Philips 10000241 Owner's Manual

Saeco International Group S.p.A .

Via Torretta, 240 I-40041 Gaggio Montano, Bologna Tel: + 39 0534 77 1111

Fax: + 39 0534 31025 ww w.saeco.com

The manu fa cture r r eser ves th e right t o c hange th e f eat ur es of t he produ ct wi th out pr io r n otice.

Le pro du cteur se réser ve le droit d“ appor te r t outes mo di ficat io ns sans p ré avi s.

Type SUP-032NR Cod.15001365 Rev.00 del 15-09-07

Operation and maintenance manual

Before using the machine, please read the attached operating instructions.

Carefully read the safety rules.

Mode d'emploi

Veuillez lire attentivement le mode d'emploi

(notamment les consignes de sécurité) avant d'utiliser l'appareil.

FOR HOUSEHOLD USE ONLY

USAGE DOMESTIQUE SEULEMENT

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, including the following:

1. Read all instructions.

2. Do not touch hot surfaces. Use handles or knobs.

3. To protect against fire, electric shock and injury to persons do not

immerse cord, plugs, or appliance in water or other liquid.

4. Close supervision is necessary when the appliance is used by or near children.

5. Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts, and before cleaning the appliance.

6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment.

7. The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock or injury to persons.

8. Do not use outdoors.

9. Do not let cord hang over edge of table or counter, or touch hot

surfaces.

10. Do not place on or near a hot gas or electric burner, or in a heated oven.

11. Always attach plug to appliance first, then plug cord into wall outlet. To disconnect, turn any control to “off”, then remove plug from wall outlet.

12. Do not use appliance for other than intended use.

13. Save these instructions.

SAVE THESE INSTRUCTIONS

CAUTION

This appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service center. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no parts inside the machine serviceable by the user. Repair should be done by authorized service personnel only.

1 Check voltage to be sure that the voltage indicated on the nameplate

corresponds with your voltage.

2 Never use warm or hot water to fill the water tank. Use cold water only. 3 Keep your hands and the cord away from hot parts of the appliance during

operation.

4 Never clean with scrubbing powders or harsh cleaners. Simply use a soft

cloth dampened with water.

5 For optimal taste of your coffee, use purified or bottled water. Periodic

descaling is still recommended every 2-3 months.

6 Do not use flavored or caramelized coffee.

INSTRUCTIONS FOR THE POWER

SUPPLY CORD

A. A short power-supply cord (or detachable power-supply cord) is to be

provided to reduce risks resulting from becoming entangled in or tripping over a longer cord.

B. Longer detachable power-supply cords or extension cords are available

and may used if care is exercised in their use.

C. If a long detachable power-supply cord or extension cord is used,

1. The marker electrical rating of the detachable power-supply cord or extension

cord should be at least as great as the electrical rating of the appliance

2. If the appliance is of the grounded type, the extension cord should be a grounding-type 3-wire cord, and

3. The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over.

CONTENTS

GENERAL INFORMATION ...................................................................................................................3

TECHNICAL DATA ...............................................................................................................................3

APPLIANCE .........................................................................................................................................4

ACCESSORIES ......................................................................................................................................................4

INSTALLATION .................................................................................................................................... 5

STARTING THE MACHINE .........................................................................................................................................5

SETTING THE LANGUAGE.........................................................................................................................................6

MEASURING THE WATER HARDNESS ...........................................................................................................................6

INSTALLING THE INTENZA WATER FILTER .....................................................................................................................7

DISPLAY ..............................................................................................................................................8

AROMA OPTI-DOSE (ADJUSTS THE COFFEE DOSE PER CUP) ............................................................................................8

ADJUSTMENTS ...................................................................................................................................9

COFFEE INTENSITY ................................................................................................................................................9

ADJUSTING THE HEIGHT OF THE DRIP TRAY .................................................................................................................9

COFFEE GRINDER ADJUSTMENT ................................................................................................................................9

BEVERAGE DISPENSING ................................................................................................................. 10

ESPRESSO / COFFEE / LONG COFFEE ......................................................................................................................10

DISPENSING BEVERAGES WITH GROUND COFFEE ........................................................................................................ 11

HOT WATER DISPENSING .......................................................................................................................................12

DISPENSING STEAM .............................................................................................................................................13

MAKING CAPPUCCINO ...........................................................................................................................................14

MILK ISLAND (OPTIONAL) ......................................................................................................................................15

BEVERAGE SETTINGS ..................................................................................................................... 16

1. QUICK PROGRAMMING ......................................................................................................................................16

PROGRAMMING FROM THE “BEVERAGE SETTINGS” MENU ..........................................................................................16

PROGRAMMING THE MACHINE .......................................................................................................18

MACHINE SETTINGS .............................................................................................................................................19

LANGUAGE MENU

HARDNESS MENU

WATER

ALARM MENU

ACOUSTIC

ALARM MENU

FILTER

RINSE

MAINTENANCE...................................................................................................................................20

WATER FILTER MENU

DESCALING

GROUP WASHING

BREW

ENERGY

SAVING .................................................................................................................................................21

SPECIAL FUNCTIONS ............................................................................................................................................21

MAINTENANCE .................................................................................................................................22

DESCALING CYCLE ..............................................................................................................................................22

GROUP WASHING ................................................................................................................................................24

CLEANING AND MAINTENANCE ......................................................................................................25

MAINTENANCE DURING OPERATION ..........................................................................................................................25

GENERAL MACHINE CLEANING ................................................................................................................................25

CLEANING THE BREW GROUP. ................................................................................................................................26

ERROR CODES .................................................................................................................................27

TROUBLESHOOTING ........................................................................................................................28

SAFETY RULES .................................................................................................................................29

GENERAL INFORMATION - TECHNICAL DATA

GENERAL INFORMATION

This coffee machine is suitable for preparing espresso coffee using coffee beans, and it is equipped with a device to dispense steam and hot water. The machine is designed for domestic use only, and is not suitable for heavy or professional use.

Warning: no liability is assumed for any damage caused by:

• incorrect use not in accordance with the intended uses;

• repairs not carried out by authorized customer service centres;

• tampering with the power cord;

• tampering with any part of the machine;

• the use of non-original spare parts and accessories;

• failure to descale the machine or use at temperatures below 0°C (32°F).

IN THESE CASES, THE WARRANTY IS NOT VALID.

THE WARNING TRIANGLE IND ICATES ALL IMPORTANT INSTRUCTIONS FOR THE USER’S SAFETY. PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY TO PREVENT SERIOUS I NJURIES!

HOW TO USE THESE OPERATING INSTRUCTIONS.

Keep these operating instructions in a safe place and make them available to anyone else who may use the coffee machine. For further information or in case of problems, please refer to an authorized service centre. For Saeco customer service, call 1-800-933-7876 in the U.S., or 1-514-385-5551 in Canada.

TECHNICAL DATA

Nominal voltage Power rating Power supply Shell material Size (w x h x d) Weight Cable length Control panel Water tank Coffee bean hopper capacity Pump pressure Boiler Coffee grinder Quantity of ground coffee Grounds drawer capacity Safety devices

Subject to engineering and manufacturing changes due to technological developments.

See label on the appliance See label on the appliance See label on the appliance ABS - Thermoplastic 313 x 372 x 408 mm - 12.60 x 14.57 x 15.75 in 9 Kg - 19.8 lbs 1200 mm - 47.24 in Front (display 2x16 characters)

1.7 liters - 57.5 oz (removable) 250 grams - 8.9 oz of coffee beans 15 bar Stainless steel Ceramic 7 - 10.5 grams / 0.25 - 0.37 oz. 14 portions Boiler pressure safety valve – Double safety thermostat.

APPLIANCE

Cup stacking surface

Control panel

SBS dial

Dispensing head

Coffee bean hopper

Coffee bean lid

Compartment for preground coffee

Power button

Service door

Coffee grounds drawer

Hot water / steam knob

“Milk Island” connection

Water tank

ACCESSORIES

Intenza water ﬁ lter

Drip tray + grill and ﬂ oat

Hot water / steam spout

Ground coffee

measuring scoop

Brew Group

Drip tray

Socket for power cord

Water hardness test strip

Grinder adjustment key Power cord

Lubricant for the

brew group

INSTALLATION

STARTING THE MACHINE

Make sure that the main power button is not pressed in the “ON” position.

1 2 3

Remove the coffee bean lid. Fill the hopper with coffee beans.

Fill the tank with fresh drinking water. Do not exceed the “max” level indicated on the water tank. Once ﬁ lled, place the tank back into the machine.

Close the lid pushing it down completely.

Attach the female end of the power cord to the machine. Insert the male end into the power outlet (see data tag).

The machine automatically primes the water circuit. The machine is now ready for use. Water may not be dispensed into the container. This should not be considered a malfunction.

Remove the water tank. Install the water ﬁ lter as recommended on page 7.

Place a container beneath the hot water spout.

Press the main power button to the “ON” position.

INSTALLATION

SETTING THE LANGUAGE

When the machine is switched on for the ﬁ rst time, it requires the selection of the desired language. This allows you to adjust the parameters of the beverages to the typical parameters of the country where the machine is used. This is why some languages are differentiated also by country.

1 2

2.1 language English

Select the desired language by navigating the click wheel with

When the desired language is displayed, press

your ﬁ nger.

4 5 6

warming up

Wait until the machine completes the warming phase.

Once the warming phase is completed, a small quantity of

rinse cycle please wait

water is dispensed. Wait for this rinsing to be completed automatically. Refer to page 19 to enable/disable the rinsing function.

self-diagnosis

The machine starts and displays all the messages in the selected language.

medium aroma

espresso

The screen for beverage dispensing appears on the display.

MEASURING THE WATER HARDNESS

The water hardness test strip is for one-time-use only.

Immerse the water hardness test strip in water for 1 second.

Intenza Aroma System

1234

Machine water hardness setting

Check the water hardness value and set:

- the machine water hardness level (page 19);

- the Intenza Aroma system (page 7).

INTENZA WATER FILTER

To improve the quality of the water you use, and to extend the life of your machine at the same time, it is recommended that you install the water ﬁ lter. After installation, select the water ﬁ lter function under the maintenance menu (see page 20). By setting the water ﬁ lter status to ON, the machine informs the user when the ﬁ lter must be replaced.

Remove the water ﬁ lter from its packaging, immerse it vertically (with the opening facing upwards) in cold water and gently press its sides so as to let the air bubbles out.

Remove the small white ﬁ lter from the water tank and store it in a dry place sheltered from dust.

Set the Intenza Aroma System: A = Soft water B = Medium water (standard) C = Hard water

4 5

Fill the water tank with fresh drinking water and re-insertit into

Place a container beneath the steam/hot water spout.

the machine.

7 8 9

3.1 filter 3.1.3 activate execute now

Scroll to “ﬁ lter” and press again.

Select “activate” and press the

button.

Insert the ﬁ lter in its place within the empty tank (see ﬁ gure); Press down until it clicks into place.

3 maintenance

Press

Select “maintenance” and press the

button.

Turn the knob to the position. Water dispensing begins.

When the machine has ﬁ nished, turn the knob until it is in the rest position ( ). Press a few times until the “exit” message is displayed. Then press

. The machine is now ready for use. NOTE: if the Intenza water ﬁ lter

is not used, insert the small white ﬁ lter previously removed (see step 1) into the water tank.

DISPLAY

Access the

programming menu

Click wheel

Select the coffee bean

dose or the quantity of

pre-ground coffee

• Press the button twice to make 2 cups. This operation can be performed up until the grinding of the ﬁ rst cup is complete.

selected espresso

• To brew 2 cups, the machine dispenses the ﬁ rst coffee and brieﬂ y interrupts dispensing in order to grind the second serving of coffee.

Coffee dispensing is then restarted and completed.

strong aroma

espresso

Press twice

Steam button

Conﬁ rmation button

Hot water button

selected

double espresso

AROMA OPTI-DOSE (ADJUSTS THE COFFEE DOSE PER CUP)

It is possible to choose three aroma options (strong, medium and mild) by pressing the button. These indicate the quantity of coffee the machine grinds for each beverage. This button is also used to select the pre-ground coffee function.

strong aroma

espresso

medium aroma

espresso

mild aroma

espresso

SELECT THE AMOUNT OF COFFEE TO BE GROUND BEFORE DISPENSING

pre-ground

espresso

THE BEVER AGE.

Coffee is a natural product and its features may change according to its origin and blend. The Saeco coffee machine is equipped with a self-adjusting system that allows you to use all types of coffee beans available on the market (except caramelized ones). The machine setting is performed automatically so as to ensure that the quantity of ground coffee is in line with the selected aroma, regardless of the coffee used.

ADJUSTMENTS

COFFEE INTENSITY

The SBS system has been carefully designed to give your coffee the intense taste you desire. Simply turn the dial and you will notice that the coffee goes from mild intensity to strong intensity.

SBS – SAECO BREWING SYSTEM

SBS adjusts the intensity and strength of the brewed coffee. The coffee may even be adjusted while brewing. This adjustment has an immediate effect on the selected type of brewing.

MILD

COFFEE

MEDIUM

COFFEE

ADJUSTING THE HEIGHT OF THE DRIP TRAY

Adjust the drip tray to the appropriate cup size before selecting the beverage. Height-adjustable drip tray:

To adjust the drip tray, lift it or lower it manually until it reaches the desired height.

Note: There is a red ﬂ oat in the drip tray to warn when it is necessary to empty the tray.

COFFEE GRINDER ADJUSTMENT

The machine enables a slight adjustment of the coffee grinder. Coffee may be ground according to your own tastes.

STRONG COFFEE

The adjustment must be performed by means of the pin located inside the coffee bean hopper. This must be pressed down and turned using the supplied key only. Press and turn the pin one notch at a time. You must brew 2-3 coffees before you will taste a difference.

The references located inside the bean hopper indicate the grind setting.

FINE GRINDMEDIUM GRINDCOARSE GRIND

BEVERAGE DISPENSING

COFFEE BREWIN G CAN BE STOPPED AT ANY TIME BY PRESSING TH E BUTTON AGAIN.

THE STEAM SPOUT M AY REACH HIGH TEMPER ATURES: DANGER OF SCALDING. DO NOT TOUCH IT W ITH BARE H ANDS.

Check that all the containers are clean. To carry out this operation, follow the instructions in the “Cleaning and Maintenance” section (see page 25).

To brew 2 cups, the machine dispenses the ﬁ rst coffee and brieﬂ y stops dispensing in order to grind the second serving of coffee. Coffee dispensing is then restarted and completed.

ESPRESSO / COFFEE / LONG COFFEE

This procedure shows how to brew an espresso. To brew another type of coffee, select it by navigating the click wheel with your ﬁ nger. Use appropriate espresso or coffee cups so that the coffee will not overﬂ ow.

1 2

Position 1 - 2 cup(s) to brew an espresso

Position 1 - 2 cup(s) to brew a coffee or a long coffee

strong aroma

espresso

Select the desired beverage by navigating the click wheel with your ﬁ nger.

4 5

strong aroma

espresso

If desired, select the quantity of coffee to be ground by pressing the

button one or more

times.

Press the cup and twice for 2 cups. The machine begins dispensing the selected beverage.

strong aroma

espresso

button: once for 1

The machine ﬁ nishes dispensing automatically based on the quantity determined by the manufacturer. It is possible to customize this quantity (see page 16).

DISPENSING BEVERAGES WITH GROUND COFFEE

The machine allows you to use pre-ground and decaffeinated coffee. Pre-ground coffee must be scooped into the appropriate compartment positioned next to the coffee bean hopper. Only use coffee that is ground speciﬁ cally for espresso machines and never coffee beans or instant coffee.

WARNING: ONLY PUT PRE-GROUND COFFEE INTO THE COMPARTMENT WHEN YOU WI SH TO BREW THIS TYPE OF B EVERAGE.

ONLY INSERT ONE SCOOP OF GROUND COFFE E AT A TIME. TWO CUPS OF COFFEE CANNOT BE BREWED SIMULTANEOUSLY WITH THIS FEATURE.

The preparation of an espresso using pre-ground coffee is shown in the example given below. The customized option of using pre-ground coffee is shown on the display.

1 2

strong aroma

espresso

pre-ground

espresso

insert gr.coffee

and press ok

Select the desired beverage by navigating the click wheel with your ﬁ nger.

Select the function by pressing the

button until the pre-ground

option appears. Press the

A message reminds the user to insert ground coffee into the appropriate compartment.

button to conﬁ rm.

Pour one scoop of ground coffee into the appropriate compartment using the measuring scoop

Press the brewing.

brewing

please wait

button to start

provided.

Note:

• If brewing does not start within 30 seconds from the appearance of the message (3), the machine will return to the main menu and discharge any pre-ground coffee into the grounds drawer;

• If no pre-ground coffee is poured into the compartment, only water will be dispensed;

• If the dose is excessive or if 2 or more scoops of coffee are inserted, the machine will not brew the beverage, and the coffee in the compartment will be discharged into the grounds drawer.

BEVERAGE DISPENSING

HOT WATER DISPENSING

DISPENS ING MAY BE PRECEDED BY SHOR T SPURTS OF HOT WATER AND SCALDING IS POSSIBLE. THE HOT WATER/STEAM SPOUT MAY REACH HIGH TEMPERATURES: DO NOT TOUCH IT WITH BARE HANDS. USE THE APPROPRI ATE HANDLE ONLY.

1 2 3

selected

hot water

Place a container beneath the steam/hot water spout.

brewing

hot water

The display shows “brewing... hot water”.

To dispense another cup of hot water, repeat this operation.

Press the button.

Wait until the machine has dispensed the desired quantity of water.

Turn the knob to the position.

When the machine has dispensed the desired quantity, turn the knob until it is in the rest position (

DISPENSING STEAM

DISPENS ING MAY BE PRECEDED BY SHOR T SPURTS OF HOT WATER AND SCALDING IS POSSI BLE. THE HOT WATER/STEAM SPOUT M AY REACH HIGH TEMPERATURES: DO NOT TOUCH IT W ITH BARE HAND S. USE THE APPROPRIATE HANDLE ONLY.

1 2 3

selected

steam

Place a container with the beverage to be warmed up beneath the steam spout.

brewing

steam

The display shows “brewing... steam”

Repeat the operation to heat another beverage.

Press the button.

5 6

Heat the beverage by gently swirling the container while steam is dispensed.

Turn the knob to the position.

When you have ﬁ nished, turn the knob until it is in the rest position (

After dispensing steam, clean the steam spout as described on page 25.

BEVERAGE DISPENSING

MAKING CAPPUCCINO

selected

steam

Fill 1/3 of the cup with cold milk.

Press the button.

4 5 6

Turn the knob to the position.

Froth the milk by gently swirling the cup.

strong aroma

espresso

Immerse the steam spout in the milk.

When you have ﬁ nished, turn the knob until it is in the rest position (

Place the cup beneath the dispensing head.

After dispensing, clean the steam spout as described on page 25. To brew 2 cappuccinos:

• froth two cups of milk by following step 1 to 6;

• brew two coffees by following steps 7 and 8 (in this case, press the

Press the button once: coffee dispensing begins.

button twice).

MILK ISLAND (OPTIONAL)

This device, which may be purchased separately, enables you to easily and comfortably prepare delicious cappuccinos.

Warning: before using the Milk Island, read the manual and all precautions carefully for correct use.

Important note: the quantity of milk in the carafe must never be below the “MIN” minimum level nor exceed the “MAX” maximum level. Thoroughly

clean all the Milk Island components after use.

To guarantee best results when preparing cappuccino, we recommend using cold (0-8°C / 32-45°F), partially skimmed milk.

1 2 3

Type MKI001

Milk Island - 04

Type MKI002

Milk Island - 08

Fill the milk carafe with the quantity of milk desired (between the MIN and MAX levels indicated).

Wait for the milk to be frothed.

6 7 8

Remove the carafe using the handle.

Place the milk carafe onto the base of the Milk Island. Check that the light on the base is green.

The machine will stop automatically after steaming continuously for 2 minutes. To dispense more steam turn the knob to the ( back to the

Gently swirl the carafe and pour the milk into the cup.

) position and then

position.

Turn the knob to the position.

When the desired quantity of froth has been reached, turn the knob until it is in the rest position (

Position the cup with frothed milk under the dispensing head. Brew coffee into the cup.

BEVERAGE SETTINGS

Every beverage can be programmed according to your individual tastes.

1. QUICK PROGRAMMING

You can program the quantity of coffee that will dispense into the cups when any beverage is selected. Select the type of beverage you want to program, then press and hold the (for example):

programming

espresso

The machine dispenses coffee. When the desired amount is reached, press the The display shows:

The dispensed quantity of coffee is memorized and replaces any previous settings.

saved

espresso

button again.

button until the display shows

2. PROGRAMMING FROM THE “BEVERAGE SETTINGS” MENU

To adjust the settings for preparing beverages: press the button and select “bev. settings” by navigating the click wheel with your ﬁ nger.

In this phase you can:

exit the programming mode

(see page 18)

by navigating the click wheel with

your ﬁ nger you can change the

settings for:

- the quantity of coffee to brew;

- the coffee temperature;

- coffee prebrewing.

- select the quantity of coffee to be ground (opti-dose)

The following page describes how to program coffee beverages; the programmable settings for each beverage may differ depending on the type of beverage.

1 bev. settings

adjust the settings for:

- the coffee temperature;

- coffee prebrewing.

restore factory settings

save the new settings

1 2 3

strong aroma

espresso

1 bev. settings

Check that the water tank and coffee

Press the button. bean hopper are full; place the cup under the dispensing head.

4 5

1.1 espresso

When the settings are changed, the message on the

display starts ﬂ ashing. When the changes are saved the message stops ﬂ ashing.

Select the beverage to program. Press the

button to conﬁ rm.

6 7

temp.: medium

espresso

Change the coffee quantity by navigating the click wheel with your ﬁ nger; conﬁ rm with

Press the

than two seconds to access the

other programmable settings.

button for more

9 10

prebrew: normal

espresso

prebrew: normal

espresso

Select “bev. settings”. Press the

button to conﬁ rm.

medium aroma

espresso

Press the

button a few times to adjust the quantity of coffee to be ground or select the use of preground coffee. Press the button to save.

temp.: medium

espresso

Change the temperature setting (high, medium, low) by navigating the click wheel with your ﬁ nger. Press the

button to save.

Prebrewing: the grounds are slightly dampened before brewing to bring out the full aroma of the coffee and enhance the ﬂ avor.

Press the prebrew setting.

button to select the

Change the prebrew value (normal, long, off) by turning the click wheel with your ﬁ nger. Press the

button to save.

Press the button to exit.

PROGRAMMING THE MACHINE

Some of the machine’s functions can be programmed according to your individual preferences.

1 bev. settings

1 Press the button. 2 Navigate the click wheel with your ﬁ nger to:

Press the

- conﬁ rm the selection;

- save the new settings.

1 bev. settings

2 mach. settings

3 maintenance

4 energy saving

5 special funct.

- select the functions

- change the function settings. button to:

Beverage settings (see page 16)

Machine settings (see page 19)

Maintenance settings (see page 20)

Energy saving (see page 21)

Special functions (see page 21)

To exit the programming mode:

exit

+ 47 hidden pages