Philips 32PFL4208S/98, 39PFL4208S/98, 42PFL4208S/98, 46PFL4208S/98 User Manual

Register your product and get support at

www.philips.com/welcome

PFL4208D
PFL4208S

EN User Manual

Contents

1 Important 3

Safety 3
Care 4
Legal 5
Sustainability 7
Help and support 8

2 Use your TV 9

TV controls 9
Watch TV 11
View program guide 14
Play multimedia files 15
Smart TV 18
Interactive TV 20

3 Use more of your TV 21

Pause TV 21
Record TV shows 22
Use Skype™ 25
Play games 28
View Teletext 29
Set locks and timers 30

4 Change your TV settings 32

Picture and sound 32
Channels 34
Language settings 36
Universal access settings 37
Other settings 38
Update software 39
Reset all 40

5 Connect your TV 41

Connection issues 58
Network issues 59
Contact Philips 59

7 Specifications 60

Power and reception 60
Display and sound 60
Display resolutions 60
Multimedia 60
Connectivity 63
Help version 63

8 Index 64

About cables 41
Connect antenna 42
Connect devices 42
Connect more devices 48
Watch connected devices 50
Set up EasyLink devices 50
Connect to a network and the Internet
53

6 Troubleshooting 56

General issues 56
Channel issues 57
Picture issues 57
Sound issues 58

EN 2

1 Important

Safety

Precautions

Read and understand all instructions before
you use your TV. If damage is caused by
failure to follow the instructions, the
warranty does not apply.

Risk of electric shock or fire!

 Never expose the TV to rain or water.

Never place liquid containers, such as
vases, near the TV. If liquids are spilled
on or into the TV, disconnect the TV
from the power outlet immediately.
Contact Philips Consumer Care to have
the TV checked before use.

 Never place the TV, remote control or

batteries near naked flames or other
heat sources, including direct sunlight.
To prevent the spread of fire, keep
candles or other flames away from the
TV, remote control and batteries at all
times.

 Never insert objects into the ventilation

slots or other openings on the TV.

 Never expose the remote control or

batteries to rain, water or excessive
heat.

 Avoid force coming onto power plugs.

Ensure that the power plug is fully
inserted into the power socket. Loose
power plugs can cause arcing or fire.

 When the TV is swiveled, ensure that

no strain is exerted on the power cord.
Strain on the power cord can loosen
connections and cause arcing.

 To disconnect the TV from the mains

power, the power plug of the TV must
be disconnected. When disconnecting
the power, always pull the power plug,
never the cord. Ensure that you have

English

full access to the power plug, power
cord and outlet socket at all times.

Risk of damage to the TV!

 Two people are required to lift and

carry a TV that weighs more than 25kg
or 55lbs.

 When stand mounting the TV, use only

the supplied stand. Secure the stand to
the TV tightly. Place the TV on a flat,
level surface that can support the
combined weight of the TV and the
stand.

 When wall mounting the TV, use only a

wall mount that can support the weight
of the TV. Secure the wall mount to a
wall that can support the combined
weight of the TV and wall mount. TP
Vision Netherlands B.V. bears no
responsibility for improper wall
mounting that results in accident, injury
or damage.

 If you need to store the TV,

disassemble the stand from the TV.
Never lie the TV on its back with the
stand installed.

 Before you connect the TV to the

power outlet, ensure that the power
voltage matches the value printed on
the back of the TV. Never connect the
TV to the power outlet if the voltage is
different.

 Parts of this product can be made of

glass. Handle with care to avoid injury
and damage.

Risk of injury to children!
Follow these precautions to prevent the TV
from toppling over and causing injury to
children:

 Never place the TV on a surface

covered by a cloth or other material
that can be pulled away.

 Ensure that no part of the TV hangs

over the edge of the surface.

EN 3

 Never place the TV on tall furniture,

such as a bookcase, without anchoring
both the furniture and TV to the wall
or a suitable support.

 Educate children about the dangers of

climbing on furniture to reach the TV.

Risk of swallowing batteries!

 The product/remote control may

contain a coin type battery, which can
be swallowed. Keep the battery out of
reach of children at all times!

Risk of overheating!

 Never install the TV in a confined

space. Always leave a space of at least 4
inches or 10 cm around the TV for
ventilation. Ensure that curtains or
other objects never cover the
ventilation slots on the TV.

Risk of injury, fire or power cord damage!

 Never place the TV or any objects on

the power cord.

 Disconnect the TV from the power

outlet and aerial before lightning
storms. During lightning storms, never
touch any part of the TV, power cord
or aerial cable.

Risk of hearing damage!

 Avoid using earphones or headphones

at high volumes or for prolonged
periods of time.

Low temperatures

 If the TV is transported in temperatures

below 5°C or 41°F, unpack the TV and
wait until the TV temperature matches
room temperature before connecting
the TV to the power outlet.

Care

Screen

 Risk of damage to the TV screen!

Never touch, push, rub or strike the
screen with any object.

 Unplug the TV before cleaning.
 Clean the TV and frame with a soft

damp cloth and wipe gently. Never use
substances such as alcohol, chemicals or
household cleaners on the TV.

 To avoid deformations and color fading,

wipe off water drops as soon as
possible.

 Avoid stationary images as much as

possible. Stationary images are images
that remain onscreen for extended
periods of time. Stationary images
include onscreen menus, black bars,
time displays, etc. If you must use
stationary images, reduce screen
contrast and brightness to avoid screen
damage.

Placement tips

 Position the TV where light does not

shine directly on the screen.

 The ideal viewing distance of this TV is

three times its diagonal screen size. For
example, if the diagonal screen size of
the TV is 81cm / 32", the ideal viewing
distance is ~2.5m / ~92" from the front
of the screen.

 While seated, your eyes should be level

with the center of the screen.

TV placement
You can apply the best sound settings for
your TV by selecting the TV placement (wall
mount or stand mount).

1. Press

2. Select [Setup], then press OK.

3. Select [TV settings] > [General settings]
> [TV placement].

4. Select [On a TV stand] or [Wall
mounted], then press OK.

.

EN 4

Lock the TV

Your TV is equipped with a Kensington
security slot at the base of the TV. To secure
the TV, purchase a Kensington anti-theft lock
(sold separately).

Legal

Notice

2013 © TP Vision Netherlands B.V. All rights
reserved. Specifications are subject to change
without notice. Trademarks are the property
of Koninklijke Philips Electronics N.V or their
respective owners. TP Vision Netherlands
B.V. reserves the right to change products at
any time without being obliged to adjust
earlier supplies accordingly.

The material in this manual is believed
adequate for the intended use of the system.
If the product, or its individual modules or
procedures, are used for purposes other
than those specified herein, confirmation of
their validity and suitability must be obtained.
TP Vision Netherlands B.V. warrants that the
material itself does not infringe any United
States patents. No further warranty is
expressed or implied.

TP Vision Netherlands B.V. cannot be held
responsible neither for any errors in the
content of this document nor for any
problems as a result of the content in this
document. Errors reported to Philips will be

English

adapted and published on the Philips support
website as soon as possible.

Terms of warranty

 Risk of injury, damage to TV or void of

warranty! Never attempt to repair the
TV yourself.

 Use the TV and accessories only as

intended by the manufacturer.

 The caution sign printed on the back of

the TV indicates risk of electric shock.
Never remove the TV cover. Always
contact Philips Customer Care for
service or repairs.

 Any operation expressly prohibited in

this manual, or any adjustments and
assembly procedures not
recommended or authorized in this
manual shall void the warranty.

Pixel characteristics
This LCD/LED product has a high number of
color pixels. Although it has effective pixels
of 99.999% or more, black dots or bright
points of light (red, green or blue) may
appear constantly on the screen. This is a
structural property of the display (within
common industry standards) and is not a
malfunction.

EN 5

Open source

This product contains software licensed
under an open source license. For
acknowledgments and license texts, please
refer to the electronic in-product user
manual. TP Vision Netherlands B.V. hereby
offers to deliver, upon request, a copy of the
complete corresponding source code for the
copyrighted open source software packages
used in this product for which such offer is
requested by the respective licenses.

This offer is valid up to three years after
product purchase to anyone in receipt of this
information. To obtain source code, please
send your request in English with product
number to:

“Intellectual Property Department, TP Vision
Netherlands B.V., Prins Bernhardplein 200 ­Floor 8, 1097 JB Amsterdam, The
Netherlands”.

Trademarks and copyrights

Windows Media is either a registered
trademark or trademark of Microsoft
Corporation in the United States and/or
other countries.

®

Manufactured under license from Dolby
Laboratories. Dolby and the double-D
symbol are trademarks of Dolby
Laboratories.

The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI Logo
are trademarks or registered trademarks of
HDMI Licensing LLC in the United States
and other countries.

Kensington and Micro Saver are registered
US trademarks of ACCO World
Corporation with issued registrations and
pending applications in other countries
throughout the world.

®

DLNA

, the DLNA Logo and DLNA

®

CERTIFIED

are trademarks, service marks,
or certification marks of the Digital Living
Network Alliance.

Covered by one or more of the following
U.S. patents: 7,295,673; 7,460,668;
7,515,710; 7,519,274.

®

DivX

, DivX Certified® and associated logos
are trademarks of Rovi Corporation or its
subsidiaries and are used under license.

DivX Certified® to play DivX® video up to
HD 1080p, including premium content.

ABOUT DIVX VIDEO: DivX

®

is a digital
video format created by DivX, LLC, a
subsidiary of Rovi Corporation. This is an
official DivX Certified

®

device that plays
DivX video. Visit divx.com for more
information and software tools to convert
your files into DivX videos.

ABOUT DIVX VIDEO-ON-DEMAND: This
DivX Certified

®

device must be registered in
order to play purchased DivX Video-on­Demand (VOD) movies. To obtain your
registration code, locate the DivX VOD
section in your device setup menu. Go to
vod.divx.com for more information on how
to complete your registration.

Skype is a trademark of Skype Limited or its
related companies.

EN 6

PlayReady Final Products

™

Content owners use Microsoft PlayReady
content access technology to protect their
intellectual property, including copyrighted
content. This device uses PlayReady
technology to access PlayReady protected
content and/or WMDRM-protected content.
If the device fails to properly enforce
restrictions on content usage, content
owners may require Microsoft to revoke the
device’s ability to consume PlayReady­protected content. Revocation should not
affect unprotected content or content
protected by other content access
technologies. Content owners may require
you to upgrade PlayReady to access their
content. If you decline an upgrade, you will
not be able to access content that requires
the upgrade.

All other registered and unregistered
trademarks are the property of their
respective owners.

 Switch off inactive devices: Switch off

connected EasyLink HDMI-CEC
(Consumer Electronic Control)
compliant devices that are inactive.
While you watch TV, press the Green
button and select [Inactive devices off].

 Power management: An advanced

power management helps save the
energy consumed by this TV. To view
how your personalized TV settings
affect the TV's relative power
consumption, press , then select

[Setup] > [Watch demos] > [Active
Control demo].

Recycling

Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.

English

Sustainability

Energy efficiency

This TV is designed with energy-efficient
features. To access these features, press the
Green button on the remote control.

 Energy saving picture settings: You can

apply a combination of energy saving
picture settings. While you watch TV,
press the Green button and select

[Energy saving]. Then select the
[Energy saving] picture setting.

 Screen off: If you only want to listen to

audio from the TV, you can switch off
the TV display. Other functions
continue to operate normally. While
you watch TV, press the Green button
and select [Screen off].

 Auto switch off: To conserve energy,

set the TV to switch off automatically
after a period of inactivity. While you
watch TV, press the Green button and
select [Auto switch off]. Then select
the period after which the TV switches
off.

When this crossed-out wheeled bin symbol
is attached to a product it means that the
product is covered by the European
Directive 2002/96/EC. Please inform yourself
about the local separate collection system
for electrical and electronic products.

EN 7

Please act according to your local rules and
do not dispose of your old products with
your normal household waste. Correct
disposal of your old product helps to
prevent potential negative consequences for
the environment and human health.

Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste. Please inform yourself about the local
rules on separate collection of batteries
because correct disposal helps to prevent
negative consequences for the
environmental and human health.

Use the Philips connectivity guide

An easy-to-use connectivity guide gives you
guidance on how to connect your TV to
other devices. Visit

http://www.connectivityguide.philips.com.

Search the TV forum

Your question may have already been
answered by the Philips TV community of
users. Visit www.supportforum.philips.com.

Contact Philips

You can contact Philips Consumer Care in
your country for support. The number is
available in the leaflet accompanying this
product, or online at

www.philips.com/support.

Before you contact Philips, write down the
model and serial number of your TV. You
can find this information on the back of your
TV or on the TV packaging.

Help and support

Use Help

To access the onscreen [Help] menu, press
the Blue button.

To exit from the [Help] menu, press

Visit Philips website

If you can't find what you need in the
onscreen [Help], visit the Philips support
website at www.philips.com/support.

At the Philips support website, you can also:

 Find answers to Frequently Asked

Questions (FAQ)

 Download a printable PDF version of

this user manual

 Email us a specific question
 Chat online with Philips Consumer

Care (available in certain countries
only)

EN 8

.

2 Use your TV

TV controls

Rear controls

1. Standby indicator LED and remote
control sensor

The standby LED indicates when your TV is
in standby. Point the remote control at the
sensor. Make sure that the line of sight

English

between the remote control and the TV is
not blocked.

Remote control

1

1

2

3

4

1. VOL +/- (Volume): Increase or decrease
volume.

2. CH

: Switch to the next or previous

channel.

3. INPUT: Watch a connected device.
:Switch the TV on or off.

4.

Sensors and indicators

2

3

4
5

1. (Standby): Switch the TV on or to
standby.

2. Play buttons: Control playback of
multimedia files.

SOURCE: Watch a connected device.

3.

4. GUIDE: View program guide.

5. EXIT: Exit from menus or TV functions.

6 8

7

9

6. (Home): Access the Home menu.

7. OK: Confirm an entry or selection.

8. SMART TV: Access Smart TV.
(Navigation buttons): Navigate

9.

through menus and select items.

1

EN 9

1210

1311

10. LIST: Access the TV channel list.
FORMAT: Change the picture format

11.

to suit the video source.

INFO: Display information about

12.

current activity.

OPTIONS: Access currently available

13.

options, picture and sound menus.

14
15

16

17

14.

(Back): Return to the previous menu

page or exit from a TV function.

15. CH +/-: Switch channels.

16. +/- (Volume): Adjust volume.
(Mute): Mute or restore audio.

17.

18

20

19

21

18. Color buttons: Select tasks or options.

The buttons function according to the
services offered by the service provider.

19. SUBTITLE: Switch on or off subtitles.

20. 0-9 (Numeric buttons): Select TV

channels or enter text.

21. TEXT: Enable or disable teletext.

EasyLink controls

If you connect your TV to HDMI-CEC
enabled devices, such as a Blu-ray player or
home theater, you can control them at the
same time with one remote control. Simply
switch on EasyLink after connection.

Read more about Easylink in Connect your

TV > Set up Easylink devices > Control
devices (Page 51).

Onscreen remote control

You can also control connected HDMI-CEC
enabled devices through other buttons that
are available through the onscreen remote
control. Make sure that Easylink is switched
on after connection. Read more about
Easylink in Connect your TV > Set up
Easylink devices > Control devices (Page

51).

To access the onscreen remote control

1. While you watch a connected device,
OPTIONS.

press

2. Select [Show remote control], then press

OK.

3. Select an onscreen button, then press OK.

Smartphone control

With the smartphone application 'Philips
MyRemote', you can use your smartphone

as a secondary remote, and even as a
keyboard. You can also watch a slideshow of
the images in your smartphone on the TV.

Note: Make sure that your TV and
smartphone are connected to the same local
network. For more information, see

Connect your TV > Connect to a network
and the Internet (Page 53).

Follow these instructions to download the
application 'Philips MyRemote':

1. Visit the Apple App store or Google Play

to download the application 'Philips
MyRemote' on your smartphone.

2. Follow the instructions provided at the

applications store.

EN 10

Watch TV

Switch TV on or off

Switch the TV on

 Connect the TV to the mains outlet

and switch on the main power.

 If the TV is not switched on, the

standby LED remains off. Press
the TV.

 If the standby LED is lit, press on the

remote control.

Note: There is a short delay before the TV
responds.

Tip: If you cannot find your remote control
and want to switch on the TV from standby,
press any button the TV.

Switch TV to standby
Press

on the remote control.

The standby LED on the TV switches to red.
Switch off the TV

Press

on the TV.

The standby LED switches to off.
Note: Though your TV consumes very little

energy when it is in standby or switched off,
it does use some energy. If you are not going
to use the TV for an extended period of
time, disconnect the TV from the mains plug.

on

Automatic switch off
You can save energy with this TV's energy
efficiency settings, which are enabled by
default. If there is no user interaction (such
as pressing a remote control button or a

English

control on the TV) for four hours, the TV
will automatically switch to standby.

To disable automatic switch off

1. While you watch TV, press the Green

button on the remote control.

2. Select [Auto switch off], then press OK.

3. Select [Off], then press OK.

Adjust TV volume

Increase or decrease the TV volume

 Press +/- on the remote control.
 Press VOL +/- on the TV.

Mute or restore the TV volume

 Press

on the remote control to

mute the volume.

 Press

again to restore the volume.

Adjust headphone volume

1. Press .

2. Select [Setup] > [TV settings] > [Sound]

> [Headphone volume], then press OK.

3. Select a level.

EN 11

Switch TV channels

 Press CH +/- on the remote control.
 Press CH on the TV.
 Press the Numeric buttons on the

remote control to enter a channel
number.

Manage favorite channels

You can view all channels or only a list of
your favorite channels.

Create a list of your favorite channels

1. Press

LIST.

The channel list is displayed.

2. Select the channel to mark as favorite,
then press

OPTIONS.

3. Select [Add/remove favourites], then
press OK.
The selected channel is marked with an
asterisk.

To remove a channel from the favorites list,
select [Add/remove favourites], and then
press OK.

Display your list of favorite channels

1. Press

LIST, then press OPTIONS.

2. Select [List] > [Favorites] to display
channels in the favorite list.

3. Press OK to confirm.

Manage channel lists

After the channels are installed, you can:

 Filter channels.

 Switch between antenna and cable

channels.

 Rename channels.
 Reorder channels.
 Lock a channel.
 Listen to digital radio.

Filter channels

1. While you watch TV, press

2. Press

3. Select an option, then press OK.

OPTIONS, then select [Filter].

LIST.

 [Digital + Analog]: Display all channels

in the channels list.

 [Digital TV channels]: Display only

digital channels.

 [Analog channels]: Display only analog

channels.

 [Free / scrambled]: Display all channels

in the channels list.

 [Scrambled channels]: Display only

scrambled channels.

 [Free channels]: Display only free

channels.

Note: The filtering options may vary
according to your broadcaster.

Switch between antenna and cable channels
While you watch TV, you can switch
between antenna and cable channels.

1. While you watch TV, press

.

2. Select [Setup] > [Channel settings] >

[Channel installation] > [Antenna
connection].

3. Select [Antenna (DVB-T)] to watch

antenna channels or [Cable (DVB-C)] to
watch cable channels, then press OK.

Rename channels
When you select a channel, its name
appears. You can change this channel name.

1. While you watch TV, press

LIST.

The channel list is displayed.

2. Select the channel to rename, then select

OPTIONS.

3. Select [Rename], then press OK.

The onscreen keyboard is displayed.

4. Press the Navigation buttons to select

each character, then press OK.

5. Once complete, select [Done], then press

OK to confirm.

EN 12

Reorder channels
After the channels are installed, you can
reorder the channel list.

1. While you watch TV, press

LIST.

The channel list is displayed.

2. Press

OPTIONS.

3. Select [Reorder], then press OK.

4. Select the channel to reorder, then press
OK.

5. Press the Navigation buttons to move the
highlighted channel to another location, then

press OK.

6. Once complete, press

7. Select [Exit reorder], then press OK.

OPTIONS.

Lock a channel
You can prevent unauthorized access to
channels by locking them.

1. While you watch TV, press

LIST.

The channel list is displayed.

2. Select the channel to lock, then press
OPTIONS.

3. Select [Lock channel], then press OK.

4. If prompted, enter the pin code.
The channel is marked with a lock icon in
the channel list.

Tip: To watch a locked channel, enter the
pin code when prompted.

Listen to digital radio
If digital radio channels are available, you can
listen to them. They are installed
automatically when you install the TV
channels.

1. While you watch TV, press

LIST.

The channel list is displayed.

2. Press

OPTIONS.

3. Select [Filter] > [Radio], then press OK.

4. Select a radio channel, then press OK.

Watch connected devices

Before you can watch a device, connect the
device to the TV. See Connect your TV >

Connect devices (Page 42).
Select a device with SOURCE

1. Press
control, or INPUT on the TV.

2. Select a device, then press OK.

SOURCE on the remote

Select a device from the Home menu

1. Press

.

2. Select [Source], then press OK.

3. Select the device, then press OK.

To add or manage your connected devices,
see Connect your TV > Watch connected

devices > Change device settings (Page 50).

Use picture and sound presets

Your TV comes with predefined picture and
sound settings. You can apply these settings
or customize them.

Select your preferred picture settings

1. While you watch TV, press OPTIONS.

2. Select [Picture and sound] > [Picture

style], then press OK.

3. Select an option, then press OK:

 [Personal]: Apply your personalized

picture settings.

 [Vivid]: Rich and dynamic settings, ideal

for daytime viewing.

 [Natural]: Natural picture settings.
 [Standard]: Default settings that suit

most environments and types of video.

 [Movie]: Ideal settings for movies.
 [Photo]: Ideal settings for photos.
 [Energy saving]: Settings that conserve

the most energy.

Select your preferred sound settings

1. While you watch TV, press

2. Select [Picture and sound] > [Sound

style], then press OK.

3. Select an option, then press OK:

 [Personal]: Apply your personalized

sound settings.

 [Original]: Settings that suit most

environments and types of audio.

 [Movie]: Ideal settings for movies.
 [Music]: Ideal settings for listening to

music.

 [Game]: Ideal settings for games.
 [News]: Ideal settings for spoken audio,

such as the news.

OPTIONS.

English

EN 13

Change picture format

You can change the picture format to suit
the video source.

1. Press

2. Select a picture format, then press OK.

The available picture formats depend on the
video source:

 [Auto fill]: Adjust the picture to fill the

 [Auto zoom]: Enlarge the picture to fill

 [Super zoom]: Remove the black bars

 [Movie expand 16:9]: Scale 4:3 format

 [Wide screen]: Shows widescreen

 [Unscaled]: Provide maximum detail for

 [4:3]: Display the classic 4:3 format.

FORMAT.

screen (subtitles remain visible).
Recommended for minimal screen
distortion but not for HD or PC.

the screen. Recommended for minimal
screen distortion but not for HD or PC.

on the sides of 4:3 broadcasts. Not
recommended for HD or PC.

to 16:9. Not recommended for HD or
PC.

format content unstretched. Not
recommended for HD or PC.

PC. Only available when PC mode is
selected in the Picture menu.

View program guide

What you can do

NonPublish

You can view channel schedules and
program synopses for digital TV channels
using program guides provided by the
broadcasters. The availability of program
guides is dependent on your broadcaster.

You can view program guides through one
of two methods:

 From the broadcaster
 From the Internet

You cannot view a channel's program guide
information if:

 the age rating of the channel is equal or

higher than the age rating set on your
TV.

 the channel is locked.

From the broadcaster

Select broadcaster program guide

Before you use the program guide, check
these settings:

1. Press

2. Select [Setup] > [TV settings] > [General

settings] > [TV guide].

3. Select [From the broadcaster], then press

OK.
Access broadcaster program guide

1. Press

2. Select [TV guide], then press OK.

3. If you are viewing the program guide for

the first time, follow the onscreen
instructions to update the guide.

Customize broadcaster program guide
You can customize the displayed information
to:

 Remind you when programs start.
 Display only preferred channels.
 Change day of display.
 Schedule recordings of programs. See

.

.

Use more of your TV > Record TV
shows > Schedule recordings (Page

23).

EN 14

Note: Options may vary according to the
program information available from the
broadcaster.

1. In the program guide, press

OPTIONS.

2. Select an option, then press OK:

 [Update TV guide]: Update program

guide information.

 [Change day]: Select the day to display

program guide.

 [Search by genre]: Search programs by

genre.

 [All reminders]: Display a list of all

program reminders.

From the Internet

Make sure that your TV is connected to the
Internet through a high-speed broadband
connection. See Connect your TV >
Connect to a network and the Internet
(Page 53).

Select Internet program guide
Before you use the program guide, check
these settings:

1. Press

2. Select [Setup] > [TV settings] > [General
settings] > [TV guide].

3. Select [From the Internet], then press

OK.
Access Internet program guide

1. Press

2. Select [TV guide], then press OK.

Note: If you are viewing the program guide
for the first time, follow the onscreen
instructions to update the guide.

Customize Internet program guide
You can use the program guide to:

 Schedule recordings of programs. See

 Identify channels.
 Select day of display.
 Reload and zoom into the program

 View security information.

Note: Options may vary according to the
program information available from the
broadcaster.

.

.

Use more of your TV > Record TV
shows > Schedule recordings (Page

23).

guide information.

1. In the program guide, press

2. Select an option, then press OK:

OPTIONS.

 [Record]: Set a scheduled recording.
 [Identify channel]: Manually update

channel information.

 [Select day]: Select the day to display.
 [Manual record]: Set a manual

recording.

 [Reload page]: Refresh the page display.
 [Zoom]: Change zoom level of page

display.

 [Security info]: Display program

security information.

Play multimedia files

What you can do

You can play videos, photos, and music on
your TV from:

 Your computer connected through the

home network.

 A USB device connected to the TV.

Play files from computer

What you need

 A wired or wireless home network,

connected with a Universal Plug and
Play (uPnP) router.

 For wired networks: A LAN cable that

connects your TV to your home
network.

 For wireless networks: A Philips

wireless USB adapter PTA127

 A media server running on your

computer.

 Appropriate settings on your computer

firewall to allow you to run the media
server.

Set up the network

1. Connect your TV and the computer to

the same home network. See Connect your

TV > Connect to a network and the
Internet (Page 53).

2. Switch on your computer and the router.

English

EN 15

Note:
If the apparatus does not return to DLNA
mode due to external electrical disturbances
(e.g. electrostatic discharge), user
intervention is required.

Set up media sharing

1. Install a media server on your computer
to share media files. These are some media
servers:

 For PC: Windows Media Player 11 (or

higher) or TVersity

 For Mac: Twonky

2. Switch on media sharing on your
computer using the media server. For more
information on how to set up the media
server, refer to the website of the media
server.

Play files

1. Press

SOURCE.

2. Select [Browse network], then press OK.

3. Select a file from the content browser,
then press OK to start play.

4. Press the Play buttons to control play.

5. Optional: To select a different media
server, select [Media server].

Tips:

 Select the top bar to filter your files by

type.

 Select [Sort] to arrange the files by

album name, artist, or other fields.

 To clear the list of offline media servers,

OPTIONS, then select [Clear

press

offline servers] and press OK.

Play files from USB device

If you have photos, videos or music files on a
USB storage device, you can play the files on
TV.

Caution:

 TP Vision is not responsible if the USB

storage device is not supported, nor is
it responsible for damage or loss of
data in the device.

 Do not overload the USB port. If you

connect a USB storage device that
consumes more than 500mA power,
make sure that it is connected to its
own external power supply.

Browse USB device

1. Connect the USB device to the USB

connector on the TV.

2. Press SOURCE, select [USB], and

then press OK.

3. Select a file from the content browser,

then press OK to start play.

4. Press the Play buttons to control play.

5. Optional: To select a different USB device,

select [USB device] at the bottom of the TV
screen.

Tips:

 Select the top bar to filter your files by

type.

 Select [Sort] to arrange the files by

name, date, or other fields.

Play options

Watch video

1. Select

2. Select a video, then press OK.

3. Optional: To play all the videos in a folder,

select a video, then select [Play all].

 To skip to the next or previous video,
 To pause the video, press OK.

 To skip forward or backward 10
 To search forward or backward, press

 To stop the video, press

Video options
While you play video, press
then press OK to select an option:

 [Subtitles]: Select the available subtitle
 [Subtitle language]: Select the language
 [Character set]: Select the correct
 [Audio language]: Select an audio

 [Repeat]: Select [Repeat] to play the

in the top bar.

press CH+ or CH -.

Press OK again to resume playback.

seconds, press

or .

or . Press the button repeatedly

to toggle between different speeds.

.

OPTIONS,

settings.

for subtitles if available.

character set for the subtitles.

language.

video file repeatedly or [Play once] to
play the video file once.

EN 16

 [Media server]: When you play content

from a media server, you can select
another media server.

 [Shuffle on] / [Shuffle off]: Enable or

disable random play of video files.

 [DivX(R) VOD]: Display the DivX

registration and deregistration codes for
this TV.

Note:
To view information about a video (for
example, played position, duration, title, or

date), select the video, then press
To hide the information, press
again.

INFO.

INFO

Listen to music

1. Select

in the top bar.

2. Select a track, then press OK.

3. Optional: To play all the tracks in a folder,
select a track, then select [Play all].

 To skip to the next or previous track,

press CH+ or CH-.

 To pause the track, press OK.

Press OK again to resume playback.

 To skip forward or backward 10

seconds, press or .

 To search forward or backward, press

or . Press repeatedly to toggle

between different speeds.

 To stop the music, press .

Music options
While you play music, press OPTIONS,
then press OK to select an option:

 [Repeat]: Select [Repeat] to play a

track or an album repeatedly, or select
[Play once] to play a track once.

 [Media server]: When you play content

from a media server, you can select
another media server.

 [Shuffle on] / [Shuffle off]: Enable or

disable random play of tracks.

Note:
To view information about a song (for
example, title, artist or duration), select the

song, then press
To hide the information, press

INFO.

INFO

again.

View photos

1. Select

in the top bar.

2. Select a photo thumbnail, then press OK.

Start a slideshow
If there are multiple photos in a folder, select

a photo, then select [Slideshow].

 To skip to the next or previous photo,

press CH+ or CH -.

 To stop the slideshow or close the

photo, press

LIST or .

Slideshow options

While you play a slideshow, press
OPTIONS, then press OK to select an

option:

 [Shuffle off] / [Shuffle on]: Enable or

disable random display of pictures in
the slideshow.

 [Repeat]: Select [Repeat] to watch a

slideshow repeatedly or [Play once] to
watch once.

 [Slideshow time]: Select the display

time for each photo in the slideshow.

 [Slideshow transitions]: Select the

transition from one photo to the next.

 [Media server]: When you play content

from a media server, you can select
another media server.

Play DivX® VOD (Video On
Demand)

This TV is DivX Certified(R) and plays high­quality DivX Video-On-Demand videos.

To play DivX VOD videos from a video
store or from your computer, you must first
activate DivX VOD on the TV. The DivX
VOD activation of your TV is free of charge.

Register the TV
If the TV is not yet activated when you start
the playback of a rental DivX video, the TV
displays the DivX registration code to
activate this TV.

To register, follow these steps.

English

EN 17

1. When the TV displays the 8 or 10-digit
registration code, write down the code and
go to http://vod.divx.com.

2. Download the DivX player software on
your computer and install the software.

3. Start the DivX player software and create
a DivX Account: Click VOD > Create a
DivX Account.

4. In the DivX player, register the TV with
the registration code of the TV: Click VOD
> Register a DivX Certified Device.

5. When prompted, download and save the
registration video to a USB flash drive or
your connected media server.

6. Go to your TV and play the registration
video on your TV. This completes the
registration and activates DivX on your TV.

Consult the DivX website for detailed
support.

To de-register this TV:

1. Press

SOURCE.

2. Select [Browse USB], then press OK.

3. Press OPTIONS, select [DivX(R)
VOD], and then press OK.

4. Follow the onscreen instructions.

Smart TV

Note:

 Smart TV services and apps vary from

country to country.

 Availability of catch-up TV apps and

their TV programs is subject to the
country setting of your TV. To find out
which TV programs are available, access
the program guide within the app.

 Smart TV displays one page at a time, in

full screen view.

 Certain websites may not display

completely. Functions that require plug­ins may be unavailable.

 TP Vision Netherlands B.V. bears no

responsibility regarding the content and
the quality of the content provided by
the content service providers.

What you need

1. On your home network, connect the TV

to the Internet.

2. On your TV, configure Smart TV.

3. Optional: On your PC, register with Philips

to enjoy exclusive benefits and receive
updates on product information. You can
register at any time.

What you can do

NonPublish

With Internet Applications (apps), which are
specially adapted Internet websites for your
TV, you can enjoy these features and more:

 Read newspaper headlines
 Watch and rent videos
 Check weather forecasts
 Catch up with TV programs that you

missed

Find out more about Smart TV services from
the Smart TV forum website,

www.supportforum.philips.com.

EN 18

Internet

TV

Router

PC

Connect the TV to the Internet

1. On your home network, connect a router

with a high-speed connection to the
Internet.

2. Switch on the router.

3. Install the network. See Connect the TV

> Connect to a network and the Internet
(Page 53).

Start Smart TV

1. Press SMART TV.

The terms and conditions of use are
displayed.

2. Follow the onscreen instructions to

complete registration.

Note: The first time you start Smart TV, a
prompt asks if you want to enable parental
control to lock adult apps. If you lock an
adult app, advertisements and web pages
that are not adapted for Smart TV remain
accessible.

Access Smart TV apps

You can access apps through the Smart TV
home page. The icons on this page represent
the apps installed on your TV.

To access an app, select the app, then press

OK to confirm.
Add apps

1. Select [App Gallery], then press OK.

2. Select an app, then press OK to add it to
your home screen.

3. Follow the onscreen instructions to add
the app.

Tips:

 You can search for apps available in

other countries.

 To return to the Smart TV home page,

press

LIST.

Note: Smart TV services are updated

automatically. To view the latest updates, in

[App Gallery], select [All], then change to
[New].

Access websites

1. Select an Internet app, then press OK.

2. Select the web address field, then press
OK.

A keyboard appears on the screen.

3. For each character of the web address,
select the character, then press OK.

Tip: You can also use the Numeric buttons
on the TV remote control to enter a web
address.

Zoom page
To zoom in and out on an Internet page, do
the following:

1. Press

2. Use the slider bar to set the enlargement.

3. Use the Navigation buttons to jump
between highlighted items and scroll through
an Internet page.

OPTIONS, then select [Zoom].

Scroll pages
Press the Navigation buttons

and to

scroll up and down on a web page.
Reload page

If a page does not load correctly, press

OPTIONS, then select [Reload page].
View security info

To view security information about a page,
press OPTIONS, then select [Security

info].

Smart TV options

Clear Smart TV memory

You can clear the Smart TV memory
completely, including your favorites, parental
control code, passwords, cookies, and
history.

Warning: This option resets the Smart TV
memory completely. It also deletes the
settings of other interactive applications such
as DTVi (Digital TV interactive).

1. Press

.

2. Select [Setup] > [Network settings].

3. Select [Clear Internet memory], then

press OK.

Rent online videos

What you need

Make sure that your TV is connected to the
Internet through a high-speed broadband
connection. See Connect your TV >
Connect to a network and the Internet
(Page 53).

Format the USB flash drive
Before you download rented videos, your
USB drive must be formatted. All existing
content on the USB drive is erased.

1. Switch on the TV.

2. Connect the USB flash drive to a USB slot

on the TV.

3. Press

4. After formatting, leave the USB drive

connected to the TV.

to start formatting the drive.

English

EN 19

Access a video store

1. Press SMART TV.

2. Access the [App Gallery] to search for
available video store apps in your country.

3. Select a store, then press OK to confirm.
The icon of the video store is added to the
home page.

4. To access a store, select its icon and press

OK.

Rent a video

Follow the onscreen instructions to rent and
watch the video.

1. Open a video store app. You may need to
register or enter your log-in information.

2. Select a video.

3. Make the online payment.

4. Start watching the video.

Interactive TV

What you can do

With interactive TV, you can view additional
information or entertainment pages provided
by digital TV broadcasters. You can
experience true interactivity by responding
directly to the digital content.

Note: You cannot download files to your TV
with this feature.

Broadcasters use various interactive TV
systems such as:

 HbbTV (Hybrid Broadcast Broadband

TV)

 iTV (Interactive TV - MHEG)
 MHP (Multimedia Home Platform)
 DTVi (Digital TV interactive)

Visit the broadcaster's website for more
information to see which interactive system
is available in your country.

Here are some examples of interactive
activities you can enjoy:

 View information about TV programs
 Join a quiz or contest
 Play games
 Shop online

 Pay for a video-on-demand (VOD)

program

 Vote
 Chat

What you need

To enjoy this service, you need:

 Digital channels with interactive services
 A wired or wireless home network,

connected through a Universal Plug and
Play router (uPnP).

For network connection, see Connect your

TV > Connect to a network and the
Internet (Page 53).

Access interactive TV

You can identify channels that offer
interactive services by a message that invites
you to press the Red button or OK to
access an interactive program.

1. Switch to a digital channel with interactive

services.
When the application is loading, a blinking
symbol is displayed. When the application
has loaded, an icon is displayed.

2. Press the Red button or OK to launch

the interactive application.

3. Follow the onscreen instructions and use

your remote control to navigate the
interactive pages.

EN 20

3 Use more of

your TV

Pause TV

What you can do

While you watch a digital channel, you can
pause a program to answer a phone call or
to have a break. The broadcast is stored on
a USB hard drive that is connected to the
TV. You can resume playback of the
program at any time.

Note:

 You can pause a program for a

maximum of 90 minutes.

What you need

 Tune your TV to receive digital

channels. See Change your TV settings
> Channels > Automatic installation
(Page 34).

 Connect a USB 2.0 compatible hard

drive with a minimum capacity of 4 GB
and a minimum transfer speed of 30
megabits per second. For optimal
performance, use a hard drive with 32
GB disk space.

Install USB hard drive

To pause TV, you must connect a USB hard
drive to the TV and format it.

If the TV does not recognize the USB hard
drive, use a PC to format it to NTFS or
FAT32 system, and then try again.

Caution:

 TP Vision is not responsible if the USB

hard drive is not supported, nor is it
responsible for damage or loss of data
in the device.

 Formatting removes all data from the

connected USB hard drive.

 The USB hard drive is formatted

exclusively for this TV. Keep it
permanently connected to the TV. You
cannot access the contents of the USB
hard drive from another TV or PC.

 Do not overload the USB port. If you

connect a USB hard drive device that
consumes more than 500mA power,
make sure that it is connected to its
own external power supply.

Note:

 Make sure that the TV and the USB

hard drive are switched off.

 While you are formatting the USB hard

drive, do not connect other USB
devices to the TV.

USB

1. Connect the USB hard drive directly to

the TV, or if you intend to connect other
USB devices in future, connect the USB hard
drive through a USB hub.
Make sure that the USB hub is connected to
the USB 1 port on the TV.

2. Switch on the TV and the USB hard drive,

if it has an external power source.

3. Switch to a digital TV channel.

4. Press to start formatting the USB hard

drive.

5. Follow the onscreen instructions to

complete the formatting process.
Warning: The formatting process may take

some time. Do not switch off the TV or
disconnect the USB hard drive until this
process is complete.

English

EN 21

Pause a live TV broadcast

07:24 08:31

07:55:06

ACB

1. On a digital channel, press

to pause a

TV program.

2. Press

to continue watching.

The status bar shows these time indicators:
A. When the program was paused for the

first time.
B. Where the paused program is currently

playing.
C. Where the live program is currently

broadcast.

 To watch the stored broadcast, press

or to search backward or

forward.

 To change playback speed, press

or

repeatedly.

 To watch the live TV broadcast, press

.

Note: If a recording is in progress, you
cannot pause the TV broadcast.

The stored broadcast on the USB hard
drive is deleted if you:

 Disconnect the USB hard drive.
 Start recording a TV program.
 Access Smart TV.
 Switch the TV to standby.
 Switch to another channel.
 Switch source to watch from a

connected device, such as a Blu-ray disc
player or digital receiver.

Record TV shows

What you can do

If your TV can receive program guides, you
can record TV programs onto a USB hard
drive. You can record both current TV
programs as well as future TV programs.

Note:

 Recording is only supported in

countries with program guides.

 In Nordic countries, the TV provides

limited support for subtitles while
recording TV programs.

What you need

 Tune your TV to receive digital TV

channels such as DVB broadcasts. See

Change your TV settings > Channels >
Automatic installation (Page 34).

 Connect a USB 2.0 compatible hard

drive with a minimum capacity of 32
GB and a minimum transfer speed of
30 megabits per second. For optimal
performance, use a hard drive with 250
GB disk space. You can use the same
USB hard drive to record and pause TV
shows.

Install USB hard drive

To record TV shows, you must connect a
USB hard drive to the TV and format it.

If the TV does not recognize the USB hard
drive, use a PC to format it to NTFS or
FAT32 system, and then try again.

Caution:

 TP Vision is not responsible if the USB

hard drive is not supported, nor is it
responsible for damage or loss of data
in the device.

 Formatting removes all data from the

connected USB hard drive.

 The USB hard drive is formatted

exclusively for this TV. Keep it
permanently connected to the TV. You
cannot access the contents of the USB
hard drive from another TV or PC.

EN 22

 Do not overload the USB port. If you

connect a USB hard drive device that
consumes more than 500mA power,
make sure that it is connected to its
own external power supply.

Note:

 Make sure that the TV and the USB

hard drive are switched off.

 While you are formatting the USB hard

drive, do not connect other USB
devices to the TV.

USB

1. Connect the USB hard drive directly to
the TV, or if you intend to connect other
USB devices in future, connect the USB hard
drive through a USB hub.

2. Switch on the TV and the USB hard drive,
if it has an external power source.

3. Switch to a digital TV channel.

4. Press to start formatting the USB hard
drive.

5. Follow the onscreen instructions to
complete the formatting process.

Warning: The formatting process may take
some time. Do not switch off the TV or
disconnect the USB hard drive until this
process is complete.

Start recording

English

One-touch recording

You can record the program you are
currently watching with a single button.

1. While you watch TV, press .

Recording starts immediately. A pop-up
window is displayed, indicating the end time
of the program.

2. Optional: Use the Navigation buttons to

mark the end time of the recording.

3. Select [Confirm], then press OK.

4. To stop recording, press .

Note:

 While recording, you cannot switch TV

channels or pause a TV broadcast.

 If TV guide information is not available,

a default time of 30 minutes is set for
recording. You can change this if
needed.

Schedule recordings

View program information

Depending on the status of a program, you
can start watching it or schedule to record
the program.

1. Press

2. Select [TV guide].

3. Select a channel and program, then press

OK.
The program information is displayed.

Note: If you schedule recordings while you
are away, make sure that you leave the TV in
standby and keep the USB hard drive
switched on.

.

EN 23

Schedule a TV program recording
You can schedule a recording of an
upcoming program that will be broadcast
today or up to eight days later. You can also
schedule a timed recording that is not linked
to any program, if program guide information
is not available.

1. Press

, then select [TV guide].

2. Select the channel and program to record.

3. Optional: To record a program that will
be broadcast on another day: press
OPTIONS, select [Change day], then select
another day.

4. Select [Record].
A pop-up window is displayed.

5. Select and change the recording details
with the Numeric buttons and Navigation
buttons.

6. Select [Confirm], then press OK.
Change a scheduled recording

1. Press

.

2. Select [Recordings], then press OK.
A list of scheduled recordings is displayed.

3. Select the recording, then select [Adjust
time].

4. Change the recording time as needed,
then select [Confirm].

Cancel a scheduled recording

1. Press

.

2. Select [Recordings], then press OK.
A list of recordings is displayed.

3. Select the recording, then select
[Remove].

The schedule recording is canceled.

Watch recordings

1. Press .

2. Select [Recordings], then press OK.

A list of recordings is displayed.

3. Select a recording from the list, then press

OK.
The recording starts to play.

Sort recordings

1. Press

.

2. Select [Recordings], then press OK.

A list of recordings is displayed.

3. Press

OPTIONS.

4. Select an option to sort by name, date,

expiry date or type, then press OK.

Note:

 If a broadcaster limits the number of

days a recording can be viewed after
the program is broadcast, the list of
recordings shows the number of days
before the recording expires.

 If a recording has expired or if a

broadcaster restricts playback, the
recording cannot be played.

 If a scheduled recording is prevented by

the broadcaster or if the recording does
not occur as per schedule, it is marked
as [Failed] in the recordings list.

Delete recordings

The [Recordings] page shows a list of all
recordings and the remaining USB hard disk
space. You can delete recordings to free up
disk space.

1. Press

2. Select [TV guide] > [Recordings], then

press OK.
A list of recordings is displayed.

3. Select the recording, then select

[Remove].

.

EN 24

Use Skype™

What you can do

 Talk to anyone else on Skype,

anywhere in the world, for free.

 Make low-cost calls to phones and

mobiles. A Skype subscription is
required. Visit www.skype.com.

 Participate in conference calls.
 Send and receive voicemails.
 Forward a call.
 Manage your online status, 'mood'

message, and profile information.

Note:

 No emergency calls with Skype. Skype

is not a replacement for your telephone
and cannot be used for emergency calls.

 This TV comes with Skype pre-installed

on it and ready to use. You do not
need to install or download any files for
using Skype. Simply connect a Philips
TV video camera to use Skype.

What you need

 A Philips TV video camera, PTA317/00

(sold separately), with built-in
microphone. See Connect your TV >

Connect more devices > Video call
camera (Page 49).

 An Internet connection.
 A wired or wireless home network. For

network connection, see Connect your
TV > Connect to a network and the
Internet (Page 53).

 A Skype account. You can create a

Skype account on this TV or from your
computer.

Tip: If you have connected a USB keyboard
to this TV, you can enter text from your
keyboard. For keyboard connections, see

Connect your TV > Connect more devices
> Keyboard and mouse.

English

Start Skype

Sign in to your account

1. Press

2. Enter your [Skype name] and [Password].

To enter text, select each field and press OK
to access the onscreen keyboard.

3. Select [Sign in], then press OK.

The Skype menu is displayed.
Tip: If you have forgotten your password,

start Skype on your computer. Visit

www.skype.com to retrieve your password.

Create an account

If you do not have a Skype name and
password, you can create an account from
your TV.

1. Select [Don't have a Skype Name?], then

press OK.

2. Read the Skype End User License

Agreement, Terms of Service and Privacy
Statement. Once complete, select [Accept]
and press OK.

3. When prompted, add information about

your name, Skype name, password and email
address.

4. Once complete, select [Create an

account] and press OK.
Your new account is accepted and you are
signed in.
If prompted, follow the onscreen instructions
to make changes to the entries.

Sign out from Skype
In the Skype menu, select [Sign Out], then
press OK.

, then select [Skype].

EN 25

Manage contacts

You can add and view contacts that are
online or offline. You can also block or
unblock a selected contact.

Add a contact

1. In the Skype menu, select [Contacts],
then press OK.

2. Press

Skype contact] or [Add SkypeOut
Contact].

3. Press OK to display the onscreen
keyboard.

4. Follow the onscreen instructions to enter
the details.
A list of profiles is displayed.

5. Select a contact, then press OK.
An invitation request is sent to the contact.
The contact name appears offline until the
contact accepts the request.

Accept a contact request
Other Skype users can invite you to be on
their contact list. You will be notified of their
request, which you can accept or decline.

Rename a contact

1. In the Skype menu, select [Contacts],
then press OK.

2. Select a contact, then press OPTIONS.

3. Select [Rename], then press OK.

4. Follow the onscreen instructions to edit
the information.

Block a contact

1. In the Skype menu, select [Contacts],
then press OK.

2. Select the contact, then press
OPTIONS.

3. Select [Block], then press OK. When
prompted, select [Yes] then press OK.

Unblock a contact

1. In the Skype menu, select [Settings] >
[Blocked Contacts].

2. Select the blocked contact, then press
OK.

3. Follow the onscreen instructions to
unblock the contact.

OPTIONS, then select [Add

Contact info
To view the details of a contact, select a
contact. The contact details are displayed on
the right of the TV screen.

Contact history
To view the calls which you have had with a

contact, select [History].

To open previous conversations, select a
conversation and press OK.

Note: When you sign in with another Skype
account on this TV, the history of your
previous account is cleared.

Online status
To see if a contact is online, check the online
status icon next to the contact. Your online
status is also shown on your contacts' page.

To change your online status:

1. In the Skype menu, select your Skype

name, then press OK.

2. Select [Online Status], then press OK.

3. Select a status, then press OK.

Make voice and video calls

Make a voice call

You can make a Skype call without video.
Note: Make sure that a video camera is

connected for voice calls also.

1. In the Skype main menu, select

[Contacts], then press OK.

2. Select the contact, then press OK.

3. Select [Call], then press OK.

Voice call options
During a call, press
these options:

 [Mute]: Mute the microphone.
 [Hold]: Put the call on hold.
 [End call]: End the call.
 [Dial pad]: Access the dial pad.
 [Start My Video]: Start video camera.

Make a video call
With video calls, you can talk face-to-face
with live video from your TV for free.

1. From the Skype menu, select [Contacts],

then press OK.

2. Select the contact, then press OK.

3. Select [Video call], then press OK.

OPTIONS to access

EN 26

Full screen view
If your contact has a camera connected and
accepts the call, you can see the person on
your TV, in full screen. To check what your
contact can see, view the display in the small
screen on your TV.

1. During the call, press

2. Select [Full view], then press OK.

OPTIONS.

Zoom and pan your video

1. In [Full view], select [Zoom] +/- to zoom
in or zoom out.
A zoom and pan icon appears above the
video display.

2. Use the Navigation buttons on the
remote control to pan or tilt the camera.

Video call options
During a video call, press

OPTIONS to

access these options:

 [Full view]: See your contact in full

screen view.

 [Dial pad]: Access dial pad.
 [Hold]: Put the call on hold. Full view

will be stopped.

 [Mute]: Mute the microphone.
 [Stop My Video]: Stop the video feed

to your contact's screen.

Call a phone
With Skype, you can call land line phones
and mobile phones.

Note:
No emergency calls with Skype. Skype is not
a replacement for your telephone and
cannot be used for emergency calls.

1. In the Skype menu, select [Call phones],

and then press OK.

2. Select [Dial pad] to access the onscreen

dial pad or enter the telephone number with
the Numeric buttons.

3. Once complete, select [Call], and then

press OK to start the call.

4. Optional: To mute your microphone

during your call, press

OPTIONS, and

then select [Mute].

5. To end the voice call, select [End call],

and then press OK.

Answer a call
If you are signed in to Skype, you are notified
of incoming calls while watching TV.

1. A message appears onscreen with the

caller's name. Select [Answer], then press
OK.
To enable video, select [Answer with
video], then press OK.

2. To decline, select [Decline], and then

press OK.
Note:

If you accept a call while pausing or
recording a TV program is paused, or while
watching rental movies, Skype will interrupt
the on-going activity.

 A paused TV program is stopped and

the program storage is lost.

 Recording of a TV program is stopped.

You will need to resume recording
again after you finish the call.

 Playback of rental movies is stopped.

To resume watching the rented movie,
you need to go back to the video store
or broadcast service. Some video stores
and services do not allow you to restart
the movie.

English

Before you can make a call, you will need to
purchase Skype Credits or buy a Skype
subscription on your computer. For more
information, see Use more of your TV >
Use Skype > Skype settings. (Page 28)

EN 27

Manage voicemails

If someone calls you on Skype and you are
offline, they can leave a voice message in
your Skype voicemail.

Before you can receive voicemail, you need
to activate voicemail in your Skype account
— this can only be done on your computer.

Play voicemail

1. In the Skype menu, select [History] and
press OK.

2. Select [Voicemails], then press OK.

3. Select the voicemail, then press OK to
play it.

Delete voicemails

1. Select the voicemail from the list and
press

OPTIONS.

2. Select [Delete voicemail], then press OK.

Skype settings

Skype Credit

With Skype Credit, you can call land lines or
mobile phones on your TV. To purchase
Skype Credit, you need to log in to your
Skype account on your computer. The
amount of Skype Credit you purchase will
appear when you log in to your Skype
account on your TV.

Automatic sign in

1. In the Skype menu, select [Settings], and
then press OK.

2. Select [General settings] > [Sign me in

when Skype starts], then press OK.

Change your profile picture

1. In the Skype menu, select your Skype
name, then press OK.

2. Select [Profile picture], then press

3. Choose a picture, select [Apply], and then
press OK.

Change your Skype password

1. In the Skype menu, select [Settings], then
press OK.

2. Select [Change Password], then press

3. Follow the onscreen instructions to enter
your current and new passwords.

4. Once complete, select [Apply] and then
press OK.

.

.

Play games

What you can do

On this TV, you can play regular games in
full-screen with optimized picture settings for
games.

What you need

 Connect your game console to this TV.

See Connect your TV > Connect
devices > Game console (Page 45).
If the TV automatically adds the game
console to the Source menu, it also
applies the game sound preset when
you start playing games (for certain
models).

Start gaming

1. Press SOURCE.

2. Select the game console, then press OK.

3. If needed, load a game disc on the game

console, then select a game to play.

4. Follow the onscreen instructions to start

gaming.

Game settings

Picture setting for games

You can optimize the TV display for gaming
without picture lag.

1. Press

2. Select [Setup] > [TV settings] >

[Picture], then press OK.

3. Select [Game or computer] > [Game].

Sound preset for games
You can optimize sound effects for gaming.

1. Press

2. Select [Picture and sound] > [Sound

style] > [Game], then press OK.
The TV is ready for gaming.

Note: When your gaming session ends,
switch back to your usual sound setting.

.

OPTIONS.

EN 28

View Teletext

Select a page

While you watch channels that broadcast
teletext, you can view the teletext.

1. Select a channel that broadcasts teletext,
then press TEXT.

2. Select a page in one of these ways:

 Enter the page number with the

Numeric buttons.

 Press CH + / CH - to view the next or

previous page.

 Press the Color buttons to select a

color coded item.

Teletext options

1. While you view teletext, press
OPTIONS.

2. Select an option:

 [Freeze page] / [Unfreeze page]:

Freeze or unfreeze the current page.

 [Dual screen] / [Full screen]: Enable or

disable dual screen teletext. Dual
screen displays both the current
channel and the teletext broadcast on
two halves of the TV screen.

 [T.O.P. overview]: Table Of Pages

(T.O.P.) teletext broadcasts allow you
to jump from one subject to another
without entering page numbers.

 [Enlarge] / [Normal view]: Zoom in on

the page. Press the Navigation buttons
to move around the enlarged view.

 [Reveal]: Hide or reveal hidden

information on a page, such as solutions
to riddles or puzzles.

 [Cycle subpages]: If subpages are

available, each is shown automatically.

 [Language]: Switch to a different

language group to correctly display
different character sets.

 [Text 2.5]: View teletext with more

colors and better graphics than normal
teletext. If Teletext 2.5 is broadcast by
a channel, it is switched on by default.

Teletext language

For digital TV channels where the
broadcasters provide different teletext
languages, you can select your preferred
primary and secondary language.

1. Press .

2. Select [Setup] > [Channel settings].

3. Select [Languages] > [Primary Text] or

[Secondary Text].

4. Select a language, then press OK.

Subpages

If the teletext page contains several
subpages, you can view each subpage in
succession. These subpages are shown on a
bar next to the main page number.

Press

or to select them.

Search

You can search for a word or number that
exists on the current teletext page.

1. While you view teletext, press OK to

highlight the first word or number.

2. Press the Navigation buttons to skip to

the word or number to search.

3. Press OK to begin the search.

4. To exit the search, press

or number is highlighted.

until no word

English

EN 29

Set locks and timers

Clock

You can display a clock on the TV. The clock
displays the time that is broadcast by your
TV service operator.

Display the TV clock

1. While you watch TV, press

2. Select [Clock], then press OK.
The clock is displayed on the top right-hand
corner of the TV screen.

Change the clock mode
You can change the clock mode to
automatic or manual. By default, it is set to
automatic mode, which automatically
synchronizes it to Coordinated Universal
Time (UTC). If your TV cannot receive UTC
transmissions, change the clock mode to

[Manual].

1. While you watch TV, press .

2. Select [Setup] > [TV settings] > [General
settings].

3. Select [Clock] > [Auto clock mode].

4. Select [Automatic], [Manual] or [Country

dependent], then press OK.

Change the time zone

In countries with clock transmission data, you
can change the time zone if [Auto clock

mode] > [Automatic] or [Country
dependent] is selected.

1. In the [Clock] menu, select [Time zone].

2. Select your time zone, then press OK.

Set daylight saving time
In countries with clock transmission data, you
can enable or disable daylight saving time if

[Auto clock mode] > [Automatic] or
[Country dependent] is selected.

1. In the [Clock] menu, select [Daylight
saving].

2. Select [Standard time] or [Daylight saving
time], then press OK.

OPTIONS.

Set the clock manually

You can set the date and time manually.
Before you start, set the clock mode to
[Manual].

1. In the [Clock] menu, select [Date] or

[Time], then press OK.

2. Set the time or date with the Navigation

buttons.

3. Select [Done], then press OK.

Sleep timer

You can switch the TV to standby after a
specified time. During the countdown to the
specified time, you can switch off your TV
earlier or reset the sleep timer.

1. Press

2. Select [Setup] > [TV settings] > [General

settings] > [Sleep timer].

3. Select the sleep timer duration.

The sleep timer can be set up for to 180
minutes. To switch off the sleep timer, set it
to zero minutes.

4. Press OK to activate the sleep timer.

After the specified time, the TV switches to
standby.

.

EN 30

Child lock

To protect children from unsuitable TV
programs, you can lock the TV or block age
rated programs.

Set or change the child lock code

1. Press

2. Select [Setup] > [Channel settings] >
[Child lock].

3. Select [Set code] or [Change code].

4. Enter the code with the Numeric

buttons.

Tip: If you access the channels from the

channel list, you are prompted to enter your
lock code. If you forget your code, enter
‘8888’ to override any existing codes.

Lock or unlock channels

1. In the child lock menu, select [Channel
lock].

2. Enter the child lock code with the
Numeric buttons.

3. Select the channels to lock or unlock.
Restart the TV to activate the lock.

Note:
If you access the channels from the channel
list, you are prompted to enter your lock
code.

.

English

Parental rating

You can set your TV to display only
programs with age ratings lower than your
child’s age. This restriction only applies to
digital channels from broadcasters that rate
their programs according to age.

1. Press .

2. Select [Setup] > [Channel settings].

3. Select [Child lock] > [Parental rating].
You are prompted to enter the child lock
code.

4. Enter the child lock code with the
Numeric buttons.

5. Select an age rating, then press OK.
All programs above the selected age rating
are blocked.

For information on child lock codes, see Use

more of your TV > Set locks and timers >
Child lock (Page 30).

EN 31

4 Change your TV

settings

Picture and sound

Settings assistant

You can select picture and sound settings
with the help of the settings assistant, which
demonstrates the effect of your chosen
setting immediately.

1. While you watch TV, press .

2. Select [Setup] > [Quick picture and
sound settings], then press OK.

3. Select [Continue], then press OK.

4. Follow the onscreen instructions to
choose your preferred settings.

More picture settings

You can change the settings in the Picture
menu.

1. Press

2. Select [Setup] > [TV settings] >
[Picture], then press OK.

3. Select a setting to change, then press OK.

 [Picture style]: Select a predefined
 [Restore style]: Restores the
 [Backlight contrast ]: Adjust the
 [Color]: Adjust the color saturation of
 [Sharpness]: Adjust the sharpness of
 [Noise reduction]: Select the amount
 [MPEG artifact reduction]: Smoothen

.

picture setting.

previously-selected picture settings.

brightness of the display backlight.

the picture.

the picture.

of noise reduction for the picture.

transitions and haziness in the digital
picture.

 - [Digital Crystal Clear]: Fine-tune

each pixel to match surrounding pixels
and produce a brilliant, high-definition
image.

- [Advanced sharpness]: Enable
superior sharpness, especially on lines
and contours in the picture

- [Dynamic contrast]: Dynamically

enhance the details in the dark, medium, and
light areas of the picture.

- [Dynamic backlight]: Select a

backlight level to optimize dynamic power
consumption and picture contrast.

- [Color enhancement]:

Dynamically enhance the vividness and
details of colors.

 [Advanced]: Access advanced settings

such as gamma, tint settings and video
contrast settings.

- [Gamma]: Adjust the non-linear
setting for picture luminance and
contrast.

- [Tint]: Change the color balance.

- [Custom tint]: Customize color

balance setting. Only available if [Tint] >
[Custom] is selected.

- [Video contrast]: Adjust video

contrast.

- [Brightness]: Adjust screen brightness.

- [Hue]: Compensate color variations in

NTSC transmissions.

 [Game or computer]: When viewing

content from a connected game
console, select [Game] to apply game

settings. When a computer is
connected through HDMI, select

[Computer]. Make sure that [Format
and edges] > [Picture format] >
[Unscaled] is selected to view

maximum detail.

 [Format and edges]: Access advanced

settings to control the display format of
the picture.

- [Picture format]: Change the
picture format.

- [Screen edges]: Change the
picture size.

- [Picture shift]: If available, move
the position of the picture.

EN 32

More sound settings

You can change the settings in the Sound
menu.

1. Press

2. Select [Setup] > [TV settings] > [Sound],
then press OK.

3. Select a setting to change, then press OK.

 [Sound style]: Access predefined sound
 [Restore style]: Restore the last-
 [Bass]: Adjust the bass level of the
 [Treble]: Adjust the treble level of the
 [Surround mode]: Select a surround

 [Auto incredible surround 3D]: Select

 [Headphone volume]: Adjust

 [Advanced]: Access advanced settings

- [Clear sound]: Enhance sound
quality.

- [Audio Out format]: Select the
type of audio output through the digital
audio output connector. Choose between

[Multichannel] and [Stereo].

.

settings.

selected predefined sound setting.

speaker and headphones.

speaker and headphones.

sound mode to enhance your audio
experience.

a surround sound mode to enhance
your audio experience in 3D mode. For
certain models.

headphone volume.

to enhance your audio experience.

- [Auto volume leveling]: Enable
the reduction of sudden volume
changes, for example, when switching
channels.

- [TV speakers]: Select the
preferred speakers to stream audio

from the TV. See Connect your TV >

Set up EasyLink devices > Select
speaker output (Page 51).

- [Audio Out levelling]: Set the

output level for stereo audio. Select [Less]
for a certain amount of loss in intensity or

signal strength. Select [More] for no loss in
intensity or signal strength.

- [HDMI 1 - ARC]: Enable audio

output from the ARC-compliant device
connected to the HDMI 1 connector.

- [Audio out delay]: Automatically

sync the image on the TV to the audio from
a connected home theater. You do not need
to use this setting when connecting the TV
to a Philips home theater.

- [Audio out offset]: Adjust the

setting for audio output delay. Available if

[Audio out delay] is switched on.

Audio format

Digital channels

If a digital TV channel broadcaster streams
audio in multiple formats, you can select an
audio format.

1. Press

2. Select [Setup] > [Channel settings] >

[Languages] > [Preferred audio format].

3. Select an option, then press OK.

 [Standard]: Receive standard audio
 [Advanced]: Receive advanced audio

If an analog TV channel broadcaster streams
stereo audio in multiple formats, you can
select an audio format.

1. Press .

2. Select [Setup] > [Channel settings] >

[Mono/Stereo].

3. Select a setting, then press OK.

.

format (MPEG).

formats, if available (AAC, Dolby
Digital, or Dolby Digital Plus).

English

EN 33

Reset picture and sound

You can restore the default picture and
sound settings, while the channel installation
settings remain the same.

1. While you watch TV, press

.

2. Select [Setup] > [TV settings] > [General

settings] > [Factory settings], then press
OK.

3. Select [OK], then press OK.

All TV settings (except for channel settings)
are reset to the default factory settings.

Channels

Automatic installation

When the TV was switched on for the first
time, a full installation of channels was
performed.

To change your language, country, and
reinstall all available TV channels, you can run
this full installation again.

Start installation
Note: If you are prompted to enter a code,

enter '8888'.

1. Press .

2. Select [Setup] > [Search for channels] >
[Reinstall channels], then press OK.

3. Select your country, then press OK.

4. Select your network, then press OK:

 [Antenna (DVB-T)]: Access free-to-air

antenna transmissions.

 [Cable (DVB-C)]: Access cable

transmissions.

5. Follow the onscreen instructions to select
other options, if any.
The start menu for channel search is
displayed.

6. Select [Start], then press OK.

7. Once the channel search is complete,
select [Finish], then press OK.

Tip: Press

Note: When digital TV channels are found,

the list of installed channels may display
empty channel numbers. You can rename or
reorder these channels.

LIST to see the channel list.

Install analog channels

You can search and store analog TV
channels one by one.

Step 1: Select your system
Note: Skip this step if your system settings

are correct.

1. While you watch TV, press .

2. Select [Setup] > [Channel settings] >

[Channel installation].

3. Select [Analogue: Manual installation] >

[System], then press OK.

4. Select the system for your country or

region, then press OK.

Step 2: Search and store new TV channels

1. While you watch TV, press

2. Select [Setup] > [Channel settings] >

[Channel installation].

3. Select [Analogue: Manual installation] >

[Search channel], then press OK.

4. Find the channel:

 If you know the channel frequency,

enter it with the Navigation buttons or
Numeric buttons.

 If you do not know the channel

frequency, search for the next
frequency that has a strong signal.
Select [Search], then press OK.

5. After you find the correct channel, select

[Done], then press OK.

6. Select [Store as new channel], then press

OK to store the new TV channel.

Note: If the reception is poor, reposition

your antenna and repeat the procedure.

.

EN 34

Install digital channels

If you know the channel frequency of the
channels you want to install, you can search
and store digital channels one by one. For
best results, contact the service provider.

1. Press

.

2. Select [Setup] > [Channel settings] >
[Channel installation].

3. Select [Digital: Reception test] > [Search
channel], then press OK.

4. Press the Numeric buttons to enter the
channel frequency.

5. Select [Search], then press OK.

6. When the channel is found, select [Store],
then press OK.

Fine-tune analog channels

If the reception of an analog TV channel is
poor, you can fine-tune the TV channel.

1. Press .

2. Select [Setup] > [Channel settings] >
[Channel installation].

3. Select [Analogue: Manual installation] >
[Fine tune], then press OK.

4. Press

or to fine-tune the channel.

5. When you have selected the correct
channel frequency, select [Done], then press
OK.

6. Select an option, then press OK.

 [Store current channel]: Store the

channel under the current channel
number.

 [Store as new channel]: Store the

channel under a new channel number.

Update channel list

When the TV was switched on for the first
time, a full installation of channels was
performed. By default, when there are
changes to these channel lists, the TV
updates them automatically. You can also
switch off the automatic update, or manually
update the channels.

Note: If you are prompted to enter a code,
enter '8888'.

Automatic update
To add or remove digital channels
automatically, leave the TV in standby mode.
The TV updates channels and stores new
channels everyday. Empty channels are
removed from the channel list.

Switch off the channel update message
If a channel update is performed, a message
is displayed at startup. You can switch off this
message.

1. Press

.

2. Select [Setup] > [Channel settings].

3. Select [Channel installation] > [Channel

update message].

4. Select [Off], then press OK.

Switch off automatic updates
In the [Channel installation] menu, select

[Automatic channel update] > [Off].

Update channels manually

1. Press

.

2. Select [Setup] > [Search for channels] >

[Update channels], then press OK.

3. Follow the onscreen instructions to

update the channels.

Copy channels

ATTENTION: This feature is intended for

dealers and service personnel.
You can copy channel lists from one Philips

TV to another through a USB storage
device. You do not need to search for
channels or install them again on the second
TV. The channel list file is small enough to fit
on any USB storage device.

What you need
Two Philips TVs that have these properties:

 The same country setting
 The same year range
 The same DVB type, as indicated by

the suffix (H, K, T, D/00) in the model
name

 The same hardware type, as indicated

by the sticker on the back of the TV.
For example: TPM10.1E LA.

 Compatible software versions

Note: If you are prompted to enter a code,
enter '8888'.

English

EN 35

Step 1: Check the country setting

1. Switch on the first TV (with the channels
that you want to copy to the second TV).

2. Press

.

3. Select [Setup] > [Search for channels] >
[Reinstall channels], then press OK.
The country menu is displayed.

4. Make a note of the current setting.

5. Press

6. Press [Cancel] to exit.

.

Step 2: Copy channel list to USB

1. Connect a USB storage device to the first
TV (with the channels installed on it).

2. Press .

3. Select [Setup] > [Channel settings].

4. Select [Channel installation] > [Copy

channel list] > [Copy to USB], then press
OK.

The channel list is copied to the USB storage
device.

5. Disconnect the USB storage device.

Step 3: Copy channels to a TV with no
channels installed

1. Switch on the second TV, on which you
want to copy the channel list.
Initial installation starts.

2. Follow the onscreen instructions and
select the same country as the TV whose
channel list you want to copy.

3. Skip the search for channels.

4. Connect the USB storage device.

5. Press .

6. Select [Setup] > [Channel settings].

7. Select [Channel installation] > [Copy

channel list] > [Copy to TV], then press
OK.

The channel list is copied to the TV.

8. Disconnect the USB storage device.

Step 3: Copy channels to a TV with pre­installed channels

1. Switch on the second TV, on which you
want to copy the channel list.

2. Press .

3. Select [Setup] > [Search for channels] >
[Reinstall channels], then press OK.
The country menu is displayed.

4. Make sure that the country setting is the

same as the first TV.

5. Press

6. Press [Cancel] to exit.

.

7. If the country setting is different, reinstall

the second TV to match the country setting
of the first TV. See Change your TV settings
> Reset all (Page 40).

8. Connect the USB storage device to the

second TV.

9. Press

.

10. Select [Setup] > [Channel settings].

11. Select [Channel installation] > [Copy

channel list] > [Copy to TV], then press
OK.

The channel list is copied to the second TV.

12. Disconnect the USB storage device.

Language settings

Menu language

1. While you watch TV, press .

2. Select [Setup] > [TV settings] > [General

settings] > [Menu language].

3. Select a menu language from the list, then

press OK.

Audio language

If the TV channel broadcasts multiple or dual
audio languages, you can select your
preferred audio language.

1. While you watch TV, press OPTIONS.

2. For digital channels, select [Audio

language]. For analog channels, select [Dual
I-II]. Press OK to confirm your selection.

3. Select from the available languages, then

press OK.

You can set your preferred primary and
secondary audio languages to hear when
available.

EN 36

1. While you watch TV, press .

2. Select [Setup] > [Channel settings] >
[Languages].

3. Select [Primary audio language] or
[Secondary audio language] and select from
the available languages.

4. Press OK to confirm.

Subtitles on analog channels

1. While you watch an analog TV channel,
press TEXT.

2. Enter the three-digit page number of the
subtitles page, which is usually '888'.
If available, subtitles are switched on.

Subtitles on digital channels

1. While you watch a digital TV channel,
press OPTIONS.

2. Select [Subtitles], then press OK.

3. Select [Subtitles off], [Subtitles on] or

[Automatic], then press OK.

Subtitle language

When available, you can change the subtitle
language for digital channels.

1. While you watch TV, press

2. Select [Subtitle language], then select
from the available languages and press OK.
The subtitle language is changed for the
specific channel.

You can set your preferred primary and
secondary subtitle languages to display when
available.

1. While you watch TV, press

2. Select [Setup] > [Channel settings] >
[Languages].

3. Select [Primary subtitle language] or
[Secondary subtitle language] and select
from the available languages.

4. Press OK to confirm.

OPTIONS.

.

Universal access settings

Switch on

Some digital TV broadcasters provide special
audio and subtitle features for people who
are hearing or visually impaired. You can
switch these features on or off.

1. Press .

2. Select [Setup] > [TV settings] > [General

settings].

3. Select [Universal access] > [On] or [Off],

then press OK.

Set audio feedback

When you press a button on the remote
control or TV, you can set the TV to play a
beep.

1. While you watch TV, press

2. Select [Universal access] > [Key beep] >

[On], then press OK.

Hearing impaired access

To make sure that a hearing impaired audio
language is available, press OPTIONS,
then select [Audio language]. Languages that

support hearing impaired audio are indicated
with an ear-shaped icon.

Switch on hearing impaired audio and
subtitles

1. While you watch TV, press

2. Select [Universal access] > [Hearing

impaired].

3. Select a setting, then press OK.

 [Off]: Switch off hearing impaired

features.

 [On]: Switch on hearing impaired audio

and subtitles.

OPTIONS.

OPTIONS.

English

EN 37

Visually impaired access

To make sure that a visually impaired audio
language is available, press
then select [Audio language]. Languages that

support visually impaired audio are indicated
with an eye-shaped icon.

Select speakers or headphones
You can choose to hear the visually impaired
audio through the TV speakers, headphones,
or both.

1. While you watch TV, press

2. Select [Universal access] > [Visually
impaired].

3. Select a setting, then press OK.

 [Speakers]: Hear visually impaired

audio from speakers only.

 [Headphones]: Hear visually impaired

audio from headphones only.

 [Speakers + headphones]: Hear visually

impaired audio from speakers as well as
headphones.

 [Off]: Swich off visually impaired audio.

Note: If the EasyLink remote control is

switched on, you cannot select the Green
button. To switch off EasyLink, see Connect

your TV > Set up EasyLink devices > What
you need (Page 51).

Change volume for visually impaired audio

1. While you watch TV, press

2. Select [Universal access] > [Mixed
volume].

3. Press the Navigation buttons to change
the volume, then press OK.

Audio effects

1. Press

.

2. Select [Setup] > [Channel settings].

3. Select [Languages] > [Visually impaired]
> [Audio effects].

4. Select a setting, then press OK.

 [On]: Enable audio effects in the visually

impaired audio.

 [Off]: Disable audio effects in the

visually impaired audio.

OPTIONS,

OPTIONS.

OPTIONS.

Type of speech

1. Press

.

2. Select [Setup] > [Channel settings].

3. Select [Languages] > [Visually impaired]

> [Speech].

4. Select a setting, then press OK.

 [Descriptive]: Hear descriptive speech

in the visually impaired audio.

 [Subtitles]: Hear subtitles in the visually

impaired audio.

Other settings

TV demo

You can watch a demo to find out more
about the features on this TV.

1. While you watch TV, press

2. Select [Setup] > [Watch demos], then

press OK.

3. Select a demo, then press OK.

Home mode

Some TV settings may not be available in
Shop mode. To make sure that the correct
TV settings are applied, set the TV to Home

mode.

1. While you watch TV, press

2. Select [Setup], then press OK.

3. Select [TV settings] > [General settings]

> [Location].

4. Select [Home] or [Shop], then press OK.

5. Restart the TV.

.

.

EN 38

Update software

Check version

1. Press .

2. Select [Setup] > [Software settings] >
[Current software info], then press OK.

The current software version is displayed.
Caution: Do not install a lower version of

software than the current version installed
on your product. TP Vision cannot be held
liable or be made responsible for problems
caused by a software downgrade.

Update the software through one of these
methods:

 update with USB storage device
 update from digital broadcast
 update from the Internet

Update with USB

What you need

 A USB storage device that has at least

256 megabytes of storage space, is FAT
or DOS formatted, and has its write
protection disabled.

 Access to a computer with a USB

connector and Internet access.

 A file archiver program that supports

the ZIP file format: for example,
WinZip® for Microsoft® Windows®,
or StuffIt® for Macintosh®.

Note: Do not use a USB hard drive.
Download the latest software

1. Connect the USB flash drive to your
computer.

2. On your computer, launch a browser such
as Internet Explorer® or Safari®, and see

www.philips.com/support.

3. Find your TV and locate the software and
drivers available for your TV set. The
software upgrade is available as a
compressed file (*.zip).

4. If the software version is higher than the
version on your TV, click the software
upgrade link.

5. Accept the license agreement and

download the ZIP file to the USB flash drive.
Note: Some Internet browsers, such as

Mozilla® Firefox® or Google® Chrome®,
may download the ZIP file directly to your
computer. If this happens, copy the file to
your USB flash drive.

6. For Internet Explorer: Using a file

archiver, extract autorun.upg from the
downloaded ZIP file. Do not copy or place
the extracted file into a folder.

6. For Safari: When the download is

complete, autorun.upg is automatically
extracted from the ZIP file to your
computer. Copy the file to the USB flash
drive. Do not copy or place the file into a
folder.

7. Eject and disconnect the USB flash drive

from the computer.

Upgrade the TV software
Caution:

 Do not switch off the TV or remove

the USB flash drive during the software
upgrade.

 If a power failure occurs during the

upgrade, do not remove the USB flash
drive from the TV. The TV continues
the upgrade as soon as power is
restored.

 If an error occurs during the upgrade,

retry the upgrade from the beginning. If
the error reoccurs, contact Philips
Consumer Care.

English

EN 39

1. Remove all USB devices such as a Wi-Fi
adapter from the TV, then switch on the TV.

2. Connect the USB flash drive to the TV.
The software upgrade starts automatically.
The upgrade is complete when a notification
message appears on screen.

3. Before you restart the TV, disconnect the
USB flash drive from the TV.

4. Press

on the remote control — do not
press more than once.
The TV switches off, then back on again. The
upgrade is complete.

5. To prevent accidental updates to the TV
software, reconnect the USB flash drive to
your computer and delete autorun.upg.

Update from digital broadcast

When available, the TV can receive software
updates through digital broadcasts. When a
software update is received, you are
prompted to update the software. We
strongly recommend that you update the
software when prompted.

Follow the onscreen instructions.
If you do not update the TV software when

the update is received, you are prompted to
save the update file. To update the software
later:

1. Press .

2. Select [Setup] > [Software settings] >
[Local updates].

3. Select the file that you downloaded and
follow the onscreen instructions to complete
the update.

Update from the Internet

You can also update the TV software
directly from the Internet by connecting the
TV to the Internet. See Connect your TV >
Connect to a Network and the Internet
(Page 53).

1. Press

.

2. Select [Setup] > [Update software] >
[TV with Internet], then press OK.

3. Follow the onscreen instructions to start
the update.

When the update is complete, the TV
switches to standby and on again
automatically. Wait for the TV to switch
back on. Do not switch on the TV yourself.

Note:

 If the TV is connected to the Internet,

the TV displays the availability of new
software at startup.

 Philips may occasionally push a software

upgrade to your TV over the Internet.
Follow the onscreen instructions to
upgrade the TV software.

Reset all

You can reset all picture and sound settings
and reinstall all TV channels on your TV.

1. Press

2. Select [Setup] > [TV settings] > [General
settings] > [Reinstall TV], then press OK.

3. Follow the onscreen instructions.

.

EN 40

5 Connect your

TV

About cables

Cable quality

Before you connect devices to the TV, check
the available connectors on the device.
Connect the device to the TV with the
highest quality connection available. Good
quality connectors transfer picture and
sound better.

The connections shown in this user manual
are recommendations only. Other solutions
are possible. For more examples, visit

http://www.connectivityguide.philips.com.

Tip: If your device has only composite or

RCA connectors, use a composite (CVBS)
cable to connect the device to the CVBS/Y
connector on the TV.

HDMI

An HDMI connection has the best picture
and sound quality.

 An HDMI cable combines video and

audio signals. Connect HDMI for high­definition (HD) TV signals, and to
switch on EasyLink.

 An HDMI Audio Return Channel

(ARC) connector allows output of TV
audio to an HDMI ARC compliant
device.

 Connect HDMI cables shorter than 5

meters/16.4 feet.

HDMI

Y Pb Pr

Component video (Y Pb Pr) only transmits
video. For sound, also connect to Audio
Left/Right.

 The Y Pb Pr connection can handle

high-definition (HD) TV signals.

 Match the Y Pb Pr connector colors to

the cable plugs.

YPbPr

AUDIO L/R

English

EN 41

Connect antenna

Connect the antenna to the TV.

TV ANTENNA

Connect devices

Blu-ray or DVD disc player

Connect the disc player with an HDMI cable to the TV.

HDMI

Connect the disc player with a component video cable (Y Pb Pr) and an audio L/R cable to the TV.

AUDIO L/R

EN 42

YPbPr

TV receiver

Connect the digital TV receiver with an antenna cable to the TV.

TV ANTENNA

English

Connect the satellite or digital TV receiver with an HDMI cable to the TV.

HDMI

Connect the digital TV receiver with a component video cable (Y Pb Pr) and an audio L/R cable to
the TV.

AUDIO L/R

YPbPr

EN 43

Video recorder

Connect the recorder with an antenna cable to the TV.

TV ANTENNA

REC

Connect the recorder with an HDMI cable to the TV.

REC

HDMI

ARC

Connect the recorder with a component video cable (Y Pb Pr) and an audio L/R cable to the TV.

REC

AUDIO L/R

YPbPr

EN 44

Game console

Connect the game console with an HDMI cable to the TV.

HDMI

English

Connect the game console with a component video cable (Y Pb Pr) and an audio L/R cable to the
TV.

AUDIO L/R

YPbPr

Home theater

Connect an HDMI-ARC compliant home theater with an HDMI cable to the TV.

HDMI

ARC

EN 45

Connect the home theater with an HDMI cable and a coaxial audio cable to the TV.

HDMI

Digital

Audio Out

Connect the home theater with a component video cable (Y Pb Pr) and an audio L/R cable to the
TV.

AUDIO L/R

YPbPr

Digital camera

Connect the digital camera with a USB cable to the TV.

EN 46

USB

Digital camcorder

Connect the digital camcorder with an HDMI cable to the TV.

HDMI

English

Connect the digital camcorder with a component video cable (Y Pb Pr) and an audio L/R cable to
the TV.

AUDIO L/R

YPbPr

EN 47

Connect more devices

USB storage device

USB

Connect the USB hard drive with a USB
cable to the TV.

Computer

Connect the computer with an HDMI cable to the TV.

HDMI

USB

Connect the USB flash drive with a USB
cable to the TV.

EN 48

Connect the computer with a DVI-HDMI cable and an audio cable to the TV.

English

HDMI

AUDIO IN

DVI/VGA

Video call camera

Connect the Philips TV video camera - PTA317 (sold separately) with a USB cable to the TV.

USB

EN 49

Watch connected devices

Select a device

Before you can watch a device, connect the
device to the TV. See Connect your TV >

Connect devices (Page 42).
Select a device with SOURCE

1. Press
control, or INPUT on the TV.

2. Select a device, then press OK.
Select a device from Home menu

1. Press .

2. Select [Source], then press OK.

3. Select a device, then press OK.

Update the source list

If you add or remove a device, update the
source list.

1. Press SOURCE.

2. Press

3. Select [Scan connections], then press OK.

4. Follow the onscreen instructions.

Change device settings

Change the device type

You can change the device type to easily
access it from the Source menu.

1. Press

2. Select the device, then press [Device
type].

3. Select a suitable device type, then press

OK.

Rename a device

You can rename a device after it is
connected to the TV.

1. Press

2. Select the connector, then press
[Rename].

3. Use the onscreen keypad to enter a new
name.

4. When complete, select [Done], then
press OK.

SOURCE on the remote

OPTIONS.

SOURCE.

SOURCE.

Reset device settings

You can reset the type and name of the
device to default settings.

1. In the [Source] menu, select the device
and press OPTIONS.

2. Select [Original name and icon], then
press OK.

Set up EasyLink devices

What you can do

You can get the most out of your HDMI­CEC-compliant devices with Philips EasyLink
enhanced control features. Connect your
HDMI-CEC compliant devices through
HDMI to your TV and control them at the
same time with your TV remote control.

Note: Other brands describe HDMI-CEC
functionality differently. Some examples are
Anynet (Samsung), Aquos Link (Sharp) or
BRAVIA Sync (Sony). Not all brands are fully
compatible with Philips EasyLink.

After you switch on Philips EasyLink, the
following features are available:

One-touch play
When you play an HDMI-CEC compliant
device, the TV switches on from standby and
switches to the correct source.

One-touch standby
When you press
control, the TV and all HDMI-CEC
compliant devices switch to standby mode.

Auto switch off inactive devices
If a HDMI-CEC compliant device has been
inactive for some time, it switches to standby
mode.

EasyLink remote control
You can control multiple HDMI-CEC
compliant devices with your TV remote
control.

on the TV remote

EN 50

System audio control
If you connect an HDMI-CEC compliant
device that includes speakers through the
HDMI ARC connector, you can choose to
hear the TV audio from those speakers
instead of the TV speakers.

Retain picture quality
If your TV picture quality is affected by the
picture-processing features of other devices,
you can switch on Pixel Plus Link to retain
picture quality.

Maximize display for subtitled video
Some video subtitles can create a separate
subtitle bar under the video, which limits the
video display area. To maximize the video
display area, you can switch on auto subtitle
shift and display the subtitles on the video
image.

What you need

 Connect a HDMI-CEC compliant

device to the TV. You can connect
more than one HDMI-CEC device. See
Connect your TV > Connect devices
(Page 42).

 Configure each HDMI-CEC compliant

device properly.

 Switch on EasyLink.

Switch on EasyLink

1. Press

.

2. Select [Setup] > [TV settings] > [General
settings] > [EasyLink].

3. Select [EasyLink] > [On], then press OK.

Control devices

If you connect multiple HDMI-CEC devices
that support this setting, you can control all
such devices through the TV remote control.

Note: This is an advanced setting. Devices
that do not support this setting cannot
respond to the TV remote control.

1. Press

2. Select [Setup] > [TV settings] > [General

settings] > [EasyLink] > [EasyLink remote
control].

3. Select [On] or [Off], then press OK.

.

Tips:

 To switch back to TV control, press

,

then select [Watch TV].

 To control another device, press

,
then select the device from the Home
menu.

EasyLink buttons
You can control HDMI-CEC compliant
devices with these buttons on the TV
remote control:

: Switch the TV and the connected



device on or to standby.

 Play buttons: Control video or music

play.

 Numeric buttons: Select a title, chapter

or track.

 OK: Start, pause or resume play on the

connected device, activate a selection,
or access the device menu.



: Display the TV Home menu.

Switch off connecting devices
You can also set the TV to switch off the
connecting HDMI-CEC compliant devices if
they are not the active source. The TV
switches the connecting device to standby
after 10 minutes of inactivity.

1. Press

.

2. Select [Setup] > [TV settings] > [General
settings] > [EasyLink].

3. Select [Auto switch off devices] > [On],
then press OK.

Select speaker output

If a connected device is HDMI Audio Return
Channel (HDMI ARC) compliant, you can
output TV audio through an HDMI cable.
Additional audio cables are not required.
Make sure you connect the device to the
HDMI ARC connector on the TV. See
Connect your TV > About cables > HDMI
(Page 41).

Switch on HDMI ARC

1. Press .

2. Select [Setup] > [TV settings] > [Sound]
> [Advanced] > [HDMI 1 - ARC].

English

EN 51

3. Select one of the following, then press
OK.

 [On]: Hear the TV audio through the

connected HDMI-ARC compliant
device.

 [Off]: Hear the TV audio through the

TV speakers, or through a device
connected through the digital audio out
connector.

Note: Make sure that all HDMI-CEC settings
are properly set up on the connected device.

Set up TV speakers

1. Press

.

2. Select [Setup] > [TV settings] > [Sound]
> [Advanced] > [TV speakers].

3. Select an option, then press OK:

 [Off]: Switch off TV speakers.
 [On]: Switch on TV speakers.
 [EasyLink]: Switch off TV speakers, and

stream TV audio to a connected
HDMI-CEC audio device.

 [EasyLink autostart]: When a HDMI-

CEC audio device is connected,
automatically switch off TV speakers
and stream TV audio to the device.

Change TV audio streaming
You can switch audio between TV speakers
and a connected amplifier at any time.

1. Press

OPTIONS.

2. Select [Picture and sound] > [Speakers].

3. Select one of the following, then press
OK.

 [TV]: On by default.

Stream TV audio through TV and the
connected HDMI-CEC audio device
until the connected device switches to
system audio control. TV audio is then
streamed through the connected
device.

 [Amplifier]: Stream audio through the

connected HDMI-CEC device. If system
audio mode is not enabled on the
device, audio continues to stream from
the TV speakers. If [EasyLink autostart]
was selected, the TV prompts the
connected device to switch to system
audio mode.

Retain picture quality

If your TV picture quality is affected by the
picture-processing features of other devices,
you can switch on Pixel Plus Link.

Switch on Pixel Plus Link

1. Press

.

2. Select [Setup] > [TV settings] > [General
settings] > [EasyLink].

3. Select [Pixel Plus Link] > [On], then press

OK.

Maximize video display

Some subtitles create a separate subtitle bar
under the video that limits the video display
area. To maximize the video display area,
you can switch on auto subtitle shift. The
subtitles then display over the video image.

Switch on auto subtitle shift

1. Press .

2. Select [Setup] > [TV settings] > [General
settings] > [EasyLink].

3. Select [Auto subtitle shift] > [On], then
press OK.

EN 52

Connect to a network and
the Internet

Connect

Internet

English

What you can do

View Media

If you connect the TV to a home network,
you can play photos, music and videos from
your computer. See Use your TV > Play

multimedia files (Page 15).
Smart TV

If you connect the TV to a home network
with an Internet connection, you can browse
Smart TV. Smart TV offers Internet services
and websites tailored to your TV. Play music
and videos, consult infotainment, rent movies
and much more. See Use your TV > Smart

TV (Page 18).

What you need

Warning: This TV complies with the EMC
directive only when you use a shielded
Cat5 Ethernet cable.

 A computer network that includes:

a) A universal plug-and-play (UPnP)
router and
b) A computer with one of these
operating systems: Microsoft Windows
XP, Microsoft Windows Vista, Mac OS
X, or Linux.

 To connect your TV to computers, you

need to install and configure a media
server on your computer. See Use
your TV > Play multimedia files (Page

15).

 To connect your TV to the Internet,

you also need a high-speed connection
to the Internet.

TV

Router

PC

You can connect this TV to your home
network through a wired or wireless
connection.

 For a wired connection, see Connect

your TV > Connect to a network and
the Internet > Wired connection

(Page 53).

Internet

TV

Router

PC

 For a Wi-Fi ready connection, see

Connect your TV > Connect to a
network and the Internet > Wi-Fi
ready (Page 54).

Wired connection

1. Switch on the router and switch on its
DHCP setting.

2. Connect the router with an Ethernet
cable to the TV.

3. Press

, then select [Setup].

4. Select [Connect to network], then press
OK.

5. Follow the onscreen instructions to install
the network.

6. Wait for the TV to find the network
connection.

7. If you are prompted, agree to the End
User License Agreement.

EN 53

Wi-Fi ready

With the Philips wireless USB adapter
PTA127, you can connect the TV to your
home network wirelessly.

Note:
The wireless network operates in the same

2.4GHz frequency spectrum as common
household devices, such as Dect phones,
microwave ovens or Bluetooth devices,
which can cause Wi-Fi interference. Move
these devices away from the TV.

 To reduce network traffic, switch off

unused network equipment in the
home network.

 Reception quality depends on the

location of the wireless router and the
local Internet service provider.

 While you play video over your

wireless home network, we
recommend that you use an IEEE

802.11 N router. The connection speed
may differ according to the operating
environment of your wireless home
network.

Start wireless setup

1. Switch on your wireless network router.

2. Connect the Philips USB adapter PTA127
to a USB connector on the TV.
The wireless installation starts automatically.

3. Follow the onscreen instructions.
Tip: Keep the wireless USB adapter

connected to the TV.
WPS - Wi-Fi Protected Setup

1. If your router supports Wi-Fi Protected
Setup (WPS), press the WPS button on the
router.

2. After 2 minutes, select [WPS] on the TV,
then press OK.
The TV connects to your network. This
takes about 2 minutes.

Most new wireless routers have the WPS
system and carry the WPS logo. The WPS
system uses WPS security encryption and
cannot be combined with devices on your
network that use the WEP security
encryption. If you still need the WEP (Wired
Equivalent Privacy) devices in your network,
install with [Scan] > [Custom].

Scan for routers

If you have several routers in your network,
you can select the network you need.

1. To select a specific network router, press
[Scan] on the first page of the installation.

The routers with WPS and the strongest
signal are shown first in the list on screen.

2. Select the router you need, then press
OK.

 If you are connecting to a WPS router,

select [WPS] on the TV.

 If you want to set the PIN code in your

router software to connect, select
[WPS pin] and note down the code.

 To enter the encryption key manually,

select [Standard], then enter the key
when prompted.

Set secured connection with WPS PIN

1. To set secured connection, select the
[WPS pin] and press OK.

2. Write down the 8-digit PIN code shown
on TV, then enter it in the router software
on your PC.
To find out where to enter the PIN code,
read the router manual.

Set secured connection with WPA
encryption

If you have WPA security on your router,
enter the pass phrase with the remote
control.

1. To enter the encryption key (the security
key) manually, select [Standard], then press
OK.

2. To access the onscreen keyboard, select
the text entry field, then press OK.

EN 54

Set secured connection with WEP
encryption

If you have WEP security encryption, the TV
asks for the WEP encryption key in
hexadecimal numbers.

1. Locate the hexadecimal key in the router
software on your PC and make a note of the
first key in the WEP keys list.

2. Enter it on TV with the remote control.
If the security key is accepted, the TV is
connected with the wireless router.

3. If prompted, agree to the End User
License Agreement.

Network settings

TV network name

If you have more than one TV in your home
network, you can rename this TV to give it a
unique name.

1. Press

2. Select [Setup] > [Network settings] >
[TV network name], then press OK.

3. Use the onscreen keyboard or the remote
control keypad to enter the name.

Switch on Miracast
This TV is a Miracast-certified TV. To
seamlessly display content from a Wi-Fi
device on your TV, switch on Miracast.

1. Press

2. Select [Setup] > [Network settings] >
[Wi-Fi Miracast].

3. Select [On], then press OK to enable
Miracast.

Tip: To clear the history of all Wi-Fi Miracast
devices, select [Setup] > [Network settings]
> [Clear Wi-Fi Miracast devices].

Switch on remote recording
This TV supports remote recording
scheduled from a Wi-Fi device.

Note: If you switch on remote recording,
the TV consumes more power in standby.

1. Press

2. Select [Setup] > [Network settings] >
[MyRemote Recording].

3. Select [On], then press OK.

.

.

.

English

EN 55

6 Troubleshooting

General issues

The TV does not switch on:

 Disconnect the power cable from the

power outlet. Wait for one minute
then reconnect it.

 Make sure that the power cable is

securely connected.

When you are turning the TV on, off or to
standby, you hear a creaking sound from
the TV chassis:

No action is required. The creaking sound is
due to the normal expansion and
contraction of the TV as it cools and warms
up. This does not affect performance.

The TV does not respond to remote
control or TV controls when switched on:

The TV requires some time to start up.
During this time, the TV does not respond
to the remote control or TV controls. This is
normal behavior.

If the TV continues to be unresponsive to
the remote control, view the remote control
sensor through a digital camera -- if you
press any button on the remote control and
notice red flickering at the sensor, the
remote control is working but the TV may
need to be checked by Philips Consumer
Care. This troubleshooting procedure is not
applicable to remote controls that are paired
wirelessly with the TV.

When the TV is in standby, a startup splash
screen is displayed, then TV returns to
standby mode:

This is normal behavior. When the TV is
disconnected and reconnected to the power
supply, the startup screen is displayed at the
next startup.
To switch on the TV from standby, press
on the remote control or press any key on
the TV.

The standby light on the TV blinks red:
Disconnect the power cable from the power
outlet. Wait until the TV cools down before
you reconnect the power cable. If the
blinking reoccurs, contact Philips Consumer
Care.

The TV audio is in the wrong language:
If you select audio language via

OPTIONS,
the TV resets to the default language when
you change channels or switch off the TV.
To retain the selected language, change your
audio language by pressing

, then selecting
[Setup] > [Channel settings] > [Languages]
> [Primary audio language] or [Secondary

audio language].
The TV or Smart TV menu is in the wrong

language:

Change the menu to your preferred
language.
For more information, see Change your TV

settings > Language settings > Menu
language (Page 36).

You forgot the 4-digit code to unlock the
channel blocking feature (child lock):

Enter ‘8888’.
You want to upgrade your TV software:

Visit www.philips.com/support and
download the latest software package for
your TV. Software installation instructions
and release notes indicating what's been
updated are also available at the site. Full
instructions on how to upgrade your TV

software are also available at Change your
TV settings > Update software (Page 39).

EN 56

Channel issues

You want to install TV channels:
See Change your TV settings > Automatic
installation (Page 34) for instructions on

installing analog or digital channels.

No digital channels were found during the
installation:

 See the technical specifications to make

sure that your TV supports DVB-T or
DVB-C in your country.

 Make sure that all cables are properly

connected and that the correct
network is selected.

Previously installed channels do not appear
in the channel list:

Make sure that the correct channel list is
selected.

You want to rearrange or reorder the
channel list:

After channels are installed, they appear in
the channel list. For information about
managing channel lists, including rearranging
channels, see Watch TV > Manage channel

lists (Page 12).

Picture issues

The TV is on, but there is no picture or the
picture is distorted:

 Make sure that the antenna is properly

connected to the TV.

 Make sure that the correct device is

selected as the display source.

 Make sure that the external device or

source is properly connected.

There is sound but no picture:
Make sure that the picture settings are set
correctly.

There is poor TV reception from an
antenna connection:

 Make sure that the antenna is properly

connected to the TV.

 Loud speakers, unearthed audio

devices, neon lights, high buildings, and
other large objects can influence
reception quality. If possible, try to
improve the reception quality by
changing the antenna direction or
moving devices away from the TV.

 If reception on only one channel is

poor, fine-tune this channel.

There is poor picture quality from
connected devices:

 Make sure that the devices are

connected properly.

 Make sure that the picture settings are

set correctly.

The TV did not save your picture settings:
Make sure that the TV location is set to

Home. You can change and save settings in
this mode.

The picture does not fit the screen; it is
too big or too small:

Change to a different picture format.

The picture format keeps changing with
different channels:

Instead of the picture format [Auto zoom],
select a different picture format.

The picture position is incorrect:
Picture signals from some devices may not fit
the screen correctly. Check the signal output
of the device.

The picture from broadcasts is scrambled:
You may need a Conditional Access Module
to access content. Check with your service
operator.

An "e-sticker" banner displaying
information appears on the TV display:

The TV is in [Shop] mode. To remove the
e-sticker, set the TV to [Home] mode, then
restart the TV. See Change your TV settings

> Other settings > Home mode (Page 38).
The computer display on the TV is not

stable:

 Make sure that your PC uses the

supported resolution and refresh rate.
See Specifications > Display
resolutions (Page 60).

 Change the TV picture format to

[Unscaled].

English

EN 57

Sound issues

There is picture but no sound from the TV:

If no audio signal is detected, the TV
automatically switches the audio output off
— this does not indicate malfunction.

 Make sure that all cables are properly

connected.

 Make sure that the volume is not

muted or set to zero.

 Make sure that the TV speakers setting

is selected. Press
[Picture and sound] > [Speakers], and
then select [TV].

 Make sure that the TV audio output is

connected to the audio input on the
HDMI-CEC enabled or EasyLink
compliant home theater device. Sound
should be heard from the home theater
speakers.

 Some devices may require you to

manually enable HDMI audio output. If
HDMI audio is already enabled, but you
still do not hear audio, try changing the
digital audio format of the device to
PCM (Pulse Code Modulation). Refer
to the documentation accompanying
your device for instructions.

There is picture but sound quality is poor:
Make sure that the sound settings are
correctly set.

OPTIONS, select

 If you use an HDMI-to-DVI adapter or

HDMI to DVI cable, make sure that an
additional audio cable is connected to
AUDIO L/R or AUDIO IN (mini-jack
only).

You cannot use EasyLink features:
Make sure that your HDMI devices are
HDMI-CEC compatible. EasyLink features
only work with devices that are HDMI-CEC
compatible.

If an HDMI-CEC compliant audio device is
connected to the TV and the TV does not
display any mute or volume icon when the
volume is muted, increased or decreased:

When a HDMI-CEC audio device is
connected this behavior is normal.

USB device content is not displayed:

 Make sure that the USB storage device

is set to Mass Storage Class compliant,
as described in the storage device's
documentation.

 Make sure that the USB storage device

is compatible with the TV.

 Make sure that the audio and picture

file formats are supported by the TV.

Audio and picture files on your USB
storage device do not play or display
smoothly:

The transfer performance of the USB
storage device may limit the data transfer
rate to the TV which causes poor playback.

Connection issues

There are problems with HDMI devices:

 Note that HDCP (High-bandwidth

Digital Content Protection) support can
delay the time taken for a TV to display
content from an HDMI device.

 If the TV does not recognize the HDMI

device and no picture is displayed,
switch the source from one device to
another and back again.

 If there are intermittent sound

disruptions, make sure that output
settings from the HDMI device are
correct.

EN 58

Network issues

You want to establish a wireless
connection between your TV and home
network:
Refer to Connect your TV > Connect to a
network and the Internet > Wi-Fi Ready
(Page 54) for instructions on how to

connect your TV wirelessly to your home
network.

Smart TV does not work:
Check that the router is properly connected
to the TV, and that your router has open
access to the Internet. If your router has a
firewall or security settings, make sure that it
allows Smart TV data to pass through ­check your router documentation for details.

Internet access via Smart TV is slow:

 Try to improve the signal quality

between the router and TV if you are
accessing the Internet wirelessly. Refer
to the router's documentation for
details.

 Always use a fast broadband wherever

possible.

 Update your TV with the latest

software to ensure browsing speed is
optimal.

Your network is slow:

If you are accessing your PC wirelessly, refer
to the router's documentation to improve
the signal quality between the router and
TV.

Wireless network is distorted or not
found:

 Make sure that the wireless network is

not disturbed by microwave ovens,
DECT phones, or other neighboring
Wi-Fi devices.

 If the wireless network is not working,

try a wired network connection.

 Make sure that the firewalls in your

network allow access to the TV
wireless connection.

Contact Philips

Warning: Do not attempt to repair the TV
yourself. This may cause severe injury,
irreparable damage to your TV or void
your warranty.

If are not able to resolve your problem, refer
to the frequently asked questions (FAQs) for
this TV at www.philips.com/support. You
can also consult and contribute to the Philips
TV community at

www.supportforum.philips.com.

If you wish to speak with or email a Philips
representative, contact the Philips Consumer
Care in your country. You can find the
contact details in the leaflet accompanying
this TV or at www.philips.com/support.

Take note of your TV model and serial
number before you contact Philips. These
numbers are printed on the back of the TV
and on the packaging.

English

EN 59

7 Specifications

Power and reception

Product specifications are subject to change
without notice.

Power

 Mains power: AC 220-240V (50-60Hz)
 Standby power consumption: < 0.3 W
 Ambient temperature: 5 to 40 degree

Celsius

 For power consumption, see the

product specifications at

www.philips.com/support.

The power rating stated on the product
typeplate is the power consumption for this
product during normal household use (IEC
62087 Ed.2). The maximum power rating,
stated between brackets, is used for
electrical safety (IEC 60065 Ed. 7.2).

Reception

 Antenna input: 75 ohm coaxial (IEC75)
 TV system: DVB COFDM 2K/8 K
 Video playback: NTSC, PAL, SECAM*
 Digital TV: MPEG-4, DVB-T

(Terrestrial), DVB-T2*, DVB-C (Cable)

 Tuner bands: VHF, UHF, S-Channel,

Hyperband

* Available on certain models only.

Sound

 Output power (RMS): 20 W @ 10%

THD

 Clear Sound
 Mono / Stereo / Secondary audio

programming

Display resolutions

Computer formats - HDMI
(Resolution - refresh rate)

640 x 480 - 60 Hz
800 x 600 - 60 Hz
1024 x 768 - 60 Hz
1280 X 720 - 60 Hz
1280 X 768 - 60 Hz
1280 x 1024 - 60 Hz
1360 x 768 - 60 Hz
For Full HD TV only:
1680 x 1050 - 60 Hz
1920 x 1080 - 60 Hz
Video formats (Resolution - refresh rate)
480i - 60 Hz
480p - 60 Hz
576i - 50 Hz
576p - 50 Hz
720p - 50Hz, 60 Hz
1080i - 50Hz, 60 Hz
1080p - 24Hz, 25Hz, 30Hz, 50Hz, 60 Hz

Multimedia

Display and sound

Picture / Display

 Display type: LED backlight HD/Full HD
 Diagonal size:

- 81 cm / 32 inches

- 99 cm / 39 inches

- 107 cm / 42 inches

- 117 cm / 46 inches

 Aspect ratio: 16:9 (widescreen)
 Panel resolution:

- Full HD: 1920x1080p

- HD: 1366 x 768

 Picture enhancement: Digital Crystal

Clear

 Perfect Motion Rate (PMR): 100 Hz

EN 60

Note: Multimedia file names must not
exceed 128 characters.

Supported multimedia connections

 USB: Connect only those USB devices

that consume 500mA of power or less.

- NTFS, FAT 16 (Read only)

- FAT 32

 Ethernet LAN RJ-45

Supported image files

 JPEG: *.jpg, *.jpeg, *.mpo
 GIF (87a, 89a): *.gif
 PNG: *.png
 BMP: *.bmp, *.dib
 JPS: *.jps
 PNS: *.pns
 BMS: *.bms

Supported audio/video formats

File Extensions Container

.mpg
.mpeg
.vob

.ts TS

Video codec

MPEG-1

MPEG-2

PS

MPEG-4 ASP

H.264

MPEG-2

MPEG-4 ASP

H.264

MVC

Supported audio/video formats

File Extensions Container

.ts

.m2ts

.mts

.mt2

.ts

.m2ts

.mts

M2TS

TTS

AVCHD

Video codec

MPEG-2

MPEG-4 ASP

H.264

MVC

MPEG-2

MPEG-4 ASP

H.264 1920x1088

Supported audio/video formats

File Extensions Container

.ts

.m2ts

.mts

.m4v M4V H.264 1920x1088

.ism/Manifest

.mpd

Video codec

AVCHD

H.264 1920x1088

frag MP4

Supported audio/video formats

File Extensions Container

.mp4 MP4

.mkv
.mk3d

Video codec

MPEG-4 ASP 1920x1088 30

H.264 1920x1088 30

MVC 30

WMV9/VC1 1920x1088 30

MPEG-4 ASP 1920x1088 30

MKV

H.264 1920x1088

Maximum

resolution

1920x1088

1920x1088 Yes Yes Yes No

1920x1088 Yes Yes Yes No

1920x1088 Yes Yes Yes No

1920x1088

1920x1088 Yes Yes Yes No

1920x1088

1920x1080i @
field rate = 50,

60Hz

1920x1080p @

frame rate = 24,

25, 30Hz

1280x720p @

frame rate = 50,

60Hz

Maximum

resolution

1920x1088 30

1920x1088 30 Yes Yes No No No

1920x1088 30 Yes Yes No No No

1920x1080i @
field rate = 50,

60Hz

1920x1080p @

frame rate = 24,

25, 30Hz

1280x720p @

frame rate = 50,

60Hz

1920x1088 30

1920x1088 30 Yes Yes No No No

Maximum

resolution

1920x1080i @
field rate = 50,

60Hz

1920x1080p @

frame rate = 24,

25, 30Hz

1280x720p @

frame rate = 50,

60Hz

1920x1080i @
field rate = 50,

60Hz

1920x1080p @

frame rate = 24,

25, 30Hz

1280x720p @

frame rate = 50,

60Hz

Maximum

resolution

1920x1080i @
field rate = 50,

60Hz

1920x1080p @

frame rate = 24,

25, 30Hz

1280x720p @

frame rate = 50,

60Hz

Max. Bit Rate

Max. Frame Rate

(fps)

25p, 30p, 50i, 60i

25p, 30p, 50i, 60i

25p, 30p, 50i, 60i

25p, 30p, 50p, 60p,

60i

25p, 30p, 50i, 60i

25p, 30p, 50i, 60i

25p, 30p, 50p, 60p,

60i

-Yes

Max. Bit Rate

Max. Frame Rate

(fps)

25p, 30p, 50i, 60i

25p, 30p, 50i, 60i

25p, 30p, 50p, 60p,

60i

-

25p, 30p, 50i, 60i

25p, 30p, 50i, 60i

25p, 30p, 50p, 60p,

60i

Max. Bit Rate

Max. Frame Rate

(fps)

25p, 30p, 50p, 60p,

60i

25p, 30p, 50p, 60p,

60i

Max. Bit Rate

Max. Frame Rate

(fps)

25p, 30p, 50i, 60i

-

30p, 60i

25p, 30p, 50i, 60i

Audio codec USB

(Mbps)

30

MPEG-1 (L1&L2),

30

MPEG-1,2,2.5 L3,

AAC/HE-AAC (v1&v2),

30

DVD-PCM , Dolby Digital

30

30

30

30

MPEG-1 (L1&L2), MPEG­1,2,2.5 L3, AAC/HE-AAC

(v1&v2), Dolby Digital,

Dolby Digital Plus

Dolby Pulse

30

Audio codec USB

(Mbps)

MPEG-1 (L1&L2), MPEG­1,2,2.5 L3, AAC/HE-AAC

(v1&v2), Dolby Digital,

Dolby Digital Plus,

Dolby Pulse

30 Yes Yes No No No

MPEG-1 (L1&L2), MPEG­1,2,2.5 L3, AAC/HE-AAC

(v1&v2), Dolby Digital,

Dolby Digital Plus,

30 Yes Yes No No No

Dolby Pulse

Audio codec USB

(Mbps)

MPEG-1 (L1&L2), MPEG­1,2,2.5 L3, AAC/HE-AAC

30 Yes Yes No No NoMVC -

(v1&v2), Dolby Digital,

Dolby Digital Plus,

Dolby Pulse

30 AAC Yes Yes Yes Yes No

30 No No Yes Yes Yes

AAC/HE-AAC (v1&v2),

Dolby Digital,
Dolby Digital Plus,
WMA, WMA-PRO

30 No No Yes Yes YesMVC -

Audio codec USB

(Mbps)

AAC/HE-AAC (v1&v2),

Dolby Digital,
Dolby Digital Plus,
WMA, WMA-PRO

MPEG-1 (L1&L2), MPEG­1,2,2.5 L3, AAC/HE-AAC

(v1&v2), Dolby Digital,

Dolby Digital Plus,

30

WMA, WMA-PRO

Yes Yes Yes No

Yes Yes Yes No

Yes Yes Yes No

Yes Yes No No No

Yes Yes No No No

Yes

Yes

Yes

Yes

Yes

Yes

CE-

Media
server

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes Yes Yes No

Media
server

Media
server

Media
server

Yes

Yes

Yes

Yes

Yes

Yes

HTML

HTML

HTML

HTML

CE-

CE-

CE-

Yes

Yes

Yes

Yes

No

No

HTML5 YouTube

HTML5 YouTube

HTML5 YouTube

HTML5 YouTube

Yes

Yes

Yes

Yes

No

No

English

Yes

No

No

No

No

No

EN 61

Supported audio/video formats

File Extensions Container

.asf

.wmv

.avi

.xvid

.webm

.swf

.divx

WebM

SWF

DMF

(DIVX)

Video codec

MPEG-2

ASF

MPEG-4 ASP

WMV9/VC1

MPEG-4 ASP

AVI

DivX 3.11

VP8

Contains FLV

MPEG-4 ASP

DivX 3.11

Supported audio/video formats

File Extensions Container

.3gp
.3g2

.mov

.qt

Video codec

3GP

H.264

H.263 30 Yes Yes No No No

QuickTime - - - 30 - Yes Yes No No No

Supported audio formats

File Extensions Container

.mp3 MP3 - - 48 384 MPEG-1,2,2.5 L3 Yes Yes Yes Yes No

.wma

.asf

.wma - - 96 768 WMA, WMA Pro Yes Yes Yes Yes No

.lpcm (PC)
.pcm (PC)

.wav (PC) LPCM - - 192 768 LPCM Yes Yes No No No

.aif (mac)
.aiff (mac)

.aac
.mp4
.m4a

.pls
.m3u

.m4a M4A - - Yes Yes Yes Yes NoAAC, HE-AAC (v1&v2)48 1024

Video codec Frequency (kHz)

WMA
(V2 up

- - 48 192 WMA Yes Yes Yes Yes No

toV9.2)

WMA Pro

LPCM - - 192 768 LPCM No Yes No No No

LPCM - - 192 768 LPCM Yes Yes No No No

AAC - - 48 1024 AAC, HE-AAC (v1&v2) Yes Yes Yes Yes No

Playlists - - - - - Yes Yes No No No

Supported audio formats

File Extensions Container

.amr

.ogg
.oga

Video codec Frequency (kHz)

AMR-NB

(Smart TV

--

only)

Ogg - - 48 498

Supported subtitle formats

Format File Extension USB Media Server CE-HTML HTML5 YouTube

SRT .srt Yes No No No No

MKV/SRT - Yes Yes No No No

SUB .sub Yes No No No No

TXT .txt Yes Yes No No No

Substation alpha V4 .ssa Yes Yes No No No

Advanced substation alpha

V4+

DVB - Yes Yes No No No

SAMI .smi .sami Yes No Yes Yes No

XSUB, XSUB+

TTML .ttml No No Yes Yes No

.ass Yes Yes No No No

.avi

.divx

Maximum

Max. Frame Rate

resolution

1920x1088

25p, 30p, 50i, 60i

1920x1088

25p, 30p, 50i, 60i

1920x1088

1920x1088

1920x1088

1920x1088

1920x1088

1920x1088

Maximum

resolution

1920x1088

1920x1088

1920 x 1088 30p

Maximum

resolution

Maximum

resolution

30p, 60i

25p, 30p, 50i, 60i

30p, 60i

-

25p, 30p, 50i, 60i

30p, 60i

Max. Frame Rate

25p, 30p, 50i, 60i

25p, 30p, 50p, 60p,

Yes N o No N o N o

Max. Bit Rate

(fps)

-

Max. Bit Rate

(fps)

60i

Max. Bit Rate

Max. Bit Rate

8

16

Audio codec USB

(Mbps)

20

MPEG-1 (L1&L2), MPEG­1,2,2.5 L3, AAC/HE-AAC

20

(v1&v2), Dolby Digital Plus,

Dolby Digital, WMA,

WMA-PRO

20

MPEG-1 (L1&L2), MPEG-

4

MPEG-1 (L1&L2), MPEG­1,2,2.5 L3, AAC/HE-AAC
(v1&v2), Dolby Digital Plus,

Dolby Digital, WMA,

4

WMA-PRO

Ogg Vorbis

5

30

MPEG-1 (L1&L2), MPEG-

20

1,2,2.5 L3, AAC/HE-AAC
(v1&v2), Dolby Digital Plus,

Dolby Digital, WMA,

20

WMA-PRO

Audio codec USB

(Mbps)

30

AAC/HE-AAC (v1&v2),

30 Yes Yes No No No

Audio codec USB

(Mbps)

Audio codec USB

(Mbps)

12.8

6.6

8.85

12.65

14.25

15.85

18.25

19.85

Ogg Vorbis

Yes Yes Yes Yes No

Yes Yes Yes Yes No

Yes Yes Yes Yes No

Yes Yes No No No

Yes Yes No No No

Yes Yes Yes Yes No

No No No No Yes

-

Yes No No No No

Yes No No No No

Yes Yes No No NoMPEG-4 ASP

AMR

AMR Yes Yes No No No

Yes Yes No No No

Media
server

Media
server

Media
server

Media
server

HTML

HTML

HTML

HTML

CE-

CE-

CE-

CE-

HTML5 YouTube

HTML5 YouTube

HTML5 YouTube

HTML5 YouTube

EN 62

Character encoding

 Windows-1250 (CP-1250): Central

Europe and Eastern Europe Latin
(Czech, Hungarian, Polish, Slovak,
Slovenian, Croatian, Romanian, Serbian)

 Windows-1251 (CP-1251): Cyrillic
 Windows-1252 (CP-1252): Western

Europe Latin

 Windows-1253 (CP-1253): Greek
 Windows-1254 (CP-1254): Turkish
 UTF-8: Multi-byte character encoding

for Unicode

Supported DLNA-compliant media server
software

 Windows Media Player (Microsoft

Windows)

 Twonky Media (Microsoft Windows,

Mac OS X)

 Sony Vaio Media Server (Microsoft

Windows)

 TVersity (Microsoft Windows)
 Nero MediaHome
 DiXiM (Microsoft Windows XP)
 Macrovision Network Media Server

(Microsoft Windows)

 Fuppes (Linux)
 uShare (Linux)

 Headphones: stereo 3.5mm mini-jack

Help version

UMv 420813130301 - 20130118

English

Connectivity

Rear

 HDMI 1 ARC: HDMI Audio Return

Channel

 HDMI 2
 AUDIO IN (DVI): stereo 3.5mm mini-

jack

 NETWORK: Ethernet LAN RJ-45
 SERV. U: Service port
 CVBS/Y, Pb, Pr, Audio L/R: Composite

video and audio

 DIGITAL AUDIO OUT: Coaxial
 TV ANTENNA: 75 ohm coaxial (IEC)

Side

 HDMI
 USB 2
 USB 1

EN 63

8 Index

A

amplifier, select output • 51

analog channels, fine-tune • 35

analog channels, install • 34

analog channels, subtitles • 37

audio language • 36

auto subtitle shift • 52

Auto switch off, devices • 51

C

cables • 41

channel list • 12

channel list, copy • 35

channels • 12

channels, favorites • 12

channels, fine-tune (analog) • 35

channels, hide or unhide • 12

channels, install (analog) • 34

channels, install (automatic) • 34

channels, install (digital) • 35

channels, logo • 12

channels, reinstall • 40

channels, rename • 12

channels, sort • 12

channels, switch • 12

channels, update • 35

child lock • 31

clock • 30

codecs, supported • 60

computer, play files • 15

connect, computer • 48

connect, digital camcorder • 47

connect, digital camera • 46

connect, disc player • 42

connect, external hard disk • 48

connect, game console • 45

connect, home network • 53

connect, home theater • 45

connect, Internet • 53

connect, recorder • 44

connect, TV receiver • 43

connect, USB device • 48

connect, video call camera • 49

connected device, rename • 50

connectivity • 63

connectivity guide • 8

connectors • 41

contact Philips • 8

controls • 9

D

demo • 38

devices, watch • 50

digital camcorder • 47

digital camera • 46

digital channels, install • 35

digital channels, subtitles • 37

digital radio • 12

disc player, connect • 42

display resolutions • 60

display specifications • 60

DivX VOD • 17

DLNA • 15

DTVi • 20

E

EasyLink • 50

EasyLink, controls • 51

EasyLink, enable • 51

EasyLink, features • 50

EasyLink, onscreen control • 10

EasyLink, remote control • 51

EN 64

EasyLink, TV speakers • 51

energy efficient settings • 7

EPG • 14

EPG, broadcaster • 14

EPG, Internet • 15

external hard disk • 48

F

favorite channels, list • 12

G

game console, connect • 45

game settings • 28

H

HbbTV • 20

HDMI • 41

HDMI ARC • 41

hearing impaired access • 37

help, onscreen • 8

Help, version • 63

home mode • 38

home network • 53

home theater, connect • 45

I

install channels, automatic • 34

Interactive TV • 20

Internet, connect • 53

Internet, Smart TV • 18

K

Kensington lock • 5

key beep • 37

L

language, menu • 36

language, subtitles • 37

lock TV • 5

M

media server program • 15

mode, home or shop • 38

Multimedia Home Platform (MHP) • 20

multimedia, play files • 15

multimedia, play options • 16

multimedia, supported formats • 60

N

network settings • 55

network, connect • 53

network, TV name • 55

O

online forum • 8

online video, rent • 19

P

parental rating • 31

pause TV • 21

pause TV, USB hard drive • 21

PC, display resolutions • 60

Philips video camera • 49

picture format • 14

picture settings • 32

picture settings, reset • 34

Pixel Plus link • 52

placement, stand or wall • 4

placement, tips • 4

play, computer files • 15

play, USB files • 16

power specifications • 60

presets, picture and sound • 13

product support • 8

program guide • 14

program guide, broadcaster • 14

English

EN 65

program guide, Internet • 15

R

rear controls • 9

record TV, one-touch • 23

record TV, USB hard drive • 22

record, TV programs • 22

recorder, connect • 44

recordings, delete • 24

recordings, schedule • 23

recordings, watch • 24

recycle • 7

reinstall • 40

remote control • 9

rename channels • 12

rename, connected device • 50

rent, online video • 19

S

safety • 3

schedule, recordings • 23

screen care • 4

sensors • 9

settings assistant • 32

settings, audio format • 33

settings, game • 28

settings, network • 55

settings, picture • 32

settings, sound • 33

shop mode • 38

Skype • 25

Skype, block contact • 26

Skype, contacts • 26

Skype, receive call • 26

Skype, settings • 28

Skype, setup • 25

Skype, sign in • 25

Skype, video call • 26

Skype, voice call • 26

Skype, voicemails • 28

sleep timer • 30

Smart TV • 18

Smart TV, apps • 19

Smart TV, browse • 18

Smart TV, network • 53

Smart TV, start • 18

smartphone control • 10

software, check version • 39

software, digital update • 40

software, Internet update • 40

software, USB update • 39

sound settings • 33

sound settings, reset • 34

sound specifications • 60

source, select • 13

source, update • 50

standby • 11

standby LED • 9

subtitles, analog • 37

subtitles, digital • 37

subtitles, language • 37

sustainability • 7

switch TV on, off • 11

T

teletext 2.5 • 29

teletext, dual screen • 29

teletext, enlarge • 29

teletext, language • 29

teletext, search • 29

teletext, subpages • 29

teletext, Table Of Pages • 29

trademarks and copyrights • 6

TV controls • 9

EN 66

TV guide • 14

TV guide, broadcaster • 14

TV guide, Internet • 15

TV receiver, connect • 43

TV speakers, mute • 11

U

universal access, enable • 37

universal access, hearing impaired • 37

universal access, visually impaired • 38

update, source list • 50

USB, play files • 16

V

video call camera • 49

video store • 19

visually impaired access • 38

volume • 11

English

W

Wi-Fi ready, setup • 54

wireless, USB adapter • 54

Y

YouTube • 18

YPbPr, component video • 41

EN 67

All registered and unregistered trademarks are the property of their respective owners. Specifications are subject to change without notice.
Philips and the Philips’ shield emblem are registered trademarks of Koninklijke Philips Electronics N.V. and are used under license
from Koninklijke Philips Electronics N.V.
2013 © TP Vision Netherlands B.V. All rights reserved.

www.philips.com