Phase Technology FP User Manual

FP Series
Install Instructions For:
Motion Sensor
1.435.647.9555
|
800.647.TUBE
|
www.soundtube.com
ATTENTION
The FP pod comes with the motion sensor lens preset to a wide angle and will trigger audio activation from movement beyond the diameter of the dome. For applications with a narrow motion sensor angle, follow these instructions. The narrow motion sensor lens will trigger audio activation only when someone is standing directly underneath the dome.
Dome Clamp
Motion Sensor Accessory Contents
1 FP Pod with wide lens 1 Narrow lens
FP Speaker Pod
Motion Sensor Pod Cover
Motion Sensor
Motion Sensor lens (narrow)
Motion Sensor lens (wide)
(Optional, included)
(Standard)
© 2005 SoundTube Entertainment, Inc. All rights reserved. PN INS-FP6-MS REV 01.12.06
Warning Warning
SoundTube speakers must be installed by a professional audio installer/contractor. For safety and for optimum audio performance, installer must follow all directions issued by SoundTube Entertainment.
Do not spec or install speaker near support beam, ventilation duct or other structure that may interfere with speaker function or dispersion.
FP Series
Install Instructions For:
Motion Sensor
To adjust the sensor from wide angle to narrow angle:
1.435.647.9555
|
800.647.TUBE
|
www.soundtube.com
1. Unpack FP speaker pod
and FP Dome.
5. Place pod cover back on
2. Remove motion sensor
pod cover.
6. Complete.
FP unit.
Wiring Diagram for Motion Sensor
Power Source
(not included)
Voltage Sensor Controller
(not included)
Ground
Positive
Ground
White/ Green Signal wire
Orange White /
Orange
Brown White /
Brown
for 5 Volt ttl signal
Blue White (unused)
Blue Signal wire for
1k to 12 Volt pullup
Green (unused)
Cat V Wire From Pod
Signal wire
3. Remove motion sensor lens. 4. Place narrow lens into pod
cover. Make sure lens is flush with outside of pod cover. Align the flat side of the lens w/ the flat side of the pod cover.
Power supply and voltage sensor control not included.
1. Attach the +12 V from the power supply to the Orange white and orange wire pair.
2. Attach the ground from the power supply to the brown
white and brown wire pair.
3. Attach the ground from the voltage sensor controller to the brown and white wire pair also.
4. Attach the signal wire to the white/green single wire.
5 Volt ttl signal (White/ Green Signal wire)
• 0 Volts = motion detected
• 5 Volts = no motion detected
• The green and blue/white wires are unused.
1k to 12 Volt pullup (Blue Signal wire)
• 12 Volts = motion detected
• 0 Volts = no motion detected
• The green and blue/white wires are unused.
FP SeriesFP Series
12 VDC
Power
supply
Install Instructions For:
SoundTube/Gilderfluke SD-25
FP6030-M FP6020-M Wiring diagram
Power 9-24 VDC
SD-25 Audio Repeater
Gilderfluke & Company
Line out Left
Burbank, califorina
1.435.647.9555 | 800.647.TUBE | www.soundtube.com
Line out right
Black Spk
Red Spk
Green Spk
White spk
Speakers
Left
Right
Power
9-24 vdc
Running
status
Jumper wire
Pin 5 to 10
Orange White Orange Cat V Pair
Brown White Brown Cat V Pair
A
Inputs
B
Blue Cat V
Notes
1- 12 VDC is the maximum power input from the power supply if using soundtube motion sensor
2- If more volume is needed the SD-25
can be bridged and run in mono mode. Internal jumpers need to be set for this mode. Please see Sd-25 configuration & installation instructions.
(Signal)
3- For operating and playback modes
please see SD-25 installation sheet.
Loading...