All rights reserved. Specifications are subject to change without notice. Trademarks are the
property of Koninklijke Philips Electronics N.V. or their respective owners.
TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust
earlier supplies accordingly.
PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
All rights reserved. Specifications are subject to change without notice. Trademarks are the
property of Koninklijke Philips Electronics N.V. or their respective owners.
TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust
earlier supplies accordingly.
PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
2017-March-10
Page 3
1. Product information
1.1 Product Fiche
32PHx5301
• Energy Efficiency Class : A+
• Visible Screen Size : 80 cm / 32 inch
• On Mode Power Consumption (W) : 47 W
• Annual Energy Consumption (kWh) * : 68 kWh
• Standby Power Consumption (W) **: 0.30 W
• Display Resolution (Pixels) : 1366 x 768p
43PFx5301
• Energy Efficiency Class : A++
• Visible Screen Size : 108 cm / 43 inch
• On Mode Power Consumption (W) : 34 W
• Annual Energy Consumption (kWh) * : 50 kWh
• Standby Power Consumption (W) **: 0.30 W
• Display Resolution (Pixels) : 1920 x 1080p
49PFx5301
• Energy Efficiency Class : A++
• Visible Screen Size : 123 cm / 49 inch
• On Mode Power Consumption (W) : 37 W
•Annual Energy Consumption (kWh) * : 54 kWh
• Standby Power Consumption (W) **: 0.30 W
•Display Resolution (Pixels) : 1920 x 1080p
* Energy consumption kWh per year, based on the power consumption of the television operating 4 hours per day for
365 days. The actual energy consumption depends on how the television is used.
** When the TV is turned off with the remote control and no function is active.
1.2 Power
Product specifications are subject to change without notice. For more specification details of this product, see
www.philips.com/support
• Mains power : AC 220-240V +/-10%
• Ambient temperature : 5°C to 35°C
• Power saving features : Eco mode, Picture mute (for radio), Auto switch-off timer, Eco settings menu.
For power consumption information, see chapter Product Fiche.
The power rating stated on the product typeplate is the power consumption for this product during normal household
use (IEC 62087 Ed.2). The maximum power rating, stated between brackets, is used for electrical safety (IEC
60065Ed. 7.2
1.3 Reception
• Aerial input : 75 ohm coaxial (IEC75)
• Tuner bands : Hyperband, S-Channel, UHF, VHF
• DVB : DVB-T2, DVB-C (cable) QAM
• Analogue video playback : SECAM, PAL
• Digital video playback : MPEG2 SD/HD (ISO/IEC 13818-2), MPEG4 SD/HD (ISO/IEC 14496-10)
• Digital audio playback (ISO/IEC 13818-3)
• Satellite aerial input : 75 ohm F-type
• Input frequency range : 950 to 2150MHz
• Input level range : 25 to 65 dBm
• DVB-S/S2 QPSK, symbol rate 2 to 45M symbols,
Page 4
SCPC and MCPC
•LNB : DiSEqC 1.0, 1 to 4 LNBs supported, Polarity selection 14/18V, Band selection 22kHz, Tone burstmode, LNB
– Character encodings : UTF-8, Central Europe and Eastern Europe (Windows-1250), Cyrillic (Windows-1251), Greek
(Windows-1253), Turkish (Windows-1254), Western Europe (Windows-1252)
• Image Codecs : JPEG
• Limitations :
– Maximum supported total bit rate for a media file is 30Mbps.
– Maximum supported video bit rate for a media file is 20Mbps.
– MPEG-4 AVC (H.264) is supported up to High Profile @ L4.1.
– VC-1 is supported up to Advanced Profile @ L3. Wi-Fi Certified
This TV supports Miracast certified devices. Supported media server software (DMS)
•You can use any DLNA V1.5 certified media server software (DMS class).
• You can use the Philips TV Remote app (iOS and Android) on mobile devices. Performance may vary, depending on
the capabilities of the mobile device and the software used.
ESD regulations
This apparatus meets performance criteria A for ESD. In case the apparatus does not recover in file sharing mode due
to electrostatic discharge, user interference
Page 6
2. Connections Overview
Page 7
3. Mechanical Instructions
3.1 Cable Dressing
Cable dressing (32" 5302 series)
Cable dressing (43" 5302 series)
Page 8
Cable dressing (49" 5302 series)
3.2 Assembly/Panel Removal
Instructions below apply to the 32PHS5302/12, but will be similar for other 32"/43"/49"Pxx5302 series models.
3.2.1 Stand removal
1. Remove the fixation screws [1] that secure the stand
2. Take the stand bracket out from the set.
3.2.2 Rear Cover
Warning: Disconnect the mains power cord before removing the rear cover.
1. Remove fixation screws [2] and [3] that secure the Rear Cover
2. Unplug the connector [4] from SSB.
3. Gently lift the rear cover from the TV. Make sure that wires and cables are not damaged while lifting the rear cover from the set
Page 9
Rear cover removal[1]
Rear cover removal[2]
3.2.3 Keyboard Control Unit
1. Release the connector [2] from the SSB Board.
Caution: be careful, the Keyboard is catch on the Back cover, please be careful to avoid damage the fragile connectors!
2. Remove all the fixation screws from the keyboard control panel [1] and take it out from the Back cover
When defective, replace the whole unit.
Page 10
3.2.4 Small Signal Board (SSB)
Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the
SSB.
1. Release the clips from the LVDS connector that connect with the SSB[1].
Caution: be careful, as these are very fragile connectors!
1. Unplug all other connectors [2] .
3. Remove all the fixation screws from the SSB [3].
4. The SSB can now be shifted from side connector cover, then lifted and taken out of the I/O bracket.
3.2.5 Power Supply Unit (PSU)
Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the
PSU.
1. Gently unplug all connectors from the PSU.
2. Remove all fixation screws from the PSU.
3. The PSU can be taken out of the set now.
Page 11
3.2.6 IR board Control Unit
1. Unplug the connector from the SSB.
Caution: be careful, as these are very fragile connectors!
3. Remove all the fixation screws [1], [2] and connector [3] from the IR board control unit.
3. Remove the IR lens [4], IR board [5] from the DECO_REAR_COVER.
When defective, replace the whole unit.
3.2.7 Speakers
1. Gently release the tapes that secure the speaker cables.
2. Unplug the speaker connector from the SSB.
3. Take the speakers out.
When defective, replace the both units.
3.2.8 WIFI module
1. Unplug the connector from the SSB..
2. Remove fixation screw that secure the WIFI module, When defective, replace the whole unit.
3.2.9 LCD Panel
1. Remove the SSB as described earlier.
2. Remove the PSU as described earlier.
3. Remove the keyboard control panel as described earlier.
4. Remove the stand bracket as described earlier.
5. Remove the IR/LED as described earlier.
6. Remove the fixations screws that fix the metal clamps to the front bezel. Take out those clamps.
7. Remove all other metal parts not belonging to the panel.
8. Lift the LCD Panel from the bezel.
When defective, replace the whole unit.
Page 12
4. Service Modes
4.1 Service Modes
The Service Mode feature is split into following parts:
Service Alignment Mode (SAM).
Factory Mode.
Customer Service Mode (CSM).SAM and the Factory mode offer features, which can be used by the Service engineer to repair/align a TV set.
SAM and the Factory mode offer features, which can be used by the Service engineer to repair/align a TV set. Some features are:
Make alignments (e.g. White Tone), reset the error buffer(SAM and Factory Mode).
Display information (“SAM” indication in upper right corner of screen, error buffer, software version, operating hours,options and option codes,
sub menus).
The CSM is a Service Mode that can be enabled by the consumer. The CSM displays diagnosis information, which the customer can forward to the
dealer or call centre. In CSM mode, “CSM”, is displayed in the top right corner of the screen. The information provided in CSM and the purpose of
CSM is to:
Increase the home repair hit rate.
Decrease the number of nuisance calls.
Solved customers’ problem without home visit.
Note: For the new model range, a new remote control (RC) is used with some renamed buttons. This has an impact on the activation of the Service
modes. For instance the old “MENU” button is now called “HOME” (or is indicated by a “house” icon).
4.2 Service Alignment Mode (SAM)
Purpose
To modify the NVM.
To display/clear the error code buffer.
To perform alignments.
Specifications
Operation hours counter (maximum five digits displayed).
Software version, error codes, and option settings display.
Error buffer clearing.
Option settings.
Software alignments (White Tone).
NVM Editor.
Set screen mode to full screen (all content is visible).
How to Activate SAM
To activate SAM, use one of the following methods:
Press the following key sequence on the remote control transmitter: “062596”, directly followed by the “INFO/OK” button. Do not allow the
display to time out between entries while keying the sequence.
Or via ComPair.
After entering SAM, the following items are displayed,
with “SAM” in the upper right corner of the screen to indicate that the television is in Service Alignment Mode.
How to Navigate
In the SAM menu, select menu items with the UP/DOWN keys on the remote control transmitter. The selected item will be indicated. When not
all menu items fit on the screen, use the UP/DOWN keys to display the next/previous menu items.
Page 13
With the “LEFT/RIGHT” keys, it is possible to:
– (De) activate the selected menu item.
– (De) activate the selected sub menu.
– Change the value of the selected menu item.
When you press the MENU button once while in top level SAM, the set will switch to the normal user menu (with the SAM mode still active in the
background).
How to Store SAM Settings
To store the settings changed in SAM mode (except the RGB Align settings), leave the top level SAM menu by using the POWER button on the
remote control transmitter or the television set. The mentioned exceptions must be stored separately via the STORE button.
How to Exit SAM
Use one of the following methods:
Switch the set to STANDBY by pressing the mains button on the remote control transmitter or the television set.
Via a standard RC-transmitter, key in “00” sequence.
Note: When the TV is switched “off” by a power interrupt while in SAM, the TV will show up in “normal operation mode” as soon as the power is
supplied again. The error buffer will not be cleared.
SAM mode overview
4.3 Factory mode:
Purpose
To perform extended alignments.
Specifications
Displaying and or changing Panel ID information.
Displaying and or changing Tuner ID information.
Error buffer clearing.
Various software alignment settings.
Testpattern displaying.
Public Broadcasting Service password Reset.
etc.
How to Activate the Factory mode
To activate the Factory mode, use the following method:
Page 14
Press the following key sequence on the remote control transmitter: from the “menu/home” press “1999”, directly followed by the
“Back/Return” button. Do not allow the display to time out between entries while keying the sequence.
After entering the Factory mode, we can see many items displayed,use the UP/DOWN keys to display the next/previous menu items
Factory mode overview
How to Exit the Factory mode
Use one of the following methods:
Select EXIT_FACTORY from the menu and press the “OK” button.
Note: When the TV is switched “off” by a power interrupt, or normal switch to “stand-by” while in the factory mode, the TV will show up in “normal
operation mode” as soon as the power is supplied again. The error buffer will not be cleared.
4.4 Customer Service Mode (CSM)
Purpose
The Customer Service Mode shows error codes and information on the TVs operation settings.The call centre can instruct the customer (by
telephone) to enter CSM in order to identify the status of the set.This helps the call centre to diagnose problems and failures in the TV set before
making a service call.
The CSM is a read-only mode; therefore, modifications are not possible in this mode.
Specifications
Ignore “Service unfriendly modes”.
Line number for every
line (to make CSM language independent).
Set the screen mode to full
screen (all contents on screen is visible).
After leaving the Customer Service Mode, the original settings are restored.
Possibility to use “CH+” or “CH-” for channel surfing, or enter the specific channel number on the RC.
How to Activate CSM
To activate CSM, press the following key sequence on a standard remote control transmitter: “123654” (do not allow the display to time out
between entries while keying the sequence). After entering the Customer Service Mode, the following items are displayed. use the Right/Left keys
to display the next/previous menu items
Note: Activation of the CSM is only possible if there is no (user) menu on the screen!
Page 15
CSM Overview
How to Navigate
By means of the “CURSOR-DOWN/UP” knob (or the scroll wheel) on the RC-transmitter, can be navigated through the menus.
How to Exit CSM
To exit CSM, use one of the following methods.
Press the MENU/HOME button on the remote control transmitter.
Press the POWER button on the remote control transmitter.
Press the POWER button on the television set.
Page 16
5. Software Upgrading, Error code and Panel Code
5.1 Software Upgrading
Step 1: Ready for F/W Upgrade
1. Rename the software as “autorun.upg”
2.
Prepare a USB memory.
3. Copy the software to USB flash disk(root directory).
Note the version of this F/W before you change the software file name.
Step 2: F/W Upgrade
1. Plug the USB memory on the USB port on the side I/O port of TV (Please connect to USB 2.0 port, not recommend USB3.0 port)
2.
AC on (Power plug)
3. TV will upgrade automatically as detect the software
Page 17
4. Press OK to start software upgrade
5. Upgrade in progress
Page 18
Step 3: Check the SW version
1. After burning software, TV will restart
2.
Press “Menu+1999+back”, enter Factory mode to check if the software version is correct
Caution: Please make sure that software upgrade is finished before unplug the USB and AC power!
5.2 Error Code
5.2.1 Introduction
Error codes are required to indicate failures in the TV set. In principle a unique error code is available for every:
• Activated (SW) protection.
• Failing I2C device.
• General I2C error.
The last five errors, stored in the NVM, are shown in the Service menu’s. This is called the error buffer.
The error code buffer contains all errors detected since the last time the buffer was erased. The buffer is written from left to right. When an error occurs that
is not yet in the error code buffer, it is displayed at the left side and all other errors shift one position to the right.
An error will be added to the buffer if this error differs from any error in the buffer. The last found error is displayed on the left.
An error with a designated error code never leads to a deadlock situation. It must always be diagnosable (e.g. error buffer via OSD or blinking LED).
In case a failure identified by an error code automatically results in other error codes (cause and effect), only the error code of the MAIN failure is displayed.
5.2.2 How to Read the Error Buffer
You can read the error buffer in three ways:
• On screen via the SAM/CSM (if you have a picture).
Example:
– ERROR: 000 000 000 000 000: No errors detected
– ERROR: 013 000 000 000 000: Error code 13 is the last and only detected error
– ERROR: 034 013 000 000 000: Error code 13 was detected first and error code 34 is the last detected (newest) error
• Via the blinking LED procedure (when you have no picture).
5.2.3 Error codes overview
In this chassis only “layer 2” error codes are available and point to problems on the SSB. They are triggered by LED blinking
when CSM is activated. Only the following layer 2 errors are defined:
Page 19
5.2.4 How to Clear the Error Buffer
The error code buffer is cleared in the following cases:
• By using the CLEAR command in the SAM menu
• By using the CLEAR command in the Factory mode:
• By using the following key sequence on the remote control transmitter: “062599” directly followed by the OK button.
• If the contents of the error buffer have not changed for 50 hours, the error buffer resets automatically.
Note: If you exit SAM by disconnecting the mains from the television set, the error buffer is not reset.
5.3 Panel Code
Press the following key sequence on a standard RC transmitter: “062598” directly followed by MENU and “xxx”, where “xxx” is a 3 digit decimal value
of the panel type: see column “Display Code” in below tab. After resetting the Display Code, restart the set immediately.
CTN_ALT BOM# Panel Type Display Code
32PHS5302/12 TPT315B5-DXYSGA.G S6A 205
32PHS5302/12 TPT315B5-DXYSHA.G S3A 206
32PHT5302/12 TPT315B5-DXYSGA.G S6A 205
32PHT5302/12 TPT315B5-DXYSHA.G S3A 206
43PFS5302/12 TPT430H3-DUYSHA.G S1BP 238
43PFT5302/12 TPT430H3-DUYSHA.G S1BP 238
49PFS5302/12 TPT490F2-FHBN0.K S8940J 204
49PFS5302/12 TPT490F2-FHBN0.K S8940J 204
Page 20
6.Circuit Descriptions
6.1 Introduction
The TPM17.2E LA is a new chassis launched in Europe in 2017. The whole range is covered by MT5800 platform. The major deltas versus its predecessor
support DVB-T/C; DVB T2; DVB S2,WIFI/ multi-media, Video out function.
The TPM17.2E LA chassis comes with the following stylings:
All power supplies are a black box for Service. When defective, a new board must be ordered and the defective one must be returned, unless the main fuse
of the board is broken. Always replace a defective fuse with one with the correct specifications! This part is available in the regular market.
Consult the Philips Service web portal for the order codes of the boards.
Important delta’s with the platform are:
• New power architecture for LED backlight
• “Boost”-signal is now a PWM-signal + continuous variable
The control signals are:
• Stand-by
• Lamp “on/off”
• DIM (PWM) (not for PSDL)
In this manual, no detailed information is available because of design protection issues.
• +5.2V output (standby mode) for 715G7734P
• +12V output (standby mode) for 715G7574P
• +12 output (on-mode)
• +12V_audio (audio AMP power)
• Output to the display; in case of
- IPB: High voltage to the LCD panel
- PSL and PSLS (LED-driver outputs)
- PSDL (high frequent) AC-current.
6.2.2 Diversity
The diversity in power supply units is mainly determined by the diversity in displays.
The following displays can be distinguished:
• CCFL/EEFL backlight: power panel is conventional IPB
• LED backlight:
Page 22
- side-view LED without scanning: PSL power panel
- side-view LED with scanning: PSLS power panel
- direct-view LED without 2D-dimming: PSL power panel
- direct-view LED with 2D-dimming: PSDL power panel.
PSL stands for Power Supply with integrated LED-drivers.
PSLS stands for a Power Supply with integrated LED-drivers with added Scanning functionality (added microcontroller).
PSDL stands for a Power Supply for Direct-view LED backlight with 2D-dimming.
6.3 DC/DC Converters
The on-board DC/DC converters deliver the following voltages(depending on set execution):
• STB_PWR, permanent voltage for the Stand-by Power system and WIFI
• ++3V3SB,voltage for scaler,IR/LED reciver,Key board
• +12V, input from the power supply for the panel common(active mode)
• LBN power, input from the power supply for LNB supply
• LDO_PWR,DVDD3V3, voltage for EMMC when TV on
• VCCK, voltage for DDR when TV on
• AVD3V3,AVDD1V0, supply voltage for scaler MT5593
• +5V_SW, input intermediate supply voltage for USB Power/SPDIF/CI
• +3V3_TUNER, supply voltage for tuner
• DVDD3V3, voltage for IC MT5800/EMMC when TV on
•PVDD from the power +12V_AU for the AUDIO AMP
•+1.2V_T2, +3.3VA_T2 voltage for Demodulator IC channel decoder.Wi-Fi_VCC,voltage for WIFI
•+1.8V, voltage for EMMC when TV on
•Wi-Fi_VCC, voltage for WIFI
6.3.1 Power tree
Page 23
6.3.2 Power layout SSB
Power SSB Top View
Page 24
Power SSB Bottom View
6.4 Front-End Analogue and DVB-T, DVB-C;ISDB-T reception
6.4.1 DVB-C part
The Front-End for analogue tuner consist of the following key components:
• TUNER EUROPE ST42CS-2-E
• SCALER MT5800WUEJ BGA-597 Processor
Below find a block diagram of the front-end application for DVB-C part.
6.4.2 DTB-T2 part
The Front-End for DVT part consist of the following key components:
• TUNER EUROPE ST42CS-2-E
• SCALER MT5800WUEJ BGA-597 Processor
• DEMODULATOR SI2169-C50-GM
Page 25
Below find a block diagram of the front-end application for DTV part.
6.4.3 Front-End DTV-S2 reception
The Front-End for ISTB part consist of the following key components:
• TUNER EUROPE ST42CS-2-E
• SCALER MT5800WUEJ BGA-597 Processor
• DEMODULATOR Si2166-C50-GMR QFN48
Below find a block diagram of the front-end application for DTV part.
6.5 HDMI
Refer to belowfor the application.
The following HDMI connector can be used:
• HDMI 1: HDMI input ( TV digital interface support HDMI1.4/HDCP1.3) with digital audio/PC DVI input/ARC
• HDMI 2: HDMI input ( TV digital interface support HDMI1.4/HDCP1.3) with digital audio/PC DVI input/ARC
• +5V detection mechanism
• Stable clock detection mechanism
• HPD control
• Sync detection
• Audio return channel(ARC)
• TMDS output control
• MHL control
Page 26
• CEC control
6.6 Video and Audio Processing – MT5800WUEJBGA
The MT5800WUEJ BGA-597 is the main audio and videoprocessor (or System-on-Chip)for this platform. It has the following features:
• Worldwide multi-standard analog TV demodulator
• DVB-T/DVB-C demodulators
• Powerful quad core CPU
• 3D graphic support OpenGL ES 2.0
• A muti-standard video decoder
• A transport de-multiplexer
• Rich format audio codec
• H.264 encoder
• 2D/3D converter
• HDMI 1.4a receiver with 3D support
• Local dimming (LED backlight)
• Ethernet MAC+PHY
• MHL 2.0 & Standby Charging
• Panel overdrive control
• Two-link LVDS, mini-LVDS, V-by-one, EPI
The MediaTek MT5800WUEJ family consists of a DTV front-end demodulator, a backend decoder and a TV controller and offers high integration for
advanced applications. It integrates a transport de-multiplexer, a high definition video decoder, an audio decoder, a two-link LVDS transmitter, a mini-LVDS
transmitter, a V-by-One transmitter, an EPI transmitter, and an NTSC/PAL/SECAM TV decoder with a 3D combfilter (NTSC/PAL). The MT5800WUEJ
enables consumer electronics manufacturers to build high quality, low cost and feature-rich DTV.World-Leading Audio/Video Technology.
The MT5800WUEJ supports Full-HDMPEG1/2/4/H.264/HEVC(H.265)/MVC/DiviX/Xvid/VC1/RM/AVS/AVS+/VP8/VP9 video decoder standards, and
JPEG. The MT5800WUEJ also supports MediaTek MDDiTM de-interlace solution which can reach very smooth picture quality for motions.A 3D comb filter
added to the TV decoder recovers great details for still pictures. The special color processing technology provides a natural, deep colors and true studio
quality video. Moreover, the MT5800WUEJ family has built-in high resolution and high-quality audio codec.Rich Features for High Value Products.
The MT5800WUEJ family enables true singlechip experience. It integrates high-quality HDMI1.4a,high speed VGA ADC, two-link LVDS, mini-LVDS ,
V-by-One, EPI, USB2.0 receiver, Ethernet MAC+PHY, quad core CPU and 512K bytes L2 cache, TCON, panel overdrive, OpenGL ES 1.1/2.0, OpenVG
1.1 compliant 3D graphic engine, and /DVB-T/DVB-C demodulators.WW Common Platform Capability: The MT5800WUEJ family supports DVB-T, DVB-C
demodulation functions. It reserves transport stream inputs for external demodulators for other countries or areas. TV maker can easily port the same UI to
worldwide TV models. First-class adjacent and co-channel rejection capability grants excellent reception. Professional error concealment provides stable,