Philips 191TV4L User Manual

www.philips.com/welcome

191TV4L

English

EN Notice & important information 2

User manual 5

Troubleshooting 18

Model

www.philips.com/support

Serial

Country Telephone number

Argentina 0800 3330 856

Brazil 0800-7254101

Register your product and get support at

www.philips.com/welcome

This information is correct at the time of press. For updated information, see www.philips.com/support.

Contents

9 Pixel policy 16

1 Notice 2

2 Important 3

The most updated user manual on line 4

3 Get started and connect your
devices 5

Back connector 5
Side connector 6

4 Controls 7

Side control buttons 7
Remote control 7

5 Start to use 9

Switch your monitor on/off or to standby 9
Switch channels 9
Watch connected devices 10
Adjust monitor volume 10

6 Product information 11

Supported display resolutions 11
Tuner/Reception/Transmission 11
Remote control 11
Power 11
Supported monitor mounts 11

10 Troubleshooting 18

General monitor issues 18
TV channel issues 18
Picture issues 18
Sound issues 19
HDMI connection issues 19
Computer connection issues 19
Contact us 19

EnglishEnglish

7 TV/Channel installation 12

Using TV signal as the input source 12

8 Settings 13

Adjusting Preset Setting 13
Adjust Picture Setting 13
Adjust Audio Setting 14
Feature Setup 14

1EN

1 Notice

2012 © Koninklijke Philips Electronics N.V.
All rights reserved.

Philips and the Philips Shield Emblem are
registered trademarks of Koninklijke Philips
Electronics N.V. and are used under licence
from Koninklijke Philips Electronics N.V.

Specications are subject to change without

notice.

Warranty

• Risk of injury, damage to monitor or void
of warranty! Never attempt to repair the
monitor yourself.

• Use the monitor and accessories only as
intended by the manufacturer.

• Any operation expressly prohibited in
this manual, or any adjustments and
assembly procedures not recommended
or authorised in this manual shall void the
warranty.

• Warranty coverage begins from the day
you purchase your monitor. For two years
thereafter, your monitor will be replaced
by at least an equivalent monitor in case
of defects provided by the warranty
coverage.

Pixel characteristics

This monitor product has a high number
of color pixels. Although it has effective
pixels of 99.999% or more, black dots or
bright points of light (red, green or blue)
may appear constantly on the screen.
This is a structural property of the display
(within common industry standards) and
is not a malfunction.
Please refer to the Pixel Policy section in
this manual for details.

Copyright

VESA, FDMI and the VESA Mounting Compliant
logo are trademarks of the Video Electronics
Standards Association.
® Kensington and Micro Saver are registered
US trademarks of ACCO World Corporation
with issued registrations and pending
applications in other countries throughout the
world.

2 EN

2 Important

Read and understand all instructions before you
use your monitor. If damage is caused by failure
to follow instructions, the warranty does not
apply.

Safety

• Risk of electric shock or re!

• Never expose the monitor to rain or

water. Never place liquid containers,
such as vases, near the monitor.
If liquids are spilt on or into the
monitor, disconnect the monitor
from the power outlet immediately.
Contact Philips Consumer Care to
have the monitor checked before
use.

• Never place the monitor, remote

control or batteries near naked

ames or other heat sources,

including direct sunlight.

To prevent the spread of re, keep
candles or other ames away from

the monitor, remote control and
batteries at all times.

• Never insert objects into the

ventilation slots or other openings on
the monitor.

• When the monitor is swivelled,

ensure that no strain is exerted on
the power cord. Strain on the power
cord can loosen connections and
cause arcing.

• Risk of short circuit or re!

• Never expose the remote control or

batteries to rain, water or excessive
heat.

• Avoid force coming onto power

plugs. Loose power plugs can cause

arcing or re.

• Risk of injury or damage to the monitor!

• Two people are required to lif t and

carry a monitor that weights more
than 25 kg.

• When stand mounting the monitor,
use only the supplied stand. Secure
the stand to the monitor tightly. Place

the monitor on a at, level surface

that can support the combined
weight of the monitor and the stand.

• When wall mounting the monitor,
use only a wall mount that can
support the weight of the monitor.
Secure the wall mount to a wall that
can support the combined weight
of the monitor and wall mount.
Koninklijke Philips Electronics N.V.
bears no responsibility for improper
wall mounting that results in accident,
injury or damage.

• Risk of injury to children! Follow these
precautions to prevent the monitor
from toppling over and causing injury to
children:

• Never place the monitor on a surface

covered by a cloth or other material
that can be pulled away.

• Ensure that no part of the monitor

hangs over the edge of the sur face.

• Never place the monitor on tall

furniture (such as a bookcase)
without anchoring both the furniture
and monitor to the wall or a suitable
support.

• Educate children about the dangers

of climbing on furniture to reach the
monitor.

• Risk of overheating! Never install the
monitor in conned space. Always leave

at least 4 inches of space around the
monitor for ventilation. Ensure cur tains or
other objects never cover the ventilation
slots on the monitor.

• Risk of damage to the monitor! Before
you connect the monitor to the power
outlet, ensure that the power voltage
matches the value printed on the back of
the monitor. Never connect the monitor
to the power outlet if the voltage is
different.

English

3EN

• Risk of injury, re or power cord damage!

Never place the monitor or any objects
on the power cord.

• To easily disconnect the monitor power
cord from the power outlet, ensure that

you have full access to the power cord at
all times.

• When you disconnect the power cord,
always pull the plug, never the cable.

• Disconnect the monitor from the power
outlet and aerial before lightning storms.
During lightning storms, never touch any
part of the monitor, power cord or aerial
cable.

• Risk of hearing damage! Avoid using
earphones or headphones at high
volumes or for prolonged periods of time.

• If the monitor is transpor ted in
temperatures below 5°C, unpack the
monitor and wait until the monitor
temperature matches the room
temperature before connecting the
monitor to the power outlet.

Recycling

Your display is manufactured with high quality
materials and components which can be
recycled and reused.
To learn more about our recycling program,
please visit www.philips.com/about/
sustainability/recycling.
When you see the crossed-out wheeled bin
symbol attached to a product, it means the
product is covered by the European Directive
2002/96/EC:

Screen care

• Avoid stationary images as much as
possible. Stationary images are images
that remain on-screen for extended
periods of time. Examples include:
on-screen menus, black bars and time
displays. If you must use stationary images,
reduce screen contrast and brightness to
avoid screen damage.

• Unplug the monitor before cleaning.

• Clean the monitor and frame with a soft,

damp cloth. Never use substances such as
alcohol, chemicals or household cleaners
on the monitor.

• Risk of damage to the monitor screen!
Never touch, push, rub or strike the
screen with any object.

• To avoid deformations and color fading,
wipe off water drops as soon as possible.

4 EN

Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products. The correct
disposal of your old product helps prevent
potentially negative consequences for the
environment and human health.
Your product contains batteries covered by
the European Directive 2006/66/EC , which
cannot be disposed of with normal household
waste.
Please inform yourself about the local rules
on the separate collection of batteries. The
correct disposal of batteries helps prevent
potentially negative consequences for the
environment and human health.

The most updated user manual on line

The contents of the user manual are subject
to change. Please refer to www.philips.com/
support for the most updated user manual info

reference.

AUDIO

OUT

3 Get started and

connect your
devices

Congratulations on your purchase, and

welcome to Philips! To fully benet from the

support that Philips offers, register your product
at www.philips.com/welcome.

This section describes how to connect
various devices with different connectors and
supplements examples provided in the Quick

Start Guide.

a TV ANTENNA

Signal input from an antenna, cable or
satellite.

English

Note

• Different types of connectors may be used to

connect a device to your monitor, depending on
availability and your needs.

Back connector

5

34 2 1

b COMPONENT INPUT (Y Pb Pr)

Analogue audio and video input from
analogue or digital devices such as DVD
players or game consoles.

c AV INPUT

Audio and video input from an AV device.

5EN

d PC IN (VGA and AUDIO IN)

VGA

Audio and video input from a computer.

The connection via VGA requires an

additional audio cable.

e HDMI

Digital audio and video input from high-

denition digital devices such as Blu-ray

players.

Side connector

1

a USB

For service only.

6 EN

4 Controls

Side control buttons

Remote control

English

1

2

19

18

1

17

3

4

5

6

2

3

4

a USB:

For service only.

b POWER: Switch the monitor on

or off. The monitor is not powered
off completely unless it is physically
unplugged.

c CH +/-: Switch to the nex t or previous

channel.

d VOL +/-: Increase or decrease volume.

16

15

14

a (Standby-On)

• Switch the monitor to standby if the
monitor is on.

• Switch the monitor on if the monitor
is in standby.

b SOURCE

Select connected devices.

7

8

9

10

11

12

13

7EN

c INFO

Display or hide the information screen
about the selected channel.

d GUIDE

Switch the Electronic Program Guide On
or Off.

e (Color button)

Follow the on screen instructions.

f OPTION

Press to display a list of options.

g ▲▼◄►(Navigationbuttons)

(No functions)

Navigate through the menus.

h OK

Conrm an entry or selection.

i BACK /

• Return to the previous screen.

• Return to the last viewed channel.

j P +/-

Switch to the nex t or previous channel.

k (Mute)

Switch the sound On or Off.

l 0-9 (Numeric buttons)

Select a channel or setting.

.

m

Access the services of the current DTV
channel.

n PREV CH

• Return to the previous screen.

• Return to the last viewed channel.

o VOL +/-

Increase or decrease the volume.

p MENU

Press to open or close the on-screen
menu.

q FORMAT

Switch to different aspect ratio.

r CC

Switch the closed caption mode.

s AUDIO

Switch stereo mode.

8 EN

5 Start to use

This section helps you perform basic monitor
operations.

Tip

• Though your monitor consumes ver y little

power when in standby, energy continues to be
consumed. When not in use for an extended
period of time, disconnect the monitor power
cable from the power outlet.

English

Switch your monitor on/off or to standby

To switch on

• If the standby indicator is off, press
Power at the side of the monitor.

• If the standby indicator is red, press
(Standby-On) on the remote control.

To switch to standby

• Press (Standby-On) on the remote

control.

» The standby indicator switches to red.

To switch off

• Press Power at the side of the monitor.

» The standby indicator switches off.

Note

• If you cannot locate your remote control and

want to switch on the monitor from standby,
press POWER at the side of the monitor.

Switch channels

• Press P +/-, or enter a channel number
using the numeric buttons on the remote
control.

• Press the CH +/- button at the side of the
monitor.

9EN

Watch connected devices

TV

PC

AV

HDMI

Component

SOURCE

Note

• Switch on the connected device before selecting

it as a source on the monitor.

To select from the SOURCE button

1. Press SOURCE to display the source list.

» The source list appears.

2. Press ▲, ▼, ◄, or ► to select a device.

3. Press OK to confirm your selection.

Adjust monitor volume

To turn up or down the volume

• Press VOL +/- on the remote control.

• Press VOL +/- buttons at the side of the

monitor

To mute or restore the muted sound

• Press to mute the sound.

• Press again to restore the sound.

10 EN

6 Product

Remote control

information

Product information is subject to change
without notice. For detailed product
information, go to www.philips.com/support.

Supported display resolutions

Computer formats

• Resolution - refresh rate:

• 640 x 480 - 60Hz

• 640 x 480 - 72Hz

• 640 x 480 - 75Hz

• 720 x 400 - 70Hz

• 800 x 600 - 56Hz

• 800 x 600 - 60Hz

• 800 x 600 - 72Hz

• 800 x 600 - 75Hz

• 1024 x 768 - 60Hz

• 1024 x 768 - 70Hz

• 1024 x 768 - 75Hz

• 1280 x 720 - 60Hz

• 1280 x 1024 - 60Hz

• 1360 x 768 - 60Hz

• 1366 x 768 - 60Hz

Video formats

• Resolution - refresh rate:

• 480i - 60Hz

• 480p - 60Hz

• 720p - 60Hz

• 1080i - 60Hz

• 1080p - 24Hz, 60Hz

Tuner/Reception/Transmission

• Type: 191TV4L RC (RC2143619/01)

• Batteries: 2 x AAA

Power

• Mains power: 100-240V, 50Hz/60Hz

• Power On: 30W max.

• Standby mode: < 0.5Watt

• Off mode: < 0.5Watt

• Ambient temperature: 35 ºC for

moderate climates (Maximum ambient
temperature)

Supported monitor mounts

To mount the monitor, purchase a Philips
monitor mount or a VESA-compatible monitor
mount. To prevent damage to cables and
connectors, be sure to leave a clearance of at
least 5.5 cm from the back of the monitor.

Warning

• Follow all instructions provided with

the monitor mount. Koninklijke Philips
Electronics N.V. bears no responsibility for
improper monitor mounting that results in
accident, injury or damage.

Monitor
screen size
(inches)

18. 5 75 x 75 4 x M4

Required
pitch (mm)

Required
mounting bolts

English

• Antenna input: 75ohm coaxial (F-type)

• Digital TV: ISDB-Tb, SBTVD-T

• TV system: PAL M/N , NTSC

• Video playback: NTSC, PAL

• Tuner Bands: Hyperband, UHF, VHF

11EN

channels

channels and antenna

7 TV/Channel

channels list

channels

channels list

installation

This chapter describes the channel installation
settings.

• [Skip]: Skip the selected channel. The
selected channel will be skipped when
using the P +/- to switch the channels.

• [Block]: The selected channel will
be block. You can access the block
channel by entering the password.

• [Delete]: Delete the channel from the
channel list.

Using TV signal as the input source

channels

channels and antenna

select

backMENU

exit

1. Press MENU to display the menu.

2. Press ◄ or ► to select [channels].

3. Press OK to confirm your selection.

Channels list

You can edit a list of your preferred TV channels

so that you can nd those channels easily.

12-1 TV 1
12-2 Promo TV 2
12-3 TV 3
12-4 TV 4

1. Press MENU.

2. Press ◄ or ► to select [channels] and
press ▼ to select [channels list].

3. Press OK to confirm your selection.

» The channels list appears.

4. Follow the on screen instructions.

• [Favorite]: Add the selected channel

to the favorite channel list.

12-5 Temp TV 5
12-6 Radio 6
12-7 Temp Radio 7
12-8

settingpicture sound

backMENU exit 1/2favorite skip block delete

Channels and antenna

Select TV source signal and search new
channels.

TV signal source air
new channel scan
enable one-seg off

select

backMENU

1. Press MENU.

2. Press ◄ or ► to select [channels] and

press ▼ and ◄ or ► to select [channels
and antenna].

3. Press OK to confirm your selection.

» The channels and antenna submenu

appears.

4. Select one of the following options and
press OK.

• [TV signal source]: Select TV source

signal from air or cable.

• [Add channels]: Scan all channels

and store in the channel table
automatically.

• [New channel scan]: Add channels

which are new found.

• [Services navigation]: Shift through

the channel services using keys P+/- for
primary channels.

• [Enable one-seg]: Enable the display of

one-seg content.

add channels
services navigation off

exit

12 EN

8 Settings

ADJUST

Adjust Picture Setting

This chapter describes how to change settings
and customize functions.

Adjusting Preset Setting

picture vivid
channels list

select

backMENU

1. Press OPTION to display the submenu.

2. Press ▲, ▼, ◄, or ► to select one of the
following options and press OK.

• [Picture]: Select the preset picture

mode from [mild], [standard],

[sport], [cinema], [game], [vivid], and
[personal].

• [Sound]: Select the sound mode from

[standard], [theatre], [voice], [music],
and [personal].

• [Channel list]: Display the channel list.

• [Favorite list]: Display the favorite list.

sound personal
favorite list

exit

channels settingpicture sound

standard

cinema
vivid
mild

select

backMENU

exit

sport
game
personal
advanced setup

1. Press MENU.

2. Press ◄ or ► to select [picture] and press

▼.

3. Press ▲, ▼, ◄, or ► to select one of the
following options and press OK to enter.

• [Standard]: For standard picture

settings. Recommended for home
entertainment.

• [Cinema]: For viewing lm-based

content. Most suitable for viewing in a
theater-like environment.

• [Vivid]: For Enhances picture contrast

and sharpness.

• [Mild]: For Soft state of contrast,

brightness, color, and clarity.

• [Sport]: For viewing sports program.

• [Game]: For viewing Game.

• [Personal]: The user can set their

favorite setting.

• [Advanced setup]:

• [Color temp]: Gives three color

temperature to select, such as,
normal, cool, and warm.

• [Aspect]: Choose the display aspect.

English

Note

• Preset for all inputs can also be accessed by

pressing OPTION on the remote control and
selec t [picture] to change the modes.

13EN

Adjust Audio Setting

Feature Setup

channels settingpicture sound

standard

voice
music

select

backMENU

exit

theatre
personal
advanced setup

1. Press MENU.

2. Press ◄ or ► to select [sound] and press

▼.

3. Press ▲, ▼, ◄, or ► to select one of the
following options and press OK to enter.

• [Standard]: For standard audio

settings. Recommended for home
entertainment.

• [Voice]: Enhances treble and keep bass

in middle.

• [Music]: Enhances treble and bass.

• [Theatre]: For lm-based content to

create a theatre-like environment.

• [Personal]: Adjust sound mode as

personal favorite.

• [Advanced setup]:

• [AVL]: Enable or disable Automatic

Volume Level.

• [MTS audio]: Select from audio 1-3.

• [Digital dual]: Select from

[main+sub], [main], or [sub].

Note

• Preset for all inputs can also be accessed by

pressing OPTION on the remote control and
selec t [sound] to change the modes.

channels settingpicture sound

pc
OSD

select

backMENU

exit

other adjustments
system reset

1. Press MENU.

2. Press ◄ or ► to select [setting] and press

▼.

3. Press ▲, ▼, ◄, or ► to select one of the
following options and press OK to enter.

• [pc]:

• [Auto Adjust]: Auto sync. PC timing
to t full screen display.

For detail supported timing, please
refer PC Input Signal Reference
Char t on page 11.

• [H. Position]: Adjusts the
Horizontal positioning.

• [V. Positio n]: Adjusts the Vertical
positioning.

• [Phase]: Adjusts the Phase
frequency on VGA signal.

• [Clock]: Adjusts the Clock
frequency on VGA signal.

• [OSD]:

• [Language]: Adjust the language

setting for this TV unit. (English /
Español / Portugues).

• [Exhibition time]: Set the time for
the OSD menu display.

• [Other adjustments]:

• [Change password]: Allows

to change the parental control
password.

• [Parental control]: Set the parental
control by ratings.

• [Blue Screen]: Set the blue screen
to on or off. When there’s no signal
received, the blue screen displayed.

• [Sleep]: Set a preset time to turn off
the TV automatically.

14 EN

• [Color system]: Set the color
system from [auto], [PAL- M],
[PAL-N], or [NTSC-M].

• [HDMI / DVI switch]: Set to
[auto] for switch the input signal
automatically, or set to [HDMI] or
[DVI] for switch the signal input

manually.

• [Closed caption mode]: Set the
closed caption to [off], [on], or
[with mute].

• [Analog closed caption]: Select the
analog closed captions from CC1­CC2.

• [Digital closed caption]: Select
the digital closed captions from
Subtitle1-Subtitle8.

• [System reset]: Restore all the default
settings.

English

15EN

9 Pixel policy

Philips strives to deliver the highest quality
products. We use some of the industry's most
advanced manufacturing processes and practice
stringent quality control. However, pixel or
sub pixel defects on a flat monitor panel are
sometimes unavoidable. No manufacturer can
guarantee that all panels will be free from pixel
defects, but Philips guarantees that any monitor
with an unacceptable number of defects will be
repaired or replaced under warranty. This notice
explains the different types of pixel defects and
defines acceptable defect levels for each type.
In order to qualify for repair or replacement
under warranty, the number of pixel defects on
a monitor panel must exceed these acceptable
levels. For example, no more than 0.0004% of
the sub pixels on a monitor may be defective.
Furthermore, Philips sets even higher quality
standards for certain types or combinations
of pixel defects that are more noticeable than
others. This policy is valid worldwide.

Types of Pixel Defects

Pixel and sub pixel defects appear on the screen
in different ways. There are two categories of
pixel defects and several types of sub pixel
defects within each category.

Bright Dot Defects: bright dot defects appear
as pixels or sub pixels that are always lit or 'on'.
That is, a bright dot is a sub-pixel that stands out
on the screen when the monitor displays a dark
pattern.
These are some types of bright dot defects:

One lit red, green or blue sub pixel

Pixels and Sub pixels

A pixel, or picture element, is composed of
three sub pixels in the primary colors of red,
green and blue. Many pixels together form an
image. When all sub pixels of a pixel are lit, the
three colored sub pixels together appear as a
single white pixel. When all are dark, the three
colored sub pixels together appear as a single
black pixel. Other combinations of lit and dark
sub pixels appear as single pixels of other colors.

16 EN

Two adjacent lit sub pixels:

- Red + Blue = Purple

- Red + Green = Yellow

- Green + Blue = Cyan (Light Blue)

Three adjacent lit sub pixels (one white pixel)

Note

• A red or blue bright dot must be more

than 50 percent brighter than neighboring
dots while a green bright dot is 30 percent
brighter than neighboring dots.

Black Dot Defects: black dot defects appear as
pixels or sub pixels that are always dark or 'off'.
That is, a dark dot is a sub-pixel that stands out
on the screen when the monitor displays a light
pattern.
These are some types of black dot defects:

English

Proximity of Pixel Defects

Because pixel and sub pixels defects of the same
type that are near to one another may be more
noticeable, Philips also specifies tolerances for
the proximity of pixel defects.

Pixel Defect Tolerances

In order to qualify for repair or replacement
due to pixel defects during the warranty period,
a Philips flat monitor panel must have pixel or
sub pixel defects exceeding the tolerances listed
in the following tables.

17EN

10 Troubleshooting

This section describes commonly encountered
issues and suggested solutions.

General monitor issues

The monitor does not switch on:

• Disconnect the power cable from the
power outlet. Wait for one minute then
reconnect it.

• Check that the power cable is securely
connected.

The remote control is not working properly:

• Check that the remote control batteries
are correctly inser ted according to the
+/- orientation.

• Replace the remote control batteries if

they are at or weak.

• Clean the remote control and monitor
sensor lens.

The monitor menu is in the wrong language

• Change the monitor menu to your
preferred language.

When turning the monitor on/off/to standby,
you hear a creaking sound from the monitor
chassis:

• No action is required. The creaking sound
is normal expansion and contraction of
the monitor as it cools and warms up.
This does not impact performance.

TV channel issues

Previously installed channels do not appear in
the channel list:

• Check that the correct channel list is
selected.

No digital channels were found during the
installation:

• Check that the monitor supports
ISDB-Tb, SBTVD-T in your country. See
the listed countries on the back of the
monitor.

Picture issues

The monitor is on, but there is no picture:

• Check that the antenna is properly
connected to the monitor.

• Check that the correct device is selected
as the monitor source.

There is sound but no picture:

• Check that the picture settings are
correctly set.

There is poor monitor reception from an
antenna connection:

• Check that the antenna is properly
connected to the monitor.

• Loud speakers, unearthed audio devices,
neon lights, high buildings and other large

objects can inuence reception quality.

If possible, try to improve the reception
quality by changing the antenna direction
or moving devices away from the monitor.

• If reception on only one channel is poor,

ne tune this channel.

There is poor picture quality from connected
devices:

• Check that the devices are connected
properly.

• Check that the picture settings are
correctly set.

The monitor did not save your picture
settings:

• Check that the monitor location is set to
the home setting. This mode offers you

the exibility to change and save settings.

Thepicturedoesnottthescreen;itistoo

big or too small:

• Try a different picture format.

The picture position is incorrect:

• Picture signals from some devices may not

t the screen correctly. Check the signal

output of the device.

18 EN

Sound issues

Computer connection issues

There is a picture but no sound from the
monitor:

Note

• If no audio signal is detected, the monitor

automatically switches the audio output off —
this does not indicate malfunction.

• Check that all cables are properly
connected.

• Check that the volume is not set to 0.

• Check that the sound is not muted.

There is a picture but the sound quality is
poor:

• Check that the sound settings are
correctly set.

There is a picture but sound comes from one
speaker only:

• Verify that sound balance is set to the
center.

HDMI connection issues

There are problems with HDMI devices:

• Note that HDCP support can delay
the time taken for a monitor to display
content from an HDMI device.

• If the monitor does not recognise the
HDMI device and no picture is displayed,
try switching the source from one device
to another and back again.

• If there are intermittent sound
disruptions, check that output settings
from the HDMI device are correct.

• If an HDMI-to-DVI adaptor or HDMI
to DVI cable is used, check that an
additional audio cable is possible could be
connected to PC AUDIO IN (mini-jack
only).

The computer display on the monitor is not
stable:

• Check that a supported resolution and
refresh rate is selected on the computer.

• Set the monitor picture format to
unscaled.

Contact us

If you cannot resolve your problem, refer to
the FAQs for this monitor at ww w.philips.com/
support.
If the problem remains unresolved, contact
Philips Consumer Care in your country as
listed in this User Manual.

Warning

• Do not attempt to repair the monitor yourself.

This may cause severe injur y, irreparable
damage to your monitor or void your warranty.

Note

• Make a note of your monitor model and ser ial

number before you contact Philips. These
numbers are printed on the back of the
monitor and on the packaging.

English

19EN

Version: M4191TVE1BZT
2012 © Koninklijke Philips Electronics N.V. All rights reserved.

Specications are subject to change without notice.
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips Electronics N.V. and are used under license from

Koninklijke Philips Electronics N.V.”

www.philips.com