Phase CS-6R/Micro, CS-8R/Micro, CS-6DVT/Micro Installation Instructions Manual

Install instructions for CS micro series:

T E C H N O L O G Y

CS-6R/Micro, CS-8R/Micro and CS-6DVT/Micro

Thank you for purchasing Phase Technology Professional Series
speakers. Before installing, please read through this installation
manual thoroughly.

Micro-Flange Grille

Flange

Flange Clamp
Screw (4x)

CS-6R/Micro, CS-8R/Micro

Aimable Tweeter

Flange

Flange Clamp
Screw (4x)

CS-6DVT/Micro

Choose the appropriate mounting location for each speaker.

When deciding upon a location, consider the following:

• Make certain your speaker wires can be run to or are accessible from these

locations.

• Make certain the wall or ceiling material is sturdy enough to support the
weight and vibration of the speakers.

• It is recommended that our pre-construction rough-in bracket assemblies

be used whenever possible in new construction.*

Micro-Flange Grille

• Make certain the area behind the speaker is free of obstacles such as wall

studs, electrical wiring, pipes, etc.

• Each speaker should be positioned properly, relative to the listening area

for good coverage.

• Audio performance and room-to-room isolation will be improved if there is
some berglass insulation placed loosely behind the speaker.

*The RB-14 for the 6” models and AC-CS8R-PCB is for the 8” model rough-in brackets are available for installations in new construction.

8005 W. 110th St., Suite 208 | Overland Park, KS 66210 | [phone] | www.phasetech.com | www.mseaudio.com

Install instructions for CS micro series, Page 2

Speaker Installation:

1. Using the supplied cutout template,carefully

mark the area to be cut out. Using a drywall knife or
saw, cut a hole in the drywall and prepare the
speaker wires for connection to the speaker

terminals.

Remove the grille from the speaker assembly.

2.

If it is necessary to paint the speaker grille to
match the ceiling, we recommend that you do
so with several light coats of matching spray paint.

3. Connect the speaker wires to the input

terminals on the rear of the speaker, making

sure no loose strands are exposed.

+

Red/positive Black/negative

_

**Note: for the CS-6DVT/Micro there are several

hookup options. For stereo point-source operation,
connect the speaker wires to the Left and Right
channel input terminals on the rear of the speaker.
Make sure no loose strands are exposed.Please
make sure to check your hookup polarity for proper

operation.

+

Red/positive Black/negative

_

R

100 v

100 v

1u6

1u6

1u6

1u6

Bi

100 v

100 v

L

Di

Stereo point-source conguration

For Surround/Mono: The CS-6DVT/Micro may
also be used as a surround speaker for home

theater applications. For the surround or MONO

mode of operation, connect your speaker wire

to either the left or right channel input as above.

Next connect 2 jumper wires from this same

input terminal to the corresponding input

terminals on the opposite side of the speaker.

Connect the red positive terminal to opposite red

terminal and black negative terminal to opposite
black terminal.

This speaker may be set to either the bi-pole or

di-pole mode of operation using the selector
switch on the rear panel.

Please note that the speaker is a 4 ohm speaker

in this conguration.

R

100 v

100 v

1u6

1u6

4. Carefully position the speaker in the

cutout hole. Using a Phillips screwdriver,

rotate the four clamps to secure the

speaker to the drywall.

CAUTION: Do not over-tighten.

5. Carefully replace the grille by pressing it

into the gap between the ange and the

baffle. Enjoy your new Phase Technology
speakers!

Surround or MONO conguration

8005 W. 110th St., Suite 208 | Overland Park, KS 66210 | [phone] | www.phasetech.com | www.mseaudio.com

1u6

1u6

Bi

100 v

100 v

L

Di