across both terminals of load Z.
See Fig. 2 and following table.
d' d
Fig. 1
Exposed Accessible Part
Z
AC Voltmeter
(High Impedance)
Earth Ground
B
Power Cord Plug Prongs
Table 2: Leakage current ratings for selected areas
AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to:
110 to 130 V
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
U.S.A. or
Canada
0.15 μF CAP. & 1.5 kΩ RES.
Connected in parallel
2-4 LTVN_ISP
i ≤ 0.5 mA rms
Fig. 2
Exposed accessible
parts
STANDARD NOTES FOR SERVICING
Top View
Out
In
Bottom View
Input
5
10
Pin 1
Pin 1
Fig. S-1-1
Circuit Board Indications
1. The output pin of the 3 pin Regulator ICs is
indicated as shown.
2. For other ICs, pin 1 and every fifth pin are
indicated as shown.
3. The 1st pin of every male connector is indicated as
shown.
Pb (Lead) Free Solder
Pb free mark will be found on PCBs which use Pb
free solder. (Refer to figure.) For PCBs with Pb free
mark, be sure to use Pb free solder. For PCBs
without Pb free mark, use standard solder.
Pb free mark
How to Remove / Install Flat Pack-IC
1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine:
1. Prepare the hot-air flat pack-IC desoldering
machine, then apply hot air to the Flat Pack-IC
(about 5 to 6 seconds). (Fig. S-1-1)
2. Remove the flat pack-IC with tweezers while
applying the hot air.
3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
CAUTION:
1. The Flat Pack-IC shape may differ by models. Use
an appropriate hot-air flat pack-IC desoldering
machine, whose shape matches that of the Flat
Pack-IC.
2. Do not supply hot air to the chip parts around the
flat pack-IC for over 6 seconds because damage
to the chip parts may occur. Put masking tape
around the flat pack-IC to protect other parts from
damage. (Fig. S-1-2)
3-1 TVN_SN
3. The flat pack-IC on the CBA is affixed with glue, so
Hot-air
Flat Pack-IC
Desoldering
Machine
CBA
Flat Pack-IC
Tweezers
Masking
Tape
Fig. S-1-2
Flat Pack-IC
Desoldering Braid
Soldering Iron
Fig. S-1-3
Fine Tip
Soldering Iron
Sharp
Pin
Fig. S-1-4
be careful not to break or damage the foil of each
pin or the solder lands under the IC when
removing it.
With Soldering Iron:
1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
2. Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)
3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
3-2 TVN_SN
With Iron Wire:
To Solid
Mounting Point
Soldering Iron
Iron Wire
or
Hot Air Blower
Fig. S-1-5
Fine Tip
Soldering Iron
CBA
Flat Pack-IC
Tweezers
Fig. S-1-6
Example :
Pin 1 of the Flat Pack-IC
is indicated by a " " mark.
Fig. S-1-7
1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
2. Affix the wire to a workbench or solid mounting
point, as shown in Fig. S-1-5.
3. While heating the pins using a fine tip soldering
iron or hot air blower, pull up the wire as the solder
melts so as to lift the IC leads from the CBA
contact pads as shown in Fig. S-1-5.
4. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
5. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be
taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.
2. Installation
1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA
so you can install a replacement flat pack-IC more
easily.
2. The “ I ” mark on the flat pack-IC indicates pin 1.
(See Fig. S-1-7.) Be sure this mark matches the
pin 1 on the PCB when positioning for installation.
Then presolder the four corners of the flat pack-IC.
(See Fig. S-1-8.)
3. Solder all pins of the flat pack-IC. Be sure that
none of the pins have solder bridges.
Presolder
Flat Pack-IC
CBA
Fig. S-1-8
3-3 TVN_SN
Instructions for Handling Semi-
<Incorrect>
CBA
Grounding Band
Conductive Sheet or
Copper Plate
1MΩ
1MΩ
<Correct>
CBA
conductors
Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 MΩ) that is
properly grounded to remove any static electricity that
may be charged on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate
with proper grounding (1 MΩ) on the workbench or
other surface, where the semi-conductors are to be
placed. Because the static electricity charge on
clothing will not escape through the body grounding
band, be careful to avoid contacting semi-conductors
with your clothing.
3-4 TVN_SN
CABINET DISASSEMBLY INSTRUCTIONS
[2] Stand Base
Assembly
[3] Rear Cover
[4] Power Supply
CBA
[6] Stand Bracket
[7] Speaker
[5] Digital Main
CBA Unit
[8] LCD Panel
Assembly
[9] X-PCB Cover
[1] Stand Neck
Assembly
[10] Front Cabinet
[11] Function
CBA Unit
Screw Torque Specification
Ref.
No.
L9 GBHP3120
L23 GBJS3060
L27 GBHS3080
L35 GBJB3080
L67 GBJS3100
SSK1 1ESA34647
SSK2 1ESA34648
* For reference
Part
Number
Part Name
SCREW P-TIGHT
(3X12 BIND HEAD +
BLK)
SCREW S-TIGHT
(M3X6 BIND HEAD+)
SCREW S-TIGHT
(M3X8 BIND HEAD+)
SCREW B-TIGHT
(D3X8 BIND HEAD+)
SCREW S-TIGHT
(M3X10 BIND HEAD+)
STAND SCREW KIT
(DOUBLE SEMS
SCREW M4X20 + BLK)
STAND SCREW KIT
(DOUBLE SEMS
SCREW M4X10 + BLK)
Tightening
Tor que
5.2±0.9lb·in
6.1±0.9lb·in
5.2±0.9lb·in
6.1±0.9lb·in
(approx.
8.7±0.9lb·in
*
)
1. Disassembly Flowchart
This flowchart indicates the disassembly steps for the
cabinet parts and the CBA in order to gain access to
items to be serviced. When reassembling, follow the
steps in reverse order. Bend, route and dress the
cables as they were.
Step/
Loc.
No.
[2]
Part
Stand Base
Assembly
Fig.
No.
Removal Note
D1 --------------- ---
[3] Rear Cover D1 2(S-3), 10(S-4) ---
Power
[4]
Supply
CBA
Digital Main
[5]
CBA UnitD2D5
D2D55(S-5), CN601,
CN501, CN1001
4(S-6), CN3906
CN3013
CN3101
*2
, CN3105*1,
*2
, CN3801,
*1
,
Jack Holder
Stand
[6]
Bracket
D3 2(S-7) ---
[7] Speaker D3 --------------- ---
LCD Panel
[8]
[9]
[10]
[11]
Assembly
X-PCB
Cover
Front
Cabinet
Function
CBA Unit
D3 --------------- ---
D4 3(S-8) 1
D4 4(S-9) 2
Sensor Lens, Shield
D4
Plate, Control Plate
---
---
2
2. Disassembly Method
Step/
Loc.
No.
Stand Neck
[1]
Assembly
Part
Fig.
No.
Removal Note
D1 4(S-1), 3(S-2) ---
↓
(1)
(2)
↓
↓
(3)
↓
(4)
↓
(5)
*1: TYPE A
*2: TYPE B, C
Note:
(1) Order of steps in procedure. When reassembling,
follow the steps in reverse order. These numbers
are also used as the Identification (location) No. of
parts in figures.
(2) Parts to be removed or installed.
(3) Fig. No. showing procedure of part location
(4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
P = Spring, L = Locking Tab, S = Screw,
H = Hex Screw, CN = Connector
e.g. 2(S-2) = two Screws of (S-2),
2(L-2) = two Locking Tabs of (L-2)
(5) Refer to the following "Reference Notes in the
Ta bl e ."
4-1 PL13.11_DC
Important precautions concerning the
(S-1)
[2] Stand Base
Assembly
(S-4)
(S-3)
[3] Rear Cover
[1] Stand Neck
Assembly
(S-2)
(S-4)
(S-4)
39PFL2608/F7
39PFL2708/F7,
39PFL2908/F7,
39PFL4208/F8,
39PFL4408/F8
Fig. D1
LCD Panel Assembly:
1. When you disassemble/re-assemble the X-PCB
Cover
• Be careful not to break the hooks. If you pull with too
much force, the hooks may be damaged.
• When disassembling, first hold the top and bottom of
the X-PCB Cover on both ends and then moving
toward the center, lift up the top side to detach the
hooks.
• When assembling, be careful not to damage the
X-PCB Board or the COF(Chip On Film).
• Make sure the hooks are securely in place when
re-assembling.
• The screw tightening torque must be 5.2lb·in
(6kgf·cm).
2. When you disassemble/re-assemble the Front
Cabinet or Function CBA Unit
• Be careful not to break the hooks. If you pull with too
much force, the hooks may be damaged.
• When disassembling, first detach the hooks on each
end on the bottom side, then detach the remaining
hooks moving toward the center.
• Make sure the hooks are securely in place when
assembling.
• Be careful not to scratch the display panel when
assembling.
• The Function CBA Unit and Sensor Lens are fixed in
place by the hooks. Make sure these hooks are not
damaged. Make sure the Function CBA Unit and
Sensor Lens are securely in place when
re-assembling.
• The screw tightening torque must be 5.2lb·in
(6kgf·cm).
• After replacing the Front Cabinet or Function CBA
Unit, make sure the tact switches operate normally.
• Make sure to replace the Control Plate to a new one
when replacing the Front Cabinet.
4-2 PL13.11_DC
[4] Power Supply CBA
[5] Digital Main CBA Unit
(S-6)
(S-5)
Jack Holder
Type A
Jack Holder
Type B, C
(S-6)
Fig. D2
[7] Speaker
[6] Stand Bracket
(S-7)
[8] LCD Panel Assembly
[7] Speaker
Fig. D3
4-3 PL13.11_DC
*1: Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the
X-PCB Cover.
[11] Function CBA Unit
*
2
(S-9)
Sensor Lens
*
2
Control Plate
*
2
[10] Front Cabinet
*
2
Shield Plate
Hook
*
2
Hook
*
2
Hook
*
2
Hook
*
2
[9] X-PCB Cover
*
1
Hook
*
1
(S-8)
Hook
*
1
Hook
*
1
Fig. D4
*2: Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the Front
Cabinet or Function CBA Unit.
4-4 PL13.11_DC
TV Cable Wiring Diagram
*1: TYPE A
*2: TYPE B
*3: TYPE C
To LCD Panel
Assembly
Power Supply CBA
CN1001
CN601
CN501
*1
*2,*3
CN3105
CN3101
To LCD Panel
Assembly
Digital Main
CBA Unit
CN3906
*1
*2,*3
CN3013
CN3601
*1
CN3701
*2
CN3602
*3
CN3801
To AC Cord
Function CBA Unit
CN4052
To Speaker
Fig. D5
4-5 PL13.11_DC
ELECTRICAL ADJUSTMENT INSTRUCTIONS
[current]
File code:
Total checksum:
Panel-Option code:
Press "POWER" key to exit.
MAC address:
ESN:
**:**:**:**:**:**
*****************************
***-****
_
***_*
Push "0" key
**-***-***-***-***-***
***-***-***-***-***
Flicker:
Tuner:
HDMI UART:
Touch Sensor Ver:
EDID:
*****
****
OFF
------ / -.--.-Push "0" key
TotalWatchTime:
SystemTime:
Lightsensor:
*****
**:**
**
"*" differs depending on the models.
[7] button
Note:
When entering this mode, the default setting is White mode.
Purity Check Mode
[7] button
White 50% mode
Red, Green, Blue mode
V-ramp mode
Black mode
[7] button
White mode
[7] button
[7] button
White 20% mode
[7] button
[TYPE A]
General Note: “CBA” is abbreviation for
“Circuit Board Assembly.”
Note: Electrical adjustments are required after
replacing circuit components and certain
mechanical parts. It is important to perform
these adjustments only after all repairs and
replacements have been completed.
Also, do not attempt these adjustments unless
the proper equipment is available.
Test Equipment Required
1. Remote control unit
2. Color Analyzer,
CA-310 (KONICA MINOLTA Luminance meter) or
measuring instrument as good as CA-310.
How to set up the service mode:
Service mode:
1. Turn the power on.
2. Press [0], [6], [2], [5], [9], [6], and [INFO] buttons
on the remote control unit in this order. The
following screen appears.
1. Purity Check Mode
This mode cycles through full-screen displays of red,
green, blue, and white to check for non-active pixels.
1. Enter the service mode.
2. Each time the [7] button on the remote control unit
is pressed, the display changes as follows.
3. To cancel or to exit from the Purity Check Mode,
press [CH RETURN] or [PREV CH] button.
5-1 PL13.11 (A3RTBUH)_EA
2. VCOM Adjustment
Color Analyzer
To avoid interference from ambient
light, this adjustment should be
performed in a dark room.
Perpendicularity
Test Point Adj. Point
Screen
M. EQ. Spec.
Color analyzer See below
[CHANNEL UP/DOWN]
Figure
buttons
The White Balance Adjustment should be
performed when replacing the LCD Panel
or Digital Main CBA.
3. White Balance Adjustment
Purpose: To mix red and blue beams correctly for
pure white.
Symptom of Misadjustment: White becomes bluish
or reddish.
1. Operate the unit for more than 60 minutes.
2. Set the color analyzer at the zero point calibration
and bring the optical receptor pointing at the
center of the LCD-Panel.
Note: The optical receptor must be set
perpendicular to the LCD Panel surface.
3. Enter the service mode.
4. Press [2] button on the remote control unit.
5. Press [CHANNEL UP/DOWN] buttons on the
remote control unit so that the color analyzer value
becomes minimum.
6. To cancel or to exit from the VCOM Adjustment,
press [CH RETURN] or [PREV CH] button.
ITEM
Color temperature
Input Signal
Measurement point Screen center
M. EQ.
Aging time
MODE setting of TV
Ambient
temperature
1. Operate the unit for more than 60 minutes.
2. Enter the service mode.
3. Press [VOLUME DOWN] button three times on the
remote control unit to select “Drive setting” mode.
“Drive” appears in the screen.
4. Set the color analyzer at the CHROMA mode and
zero point calibration. Bring the optical receptor
pointing at the center of the LCD-Panel.
SPECIFICATION
x= 0.272 ± 0.005
y= 0.278 ± 0.005
Internal pattern
(30/50/80% raster)
CA-310 (KONICA MINOLTA
Luminance meter) or
measuring instrument as
good as CA-310.
60min.
(Retail MODE/100IRE Raster
HDMI 1080i@60)
Shipment setting/
Retail MODE
25°C ± 5°C
To avoid interference from ambient
light, this adjustment should be
performed in a dark room.
Perpendicularity
Color Analyzer
Note: The optical receptor must be set
perpendicularly to the LCD Panel surface.
5-2 PL13.11 (A3RTBUH)_EA
5. Press [3] button to select the “HDB” for High Drive
Internal (Single)
HDB 0
Internal (Single)
MDB 0
Internal (Single)
LDB 0
Blue adjustment. (“HDB” appears in the screen.)
6. Press [MENU] button. The internal Raster signal
appears in the screen. (“Internal (Single)” appears
in the upper right of the screen as shown below.)
7. Press [CHANNEL UP/DOWN] buttons to adjust
the color temperature becomes 12000°K
(x
=
0.272 / y= 0.278 ± 0.005).
8. Press [1] button to select the “HDR” for High Drive
Red adjustment (“HDR” appears in the screen.)
and press [CHANNEL UP/DOWN] buttons to
adjust the color temperature.
9. If necessary, adjust the “HDB” or “HDR” again.
10. Press [6] button to select the “MDB” for Middle
Drive Blue adjustment (“MDB” appears in the
screen.) and press [CHANNEL UP/DOWN] buttons
to adjust the color temperature.
13. Press [9] button to select the “LDB” for Low Drive
Blue adjustment (“LDB” appears in the screen.)
and press [CHANNEL UP/DOWN] buttons to
adjust the color temperature.
14. Press [7] button to select the “LDR” for Low Drive
Red adjustment (“LDR” appears in the screen.) and
press [CHANNEL UP/DOWN] buttons to adjust the
color temperature.
15. If necessary, adjust the “LDB” or “LDR” again.
16. Press [CH RETURN] or [PREV CH] to shift to the
initial screen in the service mode.
If [White Balance] message with a green color is
displayed on the upper right of the screen, this
adjustment completes.
If [White Balance] message with a red color is
displayed, repeat above steps from 5. to 15. Then
check the initial screen in the service mode again.
If [White Balance] message with a red color is
displayed, replace the LCD Panel or Digital Main
CBA.
17. To cancel or to exit from the White Balance
Adjustment, press [CH RETURN] or [PREV CH]
button.
11. Press [4] button to select the “MDR” for Middle
Drive Red adjustment (“MDR” appears in the
screen.) and press [CHANNEL UP/DOWN] buttons
to adjust the color temperature.
12. If necessary, adjust the “MDB” or “MDR” again.
5-3 PL13.11 (A3RTBUH)_EA
[TYPE B, C]
Code:
Pic code:
Panel-Option code:
MIPS:
Press "POWER" key to exit.
*******-**-**-****-**
***-*****-***-***-*-**
**-***-***-***-***
Push 0 key
Safety:
HDMI EDID:
HDMI UART:
Touch Sensor Ver:
Safety_Non
**
OFF
-.-- / ---
Total Watch Time:
Lightsensor:
*****
**
"*" differs depending on the models.
How to set up the service mode:
General Note: “CBA” is abbreviation for
“Circuit Board Assembly.”
Note: Electrical adjustments are required after
replacing circuit components and certain
mechanical parts. It is important to perform
these adjustments only after all repairs and
replacements have been completed.
Also, do not attempt these adjustments unless
the proper equipment is available.
Test Equipment Required
1. Remote control unit
2. Color Analyzer,
CA-310 (KONICA MINOLTA Luminance meter) or
measuring instrument as good as CA-310.
Service mode:
1. Turn the power on.
2. Press [MENU] button to display Setup menu.
3. Select “Features”.
4. Select “Software Upgrade”.
5. Select “Current Software Info”.
6. Press [0], [6], [2], [5], [9], [6] and [INFO] buttons on
the remote control unit in this order. The following
screen appears.
5-4 PL13.7EA
1. Purity Check Mode
[7] button
Note:
When entering this mode, the default setting is White mode.
Purity Check Mode
[7] button
White 50% mode
Red, Green, Blue mode
V-ramp mode
Black mode
[7] button
White mode
[7] button
[7] button
White 20% mode
[7] button
Color Analyzer
To avoid interference from ambient
light, this adjustment should be
performed in a dark room.
Perpendicularity
2. VCOM Adjustment
This mode cycles through full-screen displays of red,
green, blue, and white to check for non-active pixels.
1. Enter the service mode.
2. Each time the [7] button on the remote control unit
is pressed, the display changes as follows.
Test Point Adj. Point
Screen
[CHANNEL UP/DOWN]
buttons
M. EQ. Spec.
Color analyzer See below
Figure
1. Operate the unit for more than 60 minutes.
2. Set the color analyzer at the zero point calibration
and bring the optical receptor pointing at the
center of the LCD-Panel.
Note: The optical receptor must be set
perpendicular to the LCD Panel surface.
3. Enter the service mode.
4. Press [2] button on the remote control unit.
5. Press [CHANNEL UP/DOWN] buttons on the
remote control unit so that the color analyzer value
becomes minimum.
6. To cancel or to exit from the VCOM Adjustment,
press [CH RETURN] or [PREV CH] button.
3. To cancel or to exit from the Purity Check Mode,
press [CH RETURN] or [PREV CH] button.
5-5 PL13.7EA
The White Balance Adjustment should be
Color Analyzer
Perpendicularity
To avoid interference from ambient
light, this adjustment should be
performed in a dark room.
Internal (Single)
HDB 0
Internal (Single)
LDB 0
performed when replacing the LCD Panel
or Digital Main CBA.
3. White Balance Adjustment
Purpose: To mix red and blue beams correctly for
pure white.
Symptom of Misadjustment: White becomes bluish
or reddish.
6. Press [MENU] button. The internal Raster signal
appears in the screen. (“Internal (Single)” appears
in the upper right of the screen as shown below.)
ITEM
Color temperature
Input Signal
SPECIFICATION
x= 0.272 ± 0.005
y= 0.278 ± 0.005
Internal pattern
(40/80% raster)
Measurement point Screen center
CA-310 (KONICA MINOLTA
M. EQ.
Luminance meter) or
measuring instrument as
good as CA-310.
60min.
Aging time
(Retail MODE/100IRE Raster
HDMI 1080i@60)
MODE setting of TV
Ambient
temperature
Shipment setting/
Retail MODE
25°C ± 5°C
1. Operate the unit for more than 60 minutes.
2. Enter the service mode.
3. Press [VOLUME DOWN] button three times on the
remote control unit to select “Drive setting” mode.
“Drive” appears in the screen.
4. Set the color analyzer at the CHROMA mode and
zero point calibration. Bring the optical receptor
pointing at the center of the LCD-Panel.
Note: The optical receptor must be set
perpendicularly to the LCD Panel surface.
5. Press [3] button to select the “HDB” for High Drive
Blue adjustment. (“HDB” appears in the screen.)
7. Press [CHANNEL UP/DOWN] buttons to adjust
the color temperature becomes 12000°K
(x
=
0.272 / y= 0.278 ± 0.005).
8. Press [1] button to select the “HDR” for High Drive
Red adjustment (“HDR” appears in the screen.)
and press [CHANNEL UP/DOWN] buttons to
adjust the color temperature.
9. If necessary, adjust the “HDB” or “HDR” again.
10. Press [6] button to select the “LDB” for Low Drive
Blue adjustment (“LDB” appears in the screen.)
and press [CHANNEL UP/DOWN] buttons to
adjust the color temperature.
11. Press [4] button to select the “LDR” for Low Drive
Red adjustment (“LDR” appears in the screen.)
and press [CHANNEL UP/DOWN] buttons to
adjust the color temperature.
12. If necessary, adjust the “LDB” or “LDR” again.
13. Press [VOLUME DOWN] button to shift to the
“Debugging Message” mode.
If there is no message under “[WB]” section, this
adjustment completes.
If “Drive settings are NG. Retry again.” is
displayed, repeat above steps from 5. to 12. Then
check “Debugging Message” again. If “Drive
settings are NG. Retry again.” is displayed, replace
the LCD Panel or Digital Main CBA.
14. To cancel or to exit from the White Balance
Adjustment, press [CH RETURN] or [PREV CH]
button.
5-6 PL13.7EA
HOW TO INITIALIZE THE LCD TV
The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to
select a language and program channels after the set has been initialized.
To put the program back at the factory-default, initialize the LCD TV using the following procedure.
NOTE: Disconnect any device from the USB Port
before you conduct on this procedure.
[TYPE A]
1. Turn the power on.
2. Enter the service mode.
- To cancel the service mode, press [ ] button on
the remote control unit.
3. Press [BACK] button to enter the Control Panel
Key Confirmation Menu.
4. Press any button on the control panel.
5. Press [INFO] button to proceed with the self check
mode.
6. Make sure to confirm the “INITIALIZED : OK”
appears in the green screen.
7. Unplug the AC Cord and plug it back on again.
[TYPE B, C]
1. Turn the power on.
2. Enter the service mode.
- To cancel the service mode, press [ ] button on
the remote control unit.
3. Press [BACK] button to enter the Panel Key
Confirmation Menu.
4. Press any button on the control panel.
5. Press [INFO] button to proceed with the self check
mode.
6. Make sure to confirm the “INITIALIZED FINISH”
appears in the green screen.
7. Unplug the AC Cord and plug it back on again.
6-1 PL13.11_INT
FIRMWARE RENEWAL MODE
USB port
USB storage
device
Rear Cabinet
(example)
Select an upgrade file
Cancel
*****_******.upg
*****_******.upg
*****_******.upg
"*" differs depending on the models.
123
Are you sure you want to update?
No Yes
Current Version: ***-****-***-*
New Version: ***-****-***-*
"*" differs depending on the models.
[TYPE A]
Equipment Required
1. USB storage device
2. Remote Control Unit
Firmware Update Procedure
1. Turn the power off and unplug the AC Cord.
2. Insert the USB storage device to the USB port as
shown below.
Update file selection screen appears as follows.
(Files included in the USB storage device are
displayed.
Note:
To cancel the update mode, select “Cancel” and
press the [OK] button.
10. Select the file and press [OK] button.
11. The update will start and the following will appear
in the screen.
3. Plug the AC Cord and turn the power on.
4. After few seconds, the menu mode will appear in
the screen.
Note:
After 30 seconds without an operation, the menu
mode will disappear automatically.
To display the menu mode again, press the
[MENU] button on the remote control unit.
5. Select “Setup” and press the [OK] button to display
the setup menu.
6. Select “Software”.
7. Select “Software update”.
8. Select “USB”.
9. Press the [OK] button on the remote control unit to
enter the update mode.
Note:
If the above screen isn’t displayed, repeat from
step 1.
12. Select “Yes” and press the [OK] button to update.
Note:
Do not remove the USB storage device or turn the
TV off while update is in progress.
13. When the firmware update is completed, the
following will appear in the screen.
Update your TV with new software: Done
Software update is successful.
Please remove the USB storage device
and restart the TV set.
Remove the USB storage device from the USB
port.
Turn the power off and turn the power on again.
7-1 PL13.11 (A3RTBUH)_FW
[TYPE B, C]
USB port
USB storage
device
Rear Cabinet
(example)
Software upgrade in progress. Please wait.
Do not remove the USB storage device or
turn the TV off while upgrade is in progress.
Software Upgrade
Downloading...
Current Version:
New Version:
*******-***-*-***-****
*******-***-*-***-****
0%
*1
"*" differs depending on the models.
Software Upgrade
The software upgrade is completed.
Remove USB storage device, turn TV off then on again.
Equipment Required
a. USB storage device
b. Remote Control Unit
Firmware Update Procedure
User Upgrade (Filename example: TVNB012_00_PF_XX91_BC.ecc or TVNB1012_00_PG_XX91_BA0.bin)
Upgrade the firmware only. The setting values will not be initialized.
The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to
upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename.
If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_” from the
filename.
Update procedure
1. Turn the power on.
2. Press [MENU] button to display Menu.
3. Select “Features”.
4. Select “Software Upgrade”.
5. Select “Upgrade” to display Upgrade screen.
6. Press [OK] button to display Software Upgrade
screen.
7. Select “USB” and press [OK] button.
8. Insert the USB storage device to the USB port as
shown below.
11. The update will start and the following will appear
in the screen.
9. Select “Check” and press [OK] button.
10. Select “Upgrade” and press [OK] button to start
software upgrade.
Note: If the above screen isn’t displayed, repeat from
step 1.
The appearance shown in *1 is described as follows.
Appearance State
Downloading...
Writing...
Downloading the firmware from
the USB storage device.
Writing the downloaded firmware
in flash memory.
Checking... Checking the new firmware.
12. When the firmware update is completed, the
following will appear in the screen.
Remove the USB storage device from the USB
port.
Turn the power off and turn the power on again.
7-2 PL13.11FW
Factory Upgrade (Firmware Upgrade/Flash Upgrade)
USB port
USB storage
device
Rear Cabinet
(example)
Software upgrade in progress. Please wait.
Do not remove the USB storage device or
turn the TV off while upgrade is in progress.
Software Upgrade
Downloading...
Current Version:
New Version:
*******-***-*-***-****
*******-***-*-***-****
0%
*1
"*" differs depending on the models.
Software Upgrade
The software upgrade is completed.
Remove USB storage device, turn TV off then on again.
Firmware Upgrade
(Filename example: FACT_TVNB012_00_PF_XX91_BC.ecc or FACT_TVNB1012_00_PG_XX91_BA0.bin)
Upgrade the firmware and initialize the setting values.
The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to
upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename.
If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_” from the
filename.
Flash Upgrade
(Filename example: ALL_TVNB012_00_PF_XX91_BC.ecc or ALL_TVNB1012_00_PG_XX91_BA0.bin)
Upgrade the firmware and initialize the setting values along with the factory default such as White Balance, etc.
Before the upgrade, you will need to make a note of all the factory default so you will be able to set it back on the
TV after the initialization.
The Flash Upgrade will be done by it's unique file.
The User Upgrade/Firmware Upgrade (Factory Upgrade) file cannot be used for this upgrade.
Update procedure
1. Turn the power off.
2. Insert the USB storage device to the USB port as
shown below.
The appearance shown in *1 is described as follows.
Appearance State
Downloading...
Writing...
Downloading the firmware from
the USB storage device.
Writing the downloaded firmware
in flash memory.
Checking... Checking the new firmware.
3. Turn the power on.
4. The update will start and the following will appear
in the screen.
Note: If the above screen isn’t displayed, repeat from
step 1.
5. When the firmware update is completed, the
following will appear in the screen.
Remove the USB storage device from the USB
port.
Turn the power off and turn the power on again.
Service mode initial screen with a word
“INITIALIZED” will appear in the screen. The color
of the word “INITIALIZED” will change from red to
green when initialization is completed.
7-3 PL13.11FW
[Power Supply Section]
FLOW CHART NO.1
The power cannot be turned on.
TROUBLESHOOTING
Is the fuse (F602) normal?
Ye s
Is normal state restored when once unplugged
power cord is plugged again after several seconds?
Ye s
Is the P-ON+21V line voltage normal?
Ye s
Check each rectifying circuit of the secondary
circuit and repair it if defective.
FLOW CHART NO.2
The fuse blows out.
Check if there is any leak or short-circuit on the
primary circuit component and repair it if defective.
Make sure to repair the pr
imary circuit component before replacing the fuse
No
No
No
See FLOW CHART No.2 <The fuse blows out.>
Check if there is any leak or short-circuit on the
primary circuit component and repair it if defective.
(C607, C612, D601, D602, D603, D604, D605, D606,
D607A, D608, D609A, D621, D623, Q601, Q602,
Q621, R611, R619, T601)
Check if there is any leak or short-circuit on the
each rectifying circuit component of secondary side
and repair it if defective.
(F602).
FLOW CHART NO.3
When the output voltage fluctuates.
Does the photocoupler circuit on the secondary side
operate normally?
Ye s
Check IC602, D605, D607A, D608, D609A, D610, D621,
D623, Q601, Q602, Q621 and their per
Repair it if defective.
FLOW CHART NO.4
When buzz sound can be heard in the periphery of power circuit.
Check if there is any short-circuit on the rectifying diode and the circ
Repair it if defective. (D650, D651, D653, D
iphery circuit.
655, D659, Q658, (IC651, Q657))
No
Check IC602, D652, D654, D660, D661, Q653 and
their periphery circuit. Repair it if defective.
uit in each rectifying circuit of the secondary side.
8-1 PL13.11ATR
FLOW CHART NO.5
P-ON+21V is not output.
Is approximately +21V voltage supplied to the cathode
of D650(D651, D659)?
Ye s
Check if there is any leak or short-circuit on the load
circuit. Repair it if defective.
FLOW CHART NO.6
AMP+13V is not output.
Is approximately +12V voltage supplied to the cathode
of D653(D655)?
Ye s
Check if there is any leak or short-circuit on the load
circuit. Repair it if defective.
FLOW CHART NO.7
[TYPE A]
AL+3.3V is not output.
Is approximately +12V voltage supplied to the emitter
of Q658?
Ye s
Is approximately +11V voltage supplied to the base of
Q658?
Ye s
No
No
No
No
Check D650, D651, D652, D659, C651, C652,
C653, C667, C668 and their periphery circuit.
Repair it if defective.
Check D653, D654, D655, C654, C655 and their
periphery circuit. Repair it if defective.
Check D653, D654, D655, C654, C655, R690 and
their periphery circuit. Repair it if defective.
Check D662, Q656 and their periphery circuit.
Repair it if defective.
Replace Q658.
[TYPE B]
AL+3.3V is not output.
Is approximately +12V voltage supplied to Pin(3) of
IC651?
Ye s
Replace IC651
[TYPE C]
AL+3.3V is not output.
Is approximately +11V voltage supplied to the emitter
of Q657 and Pin(3) of IC651?
Ye s
Is approximately +3.3V voltage supplied to the collector
of Q657?
Ye s
Replace IC651.
No
No
No
Check D653, D654, D655, C654, C655, R676, R678,
R679, R683, R684 and their periphery circuit.
Repair it if defective.
Check D653, D654, D655, C654, C655, R676, R678,
R679, R683, R684, R688, R689 and their periphery
circuit. Repair it if defective.
Replace Q657.
8-2 PL13.11ATR
[Video Signal Section]
FLOW CHART NO.1
The key operation is not functioning.
When touching each buttons, does the Pin(6) voltage
of CN4052 decrease?
Ye s
Replace the Digital Main CBA Unit.
FLOW CHART NO.2
No operation is possible from the remote control unit. (Operation is possible from the unit.)
Is approximately +3.3V voltage supplied to Pin(1) of
CN4052?
Ye s
Is the "L" pulse supplied to Pin(5) of CN4052 when the
remote control unit is activated?
Ye s
Replace the Digital Main CBA Unit.
No
No
No
Replace the Function CBA Unit.
Check AL+3.3V line and repair it if defective.
Replace the Function CBA Unit.
FLOW CHART NO.3
Picture does not appear normally.
Is approximately +21V voltage supplied to
Pin(20, 21, 22, 23) of CN501?
Ye s
Is
approximately +
CN501?
Digital Main CBA Unit or LCD Panel Assembly may
be defective.
Check and replace these parts.
3.3V voltage supplied to Pin(8) of
Ye s
No
No
See FLOW CHART NO.5 <P-ON+21V is not output.
[Power Supply Section]>
See FLOW CHART NO.7 <AL+3.3V is not output.
[Power Supply Section]>
8-3 PL13.11ATR
[Audio Signal Section]
FLOW CHART NO.1
Audio is not output normally.
Is approximately +12V voltage supplied to
Pin(15, 16, 17, 18) of CN501?
Ye s
approximately +
Is
CN501?
Are the audio signals output to Pin(1, 2, 3, 4) of CN3801?
SP3801, SP3802 or CL3801 may be defective.
Check and replace these parts.
3.3V voltage supplied to Pin(8) of
Ye s
Ye s
No
No
No
See FLOW CHART NO.6 <AMP+13V is not output.
[Power Supply Section]>
See FLOW CHART NO.7 <AL+3.3V is not output.
[Power Supply Section]>
Replace the Digital Main CBA Unit.
8-4 PL13.11ATR
BLOCK DIAGRAMS
[TYPE A]
1. System Control Block Diagram
P-ON+5V
KEY SWITCH
LIGHT
POWER
IC4051
SENSOR
REMOTE
RS4051
D4051
SENSOR
CN4052
FUNCTION CBA UNIT
TO
POWER SUPPLY
BLOCK DIAGRAM
TO
LED BACKLIGHT DRIVE
BLOCK DIAGRAM
RESET
P-ON-H2
PROTECT3
BACKLIGHT-SW
BACKLIGHT-ADJ
CN501
CN501
P-ON-H2
RESET
PROTECT3
BACKLIGHT-SW
66
44
CN3601
BACKLIGHT-ADJ
33
55
77
CN3601
POWER SUPPLY CBA
IC3101
(MAIN MICRO CONTROLLER)
TX(+)
AD6
TX(-)
AE6
RX(+)
AC7
KEY-IN146
REMOTE55
LED164
LIGHT73
CN3105
Q3101
LED DRIVE
BUFFER
Q3102
T3
V3
U3
U1
LED1
LIGHT
KEY-IN1
REMOTE
USB0(-)
USB0(+)
RX(-)
N22
M24
AC8
(MEMORY)
IC3103
USB1(+)
L23
SCL
SDA
6
5
AC2
AC1
STM-SCL
STM-SDA
USB1(-)
M22
VGA-SCL
Y7
VGA-SDA
LCD-P-ON
W2
AD3
COMP-DET
HP-DET
L2
H6
RESET
Y2
AD5
P-ON-H2
STB-RESET
TU-SCL
Y15
4
SCL
IC3601
TU-SDA
AA16
3
SDA
T2
W3
PROTECT3
BACKLIGHT-SW
P7
BACKLIGHT-ADJ
X3101
AXO
AXI
AE4
AD4
25MHz
OSC
DIGITAL MAIN CBA UNIT
RX(-)
USB0(+)
CN3704
USB JACK
TX(+)
CN3706
TX(-)
RX(+)
ETHERNET
JACK
USB0(-)
USB1(+)
WIRELESS
CN3701
USB1(-)
LAN MODULE
VGA-SCL
VGA-SDA
9-1
HP-DET
LCD-P-ON
COMP-DET
TO VIDEO/AUDIO
BLOCK DIAGRAM
TU3001 (TUNER UNIT)
PL13.11ABLS
2. Video/Audio Block Diagram
AUDIO SIGNAL
VIDEO SIGNAL
VGA-R-IN
VGA-B-IN
VGA-G-IN
VGA-VSYNC
VGA-HSYNC
IF-AGC
DIF-OUT1
DIF-OUT2
COM-VIDEO-Pr-IN
COM-VIDEO-Pb-IN
COM-VIDEO-Y/VIDEO-IN
TO DIGITAL
SIGNAL PROCESS
BLOCK DIAGRAM
AUDIO(L)-IN
AUDIO(R)-IN
SPDIF
HP(R)
HP(L)
AMP(L)-OUT
3
VGA-SCL
VGA-SDA
AMP(R)-OUT
P-ON+3.3V
Q3821
1
12
TO SYSTEM CONTROL
BLOCK DIAGRAM
HP-DET
LCD-P-ON
COMP-DET
2
Q3822
DIGITAL MAIN CBA UNIT
123
131415
JK3713
PC-RGB
-IN
6
7
DIF-OUT2
DIF-OUT1
(TUNER UNIT)
TU3001
12
5
IF-AGC
JK3701
COMPONENT
-Y/VIDEO-IN
COMPONENT
-Pb-IN
JK3706
COMPONENT
-Pr-IN
AUDIO(L)-IN
Q3709
AUDIO(R)-IN
BUFFER
DIGITAL
AUDIO-OUT
(COAXIAL)
JK3801
HEADPHONE
JACK
DRIVE
IC3803 (AUDIO AMP)
25
POWER
LIMIT
PWM
LOGIC
DRIVE
23
CN3801
POWER
DRIVE
18
2
1
SP(L)-
SP(L)+
SP3801
SPEAKER
L-CH
LIMIT
PWM
LOGIC
4
SP(R)+
DRIVE
20
3
SP(R)-
CONTROL LOGIC
SP3802
SPEAKER
R-CH
9-2
PL13.11ABLVA
3. Digital Signal Process Block Diagram
LCD PANEL
ASSEMBLY
LVDS-OD0(-)
LVDS-OD0(+)
LVDS-OD1(-)
LVDS-OD1(+)
LVDS-OD2(-)
LVDS-OD2(+)
LVDS-OCLK(-)
LVDS-OCLK(+)
LVDS-OD3(-)
LVDS-OD3(+)
19
17
161413
J3
J1
J2
K4
H2
H3
H4
AUDIO SIGNAL
VIDEO SIGNAL
2423222120
CN3906
L4
L3
K3
IC3401
DATA(0-15)
ADDESS(0-14)
(DDR3 SDRAM)
MMDQ(0-31)
DATA(16-31)
IC3402
(DDR3 SDRAM)
MMA(0-14)
IC3102
ADDESS(0-14)
(NAND FLASH MEMORY)
DATA(0-7)
DIGITAL MAIN CBA UNIT
MMCDAT(0-7)
VGA-HSYNC
IC3101 (DIGITAL SIGNAL PROCESS)
Y11
VGA-VSYNC
AA12
AB13
AD13
A/D
LVD S
TX
DIGITAL
SIGNAL
PROCESS
HDMI
I/F
HDMI SW
T7
W6
W23
W22
V23
V22
U23
V24
Y25
Y24
AA5
VIDEO
V7
DECODER
AB24
AA24
R9
AC24
AD25
AE3
Y23
AA23
AB25
AC25
AB17
AUDIO I/F
AE14
AC18
AC14
AC17
AD17
CONVERTER
DEMODULATOR
/MPEG DECODER
SW
IF-AGC
AB10
AB11
AD11
AD9
AE9
AA13
AC13
AC11
F4
ARC-OUT
F5
AE22
AC23
AUDI O
DECODER
AE23
AD23
AD24
AE24
AD22
AC22
DIF-OUT1
DIF-OUT2
VGA-R-IN
VGA-HSYNC
VGA-VSYNC
VGA-G-IN
VGA-B-IN
COM-VIDEO-Y/VIDEO-IN
COM-VIDEO-Pb-IN
IF-AGC
COM-VIDEO-Pr-IN
TO VIDEO/AUDIO
BLOCK DIAGRAM
AMP(L)-OUT
AMP(R)-OUT
AUDIO(L)-IN
AUDIO(R)-IN
HP(L)
HP(R)
SPDIF
JK3717
DATA0(+)
ARC
DATA0(-)
71494613
DATA1(+)
DATA1(-)
DATA2(+)
9-3
DATA2(-)
CLOCK(+)
101216
HDMI-IN1
HDMI-DATA
HDMI-CLOCK
CLOCK(-)
15
DATA0(+)
DATA0(-)
79461
JK3715
DATA1(+)
DATA1(-)
DATA2(+)
DATA2(-)
HDMI-IN2
CLOCK(+)
CLOCK(-)
3
101216
HDMI-DATA
HDMI-CLOCK
15
DATA0(+)
DATA0(-)
79461
JK3716
DATA1(+)
DATA1(-)
DATA2(+)
DATA2(-)
CLOCK(+)
CLOCK(-)
3
101216
HDMI-IN3
PL13.11ABLD
HDMI-DATA
HDMI-CLOCK
15
4. LED Backlight Drive Block Diagram
LCD PANEL
ASSEMBLY
VLED11
ILED13
ILED24
ILED35
ILED47
ILED58
CN1001
DRIVE
DRIVE 32DRIVE 5
ILED69
VLED211
DRIVE
DRIVE 32DRIVE 5
P-ON+21V
OVP
IC1001
(LED BACKLIGHT DRIVER)
10
16
Q1001
CONTROL
142413
BACKLIGHT-SW
LOGIC
1
BACKLIGHT-ADJ
PROTECT3
OVP
IC1002
(LED BACKLIGHT DRIVER)
10
16
Q1002
CONTROL
142413
LOGIC
1
POWER SUPPLY CBA
TO
SYSTEM CONTROL
BLOCK DIAGRAM
9-4
PL13.11BLBD
5. Power Supply Block Diagram
AL+3.3V
P-ON+21V
AMP+13V
DIGITAL MAIN CBA UNIT
8
CN3601
20-23
15-18
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
P-ON+21V20-23
AL+3.3V8
AMP+13V15-18
CN501
P-ON+21V
TO
SYSTEM CONTROL
RESET
P-ON-H2
BLOCKDIAGRAM
POWER SUPPLY CBA
For continued protection against risk of fire,
replace only with same type 2.5A, 250V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
2.5A 250V
T601
D601- D604
L602
L601
7
6
BRIDGE
RECTIFIER
LINE
FILTER
LINE
FILTER
8
5
+3.3V REG.
RESET
Q650
9
11
10
4
2
Q656, Q658
Q653
12
1
2
1
IC602
ERROR
VOLTAGE DET
4
3
HOT COLD
OVER
VOLTAGE
PROTECT
Q621
CONTROL
Q602
SWITCHING
F602
2.5A/250V
AC601
CN601
AC CORD
B
W
HOT CIRCUIT. BE CAREFUL.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F602) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
2.5A 250V
9-5
SWITCHING
Q601
PL13.11ABLP
[TYPE B]
1. System Control Block Diagram
P-ON+5V
LIGHT
SENSOR
IC4051
KEY SWITCH
D4051
POWER
FUNCTION CBA UNIT
SENSOR
REMOTE
RS4051
TO
POWER SUPPLY
BLOCK DIAGRAM
RESET
P-ON-H2
TO
LED BACKLIGHT DRIVE
BLOCK DIAGRAM
PROTECT3
BACKLIGHT-SW
BACKLIGHT-ADJ
POWER SUPPLY CBA
IC3005
(MAIN MICRO CONTROLLER)
6
LIGHT73
KEY-IN1
REMOTE
LED1
6
445 5
CN3101 CN4052
BUFFER
Q3010
LED DRIVE
Q3501, Q3502
A15
A13
D14
C14
LED1
LIGHT
KEY-IN1
REMOTE
USBDP
USBDN
T10
R10
COMP-DET
HP-MUTE
AUDIO-MUTE
C1
N12
G13
TU3901 (TUNER UNIT)
HP-DET
K16
SCL
4
R12
SCL
SDA
3
T12
SDA
AL+3.3V
Q3006
B16
P-ON-H2
SCK
SIN
T11
P11
Q3005
SOUT
R11
CS
P12
CN501
P-ON-H2
18 6
CN3701
4
RESET
20
IC3009
RESET
RESET J15
357
CN501
PROTECT3
211917
CN3701
B13
PROTECT3
BACKLIGHT-SW
BACKLIGHT-SW E2
XIN25
H15
BACKLIGHT-ADJ
F3BACKLIGHT-ADJ
XOUT25
H16
TO
VIDEO/AUDIO
BLOCK DIAGRAM
BACKLIGHT-SW
DIGITAL MAIN CBA UNIT
USBDP
USBDN
CN3009
USB JACK
COMP-DET
HP-MUTE
AUDIO-MUTE
TO VIDEO/AUDIO
BLOCK DIAGRAM
HP-DET
9-6
25MHz
OSC
X3001
652
1
SI
CS
SO
SCK
IC3006 (MEMORY)
PL13.11BBLS
2. Video/Audio Block Diagram
AUDIO SIGNAL
TO DIGITAL
SIGNAL PROCESS
BLOCK DIAGRAM
TO SYSTEM CONTROL
BLOCK DIAGRAM
VIDEO SIGNAL
DIGITAL MAIN CBA UNIT
VGA-R-IN
VGA-G-IN
VGA-B-IN
VGA-VSYNC
VGA-HSYNC
VGA-SCL
VGA-SDA
IF-AGC
DIF-OUT1
DIF-OUT2
6
7
DIF-OUT2
DIF-OUT1
(TUNER UNIT)
TU3901
COM-VIDEO-Pb-IN
COM-VIDEO-Y/VIDEO-IN
5
IF-AGC
COM-VIDEO-Pr-IN
AUDIO(L)-IN
AUDIO(R)-IN
SPDIF
3
5
6dB
6dB
(HEADPHONE AMP)
IC3851
1
7
Q3861
2
MUTE
AMP(L)-OUT
3
PWM
DRIVE
IC3801 (AUDIO AMP)
25,26
LOGIC
22,23
HP-DET
AMP(R)-OUT
12
PWM
LOGIC
DRIVE
20,21
17,18
HP-MUTE
COMP-DET
AUDIO-MUTE
BACKLIGHT-SW
Q3802
Q3801
P-ON+5V
Q3803
1
2
CONTROL LOGIC
BUFFER
-IN
BUFFER GATE
IC3014
Q3301
BUFFER
Q3302
12
123
BUFFER GATE
IC3013
131415
JK3001
PC-RGB
JK3702
COMPONENT
-Y/VIDEO-IN
COMPONENT
-Pb-IN
JK3701
COMPONENT
-Pr-IN
AUDIO(L)-IN
9-7
Q3701
AUDIO(R)-IN
BUFFER
DIGITAL
AUDIO-OUT
(COAXIAL)
JK3703
HEADPHONE
JACK
1
CN3801
SP(L)+
SP3801
SP(L)-
SP(R)-
SPEAKER
L-CH
432
SP(R)+
SP3802
SPEAKER
PL13.11BBLVA
R-CH
3. Digital Signal Process Block Diagram
LCD PANEL
ASSEMBLY
RXO0(-)
RXO0(+)
RXO1(-)
RXO1(+)
RXO2(-)
RXO2(+)
RXOCLK(-)
RXOCLK(+)
RXO3(-)
P15
R16
LVD S T X
19
R15
R14
RXO3(+)
171614
13
T16
T14
T15
AUDIO SIGNAL
VIDEO SIGNAL
2423222120
CN3013
N15
N16
P16
IC3002
(DDR2 SDRAM)
B1,B9,C2,C8,
D1,D3,D7,D9,
N4,N7,N8,P3,P4,
DATA(0-15)
ADDRESS(0-12)
H1,H3,H7,H9
F1,F9,G2,G8,
M2,M3,M7,M8,
N2,N3,N7,N8,
P2,P3,P7,P8,R2
P6-P8,R3,R4,R6,
R8,T2-T5
H1,H2,J1,J2,J4,K1,
K3,L1,L2,M1-M3,N1
DIGITAL MAIN CBA UNIT
HSYNC
IC3005 (DIGITAL SIGNAL PROCESS)
A14
VGA-HSYNC
VSYNC
B14
C11
VGA-R-IN
VGA-VSYNC
A/D
CONVERTER
SW
A9
C7
D8
C9
B11
COM-VIDEO-Pr-IN
COM-VIDEO-Pb-IN
COM-VIDEO-Y/VIDEO-IN
VGA-G-IN
VGA-B-IN
C10
TO
VIDEO/AUDIO
BLOCK DIAGRAM
DEMODULATOR
/MPEG DECODER
IF-AGC
A12
A16
B12
DIF-OUT1
DIF-OUT2
IF-AGC
B8
A8
AUDIO(R)-IN
AUDIO(L)-IN
AUDIO I/F
N10
SPDIF
B7
(R)-OUT
(L)-OUT
AMP
AMP
DIGITAL
SIGNAL
PROCESS
HDMI
AUDI O
DECODER
A7
IC3018 (HDMI SW)
414544484739383637
TMDS-D0(+)
TMDS-D0(-)
TMDS-D1(+)
7 42
94613
HDMI-IN1
JK3004
I/F
B4A4B3A3B2A2B1
26272324202117
TMDS-CLOCK(+)
TMDS-CLOCK(-)
TMDS-D1(-)
TMDS-D2(+)
TMDS-D2(-)
HDMI-DATA
101216
A1
18
HDMI-CLOCK
15
VIDEO
DECODER
79461
HDMI-IN3
JK3003
TMDS-D0(-)
TMDS-D0(+)
TMDS-D1(+)
575660596362545351
HDMI
SW
8
7
111014
TMDS-D0(+)
TMDS-D0(-)
TMDS-D1(+)
79461
JK3002
HDMI-IN2
3
TMDS-D1(-)
TMDS-D2(-)
TMDS-D2(+)
13
TMDS-D1(-)
TMDS-D2(+)
TMDS-D2(-)
3
101216
15
HDMI-DATA
HDMI-CLOCK
TMDS-CLOCK(-)
TMDS-CLOCK(+)
52
541
2
TMDS-CLOCK(+)
TMDS-CLOCK(-)
HDMI-DATA
HDMI-CLOCK
101216
15
IC3011
(HDMI SERIAL EEPROM)
15
SCL2
SCL1
2
HDMI-SCL
G14
7
14
SCL0
SDA2
SDA1
SCL3
3
10
HDMI-SDA
F14
6
SDA0
SDA3
11
VGA-SDA
VGA-SCL
TO
VIDEO/AUDIO
BLOCK DIAGRAM
9-8
PL13.11BBLD
4. LED Backlight Drive Block Diagram
LCD PANEL
ASSEMBLY
VLED11
ILED13
ILED24
ILED35
ILED47
ILED58
CN1001
DRIVE
DRIVE 32DRIVE 5
ILED69
VLED211
DRIVE
DRIVE 32DRIVE 5
P-ON+21V
OVP
IC1001
(LED BACKLIGHT DRIVER)
10
16
Q1001
CONTROL
142413
BACKLIGHT-SW
LOGIC
1
BACKLIGHT-ADJ
PROTECT3
OVP
IC1002
(LED BACKLIGHT DRIVER)
10
16
Q1002
CONTROL
142413
LOGIC
1
POWER SUPPLY CBA
TO
SYSTEM CONTROL
BLOCK DIAGRAM
9-9
PL13.11BLBD
5. Power Supply Block Diagram
AL+3.3V
P-ON+21V
AMP+13V
DIGITAL MAIN CBA UNIT
16
1-4
6-9
CN3701
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
P-ON+21V20-23
AL+3.3V8
AMP+13V15-18
CN501
P-ON+21V
TO
SYSTEM CONTROL
RESET
P-ON-H2
BLOCKDIAGRAM
POWER SUPPLY CBA
For continued protection against risk of fire,
replace only with same type 2.5A, 250V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
8
2.5A 250V
7
T601
6
BRIDGE
RECTIFIER
D601- D604
LINE
FILTER
L602
LINE
FILTER
L601
+3.3V REG.
IC651
RESET
Q650
Q653
9
10
5
4
2
12
11
1
2
1
IC602
ERROR
VOLTAGE DET
4
3
HOT COLD
OVER
VOLTAGE
PROTECT
Q621
CONTROL
Q602
SWITCHING
F602
2.5A/250V
AC601
CN601
AC CORD
B
W
HOT CIRCUIT. BE CAREFUL.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F602) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
2.5A 250V
9-10
SWITCHING
Q601
PL13.11BBLP
[TYPE C]
1. System Control Block Diagram
P-ON+5V
LIGHT
SENSOR
IC4051
KEY SWITCH
D4051
POWER
FUNCTION CBA UNIT
SENSOR
REMOTE
RS4051
6
TO
POWER SUPPLY
P-ON-H2
CN501
P-ON-H2
18 6
CN3602
BLOCK DIAGRAM
RESET
RESET
20 4
TO
LED BACKLIGHT DRIVE
BACKLIGHT-SW
BACKLIGHT-ADJ
CN501
BACKLIGHT-SW
BACKLIGHT-ADJ
19 5
17 7
CN3602
BLOCK DIAGRAM
PROTECT3
POWER SUPPLY CBA
PROTECT3
21 3
IC3001
(MAIN MICRO CONTROLLER)
LIGHT73
KEY-IN1
REMOTE
LED1
6
445 5
CN3101 CN4052
BUFFER
Q3010
Q3501, Q3502
LED DRIVE
215
210
205
208
LED1
LIGHT
KEY-IN1
REMOTE
USB(+)
USB(-)
194
195
(MEMORY)
IC3006
SCL
SDA
6
5
199
200
SPI-SCL
SPI-SDA
VGA-SCL
212
AMP-MUTE
VGA-SDA
127
213
Q3605
AL+3.3V
COMP-DET
133
Q3606
206
P-ON-H2
RESET
IC3009,
Q3104
216
STB-RESET
TU-SCL
TU-SDA
126
125
4
3
SCL
SDA
75
BACKLIGHT-SW
P-ON+3.3V
129
BACKLIGHT-ADJ
X3101
Q3103
XOUT
XIN
67
66
24MHz
OSC
134
PROTECT3
DIGITAL MAIN CBA UNIT
USB(+)
USB(-)
CN3009
USB JACK
VGA-SCL
9-11
AMP-MUTE
VGA-SDA
TO VIDEO/AUDIO
BLOCK DIAGRAM
TU3901 (TUNER UNIT)
COMP-DET
PL13.11CBLS
2. Video/Audio Block Diagram
AUDIO SIGNAL
VIDEO SIGNAL
VGA-R-IN
VGA-G-IN
VGA-B-IN
VGA-VSYNC
VGA-HSYNC
IF-AGC
DIF-OUT1
DIF-OUT2
COM-VIDEO-Pr-IN
COM-VIDEO-Pb-IN
COM-VIDEO-Y/VIDEO-IN
TO DIGITAL
SIGNAL PROCESS
BLOCK DIAGRAM
AUDIO(L)-IN
AUDIO(R)-IN
SPDIF
HP(R)
HP(L)
AMP(L)-OUT
3
VGA-SCL
VGA-SDA
AMP(R)-OUT
1
12
TO SYSTEM CONTROL
BLOCK DIAGRAM
AMP-MUTE
COMP-DET
2
Q3801
DIGITAL MAIN CBA UNIT
123
131415
JK3001
PC-RGB
-IN
6
7
DIF-OUT2
DIF-OUT1
(TUNER UNIT)
TU3901
12
5
IF-AGC
JK3702
COMPONENT
-Y/VIDEO-IN
COMPONENT
-Pb-IN
JK3701
COMPONENT
-Pr-IN
AUDIO(L)-IN
Q3701
AUDIO(R)-IN
BUFFER
DIGITAL
AUDIO-OUT
(COAXIAL)
JK3703
HEADPHONE
JACK
DRIVE
IC3801 (AUDIO AMP)
25
POWER
LIMIT
PWM
LOGIC
DRIVE
23
CN3801
POWER
DRIVE
18
2
1
SP(L)-
SP(L)+
SP3801
SPEAKER
L-CH
LIMIT
PWM
LOGIC
4
SP(R)+
DRIVE
20
3
SP(R)-
CONTROL LOGIC
SP3802
SPEAKER
R-CH
9-12
PL13.11CBLVA
3. Digital Signal Process Block Diagram
LCD PANEL
ASSEMBLY
LVDS-OD0(-)
LVDS-OD0(+)
LVDS-OD1(-)
LVDS-OD1(+)
LVDS-OD2(-)
LVDS-OD2(+)
LVDS-OCLK(-)
LVDS-OCLK(+)
LVDS-OD3(-)
LVDS-OD3(+)
LVDS-ED0(-)
LVDS-ED0(+)
LVDS-ED1(-)
LVDS-ED1(+)
LVDS-ED2(-)
LVDS-ED2(+)
LVDS-ECLK(-)
LVDS-ECLK(+)
LVDS-ED3(-)
LVDS-ED3(+)
32
CN3013
AUDIO SIGNAL
2423222120
19
1716403938373635302933
14
13
DATA(0-15)
ADDESS(0-13)
IC3002
(DDR2 SDRAM)
VIDEO SIGNAL
VGA-HSYNC
IC3001 (DIGITAL SIGNAL PROCESS)
26
108
105
103
106
107
A/D
CONVERTER
SW
VGA-VSYNC
32312927363438
104
99
35
101
102
122
123
100
LVDS
TX
DEMODULATOR
/MPEG DECODER
IF-AGC
606147
717074
120
121
AUDIO I/F
118
119
486364
114
130
115
116
117
548
DIGITAL
SIGNAL
AUDIO
DECODER
7
PROCESS
11
10
326
MDQL(0-7),
MDQU(0-7)
MA(0-13)
HDMI
I/F
9
898892919594878693
HDMI SW
VIDEO
DECODER
96
161519182221141320
DIGITAL MAIN CBA UNIT
23
DIF-OUT1
DIF-OUT2
TO VIDEO/AUDIO
BLOCK DIAGRAM
IF-AGC
VGA-HSYNC
VGA-VSYNC
VGA-R-IN
COM-VIDEO-Y/VIDEO-IN
COM-VIDEO-Pb-IN
COM-VIDEO-Pr-IN
VGA-G-IN
VGA-B-IN
AMP(L)-OUT
AMP(R)-OUT
AUDIO(L)-IN
AUDIO(R)-IN
HP(L)
HP(R)
SPDIF
DATA0(+)
DATA0(-)
79461
JK3003
DATA1(+)
DATA1(-)
DATA2(+)
9-13
CLOCK(+)
CLOCK(-)
DATA2(-)
3
101216
HDMI-IN1
HDMI-DATA
HDMI-CLOCK
15
DATA0(+)
DATA0(-)
79461
JK3002
DATA1(+)
DATA1(-)
DATA2(+)
DATA2(-)
HDMI-IN2
CLOCK(+)
CLOCK(-)
3
101216
HDMI-DATA
HDMI-CLOCK
15
DATA0(+)
DATA0(-)
79461
JK3004
DATA1(+)
DATA1(-)
DATA2(+)
DATA2(-)
HDMI-IN3
CLOCK(+)
3
HDMI-DATA
HDMI-CLOCK
CLOCK(-)
101216
15
PL13.11CBLD
4. LED Backlight Drive Block Diagram
LCD PANEL
ASSEMBLY
VLED11
ILED13
ILED24
ILED35
ILED47
ILED58
CN1001
DRIVE
DRIVE 32DRIVE 5
ILED69
VLED211
DRIVE
DRIVE 32DRIVE 5
P-ON+21V
OVP
IC1001
(LED BACKLIGHT DRIVER)
10
16
Q1001
CONTROL
142413
BACKLIGHT-SW
LOGIC
1
BACKLIGHT-ADJ
PROTECT3
OVP
IC1002
(LED BACKLIGHT DRIVER)
10
16
Q1002
CONTROL
142413
LOGIC
1
POWER SUPPLY CBA
TO
SYSTEM CONTROL
BLOCK DIAGRAM
9-14
PL13.11BLBD
5. Power Supply Block Diagram
AL+3.3V
P-ON+21V
AMP+13V
DIGITAL MAIN CBA UNIT
8
CN3602
20-23
15-18
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
P-ON+21V20-23
AL+3.3V8
AMP+13V15-18
CN501
P-ON+21V
TO
SYSTEM CONTROL
RESET
P-ON-H2
BLOCKDIAGRAM
POWER SUPPLY CBA
For continued protection against risk of fire,
replace only with same type 2.5A, 250V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
8
2.5A 250V
7
T601
6
BRIDGE
RECTIFIER
D601- D604
LINE
FILTER
L602
LINE
FILTER
L601
+3.3V REG.
IC651, Q657
RESET
Q650
Q653
9
10
5
4
2
12
11
1
2
1
IC602
ERROR
VOLTAGE DET
4
3
HOT COLD
OVER
VOLTAGE
PROTECT
Q621
CONTROL
Q602
SWITCHING
F602
2.5A/250V
AC601
CN601
AC CORD
B
W
HOT CIRCUIT. BE CAREFUL.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F602) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
2.5A 250V
9-15
SWITCHING
Q601
PL13.11CBLP
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using
replacement components rated for higher voltage,
wattage, etc. Replacement parts that have these
special safety characteristics are identified in this
manual and its supplements; electrical components
having such features are identified by the mark “#” in
the schematic diagram and the parts list. Before
replacing any of these components, read the parts list
in this manual carefully. The use of substitute
replacement parts that do not have the same safety
characteristics as specified in the parts list may create
shock, fire, or other hazards.
Notes:
1. Do not use the part number shown on these
drawings for ordering. The correct part number is
shown in the parts list, and may be slightly
different or amended since these drawings were
prepared.
2. All resistance values are indicated in ohms
(K = 10
3. Resistor wattages are 1/4W or 1/6W unless
otherwise specified.
4. All capacitance values are indicated in μF
(P = 10
5. All voltages are DC voltages unless otherwise
specified.
6.
This schematic diagrams are masterized version
that should cover the entire PL13.11 chassis
models.
Thus some parts in detail illustrated on this
schematic diagrams may vary depend on the
model within the PL13.11 chassis.
Please refer to the parts lists for each models.
7. The Circuit Board layout illustrated on this service
manual is the latest version for this chassis at the
moment of making this service manual.
Depend on the mass production date of each
model, the actual layout of each Board may differ
slightly from this version.
3
, M = 106).
-6
μF).
10-1 PL13.11SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
2
3
1
5.0 5.0
Voltage
Indicates that the voltage
is not consistent here.
Power on mode
(Unit: Volt)
1-D3
Distinction Area
Line Number
(1 to 3 digits)
Examples:
1. "1-D3" means that line number "1" goes to the line number
"1" of the area "D3".
2. "1-B1" means that line number "1" goes to the line number
"1" of the area "B1".
: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
THE FOLLOWING PAGES:
1. CAUTION:
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F602) is blown, first check to see that all components in the power supply circuit are not
defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components
in the power supply circuit to fail.
3. Note:
1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.
4. Voltage indications on the schematics are as shown below:
Plug the TV power cord into a standard AC outlet.:
5. How to read converged lines
6. Test Point Information
The reference number of parts on Schematic Diagrams/CBA can be retrieved by
application search function.
3
AREA D3
2
1
ABCD
10-2 PL13.11SC
AREA B1
1-D3
1-B1
10-3
4
3
2
1
IC601
OPEN
OPENC603
L601
LINE FILTER
AC601
AC CORD
2.5A/250V
F602
D653A
OPEN
1ZB20BB
D654
C654
470/16V
4.7K
R663
OPEN
R664
C652
470/25V 1ZB30BB
D652
D650
SB3150BH
3.3K
R661
3.9K
R657
8.2K
R667
2.7K
R660
22K
R659
180
R654
47K
R668
10K
R669
OPEN
C635
2200P/1KV
C650
OPEN
D405
1
R651 D656
RS1BJTD
C656
4.7/50V
MM5Z11B
D657
100K
R652
C651
470/25V
C653
470/25V
180
R655
KTC3875S-Y-RTK/P
Q653
KTC3875S
-Y-RTK/P
Q650
B
CN601
W
P-ON-H26
16 AMP+13V
20 P-ON+21V
15 AMP+13V
21 P-ON+21V
2 PROTECT1
CN501
1 LED-CONT(NU)
8 AL+3.3V
3 PROTECT3
12 GND
4 RESET
7 BACKLIGHT-ADJ
5 BACKLIGHT-SW
0.22/310V
C604
1.2M/1/2W
R601
VARISTOR
SA601
JS601
OPEN
JS602
OPEN
0.22/310V
C614
BC604
BEAD
BC603
BEAD
1N5406BH
D601
1N5406BH
D603
1N5406BH
D602
1N5406BH
D604
1.2K
R608
120
R607
120
R606
1ZB36BB
D608
560K
R603
1500P
C610
MM5Z6V2B
D605
OPEN
D607
1200P
C607
560K
R604
680P
/2KV
C606
270
R613
560K
R614
1SS400
D610
2SC5344SY
Q602
0.033
C608
TFZVTR27B
D607A
G
D
S
TK10A50D
Q601
OPEN
D608A
CES520
D609A
D651A
OPEN
OPEN
D652A
19 GND
22 P-ON+21V
23 P-ON+21V
OPEN
C639
C655
470/16V
OPEN
D654A
OPEN
R665
OPEN
C638
OPEN
D406
C663
100/10V
10K
R677
D663
OPEN
D660
SL431A-AT
2.7K
R658
0.1
C660
OPENC617
OPEN
C633
JS605
OPEN
JS606
OPEN
JS603
JS604
3.9K
R612
0.068
C609
100
R609
KTC3875S
-Y-RTK/P
Q621
0
R622
560
R621
MM5Z30B
D623
1SS400
D621
4.7
C623
OPEN
C622
2200P/250V
C602
OPENC616
0.3/2W
R611
10K
R623
OPEN
C621
D653
SB3A0BH
D655A
OPEN
D655
SB3A0BH
OPEN
R693
4
3
2
1
IC602
TLP781F
OPEN
C666
D661
1SS400
D650A
OPEN
D651
SB3150BH
OPEN
R674
OPEN
R675
OPEN
R691
OPEN
R692
OPEN
Q659
11 GND
10 GND
13 GND
18 AMP+13V
17 AMP+13V
14 GND
9 GND
OPEN
D658
OPEN
C661
OPEN
C630
OPEN
C631
OPEN
C632
C662
22/50V
OPEN
C664
0
R653
220
/200V
C605
L602
LINE FILTER
2.5A250V
0
R666
Q657A
OPEN
BACKLIGHT-SW
BACKLIGHT-ADJ
PROTECT3
P-ON+21V
OPEN
R602
OPEN
R610
JS609
220
/200V
C611
1500P
/1KV
C612
100K
R619
OPEN
R605
RS1JJTD
D606
D659A
OPEN
D659
SB3150BH
C667
470/25V
OPEN
C636
33K
R694
C668
470/25V
33K
R656
OPEN
Q702
OPEN
R704
OPEN
R703
OPEN
Q701
OPEN
C701
OPEN
R702
OPEN
R701
123
IC651
AP1117E33G-13
OUTINGND
6
5
4
2
1
7
8
9
10
11
12
T601
POWER TRANS
BC601
WIRE
BC602
WIRE
2.2
R688
2.7
R689
3.3
R685
3.3
R686
Q657
2SA950-O
3.3
R687
4.7/2W
R679
4.7/2W
R678
4.7/2W
R676
3.9
R683
3.9
R684
3.3K
R662
270
R671
Q658
2SA950-O
D662
SL431A-AT
270
R672
0
R682
0.1
C665
OPEN
R673
270
R670
KTC3875S
-Y-RTK/P
Q656
100
R680
Q658A
OPEN
10K
R681
1.5
R690
4
3
1
2
0.4
14.2
19.6
20.7
HOT CIRCUIT. BE CAREFUL.
0.7
0
(SWITCHING)
A FBCDE G
0
HOT COLD
(RESET)
0
-2.7
3.4
0
3.4
3.3
3.2
3.4
0
0
0
0
0
292.0
4.4
(SWITCHING)
0
0.1
SWITCHING
CONTROL
0.4
POWER SUPPLY CBA
TO DIGITAL MAIN
CBA UNIT CN3601
or CN3602 or CN3701
OVER
VOLTAGE
PROTECT
0
0
3.2
3.3
0
0
0
12.1
21.1
0.4
4.4
0
19.6
2.5
CONTINUE
POWER 2
21.1
21.1
21.1
ERROR
VOLTAGE DET
12.1
12.1
12.1
0 3.3 12.1
(+3.3V REG.)
(+3.3V REG.)
0
(+3.3V REG.)
3.4
(SWITCHING)
11.4
3.9
12.1 3.4
11.4
3.9
2.5
3.311.2
10.6
(10.6)
PL13.11SCP1
Power Supply 1 Schematic Diagram
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F602) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
For continued protection against risk of fire,
replace only with same type 2.5A, 250V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
2.5A 250V
10-4
SK210TD
D1001
100K
R1030
0
R1028
OPEN
C1020
0.1
C1016
360
R1002
12K
R1027
1
2
3
4
5
6
7
9
10
8
11
12 13
14
24
23
21
18
19
22
17
20
15
16
RT
CONTROL
LOGIC
COMP
GND
NU
DRIVE
ISET
OVP
MCP
SEL
VIN
GND
LDO
DRIVE
DRIVE
DRIVE
DRIVE
DRIVE
DRIVE
DRIVE
IC1001
HA7209PC
1
C1043
220P/500V
C1026
4.7
C1041
OPEN
C1039
360
R1001
100
R1041
P-ON+21V
PROTECT3
BACKLIGHT-SW
BACKLIGHT-ADJ
5ILED3
CN1001
1VLED1
3ILED1
4ILED2
D1021
OPEN OPEN
C1031
D1022
OPEN OPEN
C1032
0
R1022
22uH
L1001
OPEN
R1050
OPEN
D1050
OPEN
R1052
1SS400
D1003
0.18/2W
R1018
1000P
C1022
200
R1012
OPEN
C1024
10
R1010
Q1001
AP18T10AGH-HFG
D
S
OPEN
D1005
OPEN
R1014
OPEN
R1015
10K
R1008
OPEN
C1033D1023
OPEN
0
R1021
0
R1023
2NU
330/25V
C10011C1003
OPEN
C1005
1
C1004
330/25V
C1002
100K
R1009
12K
R1032
1
2
3
4
5
6
7
9
10
8
11
12
13
14
24
23
21
18
19
22
17
20
15
16
RT
CONTROL
LOGIC
COMP
GND
NU
DRIVE
ISET
OVP
MCP
SEL
VIN
GND
LDO
DRIVE
DRIVE
DRIVE
DRIVE
DRIVE
DRIVE
DRIVE
IC1002
HA7209PC
OPEN
C1025
1
C1044
0
R1026
1000P
C1023
360
R1004
0
R1024
OPEN
R1051
0.18/2W
R1019
OPEN
R1053
220P/500V
C1027
100
R1042
10
R1011
22uH
L1002
360
R1003
100K
R1031
OPEN
R1016
D1024
OPEN
OPEN
R1017
Q1002
AP18T10AGH-HFG
D
S
4.7
C1042
200
R1013
OPEN
C1036
OPEN
D1006
0
R1033
OPEN
C1021
D1026
OPEN
D1025
OPEN
1SS400
D1004
OPEN
C1040
1000P
C1038
0
R1025
OPEN
C1034
SK210TD
D1002
OPEN
D1051
OPEN
C1035
0.1
C1017
1KR1005
10KR1006
100K
R1007
1
C1006
1000P
C1037
0
R1029
6NU
7ILED4
8ILED5
9ILED6
10NU
11VLED2
0
R1040
0
R1047
1
C1007
47/100V
C1008
1/100V
C1018
OPEN
C1012
47/100V
C1010
1/100V
C1014
510K
R1034
430K
R1035
27K
R1036
1/100V
C1019
47/100V
C1011
47/100V
C1009
1/100V
C1015
OPEN
C1013
510K
R1037
430K
R1038
27K
R1039
POWER SUPPLY CBA
1
2
3
4
HLKJIM
4.9
3.3
1.6
0
17.8
0
4.9
2.9
0
0.1
2.9
0
0.6
0.5
1.0
1.3
1.4
0
2.9
0
0
0
0.8
LED BACKLIGHT
DRIVER
CONTINUE
POWER 1
TO LCD PANEL
ASSEMBLY
0.1
20.8
(SWITCHING)2.8
0
0.1
3.0
2.9
1.3
5.1
0.6
0
1.4
18.2
0
5.1
0
0
0
3.3
0 2.9
2.9
1.0
0
0.1
LED BACKLIGHT
DRIVER
0.5
1.5
0.6
(SWITCHING)
20.8
49.8
0.5
0.6
0.9
0.5
0.7
0.6
49.2
PL13.11SCP2
Power Supply 2 Schematic Diagram
10-5
2 P-ON+5V
OPEN
C4055
6 KEY-IN1
D4002
OPEN
18K
R4001
0.1
C4053
CN4052
1 AL+3.3V
SW4004
0.1
C4057
SW4005
10
C4051
R4055
OPEN
SW4006
3 LIGHT
R4059
OPEN
7 GND
5 REMOTE
4.7K
R4003
SW4003
R4058
10K
D4051
SMLE12WBC7W1HR
2.2K
R4005
8.2K
R4002
SW4002
R4056
10K
1000P
C4052
1
2
34
5
6
IC4051
PH5502B2NA1-E4
OUT
GND
VCC NU
NU
NU
2.7K
R4004
SW4001
R4052
6.8K
2.2K
R4006
D4001
MM5Z5V6B
231
RS4051
RS-272
VOUT
GND
VCC
0.1
C4054
9 SDA(NU)
0.1
C4002
1K
R4054
10
C4056
R4060
OPEN
R4057
27K
SW4007
4.7K
R4053
4 LED1
8 SCL(NU)
R4051
56
7 GND
6 KEY-IN1
5 REMOTE
9 SDA(NU)
4 LED1
8 SCL(NU)
2 P-ON+5V
CN4053
1 AL+3.3V
3 LIGHT
1
2
CAB
FUNCTION CBA UNIT
UNLESS OTHERWISE SPECIFIED:
SWITCHES ARE SKRMABE010.
VOL
UP
(REMOTE SENSOR)
VOL
DOWN
TO DIGITAL MAIN
CBA UNIT CN3101
or CN3105
CH UP
POWER
SOURCE POWERMENU
CH
DOWN
(NO CONNECTION)
(LIGHT SENSOR)
PL13.11SCF
Function Schematic Diagram
10-6
OPENR3882
6TP
3PC3905
OPENR3881
7 GND
3 OE1
7GND
25 P-ON+3.3V
6GND
29PANEL-SDA
28 GND
30GND
12 LVDS-OD3(+)
M4
M7
OPENR3880
22LVDS-OCLK(+)
L6
OPENR3928
OPENR3884
J3
5 POL
27 VCOM
28PANEL-SCL
18 LVDS-OD2(+)
H4
2 OE2
27 VCOM
21 LVDS-OD1(-)
3PC3912
29 LCD+21V
LCD-P-ON
26 PWR-CTRL
16 LVDS-OCLK(-)
M6
OPENC3914
J1
16 LVDS-OCLK(-)
16LVDS-OD1(+)
9 LVDS-OD5(-)
15 LVDS-OCLK(+)
OPENR3975
18LVDS-OD2(-)
2 OE2
F1
29 LCD+21V
OPENC3941
14 GND
R5OE2
K6
P1NU
OPENR3974
23GND
G3
22 LVDS-OD0(+)
1 STV
24LVDS-OD3(-)
H2L5
5 POL
25LVDS-OD3(+)
L4
1 STV
24 GND
3PC3906
20 LVDS-OD1(+)
10 LVDS-OD4(+)
17 GND
3PC3913
19 LVDS-OD2(-)
20GND
21 LVDS-OD1(-)
2LCD+12V
R6TP
OPENR3977
J5
OPENC3938
3PC3908
N5
OPENR3976
J7 NU
22 LVDS-OD0(+)
P4STV
CN3903
31 LCD+21V
30 LCD+21V
3PC3911
11GND
26GND
N3OE
23 LVDS-OD0(-)
13LVDS-OD0(+)
7 GND
M5 11 LVDS-OD4(-)
13 LVDS-OD3(-)
21LVDS-OCLK(-)
3OE
OPENC3940
11 LVDS-OD4(-)
K7 NU 8 LVDS-OD5(+)
28 GND
OPENR3883
3PC3903
19LVDS-OD2(+)
19 LVDS-OD2(-)
15 LVDS-OCLK(+)
17GND
L7
23 LVDS-OD0(-)
14GND
12 LVDS-OD3(+)
10NU
4LCD+12V
3PC3916
9LVDS-SEL
20 LVDS-OD1(+)
26 PWR-CTRL
CN3905
1LCD+12V
12LVDS-OD0(-)
3PC3904
6TP
P3CPV
3PC3907
9 LVDS-OD5(-)
K5
OPENC3998
17 GND
27BIST
N2 NU
OPENC3942
10 LVDS-OD4(+)
4 CPV
15LVDS-OD1(-)
OPENC3939
OPENC3915
R3POL
F3
L3
*1
IC3101(1/7)
MN2WS0270EA
K3
4 CPV
F2
CN3904
30 LCD+21V
OPENR3978
24 GND
3LCD+12V
13 LVDS-OD3(-)
VCOM-PWM
14 GND
P2 NU
18 LVDS-OD2(+)
25 P-ON+3.3V
8PANEL-WP
J6
H3
8 LVDS-OD5(+)
OPENR3979
5GND
9LVDS-OCLK(+)
23PANEL-WP
10LVDS-OCLK(-)
2PANEL-SDA
18LVDS-OD0(+)
3PANEL-SCL
5GND
1GND
17GND
26GND
19LVDS-OD0(-)
14GND
21NU
7LVDS-OD3(-)
16LVDS-OD1(-)
8GND
13LVDS-OD2(-)
22LVDS-SEL
15LVDS-OD1(+)
4NU
CN3901
30LCD+12V
24GND
6LVDS-OD3(+)
29LCD+12V
28LCD+12V
25GND
20GND
12LVDS-OD2(+)
27LCD+12V
11GND
LCD+12V/+21V
R3915 OPEN
LVDS-ED4(+)
LVDS-OD4(+)
LVDS-ED3(+)
LVDS-OD3(-)
LVDS-ED0(-)
LVDS-OD3(+)
LVDS-OD0(+)
LVDS-OCLK(-)
LVDS-OD1(+)
LVDS-ED1(+)
LVDS-ED2(-)
LVDS-ED0(+)
LVDS-ECLK(+)
LVDS-OCLK(+)
LVDS-ED3(-)
LVDS-OD2(+)
LVDS-ED1(-)
LVDS-OD0(-)
LVDS-OD1(-)
LVDS-ED2(+)
LVDS-ED4(-)
LVDS-OD2(-)
LVDS-ECLK(-)
LVDS-OD4(-)
OPENC3927
3PC3925
3PC3919
OPENC3926
3PC3921
3PC3924
3PC3920
3PC3923
3PC3922
R3914 OPEN
J2
R3913 OPEN
K4
3PC3918
3PC3917
3PC3928
P-ON+21V
OPEN
R3909
OPEN
R3910
OPEN
R3908
OPEN
R3907
PANEL-WP
PANEL-SCL
PANEL-SDA
3 PANEL-SCL
4 PANEL-SDA
CN3902
1 GND
2 PANEL-WP
VCOM-DC
11K
R3931
Q3901
2SC4081UBTLQ
OPEN
R3924
1K
R3935
12K
R3932
3.9K
R3934
12K
R3933
47/25V
C3947
0.1
C3948
P-ON+3.3V
OPENR3904
OPENR3906
OPEN
R3925
BACKLIGHT-ADJ
P7 BACKLIGHT-ADJ
10K
R3901
VCOM-PWM
10K
R3916
3
(NO CONNECTION)
FE
4
C
(NO CONNECTION)
TO DIGITAL
MAIN 6
IC3101(5/7)
1
LVDS
TX
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
CONTINUE
DIGITAL 2
DIGITAL MAIN CBA UNIT
AB D
2
(NO CONNECTION)
CONTINUE
DIGITAL 2
CONTINUE
DIGITAL 2
CONTINUE
DIGITAL 7
CONTINUE
DIGITAL 4
CONTINUE
DIGITAL 7
(NO CONNECTION)
(NO CONNECTION)
(DRIVE)
Digital Main 1 Schematic Diagram [TYPE A]
PL13.11ASCD1
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-7
50LCD+21V
0R3867
OPEN
R3896
OPEN
C3902
6GND
49LCD+21V
OPEN
C3909
24LVDS-OD0(-)
46LCD-P-ON
0R3866
D3902
1SS400
31GND
9GND
2NU
12LVDS-OD4(-)
44P-ON+3.3V
11LVDS-OD4(+)
7GND
16LVDS-OCLK(+)
LCD-P-ON
OPEN
R3941
25GND
39LVDS-ED0(+)
CN3906
1NU
4NU
13LVDS-OD3(+)
19LVDS-OD2(+)
22LVDS-OD1(-)
37LVDS-ED1(+)
23LVDS-OD0(+)
8GND
100R3905
30LVDS-ED3(-)
PROTECT3
27LVDS-ED4(+)
28LVDS-ED4(-)
40LVDS-ED0(-)
OPEN
R3891
18GND
51GND
45VCOM
0R3900
OPEN
R3940
OPENR3903
0R3923
34GND
36LVDS-ED2(-)
21LVDS-OD1(+)
43P-ON+3.3V
OPEN
R3899
42GND
0R3926
OPEN
C3910
35LVDS-ED2(+)
0R3869
OPEN
C3996
3NU
29LVDS-ED3(+)
OPEN
R3897
26GND
14LVDS-OD3(-)
33LVDS-ECLK(-)
Q3905
OPEN
1
2
36
7
8
45
48LCD+21V
Q3904
OPEN
0
R3942
10GND
32LVDS-ECLK(+)
OPEN
C3997
38LVDS-ED1(-)
0R3922
47GND
20LVDS-OD2(-)
15GND
17LVDS-OCLK(-)
VCOM-PWM
0R3902
5NU
41GND
OPEN
R3898
1
2
3
45
6
7
8
IC3901
OPEN
SS
EN
COMP
FB GND
SW
IN
BST
OPEN
C3946
OPEN
C3951
OPEN
C3950
OPEN
R3936OPEN
C3955
OPEN
R3938
OPEN
R3939OPEN
R3937
LCD+12V/+21V
OPEN
C3949
OPEN
D3905
OPEN
R3952
D3906
OPEN
OPEN
C3943
OPEN
C3944
OPEN
C3945
L3901
OPEN
OPEN
C3958
OPEN
C3959
OPEN
C3956
OPEN
C3954
OPEN
R3911
OPEN
R3912 C3952
OPEN
D3901
OPEN OPEN
C3953
OPEN
R3550
P-ON-H2
OPEN
R3895
OPEN
C3992
OPEN
C3991
4.7
C3901
0R3982
VCOM-DC
P-ON+3.3V
LVDS-ED3(+)
LVDS-ED3(-)
LVDS-ECLK(-)
LVDS-ECLK(+)
LVDS-ED2(-)
LVDS-ED2(+)
LVDS-ED1(-)
LVDS-ED1(+)
LVDS-ED0(+)
LVDS-ED0(-)
LVDS-ED4(-)
LVDS-ED4(+)
OPENR3985
OPENR3984
0R3986
0R3987
R3919 0x4
LVDS-OD2(-)
LVDS-OD2(+)
LVDS-OD1(+)
LVDS-OD1(-)
LVDS-OD0(+)
LVDS-OD0(-)
LVDS-OCLK(-)
LVDS-OCLK(+)
R3920 0x4
OPENR3980
OPENR3981
0R3921
0R3943
LVDS-OD4(-)
LVDS-OD4(+)
LVDS-OD3(-)
LVDS-OD3(+)
0R3988
0R3989
OPENR3983
OPENR3917
OPENR3918
PANEL-SDA
PANEL-WP
PANEL-SCL
OPEN
R3990
P-ON+21V
CONTINUE
DIGITAL 1
DIGITAL MAIN CBA UNIT
H
3
4
J
1
2
LIKG
CONTINUE
DIGITAL 1
CONTINUE
DIGITAL 8
CONTINUE
DIGITAL 6
CONTINUE
DIGITAL 7
CONTINUE
DIGITAL 2
TO LCD PANEL
ASSEMBLY
Digital Main 2 Schematic Diagram [TYPE A]
PL13.11ASCD2
10-8
D17
C3
B2
C2
C1
A6
C5
F11
B4
B5
C9
D7
C8
B1
E6
56R3417
D16
A4
C6
C16
C7
B7
C4
D8
D19
B3
A3
A2
B14
C18
C17
B18
A14
B13
B17
C13
A17
D11
B12
D15
C15
A12
C11
B15
C14
C12
C19
B9
B10
F10
D12
E11
F14
56R3418
F12
G10
270R3421
270R3423
D4
F19
10K
R3419
L2 CS#
K1 ODT
F9VSSQ7
0.1
C3414
10
C3431
G3 DQSL#
F1VDDQ7
J2VSS5
10
C3411
D2VDDQ5
E9VDDQ6
B1VSSQ1
NU J9
C1VDDQ3
K9CKE
NU J1
R1VDD8
H9VDDQ9
B2VDD1
220
R3427
D1VSSQ3
G1VSSQ8
N9VDD7
L1NU
P9VSS10
K8VDD5
CK J7
270
R3425
M8VREFCA
K7CK#
M1VSS7
B7 DQSU#
R9VDD9
M9VSS8
D8VSSQ4
E8VSSQ6
A1VDDQ1
C9VDDQ4
G9VSSQ9
T9VSS12
D3 DMU
NU L9
A8VDDQ2
E1VSS3
J8VSS6
E7 DML
A9VSS1
K2VDD4
H2VDDQ8
E2VSSQ5
H1VREFDQ
C7 DQSU
B9VSSQ2
L3 WE#
K3 CAS#
P1VSS9
G7VDD3
0.1
C3413
G8VSS4
B3VSS2
J3 RAS#
T1VSS11
F3 DQSL
D9VDD2
N1VDD6
DQL3F8
DQU5A2
DQU0D7
DQU3C2
DQL0E3
DQL5H8
DQU7A3
DQL4H3
DQL7H7
DQU4A7
DQL2F2
DQU6B8
DQU1C3
DQU2C8
DQL6G2
DQL1F7
240
R3428
L8 ZQ
B1VSSQ1
J2VSS5
DQU7A3
DQL1F7
DQL3F8
G7VDD3
D9VDD2
P1VSS9
B7 DQSU#
DQL2F2
D3 DMU
A9VSS1
M8VREFCA
DQL0E3
E1VSS3
0.1
C3422
H1VREFDQ
R1VDD8
K3 CAS#
DQL5H8
DQL6G2
CK J7
C9VDDQ4
H2VDDQ8
E9VDDQ6
0.1
C3424
G3 DQSL#
240
R3432
T1VSS11
DQU4A7
220
R3431
M1VSS7
N9VDD7
C1VDDQ3
DQU3C2
T9VSS12
P9VSS10
B3VSS2
L2 CS#
DQU2C8
F9VSSQ7
D8VSSQ4
A8VDDQ2
E2VSSQ5
0.1
C3423
L3 WE#
DQL7H7
A1VDDQ1
D2VDDQ5
G8VSS4
K9CKE
C7 DQSU
B2VDD1
DQU0D7
G1VSSQ8
DQU1C3
NU J1
NU J9
10
C3420
K2VDD4
0.1
C3421
N1VDD6
F3 DQSL
M9VSS8
10
C3432
DQL4H3
K1 ODT
R9VDD9
K8VDD5
NU L9
L8 ZQ
K7CK#
F1VDDQ7
E8VSSQ6
E7 DML
DQU6B8
J8VSS6
270
R3429
H9VDDQ9
D1VSSQ3
J3 RAS#
L1NU
DQU5A2
B9VSSQ2
G9VSSQ9
T2 RESET# T2 RESET#
VCC+1.5V
0.1
C3418
0.1
C3417
0.1
C3426
0.1
C3425
0.1
C3419
0.1
C3429
270
R3426
270
R3430
0.1
C3428
0.1
C3430
BA2M3
BA0M2
BA1N8
BA0M2
BA1N8
BA2M3
A1P7
A5P2
A8T8
A3N2
A9R3
A10/APL7
A7R2
A13T3
A11R7
A14T7
A0N3
A12/BC#N7
A2P3
A6R8
A4P8
NU
IC3401
K4B1G1646G-BCH9
M7
A14T7
NU
IC3402
K4B1G1646G-BCH9
M7
A13T3
A1P7
A2P3
A0N3
A12/BC#N7
A8T8
A4P8
A7R2
A6R8
A9R3
A3N2
A5P2
A11R7
A10/APL7
56R3412
D3
IC3101(2/7)
*1
MN2WS0270EA
D6
270R3411
0.1C3409
270R3422
0.1C3410
270R3424
270R3410
0.1C3406
240R3420
1C3405
D1
G7
0.1
C3427
0.1
C3416
0.1
C3415
0.1
C34121C3408
56R3416
OPEN
C3407
G11
E8
G8
E7
E19
F18
E18
E17
D18
F17
F16
E16
D10
E10
D9
G9
G16
E15
D14
E14
R3409 56x4
R3405 56x4
R3406 56x4
R3407 56x4
R3408 56x4
56R3414
56R3413
56R3415
G12
10KR3433
AL+3.3VT5
OPEN
R3401
OPEN
C3401
OPEN
C3402
OPEN
R3402
OPEN
R3403
OPEN
C3403
OPEN
C3404
OPEN
R3404
MMXCK
MMDM2
MMDM1
MMDQ21
MMDQ10
MMDQ12
1
MMDQ30
MMXCS1
M
MMDQ15
P
MMDQ19
MMDQ28
MMDQ5
MMDQ27
MMDQS1
MMDQ26
MMDQ16
MMDQ20
Q
MMDQ8
MMVREF0
MMDQ25
MMXRAS
MMDQ14
3
N
MMDQ29
MMDQ9
MMCKE0
MMDM3
MMDM0
MMDQS3
MMDQ0
MMDQ23
MMDQ1
MMDQ22
MMDQ17
MMDQS2
R
MMCK
MMDQ3
MMDQ7
MMDQ4
MMXCS0
4
2
MMDQ13
MMDQ2
MMDQ6
O
MMDQ31
MMODT0
MMDQ11
MMDQ18
MMDQ24
MMDQ31
MMDQ30
MMDQ29
MMDQ28
MMDQ27
MMDQ26
MMDQ25
MMDQ24
MMDQ23
MMDQ22
MMDQ20
MMDQ19
MMDQ18
MMDQ17
MMDQ16
MMDQ15
MMDQ14
MMDQ13
MMDQ12
MMDQ11
MMDQ10
MMDQ9
MMDQ8
MMDQ7
MMDQ6
MMDQ5
MMDQ4
MMDQ3
MMDQ2
MMDQ1
MMDQ21
MMDQ0
MAIN MICRO CONTROLLER
/DIGITAL SIGNAL PROCESS
MEMORY
I/F
TO DIGITAL
MAIN 6
IC3101(5/7)
DIGITAL MAIN CBA UNIT
MMVREF1
MMXDQS1
MMDQS0
MMXDQS0
MMXDQS2
MMXDQS3
MMODT1
MMCKE1
MMZQ
MMXRESET
(DDR3 SDRAM)
MMDQ5
MMDQ13
MMDQ0
MMDQ14
MMDQ10
MMDQ6
MMDQ8
MMDQ12
MMDQ1
MMDQ15
MMDQ3
MMDQ11
MMDQ9
MMDQ4
MMDQ7
MMDQ2
MMDQ25
MMDQ29
MMDQ23
MMDQ21
MMDQ27
MMDQ24
MMDQ19
MMDQ22
MMDQ17
MMDQ18
MMDQ28
MMDQ30
MMDQ31
MMDQ16
MMDQ26
(DDR3 SDRAM)
MMDQ20
MMA0
MMA9
MMA12
MMA5
MMA1
MMA14
MMA6
MMA2
MMA10
MMA8
MMA7
MMA13
MMA4
MMA3
MMA11
MMA14
MMA6
MMA5
MMA1
MMA12
MMA2
MMA7
MMA4
MMA8
MMA10
MMA3
MMA11
MMA9
MMA13
MMA0
MMVREF2
DDR3VOUT
NU
MMA2
MMA2
MMA6
MMA6
MMA8
MMA8
MMA14
MMA14
MMA9
MMA9
MMA11
MMA11
MMA13
MMA13
MMA7
MMA7
MMA4
MMA4
MMA5
MMA5
MMA1
MMA1
MMA12
MMA12
MMBA1
MMA10
MMA10
MMA3
MMA3
MMA0
MMA0
MMBA2
MMBA0
MMXWE
MMXCAS
NU
CONTINUE
DIGITAL 7
DDRPWRON
Digital Main 3 Schematic Diagram [TYPE A]
PL13.11ASCD3
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-9
P22NU
M20 NU
VCOM-PWM
1KR3118
R3204 75
V20 NU
W17NU
T19NU
Y21 NU
X3101
25MHz
AE4 AXI
C25 NU
R3192
56x4
L20 NU
AB22 NU
F24 NU
W19 NU
E23 NU
Y22 NU
AD20NU
C3125
0.1
D24 NU
10KR3128
M21 NU
W18NU
G21 NU
AD19NU
AC20NU
10K
R3111
AA20NU
10KR3123
F23 NU
R3201 75
10K
R3113
B21MMCDAT4
AA21NU
R3202 75
J24NU
N21 NU
AD4 AXO
D20 NU
OPEN
R3169
U19 NU
AD8 NU
AL+3.3V
J25NU
R3191
56x4
J22NU
1KR3224
1
2
3
4
5
6
7
9
10
8
11
12
13
15
16
14
17
18
19
20
21
30
28
27
42
29
26
25
40
39
24
23
22
41
38
37
36
34
33
35
32
31
43
44
48
45
46
47
IC3102
K9F1G08U0D-SCB0
K20 NU
AB7 NU
R3190 75
J23 NU
A24XNFWE
OPEN
R3130
N19 NU
10KR3132
U9 NU
Y17NU
OPENR3127
AA19NU
P21NU
G4 NU
R22NU
4TRSTN
E21XNFRE
Y8 NU
J20 NU
H20 NU
OPENR3125
P-ON+5V
T20NU
OPENR3115
G24NU
L21 NU
R20NU
W21 NU
OPENR3122
5JTMS
7JTDI
T21NU
AB23 NU
R3205 22
U20 NU
H21 NU
E24 NU
AE20NU
AC5 NU
E20MMCDAT5
K19 NU
STB-RESET
F20NU
F22 NU
COMP-DET
AB20NU
AA17NU
L19 NU
W20 NU
AA18NU
P24NU
H23NU
AA22 NU
P25NU
10KR3173
V21 NU
C20MMCDAT7
N20 NU
K22NU
V19 NU
R21NU
AA7 NU
J19 NU
D21MMCDAT2
C23NFCLE
C3126
0.1
STMTIME1
B20MMCDAT6
10K
R3136
10KR3124
M19 NU
L2 HP-DET
B22
IC3101(3/7)
*1
MN2WS0270EA
MMCDAT0
AB18NU
M3 NU
F25 NU Y19NU
15P
C3124
K21 NU
U21 NU
G6 NU
H22NU
100
R3112
P6 VCOM-PWM
AB19NU
R3203 75
AC19NU
Y16NU
15P
C3128
6JTDO
A23XNFCE
D25 NU
B24XNFWP
10KR3121
CN3104
10GND
R19NU
OPEN
R3126
1AL+3.3V
10KR3198
3EVTRG
C22NU
2XRST
C21MMCDAT3
R3189 75
P-ON+3.3V
B23NFALE
H6 COMP-DET
G22NU
100
R3129
A22MMCDAT1
OPENR3116
OPEN
R3208
A20 NU
Y20NU
8EJTCK
D22NANDRYBY
P19 NU
270
R3170
P20 NU
Y18NU
G23NU
9NU
OPEN
R3210
H19 NU
W16NU
W15NU
HP-DET
OPEN
R3135
W
1
T
3
4
2
VSU X
(NO CONNECTION)
NU
MMCDAT0
MMCDAT4
R/B
NU
NU
I/O3
NU
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
VCC
NU
NU
NU
MMCDAT5
CLE
NU
NU
NU
MMCDAT2
NU
NU
WP
NU
MMCDAT2
DIGITAL MAIN CBA UNIT
NU
NU
VSS
I/O4
MMCDAT3
CONTINUE
DIGITAL 7
MMCDAT0
NU
(NAND FLASH MEMORY)
NU
CE
MMCDAT4
MEMORY
I/F
NU
MMCDAT7
MMCDAT6
WE
MMCDAT1
MMCDAT1
I/O2
VCC
I/O0
MMCDAT5
TO DIGITAL
MAIN 6
IC3104(5/7)
NU
I/O5
MMCDAT7
MMCDAT6
NU
NU
RE
NU
NU
I/O6
CONTINUE
DIGITAL 8
NU
I/O7
ALE
VSS
MMCDAT3
NU
NU
NU
NU
I/O1
NU
CONTINUE
DIGITAL 1
CONTINUE
DIGITAL 6
Digital Main 4 Schematic Diagram [TYPE A]
PL13.11ASCD4
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-10
C24 UART0TX
N24 USB0OD
N23 USB0VBUS
N22 USB0(-)
M24 USB0(+)
OPEN
D3001
OPEN
C3003
AB9NU
AE9
AD9
AA13IF-AGC
Y15TU-SCL
AA16TU-SDA
Y12NU
AA15NU
33R3006
33R3007
39P
C3013
L3003
3.3uH0.1
C3011
0.1
C3014 L3004
3.3uH
OPEN
C3010
OPEN
C3002
OPEN
D3002
C3739
1
L3706
OPEN
1
2
34
5
IC3701
AP2151WG-7
VOUT
GND
/FLAG EN
VIN
AB8 NU
K23 NU
K24 NU
P-ON+3.3V
4GND
CN3704
1USB+5V
3USB0(+)
2USB0(-)
TU3001
TUNER UNIT
1
+3.3V2GND3SDA4SCL5IF-AGC6DIF-OUT17DIF-OUT2
OPEN
D3010
270
R3005
270
R3003
OPEN
C3026
OPEN
C3027
OPEN
C3117
UARTOTX 2
100R3175
R3101
10K
UARTORX 3
E22 UARTOTX
R3108
OPEN
100R3176
P-ON+5V 1
CN3101
GND 4
OPEN
C3116
C3742
220/6.3V
R3761
10K
100
R3758
0.1
C3727
2.49KR3172
10kR3177
OPEN
C3115
AC9NU
W14NU
W10NU
MM5Z5V6B
D3007
OPEN
C3039
10
C3040
OPEN
C3041
L3005
2.2uH
4.7KR3011
4.7KR3025
P-ON+5V
10KR3001
0.1
C3009
10KR3004
Y13NU
W8NU
AA8NU
4GND
CN3701
1USB1(+)
CN3705
4USB+5V
3USB+5V
3USB1(-)
2USB1(+)
2USB1(-)
6GND
5GND
1GND
L3701
OPEN
L23 USB1(+)
M22 USB1(-)
M25 USB1VBUS
C3716
OPEN12
34
5
IC3702
OPEN
VOUT
GND
/FLAG EN
VIN
OPEN
R3702
R3704
OPEN
C3715
OPEN
OPEN
C3714
0
R3734
0
R3736
R3735
OPEN
UART1RX
UART1TX
100R3194
G20 UART1TX
1KR3217
100R3193
F21 UART1RX
M1
IC3101(4/7)
*1
MN2WS0270EA
NU
N4 NU
M2 NU
P5 NU
B25 NU
D23 NU
R6 RX(-)
R2 TCT
C3701
0.01
R1 TX(+)
CN3706
R8 GND
C3744
0.01
R3 TX(-)
R5 RCT
R7 NU
R4 RX(+)
AC8RX(-)
AC7RX(+)
AE6TX(-)
AD6TX(+)
U10NU
AC6CTRL11 CTRL11
C3129
1
0.1
C3008
10KR3180
M23 USB10D
ZAC
1
4
2
ABYAA
3
AD
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
CONTINUE
DIGITAL 7
TO DIGITAL
MAIN 6
IC3101(5/7)
TO DIGITAL
MAIN 6
IC3101(5/7)
DEMODULATOR
/MPEG
DECODER
DIGITAL MAIN CBA UNIT
(USB JACK)
(HIGH SIDE SWITCH)
(NO CONNECTION)
(NO CONNECTION)
WIRELESS
LAN MODULE
(ETHERNET JACK)
CONTINUE
DIGITAL 8
CONTINUE
DIGITAL 7
Digital Main 5 Schematic Diagram [TYPE A]
PL13.11ASCD5
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-11
AC18
OPEN
D3804
OPEN
C3830
OPENR3807
OPEN
C3810
1C3819
47K
R3825
22K
C3833
OPEN
R3803
0.22C3803
100K
R3812
1
C3823
SP3802
SPEAKER
R-CH
0.047
C3827
OPEN
R3802
1
2
3
4
27
28
26
25
22
24
23
21
6
5
8
7
10
11
12
9
13
14
18
20
15
19
16
17
CONTROL
LOGIC
AVCC
POWER
LIMIT
PWM
LOGIC
DRIVE
GAIN
CONTROL
DRIVE
DRIVE
POWER
LIMIT
PWM
LOGIC
DRIVE
GND
GVDD
NU
PBTL PVCCR
PVCCR
GND
GND
PVCCL
PVCCL
IC3803
TPA3110D2PWPR
L3802
10uH
0.047
C3824
2SC4081UBTLQ
Q3822
1000P
C3814
560
R3820
0.22C3801
1C3816
OPEN
C3808
1C3817
OPENR3805
0R3806
LCD-P-ON
OPEN
D3801
10K
R3824
1
C3822
SP3801
SPEAKER
L-CH
1
C3825
OPEN
R3801
22K
C3832
OPEN
R3826
OPEN
R3804
10
R3813
1
C3821
1000P
C3813
1
C3815
L3803
10uH
1000P
C3812
1C3805
OPEN
C3809
0.22C3804
1
C3820
L3801
10uH
L3804
10uH1C3806
OPEN
C3807
1K
R3811
OPEN
R3810
OPEN
D3802
Q3821
2SA1576UBTLQ
OPEN
D3803
10K
R3808
0.22C3802
1000P
C3811
10K
R3809
OPEN
C3829
1C3818
CN3801
1 SP(L)+
4 SP(R)+
2 SP(L)3 SP(R)-
OPEN
C3837
OPEN
C3835
OPEN
C3836
OPEN
C3834
OPEN
C3840
OPEN
C3841
OPEN
C3839
OPEN
C3838
1
C3828
10K
R3822
560
R3821
AB17
AUDIO-MUTE
OPEN
R3816
OPEN
R3815
OPEN
R3814
OPEN
R3818
OPEN
R3819
OPEN
R3817
P-ON+3.3V
220/16V
C3826
100/16V
C3831
1.8K
R3823
OPEN
R3828
SP-MUTE
E2 AUDIO-MUTE
3.3
R3729
OPEN
C3718
P-ON-H2
220/6.3V
C3712
OPEN
R3744
OPEN
R3732
10K
R3738
4.7K
R3733
47K
R3751
OPEN
Q3708
10K
R3743
OPEN
R3739
OPEN
R3740
OPEN
Q3710
OPEN
R3752
HEADPHONE
JACK
JK3801
OPEN
R3731
3.3
R3728
OPEN
Q3701
R3713
OPEN
220/6.3V
C3713
10K
R3746
10K
R3737
W11
D3704
OPEN
47KR3839
1C3119
R3220 100
1C3105
1C3120
R3145 36
AC14
D3701
OPEN
110
R3726
75
R3171
R3218 10
56P
C3710
D3714 OPEN
1C3121
AC10 NU
AC13
AE17 NU
1C3109
10K
R3724
R3154 100
D3716 OPEN
R3149 36
39P
C3703
33
R3741
D3707
OPEN
1C3102
R3221 100
R3298 100K
100
R3727
JK3701
33P
C3707
220
R3725
10KR3830
AD12 NU
AB13JK3706
Y9 NU
AB16 NU
10K
R3723
R3297 100K
AB14 NU
AB10
IC3101(5/7)
*1
MN2WS0270EA
1C3208
AC11
100P
C3720
75
R3163
10KR3831
10R3214
56P
C3711
AE14
1C3207
D3703
OPEN
47KR3838
AB11
R3219 10
AB12
10K
R3709
2SC4081UBTLQ
Q3709
1C3118
F4
SPDIF
R3222 100
75
R3166
10K
R3708
AD16 NU
D3711 1SS400
D3713 OPEN
1
2
3
4514
13
12
11156
7
8
9
10
JK3713
PC-RGB-IN
AD11
1
C3704
COMP-DET
AC16 NU
D3717 OPEN
R3147 36
R3155 100
D3715 OPEN
Y11 VGA-HSYNC
Y10 NU
1C3103
R3216 10
75
R3164
D3705
OPEN
D3702
OPEN
AA11
75
R3168
1
C3709
AA10
R3148 36
1C3114
AD13
39P
C3770
AE12 NU
1C3104
AC12 NU
39P
C3705
AA12 VGA-VSYNC
100P
C3708
AA9 NU
1C3113
75
R3167
0.01
C3706
AC15 NU
D3712
1SS400
P-ON+5V
AD17
AC17
F5 ARC-OUT
ARC-OUT
E4 NU
D2 NU
F6 NU
G5 NU
E3 NU
R3195 10K
R3196 10K
R3197 10K
R3199 OPEN
VGA-SDA
VGA-SCL
HP-MUTE
HP-DET
AMP+13V
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
SW
AUDIO
I/F
TO DIGITAL
MAIN 8
IC3101(7/7)
A/D
CONVERTER
TO DIGITAL
MAIN 1
IC3101(1/7)
DIGITAL
SIGNAL
PROCESS
TO DIGITAL
MAIN 5
IC3101(4/7)
TO DIGITAL
MAIN 4
IC3101(3/7)
TO DIGITAL
MAIN 3
IC3101(2/7)
TO DIGITAL
MAIN 8
IC3101(7/7)
DIGITAL MAIN CBA UNIT
TO DIGITAL
MAIN 5
IC3101(4/7)
(AUDIO AMP)
3
2
1
4
AE AF AG AH AI AJ
CONTINUE
DIGITAL 8
CONTINUE
DIGITAL 7
CONTINUE
DIGITAL 8
CONTINUE
DIGITAL 4
COMPONENT-Y
/VIDEO-IN
COMPONENT
-Pb-IN
(BUFFER)
AUDIO(L)-IN
COMPONENT
-Pr-IN
AUDIO(R)-IN
DIGITAL
AUDIO OUT
(COAXIAL)
CONTINUE
DIGITAL 2
CONTINUE
DIGITAL 8
CONTINUE
DIGITAL 7
(SWITCHING)
(SWITCHING)
Digital Main 6 Schematic Diagram [TYPE A]
PL13.11ASCD6
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-12
1
2
3
45
6
7
8
IC3603
MP1472GJC452Z
SS
EN
COMB
FB GND
SW
VIN
BST
0.033
C3607
OPEN
C3604
1K
R3605
15K
R3677
6.2K
R3604
L3604
22uH
0.01
C3612
OPEN
C3967
OPEN
R3687
C3614
10
C3603
10
C3608
10
1K
R3628
3300P
C3611
11K
R3606
P-ON+3.3V
P-ON+21V
4.7
C3616
0.1
C3615
OPEN
C3609
4700P
C3666
5.1K
R3635
C3669
OPEN
C3671
10
0.033
C3661
10K
R3633
1
2
3
45
6
7
8
IC3602
MP1472GJC452Z
SS
EN
COMB
FB GND
SW
VIN
BST
4.7
C3674
L3603
10uH
C3670
10
0.01
C3667
OPEN
C3968
100
R3634
OPEN
C3665
0.1
C3675
OPEN
R3685
OPEN
C3673
6.2K
R3679
100K
R3627
C3672
10
C3668
470/4V
C3623
OPEN
1
2
3
45
6
7
8
IC3607
MP1472GJC452Z
SS
EN
COMB
FB GND
SW
VIN
BST
OPEN
C3631
4.7
C3625
33K
R3616
0.1
C3617
C3628
10
OPEN
R3696
0.01
C3620
OPEN
C3966
OPEN
C3618
4700P
C3619
C3621
10
12K
R3678
L3605
22uH
4.3K
R3614
10K
R3617
0.1
C3632
D3615
CRY68
D3606
1SS400
OPEN
C3644
0.015
C3601
2.2K
R3625
OPEN
C3654
0.01
C3639
OPEN
R3613
OPEN
R3676
OPEN
C3642
0
R3626
C3641
10
OPEN
R3624
4.7
C3645
1
2
3
45
6
7
8
IC3604
RT8293ALZSP
BS
VIN
SW
GND FB
COMP
EN
SS
10
C3643
0.015
C3638
L3601
10uH
0.1
C3656
0.1
C3655
OPEN
R3689
OPEN
C3969
C3646
OPEN
100R3629
20P-ON+21V
14GND
22P-ON+21V
3PROTECT3
7BACKLIGHT-ADJ
17AMP+13V
9GND
12GND
8AL+3.3V
6P-ON-H2
10GND
21P-ON+21V
4RESET
5BACKLIGHT-SW
OPEN
C3650
23P-ON+21V
2PROTECT1
13GND
16AMP+13V
OPEN
C3652
19GND
OPEN
C3676
100R3647
11GND
18AMP+13V
15AMP+13V
CN3601
1LED-CONT(NU)
100R3620
100R3603
32
14
IC3601
PST8429UR
CDVDD
GND OUT
270
R3608
D3603
OPEN
1
C3602
R3602
220
0.01
C3606
56K
R3607
OPEN
R3621
10K
R3619
4.7K
R3618
2SC4081UBTLQ
Q3603
1
C3610
D3608
1SS400
D3609
OPEN
BACKLIGHT-ADJ
STB-RESET
HP-MUTE
LCD-P-ON
BACKLIGHT-SW
P-ON-H2
PROTECT3
PROTECT1
2SA1576UBTLQ
Q3602
D3605
MM5Z15B
10K
R3615
10K
R3622
OPEN
C3613
0
R3630
0
R3631
D3607
OPEN
10K
R3095
1000P
C3605
100R3645
D3602 OPEN
D3601
OPEN
R3601
OPEN
OPEN
Q3601
R3610
OPEN
OPEN
R3612
10K
R3609
R3611
OPEN
AUDIO-MUTE
1
C3146
1
C3184
10
C3173
1
C3138
M9VDDTCON25-33
AB15AVDDEVE33
N13VDD33-2
1
C3141
*BVDDIO15
0R3022
0.1
C3131
M12DPAVDD33
L11LVVDD33-1
*DGND
K11LVVDD11
T16AVDDHP33
0R3024
AB21AVDDH33
R3181
0
*AVDD11
1
C3132
R16AVDDAPUSB33
N9FPEN
*CNU
N10VDDSTM11
0.1
C3154
1
C3145
10
C3136
1
C3143
U12AVDDVAD11
U15AVDDV33
L3108
BEAD
AVDDADA33 T15
1
C3152
1
C3172
R15AVDDPLL33
0.1
C3130
J21VDDSD18-33
R12TESTSEL
1
C3137
10
C3142
L10VDDSTM33
D5VDDIOCK15
1
C3134
1
C3140
1
C3144
M11LVVDD33-2
0R3023
1
C3151
10
C3153
1
C3175
M13VDDEM18-33
N12VDD33-1
1
C3150
1
C3185
L3102
0
AC21AVDDH11
AD21AVDDH11
OPEN
C3133
AFB R4
IC3101(6/7)
*1
MN2WS0270EA
0
R3223
OPEN
C3183
2700P
C3182
T9AVDD11-CEN
AB4AVDD11-RX
T10DVDD11
0.1
C3147
0.1
C3148
0.1
C3149
CTRL11
N11LVVDD33-3
AVDDDMD33 U11
AVDD33-CEN P10
AVDD33-TX P9
STMADAVDD33 M10
STMRONA T4
10
C3156
1
C3178
0.1
C3157
1
C3179
0.1
C3158
0.1
C3155
L3103
2.2uH
L3104
BEAD
10
C3159
0.1
C3160
0.1
C3161
0.1
C3162
0.1
C3163
L3105
BEAD
0.1
C3164
560
R3185
10
C3135
10
C3165
0.1
C3167
10
C3166
0
R3183
0.1
C3169
0.1
C3170
0.1
C317110C3177
0
R3184
0.1
C3168
0.1
C3174
W9VCOMP
J4LVDSRREF
L22USBRREF
AD14VREF1V5
24KR3186
1C3180
6.2KR3187
1C3181
HP-MUTE
LCD-P-ON
1
C3139
22K
R3623
OPEN
C3630
AL+3.3V
VCC+1.5V
P-ON+21V
P-ON+3.3V
P-ON+3.3V
P-ON+5V
AL+3.3V
P-ON+3.3V
P-ON+5V
P-ON+5V
P-ON+3.3V
AMP+13V
P-ON+3.3V
AL+3.3V
P-ON+5V
D3610
MM5Z4V3B
L3101
BEAD
L3107
BEAD
L3106
BEAD
APAOANAMALAK
4
3
1
2
DIGITAL MAIN CBA UNIT
(+3.3V REG.)
(+1.5V REG.)
(+5V REG.)
(+1.14V REG.)
TO POWER SUPPLY
CBA CN501
(RESET)
(SW+12V)
CONTINUE
DIGITAL 1
CONTINUE
DIGITAL 8
*A:J11~J17,K12~K17,L14~L17,M15~M17
*B:E9,F8,F9,G13~G15,G19
HEAT SINK
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
*C:H5,P23,R13,R23,R24,T13,T22,T23,U22,U24,U25,
V5,AD1,AD2,AE2
*D:A1,A9,A25,C10,D13,E5,E6,E12,E13,F7,F13,F15,
G17,G18,H7,H8,J9,J10,K9,K10,L9,L12,L13,M14,
N6,N7,N14~N17,P11~P17,R10,R11,R14,R17,T11,
T12,T14,T17,U13,U14,U16,U17,W12,W13,Y14,
AA14,AC4,AE1,AE25
CONTINUE
DIGITAL 5
CONTINUE
DIGITAL 6
CONTINUE
DIGITAL 1
CONTINUE
DIGITAL 3
CONTINUE
DIGITAL 2
CONTINUE
DIGITAL 4
CONTINUE
DIGITAL 5
CONTINUE
DIGITAL 6
CONTINUE
DIGITAL 8
(SWITCHING)
Digital Main 7 Schematic Diagram [TYPE A]
PL13.11ASCD7
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-13
47K
R3774
47K
R3773
10K
R3777
0.1
C3750
47K
R3778
47K
R3780
10K
R3784
47K
R3785
47K
R3781
0.1
C3759
47K
R3706
47K
R3718
0.1
C3702
47K
R3722
10K
R3721
16 HDMI-DATA
12 CLOCK(-)
JK3717
1 DATA2(+)
6 DATA1(-)
3 DATA2(-)
14 ARC
9 DATA0(-)
10 CLOCK(+)
7 DATA0(+)
5 TMDS DATA1 SHIELD
17 GND
18 +5V
13 HDMI-CEC
15 HDMI-CLOCK
19 HOT PLUG DETECT
2 TMDS DATA2 SHIELD
4 DATA1(+)
11 TMDS CLOCK SHIELD
8 TMDS DATA0 SHIELD
16 HDMI-DATA
12 CLOCK(-)
JK3716
1 DATA2(+)
6 DATA1(-)
3 DATA2(-)
14 NU
9 DATA0(-)
10 CLOCK(+)
7 DATA0(+)
5 TMDS DATA1 SHIELD
17 GND
18 +5V
13 HDMI-CEC
15 HDMI-CLOCK
19 HOT PLUG DETECT
2 TMDS DATA2 SHIELD
4 DATA1(+)
11 TMDS CLOCK SHIELD
8 TMDS DATA0 SHIELD
14 NU
17 GND
19 HOT-PLUG-DETECT
15 HDMI-CLOCK
18 HDMI+5V
16 HDMI-DATA
2 TMDS DATA2 SHIELD
10 CLOCK(+)
JK3715
1 DATA2(+)
4 DATA1(+)
7 DATA0(+)
5 TMDS DATA1 SHIELD
8 TMDS DATA0 SHIELD
11 TMDS CLOCK SHIELD
3 DATA2(-)
13 HDMI-CEC
6 DATA1(-)
12 CLOCK(-)
9 DATA0(-)
AD24
IC3101(7/7)
MN2WS0270EA
*1
AE24
AD23
AE23
AC23
AE22
AD22
AC22
22
R3865
27K
R3863
D3722
1SS400
2SC4081UBTLQ
Q370710K
R3701
1K
R3705
OPEN
R3719
10K
R3703
AB24
AA23
AA24
AC24
AD25
Y23
AC25
AB25
1K
R3779
OPEN
R3783
2SC4081UBTLQ
Q370210K
R3707
10K
R3710
W23
V23
V24
Y25
Y24
U23
W22
V22
OPEN
R3776
1K
R3775
2SC4081UBTLQ
Q370310K
R3711
10K
R3712
2SC4081UBTLQ
Q370410K
R3714
33K
R3720
OPEN
Q3706
UART1TX
0
R3730
OPEN
R3772
10K
R3715
2SC4081UBTLQ
Q3705
33K
R3716
UART1RX
0
R3717
Y3HDMI-CEC
T6STMCECPUL
T7HDMI0-SCL
39R3134
39R3137
W6HDMI0-SDA
R9HDMI1-SCL
39R3139
AE3HDMI1-SDA
39R3140
V7HDMI2-SCL
AA5HDMI2-SDA
39R3141
39R3142
R7HDMI0-HPD
U2HDMI1-HPD
U6HDMI2-HPD
ARC-OUT
AA6HDMI1-5V
AC3HDMI2-5V
AB5HDMIO-5V
Y6HDMI-UART-CTRL
OPEN
R3771
100R3179
10K
R3002
1
C3012
82
R3008
160
R3014
220P
C3719
220P
C3717
100K
R3212
U5 PROTECT1
STB-RESET
AA2 SP-MUTE
OPEN
C3107
OPEN
C3110
10K
R3151
U1 KEY-IN1
OPEN
D3101
100
R3107
1
2
3
45
6
7
8
IC3103
M24C16-WMN6TP
A0
A1
A2
VSS SDA
SCL
WP
VCC
W3 BACKLIGHT-SW
39R3157
AB6 P-ON-H2
OPENC3122
BACKLIGHT-SW
10
R3117
8P-ON+5V
0
R3159
U3 REMOTE
P-ON-H2 2
4.7K
R3152
T3 LIGHT-SENS
PROTECT3
U4 STM-EEPROM-WP
PROTECT3
SP-MUTE
P-ON+5V
C3127
0.1
AC1 STM-SDA
2SC4081UBTLQ
Q3101
0.1
C3111
33
R3110
1K
R3102
2SCL(NU) V3 LED1
5REMOTE
33
R3323
100R3133
P-ON+3.3V
39R3156
Y2 P-ON-H2
33
R3114
1
C3108
6LED1
22R3158
AD5 STB-RESET
HP-MUTE
100R3161
100K
R3146
100R3160
10K
R3106
4KEY-IN1
10K
R3103
PROTECT1
OPENC3123
CN3105
1SDA(NU)
7LIGHT
3GND
P-ON-H2
2SC4081UBTLQ
Q3102
27K
R3104
CN3103
AL+3.3V 1
AC2 STM-SCL
9AL+3.3V
T2 PROTECT3
OPEN
C3112
4.7K
R3153
100
R3105
OPEN
R3119
C3106
33/10V OPEN
R3182
0.1
C3101
22K
R3096
1K
R3131
W7 HP-MUTE
OPENR3138
OPEN
Q3103
OPEN
R3120
OPEN
R3143
W4 LED2
W5 STMTIME1
OPEN
R3207
OPEN
R3188
Y5 SW-EN
AA4 NU
Y1 NU
AB1 NU
AB3 NU
AB2 NU
Y4 NU
V6 NU
AA3 NU
V4 NU
10KR3109
Y7VGA-SCL
AD3VGA-SDA
U7NU
39R3165
39R3178
VGA-SDA
VGA-SCL
STB-RESET
STMTIME1
22R3162
W2 LCD-P-ONLCD-P-ON
10K
R3150
AL+3.3V
Q3107
OPEN
OPEN
R3200
OPEN
R3209
0
R3144
OPEN
Q3108
OPEN
R3215
OPEN
R3206
C3100
OPEN
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
HDMI
I/F
HDMICONNECTOR-1
HDMICONNECTOR-3
HDMICONNECTOR-2
AQ
DIGITAL MAIN CBA UNIT
(SWITCHING)
(SWITCHING)
(SWITCHING)
CONTINUE
DIGITAL 6
CONTINUE
DIGITAL 5
2
4
1
3
AR AS AT AU AV
TO DIGITAL
MAIN 6
IC3101(5/7)
VIDEO
DECODER
AUDIO
DECODER
TO DIGITAL
MAIN 6
IC3101(5/7)
(SWITCHING)
(SWITCHING)
TO FUNCTION CBA
UNIT CN4052
(MEMORY)
CONTINUE
DIGITAL 7
(NO CONNECTION)
(LED DRIVE)
CONTINUE
DIGITAL 7
CONTINUE
DIGITAL 6
CONTINUE
DIGITAL 4
CONTINUE
DIGITAL 6
CONTINUE
DIGITAL 2
(BUFFER)
Digital Main 8 Schematic Diagram [TYPE A]
PL13.11ASCD8
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-14
12K
R3045
11K
R3044
3.9K
R3047
12K
R3046
47/25V
C3057
P-ON+21V
VCOM-PWM
P-ON+3.3V
CELL-PWR-CTRL
0.1
C3058
1
2
3
45
6
7
8
IC3621
OPEN
SS
EN
COMP
FB GND
SW
IN
BST
OPEN
C3626
OPEN
C3630
OPEN
R3628
OPEN
C3625
OPEN
R3627
D3621
OPEN OPEN
C3633
OPEN
C3636D3622
OPEN OPEN
C3632
OPEN
R3631 C3631
OPENOPEN
C3635
OPEN
C3634
OPEN
R3629
L3621
OPEN
OPEN
C3624
OPEN
C3623
OPEN
C3622
OPEN
C3621
OPEN
C3627
OPEN
R3622
OPEN
C3628
OPEN
R3621
OPEN
R3623
OPEN
C3629
OPEN
R3624
OPEN
R3625
OPEN
R3626
OPEN
D3623
OPEN
R3632
D3624
OPEN
0
R3630
PROTECT3
OPEN
D3008
OPEN
C3000
1K
R3048
3NU
48 LCD+21V
39 RXE0(+)
34 GND
20 RXO2(-)
13 RXO3(+)
35 RXE2(+)
11 NU
12 NU
15 GND
27 NU
6GND
17 RXOCLK(-)
19 RXO2(+)
36 RXE2(-)
31 GND
9NU
23 RXO0(+)
14 RX03(-)
5NU
50 LCD+21V
28 NU
47 NU
7GND
49 LCD+21V
21 RXO1(+)
8GND
33 RXECLK(-)
26 NU
29 RXE3(+)
16 RXOCLK(+)
CN3013
1NU
24 RXO0(-)
18 GND
10 NU
43 P-ON+3.3V
30 RXE3(-)
32 RXECLK(+)
4NU
25 NU
42 NU
38 RXE1(-)
2NU
41 GND
44 P-ON+3.3V
40 RXE0(-)
37 RXE1(+)
45 VCOMA
51 NU
22 RXO1(-)
46 DCDC-EN
0R3165
OPEN
C3162
OPEN
R3130
0
R3171
0R3170
1000P
C3167
4.7
C3166
2SC4081UBTLQ
Q3007
OPEN
R3042
0R3166
0R3167
4NU
2NU
CN3602
1GND
3NU
OPEN
C3161
0R3173
0R3174
OPEN
C3641
OPEN
C3642
OPEN
C3643
OPEN
C3644
OPEN
C3645
OPEN
C3646
OPEN
C3647
L15OE
N13NU
M16NU
L13TP
M15POL
M14STV
N14NU
M13NU
L14OE2
L16CPV
OPEN
C3171
OPEN
C3170
OPEN
R3172
OPEN
R3129
0
R3434
0R3432
0R3433
OPENR3430
OPENR3431
OPENR3435
OPENR3436
OPENR3438
OPENR3437
OPENR3441
OPENR3442
3PC3662
3PC3663
R13
T13
R14
T14
T16
T15
R15
R16
P16
P15
N16
N15
P14
P13
K15
*1
IC3005(1/6)
R8A05011BG-U0
NU
OPEN
C3673
OPEN
C3675
OPEN
C3674
OPEN
C3672
OPEN
C3676
OPENR3439
OPENR3440
0
R3168
3PC3664
3PC3665
3PC3666
3PC3667
3PC3668
3PC3669
3PC3670
3PC3671
OPENC3648
OPENC3649
3PC3650
3PC3651
3PC3652
3PC3653
3PC3654
3PC3655
3PC3656
3PC3657
3PC3658
3PC3659
OPENC3660
OPENC3661
7.5K
R3088
0
R3169
OPEN
R3524
A
4
E
2
DCB
1
F
3
CONTINUE
DIGITAL 4
DIGITAL MAIN CBA UNIT
CONTINUE
DIGITAL 3
(SWITCHING)
(NO CONNECTION)
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
TO DIGITAL
MAIN 2
IC3005(2/6)
LVDS
TX
TO LCD PANEL
ASSEMBLY
Digital Main 1 Schematic Diagram [TYPE B]
PL13.11BSCD1
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-15
B12
D3045
OPEN
D3049
OPEN
A10NU
D9NU
D3053
OPEN
4.7K
R3321
C8NU
0.1C3195
B9NU
75
R3364
10K
R3358
B11
75
R3377
A12
C10
B14VSYNC
A16IF-AGC
D10NU
D8
A14HSYNC
47
R3284
C9
A11NU
D3050
OPEN
C11
B10NU
A9
D3054
OPEN
47
R3285
10
R3333
C7
10
R3334
1
2
34
VCC
GND
5
IC3013
74LVC1G126GW
47
R3286
10K
R3347
0.1C3196
1
2
34
VCC
GND
5
IC3014
74LVC1G126GW
75
R3356
4.7K
R3326
D3055
OPEN
0.1C3194
OPEN
R3701
OPEN
R3702
OPEN
R3703
100K
R3705
100K
R3704
D3041
OPEN
0.1C3201
0.01C3198
0.1C3200
0.1C3199
0.1C3286
0.1C32852.2
C3335
1C3336
1K
R3194
10
R3250
2.7K
R3202
10
R3251
0.1
C3178
18K
R3205
SDA T12
L3913
2.2uH
OPEN
C3934
0.1C3903
0.1C3902
1000P
C3910 D3904
MM5Z5V6B
SCL R12
IC3005(2/6)
R8A05011BG-U0
*1
47R3206
47R3207
33P
C3176
33P
C3175
2.7K
R3204
2.7K
R3203D3903
MM5Z5V6B
OPEN
C3909
D3902
MM5Z5V6B
0.1
C3214
10
R3332
10
R3331
10R3327
10R3328
10R3329
P-ON+5V
P-ON+3.3V
AUDIO(L)-IN
AUDIO(R)-IN
COMP-DET
SPDIF
VGA-SCL
VGA-SDA
1
2
3
4514
13
12
11156
7
8
9
10
JK3001
PC-RGB-IN
JK3702
TU3901 (TUNER UNIT)
1
+3.3V2GND3SDA4SCL5IF-AGC6DIF-OUT17DIF-OUT2
33P
C3173
33P
C3172
Q3302
2SK3018
Q3301
2SK3018
2SC4081UBTLQ
Q3701
0.1
C3708
10K
R3711
100
R3710
220
R3709
110
R3708
1
C3706
100P
C3709
JK3701
SDA
SCL
10K
R3712
1
C3707
33P
C3287
33P
C3291
33P
C3293
33P
C3292
33P
C3289
33P
C3288
OPEN
R3339
OPEN
R3296
OPEN
R3343
OPEN
R3298
75
R330275R330375R3301
10
C3905
220/6.3V
C3901
1
C3177
D3901
MM5Z5V6B
4
JI
3
2
L
1
GH K
DIGITAL MAIN CBA UNIT
DIGITAL
SIGNAL
PROCESS
TO DIGITAL
MAIN 6
IC3005(6/6)
TO DIGITAL
MAIN 1
IC3005(1/6)
TO DIGITAL
MAIN 5
IC3005(5/6)
(BUFFER GATE)
(BUFFER GATE)
CONTINUE
DIGITAL 4
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
SW
A/D
CONVERTER
DEMODULATOR
/MPEG
DECODER
AUDIO(L)-IN
AUDIO(R)-IN
COMPONENT
-Pr-IN
COMPONENT
-Pb-IN
COMPONENT
-Y/VIDEO-IN
CONTINUE
DIGITAL 3
CONTINUE
DIGITAL 5
CONTINUE
DIGITAL 5
CONTINUE
DIGITAL 6(BUFFER)
(BUFFER)
(BUFFER)
DIGITAL
AUDIO-OUT
(COAXIAL)
TO DIGITAL
MAIN 3
IC3005(3/6)
TO DIGITAL
MAIN 3
IC3005(3/6)
Digital Main 2 Schematic Diagram [TYPE B]
PL13.11BSCD2
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-16
IC3002
K4T51163QJ-BCE7
*A VDD
J2VREF
E2 NU
K2CKE
J8CK
K8CK
L8CS
K7RAS
L7CAS
K3WE
L1BA2/NU
L3BA1
L2BA0
R2A12
P7A11
M2A10/AP
P3A9
P8A8
P2A7
N7A6
N3A5
N8A4
N2A3
M7A2
M3A1
M8A0
K9ODT
*BVSS
A2 NU
R8 NU
R7 NU
R3 NU
B7 UDQS
A8 UDQS/NU
B3 UDM
B9 DQ15
C2 DQ11
C8 DQ8
F7 LDQS
E8 LDQS/NU
F3 LDM
F9 DQ3
F1 DQ2
H9 DQ7
H1 DQ6
H3 DQ4
H7 DQ1
G2 DQ5
G8 DQ0
N8 SD-DQ14
P7 SD-DQ13
R6 SD-DQ12
P6 SD-DQ11
N7 SD-DQ10
T5 SD-DQ9
P8 SD-DQ8
P4 SD-DQ7
T3 SD-DQ6
R4 SD-DQ5
T2 SD-DQ4
P3 SD-DQ3
T4 SD-DQ2
R3 SD-DQ1
N4 SD-DQ0
T6 SD-UDM
R5 SD-LDM
T7 SD-UDQSN
R7 SD-UDQS
N5 SD-LDQSN
P5 SD-LDQS
J3 SD-RAS
H3 SD-CAS
L4 SD-WE
R1 SD-CLKN
R2 SD-CLK
L3 SD-CKE
K2 SD-ODT
M2 SD-A12
P1 SD-BA2
L1 SD-A1
H1 SD-A4
K1 SD-A2
H2 SD-A8
L2 SD-A9
N1 SD-A7
K4 SD-BA1
J2 SD-A11
K3 SD-A6
J1 SD-A0
M3 SD-A3
J4 SD-A10
N2 SD-BA0
M1 SD-A5
0.1
C3010
1
2
3
45
6
7
8
IC3006
S25FL032P0XMFI010
CS
SO
WP
GND SI
SCK
NU
VCC
1
C3246
0.1C3029
0.1C3030
0.1C3031
0.1C3032
0.1C3033
0.1C3034
0.1C3035
0.1C3037
0.1C3038
0.1C3039
0.1C3040
0.1C3041
H4 NU
G16RXD0
4.7K
R3395
4.7K
R3396
G15TXD0
10K
R3107
10K
R3102
L3025
EXC24CG900U
E2BACKLIGHT-SW
22R3188
G13HP-MUTE
10K
R3503
IC3005(3/6)
R8A05011BG-U0
*1
M5 SD-VREF0
R8 SD-DQ15
N3 GND
0.1
C3051
100
R3065
0.1
C3050
100
R3064
D14LED1
0.1
C3073
F15ASEBRKAK-N
F16ASEMD0
E16TRST-N
E15TCK
D16TDI
D15TDO
E14TMS
E13GPY10
C1AUDIO-MUTE
OPEN
R3234
22R3217
F3BACKLIGHT-ADJ
100R3516
4.7KR3515
J14GND
H15XIN25
H16XOUT25
1K
R3223
X3001
25MHz
18P
C3184
20P
C3183
100R3468
100R3469
10K
R3522
1
2
34
5
IC3019
AP2151WG-7
OUT
GND
/FLAG RN
IN
220/6.3V
C3348
10K
R3480
10K
R3479
OPEN
C3009
F2VCOM-PWM
100R3517
N12COMP-DET
22R3215 33K
R3201
D1CELL-PWR-CTRL
B16P-ON-H2
100R3211
22R3213
C14REMOTE
T9 VBUS-EN
T11 SCK
P10 NU
R10 USBDP
P12 CS
T10 USBDN
R9 VBUS-ST
R11 SOUT
P11 SIN
5.6KR3099
47R3093
47R3094
47R3092
22R3095
47R3089
H14NU
10C3072
OPEN
C3253
P-ON+5V
P-ON+3.3V
AL+3.3V
P-ON+1.8V
BACKLIGHT-SW
LED1
GPY10
BACKLIGHT-ADJ
VCOM-PWM
COMP-DET
P-ON-H2
REMOTE
CPU-RESET-N
CPU-RESET-N
3USBDP
4GND
2USBDN
CN3009(USB JACK)
1BUS-POWER
2 UART0-TX
3 UART0-RX
4 GND
CN3010
1 P-ON+5V
4 ASEMD0
5 TRST-N
6 TCK
3 ASEBRKAK-N
9 TMS
8 TDO
7 TDI
CN3012
AL+3.3V1
2 GND
10 CPU-RESET-N
OPEN
C3255
OPEN
C3254
22R3511
22R3233
22KR3510
0.1C3140
D1 DQ9
D3 DQ14
D7 DQ13
B1 DQ12
D9 DQ10
1
C3327
100
R3083
100
R3082
R3033 33x4
R3030 33x4
R3031 33x4
R3032 33x4
R3034 33x4
33R3016
10R3084
10R3087
150R3070
150
R3049
OPENR3527
OPENR3525
OPENR3526
BACKLIGHT-SW
HP-MUTE
AUDIO-MUTE
CELL-PWR-CTRL
DIGITAL MAIN CBA UNIT
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
(DDR2 SDRAM)
*B:A3,A7,B2,B8,D2,D8,E3,E7,
F2,F8,H2,H8,J3,J7,N1,P9
*A:A1,A9,C1,C3,C7,C9,E1,E9,
G1,G3,G7,G9,J1,J9,M9,R1
1-O3
2-O3
3-O3
4-O3
5-O3
6-O3
SD-DQ15
SD-DQ11
SD-DQ8
SD-DQ3
SD-DQ2
SD-DQ7
SD-DQ6
SD-DQ4
SD-DQ1
SD-DQ5
SD-DQ0
SD-DQ2
SD-DQ5
SD-DQ1
SD-DQ4
SD-DQ0
SD-DQ7
SD-DQ3
SD-DQ6
SD-DQ13
SD-DQ9
SD-DQ12
SD-DQ8
SD-DQ15
SD-DQ11
SD-DQ14
SD-DQ10
1-M3
2-M3
3-M3
4-M3
5-M3
6-M3
(MEMORY)
CONTINUE
DIGITAL 4
2
MP
1
NO
3
4
QR
(NO CONNECTION)
CONTINUE
DIGITAL 4
CONTINUE
DIGITAL 2
CONTINUE
DIGITAL 5
(NO CONNECTION)
CONTINUE
DIGITAL 5
(HIGH SIDE SW)
TO DIGITAL
MAIN 2
IC3005(2/6)
TO DIGITAL
MAIN 2
IC3005(2/6)
SD-DQ14
SD-DQ13
SD-DQ12
SD-DQ10
SD-DQ9
CONTINUE
DIGITAL 5
CONTINUE
DIGITAL 1
Digital Main 3 Schematic Diagram [TYPE B]
PL13.11BSCD3
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-17
1
C3124
OPEN
C3321
1
C3157
J5VCCQ18
M4VCCQ18
D6AVDD33
F12
IC3005(4/6)
R8A05011BG-U0
*1
VCC33STB
F8AVDD12
1
C3148
0.1
C3160
1
C3150
1
C3123
M6VCCQ18
F9AVDD12
1
C3151
1
C3141
10
C3320
OPEN
C3264
F5VCCQ33
C2AVDD33
J12VCCQ33
E10AVDD33
E8AVDD12
N11AVDD33
1
C3145
E12VDD12STB
1
C3129
10
C3343
G4VCCQ33
C3142
1
10
C3319
M7VCCQ18
M8VCCQ18
10
C3326
*DVSS
10
C3149
OPEN
C3324
G12VCC33STB
T1VCCQ18
*CVDD12
1
C3143
H5VCCQ18
G11VDDCLK
E6AVDD33
1
C313610C3114
E11AVDD33
1
C3144
OPEN
C3325
10
C3322
1
C3158
1
C3128
0.1
C3181
C3AVDD33
1
C31301C3134
M10AVDD12
0.1
C3135
10
C3115
0.1
C3139
N6VCCQ18
10
C3318
1
C3152
L12VCCQ33
K13VCCQ33
10K
R3222
1
C3131
4.7K
R3086
10K
R3077
10K
R3079
47K
R3106
10K
R3105
D3101
HSC119
D3102
HSC119
22K
R3100
D3103
HSC119
47K
R3423
100
R3424
1.5K
R3097
D3106
HSC119
D3104
HSC119
D3105
OPEN
OPENC3008
OPENC3006
OPENC3004
OPENC3055
OPENC3048
220R3013
OPENR3011
100R3009
100R3072
100R3068
OPENC3062
OPEN
C3995
OPEN
C3996
100
R3051
OPEN
D3007
MM5Z12B
D3112
47K
R3108
10K
R3112
10K
R3113
1K
R3101
1
C3107
47K
R3114
1K
R3104
OPEN
R3115
Q3013
SSM3K309T
G
DS
Q3003
2SC4081UBTLQ
Q3004
2SC4081UBTLQ
Q3005
2SC4081UBTLQ
Q3101
2SC4081UBTLQ
Q3102
2SC4081UBTLQ
Q3006
2SA1576UBTLQ
Q3103
2SA1576UBTLQ
P-ON+5V
AL+3.3V
P-ON+21V
P-ON+3.3V
P-ON+1.8V
P-ON+3.3V(1)
BACKLIGHT-SW
BACKLIGHT-ADJ
PROTECT1
PROTECT3
RESET
P-ON-H2
CPU-RESET-N
GPY10
AMP+13V
P-ON+3.3V
AL+3.3V
P-ON+5V
P-ON+5V
P-ON+3.3V
AL+3.3V
P-ON+3.3V
P-ON+3.3V(1)
15 GND
13 GND
8 AMP+13V
12 GND
16 AL+3.3V
20 RESET
18 P-ON-H2
5 GND
7 AMP+13V
6 AMP+13V
22 PROTECT1
11 GND
17 BACKLIGHT-ADJ
CN3701
23 LED-CONT(NU)
10 GND
21 PROTECT3
14 GND
19 BACKLIGHT-SW
9 AMP+13V
0
L3030
10
C3118
1
C3154
MM5Z5V6B
D3114
100
R3221
D3115
HSC119
1
C3125
D3994 OPEN
OPEN
C3063
OPEN
C3994
CHECK+1.8V
100
R3036
Q3009
2SC4081UBTLQ
OPEN
C3238
D3107
HSC119
18K
R3140
1K
R3139
Q3011
OPEN
OPEN
R3227
OPEN
R3228
OPEN
C3237
1
2
3
45
6
7
8
IC3004
BD00IA5WEFJ-E2
VOUT
FB
GND
NU EN
NU
NU
VCC
0.022
C3019
1.8K
R3062
2.7K
R3060
2.7K
R3059
10
C3086
10K
R3061
180
R3043
C3079
220/6.3V
1
2
3
45
6
7
8
IC3007
BD00IC0WEFJ
VOUT
FB
GND
NU EN
NU
NU
VCC
10
C3069
10
C3087
0.022
C3075
3.3K
R3109
10K
R3110
10K
R3111
1.8K
R3103
10
C3024
L3003
OPEN
10
C3265
OPEN
R3138
P-ON+3.3V
4 P-ON+21V
3 P-ON+21V
1 P-ON+21V
2 P-ON+21V
PROTECT3
L3027
BEAD
L3021
BEAD
L3019
OPEN
L3026
BEAD
P-ON+5V
1
C3159
L3006
BEAD
1
C31551C3156
MM5Z5V6B
D3113
1
C3126
1
C3127
10
C313210C3133
C3068
OPEN
1
R3008
1
2
3
45
6
7
8
IC3001
MP1472GJC452Z
SS
EN
COMP
FB GND
SW
IN
BST
0.1
C3003
OPEN
C3002
4.7
C3102
0.047
C3013
OPEN
C3119
0
R3091
8.2K
R3001
2200P
C3017
33K
R3004
6.2K
R3003
15K
R3002
0.1
C3014
OPEN
R3057
OPEN
C3092
OPEN
C3605
OPEN
R3601
L3002
33uH
C3020
330/4V 10
C302110C3059
270
R3014
PTZTE255.1B
D3005
1
C3090
10K
R3133
4700P
C3088
PTZTE255.1B
D3006
1
2
3
45
6
7
8
IC3008
MP1472GJC452Z
SS
EN
COMP
FB GND
SW
IN
BST
2.7K
R3137
0.015
C3083
3.9K
R3149
1.2K
R3145
15K
R3143
OPEN
C3097
10
C3096C3094
330/4V 10
C3065
OPEN
C3606
OPEN
R3602
L3009
10uH
OPEN
C3099
OPEN
R3142
0.1
C3085
OPEN
C3091
OPEN
R3141
4.7
C3080
OPEN
C3103
0.1
C3007
4.3K
R3005
OPEN
C3121
1
2
3
45
6
7
8
IC3003
MP1472GJC452Z
SS
EN
COMP
FB GND
SW
IN
BST
4700P
C3043
0.047
C3028
0
R3098
12K
R3007
33K
R3012
10K
R3006
10
C305610C3074
OPEN
C3053
0.1
C3042
OPEN
R3054
OPEN
C3095
0.1
C3001
4.7
C3022
OPEN
C3105
L3005
22uH
OPEN
C3607
OPEN
R3603
4.7K
R3608
OPEN
R3607
OPEN
C3611
1
C3610
OPEN
R3606
IC3601
AP2121AK-3.3TRE1
1 VIN
2 GND
3CE 4NU
5VOUT
1
C3609
0
R3605
OPEN
R3609
D3995 OPEN
1
R3071
MM5Z4V3B
D3602
1
C3603
10
C3604
XU
4
1
3
2
WSVT
DIGITAL MAIN CBA UNIT
(SW+12V)
*C:G5,G6,H6,J7,J11,J13,K6,K7,
K11,L8,L9,M9,M11,N9,P9.
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
*D:D2~D5,D12,E3~E5,E7,E9,F4,F6,
F7,F10,F11,G7~G10,H7~H13,J6,
J8~J10,K5,K8~K10,K12,L5~L7,
L10,L11,P2,T8
(SWITCHING)
(SWITCHING)
(SWITCHING)
(SWITCHING)
(SWITCHING)
TO POWER SUPPLY
CBA CN501
CONTINUE
DIGITAL 3
CONTINUE
DIGITAL 5
CONTINUE
DIGITAL 5
CONTINUE
DIGITAL 1
CONTINUE
DIGITAL 3
CONTINUE
DIGITAL 2
CONTINUE
DIGITAL 6
(SWITCHING)
(SWITCHING)
(+1.2V REG.)
(+1.8V REG.)
(SWITCHING)
(+3.3V REG.)(+1.2V REG.)
(+5V REG.)
(+3.3V REG.)
Digital Main 4 Schematic Diagram [TYPE B]
PL13.11BSCD4
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-18
100
R3551
OPEN
R3555
100
R3209
A8
B7
B8
A13 LIGHT-SENS
C13 PROTECT1
A7
C12 LPF
A15 KEY-IN1
22R3316
22R3315
2.2C3218
2.2C3217
10KR3319
22KR3318
10K
R3184
39K
R3186
10K
R3185
100
R3183
10
C3558
18KR3335
1000PC3232
18KR3336
1000PC3233
OPENC3227
OPENC3229
OPEN
C3559
OPEN
C3556
10KR3312
B13 PROTECT3
22R3314
SP3801
SPEAKER
L-CH
N10
B6NU
A6NU
D7NU
C6NU
D11NU
C5NU
10C3220
10C3219
10KR3340
10C3216
OPEN
C3328
4KEY-IN1
5REMOTE
3GND
3 SP(R)-
2 SP(L)-
4 SP(R)+
CN3801
1 SP(L)+
AUDIO-MUTE
LED1
REMOTE
AL+3.3V
P-ON+5V
SPDIF
PROTECT3
P-ON+3.3V(1)
AUDIO(R)-IN
AUDIO(L)-IN
AMP+13V
RESET
PROTECT1
2SC4081UBTLQ
Q3501
Q3010
2SC4081UBTLQ
D13 CHECK+1.8V
IC3005(5/6)
*1
R8A05011BG-U0
HEADPHONE
JACK
JK3703
SP3802
SPEAKER
R-CH
10
R3561
0.01C3329
100
R3553
10KR3317
100
R3552
9AL+3.3V
8P-ON+5V
7LIGHT
6LED1
2SCL(NU)
CN3101
1SDA(NU)
CHECK+1.8V
MM5Z5V6B
D3501
1
C3554
2SA1576UBTLQ
Q3502
OPEN
R3558
10K
R3559
100K
R3560
OPEN
C3555
SDA
SCL
10
R3557
10
R3556
33PC3551
33PC3552
OPEN
C3553
K14HPD-SINK
100
R3210
22
R3219
K16HP-DET
100
R3216
J16PWR
P-ON+3.3V
E1NU
G1NU
HPD-SINK
PWR
OPEN
R3320
0.22C3231
1C3223
OPENR3501
1C3224
OPENR3502
MM5Z5V6B
D3201
33K
R3220
0
R3402
0
R3401
G2NU
8
3
VCC
4
GND5MUTE
6
1
BIAS
7
2
IC3851
BH3547F
1
2
3
4
27
28
26
25
22
24
23
21
6
5
8
7
10
11
12
9
13
14
18
20
15
19
16
17
CONTROL
LOGIC
AVCC
POWER
LIMIT
PWM
LOGIC
DRIVE
GAIN
CONTROL
DRIVE
DRIVE
POWER
LIMIT
PWM
LOGIC
DRIVE
GND
GVDD
NU
PBTL PVCCR
PVCCR
GND
GND
PVCCL
PVCCL
IC3801
TPA3110D2PWPR
220/6.3V
C3853
1000P
C3856
10K
R3856
220/6.3V
C3854
1000P
C3855
10K
R3855
0.1
C3861
47/25V
C3857
100/16V
C3858
OPEN
R3868
1
C3852
15K
R3852
OPEN
R3854
1
C3851
15K
R3851
OPEN
R3853
0.1
C3860
100K
R3866
OPEN
C3862
10K
R3865
2SC4081UBTLQ
Q3861
CPU-RESET-N
BACKLIGHT-SW
J15RESET
100
R3191
MM5Z5V6B
D3111
1000P
C3116
56K
R3182
32
14
IC3009
PST8429UR
CDVDD
GND OUT
0.033
C3113
220
R3178
1
C3106
OPEN
D3108
1K
R3864
10K
R3861
HP-MUTE
OPEN
Q3862
OPEN
R3863
OPEN
R3869
0.22C3801
OPEN
D38011C3820
1000P
C3811
L3801
10uH
OPEN
R3801
OPEN
C3807
0
R3867
OPEN
C3805
1000P
C3812
L3802
10uH
OPEN
R3802
OPEN
D3802
1
C3821
1
C3822
OPEN
D3803
1000P
C3813
L3803
10uH
OPEN
C3806
OPEN
R3803
OPEN
D3804
1000P
C3814
OPEN
R3804
OPEN
C3810
1
C3823
L3804
10uH
0.22C3802
0.22C3803
0.22C3804
10K
R3862
1C3809
2200P
C3871
220
R3871
2200P
C3870
220
R3870
1C3808
1C3819
10K
R3808
1C3816
1C3817
OPENR3807
1
C3815
0R3806
0R3811
1C3992
2SC4081UBTLQ
Q380110K
R3812
10
R3822
0.1
C3859
1.8K
R3816
10K
R3818
10K
R3817
Q3803
2SA1576UBTLQ
2SC4081UBTLQ
Q3802
47K
R3815
10K
R3805
10K
R3995
OPEN
R3813
0.1
C3993
100K
R3819
OPEN
R3814
OPEN
R3809
OPEN
R3810
1
C3825
1000P
C3824
OPEN
C38321C3828
1000P
C3827
OPEN
C3833
100/16V
C3831
100/16V
C3826
100/16V
C3829
OPEN
Q3804
OPEN
R3823
OPEN
C3560
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
TO FUNCTION CBA
UNIT CN4052
CONTINUE
DIGITAL 3
CONTINUE
DIGITAL 4
(LED DRIVE)
TO DIGITAL
MAIN 2
IC3005(2/6)
AUDIO
I/F
TO DIGITAL
MAIN 6
IC3005(6/6)
CONTINUE
DIGITAL 2
4
3
2
1
YCCBBAAZDD
CONTINUE
DIGITAL 2
CONTINUE
DIGITAL 4
DIGITAL MAIN CBA UNIT
CONTINUE
DIGITAL 6
(LED DRIVE)
(HEADPHONE AMP)
(SWITCHING)
CONTINUE
DIGITAL 3
(RESET)
(AUDIO AMP)
(SWITCHING)
(SWITCHING)
(SWITCHING)
CONTINUE
DIGITAL 3
(BUFFER)
Digital Main 5 Schematic Diagram [TYPE B]
PL13.11BSCD5
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-19
27K
R3237
A4
A3
B4
B1
A1
B3
B2
A2
47K
R3214
47K
R3276
47K
R3273
D3057
RB751S-40
82K
R3415
13
1
15
14
16
3
6
5
11
4
7
12
10
89
2
IC3011
BU9883FV-WE2
VCC1
SDA1
WPB
VCC-OUT
SDA0
SCL0
VCC0 VCC3
SCL3
SDA3
GND
NU
SDA2
SCL2
VCC2
SCL1
F13HPD-SINK
C15SDA-SINK
C16SCL-SINK
4.7K
R3487
0.1
C3191
4.7K
R3488
G3HDMI-SEL0
F1HDMI-SEL1
3.9K
R3486
4.7K
R3497
0.1C3192
100
R3281
100
R3282
4.7K
R3496
100
R3405
10K
R3489
0.1
C3005
1K
R3018
B5PLL-XFC-A
A5PLL-XFC-P
C4EXT-RES
2.2
C3187
4700P
C3186
3K
R3271
2200P
C3188
10K
R3452
10K
R3451
R3055
1K
0.1
C3023
1K
R3063
D3003
RB751S-40
D3001
RB751S-40
D3002
RB751S-40
22K
R3023
1K
R3029
M12PWR
10K
R3022
0.1
C3018
47K
R3212
HDMI-CEC B15
IC3005(6/6)
R8A05011BG-U0
*1
HDMI SW
IC3018
TMDS351PAGR
123
GND
4
56
VCC
789
GND
10
1112
VCC
131415
GND
16
NU
21
22 GND
23
24
25 VCC
26
27
28 GND
29 SCL-SINK
30 SDA-SINK
31
HOT-PLUGDETECT-SINK
32
HDMISEL0
33
HDMI-
SEL1
34NU35
HOT-PLUG-
DETECT1
36 37 38
39 40
VCC
41 42 43
GND
44 45 46
VCC
47 48
49NU
50
HOT-PLUGDETECT2
51
52
53
54
55VCC
56
57
58GND
59
60
61VCC
62
63
64
HOT-PLUGDETECT3
20
19 VCC
18
17
R3066
2.7K
R3058
10K
R3010
1K
R3017
10K
R3019
2.7K
R3025
1K
R3027
10K
R3040
2.7K
16 HDMI-DATA
14 NU
17 GND
13 HDMI-CEC
15 HDMI-CLOCK
16 HDMI-DATA
14 NU
17 GND
13 HDMI-CEC
15 HDMI-CLOCK
14 NU
9 TMDS-D0(-)
10 TMDS-CLOCK(+)
3 TMDS-D2(-)
17 GND
11 C-SHIELD0
7 TMDS-D0(+)
2 D-SHIELD0
JK3004
1 TMDS-D2(+)
13 HDMI-CEC
8 D-SHIELD2
4 TMDS-D1(+)
6 TMDS-D1(-)
5 D-SHIELD1
12 TMDS-CLOCK(-)
15 HDMI-CLOCK
16 HDMI-DATA
18 +5V
19 HOT PLUG DETECT
18 +5V
19 HOT PLUG DETECT
19 HOT PLUG DETECT
18 +5V
12 TMDS-CLOCK(-)
4 TMDS-D1(+)
8 D-SHIELD2
11 C-SHIELD0
2 D-SHIELD0
3 TMDS-D2(-)
10 TMDS-CLOCK(+)
7 TMDS-D0(+)
6 TMDS-D1(-)
JK3003
1 TMDS-D2(+)
9 TMDS-D0(-)
5 D-SHIELD1
10 TMDS-CLOCK(+)
JK3002
1 TMDS-D2(+)
8 D-SHIELD2
4 TMDS-D1(+)
3 TMDS-D2(-)
5 D-SHIELD1
12 TMDS-CLOCK(-)
7 TMDS-D0(+)
9 TMDS-D0(-)
2 D-SHIELD0
6 TMDS-D1(-)
11 C-SHIELD0
P-ON+3.3V
AL+3.3V
VGA-SCL
VGA-SDA
Q3014
2SK3018
2SC4081UBTLQ
Q3001
2SC4081UBTLQ
Q3002
2SC4081UBTLQ
Q3008
Q3451
2SC4081UBTLQ
100
R3514
47K
R3278
OPEN
C3203
OPEN
C3202
OPEN
C3204
OPEN
C3205
0
R3992
10K
R3024
OPEN
C3207
OPEN
C3206
OPEN
C3208
1.5K
R3453
22
R3508
22
R3509
2.2K
R3270
1P
C3990
OPEN
C3985
OPEN
C3984
OPEN
C3987
OPEN
C3986
OPEN
C3989
OPEN
C3988
10K
R3991
OPEN
R3990
G14HDMI-SCL
F14HDMI-SDA
4.7K
R3192
4.7K
R3193
P-ON+5V
P-ON+3.3V(1)
560
R3236
0.01
C3185
OPEN
C3424
OPEN
C3427
10
C3316
OPEN
C3422
1
C3426
OPEN
C3420
1
C3423
1
C3425
1
C3421
D3993
OPEN
PWR
HPD-SINK
OPEN
R3994
0
R3081
0
R3076
0
R3075
0
R3074
0
R3073
OPEN
R3080
OPEN
R3078
47K
R3275
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
3
2
1
4
EE FF GG HH II JJ
CONTINUE
DIGITAL 4
(BUFFER)
HDMI
I/F
VIDEO
DECODER
TO DIGITAL
MAIN 5
IC3005(5/6)
TO DIGITAL
MAIN 2
IC3005(2/6)
AUDIO
DECODER
(HDMI SW)
DIGITAL MAIN CBA UNIT
HDMICONNECTOR-3
(HDMI SERIAL EEPROM)
HDMICONNECTOR-1
CONTINUE
DIGITAL 2
(SWITCHING)
(SWITCHING)
(SWITCHING)
HDMICONNECTOR-2
CONTINUE
DIGITAL 5
(SWITCHING)
Digital Main 6 Schematic Diagram [TYPE B]
PL13.11BSCD6
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-20
12K
R3045
11K
R3044
3.9K
R3047
12K
R3046
47/25V
C3057
P-ON+21V
VCOM-PWM
P-ON+3.3V
CELL-PWR-CTRL
0.1
C3058
1
2
3
45
6
7
8
IC3201
OPEN
SS
EN
COMP
FB GND
SW
IN
BST
OPEN
C3202
D3203
OPEN OPEN
C3213
OPEN
C3210
OPEN
C3211
OPEN
R3218
OPEN
C3205
OPEN
C3212
OPEN
R3216
L3201
OPEN
OPEN
C3208
OPEN
C3209
OPEN
C3207
OPEN
C3214
OPEN
C3201
OPEN
R3213
OPEN
C3204
OPEN
R3208
OPEN
R3209
OPEN
R3205
OPEN
D3201
OPEN
R3211
D3202
OPEN
PROTECT3
OPEN
D3204
OPEN
C3000
1K
R3048
3NU
48 LCD+21V
11 NU
12 NU
6 GND
9NU
5NU
50 LCD+21V
47 GND
7 GND
49 LCD+21V
8 GND
CN3013
1NU
10 NU
43 P-ON+3.3V
4NU
42 GND
2NU
41 GND
44 P-ON+3.3V
45 VCOMA
51 GND
46 DCDC-EN
0R3165
OPEN
R3130
0
R3171
0R3170
1000P
C3167
4.7
C3166
0R3166
0R3167
4NU
2 GND
CN3005
1 GND
3NU
0R3173
OPEN
C3171
OPEN
C3170
OPEN
R3172
OPEN
R3129
0
R3099
0R3253
0R3254
0R3251
0R3252
0
R3168
0
R3169
0R3174
OPEN
C3203
OPEN
R3202
OPEN
C3235
OPEN
C3206
OPEN
R3215
OPEN
R3291
0
R3217
OPEN
R3289
Q3282
OPEN
1
2
36
7
8
45
OPEN
C3282
OPEN
R3283
OPEN
C3258
OPEN
C3257
Q3201
OPEN
G
SD
OPEN
R3085
116
118
103
113
107
119
99
121
100
114
112
117
97
104
105
120
115
101
122
123
102
106
108
3PC3682
3PC3674
3PC3662
3PC3661
3PC3666
OPENC3671
3PC3667
3PC3670
OPENC3672
3PC3677
OPENC3683
3PC3668
OPENC3684
3PC3676
3PC3664
3PC3669
3PC3673
3PC3681
3PC3663
3PC3665
3PC3679
3PC3675
3PC3680
3PC3678
OPENR3145
OPENR3143
OPENR3142
OPENR3141
OPENR3140
OPENR3139
OPENR3137
OPENR3111
OPENR3110
OPENR3109
OPENR3248
OPENR3249
OPENR3149
OPENR3153
P-ON+5V
OPEN
R3284
OPEN
Q3202
OPEN
R3282
OPEN
C3256
OPEN
R3281
OPEN
Q3281
OPEN
C3281
OPEN
R3288
OPEN
R3287
OPEN
R3286
P-ON-H2
LVDS-OD0(+)
LVDS-OD3(+)
LVDS-OD2(-)
LVDS-OD3(-)
LVDS-OD1(-)
LVDS-OD0(-)
LVDS-OD2(+)
LVDS-OCLK(+)
LVDS-OD1(+)
LVDS-OCLK(-)
98
*1
IC3001(1/5)
MSD8200DS-S1
PANEL-VCOM-PWM
CELL-PWR-CTRL
LCD+12V
16 LVDS-OCLK(+)
30 LVDS-ED3(-)
29 LVDS-ED3(+)
39 LVDS-ED0(+)
33 LVDS-ECLK(-)
35 LVDS-ED2(+)
19 LVDS-OD2(+)
15 GND
37 LVDS-ED1(+)
34 GND
32 LVDS-ECLK(+)
25 GND
26 GND
27 NU
28 NU
24 LVDS-OD0(-)
38 LVDS-ED1(-)
18 GND
22 LVDS-OD1(-)
40 LVDS-ED0(-)
21 LVDS-OD1(+)
31 GND
14 LVDS-OD3(-)
23 LVDS-OD0(+)
36 LVDS-ED2(-)
20 LVDS-OD2(-)
17 LVDS-OCLK(-)
13 LVDS-OD3(+)
2SC4081UBTLQ
Q3007
DIGITAL MAIN CBA UNIT
CONTINUE
DIGITAL 3
(NO CONNECTION)
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
TO DIGITAL
MAIN 4
IC3001(3/5)
LVDS
TX
TO LCD PANEL
ASSEMBLY
CONTINUE
DIGITAL 5
CONTINUE
DIGITAL 2
A
2
4
1
3
BCDEF
CONTINUE
DIGITAL 2
(SWITCHING)
Digital Main 1 Schematic Diagram [TYPE C]
PL13.11CSCD1
The order of pins shown in this diagram is different from that of actual IC3001.
IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-21
LVDS-OCLK(-)
LVDS-OD0(+)
LVDS-OD3(+)
LVDS-OD2(-)
LVDS-OD0(-)
LVDS-OD2(+)
LVDS-OD1(+)
LVDS-OCLK(+)
LVDS-OD3(-)
LVDS-OD1(-)
OPEN
R3931
OPEN
R3932
OPEN
R3933
OPEN
R3934
OPEN
R3935
4 CPV
17 GND
11 LLV4(+)
8 LLV5(-)
28 GND
26 PWR-CTRL
12 LLV3(-)
1 STV
10 LLV4(-)
13 LLV3(+)
22 LLV0(-)
29 LCD+12V
2 OE2
23 LLV0(+)
16 LLVCNK(+)
21 LLV1(+)
15 LLVCLK(-)
30 LCD+12V
CN3001
31 LCD+12V
20 LLV1(-)
18 LLV2(-)
19 LLV2(+)
3 OE1
9 LLV5(+)
24 GND
5 POL
6TP
14 GND
7 GND
25 P-ON+3.3V
27 VCOM-PWM
14 GND
10 LLV4(-)
17 GND
22 LLV0(-)
20 LLV1(-)
13 LLV3(+)
7 GND
21 LLV1(+)
19 LLV2(+)
5 POL
4 CPV
18 LLV2(-)
23 LLV0(+)
9 LLV5(+)
12 LLV3(-)
29 LCD+12V
15 LLVCLK(-)
16 LLVCNK(+)
2 OE2
3 OE1
28 GND
11 LLV4(+)
26 PWR-CTRL
8 LLV5(-)
1 STV
24 GND
27 VCOM-PWM
25 P-ON+3.3V
6TP
CN3006
30 LCD+12V
LCD+12V
OPEN
C3513
OPEN
C3514
OPENR3037
OPENR3038
OPEN
R3035
CELL-PWR-CTRL
PANEL-VCOM-PWM
OPEN
R3039
OPEN
C3512
OPENR3910
OPENR3908
OPENR3911
OPENR3914
OPENR3912
OPENR3909
OPENR3117
OPENC3161
OPENC3162
OPENC3163
OPENC3164
OPENC3102
OPENC3165
OPENR3118
OPENR3119
OPENR3120
OPENR3132
OPENR3041
OPEN
R3904
OPEN
C3902
OPEN
R3906
OPEN
R3926
OPEN
C3923
OPEN
C3924
OPEN
C3919
OPEN
C3921
OPEN
C3916
OPEN
C3918
OPEN
C3914
OPEN
C3915
OPEN
R3927
OPEN
R3925
OPEN
R3921
OPEN
R3922
OPEN
R3928
OPEN
C3920
VDDC+1.26V
L3901
OPEN
C3913
OPEN
OPEN
R3924
OPEN
R3923
OPEN
R3913
OPEN
R3907
OPEN
C3922
OPEN
C3925
BACKLIGHT-DIM
BACKLIGHT-ADJ
OPEN
R3916
OPEN
OPEN
R3919
D3905
OPEN
OPEN
R3920
OPEN
C3917
OPEN
R3917
OPEN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
21 22 24 25 26 27 28 2923 30 31 32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49505152535455565758596061626364
20191817
DATA
INPUT
LATCH
LVDS
OUTPUT
DATA
PROCESSING
LVDS
RX
CONTROL SIGNAL GENERATOR
SERIAL
I/F
IC3902
OPEN
VDD-LVDS
GND
VDDC(1.2V)
RESET
GND
LV-SEL
PWMO/GP06
VDDC(1.2V)NUNU
VDDP(3.3V)NUNU
UD-SEL/GP02
KB/GP01
VDDP(3.3V)
GND
GND
VDDP(3.3V)
REL
VDDP(3.3V)
NU
NU
GND
GND
VDDC(1.2V)
MGD-EN
/GP08
VDDP
(3.3V)
NU
OD-EN/GP08
VDDP(3.3V)
TSET
P-ON+3.3V
OPEN
R3028
4
1
3
2
JILGH K
DIGITAL MAIN CBA UNIT
CONTINUE
DIGITAL 1
(NO CONNECTION)
(NO CONNECTION)
CONTINUE
DIGITAL 5
CONTINUE
DIGITAL 5
CONTINUE
DIGITAL 1
Digital Main 2 Schematic Diagram [TYPE C]
PL13.11CSCD2
10-22
IC3002
K4T51163QJ-BCE7
*A VDD
J2VREF
E2 NU
K2CKE
J8CK
K8CK
L8CS
K7RAS
L7CAS
K3WE
L1BA2/NU
L3BA1
L2BA0
R2A12
P7A11
M2A10/AP
P3A9
P8A8
P2A7
N7A6
N3A5
N8A4
N2A3
M7A2
M3A1
M8A0
K9ODT
*BVSS
A2 NU
R8A13
R7 NU
R3 NU
B7 UDQS
A8 UDQS/NU
B3 UDM
B9 MDQU7
C2 MDQU1
C8 MDQU0
F7 LDQS
E8 LDQS/NU
F3 LDM
F9 MDQL7
F1 MDQL6
H9 MDQL5
H1 MDQL4
H3 MDQL3
H7 MDQL2
G2 MDQL1
G8 MDQL0
0.1
C3222
1
2
3
45
6
7
8
IC3006
W25Q32FVSSIG
CS
SO
WP
GND SDA
SCL
NU
VCC
0.1C3223
0.1C3224
0.1C3225
0.1C3226
0.1C3227
0.1C3228
0.1C3229
0.1C3218
0.1C3216
0.1C3220
0.1C3221
0.1C3215
4.7K
R3102
0.1
C3073
P-ON+3.3V
AL+3.3V
DDR+1.8V
10C3219
D1 MDQU4
D3 MDQU3
D7 MDQU2
B1 MDQU6
D9 MDQU5
1K
R3232
1K
R3231
OPENC3230
OPENC3231
OPENC3232
OPENC3233
OPENC3234
190 SD-A3
174 SD-A4
187 SD-A9
192 SD-CKE
176 SD-A8
169 SD-RAS
183 SD-A10
172 SD-A2
168 SD-ODT
170 SD-CAS
171 SD-A0
181 SD-BA0
188 SD-A12
179 SD-WE
191 SD-BA2
175 SD-A6
165 SD-CLKN
184 SD-A5
180 SD-BA1
182 SD-A1
202 WP
177 SD-A11
164 SD-CLK
189 SD-A7
145 SD-UDM
161 MDQL2
144 MDQU6
139 MDQL6
138 MDQL1
152 SD-LDM
143 MDQU1
154 MDQU0
142 MDQU4
153
MSD8200DS-S1
*1
IC3001(2/5)
MDQU7
162 MDQL5
150 SD-UDQSN
158 MDQL7
136 MDQL4
149 SD-UDQS
157 MDQU5
155 MDQU2
148 SD-LDQSN
160 MDQL0
137 MDQL3
141 MDQU3
147 SD-LDQS
204 CS
199 SPI-SCL
201 SOUT
200 SPI-SDA
75R3238
75R3221
75R3229
75R3237
75R3222
75R3235
75R3236
75R3227
75R3204
75R3203
75R3223
75R3240
75R3224
75R3225
75R3239
75R3226
56
R323456R3233
0.01
C3217
R3220 75x4
R3228 75x4
178 SD-A13
75R3230
33R3089
33R3154
33R3092
OPEN
R3194
10K
R3107
33R3093
33R3094
0.033
C3113
OPEN
D3108
1000P
C3116
220
R3178
56K
R3182
1
C3106
RESET
32
14
IC3009
PST8429UR
CDVDD
GND OUT
OPEN
C3252
OPEN
D3110
2SC4081UBTLQ
Q3104100
R3241
10K
R3219
OPEN
D3109
OPEN
R3242
216 STB-RESET
OPEN
C3110
VCOM-PWM
CELL-PWR-CTRL
OPEN
C3175
OPEN
R3150132I2S-OUT-MCK
OPEN
R3195
1K
R3199
75BACKLIGHT-SW
OPEN
R3210
22R3106
129BACKLIGHT-ADJ
OPEN
Q3101
PROTECT1
206P-ON-H2
10R3101
10K
R3191
PROTECT3
134PROTECT3
BACKLIGHT-ADJ
OPEN
R3177
100
R3161
10K
R3196
209PROTECT1
10K
R3193
P-ON-H2
2SA1576UBTLQ
Q3103
BACKLIGHT-SW
33K
R3189
10K
R3160
10K
R3159
OPEN
Q3102
OPEN
R3156
76CELL-PWR-CTRL
OPEN
R3155
83VCOM-PWM
100
R3188
10K
R3163
X3101
24MHz
15P
C3169
18P
C3172
L3101
22uH
0.1C3121
51AUVRM
53AUVAG
52AUVRP
1C3133
10C3120
4.7C3123
66XOUT
67XIN
160
R3157
OPEN
R3158
BACKLIGHT-SW
AMP-MUTE127AMP-MUTE
OPEN
R3355
OPEN
C3189
207NU
1C3101
100R3162
33K
R3197
P-ON-H2
PROTECT3
DIGITAL MAIN CBA UNIT
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
(DDR2 SDRAM)
*B:A3,A7,B2,B8,D2,D8,E3,E7,
F2,F8,H2,H8,J3,J7,N1,P9
*A:A1,A9,C1,C3,C7,C9,E1,E9,
G1,G3,G7,G9,J1,J9,M9,R1
1-O3
2-O3
3-O3
4-O3
5-O3
6-O3
MDQU7
MDQU1
MDQU0
MDQL7
1-M3
2-M3
3-M3
4-M3
5-M3
6-M3
(MEMORY)
CONTINUE
DIGITAL 5
2
MP
1
NO
3
4
QR
TO DIGITAL
MAIN 4
IC3001(3/5)
MDQU3
MDQU2
MDQU6
MDQU5
MDQU4
MDQL6
MDQL5
MDQL4
MDQL3
MDQL2
MDQL1
MDQL0
MDQU7
MDQU1
MDQU0
MDQU3
MDQU2
MDQU6
MDQU5
MDQU4
MDQL7
MDQL6
MDQL5
MDQL4
MDQL3
MDQL2
MDQL1
MDQL0
(RESET)
(SWITCHING)
CONTINUE
DIGITAL 1
TO DIGITAL
MAIN 4
IC3001(3/5)
CONTINUE
DIGITAL 5
CONTINUE
DIGITAL 4
(SWITCHING)
The order of pins shown in this diagram is different from that of actual IC3001.
IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section.
1 NOTE:
Digital Main 3 Schematic Diagram [TYPE C]
PL13.11CSCD3
10-23
SP3801
SPEAKER
L-CH
3 SP(R)-
2 SP(L)-
4 SP(R)+
CN3801
1 SP(L)+
AMP-MUTE
AL+3.3V
P-ON+5V
AMP+13V
HEADPHONE
JACK
JK3703
P-ON+3.3V
1
2
3
4
27
28
26
25
22
24
23
21
6
5
8
7
10
11
12
9
13
14
18
20
15
19
16
17
CONTROL
LOGIC
AVCC
POWER
LIMIT
PWM
LOGIC
DRIVE
GAIN
CONTROL
DRIVE
DRIVE
POWER
LIMIT
PWM
LOGIC
DRIVE
GND
GVDD
NU
PBTL PVCCR
PVCCR
GND
GND
PVCCL
PVCCL
IC3801
TPA3110D2PWPR
1K
R3704
1
C3704
BACKLIGHT-SW
0.22C3801
OPEN
D3801
OPEN
C3820
1000P
C3811
L3801
10uH
OPEN
R3801
OPEN
C3807
OPEN
C3808
1000P
C3812
L3802
10uH
OPEN
R3802
OPEN
D3802
1
C3821
OPEN
C3822
OPEN
D3803
1000P
C3813
L3803
10uH
OPEN
C3809
OPEN
R3803
OPEN
D3804
1000P
C3814
OPEN
R3804
OPEN
C3810
1
C3823
L3804
10uH
0.22C3802
0.22C3803
0.22C38041C3806
1C3805
1C3819
10K
R3808
1C3816
1C3817
OPENR3807
0R3806
OPENR3805
1C3818
2SC4081UBTLQ
Q380110K
R3812
10
R3820
OPEN
R3818
10K
R3814
Q3803
OPEN
OPEN
Q3802
OPEN
R3817
OPEN
R3816
10K
R3811
OPEN
R3821
0
R3813
10K
R3809
OPEN
R3810
10
C3832
0.047
C3827
2.2
C3828
220/16V
C3831
100/16V
C3829
SP3802
SPEAKER
R-CH
OPEN
C38361C3837
OPEN
C3838
OPEN
C3839
OPEN
C38411C3842
OPEN
C3843
OPEN
C3844
10
C3833
0.047
C3824
2.2
C3825
D3806
1SS400
D3805
1SS400
10K
R3705
1
C3815
100K
R3815
OPEN
R3819
0.1
C3830
OPEN
R3725
220/6.3V
C3705
OPEN
R3718
OPEN
R3701
OPEN
C3711
OPEN
R3716
0.01
C3721
L3701
10uH
OPEN
D3702
OPEN
D3707
OPEN
D3706
OPEN
D3701
1K
R3702
L3702
10uH
0.01
C3722
OPEN
C3712
OPEN
R3719
OPEN
R3724
OPEN
R3717
OPEN
R3703
220/6.3V
C3710
OPEN
D3703
OPEN
D3708
OPEN
Q3703
OPEN
R3722
OPEN
R3723
OPEN
R3721
OPEN
R3720
OPEN
Q3702
OPEN
C3723
OPEN
C3724
D3704
OPEN
OPEN
R3726
75
R3126
R3136 33
10K
R3712
220
R3709
10P
C3701
10P
C3702
330P
C3720
R3123 0
D3302 1SS400
12K
R3713
1
2
3
4514
13
12
11156
7
8
9
10
JK3001
PC-RGB-IN
75
R3146
100
R3708
100P
C3709
JK3702
4.7KR3326
2.2C3126
75
R3148
1
C3707
100P
C3188
R3144 33
4.7KR3321
0.1
C3708
75
R3147
2.2C3125
7.5K
R3711
330P
C3719
10P
C3703
2SC4081UBTLQ
Q3701
R3122 33
1
C3706
75
R3127
JK3701
75
R3125
D3301
1SS400
100
R3710
OPENC3015
10PC3009
D3055 OPEN
D3045 OPEN
D3050 OPEN
D3053 OPEN
D3049 OPEN
0.047C3118
0.047C3139
0.047C3136
1000PC3119
10PC3007
OPENC3016
R3131 0 1000PC3137
28
10PC3002
OPENC3017
27
0
R3016
OPEN
C3018
30
0.047C3117R3121 68
31
0.047C3134R3134 33
10KR3347
R3339 100
26 VGA-HSYNC
10KR3358
R3343 100
10PC3020
OPENC3014
32 VGA-VSYNC
D3054 OPEN
D3041 OPEN
38
35
34
0.047C314033R3138
36
COMP-DET133
IC3001(3/5)
*1
MSD8200DS-S1
NU37
68R3124 0.047C3141
0
R3715
OPEN
C3715
OPEN
C3716
R3198 100
130
SPDIF
10K
R3706
560P
C3718
47
560P
C3713
10K
R3707
12K
R3714
48
OPEN
C3714
OPEN
C3717
61
60
220KR3164
330PC3147
220KR3175
330PC3148
63
64
10K
R3200
1
2
34
5
IC3019
AP2151WG-7
OUT
GND
/FLAG RN
IN
80VBUS-ST
10K
R3479
1
C3327
22R3176
82VBUS-EN
2 USB(-)
4 GND
3 USB(+)
CN3009 (USB JACK)
1 BUS-POWER
220/6.3V
C33481C3246
OPEN
D3052
195USB(+)
5.1R3020
5.1R3021
194USB(-)
2UART0-TX
CN3010
1P-ON+5V
3UART0-RX
4GND
OPEN
C3254
OPEN
C3255
OPEN
R3395
OPEN
R3396
OPENC3013
10PC3019
OPEN
R3015
OPEN
R3014
OPEN
C3253
213 VGA-SDA
212 VGA-SCL
47R3114
47R3115
UARTTXD0
UARTRXD0
0.047C312468R3128
NU45
10K
R3480
R3354 33
0.047C3135
29
R3135 33
DIGITAL MAIN CBA UNIT
(AUDIO AMP)
(SWITCHING)
WX
2
4
1
VS
3
TU
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
DIGITAL
AUDIO OUT
(COAXIAL)
AUDIO(R)-IN
SW
COMPONENT
-Pr-IN
AUDIO
I/F
TO DIGITAL
MAIN 6
IC3001(5/5)
AUDIO(L)-IN
(BUFFER)
COMPONENT
-Pb-IN
COMPONENT-Y
/VIDEO-IN
DIGITAL
SIGNAL
PROCESS
TO DIGITAL
MAIN 1
IC3001(1/5)
A/D
CONVERTER
(HIGH SIDE SW)
(NO CONNECTION)
TO DIGITAL
MAIN 6
IC3001(5/5)
TO DIGITAL
MAIN 6
IC3001(5/5)
TO DIGITAL
MAIN 6
IC3001(5/5)
TO DIGITAL
MAIN 3
IC3001(2/5)
TO DIGITAL
MAIN 3
IC3001(2/5)
CONTINUE
DIGITAL 5
CONTINUE
DIGITAL 6
CONTINUE
DIGITAL 3
The order of pins shown in this diagram is different from that of actual IC3001.
IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section.
1 NOTE:
Digital Main 4 Schematic Diagram [TYPE C]
PL13.11CSCD4
10-24
6P-ON-H2
CN3601
1LED-CONT(NU)
17AMP+13V
2PROTECT1
10GND
7BACKLIGHT-ADJ
11GND
15AMP+13V
14GND
21P-ON+21V
8AL+3.3V
22P-ON+21V
18AMP+13V
3PROTECT3
13GND
4RESET
23P-ON+21V
9GND
16AMP+13V
20P-ON+21V
12GND
5BACKLIGHT-SW
19GND
19BACKLIGHT-SW
21PROTECT3
8AMP+13V
2P-ON+21V
14GND
22PROTECT1
1P-ON+21V
4P-ON+21V
9AMP+13V
20RESET
3P-ON+21V
18P-ON-H2
12GND
CN3602
23LED-CONT(NU)
15GND
13GND
11GND
7AMP+13V
5GND
17BACKLIGHT-ADJ
10GND
16AL+3.3V
6AMP+13V
P-ON+5V
P-ON+3.3V
P-ON21V
10
C3623
1
2
3
45
6
7
8
IC3604
RT8293ALZSP
BS
VIN
SW
GND FB
COMP
EN
SS
OPEN
R3628
L3602
10uH
0.1
C3618
OPEN
C3616
0.22
C3617
5.1K
R3603
C3621
10
OPEN
C3643
C3620
220/6.3V
0.1
C3652
OPEN
C3638
20K
R3615
4700P
C3619
0.01
C3615
10K
R3614
33K
R3616
D3608
OPEN
Q3601
2SC4081UBTLQ
20K
R3621
1K
R3620
OPEN
C3641
D3609
1SS400
OPEN
C3656
0.1
C3655
OPEN
C3657
2SA1576UBTLQ
Q3005
22K
R3008
Q3006
2SC4081UBTLQ
1
C3011
100K
R3005
56K
R3097
D3012
1SS400
OPEN
R3100
100K
R3007
10K
R3098
OPEN
C3010
47K
R3618
D3011
MM5Z7V5B
OPEN
R3133
OPEN
C3630
1
2
3
45
6
7
8
IC3605
RT8293ALZSP
BS
VIN
SW
GND FB
COMP
EN
SS
C3635
10
2K
R3619
100
R3647
OPEN
R3627
10K
R3641
10
C3622
1
C3633
0.01
C3629
8.2K
R3625
0.1
C3601
L3603
10uH
0.01
C3626
10
C3634
1K
R3626
4.7
C3637
OPEN
C3642
Q3603
2SC4081UBTLQ
2SA1576UBTLQ
Q3602
0.1
C3628
100
R3642
0.047
C3627
16K
R3624
D3606
PTZTE255.1B
10K
R3644
C3632
220/6.3V
OPEN
C3686
47K
R3643
10K
R3645
1
2
3
45
6
7
8
IC3603
BD00IA5WEFJ-E2
VOUT
FB
GND
NU EN
NU
NU
VCC
10
C3610
11K
R3613
2.2K
R3611
12K
R3612
10
C3613
OPEN
R3646
OPEN
C3687
1
R3661
10K
R3601
10
C3608
100
R3606
220/6.3V
C3605
10
C3614
220
R3604
123
IC3602
AP1117EG-13
VOUT
VIN
COM
33
R3605
10
C3612
220/6.3V
C3602
0
R3608
123
IC3601
AP1117EG-13
VOUT
VIN
COM
120
R3609
120
R3610
180
R3607
D3603
1SS400
D3601
1SS400
10
C3636
OPEN
R3623
22K
R3656
22K
R3651
2SC4081UBTLQ
Q3606
2SA1576UBTLQ
Q3605
10K
R3655
10
R3654
10K
R3652
1K
R3653
OPEN
R3638
OPEN
C3604
OPEN
C3647
OPEN
C3646
OPEN
C3645
0.1
C3648
OPEN
C3649
OPEN
C3603
10
C3660
D3602
OPEN OPEN
C3644
OPEN
C3640
OPEN
C3624
OPEN
C3625
4.7
C3639
4.7
C3607
D3610
MM5Z4V3B1
C3659 D3611
OPENOPEN
C3658
12 AVDD-DVI
90 AVDD-DVI-PC
203 AVDD-ALIVE
L3110
OPEN
10
C3103
0.1
C3132
0.1
C3160
0.1
C3114
40 AVDD-CVBS
0.1
C3130
0.1
C3158
L3112
OPEN
59 AVDD-AU33
0.1
C3159
L3114
OPEN
68 AVDD-DMPLL
0.1
C3157
L3113
OPEN
65 AVDD-EAR33
25 VDDC
0.1
C3127
33 AVDDL-ADC
0.1
C3131
84 VDDC
0.1
C3151
111 AVDDL-MOD
0.1
C3185
124 VDDC
0.1
C3176
156 DVDD-DDR
0.1
C3186
193 VDDC
0.1
C3107
39 AVDD-ADC25
0.1
C3129
0.1
C3128
L3103
22uH
54 AVDD-AU25
L3102
22uH
0.1
C3154
L3107
22uH
69 AVDD-ADC25
L3105
22uH
72 AVDD-PGA25
0.1
C3152
73 PGA-COM
L3106
22uH
0.1
C3184
110 AVDD-MOD
81 VDDP
10
C3155
0.1
C3156
L3116
OPEN
109 AVDD-LPLL
0.1
C3181
128 VDDP
0.1
C318310C3182
L3115
OPEN
166 AVDD-PLL
0.1
C3112
140
MSD8200DS-S1
*1
IC3001(4/5)
AVDD-DDR-DATA
0.1
C3180
0.1
C3178
0.1
C3179
0.1
C3108
0.1
C3177
146 AVDD-DDR-DATA
151 AVDD-DDR-DATA
0.1
C3111
0.1
C3109
159 AVDD-DDR-DATA
163 AVDD-DDR-DATA
173 AVDD-DDR-CMD
186 AVDD-DDR-CMD
C3611
220/6.3V
AL+3.3V(1)
62 GND
77 GND
198 GND
L3111
OPEN
L3109
22uH
P-ON+5V
P-ON+3.3V
AL+3.3V
AMP+13V
P-ON+5V
AL+3.3V
P-ON+3.3V
OPEN
C3651
VDDC+1.26V
P-ON+3.3V
DDR+1.8V
P-ON+3.3V
AL+3.3V
PROTECT3
RESET
BACKLIGHT-ADJ
PROTECT1
BACKLIGHT-ADJ
BACKLIGHT-SW
BACKLIGHT-DIM
P-ON-H2
100R3633
100R3631
100R3632
OPENR3629
OPEN
C3650D3607
OPEN
OPEN
R3637
270R3635
OPEN
C3653
10
C3609
1
R3662
57NU
58NU
167NU
185NU
196NU
197NU
43NU
44NU
46NU
55NU
50NU
42NU
56NU
49NU
41NU
2K
R3108
DIGITAL MAIN CBA UNIT
TO POWER SUPPLY
CBA CN501
(NO CONNECTION)
(+5V REG.)
(SWITCHING)
(SWITCHING)
(SWITCHING)
(+1.26V REG.)
(+1.8V REG.)
(+3.3V REG.)
(+2.5V REG.)
(SWITCHING)
Z
4
AA ADACABY
2
1
3
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
CONTINUE
DIGITAL 1
CONTINUE
DIGITAL 6
CONTINUE
DIGITAL 4
CONTINUE
DIGITAL 2
CONTINUE
DIGITAL 3
CONTINUE
DIGITAL 3
CONTINUE
DIGITAL 2
(SWITCHING)
(SWITCHING)
(SWITCHING)
The order of pins shown in this diagram is different from that of actual IC3001.
IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section.
1 NOTE:
Digital Main 5 Schematic Diagram [TYPE C]
PL13.11CSCD5
10-25
10K
R3275
10K
R3278
10K
R3212
10K
R3214
10K
R3001
10K
R3003
16 HDMI-DATA
12 CLOCK(-)
JK3004
1 DATA2(+)
6 DATA1(-)
3 DATA2(-)
14 ARC
9 DATA0(-)
10 CLOCK(+)
7 DATA0(+)
5 TMDS DATA1 SHIELD
17 GND
18 +5V
13 HDMI-CEC
15 HDMI-CLOCK
19 HOT PLUG DETECT
2 TMDS DATA2 SHIELD
4 DATA1(+)
11 TMDS CLOCK SHIELD
8 TMDS DATA0 SHIELD
16 HDMI-DATA
12 CLOCK(-)
JK3003
1 DATA2(+)
6 DATA1(-)
3 DATA2(-)
14 NU
9 DATA0(-)
10 CLOCK(+)
7 DATA0(+)
5 TMDS DATA1 SHIELD
17 GND
18 +5V
13 HDMI-CEC
15 HDMI-CLOCK
19 HOT PLUG DETECT
2 TMDS DATA2 SHIELD
4 DATA1(+)
11 TMDS CLOCK SHIELD
8 TMDS DATA0 SHIELD
14 NU
17 GND
19 HOT-PLUG-DETECT
15 HDMI-CLOCK
18 HDMI+5V
16 HDMI-DATA
2 TMDS DATA2 SHIELD
10 CLOCK(+)
JK3002
1 DATA2(+)
4 DATA1(+)
7 DATA0(+)
5 TMDS DATA1 SHIELD
8 TMDS DATA0 SHIELD
11 TMDS CLOCK SHIELD
3 DATA2(-)
13 HDMI-CEC
6 DATA1(-)
12 CLOCK(-)
9 DATA0(-)
2SC4081UBTLQ
Q34071K
R3421
1K
R3420
OPEN
R3423
47K
R3422
1K
R3010
OPEN
R3017
2SC4081UBTLQ
Q30011K
R3018
47K
R3019
OPEN
R3058
1K
R3055
2SC4081UBTLQ
Q30081K
R3063
47K
R3066
2SC4081UBTLQ
Q300210K
R3071
33K
R3076
2SA1576UBTLQ
Q3004
OPEN
R3077
10K
R3079
100R3407
100R3406
100R3042
100R3050
100R3022
100R3023
100R3113
P-ON+5V
P-ON+3.3V
AL+3.3V
22
21
19
18
16
15
14
13
11
3
10
4
2
5
7
8
95
86
91
94
87
89
88
92
85HDMI3-HPD
96
20
23
6
214HDMI-CEC
93
1HDMI2-HPD
17HDMI1-HPD
9
OPENR3425
OPENR3426
OPENR3427
OPENR3428
OPENR3429
OPENR3430
OPENR3431
OPENR3432
0.1
C3404
D3004
RB751S-40
D3005
RB751S-40
OPENR3057
OPENR3062
OPENR3064
OPENR3065
OPENR3056
OPENR3067
OPENR3069
OPENR3070
0.1
C3005
D3006
RB751S-40
D3007
RB751S-40
OPENR3026
OPENR3027
OPENR3036
OPENR3029
OPENR3034
OPENR3024
OPENR3025
OPENR3040
0.1
C3023
D3008
RB751S-40
D3009
RB751S-40
2SC4081UBTLQ
Q3011
100
R3081
1K
R3078
2SC4081UBTLQ
Q3003
33K
R3074
10K
R3073
330P
C3003
1K
R3075
10K
R3080
OPEN
R3243
OPEN
R3244
OPEN
R3245
OPEN
C3556
OPEN
C3557
22
R3105
4KEY-IN1
33PC3551
OPEN
R3558
100
R3552
39K
R3186
9AL+3.3V
7LIGHT
22R3103
10
R3557
8P-ON+5V
210 KEY-IN1
OPEN
C3559
10K
R3185
215 REMOTE
205 LED1
100
R3183
OPEN
C3115
MM5Z5V6B
D3501
6LED1
OPEN
R3503
100
R3551
1
C3554
OPEN
C3555
5REMOTE
4.7KR3502
CN3101
1SDA(NU)
10
R3556
78 SCL
79 SDA
100K
R3560
OPEN
C3553
10
C3558
Q3502
2SA1576UBTLQ
33PC3552
10K
R3184
OPEN
R3555
2SC4081UBTLQ
Q3010
2SCL(NU)
10K
R3559
10K
R3112
100
R3553
4.7KR3501
2SC4081UBTLQ
Q3501
4.7KR3116
OPEN
C3191
208 LIGHT
3GND
131 FACTORY-SEL
100R3201
UARTTXD0
UARTRXD0
C3550
OPEN
OPEN
R3535
Q3531
OPEN
0
R3536
10K
R3192
OPEN
R3534
0
R3353
135 SW-EN
OPEN
C3187
33P
C3908
D3901
MM5Z5V6B
L3913
OPEN
D3904
MM5Z5V6B
TU3901 (TUNER UNIT)
1
+3.3V2GND3SDA4SCL5IF-AGC6DIF-OUT17DIF-OUT2
4.7K
R3937
OPEN
C3934
10
C3905
4.7K
R3938D3903
MM5Z5V6B
33P
C3909
0.022
C3168
0.1
C3910
D3902
MM5Z5V6B
OPEN
C3901
OPEN
C3904
OPEN
C3906
47
R320647R3207
100
R3936
TU-SDA125
TU-SCL126
0
R3179
10K
R3180
10
C3149
74 IF-AGC
L3104
22uH
33P
C3927
33P
C3926
0.1
C3174
0.1
C3173
33
R3151
33
R3152
OPEN
C3145 L3108
OPEN
OPEN
C3144
OPEN
C3150
70
71
IC3001(5/5)
MSD8200DS-S1
*1
51
R3181
0.1
C3142
0.1
C3143
51
R3187
123
IC3901
AP1117EG-13
VOUT
VIN
COM
100
R3903
33
R3902
220
R3901
10
C3911
220/6.3V
C3907
OPEN
C3912
24HDMI-ARC
OPEN
C3012
OPEN
R3082
AL+3.3V(1)
10K
R341722R3104
211 WAKE
10
R3822
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
HDMI
I/F
HDMICONNECTOR-3
HDMICONNECTOR-1
HDMICONNECTOR-2
AE
DIGITAL MAIN CBA UNIT
(SWITCHING)
(SWITCHING)
(SWITCHING)
2
4
1
3
AF AG AH AI AJ
TO DIGITAL
MAIN 4
IC3001(3/5)
VIDEO
DECODER
AUDIO
DECODER
(SWITCHING)
CONTINUE
DIGITAL 5
(SWITCHING)
(SWITCHING)
(SWITCHING)
(LED DRIVE)
TO FUNCTION CBA
UNIT CN4052
(BUFFER)
(LED DRIVE)
DEMODULATOR
/MPEG
DECODER
(+3.3V REG.)
TO DIGITAL
MAIN 4
IC3001(3/5)
TO DIGITAL
MAIN 4
IC3001(3/5)
TO DIGITAL
MAIN 4
IC3001(3/5)
CONTINUE
DIGITAL 4
The order of pins shown in this diagram is different from that of actual IC3001.
IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section.
1 NOTE:
Digital Main 6 Schematic Diagram [TYPE C]
PL13.11CSCD6
10-26
J207 P-ON-H2
J225 P-ON-H2
J226 AMP+13V
J232 P-ON+21V
J233 P-ON+21V
J234 P-ON+21V
J237 LDR1
J246 ILED2
J249 BL-ADJ
J256 LDO
BA31T0F0102 2
D
ISW2
C
12 3
Q657
Q658
L1001
L1002
R676
R678
R679
C651
C652
C653
C654
C655
C656
C662
C663
C667
C668
1
10
CN1001
11
2
J201
P-ON+21V
C1001
J202
P-ON+21V
C1002
J203
J204
GND
J205
GND
J206
AMP+13V
J208
AMP+13V
C1008
J209
RESET
C1009
J210
P-ON+21V
C1010
C1011
J214
ALL+3.3V
J219
GND
D651
D653
J220
D654
D655
J223
J224
GND
C1026
J227
P-ON+21V
C1027
J228
P-ON+21V
D1006
D662
J235
P-ON+21V
J239
P-ON-H2
J240
RESET
J241
J242
J243
LDR2
J244
VIN
J245
OVP1
J247
ILED4
J248
ILED6
J251
BL-ADJ
J252
GND
J253
BL-SW
J254
PROTECT3
J255
LDO
J257
BL-SW
J258
PROTECT3
J260
STATUS
J261
STATUS
GP002
GP001
J200
ALL+3.3V
R
1018
R1019
D1005
J236
ISW1
GND
J250
OVP2
J262
GND
GND
J263
J218
ALL+3.3V
D652
J238
P-ON+21V
D656A
LIVE
NEUTRAL
REPLACE FUSE AS MARKED
RISK OF FIRE-
HOT
COLD
T 2.5A L/250V
AB
R601
R602
R605
R610
R611
R619
CN601
C602
C603
C604
C605
C606
C611
C612
C614
C616
C617
C650
D601
D602
D603
D604
D607
D608
IC601
IC602
T601
J211
LED-CONT
J212
GND
J215
GND
D650
D659
D660
J231
GND
JS601
JS602
JS605
JS606
CN501
1
2
23
22
J259
GND
F602
Q601
L601
BC601
BC602
BC603
BC604
J101
GATE
J102
SOURCE
J104
FG
GP003
SA601
L602
JS603
JS604
JS609
D606A
BA31T0F01022
Power Supply CBA Top View
Because a hot chassis ground is present in the power supply
circuit, an isolation transformer must be used when repairing.
Also, in order to have the ability to increase the input slowly,
when troubleshooting this type of power supply circuit,
a variable isolation transformer is required.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F602) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
For continued protection against risk of fire,
replace only with same type 2.5A, 250V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
2.5A 250V
10-27
BA31T0F0102 2
T 2.5A L/250V
D
ISW2
ABC
123
Q657
Q658
R601
R602
R605
R610
R611
R619
CN601
L1001
L1002
C602
C603
C604
C605
C6
06
C611
C612
C614
C616
C617
R676
R678
R679
C650
C651
C652
C653
C654
C655
C656
D601
D602
C662
D603
C663
D604
C667
D607
C668
D608
IC601
IC602
T601
1
10
CN1001
11
2
J201
P-ON+21V
C1001
J202
P-ON+21V
C1002
J203
J204
GND
J205
GND
J206
AMP+13V
J207P-ON-H2
J208
AMP+13V
C1008
J209
RESET
C1009
J210
P-ON+21V
C1010
J211
LED-CONT
C1011
J212
GND
J214
ALL+3.3V
J215
GND
J219
GND
D650
D651
D653
J220
D654
D655
J223
J224
GND
J225P-ON-H2
D659
J226
AMP+13V
C1026
J227
P-ON+21V
C1027
J228
P-ON+21V
D1006
D660
D662
J231
GND
J232
P-ON+21V
J233
P-ON+21V
J234
P-ON+21V
J235
P-ON+21V
JS601
JS602
J237LDR1
J239
P-ON-H2
JS605
JS606
J240
RESET
J241
CN501
1
2
23
22
J242
J243
LDR2
J244
VIN
J245
OVP1
J246ILED2
J247
ILED4
J248
ILED6
J249BL-ADJ
J251
BL-ADJ
J252
GND
J253
BL-SW
J254
PROTECT3
J255
LDO
J256LDO
J257
BL-SW
J258
PROTECT3
J259
GND
J260
STATUS
J261
STATUS
F602
Q601
L601
BC601
BC602
BC603
BC604
J101
GATE
J102
SOURCE
J104
FG
GP003
GP002
GP001
SA601
J200
ALL+3.3V
R1018
R1019
D1005
J236
ISW1
GND
J250
OVP2
J262
GND
GND
J263
L602
J218
ALL+3.3V
JS603
JS604
JS609
D652
J238
P-ON+21V
D656A
D606A
R603
R604
R606
R607
R608
R612
R613
R614
D650A
D651A
D652A
D653A
R654
D654A
R655
R657
C621
C622
R663
R664
D655A
R665
R683
R684
R685
R686
R687
R688
R689
R693
D659A
Q1001
Q1002
C1012
C1013
C1014
C1015
C1018
C1019
D1001
D1002
IC1001
IC1002
R1014
R1015
IC651
R1016
R1017
D608A
Q658A
Q657A
R1035
R1036
D1021
C1031
R1021
R1022
C1032
R1034
R1041
C1043
C1039
R1050
C1006
R1010
D1003
R1052
R1012
C1024
C1022
C1005
C1004
C1003
R675
R674
R666
R667
Q653
D661
R669
R668
R659
R660
R661
R658
C660
C666
C610
D610
Q621
D609A
R609
Q602
C608
C609
R623
R622
C623
R621
D605
D623
D621
C1007
R1001
R1002
D1050
C1041
C1016
D1022
R1023
C1033
D1023
C1037
R1037
R1038
R1039
R1028
R1030
R1027
D1024
C1034
R1024
R1025
R1029
C1020
R1009
R1040
R1042
C1044
R1013
C1023
R1011
C1025
C607
D607A
R651
R694
D657
C701
R702
R701
Q701Q702
R704
R703
R1003
R1004
D1051
R1051
R1053
C1042
C1017
C1040
C1021
R1047
R1008
C630
C632
R1005
R690
R673
R670
C631
R1006
C1035
D1025
R1026
C1036
C1038
D1026
R1033
R1032
R1031
R1007
C664
Q656
R671
R672
D405
D663
R677
R656
R653
R652
Q650
R691
Q659
R692
C639
C638
C636
C635
C633
R681
C661
R682
C665
R680
R662
D1004
D406
D658
D606
D656
Power Supply CBA Bottom View
BA31T0F01022
Because a hot chassis ground is present in the power supply
circuit, an isolation transformer must be used when repairing.
Also, in order to have the ability to increase the input slowly,
when troubleshooting this type of power supply circuit,
a variable isolation transformer is required.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F602) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
For continued protection against risk of fire,
replace only with same type 2.5A, 250V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
2.5A 250V
[TYPE A]
WIRING DIAGRAM
9
CN4052
1
CN3105
FUNCTION CBA UNIT
CL3101
1
9
AC CORD
CN601
BW
1
CN501
1
CN3601
CL3701
CN1001
111
LCD PANEL ASSEMBLY
23
CL3011
23
1
CN3906
51
SP3802
SPEAKER
R-CH
SP3801
SPEAKER
CL3801
L-CH
CN3801
14
TUNER UNIT
COMPONENT
-Y/VIDEO-IN
COMPONENT
-Pb-IN
COMPONENT
-Pr-IN
AUDIO(L)-IN
REAR
AUDIO(R)-IN
DIGITAL
DIGITAL MAIN CBA UNIT POWER SUPPLY CBA
AUDIO-OUT
(COAXIAL)
ETHERNET
JACK
HDMI-
CONNECTOR-1
HDMI-
CONNECTOR-2
HDMI-
CONNECTOR-3
PC-RGB-IN
SIDE
WIRELESS
LAN MODULE
USB JACK
PL13.11AWI11-1
HEADPHONE
JACK
[TYPE B]
9
CN4052
1
CN3101
FUNCTION CBA UNIT
CL3101
1
9
AC CORD
CN601
BW
23
CN501
1
CN3701
POWER SUPPLY CBA
CL3701
CN1001
111
LCD PANEL ASSEMBLY
1
CL3011
23
1
CN3013
51
SP3802
SPEAKER
R-CH
SP3801
SPEAKER
CL3801
L-CH
CN3801
14
TUNER UNIT
COMPONENT
-Y/VIDEO-IN
COMPONENT
-Pb-IN
COMPONENT
-Pr-IN
AUDIO(L)-IN
REAR
AUDIO(R)-IN
DIGITAL
DIGITAL MAIN CBA UNIT
AUDIO-OUT
(COAXIAL)
HDMI-
CONNECTOR-1
HDMI-
CONNECTOR-2
HDMI-
CONNECTOR-3
PC-RGB-IN
SIDE
USB JACK
PL13.11BWI11-2
HEADPHONE
JACK
[TYPE C]
9
CN4052
1
CN3101
FUNCTION CBA UNIT
CL3101
AC CORD
1
9
CN601
BW
CN501
POWER SUPPLY CBA
23
1
CN3602
CL3701
CN1001
16
LCD PANEL ASSEMBLY
1
CL3011
1
23
CN3013
51
SP3802
SPEAKER
R-CH
SP3801
SPEAKER
CL3801
L-CH
CN3801
14
TUNER UNIT
COMPONENT
-Y/VIDEO-IN
COMPONENT
-Pb-IN
COMPONENT
-Pr-IN
AUDIO(L)-IN
REAR
AUDIO(R)-IN
DIGITAL
11-3
DIGITAL MAIN CBA UNIT
AUDIO-OUT
(COAXIAL)
HDMI-
CONNECTOR-1
HDMI-
CONNECTOR-2
HDMI-
CONNECTOR-3
PC-RGB-IN
SIDE
USB JACK
HEADPHONE
JACK
PL13.11CWI
12-1 PL13.11_A CEX
EXPLODED VIEWS
[TYPE A]
LCD1
B23
S7
A16
L23
L23
A13
B17
B17
B18
B18
L9
L67
B10
SP3802
SP3801
A17
A3
L27
L9
L9
X6
SBA1
A15
S7
SSK1
SSK2
A4
A6
A9
B12
A1
L9
L9
L9
Power Supply CBA
Digital Main CBA Unit
See Electrical Parts List
for parts with this mark.
Function CBA Unit
CL3701
CL3801
CL3101
SNA1
AC601
L23
CL3011
L23
B19
L35
[39PFL2608/F7]
[39PFL2908/F7,
39PFL4408/F8]
[39PFL2608/F7,
39PFL2908/F7]
12-2 PL13.11_B CEX
[TYPE B, C]
LCD1
B23
S7
A16
L23
L23
A13
B17
B17
B18
B18
L9
L67
B10
SP3802
SP3801
A17
A3
L27
L9
L9
X6
SBA1
A15
S7
SSK1
SSK2
A4
A6
A9
B12
A1
L9
L9
L9
Power Supply CBA
Digital Main CBA Unit
See Electrical Parts List
for parts with this mark.
Function CBA Unit
CL3701
CL3801
CL3101
SNA1
AC601
L23
CL3011
L23
B19
L35
A19
[39PFL2708/F7]
Packing
FRONT
FRONT
Packing Tape
Packing Tape
Packing Tape
Some Ref. Numbers are
not in sequence.
S7
S4
S1
SBA1
S6
SSK2
SSK1
X1
X4
X3
S7
X7
Tape
X2
S3
S3
SNA1
[39PFL2608/F7]
[39PFL2708/F7,
39PFL2908/F7,
39PFL4208/F8,
39PFL4408/F8]
[39PFL2608/F7]
S12
[39PFL4208/F8,
39PFL4408/F8]
[39PFL2608/F7,
39PFL2708/F7,
39PFL2908/F7]
[39PFL2708/F7,
39PFL2908/F7,
39PFL4208/F8,
39PFL4408/F8]
12-3 PL13.11_PEX
TYPE A
PARTS LIST [39PFL2608/F7 (Serial No.: DS1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Ref. No. Description Part No.
A3 REAR COVER A3RP0UH 1EM030705
A13 JACK HOLDER A37U0UH 1EM334736
A15# RATING LABEL A3RTBUH ---------A16 LOGO LABEL A3RM0UT ---------A17 ENERGY GUIDE LABEL A3RTBUH ---------AC601# AC CORD W/O A GND WIRE UL/CSA/1700/NO/
B10 STAND HOLDER A31T0UH 1EM127914
B17 WALL MOUNT BRACKET A11N0UH 1EM434637
B18 WALL MOUNT COVER A2170UT 1EM332137
B23 WIRE LABEL A3AF0UT ---------CL3101 FFC WIRE ASSEMBLY 9PIN 9PIN/WHITE/
CL3701 FFC WIRE ASSEMBLY 23PIN 23PIN/WHITE/
CL3801 WIRE ASSEMBLY 4PIN 4PIN/320MM&90MM WX1A31T0C301
L9 SCREW P-TIGHT 3X12 BIND HEAD+ BLK GBHP3120
L23 SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060
L27 SCREW S-TIGHT M3X8 BIND HEAD+ GBHS3080
L67 SCREW S-TIGHT M3X10 BIND HEAD+ GBJS3100
SBA1 STAND BASE ASSEMBLY A31T0UH 1EM030366
SNA1 STAND NECK ASSEMBLY A31T0UH 1EM030365
SP3801 SPEAKER MAGNETIC 8Ω/8W S0310F15 DS08110XQ003
SP3802 SPEAKER MAGNETIC 8Ω/8W S0310F15 DS08110XQ003
SSK1 STAND SCREW KIT A31T0UH(DOUBLE SEMS
SSK2 STAND SCREW KIT A31T0UH(DOUBLE SEMS
BLACK
130MM
75MM
SCREW M4X20 + BLK)
SCREW M4X10 + BLK)
PAC K IN G
S1 CARTON A3RTBUH 2EMC00041
S3 STYROFOAM TOP A31T0UH 1EM030609
S4 STYROFOAM BOTTOM A31T0UH 1EM030610A
S6 SET BAG A31PBUH 2EMC00084
S7 SERIAL NO. LABEL A01PBUH ----------
ACCESSORIES
X1 POLYETHYLENE BAG HDPE 180X340XT0.03 1EM435579
X2# OWNERS MANUAL A3RT0UH 2EMN00086
X3 REMOTE CONTROL UNIT YKF340-001 URMT39JHG003
X4 BATTERY R03-B500/01S XB0M451CZB01
X6 QUICK START GUIDE A3RT0UH 1EMN30387
X7 REGISTRATION CARD(PHILIPS) A11P4UH 1EMN27321
WAC172LTE005
WX1A31T0S102
WX1A3RP0S101
1ESA34647
1ESA34648
LCD PANEL ASSEMBLY
Ref. No. Description Part No.
LCD1# LCD PANEL ASSEMBLY U30T1P1
Consists of the following
A1 FRONT CABINET A31T2UH 1EM127996
A4 X -PCB COVER A31T0UH 1EM228323
A6 CONTROL PLATE A31F0UT 1EM334317
A9 SENSOR LENS A31F0UT 1EM334217
B12 SHIELD PLATE A31F0UT 1EM334218
CL3011 FFC WIRE ASSEMBLY 51PIN(W/SHIELD) 51P/
L9 SCREW P-TIGHT 3X12 BIND HEAD+ BLK GBHP3120
FFC/SHIELD/307MM
LCD MODULE ----------
WX1A3RT0P402
2013/02/18 13-1 A3RTBCA.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
DIGITAL MAIN CBA UNIT
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT A3RTBMMA-007
CN3701 WIRELESS LAN MODULE WM5504 UWLMDLACM002
IC3101 IC MAIN PH1-SLD8 MN2WS0270EA QSCA0R0MS053
IC3102 IC NAND FLASH 1GB K9F1G08U0D-SCB0 NSCA0R0SM037
IC3103 16KBIT EEPROM M24C16-WMN6TP NSZBA0TSS259
IC3601 IC RESET IC-PST8429UR QSCA0T0MM075
IC3602 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021
IC3603 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021
IC3604 IC DCDC CONVERTER RT8293ALZSP NSCA0T00B017
IC3607 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021
IC3701 IC USB HIGH-SIDE SW AP2151WG-7/SOT25/
IC3803 IC D-CLASS AUDIO POWER AMPLIFI
TU3001 TUNER UNIT U9001UH U9001UH
IC3401 IC 1GB DDR3 SDRAM K4B1G1646G-BCH9 NSCA0R0SM043
IC3402 IC 1GB DDR3 SDRAM K4B1G1646G-BCH9 NSCA0R0SM043
IC3401 IC 1GB DDR3 SDRAM H5TQ1G63DFR-H9C NSCA0R0HY018
IC3402 IC 1GB DDR3 SDRAM H5TQ1G63DFR-H9C NSCA0R0HY018
IC3401 IC 1GB DDR3 SDRAM H5TQ1G63EFR-H9C NSCA0R0HY035
IC3402 IC 1GB DDR3 SDRAM H5TQ1G63EFR-H9C NSCA0R0HY035
5PI
TPA3110D2PWPR
When you replace one of the below ICs on this CBA, replace with the
one that has the same part number. Do not mix ICs with different part
number.
or
or
NSCA0TDES015
NSCA0T0TY073
FUNCTION CBA UNIT
Ref. No. Description Part No.
FUNCTION CBA UNIT A3RT0MSW-001
IC4051 IC LIGHT SENSOR PH5502B2NA1-E4 QP1ZPH5502B2
POWER SUPPLY CBA
Ref. No. Description Part No.
POWER SUPPLY CBA
Consists fo the following
A3RT0MPW-002
Ref. No. Description Part No.
CAPACITORS
C602# SAFTY CAP. 2200pF/250V KX CA2E222MR101
C604# CAP METALLIZED FILM 0.22µF/310V /K/LE-MX CTA2240DC001
C605 CAP ELE 220µF/200V/M/85 CEB2210S6016
C606 CERAMIC CAP. 680pF/2kV CA3D681PAN04
C607 CHIP CERAMIC CAP. B K 1200pF/50V CHD1JK30B122
C608 CHIP CERAMIC CAP.(1608) B K 0.033µF/50V CHD1JK30B333
C609 CHIP CERAMIC CAP. B K 0.068µF/50V CHD1JK30B683
C610 CHIP CERAMIC CAP. B K 1500pF/50V CHD1JK30B152
C611 CAP ELE 220µF/200V/M/85 CEB2210S6016
C612 CAP CERAMIC HV 1500PF 1kV B K CA3A152TE006
C614# CAP METALLIZED FILM 0.22µF/310V /K/LE-MX CTA2240DC001
C623 CHIP CERAMIC CAP.(1608) B K 4.7µF/6.3V CHD0KK30B475
C650 CAP CERAMIC HV 2200pF/1kV B K CA3A222TE006
C651 CAP ELE 470µF/25V/M/85 CED4710V8006
C652 CAP ELE 470µF/25V/M/85 CED4710V8006
C653 CAP ELE 470µF/25V/M/85 CED4710V8006
C654 CAP ELE 470µF/16V/M/85 CEC4710V8006
C655 CAP ELE 470µF/16V/M/85 CEC4710V8006
C656 CAP ELE 4.7µF/50V/M/85 CEF4R70V8006
C660 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C663 CAP ELE 100µF/10V/M/85 CEB1010V8006
C665 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C667 CAP ELE 470µF/25V/M/85 CED4710V8006
C668 CAP ELE 470µF/25V/M/85 CED4710V8006
C1001 CAP ELE 330µF/25V/M/85 CED3310V8006
C1002 CAP ELE 330µF/25V/M/85 CED3310V8006
C1003 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C1004 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C1006 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C1007 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C1008 CAP ELE 47µF/100V/M/85 CEH4700V8006
C1009 CAP ELE 47µF/100V/M/85 CEH4700V8006
C1010 CAP ELE 47µF/100V/M/85 CEH4700V8006
C1011 CAP ELE 47µF/100V/M/85 CEH4700V8006
C1014 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1015 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1016 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1017 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1018 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1019 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1022 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1023 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1026 CAP CERAMIC HV 220pF/500V/B/K CCA221YNA001
C1027 CAP CERAMIC HV 220pF/500V/B/K CCA221YNA001
C1037 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1038 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1041 CHIP CERAMIC CAP.(1608) B K 4.7µF/6.3V CHD0KK30B475
C1042 CHIP CERAMIC CAP.(1608) B K 4.7µF/6.3V CHD0KK30B475
C1043 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C1044 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
CONNECTORS
CN501 FFC CONNECTOR IMSA-9615S-23A-PP-A JC96J23ER007
CN601# CONNECTOR S2P3-VH (LF)(SN) JCVHC02JG002
CN1001 FFC CONNECTOR IMSA-9615S-11A-PP-A JC96J11ER007
DIODES
D601 DIODE 1N5406BH NDL1001N5406
D602 DIODE 1N5406BH NDL1001N5406
D603 DIODE 1N5406BH NDL1001N5406
2013/02/18 13-2 A3RTBEL.fm
Ref. No. Description Part No.
D604 DIODE 1N5406BH NDL1001N5406
D605 ZENER DIODE MM5Z6V2B ND1BMM5Z6V2B
D606 DIODE FAST RECOVERY RS1JJTD ND1Z0RS1JJTD
D607A# ZENER DIODE SMD TFZVTR27B QD1B00TFZV27
D608# DIODE ZENER 1ZB36BB NDWZ0001ZB36
D609A# DIODE SCHOTTKY SMD CES520.L3F(D QD1Z00CES520
D610 SWITCHING DIODE 1SS400 TE61 QD1Z001SS400
D621 SWITCHING DIODE 1SS400 TE61 QD1Z001SS400
D623 ZENER DIODE MM5Z30B ND1B0MM5Z30B
D650 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
D651 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
D652# DIODE ZENER 1ZB30BB NDWZ0001ZB30
D653 DIODE SCHOTTKY SB3A0BH NDWZ000SB3A0
D654# DIODE ZENER 1ZB20BB NDWZ0001ZB20
D655 DIODE SCHOTTKY SB3A0BH NDWZ000SB3A0
D656 DIODE FAST RECOVERY RS1BJTD ND1Z0RS1BJTD
D657 ZENER DIODE MM5Z11B ND1B0MM5Z11B
D659 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
D660 IC SHUNT REGULATOR SL431A-AT NSZBA0TAUK01
D661 SWITCHING DIODE 1SS400 TE61 QD1Z001SS400
D662 IC SHUNT REGULATOR SL431A-AT NSZBA0TAUK01
D1001 DIODE SCHOTTKY SMD SK210TD ND1Z0SK210TD
D1002 DIODE SCHOTTKY SMD SK210TD ND1Z0SK210TD
D1003 SWITCHING DIODE 1SS400 TE61 QD1Z001SS400
D1004 SWITCHING DIODE 1SS400 TE61 QD1Z001SS400
ICS
IC602# IC PHOTOCOUPLER TLP781F(D4-FUNBLL F) QPEL781FBLLF
IC1001 IC LED BACKLIGHT CONTROLLER HA7209PC
IC1002 IC LED BACKLIGHT CONTROLLER HA7209PC
/SOP /24PIN
/SOP /24PIN
NSCA0T00H003
NSCA0T00H003
COILS
L601# LINE FILTER JLB24136 LLEG0Z0XB032
L602# LINE FILTER JLB24136 LLEG0Z0XB032
L1001 POWER INDUCTORS CWKBNP-220K LLF2200KV002
L1002 POWER INDUCTORS CWKBNP-220K LLF2200KV002
TRANSISTORS
Q601# FET MOS TK10A50D(LS1FN3 QM QEEZTK10A50D
Q602# NPN TRANSISTOR SMD 2SC5344SY NQZY2SC5344S
Q621 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q650 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q653 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q656 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q658 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F
Q1001 FET MOS SMD AP18T10AGH-HF NF2Z18T10AGH
Q1002 FET MOS SMD AP18T10AGH-HF NF2Z18T10AGH
RESISTORS
R601# RES. CARBON FILM J 1/2W J 1.2M Ω RCX2125T1003
R603 RES CHIP 3216 1/4W J 560k Ω RRX4564HH034
R604 RES CHIP 3216 1/4W J 560k Ω RRX4564HH034
R606 RES CHIP 3216 1/4W J 120 Ω RRX4121HH034
R607 RES CHIP 3216 1/4W J 120 Ω RRX4121HH034
R608 RES CHIP 3216 1/4W J 1.2k Ω RRX4122HH034
R609 RES CHIP 1608 1/10W J 100 Ω RRXA101HH013
R611# METAL OXIDE RES. 2W J 0.3 Ω RN02R30ZU001
R612 RES CHIP 3216 1/4W J 3.9k Ω RRX4392HH034
R613 RES CHIP 3216 1/4W J 270 Ω RRX4271HH034
R614 RES CHIP 3216 1/4W J 560k Ω RRX4564HH034
R619 METAL OXIDE FILM RES. 1W J 100k Ω RN01104ZU001
R621 RES CHIP 1608 1/10W J 560 Ω RRXA561HH013
R622 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R623 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R651# RES CHIP 1608 1/10W J 1.0 Ω RRXA1R0HH013
Ref. No. Description Part No.
R652 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R653 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R654 RES CHIP 3216 1/4W J 180 Ω RRX4181HH034
R655 RES CHIP 3216 1/4W J 180 Ω RRX4181HH034
R656 RES CHIP 1608 1/10W F 33.0k Ω RTW3302HH008
R657 RES CHIP 3216 1/4W J 3.9k Ω RRX4392HH034
R658 RES CHIP 1608 1/10W J 2.7k Ω RRXA272HH013
R659 RES CHIP 1608 1/10W F 22.0k Ω RTW2202HH008
R660 RES CHIP 1608 1/10W F 2.70k Ω RTW2701HH008
R661 RES CHIP 1608 1/10W F 3.30k Ω RTW3301HH008
R662 RES CHIP 1608 1/10W F 3.30k Ω RTW3301HH008
R663 RES CHIP 3216 1/4W J 4.7k Ω RRX4472HH034
R666 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R667 RES CHIP 1608 1/10W J 8.2k Ω RRXA822HH013
R668 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013
R669 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R670 RES CHIP 1608 1/10W J 270 Ω RRXA271HH013
R671 RES CHIP 1608 1/10W J 270 Ω RRXA271HH013
R672 RES CHIP 1608 1/10W J 270 Ω RRXA271HH013
R677 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R680 RES CHIP 1608 1/10W J 100 Ω RRXA101HH013
R681 RES CHIP 1608 1/10W F 10.0k Ω RTW1002HH008
R682 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R690# RES CHIP 1608 1/10W J 1.5 Ω RRXA1R5HH013
R694 RES CHIP 1608 1/10W J 33k Ω RRXA333HH013
R1001 RES CHIP 1608 1/10W J 360 Ω RRXA361HH013
R1002 RES CHIP 1608 1/10W J 360 Ω RRXA361HH013
R1003 RES CHIP 1608 1/10W J 360 Ω RRXA361HH013
R1004 RES CHIP 1608 1/10W J 360 Ω RRXA361HH013
R1005 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R1006 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1007 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R1008 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1009 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R1010 RES CHIP 1608 1/10W J 10 Ω RRXA100HH013
R1011 RES CHIP 1608 1/10W J 10 Ω RRXA100HH013
R1012 RES CHIP 1608 1/10W J 200 Ω RRXA201HH013
R1013 RES CHIP 1608 1/10W J 200 Ω RRXA201HH013
R1018 METAL OXIDE FILM RES. 2W J 0.18 Ω RN02R18ZU001
R1019 METAL OXIDE FILM RES. 2W J 0.18 Ω RN02R18ZU001
R1021 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1022 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1023 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1024 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1025 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1026 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1027 RES CHIP 1608 1/10W F 13.0k Ω RTW1302HH008
R1028 RES CHIP 1608 1/10W F 330 Ω RTW3300HH008
R1029 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1030 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R1031 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R1032 RES CHIP 1608 1/10W F 13.0k Ω RTW1302HH008
R1033 RES CHIP 1608 1/10W F 330 Ω RTW3300HH008
R1034 RES CHIP 1608 1/10W F 510k Ω RTW5103HH008
R1035 RES CHIP 1608 1/10W F 430k Ω RTW4303HH008
R1036 RES CHIP 1608 1/10W F 27.0k Ω RTW2702HH008
R1037 RES CHIP 1608 1/10W F 510k Ω RTW5103HH008
R1038 RES CHIP 1608 1/10W F 430k Ω RTW4303HH008
R1039 RES CHIP 1608 1/10W F 27.0k Ω RTW2702HH008
R1040 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1041 RES CHIP 1608 1/10W F 100 Ω RTW1000HH008
R1042 RES CHIP 1608 1/10W F 100 Ω RTW1000HH008
R1047 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
2013/02/18 13-3 A3RTBEL.fm
Ref. No. Description Part No.
MISCELLANEOUS
B19 HEAT SINK PNL A31T0UH 1EM439707
BC601 WIRE CP STP-S-0.50 XZ40F0REN001
BC602 WIRE CP STP-S-0.50 XZ40F0REN001
BC603 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC604 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
F602# FUSE TIME RAG SLT250V2.5A PDGSLB0NG252
JS603 WIRE CP STP-S-0.50 XZ40F0REN001
JS604 WIRE CP STP-S-0.50 XZ40F0REN001
JS609 WIRE CP STP-S-0.50 XZ40F0REN001
L35 SCREW B-TIGHT D3X8 BIND HEAD+ GBJB3080
SA601# VARISTOR 10D 471K SVR NVQZVR10D471
T601# TRANS POWER BCK-28F0 LTT2PCMEK058
2013/02/18 13-4 A3RTBEL.fm
TYPE A
PARTS LIST [39PFL2608/F7 (Serial No.: DS2)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
39PFL2608/F7 (Serial No.: DS1)
Ref. No. Description Part No.
A17 ENERGY GUIDE LABEL A3RTCUH ---------LCD1# LCD PANEL ASSEMBLY U30T9P0
2013/06/24 13-5 A3RTCCA.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Different parts from the original model
39PFL2608/F7 (Serial No.: DS1)
Ref. No. Description Part No.
POWER SUPPLY CBA A3RTCMPW-001
R1027 RES CHIP 1608 1/10W F 12.0k Ω RTW1202HH008
R1028 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1032 RES CHIP 1608 1/10W F 12.0k Ω RTW1202HH008
R1033 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
2013/06/24 13-6 A3RTCEL.fm
TYPE A
PARTS LIST [39PFL2908/F7 (Serial No.: DS1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
39PFL2608/F7 (Serial No. : DS1)
Ref. No. Description Part No.
A15# RATING LABEL A3RT0UH ---------A17 ENERGY GUIDE LABEL A3RT0UH ---------SBA1 STAND BASE ASSEMBLY A31T2UH 1EM030546
SNA1 STAND NECK A31T2UH 1EM030545A
S1 CARTON A3RT0UH 1EM334658
2013/04/08 13-7 A3RT0CA.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Different parts from the original model
39PFL2608/F7 (Serial No. : DS1)
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT A3RT0MM A-003
2013/04/08 13-8 A3RT0EL.fm
TYPE A
PARTS LIST [39PFL4408/F8 (Serial No.: XA1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
39PFL2608/F7 (Serial No.: DS1)
Ref. No. Description Part No.
A15# RATING LABEL A3RTAMA ---------A16 LOGO LABEL A3RFAMA ---------A17 Not used ---------SBA1 STAND BASE ASSEMBLY A31T2UH 1EM030546
SNA1 STAND NECK A31T2UH 1EM030545A
S1 CARTON A3RTAMA 2EMC00031
S12 CARTON LABEL A3RTAMA ---------X2# OWNERS MANUAL A3RTAMA 2EMN00024A
X6 QUICK START GUIDE A3RTAMA 2EMN00025
X7 Not used
2013/04/11 13-9 A3RTACA.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Different parts from the original model
39PFL2608/F7 (Serial No.: DS1)
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT A3RTAMMA-004
2013/04/11 13-10 A3RTAEL.fm
TYPE B
PARTS LIST [39PFL2708/F7 (Serial No.: DS2)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
39PFL2608/F7 (Serial No.: DS1)
Ref. No. Description Part No.
A33 REAR COVER A31T0UH 1EM030350
A13 JACK HOLDER A3AU0UH 1EM334651
A15# RATING LABEL A31T2UH ---------A16 LOGO LABEL A31M2UT ---------A17 ENERGY GUIDE LABEL A31T2UH ---------A19 JACK LABEL A31T0UH 1EM440016
CL3701 FFC WIRE ASSEMBLY 23PIN 23PIN/WHITE/
SBA1 STAND BASE ASSEMBLY A31T2UH 1EM030546
SNA1 STAND NECK A31T2UH 1EM030545A
S1 CARTON A31T2UH 1EM334657
X2# OWNERS MANUAL A31T2UH 2EMN00084
X3 REMOTE CONTROL UNIT YKF335-001 URMT39JHG001
X6 QUICK START GUIDE A31T2UH 1EMN30381
LCD1# LCD PANEL ASSEMBLY U30T1P0
CL3011 FFC WIRE ASSEMBLY 51PIN(W/SHIELD) 51P/
110MM
FFC/SHIELD/270MM
WX1A31T0S103
WX1A31T0P402
2013/03/14 13-11 A31TCCA.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Different parts from the original model
39PFL2608/F7 (Serial No. : DS1)
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT A31TCMMA-001
CN3701 Not used
IC3001 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021
IC3002 IC 512MB DDR2 SDRAM K4T51163QJ-BCE7 NSCA0R0SM048
IC3003 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021
IC3004 IC REGULATOR BD00IA5WEFJ-E2 QSCA0T0RM233
IC3005 IC DTV-C7V R8A05011BG-U0/256FHP QSAA0R0HT057
IC3006 32MBIT C-MOS SERIAL FLASH
IC3007 IC LDO REGULATOR BD00IC0WEFJ/HTSOP-J8QSCA0T0RM397
S25FL032P0XMFI010 /S
QSCA0R0FJ008
Ref. No. Description Part No.
POWER SUPPLY CBA A31TBMPW-001
C662 CAP ELE 22µF/50V/M/85 CEF2200V8006
IC651 IC REGULATOR AP1117E33G-13 /3PIN NSCA0TDES017
R676 WIRE CP STP-S-0.50 XZ40F0REN001
R678 METAL OXIDE RES. 2W J 0.3 Ω RN02R30ZU001
R679 METAL OXIDE RES. 2W J 0.3 Ω RN02R30ZU001
R683 RES CHIP 3216 1/4W 0 Ω RRX4000HH036
R684 RES CHIP 3216 1/4W 0 Ω RRX4000HH036
IC3008 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021
IC3009 IC RESET IC-PST8429UR QSCA0T0MM075
IC3011 IC EEPROM BU9883FV-WE2 QSCA0T0RM105
IC3013 IC SINGLE BUS BUFFER 74LVC1G126GW NSCA0TNXP004
IC3014 IC SINGLE BUS BUFFER 74LVC1G126GW NSCA0TNXP004
IC3018 IC HDMI SW TMDS351PAGR /PAG-64 NSCA0T0TY068
IC3019 IC USB HIGH-SIDE SW AP2151WG-7/SOT25/
IC3101 Not used
IC3102 Not used
IC3103 Not used
IC3601 IC REGULATOR AP2121AK-3.3TRE1 NSCA0TBCD026
IC3602 Not used
IC3603 Not used
IC3604 Not used
IC3607 Not used
IC3701 Not used
IC3801 IC D-CLASS AUDIO POWER AMPLIFI
IC3803 Not used
IC3851 IC HEADPHONE AMP BH3547F SOP 8PIN QSZBA0TRM119
TU3901 TUNER UNIT U9001UH U9001UH
TU3001 Not used
IC3401 Not used
IC3402 Not used
5PI
TPA3110D2PWPR
FUNCTION CBA UNIT A31TCMSW-001
NSCA0TDES015
NSCA0T0TY073
2013/03/14 13-12 A31TCEL.fm
TYPE C
PARTS LIST [39PFL2708/F7 (Serial No.: DS1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
39PFL2608/F7 (Serial No.: DS1)
Ref. No. Description Part No.
A33 REAR COVER A31T0UH 1EM030350
A13 JACK HOLDER A3AU0UH 1EM334651
A15# RATING LABEL A31T2UH ---------A16 LOGO LABEL A31M2UT ---------A17 ENERGY GUIDE LABEL A31T2UH ---------A19 JACK LABEL A31T0UH 1EM440016
CL3701 FFC WIRE ASSEMBLY 23PIN 23PIN/WHITE/
SBA1 STAND BASE ASSEMBLY A31T2UH 1EM030546
SNA1 STAND NECK A31T2UH 1EM030545A
S1 CARTON A31T2UH 1EM334657
X2# OWNERS MANUAL A31T2UH 2EMN00084
X3 REMOTE CONTROL UNIT YKF335-001 URMT39JHG001
X6 QUICK START GUIDE A31T2UH 1EMN30381
LCD1# LCD PANEL ASSEMBLY U30T1P0
CL3011 FFC WIRE ASSEMBLY 51PIN(W/SHIELD) 51P/
110MM
FFC/SHIELD/270MM
WX1A31T0S103
WX1A31T0P402
2013/08/02 13-13 A31T2CA.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Different parts from the original model
39PFL2608/F7 (Serial No.: DS1)
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT A31T2MMA-004
CN3701 Not used
IC3001 IC MSD8200DS-S1 NSAA0RMST001
IC3002 IC 512MB DDR2 SDRAM K4T51163QJ-BCE7 NSCA0R0SM048
IC3006 IC 32M-BIT SERIAL FLASH MEMORY
IC3009 IC RESET IC-PST8429UR QSCA0T0MM075
IC3019 IC USB HIGH-SIDE SW AP2151WG-7/SOT25/
IC3101 Not used
IC3102 Not used
IC3103 Not used
IC3601 REGULATOR AP1117EG-13 NSCA0TDES012
IC3602 REGULATOR AP1117EG-13 NSCA0TDES012
IC3603 IC REGULATOR BD00IA5WEFJ-E2 QSCA0T0RM233
IC3605 IC DCDC CONVERTER RT8293ALZSP NSCA0T00B017
IC3607 Not used
IC3701 Not used
IC3801 IC D-CLASS AUDIO POWER AMPLIFI
IC3803 Not used
IC3901 REGULATOR AP1117EG-13 NSCA0TDES012
TU3001 Not used
TU3901 TUNER UNIT U9001UH U9001UH
IC3401 Not used
IC3402 Not used
W25Q32FVSSIG
5PI
TPA3110D2PWPR
NSCA0R0ZM018
NSCA0TDES015
NSCA0T0TY073
Ref. No. Description Part No.
R662 Not used
R670 Not used
R671 Not used
R672 Not used
R676 METAL OXIDE FILM RES. 2W J 4.7 Ω RN024R7ZU001
R678 METAL OXIDE FILM RES. 2W J 4.7 Ω RN024R7ZU001
R679 METAL OXIDE FILM RES. 2W J 4.7 Ω RN024R7ZU001
R680 Not used
R681 Not used
R682 Not used
R683 RES CHIP 3216 1/4W J 3.9 Ω RRX43R9HH034
R684 RES CHIP 3216 1/4W J 3.9 Ω RRX43R9HH034
R685 RES CHIP 3216 1/4W J 3.3 Ω RRX43R3HH034
R686 RES CHIP 3216 1/4W J 3.3 Ω RRX43R3HH034
R687 RES CHIP 3216 1/4W J 3.3 Ω RRX43R3HH034
R688 RES CHIP 3216 1/4W J 2.2 Ω RRX42R2HH034
R689 RES CHIP 3216 1/4W J 2.7 Ω RRX42R7HH034
R690# Not used
FUNCTION CBA UNIT A31T2MSW-001
POWER SUPPLY CBA A31T0MPW-002
C662 CAP ELE 22µF/50V/M/85 CEF2200V8006
C665 Not used
D662 Not used
IC651 IC REGULATOR AP1117E33G-13 /3PIN NSCA0TDES017
Q656 Not used
Q657 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F
Q658 Not used
2013/08/02 13-14 A31T2EL.fm
TYPE C
PARTS LIST [39PFL4208/F8 (Serial No.: XA1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
39PFL2608/F7 (Serial No.: DS1)
Ref. No. Description Part No.
A33 REAR COVER A31T0UH 1EM030350
A13 JACK HOLDER A3AU0UH 1EM334651
A15# RATING LABEL A31TAMA ---------A16 LOGO LABEL A31MAMA ---------A17 Not used ---------A19 JACK LABEL A31T0UH 1EM440016
CL3701 FFC WIRE ASSEMBLY 23PIN 23PIN/WHITE/
SBA1 STAND BASE ASSEMBLY A31T2UH 1EM030546
SNA1 STAND NECK A31T2UH 1EM030545A
S1 CARTON A31TAMA 2EMC00014
S12 CARTON LABEL A31TAMA ---------X2# OWNERS MANUAL A31TAMA 1EMN30390
X3 REMOTE CONTROL UNIT YKF335-001 URMT39JHG001
X6 QUICK START GUIDE A31TAMA 1EMN30391
X7 Not used
LCD1# LCD PANEL ASSEMBLY U30T1P0
CL3011 FFC WIRE ASSEMBLY 51PIN(W/SHIELD) 51P/
110MM
FFC/SHIELD/270MM
WX1A31T0S103
WX1A31T0P402
2013/04/17 13-15 A31TACA.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Different parts from the original model
39PFL2608/F7 (Serial No.: DS1)
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT A31TAMMA-002
CN3701 Not used
IC3001 IC MSD8200DS-S1 NSAA0RMST001
IC3002 IC 512MB DDR2 SDRAM K4T51163QJ-BCE7 NSCA0R0SM048
IC3006 IC 32M-BIT SERIAL FLASH MEMORY
IC3009 IC RESET IC-PST8429UR QSCA0T0MM075
IC3019 IC USB HIGH-SIDE SW AP2151WG-7/SOT25/
IC3101 Not used
IC3102 Not used
IC3103 Not used
IC3601 REGULATOR AP1117EG-13 NSCA0TDES012
IC3602 REGULATOR AP1117EG-13 NSCA0TDES012
IC3603 IC REGULATOR BD00IA5WEFJ-E2 QSCA0T0RM233
IC3605 IC DCDC CONVERTER RT8293ALZSP NSCA0T00B017
IC3607 Not used
IC3701 Not used
IC3801 IC D-CLASS AUDIO POWER AMPLIFI
IC3803 Not used
IC3901 REGULATOR AP1117EG-13 NSCA0TDES012
TU3001 Not used
TU3901 TUNER UNIT U9001UH U9001UH
IC3401 Not used
IC3402 Not used
W25Q32FVSSIG
5PI
TPA3110D2PWPR
NSCA0R0ZM018
NSCA0TDES015
NSCA0T0TY073
Ref. No. Description Part No.
R662 Not used
R670 Not used
R671 Not used
R672 Not used
R676 METAL OXIDE FILM RES. 2W J 4.7 Ω RN024R7ZU001
R678 METAL OXIDE FILM RES. 2W J 4.7 Ω RN024R7ZU001
R679 METAL OXIDE FILM RES. 2W J 4.7 Ω RN024R7ZU001
R680 Not used
R681 Not used
R682 Not used
R683 RES CHIP 3216 1/4W J 3.9 Ω RRX43R9HH034
R684 RES CHIP 3216 1/4W J 3.9 Ω RRX43R9HH034
R685 RES CHIP 3216 1/4W J 3.3 Ω RRX43R3HH034
R686 RES CHIP 3216 1/4W J 3.3 Ω RRX43R3HH034
R687 RES CHIP 3216 1/4W J 3.3 Ω RRX43R3HH034
R688 RES CHIP 3216 1/4W J 2.2 Ω RRX42R2HH034
R689 RES CHIP 3216 1/4W J 2.7 Ω RRX42R7HH034
R690# Not used
FUNCTION CBA UNIT A31T2MSW-001
POWER SUPPLY CBA A31T0MPW-002
C662 CAP ELE 22µF/50V/M/85 CEF2200V8006
C665 Not used
D662 Not used
IC651 IC REGULATOR AP1117E33G-13 /3PIN NSCA0TDES017
Q656 Not used
Q657 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F
Q658 Not used
2013/04/17 13-16 A31TAEL.fm
REVISION HISTORY
Chassis PL13.11
• 2013/02/28 39PFL2608/F7 (Serial No.: DS1) Added
• 2013/03/27 39PFL2708/F7 (Serial No.: DS2) Added
• 2013/04/19 39PFL2908/F7 (Serial No.: DS1) Added
• 2013/04/30 39PFL4208/F8 (Serial No.: XA1) Added
• 2013/06/05 39PFL4408/F8 (Serial No.: XA1) Added
• 2013/06/28 39PFL2608/F7 (Serial No.: DS2) Added
• 2013/08/17 39PFL2708/F7 (Serial No.: DS1) Added
14-1 PL13.11REV
COMPARISON LIST OF MODEL NAMES
Chassis PL13.11
39PFL2608/F7 (DS1) A3RTBUH TYPE A
(DS2) A3RTCUH TYPE A
39PFL2708/F7 (DS1) A31T2UH TYPE C
(DS2) A31TCUH TYPE B
39PFL2908/F7 (DS1) A3RT0UH TYPE A
39PFL4208/F8 (XA1) A31TAMA TYPE C
39PFL4408/F8 (XA1) A3RTAMA TYPE A
PL13.11COM
Loading...