Philips 157263 User Manual

Ceramalux®High Pressure Sodium Non-Cycling 1000 Watt ED-25 (Clear) Lamp

featuring ALTO®Lamp Technology

◗ Ordering Information

Ordering Code C1000S52/ALTO NC HPS ANSI Designation S52 Product Number 157263 Description High Pressure Sodium

TCLP*Compliant Non-Cycling

Package Quantity 6

◗ Physical Characteristics

Bulb Size ED-25 Bulb Finish Clear Base Mogul Screw Max. Overall Length (MOL) 15.08" (383mm) Light Center Length (LCL) 8.74" (222mm) Arc Length 8.5" (215mm) Arc Tube Length 9.6" (243mm) Arc Tube Material Aluminum Oxide Operating Position Universal Maximum Permissible Bulb Temperature 400ºC (752°F) Maximum Permissible Base Temperature 210ºC (410°F) Maximum Bulb to Base Eccentricity 3° Maximum Arc Tube to Base Eccentricity 3°

◗ Operating Characteristics (Photometric)

Approximate Initial Lumens Approximate Mean Lumen Rated Average Life, Hours Correlated ColorTemperature (CCT) 2100 K CIE Chromaticity Approximate x-.515, y-.420 Color Rendering Index (CRI) 20 Efficacy (LPW) 130

130,000 117,000 30,000

◗ Operating Position

Universal

◗ TCLP*Characteristics

Toxicity Characteristic Leaching Procedure (Federal TCLP) Results

Hg EPA Limit (mg/l) Max 0.200 5.00 C1000S52/ALTO NC HPS 0.062 <0.31

Mercury (mg/lamps) Max 11

Philips Lighting Company 200 Franklin Square Drive P.O. Box 6800 Somerset, NJ 08875-6800 1-800-555-0050

Division of Philips Electronics North America Corporation

pdated 1/07 TDS-157263

www.philips.com

Philips Lighting 281 Hillmount Road Markham, Ontario Canada L6C 2S3 1-800-555-0050

A Division of Philips Electronics Ltd.

Ceramalux®High Pressure Sodium Non-Cycling 1000 Watt ED-25 (Clear) Lamp featuring ALTO

lectrical Data

Lamp Watts (Nominal). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000

Lamp Operating Voltage (rms) (Nominal) . . . . . . . . . . . . . . . . . . 275V

Initial Lamp Voltage Range (rms). . . . . . . . . . . . . . . . . . . . . . . . . . 250–300V

Lamp Operating Current (Amps) (rms) (Nominal). . . . . . . . . . 4.7

Maximum Lamp Star ting Current (Amps)(rms) . . . . . . . . . . . . . 8.0

Lamp Current Crest Factor (Maximum) . . . . . . . . . . . . . . . . . . . 1.8

Warm-up Time to 80% of Output . . . . . . . . . . . . . . . . . . . . . . . . 7 Minutes

Re-strike Time for Hot Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Minutes

Ballast Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ANSI S52

Ballast Open Circuit Voltage (Minimum): . . . . . . . . . . . . . . . . . . 456 Vrms

Pulse Peak Volts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2675

Pulse Width @ 90% Peak. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 µs Minimum at 2700 Volts

Pulse Frequency (Minimum)

Lag Ballast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 per Cycle

Lead Circuit Ballast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 per Cycle

Minimum Operating Temperature. . . . . . . . . . . . . . . . . . . . . . . . . -30°C

Reference Ballast Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Ω (ohms) minimum at 480V

Maximum Lamp Watts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Minimum Lamp Watts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 750

Maximum Voltage Increase by Fixture . . . . . . . . . . . . . . . . . . . . . 25V

Footnotes:

1) Measured at 100 hours of life in ver tical and horizontal positions.

2) Approximate mean lumen output at 40% of lamp rated average life. Measured in ver tical and hor izontal oper ating positions. ) Rated average life is the life obtained, on the average, from large representative groups of lamps in laborator y tests under controlled conditions at 10 or more operating hours per start.

t is based on survival of at least 65% of the lamps and allows for individual lamps or groups of lamps to vary considerably from the average.

*The TCLP is the US EPA’sToxicity Characteristic Leaching Procedure.

WARNINGS, CAUTIONS AND OPERATING INSTRUCTIONS

for Ceramalux High Pressure Sodium Lamps

“WARNING:These lamps must be operated in ﬁxtures designed for use with

High Pressure Sodium lamps.The ﬁxture wattage rating must match the wattage indicated on the outer glass bulb. Do not scratch the outer bulb or subject it to pressure as this could cause the outer bulb to crack or shatter.A partial vacuum in the outer bulb may cause glass to ﬂy if the glass is struck. Operating the lamp improperly may result in

PERSONAL INJURY, PROPERTY DAMAGE, BURNS AND FIRE.

1) If the outer glass bulb is broken, shut off power immediately and remove the lamp

after it has cooled.

2) Use only auxiliary equipment meeting Philips and/or ANSI standards. Use within

voltage limits recommended by ballast manufacturer.

A. Operate lamp only within speciﬁed limits of operation. B. For total supply load refer to ballast manufacturers electrical data.

3) Protect lamp base, socket and wiring against moisture, corrosive atmospheres and

excessive heat.

4) Replace the lamp if the outer glass bulb has been scratched, cracked or damaged

in any way.

5) If a lamp bulb support is used, be sure to insulate the support electrically so as to

avoid possible decomposition of the bulb glass.

6) Do not use this lamp in a ﬁxture which redirects a substantial portion of the

energy toward the arc tube and its immediate vicinity, as this may lead to very early lamp failure.

7) Take care in handling and disposing of lamps. If arc tube is broken, avoid skin

contact with any of the contents or fragments.

8) The arc tube of this lamp contains sodium and mercury. Dispose of in accordance

with federal, state and local requirements.

Subject to change without notice)

(

Lamp Technology