Phase Linear UMP-301 Owners Manual

UMP301

Owner's Manual/Manual del Usario/Manual de L'Utilisateur

AM/FM/CD/MP3/WMA Receiver

MUTE

SRC

SEL

DISP

UMP301 CD / MP3 / WMA / RECEIVER

ALBUM

MUSIC

ARTIST

INTRO

AS/PS

Receptor AM/FM/CD/MP3/WMA

AM/FM/CD/MP3/WMA Ampli-

BAND

RANDOMREPEAT

ST/MO

LO/DX

LOUD

Syntoniseur

UMP301

Para obtener instrucciones en Español, diríjase a la página 18.

PREPARATION

Getting Started

It’s a good idea to read all of the instructions before beginning the installation.

Contents

Installation Instructions.............................. 3

Wiring ........................................................ 5

Installing the Removable Faceplate .......... 6

Operating Instructions ............................... 7

CD Player Operating Instructions.............11

MP3 Player Operation............................. 13

Care and Maintenance............................ 15

Specifications .......................................... 16

Installation Requirements

This unit is designed for installation in cars, trucks and vans with an existing radio opening. In many cases, a special installation kit will be required to mount the radio to the dashboard. These kits are available at electronics supply stores and car stereo specialty shops. Always check the kit application before purchasing to make sure the kit works with your vehicle. If you need a kit but cannot locate one, call our customer support line at 1-800-323-4815. (U.S.A. and Canada only.)

Tools and Supplies

The following tools and supplies are needed to install the radio.

• Torx type, flathead and Philips screwdrivers

• Wire cutters and strippers

• Tools to remove existing radio (screwdriver, socket wrench set or other tools)

• Electrical tape

• Crimping tool

• Volt meter/test light

• Crimp connections

• 18 gauge wire for power connections

• 16-18 gauge speaker wire

Speaker Requirements

Only connect speakers rated with a load impedance of 4 ohms. Speakers with a load impedance of less than 4 ohms could damage the unit.

Disconnect Battery

Before you begin, disconnect the battery negative terminal.

Pour des instructions en Francais, référez-vous à la page 34.

Toll-Free Installation Assistance

If you require assistance, contact Technical Support at 1-800-323-4815 from 8:30 a.m. to 7:00 p.m. EST Monday through Friday and from 9:00 a.m. to 5:00 p.m. EST on Saturday. (U.S.A. and Canada only.)

UMP301

INSTALLATION INSTRUCTIONS

Using the Mounting Sleeve

1. Slide the mounting sleeve off the chassis. If it is locked into position, use the removal tools (supplied) to disengage it.

2. Check the dashboard opening size by sliding the mounting sleeve into it.

If the opening is too small, carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check for sufficient space behind the dashboard for the radio chassis.

3. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard.

4. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. Follow the wiring diagram carefully and make certain all connections are secure and insulated with wire nuts or electrical tape. After completing the wiring connections, turn the unit on to confirm operation (vehicle ignition must be on). If the unit does not operate, re-check all wiring until the problem is corrected.

5. Make sure the radio is right-side up, then carefully slide the radio into the mounting sleeve until it is fully seated and the spring clips lock it into place.

BEND TABS

6. Secure the rear of the unit to the car body using the mounting bolt and rubber cushion.

7. Test the radio using the Operating Instructions that follow.

SPRING CLIP

MOUNTING SLEEVE

RUBBER CUSHION

MOUNTING BOLT

CAUTION: For proper operation of the CD player, the chassis must be mounted within 20° of horizontal. Make sure the unit is mounted within this limitation.

RADIO

TRIM RING

INSTALLATION INSTRUCTIONS

UMP301

Installation Using a Kit

If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with the installation kit to attach the radio to the mounting plate supplied with the kit.

1. Wire and test the radio as described in step 4 of “Using the Mounting Sleeve”.

2. Install the radio mounting plate assembly to the sub-dashboard according to the installation kit instructions.

3. Attach the support strap to the radio and dashboard as described in step 6 of “Using the Mounting Sleeve”.

4. Replace the dashboard trim panel.

ISO Installation

This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. Please consult with your local car stereo specialty shop for assistance on this type of installation.

1. Remove the existing factory radio from the dashboard or center console mounting. Save all hardware and brackets as they will be used to mount the new radio.

ISO INSTALLATION

2. Carefully unsnap the plastic frame from the front of the new radio chassis. Remove and discard the frame.

3. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio.

CAUTION: Do not exceed M5 X 6 MM screw size. Longer screws may touch and damage components inside the chassis.

4. Wire the new radio to the vehicle as described in step 4 of “Using the Mounting Sleeve”.

5. Mount the new radio assembly to the dashboard or center console using the reverse

procedure in step 1 of “Using the Mounting Sleeve”.

Removing the Radio

To remove the radio after installation, remove the trim ring by lifting in the center and pulling it off from either side. Insert the removal keys straight back until they lock, then pull the radio out. If removal keys are inserted at an angle, they will not lock properly and will not release the unit.

REMOVING THE RADIO

UMP301

WIRING

Auxiliary Input

Antenna Connector

Amplifier Wiring

Connect line out for optional

external amplifiers. The red

connector is for the right and the

white connector is for the left.

Gray

15A

15 Amp Fuse

Power Antenna

Connect to power antenna

Blue

or amplifier. If not used, tape bare end of wire.

Black

Ground

Connect to ground terminal.

WARNING! Never combine (bridge) outputs for use with 1 speaker.

WARNING! Never ground negative speaker leads to chassis ground.

CAUTION: Failure to wire exactly as shown may cause electrical damage to the radio.

LF/AVG

LR/ARG

White/Black (-)

White (+)

Green/Black (-)

Green (+)

Gray/Black (-)

Gray (+)

Violet/Black (-)

Violet (+)

Yellow

Red

RF/AVD

RR/ARD

Memory/Battery

Connect to battery or 12 volt power source that is always live. The radio will not work if this wire is not connected.

Accessory/Ignition

Connect to existing radio wire or radio fuse.

Fuses

When replacing a fuse, make sure the new fuse is the correct type (ATO) and amperage. Using an incorrect fuse could damage the radio.

INSTALLING THE REMOVABLE FACEPLATE

Faceplate Installation

To install the faceplate, slip the right edge of the front panel into the radio then gently press the left side into place.

Faceplate Detachment

UMP301

To remove the faceplate, press the release button, and pull gently on the left side of the front panel. For safekeeping, store the front panel in the protective case provided.

Handling Precautions

• Make sure the front panel is right-side-up when attaching it to the chassis as it cannot be attached when up-side down.

• Do not press very hard on the front panel when attaching it to the chassis. No more than light to moderate pressure is needed.

• When attaching the front panel, make sure it is centered in the chassis frame and is pressed straight into position.

• Do not drop the front panel.

• Do not put pressure on the display or control buttons when handling the front panel.

• Do not touch the electrical terminals on the front panel or main unit.

• Remove dirt or foreign substances with a clean, dry cloth only.

SRC

SEL

• Do not expose the front panel to extreme temperatures or direct sunlight.

• Keep volatile agents such as benzene, thinner or insecticides away from the front panel.

• Do not disassemble the front panel.

• When taking the front panel with you, please use the supplied carrying case to protect the panel from dirt and damage.

BAND

LOUD

LO/DX

UMP301 CD / MP3 / WMA / RECEIVER

AS PS

DISP

INTRO

RANDOMREPEAT

ST/MO

• Make sure there is no dust or dirt on the electrical terminals on the back of the panel as this could cause intermittent operation or other malfunctions.

UMP301

OPERATING INSTRUCTIONS

Power On/Off Button

Press the power button (1) (or any button except eject or release) to turn the unit on.

Press and hold the power button to turn the unit off.

Audio MUTE

Press the power/MUTE button (1) to silence the volume from the system. “MUTE ON” will appear on the display panel. Press MUTE again to return the volume level to the setting that was in use before the Mute function was activated.

Liquid Crystal Display Panel

The Liquid Crystal Display (LCD) panel displays the frequency, time and all activated functions.

NOTE: It is a characteristic of LCD panels that, if subjected to cold temperatures for an extended period of time, they may take longer to illuminate than under normal conditions. In addition, the visibility of the numbers on the LCD may slightly decrease. The LCD read-out will return to normal when the temperature inside the vehicle increases to a normal range.

3 4

Volume Control

To increase the volume level, press the volume + button (3). To decrease the volume level, press the volume down – button (3). The volume will increase/decrease and the level will be shown on the display panel from a minimum of “VOL 0” to a maximum of “VOL 47”. The display will automatically return to the normal indication 5 seconds after the last volume adjustment or when another function is activated. The volume control is also used in conjunction with the SEL button (4) to adjust the bass, treble, balance and fader levels.

MUTE

SRC

SEL

UMP301 CD / MP3 / WMA / RECEIVER

AS/PS

DISP

ALBUM

MUSIC

ARTIST

INTRO

Bass Control

To adjust the bass level, first select the Bass mode by pressing the SEL button (4) until “BAS” appears on the display panel. Within five seconds, press the volume +/– buttons (3) to adjust the bass response from a minimum of “BAS -7” to a maximum of “BAS 7”. “BAS 0” represents a flat response.

NOTE: You cannot adjust the Bass or Treble options when the Preset Equalizer (DSP) is activated.

BAND

RANDOMREPEAT

ST/MO

LO/DX

LOUD

OPERATING INSTRUCTIONS

UMP301

Treble Control

To adjust the treble level, press the SEL button (4) until “TRB” appears on the display panel. Within five seconds, press the volume +/– buttons (3) to adjust the treble from a minimum of “TRB -7” to a maximum of “TRB 7”. “TRB 0” represents a flat response.

Left/Right Balance Control

To adjust the left/right speaker balance, press and release the SEL button (4) until the “BAL” indication appears on the display panel. Within five seconds, press the volume +/– buttons (3) to adjust the balance between the left and right speakers from “BAL 10L” (full left) to “BAL 10R” (full right). “BAL 0” represents an equal balance level between the left and right speakers.

Front/Rear Fader Control

To adjust the front/rear speaker balance, press the SEL button (4) until “FAD“ appears on the display panel. Within five seconds, press the volume +/– buttons (3) to adjust the balance between the front and rear speakers from “FAD 10F” (full front) to “FAD 10R” (full rear). “FAD 0” represents an equal balance level between the front and rear speakers.

4 4

Equalizer Selector (DSP)

1. Press and hold the SEL button (4) for more

than 2 seconds to access the menu.

2. Continue pressing the SEL button to select

“DSP Mode”.

3. Press the volume +/– buttons (3) to select

one of the following modes: “POP”, “ROCK”, “CLASSIC”, “FLAT” or “DSP OFF”.

NOTE: When the DSP function is turned off, the unit returns to the user-set bass and treble levels.

MUTE

SRC

SEL

UMP301 CD / MP3 / WMA / RECEIVER

AS/PS

DISP

ALBUM

MUSIC

ARTIST

INTRO

Audible Beep

Press and hold the SEL button (4) for more than 2 seconds to access the menu. Continue pressing the SEL button to access the Beep Tone menu. Press the volume +/– buttons (3) to select “BEEP ON” or “BEEP OFF”.

MP3 Multi-Session (MULT)

MULT ON: Will read multi-session and mixedmode discs. MULT OFF: Will read single session discs only.

RANDOMREPEAT

ST/MO

LO/DX

BAND

LOUD

UMP301

OPERATING INSTRUCTIONS

Seek Mode Selector

1. Press and hold the SEL button (4) for more

than 2 seconds to access the menu.

2. Continue pressing the SEL button to select

“SEEK” mode.

3. Press the volume +/– buttons (3) to select

“SEEK 1” or “SEEK 2”.

• SEEK 1: Station search will stop when the next station is received.

• SEEK 2: Station search will stop when the tune/track ( , ) button (6a or 6b) is released and the next station is received.

Turn On Volume Setting

1. Press and hold the SEL button (4) for more

than 2 seconds to access the menu.

2. Continue pressing the SEL button to select

“VOL ADJ” mode.

3. Press the volume +/– buttons (3) to select

one of the following modes: “VOL LAST” or “VOL ADJ”.

• VOL LAST: When the unit is turned on, the volume will resume at the level selected when last turned off.

• VOL ADJ: After selecting “VOL ADJ”, use the volume +/– buttons (3) to set the desired turn-on volume level.

AM/FM Band Selector (BAND)

During radio play, each time the BAND button (5) is pressed, the radio band changes. The indications “AM1”, “AM2”, FM1”, “FM2”, or “FM3” will appear on the display panel according to your selection.

Tuning Control

Press the tune/track ( ) button (6a) to manually tune the radio higher, or the tune/track ( ) button (6b) to manually tune lower. Press and hold either the up or down tune/track button (6a and 6b) to seek the next strong station.

FM Mono Select (ST/MO)

During FM radio operation, the ST/MO button (7) is used to select monaural or stereo reception of the broadcast signal. Under normal reception conditions, the unit should be left in the stereo mode (indicated by “STEREO” when tuned to an FM stereo signal). If the signal is too noisy for comfortable listening, press the ST/MO button; the “STEREO” indication will disappear from the display panel and “MONO” will appear. To return to stereo reception mode, press the button again.

Auto-Store/Pre-Set Scan

(AS/PS)

Press the AS/PS button (8) momentarily to scan the 6 stations in the pre-set memory for all FM bands. The unit will stop at each pre-set station for 10 seconds. Press AS/PS again to stop scanning and select the current frequency. Press and hold the AS/PS button for more than 2 seconds to activate the Auto-Store Tuning feature. The radio will automatically scan the band in use and enter the six strongest stations into the pre-set memory positions for that band. Auto-Store will erase any stored stations.

Local Button (LO/DX)

During radio operation, received signals are usually in stereo mode as indicated by the “ST” icon; however, when the signals are weak or intermittent, you can activate the Local mode by pressing the LO/DX button (9) (“LOCAL” appears on the display). This mode favors access to local stations whose signals are much stronger; thereby improving radio reception. Press the LO/DX button again to terminate Local receive mode (“- DX -” appears on the display).

OPERATING INSTRUCTIONS

UMP301

Loudness Control (LOUD)

When listening to music at low volume levels, this feature will boost the bass and treble ranges to compensate for the characteristics of human hearing. Press and hold the LOUD button (10) to activate this feature as indicated by a beep tone and “LOUD ON” appearing on the display panel. (“LOUD” remains on the display.) Press and hold the button again to turn the Loud function off. “LOUD” will disappear.

Display Selector (DISP)

This unit can display either the clock time or radio frequency/CD player functions. Press the DISP button (11) to display the time for approximately 5 seconds. The correct time-ofday can be set by pressing and holding the DISP button.

Setting the Clock

To set the clock, perform the following steps:

1. Press the DISP button (11) to display the

clock.

2. Press and hold the DISP button (11) until the

time display flashes.

3. Within 5 seconds, press the volume – button

(3) to adjust the minutes to the desired setting.

4. Press the volume + button (3) to adjust the

hour and the AM/PM indication to the desired time.

5. Press the DISP button again to return to

radio frequency.

– Station Pre-Set Memory

To set any of the 6 pre-set memory buttons , use the following procedure:

1. Turn the unit on and select the desired band.

2. Select the first station to be pre-set using the tune/track buttons (6a and 6b).

3. Press and hold a preset button until you hear a confirmation tone. The preset number appears on the display panel. The station is

MUTE

SRC

SEL

UMP301 CD / MP3 / WMA / RECEIVER

AS/PS

DISP

ALBUM

MUSIC

ARTIST

INTRO

now stored and can be recalled at any time by pressing the correct preset button.

4. Repeat the above procedure for the remaining 5 presets for the current band. Six stations can be stored for each band.

RANDOMREPEAT

ST/MO

LO/DX

BAND

LOUD

6b8

UMP301

CD PLAYER OPERATING INSTRUCTIONS

Disc Slot

With the label surface facing up, gently insert the disc into the slot until the soft-loading mechanism engages and disc play begins. “S CDP” will appear on the display panel. Once loaded, the track number and elapsed time will appear.

NOTE: The unit is designed for play of standard 5” (12 cm.) compact discs only. Do not attempt to use 3” (8 cm.) CD singles in this unit, either with or without an adaptor, as damage to the player and/or the disc may occur. Such damage will not be covered by the warranty on this product.

Mode Selector (SRC)

Press the SRC button (13) to change between CD player, radio, and Aux In operation. The current mode is indicated on the display panel. During CD player operation, this button may be used to change to radio without ejecting the disc.

Track Selector

The Track Select functions are used to quickly access the beginning of a particular track. Each time the tune/track ( ) button (6a) is pressed,

the next higher track number is selected, as shown on the display panel. Each time the tune/ track ( ) button (6b) is pressed, the next lower track number is selected, as shown on the display panel.

Cue/Review Functions

Press and hold the tune/track ( ) button (6a) to advance rapidly forward or the tune/track ( ) button (6b) to advance rapidly backward. During either function, the elapsed time of each track will be shown on the display panel.

MUTE

SRC

SEL

UMP301 CD / MP3 / WMA / RECEIVER

AS/PS

DISP

ALBUM

MUSIC

ARTIST

INTRO

Electronic Skip Protection

Electronic skip protection (ESP) can be activated to assist with playback when rough, uneven road conditions are encountered. To turn ESP on/off:

1. Press the AS/PS button (8) during disc playback to stop disc play.

2. Press AS/PS again to toggle the ESP function on/off.

3. Press AS/PS again to resume playback.

RANDOMREPEAT

ST/MO

LO/DX

BAND

LOUD

CD PLAYER OPERATING INSTRUCTIONS

UMP301

Disc Play/Pause Select

Press the 1/ button (14) to freeze disc playback. Press 1/ again to resume disc playback.

Track INTRO Scan

During disc play, press the 2/INTRO button (15) to play the first 10 seconds of each track (the “INT” icon will illuminate at the top of the display). When a desired track is reached, press the 2/INTRO button again to cancel the function and play the selected track. Track Scan mode can also be canceled by activating the Repeat (16) or Random (17) functions.

Track REPEAT Play Select

During disc play, press the 3/REPEAT button (16) to repeat play of the selected track (the “RPT” icon will illuminate at the top of the display). Play of the track will continue to repeat until 3/REPEAT is pressed again and the “RPT” indication disappears from the display panel. Repeat Play mode can also be canceled by activating the Intro (15) or Random (17) functions.

17 20

RANDOM Play Select

During disc play, press the 4/RANDOM button (17) to play the tracks on the disc in a random, shuffled order (the “RDM” icon will illuminate at the top of the display). In Random Play mode, you can press the tune/track buttons (6a and

When the disc eject button (20) is pressed, disc play is stopped, the disc is ejected, and the unit will change to radio operation. If the disc is not removed from the unit within 15 seconds, the disc will be re-loaded.

6b) to select tracks in a random order instead of the normal progression. Press 4/RANDOM again to cancel Random Play mode. Random Play mode can also be canceled by activating the Repeat (16) or Intro (15) functions.

MUTE

SRC

SEL

UMP301 CD / MP3 / WMA / RECEIVER

AS/PS

DISP

ALBUM

MUSIC

ART ST

INTRO

RANDOMREPEAT

Disc Eject Button

BAND

ST/MO

LO/DX

LOUD

UMP301

MP3 PLAYER OPERATION

Instructions for Insert/Eject, Play/Pause, Track Selection, Cue/Review, Scan, Repeat, and Random are the same for CD and MP3 operation. Please see the CD Player Operation section for information about these topics.

After inserting an MP3/WMA disc, the folder/file name and ID3 information will scroll across the screen in the following order:

• Elapsed playing time and track number

• Folder name and number

• File name and number

• Song title

• Album title

•Artist name

Track Search

1. Press the AS/PS (8) button once to enable

direct track searching (TRK SCH).

2. Press the SEL button (4) to select the last

digit of the track number (“001” will appear on the display with the “1” blinking).

3. Press the volume +/– buttons (3) to select

the last digit of the track number.

4. Press the SEL button to confirm the selec-

tion and move to the number field to the left (tenth position). Repeat for the third (hundredth) position, if necessary.

5. Press and hold the SEL button to play the

selected song/file.

NOTE: If the selected track number is higher than the maximum file number, the last file will be played.

File Search

1. Press the AS/PS button (8) twice to select

file search mode (FILE SCH).

2. Press the SEL button (4) to confirm.

3. Press the volume +/– buttons (3) to move to

the next or previous folder.

4. Choose to play the entire folder or a specific song in the selected folder:

MUTE

SRC

SEL

UMP301 CD / MP3 / WMA / RECEIVER

AS/PS

DISP

ALBUM

MUS C

ART ST

INTRO

• Press the SEL button to choose the folder, and then press the volume +/– buttons (3) to choose a specific song in the selected folder. Press the SEL button to play the selected track.

• Press and hold the SEL button to play all songs in the selected folder.

BAND

RANDOMREPEAT

ST/MO

LO/DX

LOUD

MP3 PLAYER OPERATION

Character Search

1. Press the AS/PS (8) button three times to

enable character search mode (CHAR SCH).

2. Press the SEL button (4) to select the first

character position.

3. Press the volume +/– buttons (3) to select

the first character of the desired track.

4. Press the SEL button to confirm and move

to the next character position.

5. Press the volume +/– buttons (3) to select

the second character of the desired song/ file.

6. Continue entering up to 8 characters.

7. Press and hold the SEL button to play the

selected song/file.

UMP301

MUTE

SRC

SEL

UMP301 CD / MP3 / WMA / RECEIVER

AS/PS

DISP

ALBUM

MUS C

ART ST

INTRO

BAND

RANDOMREPEAT

ST/MO

LO/DX

LOUD

UMP301

CARE AND MAINTENANCE

Your new radio/CD player does not require any maintenance. However, proper understanding of its use and handling will help you obtain maximum enjoyment of its capabilities. We recommend that you keep this manual for reference on the many features of this unit as well as how to set the clock. The following points should be observed:

• When cleaning the interior of the vehicle, do not get water or cleaning fluids on the unit.

• The CD player is a precision instrument and will not operate properly in extreme heat or cold. If such conditions occur, wait until the interior of the vehicle reaches a normal temperature before using the player.

• If the temperature inside the player gets too hot, a protective circuit will automatically stop play of the disc. In this case, allow the unit to cool before operating the player again.

• Never insert anything other than a 5" (12 cm) compact disc into the player as the mechanism can be damaged by foreign objects.

• Do not attempt to use 3" (8 cm) CD-Single discs in this unit, either with or without an adaptor, as damage to the player and/or disc may occur. Such damage will not be covered by the Warranty on this product.

• When not using the disc player, always remove the compact disc. Do not leave an ejected disc sitting in the disc slot as this can expose it to sunlight and other causes of damage.

• Do not attempt to open the unit chassis. There are no user-serviceable parts or adjustment points inside.

• When the vehicle warms up during cold weather or under damp conditions, condensation may appear on the lens of the disc player. Should this occur, the player will not operate properly until the moisture has evaporated.

• The unit is designed with a vibration dampening CD mechanism to minimize interruption of disc play due to normal vibration. When driving on rough roads, however, occasional sound skips may occur. This will not scratch or damage the disc and normal play will resume when the rough conditions cease.

Handling Compact Discs

Dirt, dust, scratches and warping can cause skips in the playback and deterioration of sound quality. Please follow these guidelines to take care of your compact discs:

• Carefully wipe fingerprints, dust and dirt from the disc’s playing surface with a soft cloth.

Wipe in a straight motion from the center to the outside of the disc.

• Never use chemicals such as record sprays or household cleaners to clean CDs, as they can irreparably damage the disc’s surface.

• Discs should be kept in their storage cases when not in use.

• Do not expose discs to direct sunlight, high temperatures or high humidity for long periods.

• Do not stick paper, tape or labels on disc surfaces.

RESET BUTTON

A Reset button is located behind the faceplate on the left side (the front panel must be removed to access the button). The Reset function should only be activated under the following circumstances: Upon initial installation after all wiring is completed; If there is a malfunction of any of the switches on the unit, pressing the Reset button may clear the system and return to normal operation.

SPECIFICATIONS

UMP301

CD-R and CD-RW Capability

Depending on media type and method of "recording/burning", some CD-R/RWs may be incompatible with this unit. After "recording/ burning", the session must be closed. Please refer to your software's recommended procedures for closing a disc/session. Review your recording software to familiarize yourself with the correct "recording/burning" procedures. We recommend using the latest versions of

ROXIO This unit will only recognize the CDDA

(Compact Disc Digital Audio), .MP3 and .WMA formats "recorded / burned" onto a CD-

R/RW. This unit does not support .WAV, .OGG or other formats.

or NEROTM burning software.

Technical Specifications

Marketing Power

160 watts Peak, 40 watts X 4

CEA Power

Power Output: 13 watts RMS X 4 channels into 4-ohms @ < 1% THD+N Signal to Noise Ratio: 70dBA below reference. (Reference: 1 watt, 4-ohms) Frequency Response: 20Hz to 20kHz, -3dB Reference Supply Voltage: 14.4VDC

CD Player

Signal to Noise Ratio @ 1kHz: >90dBA Frequency Response: 20Hz ~ 20kHz, -3dB Channel Separation @ 1kHz: > 60dB ESP (Electronic Skip Protection) Buffer Size: 2MB (16Mbit, not 16MB) CD: >10 seconds, nominal MP3: > 30 seconds, nominal WMA: >60 seconds, nominal

FM Tuner

Mono Sensitivity @ -30dB: 11dBf Quieting Sensitivity @ -50dB: 15dBf Stereo Separation @ 1kHz: >30dB Frequency Response: 30Hz ~ 12kHz, -3dB

AM Tuner

Sensitivity @ -20dB: 15uV Signal to Noise @ 1kHz: >50dB Frequency Response: 30Hz ~ 2kHz, -3dB

General

Power Supply: 11 to 16VDC, negative ground Fuses: 15 amp, ATO Dimensions: 7" X 7" X 2" (178mm x 178mm x 51mm)

Specifications subject to change without notice.

+ 36 hidden pages