HP890i
Specifications: HP890i
System Type
Frequency Response (- 3 dB)
Low Frequnecy (-10 dB)
Max. Program Power
Max. Continuous Power
Max. SPL dB @ 1 M
Sensitivity dB @ 1W/1M
Impedance (nominal)
Coverage Angle (-6 dB @ 2Hz)
Coverage Angle (-6 dB @ 4 kHz)
Directivity Factor (Q)
Directivity Index (DI)
Tap Selector
Transformer Taps
70.7 V Output 100 V Output 25 V Output
120 W 115 dB 120 W 115 dB 16 W 106 dB
64 W 112 dB 64 W 112 dB 8 W 103 dB
32 W 109 dB 32 W 109 dB 3.8 W 100 dB
16 W 106 dB 16 W 106 dB 1.9 W 97 dB
Transducers
Low Frequency Driver
High Frequency Driver
Low Frequency Voice Coil
Crossover Frequency
Network Type
Low Pass
High Pass
Enclosure Material
Motor Board
Grille
Inputs
Colors
Height
Diameter
Weight
Shipping Weight
Accessories
Included
Optional
Packaging
1
Frequency response is measured in full space.
2
Continuous power rating, EIA-426-B test.
3
2.83 Volts at a distance of 1 meter.
SoundTube continually develops new product innovations and improvements. Updates to existing
products without prior notice are an example of SoundTube’s drive for constant improvement.
© 2006 SoundTube Entertainment. All rights reserved. PN TS-HP590 REV 04.04.06
Preliminary Technical Information for System Engineers
8” Coax, compression tweeter w/ 1” exit, open-ceiling, ported (120
1
1
2
3
Watt transformer for 25/70.7/100 Volt or voice coil / 8 Ohm direct)
73 Hz - 22 kHz
63 Hz - 22 kHz
250 Watts
125 Watts
115 dB
94 dB
8 Ohm
122º
130º
4.64 (Averaged 100 Hz - 10 kHz); 4.48 @ 2 kHz
8.34 dB (Averaged 100 Hz - 10 kHz); 6.51 dB @ 2 kHz
5-Position rotary switch with voice coil direct (8 Ohm)
1 x 203 mm (8 in) Treated fiber cone, cloth surround
1 Compression driver with waveguide and 25.4 mm (1 in) exit
34 mm (1.36 in)
2.4 kHz
12 dB per octave, 2nd order
12 dB per octave, 2nd order
Injection molded ABS, glass fiber reinforced
Cast aluminum with integrated heat sink
Iridite-plated steel with powder-coat finish
4 Pin, 5 mm Euroblock for individual or daisy chain connection
Black or white
437.7 mm / 17.23 in
376.5 mm / 14.82 in
10.0 kg / 22.1 lbs
N/A
Hanging hardware, Euroblock connector & terminal weather boot
Surface-Mount Bracket (AC-RS-SM8)
1 per box
Open Ceiling Speaker
Mounting hardware included
Preliminary Technical Information
The information in this document reflects
preliminary data. Items including polar
plots, frequency, phase and impedance
response graphs will be added when final
data are available.
Key Features
• BroadBeamHP® waveguide technology
delivers a consistent dispersion pattern for
maximum coverage area per speaker (up
to 10 kHz, EASE
™
documented).
• One 203 mm (8.0 in) treated fiber driver
and one compression driver with a 25.4 mm
(1 in) exit mounted to a proprietary castaluminum M8
™
baffle and heat sink.
• 120 Watt transformer and high output (115 dB)
for the sound reinforcement and PA markets.
• Easy-access 5-position selectable tap
switch for 25, 70.7, and 100 Volt applica
tions with voice coil/8 Ohm direct simpli
fies ordering and inventory tracking.
• Weatherized components for indoor/
outdoor applications
• 94 dB Average sensitivity offers high-output
capabilities and reduced amplification costs.
• Includes hanging hardware with aircraft
cables and integrated SpeedClamp™ selflocking wire grip for fast, easy & secure
installation. Also includes Euroblock con
nector & terminal weather boot.
• Optional accessory: surface-mount
bracket (AC-RS-SM8).
• High quality black or white paint finish.
Description
The HP890i is a premium 8.0” 2way, ported high-efficiency, high-SPL
loudspeaker for distributed or 8 Ohm
applications. The HP890i incorporates a
dedicated 8.0” treated fiber driver and
high-power compression transducer
with a BroadBeamHP
deliver a consistent dispersion pattern
and superb intelligibility for the fore
ground music, sound reinforcement and
PA markets. The HP890i incorporates a
120 Watt transformer with a 5-position
tap switch and voice coil/8 Ohm direct
position. Hanging hardware is included
and features a fast-action SpeedClamp™
for easy and secure installation.
Applications
Engineered for installations requiring
full-range background/foreground music
plus paging, the HP890i delivers a smooth
®
waveguide to
-
-
-
HP890i
Preliminary Technical Information for System Engineers
Open Ceiling Speaker
Frequency Response
N/A
Phase/Impedance Reponse
and even coverage pattern. Ideal for
warehouses, gyms, aerobic rooms, air
ports, super stores, arenas, theme parks,
transportation and shipping centers,
stadiums and other high-SPL or longthrow applications.
For professional sound reinforcement
applications, indoors or out, the HP890i
includes a cast-aluminum M8 motorboard, iridite-plated, powder-coated
steel grille, durable enclosure design
and terminal weather boot.
-
BroadBeamHP® Wide
Dispersion Technology
SoundTube’s proprietary BroadBeamHP
high-frequency compression driver with
a 1” exit mated to a treated fiber woofer.
The BroadBeamHP
a 90º dispersion pattern across the upper
registers of the frequency spectrum (up to
10 kHz, EASE
is an audio system with fewer speakers,
reduced power needs, shorter installation
time and cost savings on shipping and labor.
®
technology incorporates a
®
technology delivers
™
documented). The result
N/A
Beamwidth (-6 dB) Directivity Index (DI)
N/A
N/A
HP890i
Open Ceiling Speaker
Preliminary Technical Information for System Engineers
Patented SoundTube
Technologies
SoundTube Entertainment is consistently developing new technologies that
enhance audio product performance.
SoundTube Entertainment innova
tions are protected by multiple U.S. and
international patents, which explicitly
cover SoundTube dome, enclosure,
mounting and dispersion technolo
gies. SoundTube Entertainment actively
defends it patents in order to protect
SoundTube resellers and end-users.
-
-
Technical Data and
Specification Tools
Technical Data
SoundTube Entertainment strives to
provide complete and effective technical
information and data to dealers, engi
neers and designers. All data are avail
able from SoundTube Entertainment or
at www.soundtube.com.
Data Acquisition
All performance data acquired at
SoundTube’s Technical Measurement
Center (TMC) are analyzed using a vari
-
-
-
ety of standard measurement techniques,
including Measured Length Sequence
(MLS) and Time Delay Spectrometry
(TDS). Performance, development and
data acquisition tools include: Gold Line
TEF 20, CLIO, LMS, LEAP, and propri
etary modeling software. EASE
are acquired through an automated TEF
20/Outline/EASE
EASE™ Data
SoundTubeSPEC™
SoundTube speaker placement software
™ interface.
– 3-D polar plots.
– Proprietary
-
™ data
.
Architectural Specifications
The loudspeaker shall consist of a 203
mm (8 in) low-frequency transducer and
a high frequency transducer with a 1”
exit and a frequency-dividing network
installed in a ported enclosure. The lowfrequency voice coil diameter shall be 34
mm (1.36 in).
The performance specifications of a
typical production unit shall be as follows:
Useable frequency response shall extend
from 63 Hz – 22 kHz (-10 dB, no external
equalization). Measured sensitivity (2.83
Volt input, 1 meter) shall be at least 94
dB. The speaker shall have a nominal
impedance of 8 Ohms and be available for
25/70.7/100 Volt modes with a voice coil/8
Ohm direct. The frequency-dividing net
work shall have a crossover frequency of 2.4
kHz with a slope of 12 dB per octave (2nd
order). Rated power capacity shall be at least
125 Watts continuous power (RMS), and
shall conform to EIA-426-B testing. Maxi
mum continuous output at 1 meter shall be
115 dB.
The low-frequency transducer shall have a
treated fiber cone and cloth surround.
Installation for the HP890i shall be by 10’
aircraft cable affixed to the speaker chassis via
hook. For seismic and safety redundancy, a
secondary aircraft cable shall be included and
shall attach to the speaker chassis via hook
and cable system. The external wiring shall
be a 4-pin 5 mm Euroblock connector for 8
Ohm or distributed systems and shall accept
from 10 – 22 gauge wire. The system shall be
for indoor and outdoor applications and have
a weather-resistant terminal boot covering all
wire connections.
The enclosure shall be constructed of
injection-molded, glass reinforced ABS. The
grille shall be constructed of iridite-plated,
powder-coated steel for lasting performance
-
-
Polar Plots
N/A
Technical data, EASE™ plots, SoundTubeSPEC™ software & product downloads available at www.soundtube.com
HP890i
Preliminary Technical Information for System Engineers
Open Ceiling Speaker
Mechanical Drawings
363.6 mm (14.31 in)
Included Accessories
307.3 mm (12.10 in)
in the elements. Overall cabinet dimensions shall be no more than 437.7 mm
(17.23 in) in height by 376.5 mm (14.82 in) in
diameter and weigh no more than 10.0 kG
(22.1 lbs).
The HP890i shall ship with hanging
hardware, Euroblock connector and ter
minal weather boot. Optional accessories
for the HP890i include surface-mount
bracket (AC-RS-SM8), 20’ hanging cable
(AC-RS-HH-20) and 10’ split loom tubing
(AC-SLT-10) for architectural applications.
The system shall be the HP890i with
hanging hardware for both low- and highimpedance applications.
SoundTube Entertainment
6430 North Business Park Loop
Park City, Utah 84098
Phone 435.647.9555
Fax 435.647.9666
Toll Free 800.647.TUBE
www.soundtube.com
Hanging Hardware: Main & Safety
Cables w/ SpeedClamp™
SoundTube’s hanging cable kit incorpo
rates hanging & safety cables & fasten
ers for an integrated and easy-to-install
system. Hanging & safety cables are
infinitely adjustable to 2.74 M (9.0 ft).
Optional Accessory
463.80 mm (18.26 in)
346.45 mm
(13.64 in)
Surface-Mount Bracket (AC-RS-SM8)
SoundTube Entertainment manufactures a complete line of speakers for:
Open-Ceiling • In-Ceiling • Sur face-Mount • Outdoor • Sound-Focusing
-
-
All SoundTube products are designed and engineered in the USA.
Loading...