Philips 151423 User Manual

◗ Ordering Information

Ordering Code CDM70/PAR30L/M/SP/4K
ANSI Designation M139/O
Product Number 151423

Description MasterColor

Ceramic Metal Halide

Package Quantity 6

◗ Physical Characteristics

Bulb Size PAR-30L
Bulb Finish Clear
Base Medium Screw
Max. Overall Length (MOL) 4 3/4" (121mm)
Light Center Length (LCL) N/A
Arc Length N/A
Arc Tube Material Polycrystalline Alumina
Max. Permissible Bulb Temp. 300º C (572ºF)
Max. Permissible Base Temp. 190º C (374º F)
Max. Lens-to-Reflector Rim Temp. 160º C (320º F)
Max. Bulb to Base Eccentricity 3º
Max.Arc Tube to Base Eccentricity 3º

◗ Operating Characteristics (Photometric)

Rated Initial Lumens

1

4300

Mean Lumens,Approx.

2

3010
MBCP (Max. Beam Candlepower) 63,000
Beam Angle (at 50% of MBCP) 10º
Rated Average Life, Hours

3

9000
Correlated Color Temp. (CCT)

4

4000K
CIE Chromaticity Approx.

4

x-.371, y-.366
Color Rendering Index (CRI) 94
Efficacy (lpw) 61

◗ Operating Position

Universal-Open or Enclosed PAR Style Luminaires

Note: Operate only on thermally protected electronic ballasts.

MasterColor®Ceramic Metal Halide
70 Watt PAR30L Spot 4K Lamp

with FadeBlock

™

4 3/4"

Electrical Data (Subject to change without notice)

Lamp Watts (Nominal) . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Lamp Operating Voltage (rms) (Nominal)

(4)

. . . . . . . . . . 88

Initial Lamp Voltage Range (rms)

(5)

. . . . . . . . . . . . . . . . . 75–100

Lamp Operating Current (Amps) (rms) (Nominal). . . . 0.83

Warm-up Time to 80% of Output . . . . . . . . . . . . . . . . . 2 Minutes

Re-strike Time for Hot Lamp . . . . . . . . . . . . . . . . . . . . . 4–8 Minutes

Ballast Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ANSI M139/O

Ballast Open Circuit Voltage (Minimum) . . . . . . . . . . . . 198

Pulse Peak Volts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000 Min.,4000 Max.

Pulse Width @ 90% Peak . . . . . . . . . . . . . . . . . . . . . . . . 2 Micro Second Minimum

Pulse Repetition Rate (Minimum). . . . . . . . . . . . . . . . . . 2 per Half Cycle

Minimum Operating Temperature. . . . . . . . . . . . . . . . . . -30ºC

MasterColor®Ceramic Metal Halide 70 Watt PAR30L Spot 4K Lamp with FadeBlock

™

Philips Lighting Company
200 Franklin Square Drive
P.O. Box 6800
Somerset, NJ 08875-6800
1-800-555-0050

A Division of Philips Electronics North America Corporation

Updated 04/06 TDS-151423

Philips Lighting
281 Hillmount Road
Markham, Ontario
Canada L6C 2S3
1-800-555-0050

A Division of Philips Electronics Ltd.

www.philips.com

1) Measured at 100 hrs. life. Approximate lumen values listed are for vertical operation of the lamp.

2) Approximate lumen output at 40% of lamp rated average life.

3) Rated average life is the life obtained, on the average, from large representative groups of lamps in laboratory tests under controlled conditions at 10 or more

operating hours per star t. It is based on survival of at least 50% of the lamps and allows for individual lamps or groups of lamps to vary considerably from the average.

4) Measured at rated lamp watts on a linear reactor. LPW does not include ballast losses.

5) Measured with the lamp operating at rated watts.

WARNINGS, CAUTIONS AND OPERATING INSTRUCTIONS

R

“WARNING: These lamps can cause serious skin burn and eye

inflammation from short wave ultraviolet radiation if outer envelope of the lamp
is broken or punctured. Do not use where people will remain for more than a few
minutes unless adequate shielding or other safety precautions are used. Certain lamps
that will automatically extinguish when the outer envelope is broken or punctured are
commercially available.”This lamp complies with FDA radiation performance standard
21 CFR subchapter J. (USA:21CFR 1040.30 Canada: SOR/DORS/80-381)

If the outer bulb is broken or punctured, turn off at once and replace the
lamp to avoid possible injury from hazardous short wave ultraviolet radiation.
Do not scratch the outer bulb or subject it to pressure as this could cause the
outer bulb to crack or shatter. A partial vacuum in the outer bulb may cause
glass to fly if the envelope is struck.

WARNING:The arc-tube of metal halide lamps are designed to operate under high

pressure and at temperatures up to 1000º C and can unexpectedly rupture due to
internal or external factors such as a ballast failure or misapplication.
If the arc-tube ruptures for any reason, the outer bulb may break and pieces of extremely
hot glass might be discharged into the surrounding environment. If such
a rupture were to happen, THERE IS A RISK OF PERSONAL INJURY,

PROPERTY DAMAGE, BURNS AND FIRE.These lamps are designed
to retain all the glass particles should an arc tube rupture occur. The following
operating instructions are recommended to minimize
these occurrences.

RELAMP FIXTURES AT OR BEFORE THE END OF RATED LIFE.Allowing
lamps to operate until they fail is not advised and may increase the possibility
of inner arc tube rupture.

This lamp contains an arc tube with a filling gas containing less than 10 nCi of
Kr-85 and is distributed by Philips Lighting Company, a division of Philips
Electronics North America Corporation, Somerset, New Jersey,08875.

CAUTION: TO REDUCE THE RISK OF PERSONAL INJURY, PROPERTY

DAMAGE, BURNS AND FIRE RESULTING FROM AN ARC-TUBE RUPTURE THE
FOLLOWING LAMP OPERA

TING INSTRUCTIONS MUST BE FOLLOWED:

LAMP OPERA

TING INSTRUCTIONS:

1. RELAMP FIXTURES AT OR BEFORE THE END OF RATED LIFE. Allowing lamps to operate
until they fail is not advised and may increase the possibility of inner arc tube rupture.

2. Before lamp installation/replacement, shut power off and allow lamp and fixture to cool
to avoid electrical shock and potential burn hazards.

3. Use only auxiliary equipment meeting Philips and/or ANSI standards. Use within voltage
limits recommended by ballast manufacturer.

A. Operate lamp only within specified limits of operation.

B. For total supply load refer to ballast manufacturers electrical data.

C. Operate Par 20 3000K and Par 30L 3000K lamps only

on thermally protected ballasts

D. Operate Par 20 4000K and Par 30L 4000K lamps only

on thermally protected electr

onic ballasts

4. Periodically inspect the outer envelope. Replace any lamps that show scratches,
cracks or damage.

5. If a lamp bulb support is used, be sure to insulate the suppor t electrically to
avoid possible decomposition of the bulb glass.

6. Protect lamp base, socket and wiring against moisture, corrosive atmospheres
and excessive heat.

7.Time should be allowed for lamps to stabilize in color when turned on for the
first time. This may require several hours of operation, with more than one start.
Lamp color is also subject to change under conditions of excess vibration or shock,
and color appearance may vary between individual lamps.

8. Lamps may require up to 10 minutes (4–8 minutes for CDM-R111) to re-light if there
is a power interruption.

9.Take care in handling and disposing of lamps. If an arc tube is broken, avoid skin contact
with any of the contents or fragments.

10. For proper installation and removal, lamp should be handled by the sides of the reflector

and not by the aluminum front anti-glare cap.