Philips 26HW9100D, 30HW9100D User Manual

Download

Page 1

L05 User’s Manual 091105.1833

26HW9100D/30HW9100D User’s Manual

Page 2

L05 User’s Manual 091105.1833

SAFETY INFORMATION

• Disconnect mains plug when:

Ø the red light below the TV screen is flashing continuously. Ø a bright white line is displayed across the screen. Ø cleaning the TV screen. Never use abrasive cleaning agents. Use a slightly

damp chamois leather or soft cloth.

Ø there is a lightning storm. Ø the set is left unattended for a prolonged period of time.

• No open flame sources, such as lighted candles, should be placed on or near the TV.

• Do not place your TV set under direct sunlight or heat.

• Leave at least 1/4” around each side of TV set for sufficient ventilation to avoid over-

heating.

• Avoid placing set where it is likely to be exposed to rain or water (e.g. near the

window).

• No objects filled wit h liquids should be placed on top the TV in order to avoid

dripping or splashing of liquids into the set.

USEFUL TIPS

• Do not leave the television off (in standby mode) for a prolonged period of time.

Switch off set to allow the CRT to be de-gaussed (demagnetized). A de-gaussed CRT will have optimum picture quality.

• Do not re-position the television while it is switched on. Non-uniformity in screen

color may result.

• Never attempt to repair a defective TV yourself. Always consult skilled service

personnel.

Page 3

L05 User’s Manual 091105.1833

pressed while on a digital channel the television will display the digital menu instead of the

be on an analog channel to access the setup m

Before Calling Service

A list of common symptoms is presented as follows. Before you call for service, perform these simple checks. Some of these symptoms can be readily corrected. Note: Please become familiar with the commercial features as described in TV Installation / Setup, because the effects of several of these features, if they are not thoroughly understood, might appear as faulty operation.

Symptom Possible Corrective Action

TV does not respond to commands (volume, channel, power), or cannot be turned on if it is off, or cannot be turned off if it is on.

TV turns off by itself

Lack of color uniformity (color unevenness)

No power

No picture

Picture ok, no sound.

Sound ok, but poor color or no picture Check picture adjustments (brightness, contrast,

Snowy / noisy picture

Double images / “ghost” images Check antenna, cable and/or set-top box. Television does not respond to remote control.

Channel Change to digital channels is slow Channels must be programmed in the Digital OSD

Note: These televisions are shipped in commercial mode with Digital OSD turned ON. If is

Check commercial TV setup (TV installation / setup) menu settings, including power forced on, front keypad lockout, channel ring, volume minimum / maximum features.

• TV automatically turns off after approx. 5

minutes when no RF signal is present.

• Check Energy Saving Programmability setting

(see ESP) in TV installation / setup.

• Switch off the TV using the mains power

button. Wait approximately 20 minutes before switching on again.

• Ensure that the TV is not placed near speakers

or magnetic objects. Verify that the TV’s AC power cord is plugged into the mains socket. If there is still no power, disconnect plug. Wait for 60 seconds and re-insert plug. Switch on the TV again.

• Check antenna connection at rear of the TV.

• Check CABLE TUNING setting (NO / YES).

• Possible TV station problem. Try another

channel.

• Try increasing the volume.

• Check that the sound is not muted. If it is

muted, press the Mute button on the remote

control to restore sound.

• Check the MIN VOLUME/ MAX VO LUME

settings in the setup menu

color, tint).

• Check antenna, cable, and/or set-top box

connections and antenna / cable.

• Possible electrical interference from appliances

or other sources.

• Check batter ies.

• Aim remote control handset directly at remote

control sensor lens on the TV.

menu for the shortest channel change time.

commercial menu. To properly configure the television using the commercial menu, it is necessary to

enu.

Page 4

L05 User’s Manual 091105.1833

Note: The power button on the front panel

AC mains; it toggles the TV’s power mode

• Press the power button on the TV’s front

panel or on the remote control to switch on

Note 1: If the TV is in commercial mode, it

Note 2: See Mains Connection, above.

Basic Television Connection

Antenna Connection

• Connect the antenna or RF cable signal to the 75-ohm RF ‘F’ connector socket located on the TV’s rear jack panel.

Mains Connection

• Verify that the mains voltage and frequency are correct. Pl ease refer to the product labeling and documentation.

does not disconnect the television from the

between on and standby. To completely remove AC mains power, you must unpl

the AC mains plug.

Switching on the Set

the set.

might not respond to the front panel or the remote control, depending upon the TV’s mode and setup configuration. Please refer to the section TV Installation and TV Setup Menu in this documentation for more information.

Page 5

L05 User’s Manual 091105.1833

Note: Always remove the batteries from the

Use And Care of Remote Control

To load the supplied batteries into the remote control:

- Remove the battery compartment lid from the back of the remote control.

- Insert the correct type of batteries into the compartment.

- Ensure that the (+) and (-) ends of the batteries are placed in the correct positions.

- Re-attach the battery compartment li d.

remote control if it is not to be used for a long period. This can help prevent damage to the

remote from possible battery leakage.

Rear Jack Panel Connections

Page 6

L05 User’s Manual 091105.1833

1 L05HU1 1.2

CSM

REMOTE CONTROLS

The following remote co ntrols are applicable to the L05 HW-series television products. These can be used for setup and configuration purposes.

RC2888/01 RC2573GR Guest Remote Setup Remote (Optional) For the purpose of explanation, a guest remote, for the L04 series, similar to the illustration, is used. Remote control RC2573GR is a special and optional remote control specifically for configuring Institutional TV / Business Display Solutions features and SmartCard settings, and is purchased separately. Refer to the documentation for the RC2573GR for detailed information. When you press RECALL on the RC2573GR setup remote control, when it is in setup mode, information similar to the following will appear on the TV screen. This information describes the TV chassis firmware version, diagnostic codes, setup information, and other service and technical data regarding the television configuration. Line #10 indicates whether the TV is in CONSUMER or COMMERCIAL mode, and whether it is on-line with a SmartPort DCM (such as a CLON99BK SmartLoader). For more information, please refer to the service documentation for the ITV/BDS L0 5 TV chassis.

2 CODE 34 0 0 0 0 0 3 OP 2 96 225 57 126 116 0 4 AUTO AUTO MONO 5 NOT TUNED 6 7 C0 50 CL 50 BR 47 HU 19 SH 50 8 VL 4 BL 0 9 BS 50 TR 50 10 COMMERCIAL SMART PORT OFF 11 CHANNEL CVI

Page 7

L05 User’s Manual 091105.1833

the

TV off.

time with 15 minutes.

restore it.

available video sources

activate Channel

Guest Remote Control Keys

Source Select

To toggle between

CH Guide

Standby

Press to switch

DVD PAUSE

To Pause DVD

Close Caption

To activate Close Caption functionality

DVD STOP

To Stop DVD playback (if applicable)

To call up or exit the menus.

+ Vol -

To adjust the volume.

Mute

Interrupt the sound or

DVD PLAY

To Start DVD playback

DVD Rewind

To Rewind DVD

DVD FAST

FORWARD

To Fast Forward DVD playback (if applicable)

Smart Keys

To select predefined picture

and sound settings.

Sleep

Activates the sleep timer. Press repeatedly to increment the countdown

0/9 Digit keys

To select a TV channel. For a two digit program number, enter the second digit before the dash appears.

Alternate Channel

To toggle between alternating channels

+ CH – Channel

Selection

To move up or down a TV channel.

16:9 Formats

To adjust TV screen formats

Page 8

L05 User’s Manual 091105.1833

Consumer vs. Commercial Mode

The television is shipped in Commercial mode; however, at times it may be necessary to operate the set in Consumer mode. To switch between Commercial Mode and Consumer Mode the following sequence should be followed:

• With the RC2573GR Master setup remote enter 024995 and press the key.

• Use the Right cursor button to switch the Mode of the set between Consumer and

Commercial.

• With the proper mode selected, cursor down and use the Right cursor button to store

the selected mode.

• After the mode is stored, the television will power itself off. At this point disconnect

AC and perform a cold start on the television.

• The set should now be in the selected mode.

Accessing TV Setup Menus

With remote control RC2888/01 (only when SECURITY in the TV SETUP menu is set to LOW).

To activate TV Setup menu:

1. Select a channel number.

2. Key in 3 1 9 7 5 3.

3. Press .

The above sequence should be performed within 20 seconds, and the TV SETUP menu will appear.

With remote control RC2573GR (only in TV Commercial mode)

Part A: To check the television’s mode.

1. Set the remote control selectable switch to SETUP.

2. Press RECALL key and the TV Status menu will appear.

3. Check line 10 of the menu to see if the TV is in the Commercial or Consumer mode.

4. If the TV is in the Commercial mode, then proceed to Part B to activate the TV Setup menu. Otherwise, go to Part C to change the TV mode to Commercial.

Part B: To activate TV Setup menu.

1. Press the RECALL key to clear the menu.

2. Press MENU to activate the TV Setup menu.

Part C: To select Commercial mode, if the TV is in Consumer mode (or to select Consumer mode, if the TV is in Commercial mode).

Page 9

L05 User’s Manual 091105.1833

1. Press the RECALL key to clear the menu.

2. Press 0 2 4 9 9 5.

3. Press M key and the TV Mode menu appears.

4. Press + or - to select Commercial mode.

5. Highlight STORE and press the 4 key to store the change. TV will then go to standby mode.

6. Press any numeric key to switch on the TV again and follow the procedure in Part B, step 2 to activate the TV Setup menu.

Page 10

L05 User’s Manual 091105.1833

TV Setup Main Menu

LANGUAGE ENGLISH CHANNEL INSTALL > CABLE TUNING > FACTORY CH RESET > USE CHANNEL TABLE NO/YES DIGITAL OSD NO/YES ENTER DIGITAL MENU > BRIGHTNESS ||||||||||||| 0 – 100 COLOR ||||||||||||| 0 – 100 CONTRAST ||||||||||||| 0 – 100 SHARPNESS ||||||||||||| 0 – 100 TINT ||||||||||||| -50 - +50 ROTATION ||||||||||||| 0 – 63 DEFAULT FORMAT WIDESCREEN/4:3/ZOOM 14:9/ZOOM 16:9/ SUBTITLE

NOISE REDUCTION NO / YES SOUND MODE MONO / STEREO SAP NO/YES AVL NO / YES BALANCE ||||||||||||| -31 - +31 TREBLE ||||||||||||| 0 – 100 BASS ||||||||||||| 0 – 100 INCREDIBLE STEREO NO / YES ULTRA BASS YES VOLUME BAR YES MIN VOLUME ||||||||||||| 0 – 100 MAX VOLUME ||||||||||||| 0 – 100 SWITCH ON VOLUME STANDARD /||||||||||||| 0 – 100 SWITCH ON CHANNEL STANDARD / TV 1 -125 / AV 1 / AV 2 / SIDE / S-VIDEO /

POWER ON STANDARD/ FORCED / RESTORED CHANNEL DISPLAY NONE / NUMBER / LABEL / ALL KEYBOARD LOCK NO / YES ESP OFF / 1 HR / 2 HR / ... / 99 HR AUDIO/VIDEO MUTE OFF / BLUE / BLACK WELCOME MESSAGE > CHANNEL GUIDE NO / YES / POWER ON REMINDER NO / YES 3 DIGIT ENTRY NO / YES A/CH A/V SWITCH NO / YES CC OFF / CC-1 / CC-2 / CC ON MUTE SAVE CC NO / YES SOURCE MENU ITEM NO / YES HDMI AUDIO SELECTION HDMI/AV 1/AV 2/AV 3 V-CHIP MENU ITEM NO / YES SAVED V-CHIP NO / YES V-CHIP SETUP > SLEEPTIMER OFF / 15 MIN / 30 MIN / 45 MIN / 60 MIN / 90 MIN / ... / 240

SECURITY STANDARD / HIGH

Only 8 menu items will be displayed at one time.

1) To scroll through the menu, press (cursor up / down) on the remote control. A highlight indicates that the respective menu item’s setting is selected for modification.

2) To modify the setting of the selected menu item press (cursor left / right).

ZOOM/SUPER ZOOM

CVI / AV3YC / HDMI / HD CVI

MIN

3) To exit, press or RECALL on the RC2573GR setup remote control.

Page 11

L05 User’s Manual 091105.1833

TV Setup Menu and Sub-Menus

LANGUAGE (English / Espanol / Franc ais)

When you first enter the TV SETUP menu, LANGUAGE is highlighted. You can scroll to the LANGUAGE item. Select the desired language with cursor up / cursor down.

CHANNEL INSTALL (>)

The CANNEL INSTALL menu allows the user to configure the channels that can be accessed. When installing the channels, different inputs can be mapped to TV channels to allow seamless integration into the channel map. The two sections below explain how to install analog channels and AV inputs, and how to install digit al channels.

Installing Analog channels

When selected, CHANNEL INSTALL menu appears as follows. Configure the inputs and channels as described.

CHANNEL INPUT

AUTO PROGRAM CHANNEL RING LABEL VIDEO BLANK AUDIO MUTE

• CHANNEL:

o Select the channel or input you wish to configure.

• INPUT:

o Select the input source that you wish to associate with the specified

CHANNEL . This feature enables you to “map” (re-assign) a numeric channel number to a video input, rather than to its normal RF TV channel (i.e. ANTENNA). In other words, TV channel 2 could be used to select the AV 1 video input instead of RF (ANTENNA) channel 2. Special instructions for mapping digital channels are included below.

• AUTO PROGRAM:

o When AUTO PROGRAM is selected, the TV performs an automatic search

for the presence of viable RF signals at its tuner input. An AUTO PROGRAMMING ACTIVE message and a table of channel numbers will appear. If CABLE TUNING is set to NO, channels 2 through 69 will be checked. If CABLE TUNING is set to YES, channels 2 through 125 will be checked. When a viable signal is detected on a given channel, that channel is highlighted in red and is added to the channel ring. Any command from a remote control terminates the AUTO PROGRAM session. Front-panel commands do not cancel auto-programming.

• CHANNEL RING:

CHANNEL INSTALL

ANTENNA / AV 1 / AV 2 / SIDE / S-VIDEO / CVI / AV3YC /

HDMI / HD CVI / DIGITAL

TV 1– 125

SAVED

NO/YES NO/YES

Page 12

L05 User’s Manual 091105.1833

o Specify whether the current channel or input is to be SAVED to or DELETED

from the c hannel ring (i.e., list of channels available for selection by means of a standard guest remote control).

• LABEL:

o Input a maximum of 8 characters for the channel’s label. Cursor to the Right

to start the first character. Cursor left or right to navigate be tween character positions within the label field. Cursor up or down to select characters from the list:- A to Z, 0 to 9, . , ., .,/, :, =, ?, ;, <, >, @ or space. To edit, re-input the character at its position. To exit, cursor left or right to navigate o ut of the label editing field.

• VIDEO BLANK:

o Specify whether video for the current channel is to be displayed (VIDEO

BLANK = NO) or not displayed (VIDEO BLANK = YES).

• AUDIO MUTE:

o Specify whether audio for the current channel is to be audible (AUDIO

MUTE = NO) or muted (AUDIO MUTE = YES).

Installing AV Inputs

CHANNEL

CHANNEL INSTALL

CHANNEL RING LABEL VIDEO BLANK AUDIO MUTE

AV 1 / AV 2 / SIDE / S-VIDEO / CVI / AV3YC / HDMI / HD CVI

SAVED

NO/YES NO/YES

• CHANNEL:

o Select the input you wish to configur e.

• LABEL:

o Input a maximum of 8 characters for the channel’s label. Cursor to the Right

to start the first character. Cursor left or right to navigate between character positions within the label field. Cursor up or down to select characters from the list:- A to Z, 0 to 9, . , ., .,/, :, =, ?, ;, <, >, @ or space. To edit, re-input the character at its position. To exit, cursor left or right to navigate out of the label editing field.

• VIDEO BLANK:

o Specify whether video for the current channel is to be disp layed (VIDEO

BLANK = NO) or not displayed (VIDEO BLANK = YES).

• AUDIO MUTE:

o Specify whether audio for the current channel is to be audible (AUDIO

MUTE = NO) or muted (AUDIO MUTE = YES).

Page 13

L05 User’s Manual 091105.1833

Installing Digital Channels

CHANNEL

CHANNEL INSTALL

INPUT MAJOR CHANNEL MINOR CHANNEL CHANNEL RING LABEL VIDEO BLANK AUDIO MUTE

TV 1 – 125

DIGITAL

0 – 999 0 – 999

SAVED

NO/YES NO/YES

• CHANNEL:

o Select the channel or input you wish to configure.

• INPUT:

o When DIGITAL is selected two additional entries are added to the menu to

allow for mapping the digital channels.

• MAJOR CHANNEL:

o MAJOR CHANNEL refers to the either the DIGITAL RF (USE CHANNEL

TABLE = NO) channel or the channel referred to in the digital channel table (USE CHANNEL TABLE = YES).

• MINOR CHANNEL:

o MINOR CHANNEL refers to the digital sub -channel related to the MAJOR

CHANNEL specified above.

• CHANNEL RING:

o Specify whether the current channel or input is to be SAVED to or DELETED

from the channel ring (i.e., list of channels available for selection by means o f a standard guest remote control).

• LABEL:

o Input a maximum of 8 characters for the channel’s label. Cursor to the Right

to start the first character. Cursor left or right to navigate between character positions within the label field. Cursor up or down to select characters from the list:- A to Z, 0 to 9, . , ., .,/, :, =, ?, ;, <, >, @ or space. To edit, re-input the character at its position. To exit, cursor left or right to navigate out of the label editing field.

• VIDEO BLANK:

o Specify whether video for the current channel is to be displayed (VIDEO

BLANK = NO) or not displayed (VIDEO BLANK = YES).

• AUDIO MUTE:

o Specify whether audio for the current channel is to be audible (AUDIO

MUTE = NO) or muted (AUDIO MUTE = YES).

CABLE (NO / YES)

Select either standard off-air tuning (CABLE TUNING = NO) or cable offset tuning (CABLE TUNING = YES).

FACTORY CH RESET (>)

Cursor Right will reset the channels programmed in memory.

Page 14

L05 User’s Manual 091105.1833

USE CHANNEL TABLE (NO/YES)

When NO is selected the MAJOR channel in the Digital channel setup in the CHANNEL INSTALLATION menu refers to an RF channel (frequency). When YES is selected the Major channel refers to the Major channel listed in the Digital Channel Map.

DIGITAL OSD (NO/YES)

Specify whether the consumer digital version of the OSD is displayed when MENU

is pressed from a digital channel.

ENTER DIGITAL MENU (>)

Cursor RIGHT will bring up the Consumer DIGITAL Menu below:

The primary use of this menu is to program the digital channels using the Auto Program function of the digital module in the television. To program the digital channels, cursor down to Install, and Cursor Right. This will display the Install Menu. From The Install menu, select Auto Program and Cursor Right to start the Auto Programming.

Page 15

L05 User’s Manual 091105.1833

Note: The digital channels must be programmed using the Digital Menu to allow for the fastest possible channel change times.

To exit the digital menu, press the key on the setup remote twice.

BRIGHTNESS (||||||||||||| 0 – 100)