Philips 170T4 User Manual

Manual

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/MANUAL.HTM6/30/2004 11:36:24 AM

Safety and Troubleshooting

Safety and Troubleshooting Information

Safety Precautions and Maintenance • Installation Locations • FAQs • Troubleshooting •
Regulatory Information • Other Related Information

Safety precautions and maintenance

WARNING: Use of controls, adjustments or procedures other than those
specified in this documentation may result in exposure to shock, electrical
hazards and/or mechanical hazards.

Read and follow these instructions when connecting and using your computer monitor:

● Unplug the monitor if you are not going to use it for an extensive period of time.

● Unplug the monitor if you need to clean it with a slightly damp cloth. The screen may be

wiped with a dry cloth when the power is off. However, never use alcohol, solvents or
ammonia-based liquids.

● Consult a service technician if the monitor does not operate normally when you have

followed the instructions in this manual.

● The casing cover should be opened only by qualified service personnel.

● Keep the monitor out of direct sunlight and away from stoves or any other heat source.

● Remove any object that could fall into the vents or prevent proper cooling of the monitor’s

electronics.

● Do not block the ventilation holes on the cabinet.

● Keep the monitor dry. To avoid electric shock, do not expose it to rain or excessive moisture.

● When positioning the monitor, make sure the power plug and outlet are easily accessible.

● If turning off the monitor by detaching the power cable or DC power cord, wait for 6 seconds

before attach the power cable or DC power cord for normal operation.

● To avoid the risk of shock or permanent damage to the set, do not expose the monitor to rain

or excessive moisture.

● IMPORTANT: Always activate a screen saver program during your application. If a still

image in high contrast remains on the screen for an extended period of time, it may leave an
'after-image' or 'ghost image' on the front of the screen. This is a well-known phenomenon
that is caused by the shortcomings inherent in the LCD technology. In most cases, the after­image will disappear gradually over a period of time after the power has been switched off.
Be aware, that the after-image symptom cannot be repaired and is not covered under
warranty.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/safety.htm (1 of 2)6/30/2004 11:36:32 AM

Safety and Troubleshooting

Consult a service technician if the monitor does not operate normally when the operating
instructions given in this manual have been followed.

RETURN TO TOP OF THE PAGE

Installation Locations

● Avoid exposure to heat and extreme cold

● Do not store or use the product in locations exposed to heat, direct sunlight or extreme cold.

● Avoid moving the product between locations with large temperature differences. Choose a

site that falls within the following temperature and humidity ranges.

❍ Temperature: 5-40°C 41-104°F
❍ Humidity: 20-80% RH

● Do not subject the product to severe vibration or high impact conditions. Do not place the

product in the trunk of a car.

● Take care not to mishandle this product by either knocking or dropping it during operation or

transportation.

● Do not store or use the product in locations where there is a high level of humidity or in dusty

environments. Do not allow water or other liquids to spill on or into the product.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/safety.htm (2 of 2)6/30/2004 11:36:32 AM

About This Manual

About This Manual

About This Guide • Notational Descriptions

About This Guide

This electronic user's guide is intended for anyone who uses the Philips LCD Monitor TV. It
describes the features, setup, operation and other important information.

It includes the following sections:

● Safety and Troubleshooting Information provides tips and solutions for common problems as

well as other related information you may need.

● About This Electronic User's Manual gives an overview of information included, along with

notation icon descriptions and other documentation for your reference.

● Product Information gives an overview of the monitor's features as well as the technical

specifications for this monitor.

● Installing Your Monitor describes the initial setup process and gives an overview of how to

use the monitor.

● On-Screen Display provides information on adjusting the settings on your monitor.

● TV Control provides information on adjusting the settings for your TV function.

● Customer Care and Warranty contains a list of worldwide Philips Consumer Information

Centres along with help desk phone numbers and information on the warranty applicable to
your product.

● Download and Print Option transfers this entire manual to your hard drive for easy reference.

RETURN TO TOP OF THE PAGE

Notational Descriptions

The following subsections describe notational conventions used in this document.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/about/about.htm (1 of 2)6/30/2004 11:36:35 AM

About This Manual

Notes, Cautions and Warnings

Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic
type. These blocks contain notes, cautions or warnings. They are used as follows:

NOTE: This icon indicates important information and tips that help you make
better use of your computer system.

CAUTION: This icon indicates information that tells you how to avoid either
potential damage to hardware or loss of data.

WARNING: This icon indicates the potential for bodily harm and tells you how
to avoid the problem.

Some warnings may appear in alternate formats and may not be accompanied by an icon. In such
cases, the specific presentation of the warning is mandated by the relevant regulatory authority.

RETURN TO TOP OF THE PAGE

©2004 Koninklijke Philips Electronics N.V.

All rights reserved. Reproduction, copying, use, modification, hiring, renting, public performance, transmission and/or
broadcasting in whole or in part is prohibited without written consent of Philips Electronics N.V.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/about/about.htm (2 of 2)6/30/2004 11:36:35 AM

Product Information

Product Information

Product Features • Technical Specifications • Resolution & Preset Modes • Philips Pixel
Defect Policy • Automatic Power Saving • Physical Specification • Pin Assignment •
Product Views • Physical Function

Product Features

170T4

● 17-inch WXGA LCD all-in-one Monitor TV with excellent display performance

● Multiple video input allowing display of PC, TV, VCD, DVD and CamCorder

● MultiSystem TV tuner-PAL/NTSC (available in most of the Asia Pacific area)

RETURN TO TOP OF THE PAGE

Technical Specifications*

LCD PANEL

• Type TFT LCD

• Screen size 17 inch

• Pixel Pitch 0.297 x 0.297mm

• LCD Panel type

1280 x 768 pixels
R.G.B. vertical stripe
Anti-glare polarizer

• Effective viewing area (H) 369.6 x (V) 221.76 mm

• Display Colors 8 bits interface (16.7M colors)

PC SCANNING

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/product/product.htm (1 of 7)6/30/2004 11:36:39 AM

Product Information

• Vertical refresh rate
56Hz-76Hz

• Horizontal frequency 30kHz-63kHz

PC VIDEO

• Video dot rate 103 MHz

• Input impedance

- Video
75 ohm

- Sync
2K ohm

• Input signal levels 0.7 Vpp

• Sync input signal

Separate sync

• Sync polarities Positive and negative

• Input Frequency

WXGA Hsync 48- 60 kHz, Vsync 60 - 75 Hz (N.I.)
XGA Hsync 48- 60 kHz, Vsync 60 - 75 Hz (N.I.)
SVGA Hsync 37- 47 kHz, Vsync 60 - 75 Hz (N.I.)
VGA Hsync 31- 38 kHz, Vsync 60 - 75 Hz (N.I.)

• Video interface D-sub, S-Video, TV-RF and composite video

AUDIO

• Input level for PC/SVHS 500 mV nominal

• Headphone out signal level 4mW max.

• Loudspeaker

5W Stereo Audio (2.5W/channel RMS x2, 200 Hz~10 kHz,
8 ohm, 10% THD)

OPTICAL CHARACTERISTICS

• Contrast ratio 600:1 (typ.)

• Brightness

450 cd/m

2

(typ.)

• Peak contrast angle 6 o'clock

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/product/product.htm (2 of 7)6/30/2004 11:36:39 AM

Product Information

• White Chromaticity

x: 0.283 y: 0.297 (at 9300° K)
x: 0.313 y: 0.329 (at 6500° K)
x: 0.313 y: 0.329 (sRGB)

• Viewing Angle (C/R >5)

Upper >85° (typ.)

Lower >85° (typ.)

Left >85° (typ.)

Right >85° (typ.)

• Response time <=25ms (typ.)

* This data is subject to change without notice.

RETURN TO TOP OF THE PAGE

Resolution & Preset Modes

• Maximum

1280 x 768 at 75Hz

• Recommended 1280 x 768 at 60Hz

14 user definable modes

9 factory preset modes:

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/product/product.htm (3 of 7)6/30/2004 11:36:39 AM

Product Information

Resolution Mode H. freq (kHz) V. freq (Hz)

PC

640*480 VGA VESA 60 31.469 59.940
640*480 VGA VESA 75 37.500 75.000
720*400 IBM VGA 3H 31.468 70.087
800*600 SVGA VESA 60 37.879 60.317

800*600 SVGA VESA 75 46.875 75.000
1024*768 XGA VESA 60 48.363 60.004
1024*768 XGA VESA 75 60.023 75.029
1280*768 WXGA VESA 60 47.700 60.000
1280*768 WXGA VESA 75 60.100 75.000

Video

Video 60Hz 15.734 59.940
Video 50Hz 15.625 50.000

RETURN TO TOP OF THE PAGE

Automatic Power Saving

If you have VESA DPMS compliance display card or software installed in your PC, the monitor can
automatically reduce its power consumption when not in use. If an input from a keyboard, mouse
or other input device is detected, the monitor will then 'wake up' automatically. The following table
shows the power consumption and signaling of this automatic power saving feature:

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/product/product.htm (4 of 7)6/30/2004 11:36:39 AM

Product Information

Power Management Definition

VESA Mode Video H-sync V-sync Power Used LED color

ON Active Yes Yes 55W (typ.) Green

OFF Blanked No No

110VAC < 1W
230VAC < 2W

Amber

This monitor is ENERGY STAR® compliant. As an ENERGY STAR® Partner, PHILIPS has
determined that this product meets the

ENERGY STAR

®

guidelines for energy efficiency.

RETURN TO TOP OF THE PAGE

Physical Specifications

• Dimension (WxHxD)

517 x 364 x 199 mm (incl. Pedestal)

• Weight 5.4 kg

• Tilt (Forward / Backward) - 5° / 20°

• Power supply 100 — 240 VAC, 50/60 Hz

• Power consumption 55 W (typ.)

• Temperature (operating) 5° C to 40° C

• Relative humidity 20% to 80%

• System MTBF

50K hours (excluding CCFL 40K hours)

* This data is subject to change without notice.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/product/product.htm (5 of 7)6/30/2004 11:36:39 AM

Product Information

Pin Assignment

The 15-pin D-sub connector (male) of the signal cable:

Pin

No.

Assignment

Pin

No.

Assignment

1

Red video input

9

DDC +5V

2

Green video input

10

Logic ground

3

Blue video input

11

Ground

4

Ground

12

Serial data line (SDA)

5

Ground

13

H. Sync

6

Red video ground

14

V. Sync

7

Green video ground

15

Data clock line (SCL)

8

Blue video ground

RETURN TO TOP OF THE PAGE

Product Views

Follow the links to see various views of the monitor and its components.

Front View Product Description

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/product/product.htm (6 of 7)6/30/2004 11:36:39 AM

Product Information

RETURN TO TOP OF THE PAGE

Physical Function

Tilt

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/product/product.htm (7 of 7)6/30/2004 11:36:39 AM

Installing your LCD Monitor/TV

Installing your LCD Monitor/TV

Front View Product Description • Connecting to Your PC, TV antenna, DVD/VCR etc. • VESA Mounting
and Easy Wall Mounting • Installing the Optional TV/AV Module • Getting Started • Optimising
Performance

Front View Product Description

1

SOURCE

TV/Video source selection

2

Increase or decrease the channel number
or
up or down the highlighted function in OSD

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/install.htm (1 of 3)6/30/2004 11:36:42 AM

Installing your LCD Monitor/TV

3

MENU

Open the OSD and select the highlighted function

4

VOL

Increase or decrease the level of audio volume
or
move up or down the highlighted function in OSD

5

Power indicator

6

Power switch On/Off

7

Receiver for 'remote control'

RETURN TO TOP OF THE PAGE

Rear View

1 DC in

DC power in

2 VGA

D-Sub input

3 PC - Audio in For connect to PC Audio output

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/install.htm (2 of 3)6/30/2004 11:36:42 AM

Installing your LCD Monitor/TV

RETURN TO TOP OF THE PAGE

Optimizing Performance

● For best performance, ensure that your display settings are set at 1280x768@60Hz (for 17").

Note: You can check the current display settings by pressing the 'MENU'

button once.

● You can also install the Flat Panel Adjust (FP Adjust) program, a program for getting the best performance

out of your monitor. This is included on this CD. Step-by-step instructions are provided to guide you through
the installation process. Click on the link to find out more about this program.

More about FP_setup03.exe

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/install.htm (3 of 3)6/30/2004 11:36:42 AM

On-Screen Display

On-Screen Display

Description of the On-Screen Display • The OSD Guide

Description of the On Screen Display

What is the On-Screen Display?

This is a feature offered by all Philips LCD monitors/TVs. It allows an end user to adjust screen
performance of monitors directly through an on-screen instruction window. The user interface
provides user-friendliness and ease-of-use when operating the monitor.

Basic and simple instruction on the control keys

When you press the

button on the front control of your monitor, the On-Screen Display

(OSD) Main Controls window will pop up and you can then start making adjustments to the various
monitor features. Use the

or the keys to make your adjustments.

RETURN TO TOP OF THE PAGE

The OSD Guide

Below is an overall view of the structure of the On-Screen Display. You can use this as a reference
when you want to work your way around the different adjustments later on.

There are three versions of OSD by region:

● Europe

● Asia Pacific and China excluding Korea, Taiwan and Philippines

● Americas and Korea, Taiwan and Philippines

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/osddesc.htm (1 of 14)6/30/2004 11:36:48 AM

On-Screen Display

Europe OSD Guide

PC Mode

INPUT SELECT

Select video source for main display:

PC

● PC VGA input

TV

● Antenna or cable TV input

AV

● CVBS Composite Video input

S-VIDEO

● S-video input

HD-YPbPr

● Progressive video input & YPbPr component

video input

LANGUAGE

Set language for OSD

ENGLISH
DEUTSCH

ITALIANO

ADJUST POSITION

Adjust positions to get optimum display location on the
screen

HORIZONTAL
VERTICAL

VIDEO MODE

FULL SCREEN

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/osddesc.htm (2 of 14)6/30/2004 11:36:48 AM

On-Screen Display

ASPECT RATIO
4:3

BRIGHTNESS & CONTRAST

Adjust brightness and contrast to obtain optimum
display

BRIGHTNESS
CONTRAST

VIDEO NOISE

Adjust phase and clock to obtain stable and clear
display

PHASE
CLOCK

ADJUST COLOR

Set color temperature to suit personal preference

ORIGINAL
PANEL COLOR

9300K FOR CAD/
CAM

6500K FOR
IMAGE
MANAGEMENT

SRGB

USER PRESET

RED
GREEN
BLUE

RESET TO FACTORY SETTINGS

Reset the setting to default values

NO
YES

AUTO

Automatic adjustment of the display parameters to
give optimum display

EXIT

Exit from this menu

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/osddesc.htm (3 of 14)6/30/2004 11:36:48 AM

On-Screen Display

RETURN TO TOP OF THE PAGE

TV/Video/HD Mode

INPUT SELECT

Select video source for main display:

PC

● PC VGA input

TV

● Antenna or cable TV input

AV

● CVBS Composite Video input

S-VIDEO

● S-video input

HD-YPbPr

● Progressive video input & YPbPr component

video input

PICTURE

Adjust picture characteristics to suit personal preference

BRIGHTNESS
CONTRAST
COLOR
SHARPNESS

COLOR TEMP

● Normal

● Cool

● Warm

EXIT

SOUND

Adjust audio characteristics to suit personal preference

TREBLE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/osddesc.htm (4 of 14)6/30/2004 11:36:48 AM

On-Screen Display

BASS
BALANCE
SURROUND (ON/

OFF)
EXIT

LANGUAGE

Set language for OSD

ENGLISH
DEUTSCH

ITALIANO

INSTALL

Install a TV program list (only available in "TV mode")

SYSTEM

Specify the TV system at the user location:

● WEST EUR (PAL B/G)

● FRANCE

AUTO STORE

Scan and store the TV programs at the user location
automatically.

MANUAL STORE

● Search

● Prog. No

● Fine tune

● Store

● Exit

Fine tune and store the TV programmes at the user
location manually

CHANNEL SKIP

Set the skipped programme when accessing
programmes using the

keys.

CHANNEL SWAP
EXIT

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/osddesc.htm (5 of 14)6/30/2004 11:36:48 AM

On-Screen Display

VIDEO MODE

STANDARD
4:3
FULL SCREEN
NONLINEAR

SCALING

EXIT

Exit from this menu

RETURN TO TOP OF THE PAGE

Asia Pacific and China OSD Guide (excluding Korean, Taiwan and Philippines)

PC Mode

INPUT SELECT

Select video source for main display:

PC

● PC VGA input

TV

● Antenna or cable TV input

AV

● CVBS Composite Video input

S-VIDEO

● S-video input

HD-YPbPr

● Progressive video input & YPbPr component

video input

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/osddesc.htm (6 of 14)6/30/2004 11:36:48 AM

On-Screen Display

LANGUAGE

Set language of OSD

ENGLISH

ADJUST POSITION

Adjust positions to obtain optimum display location on
the screen

HORIZONTAL
VERTICAL

VIDEO MODE

FULL SCREEN
ASPECT RATIO

4:3

BRIGHTNESS & CONTRAST

Adjust brightness and contrast to obtain optimum
display

BRIGHTNESS
CONTRAST

VIDEO NOISE

Adjust phase and clock to obtain stable and clear
display

PHASE
CLOCK

ADJUST COLOR

Set color temperature to suit personal preference

ORIGINAL
PANEL COLOR

9300K FOR CAD/
CAM

6500K FOR
IMAGE
MANAGEMENT

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/osddesc.htm (7 of 14)6/30/2004 11:36:48 AM

On-Screen Display

sRGB

USER PRESET

RED
GREEN
BLUE

RESET TO FACTORY SETTINGS

Reset the setting to default values

NO
YES

AUTO

Automatic adjustment of the display parameters to
give optimum display

EXIT

Exit from this menu

RETURN TO TOP OF THE PAGE

TV/Video/HD Mode

INPUT SELECT

Select video source for main display:

PC

● PC VGA input

TV

● Antenna or cable TV input

AV

● CVBS Composite Video input

S-VIDEO

● S-video input

HD-YPbPr

● Progressive video input & YPbPr component

video input

PICTURE

Adjust picture characteristics to suit personal preference

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/osddesc.htm (8 of 14)6/30/2004 11:36:48 AM

On-Screen Display

BRIGHTNESS
CONTRAST
COLOR
SHARPNESS
TINT

COLOR TEMP

● Normal

● Cool

● Warm

EXIT

SOUND

Adjust audio characteristics to suit personal preference

TREBLE
BASS
BALANCE
SURROUND (ON/

OFF)
EXIT

LANGUAGE

Set language for OSD

ENGLISH

INSTALL

Install a TV program list (only available in "TV mode")

AUTO STORE

Scan and store the TV programs at the user location
automatically

MANUAL STORE

Fine tune and store the TV programs at the user
location manually

CHANNEL SKIP

Set the skipped programme when accessing
programmes using the

keys.

CHANNEL SWAP

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/osddesc.htm (9 of 14)6/30/2004 11:36:48 AM

On-Screen Display

EXIT

VIDEO MODE

STANDARD
4:3
FULL SCREEN
NONLINEAR

SCALING

EXIT

Exit from this menu

RETURN TO TOP OF THE PAGE

Americas OSD Guide

PC Mode

INPUT SELECT

Select video source for main display:

PC

● PC VGA input

TV

● Antenna or cable TV input

AV

● CVBS composite video input

S-VIDEO

● S-video input

LANGUAGE

Set language for OSD

ENGLISH

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/osddesc.htm (10 of 14)6/30/2004 11:36:48 AM

On-Screen Display

ADJUST POSITION

Adjust positions to obtain optimum display location on
the screen

HORIZONTAL
VERTICAL

VIDEO MODE

FULL SCREEN
ASPECT RATIO

4:3

BRIGHTNESS & CONTRAST

Adjust brightness and contrast to obtain optimum
display

BRIGHTNESS
CONTRAST

VIDEO NOISE

Adjust phase and clock to obtain stable and clear
display

PHASE
CLOCK

ADJUST COLOR

Set color temperature to suit personal preference

ORIGINAL
PANEL COLOR

9300K FOR CAD/
CAM

6500K FOR
IMAGE
MANAGEMENT

sRGB

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/osddesc.htm (11 of 14)6/30/2004 11:36:48 AM

On-Screen Display

USER PRESET

RED
GREEN
BLUE

RESET TO FACTORY SETTINGS

Reset the setting to default values

NO
YES

AUTO

Automatic adjustment of the display parameters to
give optimum display

EXIT

Exit from this menu

RETURN TO TOP OF THE PAGE

TV/Video Mode

INPUT SELECT

Select video source for main display:

PC

● PC VGA input

TV

● Antenna or cable TV input

AV

● CVBS composite video input

S-VIDEO

● S-video input

PICTURE

Adjust picture characteristics to suit personal preference

BRIGHTNESS
CONTRAST
COLOR

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/osddesc.htm (12 of 14)6/30/2004 11:36:48 AM

On-Screen Display

SHARPNESS
TINT

COLOR TEMP

● Normal

● Cool

● Warm

EXIT

SOUND

Adjust audio characteristics to suit personal preference

TREBLE
BASS
BALANCE
SURROUND (ON/

OFF)
EXIT

LANGUAGE

Set language for OSD

ENGLISH

FEATURES

Activate special control features:

PARENTAL
CONTROLS

Set the password (0711) and block specific
programmes that are not suitable for children. It is
compliant with V-chip standard in the US. (

Detail

operation)

CLOSED
CAPTION

Turn on/off and select a closed caption mode

INSTALL

Install a TV program list (only available in "TV mode")

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/osddesc.htm (13 of 14)6/30/2004 11:36:48 AM

On-Screen Display

TUNER MODE

Set the tuner mode:

● auto

● antenna

● cable

AUTO STORE

Scan and store the TV programs at the user location
automatically

FINE TUNE

Fine tune and store the TV programs at the user
location manually

CHANNEL EDIT

Set the skipped channel when accessing channel by

keys

EXIT

VIDEO MODE

STANDARD
4:3
FULL SCREEN
NONLINEAR

SCALING

EXIT

Exit from this menu

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/osddesc.htm (14 of 14)6/30/2004 11:36:48 AM

TV Control

TV Control

Using Your Remote Control

Using Other Menu:

● Europe area

● Asia Pacific area and China excluding Korea, Taiwan and Philippines

● Americas

Using Your Remote Control

For European countries
For countries outside Europe

For European countries

Remote Control Diagram

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_control.htm (1 of 6)6/30/2004 11:36:52 AM

TV Control

1 Standby

To set the TV temporarily to standby mode. To switch
on the TV set, press Programme button (CH -, +), any
digit between 0 and 9 or AV source button
(The amber light indicates when set is in standby mode)

2 Numerical keys

● For direct access to programmes

For a 2-digit programme number, the 2nd digit
must be entered before the dash disappears.

● In PC/Video 'STANDBY' mode, press any of

number keys to return to 'ON' in TV mode.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_control.htm (2 of 6)6/30/2004 11:36:52 AM

TV Control

3 Menu

● To turn on or off the OSD (On-Screen Display)

● To return to last item in OSD & clear menu from

screen

4 Volume

● To adjust the sound level.

● To access the sub-menus and adjust the settings.

5 Previous programme

To access the last programme viewed.

6 SOURCE

● To select PC, TV, AV, S-Video and HD mode.

● In PC 'standby' mode, press SOURCE to switch

to TV mode.

7 Mute

● To disable sound.

● To restore sound, press button again.

8 Audio Mode

● To switch from STEREO to MONO or to choose

between Dual I and Dual II for bilingual
transmissions.

● For TV sets fitted with NICAM reception,

depending on the transmission, you can switch
from NICAM STEREO to MONO or choose
between NICAM DUAL I, NICAM DUAL II and
MONO.

9

Selecting TV
programmes

● To move up or down a programme.

● To move the cursor up/down to scroll through a

list of options.

● In PC/Video 'Standby' mode, press CH+/- to

return to 'on' in TV mode.

10 OSD

To show OSD status.

11 Sleep timer

To select the period of time after which the set will
switch automatically to standby mode (up to 240
minutes)

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_control.htm (3 of 6)6/30/2004 11:36:52 AM

TV Control

12 Screen mode

To switch between Standard Mode, 4:3 Mode, Full
Screen Mode and Nonlinear Scaling Mode video format
for optimum viewing ratio.

RETURN TO TOP OF THE PAGE

For countries outside Europe

Remote Control Diagram

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_control.htm (4 of 6)6/30/2004 11:36:52 AM

TV Control

1 Standby

To set the TV temporarily to standby mode. To switch
on the TV set, press Standby button, Programme
button (CH -, +), any digit between 0 and 9 or AV
source button.
(The amber light indicates when set is in standby mode)

2 Numerical keys

● For direct access to programmes

For a 2-digit programme number, the 2nd digit
must be entered before the dash disappears.

● In PC/Video 'STANDBY' mode, press any of

number keys to return to 'ON' in TV mode.

3 Menu

● To turn on or off the OSD (On-Screen Display)

● To return to last item in OSD & clear menu from

screen

4 Volume

● To adjust the sound level.

● To access the sub-menus and adjust the settings.

5 Previous programme

To access the last programme viewed.

6 SOURCE

● To select PC, TV, AV and S-Video mode.

● In PC 'standby' mode, press SOURCE to switch

to TV mode.

7 Mute

● To disable sound.

● To restore sound, press button again.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_control.htm (5 of 6)6/30/2004 11:36:52 AM

TV Control

8 Audio Mode

● To switch from STEREO to MONO or to choose

between Dual I and Dual II for bilingual
transmissions.

● For TV sets fitted with NICAM reception,

depending on the transmission, you can switch
from NICAM STEREO to MONO or choose
between NICAM DUAL I, NICAM DUAL II and
MONO.

9

Selecting TV
programmes

● To move up or down a programme.

● To move the cursor up/down to scroll through a

list of options.

● In PC/Video 'Standby' mode, press CH+/- to

return to 'on' in TV mode.

10 OSD

To show OSD status.

11 Sleep timer

To select the period of time after which the set will
switch automatically to standby mode (up to 240
minutes)

12 Screen mode

To switch between Standard Mode, 4:3 Mode, Full
Screen Mode and Nonlinear Scaling Mode video format
for optimum viewing ratio.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_control.htm (6 of 6)6/30/2004 11:36:52 AM

Customer Care and Warranty

Customer Care & Warranty

PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR
WARRANTY COVERAGE

WESTERN EUROPE:

Austria • Belgium • Cyprus • Denmark • France • Germany • Greece •
Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden •
Switzerland • Spain • United Kingdom

EASTERN EUROPE: Czech Republic • Hungary • Poland • Russia • Slovakia • Slovenia •

Turkey

LATIN AMERICA: Antilles • Argentina • Brasil • Chile • Colombia • Mexico • Paraguay •

Peru • Uruguay • Venezuela

NORTH AMERICA: Canada • USA

PACIFIC: Australia • New Zealand

ASIA: Bangladesh • China • Hong Kong • India • Indonesia • Japan • Korea • Malaysia •

Pakistan • Philippines • Singapore • Taiwan • Thailand

AFRICA: Morocco • South Africa

MIDDLE EAST: Dubai • Egypt

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/warranty/warranty.htm6/30/2004 11:36:55 AM

Download and Print

Download and Print

Installing your LCD monitor driver • Download and Printing Instructions • Installing FPadjust
Program

Installing Your LCD monitor driver

System requirements:

● PC running Windows® 95, Windows® 98, Windows® 2000 , Windows® Me, Windows® XP

or later

● Find your driver ".inf/.icm/.cat" at : /PC/drivers/

Read the "Driver_install02.txt" file before installing.

This page provides an option to read the manual in .pdf format. PDF files can be downloaded into
your hard disk, then viewed and printed with Acrobat Reader or through your browser.

If you do not have Adobe¨ Acrobat Reader installed, click on the link to install the application.

Adobe® Acrobat Reader for PC / Adobe® Acrobat Reader for Mac.

Download instructions:

To download the file:

1. Click-and-hold your mouse over the icon below. (Win95/98/2000/Me/XP users right-click)

Download

170T4.pdf

2. From the menu that appears, choose 'Save Link As...', 'Save Target As...' or 'Download Link to
Disk'.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/download/download.htm (1 of 3)6/30/2004 11:36:58 AM

Download and Print

3. Choose where you would like to save the file; click 'Save' (if prompted to save as either 'text' or
'source', choose 'source').

Printing instructions:

To print the manual:

1. With the manual file open, follow your printer's instructions and print the pages you need.

RETURN TO TOP OF THE PAGE

Installing FPadjust Program

The FP Adjust program generates alignment patterns which will help you adjust monitor settings
such as CONTRAST, BRIGHTNESS, HORIZONTAL & VERTICAL POSITION, PHASE and CLOCK.

System requirements:

● PC running Windows® 95, Windows® 98, Windows® 2000, Windows® Me, Windows® XP

or later

To install FPadjust Program:

● Click on the link or icon to install FPadjustment Program.

or

● Click-and-hold your mouse over the icon. (Win95/98/2000/Me/XP users right-click)

Download

FP_setup03.exe

● From the menu that appears, choose 'Save Link As...', 'Save Target As...' or 'Download Link

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/download/download.htm (2 of 3)6/30/2004 11:36:58 AM

Download and Print

to Disk'.

● Choose where you would like to save the file; click 'Save' (if prompted to save as either 'text'

or 'source', choose 'source').

● Exit your browser and install the FPadjust Program.

Read the "FP_Readme03.txt" file before installing.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/download/download.htm (3 of 3)6/30/2004 11:36:58 AM

FAQs (Frequently Asked Questions)

FAQs (Frequently Asked Questions)

Safety and Troubleshooting • General FAQs • Screen Adjustments • Compatibility with
Other Peripherals • LCD Panel Technology • Ergonomics, Ecology and Safety Standards •
Troubleshooting • Regulatory Information • Other Related Information

General FAQs

Q:

When I install my monitor what should I do if the screen shows 'Cannot display this video

mode'?

A: Recommended video mode for Philips 17" Wide WXGA: 1280x768 @60Hz.

1. Unplug all cables, then connect your PC to the monitor you used previously, which displayed

correctly.

2. In the Windows® Start Menu, select Settings/Control Panel. In the Control Panel Window,

select the Display icon. Inside the Display Control Panel, select the 'Settings' tab. Under the
settings tab, in a box labelled 'desktop area', move the slidebar to 1280x768 pixels (17"
Wide WXGA).

3. Open 'Advanced Properties' and set the Refresh Rate to 60Hz, then click OK.

4. Restart your computer and repeat steps 2 and 3 to verify that your PC is set at

1280x768@60Hz (17" Wide WXGA).

5. Shut down your computer, disconnect your old monitor and reconnect your Philips LCD

monitor.

6. Turn on your monitor and then turn on your PC.

Q: What does 'refresh rate' mean in connection with an LCD monitor?

A: The refresh rate is of much less relevance for LCD monitors. LCD monitors display a

stable, flicker-free image at 60Hz. There is no visible difference between 75Hz and 60Hz.

Q: What are the .inf and .icm files on the set-up disk & CD-ROM? How do I install the drivers

(.inf and .icm)?

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/saf_faq.htm (1 of 9)6/30/2004 11:37:11 AM

FAQs (Frequently Asked Questions)

A: These are the driver files for your monitor. Follow the instructions in your user manual to

install the drivers. The computer may ask you for monitor drivers (.inf and .icm files) or a
driver disk when you first install your monitor. Follow the instructions to insert the driver
disk (either floppy or CD-ROM) included in this package. Monitor drivers (.inf and .icm files)
will be installed automatically.

Q: How do I adjust the resolution?

A: Your video card/graphic driver and monitor together determine the available resolutions.

You can select the desired resolution under Windows® 95/98 Me & 2000/XP with the 'Display
properties/Settings' control panel.

Q: What if I get lost when I am making monitor adjustments?

A: Simply press the OSD button, then select 'Reset' to recall all of the original factory

settings.

Q: My Monitor has no power (Power LED does not light up). What should I do?

A: Make sure the power cord is connected to the Monitor.

Q: Will the product accept an Interlace signal?

A: No. If an Interlace signal is used, the screen displays both odd and even horizontal

scanning lines at the same time, thus distorting the picture.

Q: What does the Refresh Rate mean for LCD?

A: Unlike CRT display technology, in which the speed of the electron beam is swept from

the top to the bottom of the screen determines flicker, an active matrix display uses an
active element (TFT) to control each individual pixel and the refresh rate is therefore not
really applicable to LCD technology.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/saf_faq.htm (2 of 9)6/30/2004 11:37:11 AM

FAQs (Frequently Asked Questions)

Q: Will the LCD screen be resistant to scratches?

A: A protective coating is applied to the surface of the LCD, which is durable to a certain

extent (approximately up to the hardness of a 2H pencil). In general, it is recommended that
the panel surface is not subject to any excessive shocks or scratches. An optional
protective cover with greater scratch resistance is also available.

Q: How should I clean the LCD surface?

A:

For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use isopropyl

alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone, hexane, etc.

Q: Can the Philips LCD Monitor be mounted on the wall or used as a touch panel?

A: Yes. Philips LCD monitors have this optional feature. The standard VESA mount holes on

the back cover allows the user to mount the Philips monitor on any VESA standard ARM or
accessories. Touch panels are being developed for future applications. Check with your
Philips sales representative for more information.

RETURN TO TOP OF THE PAGE

Screen Adjustments

Q: What is the FPadjust program on the setup disk and CD-ROM?

A: The FPadjust program generates alignment patterns that help you adjust monitor settings

such as Contrast, Brightness, Horizontal Position, Vertical Position, Phase and Clock for
optimal performance.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/saf_faq.htm (3 of 9)6/30/2004 11:37:11 AM

FAQs (Frequently Asked Questions)

Q: When I install my monitor, how do I get the best performance from the monitor?

A:

1.

For best performance, make sure your display settings are set at 1280x768@60Hz for 17"
Wide WXGA. Note: You can check the current display settings by pressing the OSD OK
button once.
The current display mode is shown in the product information in the OSD main controls.

2. To install the Flat Panel Adjust (FPadjust) program located on the monitor setup CD-ROM,

open the CD-ROM and double click the FP_setup03.exe icon. This will install FP Adjust
automatically and place a shortcut on your desktop.

3. Run FPadjust by double clicking the shortcut. Follow the instructions step by step to optimise

image performance with your system's video controller.

Q: How do LCDs compare with CRTs in terms of radiation?

A: Because LCDs do not use an electron gun, they do not generate the same amount of

radiation at the screen surface.

RETURN TO TOP OF THE PAGE

Compatibility with other Peripherals

Q:

Can I connect my LCD monitor to any PC, workstation or Mac?

A: Yes. All Philips LCD monitors are fully compatible with standard PCs, Macs and

workstations. You may need a cable adapter to connect the monitor to your Mac system.
Please contact your dealer/retailer for more information.

Q: Are Philips LCD monitors Plug-and-Play?

A: Yes, the monitors are Plug-and-Play compatible with Windows® 95, 98, 2000, Me, XP and

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/saf_faq.htm (4 of 9)6/30/2004 11:37:11 AM

FAQs (Frequently Asked Questions)

the PC98/99 platforms.

Q: What are S-VIDEO Signals?

A: These are 2 separate Y/C video signals from the S-VIDEO and Hi-8 recording standards.

The luminance signals Y (black and white) and chrominance signals C (colour) are recorded
separately on the tape. This provides a better picture quality than is achieved with standard
video (VHS and 8 mm) where the Y/C signals are combined to provide only one video signal.

RETURN TO TOP OF THE PAGE

LCD Panel Technology

Q:

What is a Liquid Crystal Display?

A: A Liquid Crystal Display (LCD) is an optical device that is commonly used to display

ASCII characters and images on digital items such as watches, calculators, portable game
consoles, etc. LCD is the technology used for displays in notebooks and other small
computers. Like light-emitting diode and gas-plasma technologies, LCD allows displays to
be much thinner than cathode ray tube (CRT) technology. LCD consumes much less power
than LED and gas-displays because it works on the principle of blocking light rather than
emitting it.

Q: How are LCDs made?

A: LCDs are created from two glass plates separated from each other at a distance of a few

microns. The plates are filled with liquid crystal and then sealed together. The top plate is
colored with an RGB pattern to make the color filter. Polarizers are then glued to both plates.
This combination is sometimes called 'glass' or 'cell.' The LCD cell is assembled into a
'module' by adding the backlight, driver electronics and frame.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/saf_faq.htm (5 of 9)6/30/2004 11:37:11 AM

FAQs (Frequently Asked Questions)

Q: What is polarization ?

A: Polarization is basically directing light to shine in one direction. Light is electromagnetic

waves. Electric and magnetic fields oscillate in a direction perpendicular to the propagation
of the light beam. The direction of these fields is called the 'polarization direction'. Normal or
non-polarized light has fields in several directions; polarized light has a field in only one
direction.

Q: What differentiates passive matrix LCDs from active matrix LCDs?

A: An LCD is made with either a passive matrix or an active matrix display grid. An active

matrix has a transistor located at each pixel intersection, requiring less current to control
the luminance of a pixel. For this reason, the current in an active matrix display can be
switched on and off more frequently, improving the screen refresh time (your mouse pointer
will appear to move more smoothly across the screen, for example). The passive matrix LCD
has a grid of conductors with pixels located at each intersection in the grid.

Q: How does a TFT LCD Panel work?

A: On each column and row of the TFT LCD panel, a data source drive and a gate drive are

attached, respectively. The TFT drain of each cell is connected to the electrode. The
molecular arrangement of liquid crystal elements differ acceding to whether it is impressed
with voltage or not. It varies the direction of polarized light and the amount of light by letting
it through different arrays of liquid crystal elements. When two polarized filters are arranged
vertically on a polarized light pole, the light that passes through the upper polarized panel is
turned 90 degrees along with the spiral structure of the liquid crystal molecules and goes
through the polarized filter at the bottom. When impressed with voltage, liquid crystal
molecules are arranged vertically from the original spiral structure and the direction of the
light is not turned through 90 degrees. In this case, light that comes through the top
polarized panel may not go through the polarized panel at the bottom.

Q: What are the advantages of TFT LCD compared with CRT?

A: In a CRT monitor, a gun shoots electrons and general light by colliding polarized

electrons on fluorescent glass. Therefore, CRT monitors basically operate with an analog
RGB signal. A TFT LCD monitor is a device that displays an input image by operating a
liquid crystal panel. The TFT has a fundamentally different structure than a CRT: Each cell

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/saf_faq.htm (6 of 9)6/30/2004 11:37:11 AM

FAQs (Frequently Asked Questions)

has an active matrix structure and independent active elements. A TFT LCD has two glass
panels and the space between them is filled with liquid crystal. When each cell is connected
with electrodes and impressed with voltage, the molecular structure of the liquid crystal is
altered and controls the amount of inlet lighting to display images. A TFT LCD has several
advantages over a CRT, since it can be very thin and no flickering occurs because it does
not use the scanning method.

Q: Why is a vertical frequency of 60Hz optimal for an LCD monitor?

A: Unlike a CDT monitor, the TFT LCD panel has a fixed resolution. For example, an XGA

monitor has 1024x3 (R, G, B) x 768 pixels and a higher resolution may not be available
without additional software processing. The panel is designed to optimise the display for a
65MHz dot clock, one of the standards for XGA displays. Since the vertical/horizontal
frequency for this dot clock is 60Hz/48kHz, the optimum frequency for this monitor is 60Hz.

Q: What kind of wide-angle technology is available? How does it work?

A: The TFT LCD panel is an element that controls/displays the inlet of a backlight using the

dual-refraction of a liquid crystal. Using the property that the projection of inlet light refracts
toward the major axis of the liquid element, it controls the direction of inlet light and
displays it. Since the refraction ratio of inlet light on liquid crystal varies with the inlet angle
of the light, the viewing angle of a TFT is much narrower than that of a CDT. Usually, the
viewing angle refers to the point where the contrast ratio is 10. Many ways to widen the
viewing angle are currently being developed and the most common approach is to use a
wide viewing angle film, which widens the viewing angle by varying the refraction ratio. IPS
(In Plane Switching) or MVA (Multi Vertical Aligned) is also used to give a wider viewing
angle.

Q: Why is there no flicker on an LCD Monitor?

A: Technically speaking, LCDs do flicker, but the cause of the phenomenon is different from

that of a CRT monitor -- and it has no impact of the ease of viewing. Flickering in an LCD
monitor relates to usually undetectable luminance caused by the difference between
positive and negative voltage. On the other hand, CRT flickering that can irritate the human
eye occurs when the on/off action of the fluorescent object becomes visible. Since the
reaction speed of liquid crystal in an LCD panel is much slower, this troublesome form of
flickering is not present in an LCD display.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/saf_faq.htm (7 of 9)6/30/2004 11:37:11 AM

FAQs (Frequently Asked Questions)

Q: Why is an LCD monitor virtually free of Electro Magnetic Interference?

A: Unlike a CRT, an LCD monitor does not have key parts that generate Electro Magnetic

Interference, especially magnetic fields. Also, since an LCD display utilizes relatively low
power, its power supply is extremely quiet.

RETURN TO TOP OF THE PAGE

Ergonomics, Ecology and Safety Standards

Q:

What is the CE mark?

A: The CE (Conformité Européenne) mark is required to be displayed on all regulated

products offered for sale on the European market. This 'CE' mark means that a product
complies with the relevant European Directive. A European Directive is a European 'Law'
that relates to health, safety, environment and consumer protection, much the same as the U.
S. National Electrical Code and UL Standards.

Q: Does the product conform to general safety standards?

A: Yes. Philips LCD monitors conform to the guidelines of MPR-II and TCO 99 standards for

the control of radiation, electromagnetic waves, energy reduction, electrical safety in the
work environment and recyclability. The specification page provides detailed data on safety
standards.

More information is provided in the

Regulatory Information section.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/saf_faq.htm (8 of 9)6/30/2004 11:37:11 AM

FAQs (Frequently Asked Questions)

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/saf_faq.htm (9 of 9)6/30/2004 11:37:11 AM

Troubleshooting

Troubleshooting

Safety and Troubleshooting • FAQs • Common Problems • Imaging Problems • TV and
Audio Problems • Regulatory Information • Other Related Information

This page deals with problems that can be corrected by the user. If the problem still persists after
you have tried these solutions, contact your nearest Philips dealer.

Common Problems

Having this problem? Check these items

No Picture
(Power LED not lit)

● Make sure the power cord is plugged into

the power outlet and into the back of the
monitor.

No Picture

(Power LED is amber)

● Make sure the computer is turned on.

● Make sure the signal cable is properly

connected to your computer.

● Check to see if the monitor cable has

bent pins.

● The Energy Saving feature may be

activated

Screen says

● Make sure the monitor cable is properly

connected to your computer. (Also refer
to the Quick Set-Up Guide).

● Check to see if the monitor cable has

bent pins.

● Make sure the computer is turned on.

Imaging Problems

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/saf_troub.htm (1 of 4)6/30/2004 11:37:12 AM

Troubleshooting

Display position is incorrect

● Press "MENU" key to select "ADJUST

POSITION" control at PC mode or press
"MENU" and "DOWN" hot keys at front
control together to automatically adjust
the position.

Image vibrates on the screen

● Check that the signal cable is properly

connected to the graphics board or PC.

Vertical flicker appears

● Press "MENU" and "DOWN" hot keys at

front control together to automatically
adjust at PC mode.

● Press "MENU" key to select "AUTO".

Horizontal flicker appears

● Press "MENU" and "DOWN" hot keys at

front control together to automatically
adjust at PC mode.

● Press "MENU" key to select "AUTO".

The screen is too bright or too dark

● Adjust the contrast and brightness in

OSD Main Controls. (The backlight of the
product has a fixed life span. When the
screen becomes dark or begins to flicker,
please contact your dealer.)

An after-image appears

● If an image remains on the screen for an

extended period of time, it may be
imprinted in the screen and leave an
afterimage This usually disappears after
a few hours.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/saf_troub.htm (2 of 4)6/30/2004 11:37:12 AM

Troubleshooting

An afterimage remains after the power
has been turned off.

● This is characteristic of liquid crystal and

is not caused by a malfunction or
deterioration of the liquid crystal. The
afterimage will disappear after a period of
time.

Green, red, blue, dark and white dots
remain.

● The remaining dots are normal

characteristic of the liquid crystal used in
today’s technology.

TV and Audio Problems

Poor TV signal reception

● The proximity of mountains or high

buildings may be responsible for ghost
pictures, echoing or shadows. In this
case, try manually adjusting your
pictures: see 'fine tuning' or adjust the
direction of the outside aerial.

No TV picture

● Have you connected the aerial socket

properly? Have you chosen the right
system? Poorly connected aerial sockets
are often the cause of picture or sound
problems (sometimes the connectors can
become half disconnected if the Monitor
set is moved or turned). Check all
connections.

No sound

● Ensure that the audio cables are firmly

connected to both the audio input
connectors on your Monitor and audio
output connectors on your PC or Video
player.

● If on certain TV channels you receive a

picture but no sound, this means that you
do not have the correct TV system.
Modify the SYSTEM setting.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/saf_troub.htm (3 of 4)6/30/2004 11:37:12 AM

Troubleshooting

For further assistance, refer to the Consumer Information Centres list and contact your local
Philips distributor.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/saf_troub.htm (4 of 4)6/30/2004 11:37:12 AM

Regulatory Information

Regulatory Information

TCO '99 Information • TCO Environmental Requirements • CE Declaration of Conformity • Energy
Star Declaration • Federal Communications Commission (FCC) Notice (U.S. Only) • Commission
Federale de la Communication (FCC Declaration) • EN 55022 Compliance (Czech Republic Only) •
VCCI Class 2 Notice (Japan Only) • MIC Notice (South Korea Only) • Polish Center for Testing and
Certification Notice • North Europe (Nordic Countries) Information • BSMI Notice (Taiwan Only) •
Ergonomie Hinweis (nur Deutschland) • Philips End-of-Life Disposal • Information for UK only

Safety and Troubleshooting • Troubleshooting • Other Related Information • Frequently Asked
Questions (FAQs)

TCO '99 Information

Congratulations! You have just purchased a TCO '99 approved and

labeled product! Your choice has provided you with a product
developed for professional use. Your purchase has also contributed
to reducing the burden on the environment and also to the further
development of environmentally adapted electronics products.

Why do we have environmentally labeled computers?

In many countries, environmental labeling has become an established method for encouraging the
adaptation of goods and services to the environment. The main problem, as far as computers and other
electronics equipment are concerned, is that environmentally harmful substances are used both in the
products and during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of
electronics equipment, most of these potentially damaging substances sooner or later enter nature.

There are also other characteristics of a computer, such as energy consumption levels, that are important
from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of
electricity generation have a negative effect on the environment (e.g. acidic and climate-influencing
emissions, radioactive waste), it is vital to save energy. Electronics equipment in offices is often left running
continuously and thereby consumes a lot of energy.

What does labeling involve?

This product meets the requirements for the TCO'99 scheme which provides for international and
environmental labeling of personal computers. The labeling scheme was developed as a joint effort by the
TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The
Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/regs/regulat.htm (1 of 13)6/30/2004 11:37:14 AM

Regulatory Information

Administration).

Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of
electric and magnetic fields, energy consumption and electrical and fire safety.

The environmental demands impose restrictions on the presence and use of heavy metals, brominated and
chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product
must be prepared for recycling and the manufacturer is obliged to have an environmental policy which must
be adhered to in each country where the company implements its operational policy.

The energy requirements include a demand that the computer and/or display, after a certain period of
inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to
reactivate the computer shall be reasonable for the user.

Labeled products must meet strict environmental demands, for example, in respect of the reduction of
electric and magnetic fields, physical and visual ergonomics and good usability.

Below you will find a brief summary of the environmental requirements met by this product. The complete
environmental criteria document may be ordered from:

TCO Development

SE-114 94 Stockholm, Sweden

Fax: [phone]

Email (Internet): [e-mail]

Current information regarding TCO'99 approved and labeled products may also be obtained via
the Internet, using the address: http://www.tco-info.com/

RETURN TO TOP OF THE PAGE

Environmental Requirements

Flame retardants

Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose
is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can
consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame
retardants are chemically related to another group of environmental toxins, PCBs. Both the flame

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/regs/regulat.htm (2 of 13)6/30/2004 11:37:14 AM

Regulatory Information

retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health
effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative*
processes. Flame retardants have been found in human blood and researchers fear that disturbances in
fetus development may occur.

The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not
contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the
printed circuit boards since no substitutes are available.

Cadmium**

Cadmium is present in rechargeable batteries and in the color-generating layers of certain computer
displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99
requirement states that batteries, the color-generating layers of display screens and the electrical or
electronics components must not contain any cadmium.

Mercury**

Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic
in high doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also
demands that mercury is not present in any of the electrical or electronics components associated with the
labeled unit.

CFCs (freons)

The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the
manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit
boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing
increased reception on earth of ultraviolet light with increased risks e.g. skin cancer (malignant melanoma)
as a consequence.

Lead**

Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous
system and in higher doses, causes lead poisoning. The relevant TCO'99 requirement permits the inclusion
of lead since no replacement has yet been developed.

* Bio-accumulative is defined as substances which accumulate within living organisms.

** Lead, Cadmium and Mercury are heavy metals which are bio-accumulative.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/regs/regulat.htm (3 of 13)6/30/2004 11:37:14 AM

Regulatory Information

CE Declaration of Conformity

Philips Consumer Electronics declare under our responsibility that the product is in conformity with the
following standards

- EN60950:2000 (Safety requirement of Information Technology Equipment)

- EN55022:1998 (Radio Disturbance requirement of Information Technology Equipment)

- EN55024:1998 (Immunity requirement of Information Technology Equipment)

- EN61000-3-2:1995 (Limits for Harmonic Current Emission)

- EN61000-3-3:1995 (Limitation of Voltage Fluctuation and Flicker)

- EN55013:1990+A12+A13+A14 (Radio Disturbance requirement of Sound and Television Receivers and
associated)

- EN55020:1994+A12 (Immunity requirement of Sound and Television Receivers and associated)

- IEC Guide 112:2000 ( Guide on the Safety of Multimedia Equipment) following provisions of directives
applicable

- 73/23/EEC (Low Voltage Directive)

- 89/336/EEC (EMC Directive)

- 93/68/EEC (Amendment of EMC and Low Voltage Directive)
and is produced by a manufacturing organization on ISO9000 level.

The product also comply with the following standards

- ISO9241-3, ISO9241-7, ISO9241-8 (Ergonomic requirement for Visual Display)

- ISO13406-2 (Ergonomic requirement for Flat panels)

- GS EK1-2000 (GS specification)

- prEN50279:1998 (Low Frequency Electric and Magnetic fields for Visual Display)

- MPR-II (MPR:1990:8/1990:10 Low Frequency Electric and Magnetic fields)

- TCO95, TCO99 (Requirement for Environment Labelling of Ergonomics, Energy, Ecology and Emission,
TCO: Swedish Confederation of Professional Employees) for TCO versions

RETURN TO TOP OF THE PAGE

Energy Star Declaration

PHILIPS
170T4

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/regs/regulat.htm (4 of 13)6/30/2004 11:37:14 AM

Regulatory Information

This monitor is equipped with a function for saving energy which supports the VESA Display
Power Management Signaling (DPMS) standard. This means that the monitor must be
connected to a computer which supports VESA DPMS to fulfill the requirements in the NUTEK
specification 803299/94. Time settings are adjusted from the system unit by software.

NUTEK VESA State LED Indicator Power Consumption
Normal operation ON Green 55 W (typical)
Power Saving

Alternative 2
One step

OFF Amber

110VAC < 1W
230VAC < 2W

As an ENERGY STAR

®

Partner, PHILIPS has determined that this product

meets the

ENERGY STAR® guidelines for energy efficiency.

We recommend you switch off the monitor when it is not in use for quite a long time.

RETURN TO TOP OF THE PAGE

Federal Communications Commission (FCC) Notice (U.S. Only)

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/regs/regulat.htm (5 of 13)6/30/2004 11:37:14 AM

Regulatory Information

● Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer
device.

To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or
excessive moisture.

THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.

RETURN TO TOP OF THE PAGE

Commission Federale de la Communication (FCC Declaration)

Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques
de class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues
de façon à fourir une protection raisonnable contre les interférences nuisibles dans le
cadre d'une installation résidentielle. CET appareil produit, utilise et peut émettre des
hyperfréquences qui, si l'appareil n'est pas installé et utilisé selon les consignes
données, peuvent causer des interférences nuisibles aux communications radio.
Cependant, rien ne peut garantir l'absence d'interférences dans le cadre d'une
installation particulière. Si cet appareil est la cause d'interférences nuisibles pour la
réception des signaux de radio ou de télévision, ce qui peut être décelé en fermant
l'équipement, puis en le remettant en fonction, l'utilisateur pourrait essayer de
corriger la situation en prenant les mesures suivantes:

● Réorienter ou déplacer l'antenne de réception.

● Augmenter la distance entre l'équipement et le récepteur.

● Brancher l'équipement sur un autre circuit que celui utilisé par le récepteur.

● Demander l'aide du marchand ou d'un technicien chevronné en radio/télévision.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/regs/regulat.htm (6 of 13)6/30/2004 11:37:14 AM

Regulatory Information

Toutes modifications n'ayant pas reçu l'approbation des services compétents en
matière de conformité est susceptible d'interdire à l'utilisateur l'usage du présent
équipement.

N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques.

CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU
REGLEMENT SUR LE MATERIEL BROUILLEUR DU CANADA.

RETURN TO TOP OF THE PAGE

EN 55022 Compliance (Czech Republic Only)

RETURN TO TOP OF THE PAGE

VCCI Notice (Japan Only)

This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI) for
Information technology equipment. If this equipment is used near a radio or television receiver in a
domestic environment, it may cause radio Interference. Install and use the equipment according to the
instruction manual.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/regs/regulat.htm (7 of 13)6/30/2004 11:37:14 AM

Regulatory Information

Class B ITE

RETURN TO TOP OF THE PAGE

MIC Notice (South Korea Only)

Class B Device

Please note that this device has been approved for non-business purposes and may be used in any
environment, including residential areas.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/regs/regulat.htm (8 of 13)6/30/2004 11:37:14 AM

Regulatory Information

RETURN TO TOP OF THE PAGE

Polish Center for Testing and Certification Notice

The equipment should draw power from a socket with an attached protection circuit (a three-prong socket).
All equipment that works together (computer, monitor, printer, and so on) should have the same power
supply source.

The phasing conductor of the room's electrical installation should have a reserve short-circuit protection
device in the form of a fuse with a nominal value no larger than 16 amperes (A).

To completely switch off the equipment, the power supply cable must be removed from the power supply
socket, which should be located near the equipment and easily accessible.

A protection mark "B" confirms that the equipment is in compliance with the protection usage requirements
of standards PN-93/T-42107 and PN-89/E-06251.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/regs/regulat.htm (9 of 13)6/30/2004 11:37:14 AM

Regulatory Information

North Europe (Nordic Countries) Information

Placering/Ventilation

VARNING:

FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR
DU STÄLLER DIN UTRUSTNING PÅPLATS.

Placering/Ventilation

ADVARSEL:

SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT
ER NEMT TILGÆNGELIGE.

Paikka/Ilmankierto

VAROITUS:

SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI
IRROTTAA PISTORASIASTA.

Plassering/Ventilasjon

ADVARSEL:

NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR
STØMTILFØRSEL ER LETTE Å NÅ.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/regs/regulat.htm (10 of 13)6/30/2004 11:37:14 AM

Regulatory Information

BSMI Notice (Taiwan Only)

RETURN TO TOP OF THE PAGE

Ergonomie Hinweis (nur Deutschland)

Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht, ist darauf zu achten, daß

1. Reparaturen nur durch Fachpersonal durchgeführt werden.

2. nur original-Ersatzteile verwendet werden.

3. bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird.

Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem
Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringem
Zeichenkontrast wären die Folge).

Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger.

ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß
NETZSTECKER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND.

RETURN TO TOP OF THE PAGE

End-of-Life Disposal

Your new monitor contains materials that can be recycled and reused. Specialized companies can recycle
your product to increase the amount of reusable materials and to minimize the amount to be disposed of.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/regs/regulat.htm (11 of 13)6/30/2004 11:37:14 AM

Regulatory Information

Please find out about the local regulations on how to dispose of your old monitor from your local Philips
dealer.

(For customers in Canada and U.S.A.)

This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal
regulations.
For additional information on recycling contact

www.eia.org (Consumer Education Initiative)

RETURN TO TOP OF THE PAGE

Information for UK only

WARNING - THIS APPLIANCE MUST BE
EARTHED.

Important:

This apparatus is supplied with an approved
moulded 13A plug. To change a fuse in this type
of plug proceed as follows:

1. Remove fuse cover and fuse.

2. Fit new fuse which should be a BS 1362 5A,A.
S.T.A. or BSI approved type.

3. Refit the fuse cover.

If the fitted plug is not suitable for your socket
outlets, it should be cut off and an appropriate 3­pin plug fitted in its place.

If the mains plug contains a fuse, this should
have a value of 5A. If a plug without a fuse is
used, the fuse at the distribution board should
not be greater than 5A.

Note: The severed plug must be destroyed to
avoid a possible shock hazard should it be
inserted into a 13A socket elsewhere.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/regs/regulat.htm (12 of 13)6/30/2004 11:37:14 AM

Regulatory Information

How to connect a plug

The wires in the mains lead are coloured in
accordance with the following code:

BLUE - "NEUTRAL" ("N")

BROWN - "LIVE" ("L")

GREEN & YELLOW - "EARTH" ("E")

1. The GREEN AND YELLOW wire must be
connected to the terminal in the plug which is
marked with the letter "E" or by the Earth symbol

or coloured GREEN or GREEN AND

YELLOW.

2. The BLUE wire must be connected to the
terminal which is marked with the letter "N" or
coloured BLACK.

3. The BROWN wire must be connected to the
terminal which marked with the letter "L" or
coloured RED.

Before replacing the plug cover, make certain
that the cord grip is clamped over the sheath of
the lead - not simply over the three wires.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/regs/regulat.htm (13 of 13)6/30/2004 11:37:14 AM

Other Related Information

Other Related Information

Safety and Troubleshooting • FAQs • Troubleshooting • Regulatory Information • Information
for Users in the U. S. • Information for Users Outside the U.S

Information for Users in the U. S.

For units set at 115 V :

Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord
a maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V.

For units set at 230 V:

Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord
a maximum of 15-feet long and a tandem blade, grounding type attachment plug rated 15 A, 250 V.

Information for Users outside the U.S.

For units set at 230 V:

Use a Cord Set consisting of a minimum 18 AWG cord and grounding type attachment plug rated
15 A, 250 V. The Cord Set should have the appropriate safety approvals for the country in which
the equipment will be installed and / or be marked HAR.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/safety/saf_other.htm6/30/2004 11:37:14 AM

Philips Pixel Defect Policy

Philips Pixel Defect Policy

Product Features • Technical Specifications • Resolution & Preset Modes • Automatic Power
Saving • Physical Specification • Pin Assignment • Product Views

Philips' LCD Panel Pixel Defect Policy

Philips strives to deliver the highest quality products. We use some of the industry's most advanced
manufacturing processes and practice stringent quality control. However, pixel or sub pixel defects
on the TFT LCD panels used in flat panel monitors are sometimes unavoidable. No manufacturer
can guarantee that all panels will be free from pixel defects, but Philips guarantees that any monitor
with an unacceptable number of defects will be repaired or replaced under warranty. This notice
explains the different types of pixel defects and defines acceptable defect levels for each type. In
order to qualify for repair or replacement under warranty, the number of pixel defects on a TFT LCD
panel must exceed these acceptable levels. For example, no more than 0.0004% of the sub pixels
on a 15" XGA monitor may be defective. Furthermore, Philips sets even higher quality standards for
certain types or combinations of pixel defects that are more noticeable than others. This policy is
valid worldwide.

Pixels and Sub pixels

A pixel, or picture element, is composed of three sub pixels in the primary colors of red, green and
blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored
subpixels together appear as a single white pixel. When all are dark, the three colored sub pixels
together appear as a single black pixel. Other combinations of lit and dark sub pixels appear as
single pixels of other colors.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/product/pixel.htm (1 of 4)6/30/2004 11:37:24 AM

Philips Pixel Defect Policy

Types of Pixel Defects

Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel
defects and several types of sub pixel defects within each category.

Bright Dot Defects appear as pixels or sub pixels that are always lit or 'on'. These are the types of

bright dot defects:

One lit red, green or blue
sub pixel

Two adjacent lit sub pixels:

- Red + Blue = Purple

- Red + Green = Yellow

- Green + Blue = Cyan (Light Blue)

Three adjacent lit sub pixels
(one white pixel)

Black Dot Defects appear as pixels or sub pixels that are always dark or 'off'. These are the types of

black dot defects:

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/product/pixel.htm (2 of 4)6/30/2004 11:37:24 AM

Philips Pixel Defect Policy

One dark sub pixel Two or three adjacent dark sub pixels

Proximity of Pixel Defects

Because pixel and sub pixels defects of the same type that are near to one another may be more
noticeable, Philips also specifies tolerances for the proximity of pixel defects.

Pixel Defect Tolerances

In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT
LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the
tolerances listed in the following tables.

BRIGHT DOT DEFECTS ACCEPTABLE LEVEL

MODEL

150T4/170T4

1 lit sub pixel 4 or fewer
2 adjacent lit sub pixels 2 or fewer
3 adjacent lit sub pixels

(one white pixel)

0

Distance between two
bright dot defects*

15 mm or more

Total bright dot defects
of all types

4 or fewer

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/product/pixel.htm (3 of 4)6/30/2004 11:37:24 AM

Philips Pixel Defect Policy

BLACK DOT DEFECTS ACCEPTABLE LEVEL

MODEL

150T4/170T4

1 dark sub pixel 4 or fewer
2 adjacent dark sub

pixels

2 or fewer

3 adjacent dark sub
pixels

0

Distance between two
black dot defects*

15 mm or more

Total black dot defects
of all types

4 or fewer

TOTAL DOT DEFECTS ACCEPTABLE LEVEL

MODEL

150T4/170T4

Total bright or black dot
defects of all types

5 or fewer

Note:

* 1 or 2 adjacent sub pixel defects = 1 dot defect

All Philips monitors are ISO13406-2 Compliant

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/product/pixel.htm (4 of 4)6/30/2004 11:37:24 AM

Connecting to Your PC, TV Antenna, DVD/VCR etc.

Connecting to Your PC, TV Antenna, DVD/VCR etc.

Front View Product Description • Accessory Pack • Connecting to Your PC, TV Antenna,
DVD/VCR etc. • VESA Mounting and Easy Wall Mounting • Installing the Optional TV/AV
Module • Getting Started • Optimizing Performance

Accessory Pack

Unpack all the parts.

Power cable Remote control & batteries

PC audio-in cable VGA signal cable

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/connect.htm (1 of 8)6/30/2004 11:37:36 AM

Connecting to Your PC, TV Antenna, DVD/VCR etc.

Tuner adapter

Power adapter

(Use only AC/DC adapter model

0218B1664 or ADP-64BB B)

Wall mount kit E-DFU pack

TV/AV module

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/connect.htm (2 of 8)6/30/2004 11:37:36 AM

Connecting to Your PC, TV Antenna, DVD/VCR etc.

Setting up and connecting your monitor/TV

Ensure that the power to the monitor/TV is switched off before the installation.

A) Connecting to PC computer

1. Connect the power cord to the DC IN power connector on the back of the
monitor.

2. Connect the 15-pin D-SUB of the video signal cable to the VGA connector on
the back of the monitor

Note: If you use an Apple Macitosh

TM

, you need to connect the special Mac

adapter to one end of the monitor signal cable.

3. Connect the stereo audio cable to PC AUDIO IN on the back of the monitor and
the other end to AUDIO OUT terminal of the sound card on your PC.

Note: If necessary, please install monitor driver contained on the accompanied
CD. For driver installation, see the Monitor Driver Installation section (Getting

Started).

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/connect.htm (3 of 8)6/30/2004 11:37:36 AM

Connecting to Your PC, TV Antenna, DVD/VCR etc.

RETURN TO TOP OF THE PAGE

B) Connecting to a external A/V device such as a DVD/VCR/VCD

1. Connect RCA (Yellow) or S-VHS cable to an appropriate external AV device
such as DVD/VCR.

2. Connect RCA audio cable to AUDIO (R) and AUDIO (L) terminal and the other
ends to corresponding audio out terminals on the AV device.

3. Headphone may be connected to the headphone output on the side of the
monitor marked

. While the headphone is connected, the sound from the

external speakers will be disable.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/connect.htm (4 of 8)6/30/2004 11:37:36 AM

Connecting to Your PC, TV Antenna, DVD/VCR etc.

RETURN TO TOP OF THE PAGE

C) Connecting to TV/CATV

1. Connect an antenna or CATV cable to the antenna port of tuner box.

RETURN TO TOP OF THE PAGE

Using the Cable Management

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/connect.htm (5 of 8)6/30/2004 11:37:36 AM

Connecting to Your PC, TV Antenna, DVD/VCR etc.

1) Remove the arm box's top cover.

Press the center of the cap and open the cap from sides (Do not attempt to open the cap
from the top or the bottom)

2) Place the cables inside the arm box.

3) Replace top cover.

We recommend you follow intelligent cable management to reduce the electrical
alternating field to low level as not to burden the work environment with unnecessary
factors.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/connect.htm (6 of 8)6/30/2004 11:37:36 AM

Connecting to Your PC, TV Antenna, DVD/VCR etc.

To attach and remove back cover

To attach back cover

1) Line up in ventilation.

Before attempting to seal the cover,
make sure it is properly aligned with the
upper hooks.

2) Use hands to push and seal in place.

To remove back cover

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/connect.htm (7 of 8)6/30/2004 11:37:36 AM

Connecting to Your PC, TV Antenna, DVD/VCR etc.

1) Lift off the rear cover from the top

hooks at an angle of less than 30
degrees to avoid hook damage.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/connect.htm (8 of 8)6/30/2004 11:37:36 AM

VESA Mounting and Easy Wall Mounting

VESA Mounting and Easy Wall Mounting

Front View Product Description • Accessory Pack • Connecting to Your PC, TV Antenna,
DVD/VCR etc. • Installing the Optional TV/AV Module • Getting Started • Optimising
Performance

Unfold the base • Fold the base • Foldable base available for easy wall mounting • VESA
Wall Mounting

Unfold and Fold the Base

Unfold the Base

1) Place monitor face down on

a safe surface

2) Pull up the base

Fold the Base

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/base.htm (1 of 5)6/30/2004 11:37:37 AM

VESA Mounting and Easy Wall Mounting

1) Push down the head of monitor.

Make sure the back cover is
removed when folding the base.

Foldable base available for easy wall mounting

Make sure the back cover is removed before mounting the monitor on the wall.

Smart tips

1. Use the full scale template to mark on the wall the horizontal distance (130 mm)
between the two mounting screws.

Notes:

- The surface for mounting area must be flat and larger than the pedestal.

- The wall must support a pull force of 10 kg for each screw.

2. At the locations marked, drill two holes in the wall, each 7 mm in diameter and 25
mm in depth.

3. Securely insert the plastic wall anchors (1) and then use the two screws (2) to

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/base.htm (2 of 5)6/30/2004 11:37:37 AM

VESA Mounting and Easy Wall Mounting

fasten the mounting pedestal to the wall.

WARNING!

● Read all instructions carefully before mounting!

● Correct assembly is essential. The maximum allowed weight of the LCD Display is

6.5 kg/14.3 lbs.

● The assembly materials that come with the product are only suitable for attachment

to solid wood, brick or concrete walls.

● For wood walls: Discard the wall anchors! Drill each hole 3.6 mm in diameter and

20 mm in depth.

● To avoid possible injury, do not mount above a sofa or bed.

The manufacturer accepts no liability for improper installations or installations not
performed in accordance with these instructions.

RETURN TO TOP OF THE PAGE

VESA Wall Mounting

A) Remove the base

1) Remove the arm box's top cover.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/base.htm (3 of 5)6/30/2004 11:37:37 AM

VESA Mounting and Easy Wall Mounting

2) Remove the hinge cape.

3) Remove the 4 screws and then

remove the base from the LCD
monitor.

B) Attaching a wall or arm mounting device.

Note: This monitor accepts a 100mmx100mm VESA-Compliant mounting interface.

The monitor support VESA mounting standard for use with various VESA mounting
devices. To install any VESA mounting devices, please follow the instructions given.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/base.htm (4 of 5)6/30/2004 11:37:37 AM

VESA Mounting and Easy Wall Mounting

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/base.htm (5 of 5)6/30/2004 11:37:37 AM

Installing the Optional TV/AV Module

Installing the Optional TV/AV Module

Front View Product Description • Connecting to Your PC, TV Antenna, DVD/VCR etc. •
VESA Mounting and Easy Wall Mounting • Getting Started • Optimising Performance

Optional TV/AV Module: Detach the TV module cover • Install the TV module

Detach the TV module cover

1) Firmly grip the handle as shown and slide out to

release the cover.

RETURN TO TOP OF THE PAGE

Install the TV module

a) Pull down the handle grip towards the center.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/module.htm (1 of 2)6/30/2004 11:37:37 AM

Installing the Optional TV/AV Module

b) Slide the TV module and firmly lock into

place.

c) Stow the handle grip to secure the TV

module.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/module.htm (2 of 2)6/30/2004 11:37:37 AM

Getting Started

Getting Started

Front View Product Description • Connecting to Your PC, TV Antenna, DVD/VCR etc. •
VESA Mounting and Easy Wall Mounting • Installing the Optional TV/AV Module •
Getting Started • Optimizing Performance

Getting Started

Use the information file ( .inf) for Windows® 95/98/2000/Me/XP or later

The built-in VESA DDC2B feature in Philips Monitors supports Plug & Play requirements for
Windows® 95/98/2000/Me/XP. This information file ( .inf) should be installed in order that your
Philips monitor can be enabled from the 'Monitor' dialog box in Windows® 95/98/2000/Me/XP
and the Plug & Play application can be activated. The installation procedure based on
Windows® '95 OEM Release 2 , 98 , Me, XP and 2000 is specified as follows.

For Windows® 95

1. Start Windows® '95

2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.

3. Double click on the 'Display' Icon.

4. Select the 'Settings' tab then click on 'Advanced...'.

5. Select the 'Monitor' button, point to 'Change...' then click on 'Have Disk...'.

6. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click

on the 'OK' button.

7. Click on the 'OK' button then select your monitor model and click on 'OK'.

8. Click on the 'Close' button.

For Windows® 98

1. Start Windows® 98

2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.

3. Double click on the 'Display' Icon.

4. Select the 'Settings' tab then click on 'Advanced...'.

5. Select the 'Monitor' button, point to 'Change...' then click on 'Next'

6. Select 'Display a list of all the drivers in a specific location, so you can choose the driver

you want.' then click on 'Next' and then click on 'Have Disk...'.

7. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click

on the 'OK' button.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/gt_start.htm (1 of 3)6/30/2004 11:37:38 AM

Getting Started

8. Click on the 'OK' button then select your monitor model and click on the 'Next' button.

9. Click on the 'Finish' button then the 'Close' button.

For Windows® Me

1. Start Windows® Me

2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.

3. Double click on the 'Display' Icon.

4. Select the 'Settings' tab then click on 'Advanced...'.

5. Select the 'Monitor' button, then click on 'Change...' button.

6. Select 'Specify the location of the driver(Advanced)' and click on the 'Next' button.

7. Select 'Display a list of all the drivers in a specific location, so you can choose the driver

you want', then click on 'Next' and then click on 'Have Disk...'.

8. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click

on the 'OK' button.

9. Click on the 'OK' button, select your monitor model and click on the 'Next' button.

10. Click on 'Finish' button then the 'Close' button.

For Windows® 2000

1. Start Windows® 2000

2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.

3. Double click on the 'Display' Icon.

4. Select the 'Settings' tab then click on 'Advanced...'.

5. Select 'Monitor'

- If the 'Properties' button is inactive, it means your monitor is properly configured. Please
stop installation.

- If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps
given below.

6. Click on 'Driver' and then click on 'Update Driver...' then click on the 'Next' button.

7. Select 'Display a list of the known drivers for this device so that I can choose a specific

driver', then click on 'Next' and then click on 'Have disk...'.

8. Click on the 'Browse...' button then select the appropriate drive F: ( CD-ROM Drive).

9. Click on the 'Open' button, then click on the 'OK' button.

10. Select your monitor model and click on the 'Next' button.

11. Click on the 'Finish' button then the 'Close' button.

If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button.

For Windows® XP

1. Start Windows® XP

2. Click on the 'Start' button and then click on 'Control Panel'.

3. Select and click on the category 'Printers and Other Hardware'

4. Click on the 'Display' Item.

5. Select the 'Settings' tab then click on the 'Advanced' button.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/gt_start.htm (2 of 3)6/30/2004 11:37:38 AM

Getting Started

6. Select 'Monitor' tab

- If the 'Properties' button is inactive, it means your monitor is properly configured. Please
stop installation.

- If the 'Properties' button is active, click on 'Properties' button.
Please follow the steps below.

7. Click on the 'Driver' tab and then click on 'Update Driver...' button.

8. Select the 'Install from a list or specific location [advanced]' radio button and then click on

the 'Next' button.

9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the

'Next' button.

10. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the

appropriate drive F: (CD-ROM Drive).

11. Click on the 'Open' button, then click the 'OK' button.

12. Select your monitor model and click on the 'Next' button.

- If you can see the 'has not passed Windows® Logo testing to verify its compatibility with
Windows® XP' message, please click on the 'Continue Anyway' button.

13. Click on the 'Finish' button then the 'Close' button.

14. Click on the 'OK' button and then the 'OK' button again to close the Display_Properties

dialog box.

If your Windows® 95/98/2000/Me/XP version is different or you need more detailed installation
information, please refer to Windows® 95/98/2000/Me/XP user's manual.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/install/gt_start.htm (3 of 3)6/30/2004 11:37:38 AM

Using other menus (Europe area)

Using Other Menus (Europe Area)

● Using the Remote Control

● Selecting a source input

● Adjusting the picture preference

● Adjusting the sound preference

● Selecting a preferred OSD language

● Screen modes

● Automatic tuning • Manual tuning • Skipping programmes

Using the Remote Control

1. Press

to activate the control menu display.

2. Use

, to scroll the highlighted item to be selected.

3. Use to select the item to be changed.

4. Use

, again to scroll the highlighted sub-item to be selected.

5. Use , to adjust the value of selected item. Or use to select the desired
option.

6. When the setting is correct, use

, to highlight EXIT item and press to exit

from the menu. The menu OSD will disappear.

7. The menu will disappear automatically after a few seconds without any key having to
be pressed.

RETURN TO TOP OF THE PAGE

Selecting a source input

1. Press

to activate the menu.

2. Use

, to scroll the highlight INPUT SELECT, and then press .

3. Use

, to highlight the input source to be selected. There are five input sources:

● PC

● TV

● AV

● S-video

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_eu.htm (1 of 6)6/30/2004 11:37:48 AM

Using other menus (Europe area)

● HD-YPbPr

4. Press

to select the input source.

RETURN TO TOP OF THE PAGE

Adjusting the picture preference

1. Press

to activate the menu.

2. Use

, to scroll the highlight PICTURE, and then press .

3.

Use

, to highlight the picture parameter to be adjusted. There are 5 parameters:

● BRIGHTNESS: adjusts screen brightness.

● CONTRAST: alters the variation between light and dark tones.

● COLOUR: alters the colour darkness.

● SHARPNESS: alters the crispness of the image.

● COLOUR TEMP (colour temperature): adjusts the colour temperature of the picture.

Three options are available here:
COOL (blue white), NORMAL (balanced) or WARM (red white).

4. Press

, to adjust BRIGHTNESS, CONTRAST, COLOUR, SHARPNESS. Or,

press to further change COLOUR TEMP setting.

5. Use

, to highlight EXIT and then press to exit from the menu.

RETURN TO TOP OF THE PAGE

Adjusting the sound preference

1. Press

to activate the menu.

2. Use

, to scroll the highlight SOUND, and then press .

3. Use

, to highlight the sound parameter to be adjusted. There are 4 parameters:

● TREBLE: alters the level of the high frequency sound.

● BASS: alters the level of the low frequency sound.

● BALANCE: to balance the sound between the left and right speakers.

● SURROUND ON/OFF: to turn the surrounding sound effect on or off.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_eu.htm (2 of 6)6/30/2004 11:37:48 AM

Using other menus (Europe area)

4. Press , to adjust the selected parameter.

5. Use

, to highlight EXIT and then press to exit from the menu.

RETURN TO TOP OF THE PAGE

Selecting a preferred OSD language

1. Press

to activate the menu.

2. Use , to scroll the highlight LANGUAGE, and then press .

3. Use

, to highlight the language to be selected. There are 5 languages:

● ENGLISH

●

●

● DEUTSCH

● ITALIANO

4. Press to select the language.

5. Use , to highlight EXIT and then press to exit from the menu.

RETURN TO TOP OF THE PAGE

Screen modes

This

menu allows you to set your screen display mode to match the input video aspect ratio.

1. Press to activate the menu.

2. Use

, to scroll the highlight VIDEO MODE, and then press to activate the

video mode menu.

3. Press

, keys to highlight one mode:

● Standard

mode

Display pictures of 16:9
aspect ratio (HD
broadcasting)

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_eu.htm (3 of 6)6/30/2004 11:37:48 AM

Using other menus (Europe area)

● 4:3 mode Display pictures of normal

size (that is, a 4:3 aspect
ratio)

● Full screen

mode

Enlarge horizontally
extended pictures equally
in all directions to
maintain the aspect ratio
constant.

● Nonlinear

mode

Ideal for displaying
vertically extended
pictures such as
squeezed pictures and
recorded HD programs.

4. Press to select the mode.

5. Use

, to highlight EXIT and then press to exit from the menu.

RETURN TO TOP OF THE PAGE

Automatic tuning

This menu allows you to automatically search for all the programmes available in your region
(or on your cable network).

1. Press to activate the menu.

2. Use

, to scroll the highlight INSTALL, and then press .

3. Use

, to scroll the highlight SYSTEM, and then press .

4. Press

, keys to select your region. There are two choices:

● WEST EUR

● FRANCE

5. Press

to return the install menu.

6. Use

, to scroll the highlight AUTO STORE, and then press to activate the

automatic searching. After several minutes, the INSTALL menu reappears

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_eu.htm (4 of 6)6/30/2004 11:37:48 AM

Using other menus (Europe area)

automatically.

7. The programmes found will be numbered in descending order, starting with 0, 1, 2,
etc. Use the SKIP menu to enable or disable the programmes which you want to be
skipped. When you use P UP/DOWN to access a programme, all disabled
programmes will be skipped.

RETURN TO TOP OF THE PAGE

Manual tuning

This menu allows you to store the programmes one by one by hand.

1. Press

to activate the menu.

2. Use

, to scroll the highlight INSTALL, and then press .

3. Use

, to scroll the highlight MANUAL STORE, and then press .

4. Use

, to scroll the highlight SEARCH and press .The search begins.
As soon as a programme is found, the search will stop. If you know the frequency of
the programme required, enter its number directly using the 0-9 keys and go to step 6.

5. If reception is unsatisfactory, select FINE TUNE and hold down or key.

6. Select PROG. NO (programme number) and use the or to change the desired

number.

7. Select STORE and press . The message STORED appears. The programme is
stored.

8. Repeat steps 4 to 7 for each programme to be stored.

RETURN TO TOP OF THE PAGE

Skipping programmes

This menu allows you to set the skipped programmes when you use p +/- keys to access the
programme.

1. Press to activate the menu.

2. Use

, to scroll the highlight INSTALL, and then press .

3. Use

, to scroll the highlight CHANNEL SKIP, and then press .

4. Use [P UP] or [P DN] keys to view the programme in the list.

5. Select the programme you wish to skip or not skip using or keys. The skip

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_eu.htm (5 of 6)6/30/2004 11:37:48 AM

Using other menus (Europe area)

function will be toggled on or off.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_eu.htm (6 of 6)6/30/2004 11:37:48 AM

Using other menus (AP)

Using Other Menus (Asia Pacific Area and China excluding
Korea, Taiwan, and Philippines)

● Using the Remote Control

● Selecting a source input

● Adjusting the picture preference

● Adjusting the sound preference

● Selecting a preferred OSD language

● Video mode

● Automatic tuning • Manual tuning • Skipping programmes

Using the Remote Control

1. Press

to activate the control menu display.

2. Use

, to scroll the highlighted item to be selected.

3. Use to select the item to be changed.

4. Use

, again to scroll the highlighted sub-item to be selected.

5. Use , to adjust the value of selected item. Or use to select the desired
option.

6. When the setting is fine, use

, to highlight EXIT item and press to exit from

the menu. The menu OSD will disappear.

7. Menu will disappear automatically after few seconds while no key was pressed.

RETURN TO TOP OF THE PAGE

Selecting a source input

1. Press

to activate the menu.

2. Use

, to scroll the highlight INPUT SELECT, and then press .

3. Use

, to highlight the input source to be selected. There are 5 input sources:

● PC

● TV

● AV

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_ap.htm (1 of 6)6/30/2004 11:37:49 AM

Using other menus (AP)

● S-video

● HD-YPbPr

4. Press

to select the input source.

RETURN TO TOP OF THE PAGE

Adjusting the picture preference

1. Press

to activate the menu.

2. Use

, to scroll the highlight PICTURE, and then press .

3.

Use

, to highlight the picture parameter to be adjusted. There are five parameters:

● BRIGHTNESS: alters the brightness of the image.

● CONTRAST: alters the variation between light and dark tones.

● COLOUR: alters the colour intensity.

● SHARPNESS: alters the crispness of the image.

● COLOUR TEMP (colour temperature): adjusts the colour temperature of the picture.

Three options are available here:
COOL (blue white), NORMAL (balanced) or WARM (red white).

4. Press

, to adjust BRIGHTNESS, CONTRAST, COLOUR, SHARPNESS. Or,

press to further change COLOUR TEMP setting.

5. Use

, to highlight EXIT and then press to exit from the menu.

RETURN TO TOP OF THE PAGE

Adjusting the sound preference

1. Press

to activate the menu.

2. Use

, to scroll the highlight SOUND, and then press .

3. Use

, to highlight the sound parameter to be adjusted. There are 4 parameters:

● TREBLE: alters the level of the high frequency sound.

● BASS: alters the level of the low frequency sound.

● BALANCE: to balance the sound between the left and right speakers.

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_ap.htm (2 of 6)6/30/2004 11:37:49 AM

Using other menus (AP)

● SURROUND ON/OFF: to turn the surrounding sound effect on or off.

4. Press

, to adjust the selected parameter.

5. Use

, to highlight EXIT and then press to exit from the menu.

RETURN TO TOP OF THE PAGE

Selecting a preferred OSD language

1. Press

to activate the menu.

2. Use , to scroll the highlight LANGUAGE, and then press .

3. Use

, to highlight the language to be selected. There are two languages:

● ENGLISH

●

4. Press to select the language.

5. Use

, to highlight EXIT and then press to exit from the menu.

RETURN TO TOP OF THE PAGE

Video Mode

This menu allows you to set your screen display mode to match the input video aspect ratio.

1. Press to activate the menu.

2. Use

, to scroll the highlight VIDEO MODE, and then press to activate the

video mode menu.

3. Press

, keys to highlighte mode:

● Standard

mode

Display pictures of 16:9
aspect ratio (HD
broadcasting)

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_ap.htm (3 of 6)6/30/2004 11:37:49 AM

Using other menus (AP)

● 4:3 mode

Display pictures of normal
size (that is, a 4:3 aspect
ratio)

● Full screen

mode

Enlarge horizontally
extended pictures equally in
all directions to maintain the
aspect ratio constant.

● Nonlinear

mode

Ideal for displaying vertically
extended pictures such as
squeezed pictures and
recorded HD programs.

4. Press to select the mode.

5. Use

, to highlight EXIT and then press to exit from the menu.

RETURN TO TOP OF THE PAGE

Automatic tuning

This menu allows you to automatically search for all the programmes available in your region
(or on your cable network).

1. Press to activate the menu.

2. Use

, to scroll the highlight INSTALL, and then press .

3. Use

, to scroll the highlight AUTO STORE, and then press to activate the
automatic searching. After several minutes, the INSTALL menu reappears
automatically.

4. The programmes found will be numbered in ascending order starting at 0, 1, 2, etc.
Use the SKIP menu to enable or disable the programmes which you want it to be
skipped. When you use P UP/DOWN to access programme, all disable programmes
will be skipped.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_ap.htm (4 of 6)6/30/2004 11:37:49 AM

Using other menus (AP)

Manual tuning

This menu allows you to store the programmes one by one by hand.

1. Press to activate the menu.

2. Use

, to scroll the highlight INSTALL, and then press .

3. Use

, to scroll the highlight MANUAL STORE, and then press .

4. Use

, to scroll the highlight SEARCH and press .The search begins.
As soon as a programme is found, the search will stop. If you know the frequency of
the programme required, enter its number directly using the 0, 9 keys and go to step

6.

5. If reception is unsatisfactory, select FINE TUNE and hold down or key.

6. Select PROG. NO (programme number) and use the or to change the desired

number.

7. Select STORE and press . The message STORED appears. The programme is
stored.

8. Repeat steps 4 to 7 for each programme to be stored.

RETURN TO TOP OF THE PAGE

Skipping programmes

This menu allows you to set the skipped programmes when you use p +/- keys to access the
programme.

1. Press

to activate the menu.

2. Use

, to scroll the highlight INSTALL, and then press .

3. Use

, to scroll the highlight CHANNEL SKIP, and then press .

4. Use [P UP] or [P DN] keys to view the programme in the list.

5. Select the programme you wish to skip or not skip using or keys. The skip

function will be toggled on or off.

RETURN TO TOP OF THE PAGE

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_ap.htm (5 of 6)6/30/2004 11:37:49 AM

Using other menus (AP)

file:///D|/My%20documents/dfu/B2C_TV_NAFTA/ENGLISH/170T4/osd/tv_ap.htm (6 of 6)6/30/2004 11:37:49 AM