Philips 105S63, 105S69 User Manual

Philips_manual_

Tuesday, November 18, 2003 3:00:45 PM

Before operating the monitor please read this manual thoroughly. This manual should be retained for future reference.

Contents

Packing list ----------------------------------------------------

Precautions ----------------------------------------------------

Installation Instructions -------------------------------------

Swivel Base -------------------------------------------------Power cord -------------------------------------------------Video cable --------------------------------------------------

Operating Instructions --------------------------------------

General Instructions -------------------------------------Front panel control ---------------------------------------How to adjust a setting ----------------------------------Adjusting the picture -------------------------------------

Plug and play --------------------------------------------------

Technical Support (FAQ) -----------------------------------

Appendix A – Specifications ------------------------------Appendix B – Factory Preset Timing Table -----------Your International Guarantee -----------------------------

PACKING LIST

The product package should include the following items:

1. Monitor

2. Owner's Manual

3. Power Cord

4. Swivel Base

7-8

11-12

13 14

3 3 3 4

5 5 6 6

ENGLISH

Philips_manual_

Tuesday, November 18, 2003 3:00:45 PM

PRECAUTIONS

Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen

sink, laundry tub, swimming pool or in a wet basement.

Do not place the monitor on an unstable cart, stand, or table. If the

monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.

Slots and openings in the back and bottom of the cabinet are provided for

ventilation. To ensure reliable operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place

ENGLISH

the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.

The monitor should be operated only from the type of power source

indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.

The monitor is equipped with a three-pronged grounded plug, a plug with

a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the threewire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug.

Unplug the unit during a lightning storm or when it will not be used for

long periods of time. This will protect the monitor from damage due to power surges.

Do not overload power strips and extension cords. Overloading can result

in fire or electric shock.

Never push any object into the slot on the monitor cabinet. It could short

circuit parts causing a fire or electric shock. Never spill liquids on the monitor.

Do not attempt to service the monitor yourself; opening or removing

covers can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel.

To ensure satisfactory operation, use the monitor only with UL listed

computers which have appropriate configured receptacles marked between 100 - 240 VAC, Min. 1.5A.

The wall socket shall be installed near the equipment and shall be easily

accessible.

Philips_manual_

Tuesday, November 18, 2003 3:00:45 PM

INSTALLATION INSTRUCTIONS

Swivel Base

To attach the swivel base to the monitor, do the following:

• Carefully turn the monitor on its side or upside down. ( see figure 1 )

• Locate the cavities at the bottom front of the monitor.

• Insert the pegs on the swivel base into these cavities. Push the swivel base

forward until the swivel base locks in place.

• To remove the swivel base, hold the bottom of the swivel base, then push

it out.

Install Remove

ENGLISH

Figure 1 Installing and Removing the Swivel Base

Power Cord

Power Source:

1. Make sure the power cord is the correct type that required in your area.

2. This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area ( No user adjustment is required. )

3. Connect the power cord into your monitor’s power input socket, and then plug the other end into a 3-pin AC power outlet. The power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your monitor.

Philips_manual_

Tuesday, November 18, 2003 3:00:45 PM

Video cable

Connecting the Video Cable: The monitor comes with a built-in video cable.

Plug the signal cable's 15-pin connector into the computer's video port and tighten the two screws on the cable connector.

Caution:Don’t bend the signal cable, otherwise it will break the inner wire.

Connecting the Power Cord: Plug the power cord into the monitor's AC power socket. Then plug the power cord into a grounded AC outlet or ULapproved power strip or the power output socket on your PC.

Caution: If the AC outlet is not grounded (with three holes), install the

proper grounding adapter (not supplied).

ENGLISH

Figure 2 Connecting Cables

1. Power Cord 2. Signal Cable

Philips_manual_

Tuesday, November 18, 2003 3:00:46 PM

OPERATING INSTRUCTIONS General Instructions

The power switch is located at front panel of the monitor. Press the power switch to turn the monitor on or off. The other control knobs are located at the base of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences.

The power cord should be connected. Connect the video cable from the monitor to the video card. To turn the monitor on, press the POWER switch to ON position. The

power indicator will light up.

Your monitor features a unique quick switch system which provides a

picture within seconds after the monitor is switched on.

ENGLISH

Figure 3 External Control Knob

1. POWER SWITCH 4. CONTRAST/

2. POWER INDICATOR 5. BRIGHTNESS/

3. MENU 6. EXIT

Notes

Do not install the monitor in a location near heat sources such as

radiators or air ducts , or in a place subject to direct sunlight , or excessive dust or mechanical vibration or shock.

Save the original shipping carton and packing materials, as they will

come in handy if you ever have to ship your monitor.

For maximum protection, repackage your monitor as it was originally

packed at the factory.

To keep the monitor looking new, periodically clean it with a soft cloth.

Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety precaution, always unplug the monitor before cleaning it.

Philips_manual_

Tuesday, November 18, 2003 3:00:46 PM

Front Panel Control

Power Switch: Press this knob to switch ON/OFF of monitor’s power.

MENU Contrast

: Active OSD menu or function adjust confirm.

/ : Adiust contrast or function adjust.

Brightness / : Adjust brightness or function adjust. EXIT: Press the EXIT key to inactive OSD menu. Power Indicator:

Green — Power On mode.

Off mode.

ENGLISH

Orange —

How to adjust a setting

The monitor controls are accessed by pressing button MENU to enable OSD (On-Screen-Display). The main menu will be displayed as follows.

H: 31.4KHz V: 70.0Hz

Contrast

Note: If adjustment or selection of any OSD menu is not made for more

than 10 seconds, the current setup will be saved and the OSD will disappear automatically.

Philips_manual_

Tuesday, November 18, 2003 3:00:46 PM

100

9300

6500

720 × 400

Figure 4 The OSD Message

Adjusting the picture

The description for functional control icons

1. Contrast : Adjust the picture contrast.

2. Brightness

Adjust the picture brightness.

3. H-center Adjust the horizontal position of the picture.

4. H-size Adjust the picture’s horizontal size.

5. V-center

Adjust the vertical position of the picture.

6. V-size :

ENGLISH

Adjust the picture’s vertical size.

7. Zoom

Adjust the picture’s horizontal and vertical size simultaneously.

8. Pincushion

Adjust the pincushion and barrel.

9. Trapezoid

Adjust the picture’s trapezoid distortion.

10. Pin-Balance

Adjust to compensate the pincushion unbalance.

11. Parallelogram

Adjust the picture to be a rectangle.

12. Rotation

Adjust the picture tilt to horizontal position.

13. Recall 6500°k/9300°k color Temperature : The color temperature for 6500°K is x=0.313, y=0.329 and 9300°K is x=0.283, y=0.297. It presents two different color sets on the screen. You can select 9300°K or 6500°K by pressing MENU Key.

Philips_manual_

Tuesday, November 18, 2003 3:00:46 PM

14. User color

If the 9300°K normal white or 6500°K warmer white do not satisfy your desire, properly adjust R . B GAIN controls to obtain your optimum whiteness level.

15. Degauss

If color impurity occurs when moving or swiveling the monitor, press MENU Key and degauss to fix the picture condition.

16. H-Moire Reduce/Moire Disable/V-Moire Reduce/Quit Moire is the result of interference between the phosphor layout and

the video signal. In some cases, you may find the moire very noticeable. Press the MENU to enter in the moire reduce setting.

ENGLISH

Please adjust the level to the optimum condition. Note: Too high of a setting will cause the picture to shake.

17. Recall Press RECALL to restore the monitor to factory settings.

18. Exit

Close OSD window.

19. Select language

Select the language as you like.

Philips_manual_

Tuesday, November 18, 2003 3:00:46 PM

THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.

This monitor meets the Power Management standards as set by the Video Electronics Standards Association (VESA) and/or the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees ( NUTEK ). This feature is designed to conserve electrical energy by reducing power consumption when there is no video input signal present. When there is no video input signal this monitor, following a time-out period, will automatically switch to an OFF mode. This reduces the monitor's internal power supply consumption. After the video input signal is restored, full power is restored and the display is automatically redrawn. The appearance is similar to a "Screen Saver" feature except the display is completely off. The display is restored by pressing a key on the keyboard, or clicking the mouse.

Plug and play

Plug & Play DDC1/2B Feature

This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the mon itor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels, DDC1 and DDC2B. The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel.

Video Cable Pin Assignments:

1. Red 5. Ground 9. NC 13. H-sync

ENGLISH

2. Green 6. R-Ground 10. Ground 14. V- sync / * VCLK

3. Blue 7. G-Ground 11. Monitor Ground 15. DDC-Serial Clock

4. Ground 8. B-Ground 12. DDC-Serial Data * FOR DDC

Philips_manual_

Tuesday, November 18, 2003 3:00:46 PM

TECHNICAL SUPPORT (FAQ)

Problem & Question Possible Solution Power LED is not on *Check if the Power Switch is in the ON

position

*Power Cord should be connected

No Plug & Play *Check if the PC system is Plug & Play

compatible

*Check if the Video Card is Plug & Play

compatible

*Check if the D-15 plug pin of Video

Cable is bent

ENGLISH

Picture is fuzzy *Adjust the Contrast and Brightness

Picture bounces or a wave pattern is present in the picture

The power LED is ON (orange) but there’s no video

or no picture

Missing one of the primary colors (RED, GREEN, or BLUE)

*Make sure the Monitor Drivers are

installed

Controls.

*Move electrical devices that may cause

electrical interference.

*Computer Power Switch should be in the

ON position

*Computer Video Card should be snugly

seated in its slot

*Make sure monitor’s video cable is

properly connected to the computer.

*Inspect monitor’s video cable and make

sure none of the pins are bent.

*Make sure computer is operational by

hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key.

*Inspect the monitor’s video cable and

make sure that none of the pins are bent.

Philips_manual_

Tuesday, November 18, 2003 3:00:46 PM

APPENDIX A - SPECIFICATIONS

CRT(Picture Tube) 38cm(15"), 90º deflection, 29mm neck,

0.28mm dot pitch glare screen. Viewable Image Size 35.6cm (14"), diagonal Display Color

Analog input Unlimited colors

Input Signal All timing that meets scanning frequencies

Specification

Video Analog R, G, B 0.7Vpp positive/75 ohm Sync.

Synchronization

Horizontal 30kHz to 54kHz automatically

Vertical 50Hz to 120Hz automatically Max. Resolution 1024×768 Video bandwidth 72MHz Factory Preset Timings : 6 User mode Timings : 9 Misconvergence

Center 0.3mm Max.

Corner 0.4mm Max. Power Source Switching mode power supply

Operating 0°C to 40°C ambient Humidity 10% to 85% relative, non-condensing Weight 11.5kg(Net) Dimensions

Monitor 360(W) × 362(H) × 387(D)mm Signal Cable 15 pin mini D-Sub

Horizontal sync. : Positive/Negative Vertical sync. : Positive/Negative

AC 100-240V, 50Hz/60Hz full range

ENGLISH

External Controls: Switch POWER SWITCH

Philips_manual_

Tuesday, November 18, 2003 3:00:46 PM

MENU KEY CONTRAST/UP KEY

BRIGHTNESS/DOWM KEY EXIT KEY

Functions ( OSD ) Contrast Brightness H-center H-size V-center V-size Zoom Pincushion Trapezoid Pin-Balance Parallelogram Rotation

ENGLISH

6500°k User color 9300°k Degauss Moire Recall Exit Select language Plug & Play DDC1/2B EPA ENERGY

STAR

On mode Off mode

62W

5W Power consumption 62W Max. Preset display area 270mm × 202mm

UL, CSA, FCC, CERegulations

Philips_manual_

Tuesday, November 18, 2003 3:00:46 PM

APPENDIX B - FACTORY PRESET TIMING TABLE

STANDARD RESOLUTION

HORIZONTAL

FREQUENCY

IBM 720×400 31.5kHz 70Hz

VGA 640×480 31.5kHz 60Hz

VESA/85 640×480 37.5kHz 75Hz

VESA/85 800×600 46.9kHz 75Hz

VESA/85 800×600 53.6kHz 85Hz

VESA/60 1024×768 48.4kHz 60Hz

VERTICAL

FREQUENCY

ENGLISH

Philips_manual_

Tuesday, November 18, 2003 3:00:46 PM

+ 32 hidden pages