PAN05-1A/-2A/-3A In Wall Single relay (1 way) switch
module
P
based on Z-Wave Plus technology, and it is fully compatible with any Z-WaveTM
enabled network. Mini size design let the module can easily hide itself into the wall
box and that will be good for the house decoration. Since PAN05 supports Security
Command Class, it can learn with Secured controller. Its functionality and supported
command classes is identical when included as a secure and non-secure device.
There are many kind of application by using the module to switch Load On and Off,
one main application is the light control. If connect the COM terminal directly to AC
Line terminal, the new smart relay calibration technology can reduce the inrush
current caused by the load and let the module work perfectly with many kind of light
Fig 1. Assembling
This in-wall switch module is a transceiver which is a security enabled device which
like incandescent, fluorescent and LED light. This module can also connect to
alternative power supply like DC 12V to switch on/off 12V MR-16 light as follow
picture.
Adding to Z-WaveTM Network
In the front casing, there is an on/off button with LED indicator below which is used to
toggle switch on and off or carries out inclusion, exclusion, reset or association.
When first power applied, its LED flashes on and off alternately and repeatedly at 0.5
second intervals. It implies that it has not been assigned a node ID and start auto
inclusion.
Auto Inclusion
The function of auto inclusion will be executed as long as the in wall switch does not
have Node ID and just connect the switch to main power.
1
Note: Auto inclusion timeout is 2 minute during which the node information of
explorer frame will be emitted once every several seconds. Unlike “inclusion” function
as shown in the table below, the execution of auto inclusion is free from pressing the
On/Off button on the Switch.
The table below lists an operation summary of basic Z-Wave functions. Please refer
to the instructions for your Z-WaveTM Certificated Primary Controller to access the
Association
1. The PAN05 is an always listening
Z-Wave device, so associations
may be added or removed by a
controller at any time.
Or If your controller requires to have
the PAN05 send a 'node information
frame' or NIF for associations, then
pressing the On/Off button three
times within 2 seconds will cause
the PAN05 to send its NIF.
2. There are only one group for the
switch
Setup function, and to include/exclude/associate devices
Function Description Annotation
No node ID The Z-Wave Controller does not allocate
a node ID to the Switch.
Inclusion
Exclusion
Reset 1. Pressing Include button of PAN05
1. Put your Z-Wave controller into
inclusion mode by following the
instructions provided by the
controller manufacturer.
2. Pressing Include button of PAN05
three times within 2 seconds will
enter inclusion mode.
1. Put your Z-Wave controller into
exclusion mode by following the
instructions provided by the
controller manufacturer.
1. Pressing Include button of PAN05
three times within 2 seconds will
enter exclusion mode.
Node ID has been excluded.
three times within 2 seconds will
enter inclusion mode.
2. Within 1 second, press Include
button of PAN05 again for 5
seconds.
3. IDs are excluded.
LED 2-second on, 2-second
off
One press one flash LED
One press one flash LED
0.5s On, 0.5s Off (Enter
auto inclusion)
Use this procedure only in
the event that the primary
controller is lost or
otherwise inoperable.
0.5s On, 0.5s Off (Enter
auto inclusion)
Including a node ID allocated by Z-Wave Controller means inclusion. Excluding a node
ID allocated by Z-Wave Controller means exclusion.
Failed or success in including/excluding the node ID can be viewed from the Z-Wave
Controller.
Sometimes people are not easy to execute exclusion or inclusion especially when
PAN05 already installed in a wall box. To solve this issue, PAN05 support a special
feature that can use S1 or S2 to execute “exclusion, inclusion, Reset or Association”
at the first 3 minutes when first time connect to main power.
LED Indication
To distinguish what mode the switch is in, view from the LED for identification.
State Type LED Indication
Normal Whenever we switch On and off of the PAN05 by S1 S2 or On/Off
No node ID Under normal operation, when the Switch has not been allocated a
Learning When PAN05 is in learning mode, LED flashes on and off
Overload When overload state occurs, the Switch is disabled of which LED
button or RF command, the LED will lights up when switch on;
whereas LED off when switch off.
node ID, the LED flashes on and off alternately at 2-second
intervals. By pressing S1 S2 or On/Off button, it will stop flashing
temporarily.
alternately and repeatedly at 0.5 second intervals.
flashes on and off alternately at 0.2 second intervals. Overload
state can be cleared by disconnect and reconnect the Switch to the
main power.
2
Choosing a Suitable Location
1. Do not locate the Switch facing direct sunlight, humid or dusty place.
2. The suitable ambient temperature for the Switch is 0°C~40°C.
3. Do not locate the Switch where exists combustible substances or any source of
heat, e.g. fires, radiators, boiler etc.
4.
After putting it into use, the body of Switch will become a little bit hot of which
phenomenon is normal.
Installation
1. Put the in wall switch into a wall box and connect the AC power wire L, N to
PAN05 connector L, N.
2. Connect the wall switch to the PAN05 as Fig1.
3. There are 3 mode PAN05 can be configured to match different kind of wall switch,
please refer to 3-1 Edge / Pulse / Edge-Toggle mode which described in next
section of this user manual.
4. If Edge-Toggle mode has been set, and the S1 S2 is connect to normal bi-stable
switch, every time when change the state of the wall switch will also swap the
state of Relay1.
Programming
1. Basic Command Class / Binary Switch Command Class
The Switch will respond to BASIC and BINARY commands that are part of the
Z-Wave system.
1-1 BASIC_GET / BINARY_SWITCH_GET
Basic Get Command: [Command Class Basic, Basic Get]
Basic Report Command:
Report OFF: [Command Class Basic, Basic Report, Value = 0(0x00)]
Report ON:[Command Class Basic, Basic Report, Value = 255(0xFF)]
Binary Switch Get Command:[Command Class Switch Binary, Switch
Binary Get]
Binary Switch Report Command:
Report OFF:[Command Class Switch Binary, Switch Binary Report, Value
=0(0x00)]
Report ON:[Command Class Switch Binary, Switch Binary Report, Value =
255(0xFF)]
1-2 BASIC_SET / SWITCH_BINARY_SET
[Command Class Basic, Basic Set, Value = 1~99, 255(0xFF)]: the load
attached to the Switch turns on.
[Command Class Basic, Basic Set, Value = 0(0x00)]: the load attached to
the Switch turns off.
[Command Class Switch Binary, Switch Binary Set, Value = 1~99,
255(0xFF)]: the load attached to the Switch turns on.
[Command Class Switch Binary, Switch Binary Set, Value = 0(0x00)]: the
load attached to the Switch turns off.
1. Z-Wave’s Groups (Association Command Class Version 2)
The Switch can be set to send reports to associated Z-Wave devices. It supports only
one association group and the group has one node support. Group1 support
SWITCH_BINARY_REPORT.
For group 1, the Switch will report ON/OFF status of Relay to controller.
3
2-1 Auto report to Grouping 1 (Maximum Node 1)
2-1-1 On/Off Event Report
When “on” or “off” state has been changed (ex. Press S1 S2 or include on/off
button), it will send Binary Switch Report to the nodes of Group1.
Binary Switch Report
ON:[Command Class Switch Binary, Switch Binary Report, Value
=(255)0xFF]
OFF:[Command Class Switch Binary, Switch Binary Report, Value
=0(0x00)]
2-1-2 Overload alarm report command
When PAN05 detect the overload, it will send Alarm Report to the node of
Group1.
The content of Alarm Report
Alarm report command:[Command Class Alarm, Alarm Report, Alarm Type
= 0x08, Alarm Level = 0xFF]
2. Z-Wave’s Configuration
Configuration
Parameter
1
2
3
4
Function Size
(Byte)
Edge or
1 1-3 1
Pulse
mode or
Edge-Tog
gle mode
Restore
1 0-2 1
switch
state
mode
Manual
1 0-1 1
On/Off
mode
LED
1 1-3 1
indication
Value Unit Default Description
1：Edge mode
2：Pulse mode
3：Edge-Toggle
mode
0 : Switch Off
1 : Last Switch
State
2 : Switch On
0：Disable
manual On/Off
1：Enable
manual On/Off
1：Show switch
state
2：Show night
mode
3 : One flash
mode
0：Disable auto
off function
1-0x7FFF：1 ~
32767seconds
0：Switch off
1：Ignore
2：Switch toggle
3：Switch on
5
6
mode
Auto off
timer
RF Off
command
mode
1 0-0x7F
FF
Second
1 0-3 0
0
3-1 Edge / Pulse / Edge-Toggle mode
Manual switch S1 and S2 can set to Edge mode or Pulse mode or Edge-Toggle
mode, default value is Edge mode.
3-1-1 Edge mode: this mode is suitable for the bi stable wall switch that has indicator
point on the switch, and the same position correspond to same state of relay1.
if the PAN05 relay change the state because of receiving Z-Wave RF
command, it may need two times of change (switch on to off or switch off to on)
to let relay back to the correspond state. Manual switch S2 is disabled in
this mode.
3-1-2 Pulse mode: this mode is suitable for the toggle type wall switch to swap the
state of Relay1.
3-1-3 Edge-Toggle mode: this mode is suitable for the normal bi-stable switch, every
time when change the state of the wall switch will also swap the state of
Relay1.
3-2 Restore Switch State Mode
Whenever the AC power reconnected to PAN05, it will set the switch to Off、On or
Last switch state, default value is Last switch state.
4
3-3 Manual On/Off Mode
Symptom
Cause of Failure
Recommendat
ion
The Switch not working and
The On/Off function of S1、S2 and learn switch can be disabled or enabled by this
parameter, default value is Enable. But the learning operation won’t be affected.
3-4 LED indication Mode
3-4-1 Show switch state：LED on for switch on and off for switch off. The default
value is Show switch state.
3-4-2 Show night mode：LED off for switch on and on for switch off.
3-4-3 One Flash mode：When the state of switch changes, LED will be on only one
second, then LED keeps off.
3-5 Auto Off timer
When auto off timer is equal to 0, the auto off function will be disabled. Whenever
the switch is set to on, the auto off timer begin to count down. After the timer
counts to zero, PAN05 will switch off automatically. The default value is disable
auto off function.
3-6 RF Off command mode
Whenever a RF Off command is received, BASIC_SET、BINARY_SWITCH_SET、
SWITCH_ALL_OFF, it could be interpreted as Switch Off、Switch On、Switch
Toggle, or it would be ignored. The default value is Switch Off.
4. Protection Command Classes
PAN05 supports Protection Command Class version 2, it can protect the switch
against unintentionally control by e.g. a child. And it can also protect the switch
from being turned off by setting it in “No RF Control” state.
After being set to “Protection by sequence” state, any intentional pressing of
On/Off button or S1/S2 should be hold longer than 1 second, or the switch state
will not change.
However, the operation of learn function does not change, because learning will
not be protected.
5. Command Classes
The Switch supports Command Classes including…
* COMMAND_CLASS_ZWAVEPLUS_INFO_V2
* COMMAND_CLASS_VERSION_V2
* COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
* COMMAND_CLASS_SECURITY
* COMMAND_CLASS_DEVICE_RESET_LOCALLY
* COMMAND_CLASS_ASSOCIATION_V2
* COMMAND_CLASS_ASSOCIATION_GRP_INFO
* COMMAND_CLASS_POWERLEVEL
* COMMAND_CLASS_SWITCH_BINARY
* COMMAND_CLASS_BASIC
* COMMAND_CLASS_SWITCH_ALL
* COMMAND_CLASS_CONFIGURATION
* COMMAND_CLASS_ALARM
* COMMAND_CLASS_PROTECTION_V2
* COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
Troubleshooting
LED off
The Switch LED
illuminating, but cannot
control the ON/OFF
Switch of the load attached
The Switch LED
illuminating, but the
detector cannot control
the Switch
LED keep flashing
continuously, but cannot
control
1. The Switch is not
connect to the Main
power
2. The Switch break
down
Check if the load connect
into the Switch has its
own ON/OFF switch
1. Not carry out
association
2. Same frequency
interference
Overload occurs Remove the load attached or check
1. Check power connections
2. Don’t open up the Switch and send
it for repair.
Set the ON/OFF switch of the load
attached to ON
1. Carry out association
2. Wait for a while to re-try
max. load cannot exceed
85 °C (230Vac/120Vac)
5
Specification
100 ~240V
AC
other household wastes throughout the EU. To prevent possible harm to
Operating Voltage
Maximum Load 85°C (230Vac/120Vac)
Range Minimum 30 m in door 100m outdoor line of sight
Operating Temperature 0°C ~ 40°C
Frequency Range PAN05-1: 868.40MHz; 869.85MHz(EU) /
PAN05-2: 908.40MHz; 916.00MHz(USA/Canada) /
PAN05-3: 922.5MHz/ 923.9MHz/ 926.3MHz (Taiwan/JP)
** Specifications are subject to change and improvement without notice.
FCC ID : RHHPAN05
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
Warning:
1. Plug out to disconnect from power supply; do not plug in line.
2. Do not exceed the max rating
Disposal
This marking indicates that this product should not be disposed with
the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and
collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe recycling.
Company of License Holder：Philio Technology Corporation
Address of License Holder：8F.,No.653-2,Zhongzheng Rd., Xinzhuang Dist., New
Taipei City 24257,Taiwan(R.O.C)
FCC Interference Statement
FCC Interference Statement
FCC Interference StatementFCC Interference Statement
This equipment has been tested and found to comply with the limits for
encouraged to try to correct the interference by one of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment.
This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
6
Loading...