Register your product and get support at
www.philips.com/welcome
39PFL3559/V7
EN User manual
Cover 2 Blank
Contents
1 Notice 2
2 Important 3
Product disposal Guidelines 4
Use your TV 5
3
4
Use more of your TV 9
5
Play photos, music and videos
o n USB storage devices
6 Troubleshooting
7 Product information
8
Consumer Guidelines
Warranty
9
16
18
21
23
24
EN 1
1 Notice
Pixel characteristics
This LCD/LED product has a high number of
color pixels. Although it has effective pixels of
99.999% or more, black dots or bright points of
light (red, green or blue) may appear constantly
on the screen. This is a structural property of
the display (within common industry standards)
and is not a malfunction.
Warranty
No components are user serviceable. Do not
open or remove covers to the inside of the
product. Repairs may only be done by Philips
Service Centers and official repair shops.
Failure to do shall void any warranty, stated
or implied.
Any operation expressly prohibited in
this manual, or any adjustments and
assembly procedures not recommended
or authorised in this manual shall void the
warranty.
EN 2
2 Important
Read and understand all instructions before you
use your TV. If damage is caused by failure to
follow instructions, the warranty does not apply.
Safety
Risk of electric shock or fire!
• Never expose the TV to rain or water.
Never place liquid containers, such as
vases, near the TV. If liquids are spilt on
or into the TV, disconnect the TV from
the power outlet immediately. Contact
Philips Consumer Care to have the TV
checked before use.
• Never place the TV, remote control or
batteries near naked flames or other
heat sources, including direct sunlight. To
prevent the spread of fire, keep candles
or other flames away from the TV, remote
control and batteries at all times.
• Never insert objects into the ventilation
slots or other openings on the TV.
• When the TV is swivelled ensure that
no strain is exerted on the power cord.
Strain on the power cord can loosen
connections and cause arcing.
Risk of short circuit or fire!
• Never expose the remote control or
batteries to rain, water or excessive heat.
• Avoid force coming onto power plugs.
Loose power plugs can cause arcing or
fire.
Risk of injury or damage to the TV!
• Two people are required to lift and carry
a TV that weighs more than 25 kg or 55
lbs.
• When stand mounting the TV, use only
the supplied stand. Secure the stand to
the TV tightly. Place the TV on a flat, level
surface that can support the combined
weight of the TV and the stand.
• When wall mounting the TV, use only a
wall mount that can support the weight of
the TV. Secure the wall mount to a wall
that can support the combined weight of
the TV and wall mount.PE Electronics
Ltd. bears no responsibility
for improper wall mounting that result in
accident, injury or damage.
Risk of injury to children!
Follow these precautions to prevent the
TV from toppling over and causing injury to
children:
• Never place the TV on a surface covered
by a cloth or other material that can be
pulled away.
• Ensure that no part of the TV hangs over
the edge of the surface.
• Never place the TV on tall furniture (such
as a bookcase) without anchoring both
the furniture and TV to the wall or a
suitable support.
• Educate children about the dangers of
climbing on furniture to reach the TV.
Risk of swallowing batteries!
• The product/remote control may
contain a coin-type battery, which can be
swallowed. Keep the battery out of reach
of children at all times!
Risk of overheating!
Never install the TV in a confined space.
Always leave a space of at least 4 inches
or 10 cm around the TV for ventilation.
Ensure curtains or other objects never
cover the ventilation slots on the TV.
EN 3
Risk of damage to the TV!
• Before you connect the TV to the power
outlet, ensure that the power voltage
matches the value printed on the back
of the TV. Never connect the TV to the
power outlet if the voltage is different.
Risk of injury, fire or power cord damage!
• Never place the TV or any objects on the
power cord.
• To easily disconnect the TV power cord
from the power outlet, ensure that you
have full access to the power cord at all
times.
• When you disconnect the power cord,
always pull the plug, never the cable.
• Disconnect the TV from the power
outlet and antenna before lightning
storms. During lightning storms, never
touch any part of the TV, power cord or
antenna cable.
Risk of hearing damage!
• Avoid using earphones or headphones at
high volumes or for prolonged periods of
time.
Product disposal Guidelines:
For the purpose of recycling to facilitate effective utilization of resources, please
return this product to a nearby authorized collection center, registered dismantler,
recycler, service center when disposing of this product.
In case of further assistance, you may contact nearest authorized service center.
Or Please see the Company website for further information on collection centers etc.
Visit-http://www.philips.com
Toll :1860 200 0129
Low temperatures
• If the TV is transported in temperatures
below 5°C or 41°F, unpack the TV and
wait until the TV temperature matches
room temperature before connecting the
TV to the power outlet.
Screen care
• Avoid stationary images as much as
possible. Stationary images are images
that remain on-screen for extended
periods of time. Examples include:
on-screen menus, black bars and time
displays. If you must use stationary
images, reduce screen contrast and
brightness to avoid screen damage.
• Unplug the TV before cleaning.
• Clean the TV and frame with a soft,
damp cloth. Never use substances such as
alcohol, chemicals or household cleaners
on the TV.
• Risk of damage to the TV screen! Never
touch, push, rub or strike the screen with
any object.
• To avoid deformations and colour fading,
wipe off water drops as soon as possible.
Visit-http://www.philips.com
Toll :1860 200 0129
o
R
H
COMPLIANT
EN 4
( )
S
3 Use your TV
Congratulations on your purchase, and welcome to Philips To fully benefit from the
support that Philips offers, register your TV at www.philips.com/welcome.
3.1 Name and Function of Control on Set
(39PFL3559/V7)
A) Front Panel Control/Keys (Optional)
1) VOL+
2) VOL-
3) CH+
4) CH-
5) MENU
6) SOURCE(TV/AV)
7) STAND BY
8) IR SENSOR
9) LED INDICATOR
B) Connecting your Unit :-
Note :
1) Above Sketches are just representation. Actual TV set may look differ than
these sketches.
2) MHL are supported in HDMI 1.
3) ARC are supported in HDMI 2.
4) For source selection by controls on TV, Press TV/AV key repeatedly till you
reach to desired source In source OSD & then press VOL+ key.
1
2
3
4
5
6
7
8
9
RF IN
AV OUT
AV2 IN
R1
L1
V1
YPbPr
VGA IN
VGA AUDIO
USB 1
USB 2
HDMI 1
(MHL)
HDMI 2
(ARC)
HDMI 3
EN 5
3.2 Name and Function of Control on Remote
1
2
3
4
5
6
7
8
9
10
11
12
13
SOURCE
LIST
ADJUST
CH-
OK
TV
FORMAT
20
19
INFO
18
17
OPTIONS
CH+
16
EN 6
14
15
(Standby-On)
1
• Switches the TV ON or OFF.
The TV is not powered off completely
unless it is physically unplugged
Multimedia Control buttons
2
• Control video or music.
3
4
5
6
7
8
SOURCE
• Selects connected devices.
TV
•
Access the TV mode.
LIST
•
Access the Channel List.
(Navigation buttons)
• Navigate through menus and select
items. (Also in USB mode).
OK
• Confirm an entry or selection.
ADJUST
Access the Adjust menu to adjust settings.
•
9
Return to the previous menu or exit
•
a function.
CH - / CH +
10
•
(
Switch channels or navigate through
menu pages, tracks, albums or
folders.
Previous/Next )
15
TEXT
• Not applicable for 2100 series model’s.
16
17
18
19
20
Mute or restore audio.
•
OPTIONS
Access the option menu to adjust
•
settings.
INFO
•
Displays the source information with
details of input connected.
( Home )
• Access the home menu.
FORMAT
• Adjust picture format.
3.3 Remote control usage
When you use the remote control, hold it close
to the TV and point it at the remote control
sensor. Make sure that the line-of-sight between
the remote control and TV is not blocked by
furniture, walls or other objects.
~5m
o
~30
+/-
11
12
13
14
Adjust volume.
•
Color buttons
Select tasks or options.
•
0-9 Numeric buttons
• Select channels.
SUBTITLE
• Not Applicable for 2100 series model’s.
EN 7
3.4 Battery Installation
1. Remove the battery compartment door.
2. Install 2 “AAA” or UM-4 (1.5V) batteries or equivalent with the correct polarity
as indicated.
3. Refix the battery compartment door.
1 2 3
EN 8
4 Use more of
your TV
4.1 Main Menu
Menus help you to install channels, change
picture and sound settings and access other
TV features.
1
Press
» The menu screen appears.
2 Select one of the following, then press
OK
[Watch TV]
•
antenna is selected, switch back to
the antenna source
• [Device List]
change other source by pressing key.
Also, User can view Device List or
change the source by pressing Source
key on Remote.
•
[Setup]
picture, sound and other settings.
•
[Browse USB]:
play music and movies contained in
USB storage devices.
•
[ ]:Watch Video
Watch videos in USB mode .
•
[ ]:Listen Music
Listen music in USB mode.
•
[ ]:View Photos
View photos in USB mode.
: If a source other than
: Access menus to
: Access menus to change
View photos and
4.2 Manually adjust picture setting
Picture
Sound
Installation
Features
Parental
Picture
Picture
Picture
Sound
Sound
Sound
Features
Features
Installation
Installation
Installation
Features
Parental
1
Press .
2
Select [Setup] > [Picture] ,
then press OK or key.
3
Select one of the following settings, then
Press to move, and press to adjust.
• [Smart picture]
picture settings.
• [Contrast]
backlight areas, while the video contents
are kept unchanged.
• [Brightness]
details of dark areas.
•
[Color]
• [Sharpness]
image.
• [Hue]
• [Color Temperature]
balance in an image.
Smart Picture
Contrast
Brightness
Color
Hue
Sharpness
Hue
Color Temperature
Digital Crystal Clear
Digital Crystal Clear
Pixel Precise HD
Geometric
Geometric
: Access predefined smart
: Adjust the intensity of
: Adjust the intensity and
: Adjust color saturation.
: Adjust sharpness in the
: Compensate for color variations.
(Available only for NTSC channels).
: Adjust the color
EN 9
[Pixel Precise HD ] :
To enhance the picture quality
[Flesh Tone] : Adust Flesh tone
•
•
[Noise Reduction]: Filter and reduce noise
in an Image
[Dynamic contrast]
•
contrast.
• [Color enhancement]
colors more vivid and improve the
details in bright colors. You can
switch this feature ON or OFF.
[Geometric] :
• [Auto Setting]:This automatically adjust
H & V-position,Phase and Clock for VGA
mode.
[H-Position]
•
position of image [Only in VGA].
[V-Position]
•
•
position of image [Only in VGA].
[Phase]: If picture is not OK with Auto
•
•
Setting, then adjust by phase.
[Only in VGA].
[Manual Clock]: If picture is not OK
•
•
with Auto Setting, then adjust by manual
clock [Only in VGA].
Note
: Adjust the horizontal
: Adjust the vertical
: Enhance
: Make
Geometric options applicable only for
VGA source .
4.3 Use Smart Picture
Use smart picture to apply pre-defined
picture settings.
Smart Picture
Smart Sound
Picture Format
Freeze
Sleep Timer
Geometric
Vivid
1 Press ADJUST.
2 Select [Smart Picture], then press OK.
3 Select one of the following settings, by keys
•
[Bright]
: Ideal settings for night time.
: Rich and dynamic settings,
[Vivid]
•
ideal for daytime.
[Sport]
•
•
•
: Ideal settings for sport.
[Cinema]
[Personal]
picture settings.
: Ideal settings for movies.
.
: Apply your customized
4.4 Use Picture Format
1 Press
2 Select [Picture Format], then press OK
Select any picture format, then press OK
3
Note
Depending on the format of the picture
source, some picture settings may not be available.
ADJUST
.
EN 10
4.5 Use Freeze option
1 Press ADJUST.
2 Select [Freeze], then press OK
Select option as ON to freeze the
3
picture.
4.6 Manually adjust sound setting
Picture
Sound
Installation
Features
Parental
Picture
Sound
Installation
Features
Parental
Press
1
Select [Setup] >
2
then press
3 Select one of the following settings, then
Press to move, and press to adjust.
• [Smart Sound]
sound settings.
• [Equalizer]
various frequencies.
[Bass] :
•
[Treble] :
•
• [Balance]
and left speakers.
[Volume] : The main speaker volume can be
•
adjusted by varying this volume bar.
• [AVL] :
automatically reduces sudden
volume changes, for example when
switching channels.
[Speakers] : The main speakers can be
•
made ON / OFF by this option.
Smart Sound
Equalizer
Bass
Treble
Balance
Volume
AVL
Speakers
AV Out
AV Out Volume
.
[Sound]
OK
: Access predefined smart
: Adjust the equalizer ON
Adjust the bass level.
Adjust the treble level.
: Adjust the balance of the right
Auto volume leveler
[AV Out ]
Select Fixed for default settings and
variable to vary it.
:
[AV Out Volume] : The AV Out volume can be
adjusted by this option.
4.7 Use Smart Sound
Use smart sound to apply pre-defined
Sound settings.
Smart Picture
Smart Sound
Picture Format
Freeze
Sleep Timer
Geometric
Press ADJUST.
1
2
Select
3
Select one of the following settings, by
[Smart sound]
[Smart Sound], then press OK.
: Access predefined smart
Vivid
sound settings.
• [Standard]
: Settings that suit most
environments and types of audio.
• [Music]
• [News]
: Ideal settings for listening to music.
: Ideal settings for spoken audio,
such as news.
• [Personal]
: Apply the settings that were
customised in the sound menu.
4.8 Use Sleep Timer
Press ADJUST
1
Select
2
Press adjust the Sleep timer OFF and ON
in step of 10,20,30,60,90.120,180,240 min.
.
[Sleep Timer], then press OK.
EN 11
4.9 Installation Menu
Picture
Sound
Installation
Features
Parental
Channel No.
Skip
Program Name
Color System
Sound System
Auto Install
Manual Install
Fine Tune
Channel No.
1
2
3
4
5
6
7
8
Swap
Select
Program Edit
Freq
Name
48.25
------
83.25
------
105.25
------
169.25
------
175.25
------
203.25
------
224.25
------
463.25
------
Insert
1
2
Page
Copy
Back
Favourite
Skip
On
On
On
On
On
On
On
On
3
Delete
4
Confrim
OK
MENU
Press
1
Select [Setup] >
2
[Installation]
then press OK
3 Select one of the following settings, then
Press to move, and press to adjust.
[Channel No.] : Display the channel number of
•
the current channel.
[Skip] : Switch On to Skip selected Program
•
•
S .kipped Program can be viewed by entering
channel no.
[Program Name] : Channel naming by
•
•
Press to select letters , and press to
navigate between the character of program name.
[Color System] : Change the color system
•
(AUTO/PAL/SECAM/NTSC 3 58) setting if the
picture is not reproduced properly.
Note
For India color system is Auto or PAL.
[Sound System]
•
: Change the sound
sound system (BG/I/DK) setting if sound
is not reproduced properly.
Note
For India sound system is BG.
Swap
Move the cursor to the program to be swapped,
Select Swap option by pressing 1 button and
press to move on another program.
press OK then two program are swapped.
Insert
Move the cursor to the program to be Inserted,
Select Insert option by pressing 2 button and
press to move on another program.
press OK then Selected program are inserted.
Copy
Move the cursor to the program to be Copied,
Select Copy option by pressing 3 button and
press to move on another program.
press OK then Selected program are copied.
Delete
Move the cursor to the program to be Deleted,
Select Delete option by pressing 4 button,
are deleted. then Selected Program
Favourite List
User can prepare 4 independent favourite list.
To define favourite list, Move the cursor to the
desired program number & press Red/Green/
Yellow or Cyan color key in which you wish
to add program
To access favourite list press Red/Green/
Yellow/Cyancolor keys on remote.
[Auto Install]
:Select the function TV
set will start auto tuning for all available
channels.
[Manual Install]
:Select this for manually
searching the channels,select the function
from which tuning will start.
[Fine Tune]:
Fine tunning the channel if picture &
sound is not clear even after Auto installation.
[Program Edit]:
You can Swap, Insert, Copy
and Delete the channels.
EN 12
4.10 Features Menu
Press
1
2 Select [Setup] >
then press
3 Select one of the following settings.
then press OK. .
Press to move, and press to adjust.
Picture
Sound
Installation
Features
Parental
[Back Light] : The backlight value
can be varied . This function used to
adjust brightness level of panel.
[Blueback] :This function is used to
ON /OFF the blue screen at no signal
condition.
[Energy Saving]:
•
the power consumed by TV, select
power saving modes Off/low/Mid/ High/
Audio only Mode.
After selection of Low/Mid/high energy
saving indication displayed on energy
meter by pressing info key of remote control
Low: After selection of energy saving
option to “Low”, approx.5% of rated
power will get saved.
Mid: After selection of energy saving
option to “Mid”, approx.10% of rated
power will get saved.
High: After selection of energy saving
option to “High”, approx 25% of rated
power will get saved.
Audio only : After selection of energy
saving to “Audio only ” panel power
switched off & only audio come
from TV sets which results in
power saved of approx 35%
Note
Press any key ( except Find, Text, subtitle
Vol +/- and Mute) to exit 'Audio only' mode
[Features]
OK
Back Light
Blue Mute
Energy Saving
EasyLink
HDMI ARC
MHL
Reset
To save
[EasyLink]: If you connect HDMI-CEC
compliant devices through HDMI,you
can control them at the same time with
your TV remote control.
[HDMI ARC] : If you connect ARC enabled
•
Home Theater to TV set HDMI ARC to ON
to listen sound through Home Theater
•
[MHL] : To use MHL function set this to ON.
Note
EasyLink Applicable for only HDMI Source.
MHL is supported in HDMI 1.
ARC is supported in HDMI 2, If ARC is set to
on, TV Speaker will be disabled.
[Reset] : Reset to factory default settings.
•
4.11 Parental Menu
Picture
Sound
Installation
Features
Parental
Press
1
2 Select [Setup] > [Parental]
then press OK
3 Select one of the following settings.
then press OK.
[Child Lock]: Enter the password, then
the following menus will open.
Note: Default password is “0000”
[Child Lock Switch]:Make the child lock
switch ON to lock the source/channel.
[Video Lock]: Select the sources
with up/down keys on remote and press
OK to set or clear lock.
[Channel lock]: Select the channels to
to be locked and press OK key to lock or
unlock the channels.
[Change Password]: Select this option
to change the password.
• [Clear All]: Reset the child lock
option to default value.
Child Lock
EN 13
4.12 Use Philips EasyLink
Get the most out of your HDMI-Consumer
Electronic Control (CEC) compliant devices
with Philips EasyLink enhanced control
features.
If your HDMI-CEC compliant devices are
connected through HDMI, you can control
them at the same time with your TV remote
control.
To enable Philips EasyLink, you need to:
• Connect HDMI-CEC
compliant devices through HDMI
• Configure each HDMI-CEC compliant
device properly
• Switch on EasyLink
Note
• The EasyLink-compliant device must be
switched on and selected as the source.
• Philips does not guarantee 100%
interoperability with all HDMI CEC devices.
4.13 Switch on or off EasyLink
1 Press
2 Select [Setup] > [Features] >
[EasyLink] > [EasyLink].
3 Select [On] or [Off] , then press OK
4.14 Switch the device ON or OFF
When an HDMI-CEC compliant device
is connected and TV switches to standby,
the device gets turned OFF automatically.
1 Press
2 Select [Setup] > [Features] >
[EasyLink]
[EasyLink] > [Auto turn off] >
3 Select [On] or [Off], then press OK
When an HDMI-CEC compliant device
is connected and TV is switched ON, then
the device gets turned ON automatically.
4.15 Search the connected devices
Search the HDMI-CEC compliant devices
connected to your TV and list them using
Device list.
1 Press
2 Select [Setup] > [Features] >
[EasyLink] > [Device Search] >
4.16 Control the device using TV
remote
Now use a single remote to control your
CEC enabled device.
Note
• If EasyLink is OFF, all its submenus are
unavailable.
Easy Link
Picture
Sound
Installation
Features
Parental
EN 14
Auto turn off
Device Search
Device List
Device Menu
1 Press
2 Select [Setup] > [Features] >
[EasyLink] > [Device Menu]
Play
Pause
FR FF
Prev. Next
Stop
Press to select the function icon, press
OK button to confirm the function.
4.17 Use Geometric
Use Geometric to automatically adjust
phase and Clock for VGA mode
Smart Picture
Smart Sound
Picture Format
Freeze
Sleep Timer
Geometric
1
Press ADJUST.
Select [Geometric], then press OK.
2
This automatically adjust H & V-position,
Phase and Clock for VGA mode
4.18 Use the Options menu
Status
Energy Saving
Guide Bar
Visit options relevant to current action or
selection.
While you watch TV, press
1
OPTIONS key.
The TV options menu appears.
2 Select one of the following options, then
press OK.
• [Status]:
Display information
concerning currently viewing
channel/source.
[Energy Saving]:
Respective menu
after pressing OK.pop ups
•
Press
to conserve energy.
refer 4.10 for more details.
[Guide Bar] :
Respective menu
after pressing OK.pop ups
Press to access menu bar.
refer 5.8 for more details.
Note
Guide Bar only applicable for HDMI (CEC)
& USB Source.
EN 15
5 Play photos, music and videos
on USB storage devices
5.1 Connect a USB storage device
to play photos, music or videos
stored on it.
1 Switch on the TV.
2 Connect the USB device to the USB port
on the side of your TV.
3 Press
4 Select [Browse USB], then press OK
The USB browser appears.
5.2 View photos
1 In the Source List, select [USB]
> [Photo]
2 Select a photo or a photo album, then
OK to view the photo
• To preview the next or previous photo,
,then press OK.
press then press to play.
5.3 View a slide show of your photos
Press the following buttons to control
play of selected photo:
Select photos by OK key :
to play.
•
• to pause.
• CH+ or CH- to play the previous
or next photo.
5.4 Listen to music
In the Source List, select [USB]
1
> [Music]
2
Select a music track or album, then press
OK or to play.
To control play, press the play buttons:
3
•
•
• or to do Fast Forward and
,then press OK.
to play/pause.
CH+ or CH- to play the previous
or next photo.
Fast Reverse.
5.5 Watch video
In the Source List, select [USB]
1
> [Video]
2 Press OK or to play.
To control play, press the play buttons:
3
•
•
• or to do Fast Forward and
,then press OK.
to play & to pause.
CH+ or CH- to play the previous
or next photo.
Fast Reverse.
5.6 Text
1
In the Source List, select [USB]
,then press OK.
> [Text]
2 Select a Text File, then Press
OK or to play.
EN 16
Note
• User can directly view Photos, Music &
.
Video by selection respective option from
Main Home Page.
USB & HDD detection time may vary from
•
manufacturer to manufacturer of USB and
HDD.
5.7 Use the Options menu
Status
Energy Saving
Guide Bar
Visit options relevant to current action or
selection.
While you watch TV, press
1
OPTIONS key.
» The TV options menu appears.
2 Select one of the following options, then
press OK.
•
[Status]:
Not Applicable For USB
[Energy Saving]:
after pressing OK.pop ups
•
Press
refer 4.10 for more details.
[Guide Bar] :
after pressing OK.pop ups
Press to access menu bar.
refer 5.8 for more details.
Note
Guide Bar only applicable for HDMI (CEC)
& USB Source.
Respective menu
to conserve energy.
5.8 Music,Photo, video, text
You can select the multimedia functions
like play, Pause, FF, FR, Next, Previous,
Stop etc.
To use above functions press
OPTIONS , then select “Guide Bar”.
Music mode menu bar:
Press to select the function icon, press
OK button to confirm the function.
Video mode menu bar:
Press to select the function icon, press
OK button to confirm the function.
Text mode menu bar:
Up/Dwon
Prev/Next Page
Prev File Nex File
Press to select the function icon, press
OK button to confirm the function.
5.9 Disconnect a USB storage device
Caution
•
Follow this procedure to avoid damage to
your USB storage device.
1 Press to exit the USB browser.
2
Wait for few seconds, then disconnect
the USB storage device.
Picture mode menu bar:
EN 17
6 Troubleshooting
This section describes commonly encountered
issues and accompanying solutions.
6.2 TV channel issues
Previously installed channels do not appear in
the channel list:
Check that the correct channel list is
selected.
6.1 General TV issues
The TV does not switch on:
Disconnect the power cable from the power
outlet. Wait for one minute then reconnect it.
Check that the power cable is securely
connected.
The remote control is not working properly:
Check that the remote control batteries
are correctly inserted according to the +/orientation.
Replace the remote control batteries if they
are flat or weak.
Clean the remote control and TV sensor lens.
The standby light on the TV blinks red:
Disconnect the power cable from the power
outlet. Wait until the TV cools down before
reconnecting the power cable. If the blinking
reoccurs, contact Philips Consumer Care.
You forgot the code to unlock the TV lock feature
Enter ‘8202’.
When turning the TV on/off/to standby, you hear a
creaking sound from the TV chassis:
No action is required. The creaking sound is
normal expansion and contraction of the TV as
it cools down and warms up. This does not
impact performance.
6.3 Picture issues
The TV is on, but there is no picture:
Check that the antenna is properly
connected to the TV.
Check that the correct device is selected
as the TV source.
There is sound but no picture:
Check that the picture settings are
correctly set.
There is poor TV reception from an antenna
connection:
Check that the antenna is properly
connected to the TV.
Loudspeakers, unearthed audio devices,
neon lights, high buildings and other large
objects can influence reception quality.
If possible, try to improve the reception
quality by changing the antenna direction
or moving devices away from the TV.
If reception on only one channel is poor,
fine tune this channel.
There is poor picture quality from connected
devices:
Check that the devices are connected
properly.
Check that the picture settings are
correctly set.
The TV did not save your picture settings:
Check that the TV location is set to the
home setting. This mode offers you the
flexibility to change and save settings.
The picture does not fit the screen; it is too
big or too small:
Try using a different picture format.
The picture position is incorrect:
Picture signals from some devices may
not fit the screen correctly. Check the
signal output of the device.
EN 18
6.4 Sound issues
There is a picture but sound quality is poor:
Note
If no audio signal is detected, the TV
automatically switches the audio output off
this does not indicate malfunction.
Check that all cables are properly connected.
Check that the volume is not set to 0.
Check that the sound is not muted.
There is a picture but the sound quality is poor:
Check that the sound settings are correctly
set.
There is a picture but sound comes from one
speaker only:
Verify that sound balance is set to the centre.
6.5 HDMI connection issues
There are problems with HDMI devices:
Note that HDCP (High-bandwidth Digital
Content Protection) support can delay the
time taken for a TV to display content from
a HDMI device.
If the TV does not recognise the HDMI
device and no picture is displayed, try
switching the source from one device to
another and back again.
If there are intermittent sound disruptions,
check that output settings from the HDMI
device are correct.
If you use an HDMI-to-DVI adapter or
HDMI-to-DVI cable, check that an additional
audio cable is connected to AV IN.
6.7 ARC
ARC enables digital sound to be output using
just an HDMI cable.
How to Use ARC
Connect ARC-enabled AV receiver through
High Speed HDMI™ Cable (HDMI 1.4 cable)
to HDMI Port 2 of TV.
In “Setting” menu of TV, set "HDMI ARC"
switch to "On".
Select/Set “ARC” mode “On” in AV receiver
(For more details refer user manual of AV
receiver).
Note:-
Connect AV receiver in “HDMI 2” Port of
TV.
When ARC is "On" TV Speaker will be
deactivated.
If you disconnect ARC Home Theater then
in Setting Menu of TV,
Set "HDMI ARC" option to "Off" to activate
TV speakers .
To use ARC feature keep “Easy link”
on.
issues
6.6 Computer connection issues
The computer display on the TV is not stable:
Check that your PC uses the supported
resolution and refresh rate.
Select the “Auto Setting” function.
1. Press
2. Select [Setup] >[Picture] >[Geometric]
[Auto Setting].
EN 19
6.8 MHL
Mobile High-definition Link (MHL) is an interface
for transmitting digital audiovisual signals from
mobile phones to supported television sets.
Note that it works only for the MHL-enabled
Phones, to confirm MHL Support in your Phone
check operation manual of phone.
When Smart phone is connected through MHL
Cable Some applications can be operated by
the TV remote control.
How to Use MHL
Connect MHL enabled phone with passive
MHL cable (not supplied with set) to HDMI 1
In TV OSD Menu Go to "Settings" & Set
"MHL" option to "On" to view the phone
screen on the TV.
Note: -
MHL is supported in “HDMI 1” port of TV.
Because TV screen is wider than mobile
phone, picture quality may appear lower in TV.
Mobiles need 5 Pins MHL cable but few
mobiles needs 11 Pins MHL cable.
For better user experience /Operation ease,
user can pair Mobile with Bluetooth compatible
keyboard/mouse available in market.
Although in many handset do not need any
setting to activate MHL, additional setting may
require in some mobiles/tablets, for more
details check user manual of Mobiles/Tablets).
issues
6.9 Contact us
If you cannot resolve your problem, refer to the
FAQs for this product at www.philips.com/support.
or Contact Customer Service Center.
Warning
Do not attempt to repair the product yourself.
This may cause severe injury, irreparable
damage to your product or void your
warranty.
Note
Make a note of your TV model and serial
number before you contact Philips. These
numbers are printed on the back of the TV
and on the packaging.
EN 20
7 Product
information
Product information is subject to change
without notice. For detailed product
information, go to www.philips.com/support.
7.1 Supported display resolutions
Computer formats (HDMI)
Resolution - refresh rate:
720 x 480p - 60Hz
720 x 576p - 50Hz
1280 x 720p - 50Hz,60Hz
1920 x 1080p -50Hz,60Hz
Computer formats (VGA)
Resolution - refresh rate:
640 x 480 - 60Hz,72Hz,75Hz
800 x 600 - 56Hz,60Hz,72Hz,75Hz
1024 x768 - 60Hz,70Hz,75Hz
1280 x 1024 - 60Hz
7.3 Remote control
Type: RC-Z8091-800
Batteries: 2 x AAA (LR03 type)
7.4 Multimedia
Supported USB storage device:
(Only FAT 16 or FAT 32 USB storage
devices are supported)
Supported storage file formats:
Images : JPEG, BMP, PNG
Audio : MP3,WMA.
Text
Video :
Video Formats
Resolution - refresh rate:
720 x 480i - 60Hz
720 x 480p - 60Hz
720 x 576i - 50Hz
720 x 576p - 50Hz
1280 x 720p - 50Hz, 60Hz
1920 x 1080i - 50Hz, 60Hz
7.2 Tuner/Reception/
Transmission
Antenna input: 75ohm coaxial (IEC75)
TV system: PAL,B/G
Video playback: NTSC, SECAM, PAL
Tuner Bands: UHF, VHF
Note
1)
2) The USB features/functions may vary
names must not exceed 128
USB
file
characters.
from file to file depending on relative
information present in the file
7.5 Power
Mains power: AC 110-240V~50/60Hz
Ambient temperature: 5 to 40 degrees
Celsius
Power consumption
39PFL3559/V7: 100W
EN 21
7.6 TV mount
To wall mount the TV, kit is provided in
accessory bag along with TV set.
Warning
Follow all instructions provided with the TV
mount. PE Electronics Ltd. bears no
responsibility for improper TV
mounting that results in accident, injury or
damage.
7.7 Product specification
Design and specifications are subject to change
without notice.
39PFL3559/V7
With TV stand
Dimension(WxHxD): 900 x 599 x
172 (mm)
Weight: 8.1 kg
Without TV stand
Dimension(WxHxD): 900 x 540 x
83 (mm)
Weight: 7.7 kg
EN 22
Consumer Guidelines
1.Kindly ensure that the dealer fill out Warranty card correctly.
2.To avail the Warranty please register your product with the Philips-
• Log on to www.philips.com
OR
• Contact Philips Consumer Care Centre
3.In the unlikely event of a defect developing in the TV set contact the Philips Customer
Care Centre for obtaining warranty service and inform of the defect observed in the
set, the type no. and serial no. of the set.
4.On your lodging a complaint, a trained technician will call on you promptly. In the
event of the technician deciding that set requires attention at the service station;the
technician would arrange to get the set picked up to be delivered to service station
for further attention. “Homecalls” by the technician would however be restricted within
municipal limits of the city/town in which the set has been registered.the
Type no. Serial No. Date of Purchase
Purchased By: Name
Address:
Tel.No.
Sold by: Name
Address:
Tel.No.
Sold by(User rubber stamp)
Model no.: 39PFL3559/V7
Serial no.:
Contact Customer Service Executive at:
Toll :- 1860 200 0129
Regd Office: PE Electronics Ltd,Auto Cars Compound,Adalat Road,Aurangabad,431005.
EN 23
Front
WARRANTY
This TV receiver is covered under From whom the set has been purchased or
warranty against any defect arising out through an Authorised Service Center for
of faulty or defective material or workman warranty service. However, if the
ship for a period of 12 months from the Purchaser has to shift his residence to
date of purchase. another town on account of transfer or
other reasons, the warranty benefit will be
Should a defect develop in this set during available at the Authorised Service Center
the period of warranty,PE Electronics
Limited undertakes to get the
set repaired free of charge either
The warranty is not valid in case of any of
the following events:
The TV set is not used according to instructions given in the ‘Direction for use’
/ ‘User Manual’
Defects are caused by improper or reckless use.
Any repair work carried out by persons other than a Philips dealer or Authorised
Service Center.
Any modification or alteration of any nature made in the electrical circuitry of the set.
This Warranty Card is not completed and signed immediately on delivery of the set
by the Philips Dealer.
Fading effects and/or Ghosts (Multiple Image) in picture, if any,arising due to location
/ signal reception.
Defects due to causes beyond control like lightning, abnormal voltage, Acts of God or
while in transit to purchaser’s residence.
of that town.
(Refer Consumer Guidelines for further details)
EN 24
Back
Cover 3 Blank
1100106508
Specifications are subject to change without notice.
PHILIPS and the PHILIPS Shield Emblem are registered
trademarks of Koninklijke Philips N.V. and are used under
license from Koninklijke Philips N.V.
LED TV 39”
Rev.00 Rajmudra
Loading...